World-ClassAutoSecurity
Smart
Remote
Starter
TM
Owner'sManual
WARN ING
The Smart Re mote Starter III sys tem is de signed to be used ONLY on a fuel injected, gaso line or die sel pow ered ve hi cle with an auto matic trans mis sion.
In stall ing a Smart Re mote Starter III on a ve hi cle that has a man ual trans mis sion
poses an EX TREME SAFETY RISK! Never in stall a Clif ford re mote en gine start ing
prod uct on a man ual trans mis sion ve hi cle.
Al ways ex er cise good judg ment and com mon sense when us ing the
re mote starter:
• NEVER re motely start the ve hi cle in an en closed area with out suf fi cient ven ti la tion.
• NEVER al low chil dren ac cess to the re mote con trols.
• NEVER en gage the Short Stop nor one or both Auto Start fea tures if the
ve hi cle is in an en closed area with out ade quate ven ti la tion.
• NEVER re motely start or use the Short Stop fea ture with a per son or pet
in the car (ex haust fumes may leak into the pas sen ger com part ment).
• In case of trans mis sion slip page, NEVER re motely start the en gine if
you or some one else is di rectly be hind or in front of the ve hi cle.
Ta ble of Con tents
Stan dard Fea tures of the Smart Re mote Starter III ............... 2
Smart Re mote Starter III DOs and DON’Ts ................... 5
Your 4- button/12- channel re mote con trols .................. 6
How to use your key chain re mote con trol ................... 6
How to re motely lock/un lock the doors ....................7
How to re motely start/shut down the en gine .................. 7
Die sel com pati bil ity ...............................8
To drive the ve hi cle ...............................8
Short Stop ..................................... 8
In ter fac ing with fac tory theft de ter rent de vices ................9
AutoLock and Aut oUn Lock ........................... 9
Fault- proof starter in ter rupt ........................... 9
AutoAc ti va tion of the starter in ter rupt ..................... 9
AutoAc ti va tion of the door locks ........................9
Ul traSe cure coded valet mode ........................10
Defi ni tions .................................... 10
To en able valet mode .............................11
To exit valet mode ...............................11
Set ting your own se cret valet code ...................... 11
Ex am ple ..................................... 11
The Auto Start fea tures .............................12
Op tional re mote head light ac ti va tion and/or re mote trunk re lease .... 12
Op tional re mote con trolled win dow/sun roof clo sure ............ 12
User- selectable fea tures ............................ 13
Add ing new re mote con trols ......................... 14
How to erase the codes of lost or sto len re mote con trols ..........14
1
Stan dard Fea tures of the Smart Re mote Starter III
q✔ A Pair of 4-Button/12-Channel Remote Controls— You will never again
fumble with your car keys in the dark or bad weather. The remote controls give
you fingertip command of all these exciting convenience features from a typical
range of 300 feet:
• Remotely start or shut down your car’s engine and all preset accessories
(heater, air conditioner, etc.)
• Remotely lock and unlock your vehicle’s power door locks. For your
convenience and security, when you remotely unlock the doors, your vehicle’s
interior courtesy light(s) will turn on and stay on for 30 seconds or until you
drive.
• Remotely activate the headlights for any duration of your choice between one
second and two minutes to light your way to and from your vehicle.
• Remotely activate an optional trunk release.
•If your vehicle has a factory-installed theft deterrent device, your Smart Remote
Starter III can be set to transform it into a completely remote controlled vehicle
security system.
q✔ Automatic Safety Checks — Your Smart Remote Starter III automatically
ensures that all of the following safety conditions are met or the vehicle will not
be remotely started:
• Transmission must be in park
•Engine and ignition must be off
•Engine must not be overheated
•Hood must be closed
q✔ Anti-Theft Measures — Your car may be driven only after your ignition key is
turned to the “ON” position. If anyone other than you tries to drive the vehicle
while the engine is running, the system immediately shuts down the engine if:
•The transmission is moved out of the park position
•The brake pedal is pressed
•Engine rpm exceeds a certain threshold
•The hood is opened
q✔ Visual Acknowledgment — Your car’s parking lights will blink twice to
acknowledge initiation of the engine start-up process and then remain on for
continuing visual confirmation for as long as the engine idles under the control of
your Smart Remote Starter III.
