Clifford GP1000T Owners Guide

GP1000T
OOwwnneerrss GGuuiiddee
i
© 2005 directed electronics, inc. all rights reserved
limited lifetime consumer warranty
Directed Electronics, Inc. ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the life­time of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorised Directed dealer; the unit will be professionally rein­stalled in the vehicle in which it was originally installed by an authorised Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone num­ber and address; the authorised dealers name, telephone number and address; complete prod­uct description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including with­out limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-trans­ferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what con­stitutes excessive damage and may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CON­NECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORISED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE VEHICLE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITA­TION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOUR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUN­TY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORISED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCI­DENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL
ii
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CON­TROL MODULE AS DESCRIBED ABOVE. Some territories do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential dam­ages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State or country to country.
Directed security systems, including this unit, are deterrents against possible theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft of the vehicle, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without lim­itation, liability for theft, damage and/or vandalism. Directed does not and has not authorised any person or entity to create for it any other obligation, promise, duty or obligation in con­nection with this security system.
Make sure you have all of the following information from your dealer:
A clear copy of the sales receipt and installation certificate, showing the following:
z
Date of purchase
z
Your full name and address
z
Authorised dealer's company name and address
z
Type of alarm installed
z
Year, make, model and colour of the vehicle
z
Vehicle registration number
z
Vehicle identification number
z
All security options installed on vehicle
trademarks and copyrights
Bitwriter®, Clifford®, Code-Hopping®, Directed®, Doubleguard®, ESP®, FailSafe®, Ghost Switch™, Learn Routine
, Nite-Lite®, Nuisance Prevention®, Revenger®, Silent Mode™, Soft Chirp®, Stealth
Coding
, Stinger®, Valet®, Vehicle Recovery SystemTM, VRS®, and Warn Away®are all Trademarks
or Registered Trademarks of Directed Electronics, Inc.
1
© 2005 directed electronics, inc. all rights reserved
limited lifetime consumer . . . . . . .
warranty . . . . . . . . . . . . . . . . . . . . .i
trademarks and copyrights . . . . .ii
table of contents . . . . . . . . . . . . .1
what is included . . . . . . . . . . . . . .2
important information . . . . . . . . .2
your warranty . . . . . . . . . . . . .3
remote configurations . . . . . . . . .4
standard configuration for in-key
2-button remote . . . . . . . . . . .5
standard configuration for . . . . .
3-button remote . . . . . . . . . . .5
using your system . . . . . . . . . . . . .6
arming . . . . . . . . . . . . . . . . . . .6
disarming . . . . . . . . . . . . . . . . .8
disarming without a remote . . .8
auto-immobilisation . . . . . . . . .9
remote siren silencing . . . . . . .9
remote chirp muting . . . . . . . . .
(3-button remote only) . . . . . .10
remote sensor disable . . . . . .11
remote start sensor bypass . . .11
auxiliary channel bypass . . . . .12
panic mode . . . . . . . . . . . . . .12
valet mode . . . . . . . . . . . . . . .12
remote valet mode . . . . . . . . .13
instant auto-arming bypass . .13
low battery warning . . . . . . .14
automatic noise abatement . .14
multiple event total recall . . . .14
battery back-up siren . . . . . . . . .14
diagnostics . . . . . . . . . . . . . . . . . .15
arming diagnostics . . . . . . . . .15
disarming diagnostics . . . . . . .16
arm/disarm diagnostic chart . .17
table of zones . . . . . . . . . . . .18
high frequency . . . . . . . . . . . . . .19
smart power up II . . . . . . . . . . . .19
power saver mode . . . . . . . . . . .19
system sensors and adjustments 20
programming options . . . . . . . .20
manual programming . . . . . . . .
instructions . . . . . . . . . . . . . .22
user selectable features . . . . .24
user selectable features descrip-
tions - column one . . . . . . . . .24
user selectable features . . . . . . .
descriptions - column two . . .25
user selectable features . . . . . . .
descriptions - column three . .26
programming notes . . . . . . . .28
pin programming . . . . . . . . . .30
glossary of terms . . . . . . . . . . . . .32
security & convenience . . . . . . . . .
expansions . . . . . . . . . . . . . . . . . .33
health check . . . . . . . . . . . . . . . .34
table of contents
2
what is included
z
One control module/siren with built-in Tilt sensor
z
One 24-pin main wiring harness
z
One Mini-Blue status LED
z
One 2-button coded Valet switch
z
One in-key 2-button remote
z
One 3-button remote
z
Two Clifford®G5 decal’s
z
Presentation envelope
z
This Owner’s Guide
z
Quick Reference Card
z
Warranty Card
important information
Congratulations on the purchase of your state-of-the-art motorcycle
security system. It has been designed to provide years of trouble-free
operation. This system must be installed by an authorised dealer.
Installation of this product by anyone other than an authorised dealer
voids the warranty. As verification of authorisation, all authorised deal-
ers are provided with preprinted dealer certificates.
In order to maximize the use of this system, please review this owner's
guide carefully prior to using your system. You can print additional or
replacement copies of this owner’s guide by accessing the Clifford
®
website at www.clifford.com.