2
Stan dard Fea tures of the Smart Re mote Starter III (cont.)
q✔ Cold Weather Cranking — Automatically cranks the engine for up to 10
seconds or until it starts, whichever occurs first. If the engine does not start, or
starts and then stalls, your Smart Remote Starter III will automatically try to
restart the engine up to two additional times.
q✔ AutoShutDown™ — The Smart Remote Starter III automatically shuts down the
engine after 30 minutes if the vehicle is left unattended.
q✔ StarterGuard™ — Prevents grinding of the starter if you inadvertently turn the
ignition switch to the starter position while the engine is running under the
control of your Smart Remote Starter III.
q✔ Remote Door Locking/Unlocking — A press of a button on the Smart Remote
Starter III remote control from up to 300 feet away will lock all the vehicle
doors. Remote door locking is visually confirmed by two flashes of the parking
lights. Press again and the doors will unlock, which is confirmed with a single
parking light flash.
q✔ AutoLock and AutoUnLock— For your safety when you begin driving, all the
doors automatically lock. Conversely, the doors automatically unlock when you
park and turn off the ignition. If you prefer, you may turn off one or both of these
features via program mode.
q✔ ShortStop Mode — Now you don’t need to shut off the engine when leaving
your car parked for a few moments (such as when stopping at a convenience
store or making a delivery). Just press button 2 while the engine is still running
and you can remove the keys, exit, and remotely lock the doors without shutting
down the engine.
q✔ AutoStart™ Battery Mode — Never again will you return to a dead car battery.
Whenever you wish, just a press of a button on your remote control sets the
system to continually monitor the vehicle battery while you are away. If the
battery’s voltage drops below a preset level, the system will automatically start
the engine and recharge the battery (to conserve battery power, the Smart Remote
Starter III will not activate the parking lights or any preset accessories in this
mode). Likewise, the system automatically shuts down the engine once the
battery is properly charged or after 30 minutes, whichever occurs first. If needed,
the process will repeat every eight hours until the battery is properly charged.
AutoStart is automatically canceled as soon as you drive your car.
3
Stan dard Fea tures of the Smart Re mote Starter III (cont.)
q✔ AutoStart Temperature Mode — You will never return to your car to find a
busted radiator or frozen oil in the crankcase. If you wish, you may set your
Smart Remote Starter III to AutoStart the engine if the engine temperature drops
below 15°F (–9°C). If you want to avoid any unwelcome surprise caused by cold
weather, you can set AutoStart to monitor both the engine temperature and the
voltage level just by pressing a button on your remote control.
q✔ Fault-Proof Starter Interrupt — When you remotely lock the doors, the Smart
Remote Starter III engages its starter interrupt circuit that prevents a thief from
starting the engine.
q✔ AutoActivation — Your Smart Remote Starter III is so smart, it will, if you
wish, automatically (”passively”) engage the starter interrupt and even lock the
doors if you forget to lock them with the remote control.
q✔ Smart Remote Trunk Release Capability — It’s the perfect feature when
carrying an armload of groceries. To ensure against accidental activation, the
trunk will remotely open only if the doors are unlocked and the vehicle is not
being driven (may require optional parts).
q✔ Remote Controlled Headlight Activation Capability — To light your way to
and from the vehicle, one press of a button on your Smart Remote Starter III
remote control will turn on your vehicle’s headlights for any duration of your
choice between one second and two minutes (requires an optional relay).
q✔ Remote Control Code Learning— With just a few flicks of a switch any time
or place, you may add up to four off-the-shelf Clifford remote controls to the
system. Just as easily, the code of a lost or stolen remote control can be deleted
so that the missing remote can never be used to control your system.
q✔ UltraSecure Coded Program Mode— Assures that no unauthorized person can
secretly add their own remote control, since the system’s programming mode can
be accessed only after you enter a personal code that you select.
q✔ Interfaces with Factory Theft Deterrent Devices— If your vehicle has a
factory-installed theft deterrent device, the Smart Remote Starter III can make it
a full-fledged remote controlled car alarm.
q✔ Automatic Transmission Required— The Smart Remote Starter III is intended
exclusively for vehicles with an automatic transmission.
4
Re mote Start ing DOs and DON’Ts
DOs
•Park in an open, well-ventilated area.
• Always engage the parking brake.
•Make sure you put the transmission in PARK before shutting
down the engine.
•Set the air conditioner, heater, defroster and other accessories
to the desired levels.
• Turn on your vehicle’s “recirculate” feature to warm/cool the
interior more efficiently.
• Before engaging one or both AutoStart features, make sure the
gas tank is full.
DON’Ts
You must al ways ex er cise good judg ment
and com mon sense when us ing the re mote starter:
• NEVER remotely start the vehicle in an enclosed area without
sufficient ventilation.
• NEVER allow children access to the remote controls.
•NEVER engage the ShortStop nor one or both AutoStart
features if the vehicle is in an enclosed area without adequate
ventilation.
•NEVER remotely start or use the ShortStop feature with a
person or pet in the car (exhaust fumes may leak into the
passenger compartment).
•In case of transmission slippage, NEVER remotely start the
engine if you or someone else is directly behind or in front of
the vehicle.
5
Your 4-button/12-channel remote controls
The 4-button/12-channel remote controls are ultra-sophisticated miniature radio
transmitters powered by a tiny 12-volt battery. Range is up to 300 feet. A weak remote
control battery will reduce range, as will electrical and radio interference. You will
use your remote control to remotely start the engine, lock and unlock the doors, activate
AutoStart features, and command options such as a remote trunk release, headlight
activation, power window/sunroof closure and/or electric garage door interface.
How to use your key chain re mote con trol
Your remote control can individually
command up to 12 different system
functions and options. It’s like having a
TV with 12 channels. You change
channels (functions) with your keychain
remote control. But instead of putting 12
buttons on the remote control, we made it
easy: First, the button you use the most —
button 1 to lock and unlock the doors — is
larger than the others. Buttons 2, 3 and 4 are
the smaller buttons to the right, below and left of button 1. The LevelShift button on the
side of the remote control allows you to select channels 5–12:
To trans mit ei ther chan nel 1, 2, 3 or 4: Just press either button 1, 2, 3 or 4. For
instance, to transmit channel 3, press button 3. While you transmit, the remote
control’s LED indicator will blink once every second: this indicates level 1.
To trans mit ei ther chan nel 5, 6, 7 or 8: Press the LevelShift button once. This
shifts buttons 1–4 to level 2 (channels 5–8). Then press the desired button
within the next 7 seconds. For instance, to transmit channel 5, press the
LevelShift button once, then press button 1. While you transmit, you’ll notice
that the LED indicator blinks twice, pauses, blinks twice, etc.: this indicates
level 2.
To trans mit chan nel 9, 10, 11 or 12:Press LevelShift twice. This shifts buttons
1–4 to level 3 (channels 9–12). Then press the corresponding button within the
next 7 seconds. For instance, to transmit channel 10, press the LevelShift button
twice, then press button 2. While you transmit, you’ll notice that the LED
blinks three times, pauses, blinks three times, etc.: this indicates level 3.
NOTE: One sec ond af ter you stop trans mit ting level 2 or level 3 (chan nels 5–12),
the re mote con trol auto mati cally re turns to level 1 (chan nels 1–4). Chan nels
5–12 can be used to ac ti vate your ga rage door opener(s) via the op tional Clif ford ga rage door in ter face and/or Clif ford sys tem(s) on your other car(s).
6
How to remotely lock/unlock the doors
To lock all the vehicle doors, press button 1 once. All the following will occur:
•The doors will lock.
• As confirmation from a distance, you will see two flashes of the vehicle’s
parking lights.
• The LED on the system’s PlainView switch will flash repeatedly.
To unlock the doors, press button 1 again:
•The doors will unlock.
•You will see one flash of the vehicle’s parking lights.
• The PlainView switch LED will turn off.
•The interior courtesy light(s) will turn on an stay on for 30 seconds or until
you turn on the ignition and press the brake, whichever occurs first.
How to remotely start/shutdown the engine
WARNING: Always exercise caution and common sense when using the Smart
Remote Starter III. Never remotely start the engine or engage one or both AutoStart
features when the vehicle is parked in an enclosed area without adequate
ventilation.
WARNING: Never allow children to play with the remote control.
Whenever you remotely start the engine, the Smart Remote Starter III rapidly makes
a series of safety checks before attempting to crank the starter motor. It will:
•Verify that the engine or ignition switch is not already on.
•Verify that the transmission is in the PARK position.
•Verify that the engine is not overheated.
•Verify that no one is in the vehicle pressing the brake pedal.
•Verify that the hood is closed.
To remotely start the engine, press button 2. All of the following will occur:
•You will see two flashes of the vehicle’s parking lights to confirm that the
startup process has been initiated. (NOTE: Four flashes indicate a fault
condition, e.g., the hood is open).
•The engine and all preset accessories (air conditioner, heater, defroster,
etc.) will start and run.
•While the engine idles, the parking lights will be illuminated for on-going
visual confirmation.
When the engine is running under the control of your Smart Remote Starter III, you may, if
you wish, shut down the engine by again pressing button 2.
7
Diesel compatibility
If your vehicle has a diesel engine, your Smart Remote Starter III will activate the
engine’s glowplugs for 20 seconds before actually starting the engine.
To drive the vehicle
1.Unlock the doors by pressing button 1 on the remote control. The parking lights
will blink once and the interior lights will turn on.
2. Enter the vehicle and close the door, but do not press the brake pedal nor move
the transmission out of park.
3. Insert your key and turn the ignition switch to its “ON” position (don’t worry if
you turn the switch all the way to the “START” position; the system’s
StarterGuard feature will prevent you from accidentally grinding the starter
motor while the engine is running under the Smart Remote Starter III’s control).
4. Press the brake pedal. The interior lights will turn off. The system is now
disengaged and your vehicle will operate as usual.
NOTE: As an anti- theft meas ure, if some one presses the brake pedal or moves
the trans mis sion out of park be fore
tion, the Smart Re mote Starter III will im me di ately shut down the en gine.
turn ing the ig ni tion switch to the “ON” po si -
ShortStop
This is a great feature when you need to make a stop at a convenience store or to
make a quick delivery. Rather than shutting down the engine and then restarting it a
few moments later, the ShortStop feature allows you to remove your car keys from
the ignition switch without shutting down the engine. You may then exit and
remotely lock the doors while the engine continues to idle. To use the ShortStop
feature, simply perform the following steps:
1. Park the vehicle being sure to place the transmission in its park position and set
the hand brake.
2. Make sure you are not touching the brake pedal, then press button 2 on the
remote control.
3. You may now turn the ignition off and remove your keys without shutting down
the engine.
4. Exit the vehicle and lock the doors with button 1 on the remote control. The
engine will continue to idle under the control of your Smart Remote Starter III
for up to 30 minutes.
5. When you have completed your errand, just use the normal procedure noted in
the To drive the vehicle section on page 8.
8
Interfacing with factory theft deterrent devices
If your vehicle has a factory-installed theft deterrent device, the Smart Remote
Starter III can make it a full-fledged remote controlled car alarm, arming the device
every time you remotely lock the doors and disarming every time you remotely
unlock. Ask your system installer for details.
AutoLock and AutoUnLock (user-selectable)
For your safety and that of your passengers, the doors automatically lock when you
begin driving at about 15-20mph, and automatically unlock when you turn the ignition
off. To suit your preferences, you may turn off either or both the AutoLock and/or
AutoUnLock features. There are four possibilities: AutoLock “on” while
AutoUnLock is “off,” or vice-versa. The other two combinations are both
AutoLock and AutoUnLock “on” or both “off.” As set from the factory, both
features are on. To change the status of one or both features, see the User-selectable
features section on page 13.
Fault-proof starter Interrupt
When you remotely lock the doors, your Smart Remote Starter III engages its starter
interrupt circuit that prevents a thief from cranking the engine’s starter even if he
has a duplicate of your car key. Whenever you see the LED flashing on the system’s
PlainView switch, the starter interrupt is engaged and protecting your vehicle.
AutoActivation of the starter interrupt (user-selectable)
Smart Remote Starter III will protect your vehicle even if you forget to remotely
lock the doors (and thus activate the starter interrupt). Thirty seconds after you park
your car, exit and shut all the doors, the Smart Remote Starter III will automatically
(“passively”) activate the starter interrupt (if a door is re-opened during the
30-second countdown, the countdown will resume from the start once all doors are
closed). To provide visual confirmation, the system will flash the dashboard LED
twice 5 seconds after you close the doors to signal the start of the 30-second
countdown. To clear the starter interrupt, just press button 1 on your remote control.
If you prefer, you may turn off the starter interrupt autoactivation feature (see
User-selectable features on page 13). Also see the UltraSecure coded valet mode
section on page 10 for information on temporarily overriding autoactivation.
AutoActivation of the door locks (user-selectable)
If you wish, you may set the system to automatically lock the doors every time it
AutoActivates the starter interrupt. To ensure that you can’t accidentally lock your
key and remote inside the vehicle, this feature is factory set off. To enable this
feature, see the User-selectable features section on page 13.
9
Ul traSe cure™ coded valet mode
Your secret valet code
In seconds, thieves can disable all non-Clifford starter interrupt systems and alarms by
hotwiring the ignition and flicking an easy to find “hidden” valet switch. Your Smart
Remote Starter III has safeguards that absolutely ensure that a thief cannot enable the
valet mode as a way of “turning off” your system’s starter interrupt. How? To enable
valet mode, the driver must first enter a secret valet code on the PlainView switch. Your
code will be a 1-to-3-digit number of your choosing. Each digit can be any number from 1
to 9, (i.e. the code can be any number between 1 and 999, except those that contain a
zero). Whenever the system is put in valet mode, it overrides autoactivation of the starter
interrupt (see page 9). At various times, you will need to enable valet mode, such as
when having your car serviced, washed or parked by a valet.
NOTE: If you tem po rar ily lose the use of your re mote con trols, you can over ride
the sys tem’s starter in ter rupt by ena bling valet mode.
Your factory- set valet code is the sin gle digit “2.”
Definitions
Digit: A digit is defined as any number from 1 to 9, inclusive.
Valet code: A valet code may be 1 to 3 digits:
A one-digit code=X=any number between 1-9
A two-digit code=XY=any number between 11-99 (excluding those with zeros)
A three-digit code=XYZ=any number between 111-999 (excluding those with zeros)
Re mem ber, no code can have a zero.
Plain View switch:A rocker switch mounted on the dashboard or console. The
switch has three positions: 1.) Latched 2.) Center 3.) Spring-loaded
momentary. When you press the latched side, the switch remains in its
pressed position. When you press the momentary side, the switch bounces
back to the center position.
En ter ing a digit: To enter a digit, you tap (press and release) on the
momentary side of the PlainView switch the number of times corresponding
to the numeral of the digit to be entered, followed by pressing to the latched
side, then returning the switch to its center position.
En ter ing a code: If your code has only one digit, enter the code as described
in “Entering a digit.” If your code has more than one digit, just repeat the
above for each digit of your code.
10
To en able valet mode
1.Turn the ignition switch to its “ON” position or start the engine.
2. Enter your secret valet code on the PlainView switch, then return the switch to its
center position.
3. You now have 5 seconds to press the latched position to enter valet mode. The
LED on the PlainView switch will glow continually for on-going visual
confirmation of valet mode.
To exit valet mode
1.Turn the ignition switch to its “ON” position or start the engine.
2. Flick the switch back to its center position. The LED on the switch will turn off
to confirm that the system is now in its normal operating mode.
Setting your own secret valet code
Since all Clifford systems have the same factory-set code, it is highly advisable that
you set your own valet code. You may choose any 1-, 2-, or 3-digit code that does
not have any zeros. You may also change your valet code whenever you want.
Simply write down the 1-to-3 digit code you wish to use (remember, no zeros in the
code), then refer to the User-selectable features section on page 13.
Ex am ple
Let’s say you want to set your valet code to 31. To do so, you would do the following:
1. From the table of User-selectable features on page 13, you would note that the
“set new valet code” feature number 11.
2. Enter program mode by turning on the ignition, then enter your current valet
code (if still the factory default, this would be momentary, momentary, latched).
3. Select feature number 11 by tapping the momentary side of the switch 11 times.
To help you count, the switch’s LED will, after the first 3 taps, blink once each
time you tap the momentary side. Therefore, you’ll see a total of 8 blinks for
feature 11.
4. Immediately flip the switch to the latched position.
5.Enter you new code. To enter 31 as your new code, you would press the switch in
this manner: momentary, momentary, momentary, latched, momentary, latched,
center.
6. Wait 3 seconds until you see two LED blinks, indicating the new code has been
accepted.
7. Turn off the ignition to exit program mode.
8. VERY IMPORTANT: You must immediately test your new secret valet
code: Turn on the ignition, enter your new code, then flip the switch to its
latched position. The LED on the switch will illuminate. If it does not, the new code
you programmed and the one you just entered do not match. In such a case, the
system will revert to the previous code.
11
The AutoStart features
Your Smart Remote Starter III has two AutoStart features:
AutoStart Battery Mode: This is an especially valuable feature when you need to leave
your vehicle parked for an extended period of time. If engaged, the system will
automatically monitor the voltage level of the vehicle battery while you are away. If the
voltage drops below a preset level, the system will automatically start the engine and
recharge the battery (to conserve battery power, the Smart Remote Starter III will not
activate the parking lights nor any preset accessories in this mode). Likewise, the system
automatically shuts down the engine once the battery is properly charged or after 30
minutes, whichever occurs first. If needed, the process will repeat every eight hours until
the battery is properly charged. AutoStart Battery Mode is automatically canceled as soon
as you drive your car.
AutoStart Temperature Mode: Whenever you wish, you may set your Smart Remote
Starter III to AutoStart the vehicle if the engine temperature drops below 15°F (-9°C). The
system will idle the engine for 30 minutes or until you enter and drive, whichever occurs
first. AutoStart Temperature Mode is automatically canceled as soon as you drive your car.
You can activate either of the AutoStart features via the programming procedure
(see the User-selectable features section on page 13). Or, for even greater ease, just
press remote control button 4 to remotely activate both AutoStart features (two flashes
of the parking lights will confirm remote activation of the AutoStart features).
Optional remote headlight activation and/or remote trunk release
Button 3 on your remote control can command two different options: one while the
system’s starter interrupt is engaged and another while it is disengaged.
If you have the optional remote headlight activation feature installed, a single
press of button 3 while the system’s starter interrupt is engaged (i.e., the LED is
flashing) will activate the system’s built-in timer to illuminate the headlights for
any duration of your choice between 1 second and two minutes. To change the
headlight duration, see User-selectable features on page 13.
If you have the optional remote trunk release feature, a press of button 3 while the
system’s starter interrupt is disengaged (LED is off) will pop the trunk. For safety
and security reasons, the button 3 will not pop the trunk if the engine is running to
ensure against accidental activation while driving.
Optional remote controlled window/sunroof closure
On certain vehicles, including several models of BMW, Mercedes Benz, Volkswagen
and Jaguar, the Smart Remote Starter III can be wired to automatically close all the
power windows/sunroof every time you remotely lock the doors. If you have this
feature, do not change the user-selectable headlight duration. Doing so may cause
damage to your vehicle’s window/sunroof motors.
12
User- selectable fea tures
Your Smart Remote Starter III system comes from the factory with all of its features
pre-programmed as noted in the following table. No programming is required, but if you
wish to change any of the settings, just use the procedure below. To restore the feature to
its factory setting, just repeat the procedure:
1. Select the feature you wish from the table. Note the number of momentary taps.
2. Turn your vehicle’s ignition switch to its “ON” position.
3. Enter your valet code as noted on page 10-11, then immediately tap and release
the momentary side of the switch the number of times corresponding to the
feature you wish to change. Beginning with the 4th tap, the LED will blink each
time you tap thereafter to help you count (e.g., 5 blinks for feature 8; 9 blinks for
feature 12, etc.).
a.If noted, perform the “Secondary action.”
b. If noted, wait for the “Completion confirmation.”
4. Turn the ignition off. Repeat steps 1-4 for any other feature you wish to program.
Feature
Battery Mode
AutoStart
Temperature Mode
AutoStart
AutoUnLock ON 6 —
AutoLock ON 7 —
AutoActivation
of starter interrupt
AutoActivation
of door locks
Factory
setting
# of
Secondary action
taps
OFF 4 — 2 flashes=ON Change from OFF to ON
OFF 5 — 2 flashes=ON Change from OFF to ON
ON 8 —
OFF 9 —
Completion
confirmation
1 flash=OFF
2 flashes=ON
1 flash=OFF
2 flashes=ON
1 flash=OFF
2 flashes=ON
1 flash=OFF
2 flashes=ON
Result
Change from OFF to ON
or vice-versa
Change from OFF to ON
or vice-versa
Change from OFF to ON
or vice-versa
Change from OFF to ON
or vice-versa
Feature 10 requires installer programming. Do not change the status of feature 10.
Set new valet code 2 11
Add a
new remote control
— 12
See Setting your own secret valet code on page 11.
Press button 1 on the
new remote control
2 flashes
New remote control has
been added
Features 13-14 require installer programming. Do not change the status of feature 13 or 14.
Set headlight duration ✱
30 sec. 15
After 15th tap, start
counting. Turn ignition off
after desired duration
—
New headlight duration
has been set
✱ WARNING: DO NOT change the headlight duration if the system automatically
closes the power windows every time you remotely lock the doors. Doing so may
damage your vehicle’s window/sunroof motors.
13
Adding new remote controls
For other drivers in your family, or if you wish to control Clifford systems on your
other cars with the same remote control, you can buy additional remote controls
from any Clifford Dealer (or call our Customer Service Department at
800-824-3208) and program them into the system yourself. Each Smart Remote
Starter III will respond to as many as four 12-channel remote controls. To add a
new remote control to the system, use the procedure noted in the User-selectable
features section on page 13.
How to erase the codes of lost or stolen remote controls
If one of your remote controls is ever lost or stolen, you can erase its digital codes
from the system memory to make sure that the missing remote control can never be
used to control your system. To do so, simply program each remaining and/or
replacement remote control as noted in the Adding new remote controls section
above for a total of four times (e.g., if you have just one remote, program it four
times; for two remotes, program each twice; for three remotes, program one twice).
Smart Re mote Starter III is cov ered by one or more of the fol low ing
Clif ford Elec tron ics pat ents: 4,158,874; 4,233,642; 4,327,444; 4,383,242;
4,430,685; 4,845,464; 4,887,064; 4,890,108; 4,922,224; 4,997,053; 5,081,667;
5,146,215; 5,157,375; 5,467,070; 5,650,744 and other pat ents pend ing.
© Copy right Clif ford Elec tron ics, Inc., 1998 31- 150D/S RS3OM/398
Loading...