3
© 2005 directed electronics, inc. all rights reserved
system maintenance
The system requires no specific maintenance. The batteries in your
remotes will last approximately one year under normal use. Your 3-but-
ton remote is powered by a miniature 3V lithium battery (CR2032) Your
in-key 2-button remote is powered by a 12V miniature battery (type
27A).
your warranty
It is necessary to retain your sales receipt, which reflects that the prod-
uct was installed by an authorised dealer. For full details regarding your
warranty coverage, please refer to the consumer warranty section of
this guide.
nnoottee::
Making changes to the existing system will invalidate the certifi-
cate of installation.
nnoottee::
The Installation Certificate must be completed by your installer at the authorised dealer. Other than the remote controls, this system has no user-serviceable parts. Your authorised dealer can correct any system wiring problems and, if needed, can return any malfunctioning compo­nent to Directed Electronics for repair/replacement under the terms of the Limited Lifetime Warranty printed at the beginning of this guide.
nnoottee::
Your system MUST be installed by an Authorised dealer in accor-
dance with the instructions we supply them. The Clifford
®
GP1000T system is designed to be installed on any 12-volt, negative earth motor­cycle or moped.
4
remote configurations
The GP1000T system has an in-key 2-button remote control and a 3-
button remote control. Two additional Clifford®G5 remote controls can
be added.
A
IN-KEY 2-BUTTON REMOTE CONTROL
FRONT REAR
LED
ACCESSORY
RM/DISARM/PANIC
3-BUTTON REMOTE CONTROL
SILENT ARM/DISARM
ARM/DISARM/PANIC
ACCESSORY
5
© 2005 directed electronics, inc. all rights reserved
remote functions
This system uses computer-based code learning to learn the remote buttons. This makes it possible to assign any remote button to any sys­tem function. The remotes initially come programmed with standard configuration. The buttons in all of the instructions in this manual cor­respond to a standard configuration remote.
standard configuration for in-key 2-button remote
Button
The arming, disarming, and panic functions are controlled by this button.
Button
An optional accessory convenience or expansion function that you have
added to your system can be activated by pressing this button.
and Buttons
When pressed together, these buttons disable the on-board control
module tilt sensor and any optionally installed sensors.
standard configuration for 3-button remote
Button
The arming, disarming, and panic functions are controlled by this button.
6
Button
An optional accessory convenience or expansion function that you have
added to your system can be activated by pressing this button.
Button
Silent arm and disarm is controlled by this button.
and Buttons
When pressed together, these buttons disable the on-board control
module tilt sensor and any optionally installed sensors.
and Buttons
Remotely enters or exits Valet.
using your system
figured, the icons on your remote buttons may not correspond to the
indicated functions.
arming
You can activate, or arm, the system by pressing on your remote
for one second. When the system arms, you will hear two short siren
sounds, or chirps, and see the indicators flash twice. The LED will begin
to flash steadily.
7
© 2005 directed electronics, inc. all rights reserved
While the system is armed, the LED status indicator will flash approxi-
mately once per second showing that the system is actively protecting
your vehicle. If you hear more than two chirps when arming, refer to
the Diagnostics section of this guide. These extra chirps confirm a mal-
function autobypass.
The security system also can be programmed to arm itself
automatically without a remote (called passive arming). If the system is
programmed for passive arming, it will automatically arm 30-seconds
after the ignition is turned off. Whenever the system is in its 30-second
passive-arming countdown, the siren will chirp twice and the lights will
flash twice five seconds after countdown has commenced. The system
is not actually armed at that point. The system arms after the 30-sec-
ond countdown has elapsed, but the siren will not chirp. The early
chirps provide you with a 25-second warning prior to arming.
When armed, your vehicle is protected as follows:
z
The LED will flash as a visible theft deterrent.
z
If the tilt sensor detects the motorcycle is being moved in an attempt to steal it, the system will immediately trigger the siren and flash the indicator lights.
This sensor is capable of independently learning the bike’s ini­tial angles of vertical and horizontal inclination each time it is parked, ensuring the most accurate tilt (vertical and horizon­tal) sensing possible.
z
If a protected switch is opened, the system will immediately trigger the siren and flash the indicator lights.
z
The immobiliser prevents the motorcycle’s engine from starting.
nnoottee::
If the protected switch (or other optional protected area) is open, the system will not passively arm. Additionally, each time a protected entry is triggered during the arming countdown, the 30-second count­down starts over.
8
disarming
To disarm the system, press . You will hear a chirp and the indica-
tor lights will flash once. If the siren chirps three times when disarming,
refer to the Diagnostics section of this guide. This is called Tamper Alert.
If the siren is active (sounding) when the system is disarmed you will hear
two or four chirps but the system is not disarmed. (Refer to the Remote
Siren Silencing section of this guide.) However, if the alarm completes the
full trigger cycle when disarmed you will hear three chirps.
disarming without a remote
This feature allows you to disarm the system without the remote should
it be lost, damaged, or disabled. In order to disarm without a remote,
you must have the motorcycle’s ignition key, know where the Valet
switch is located, and have the PIN code. Be sure to check with the
installer for the location of the Valet switch.
Turn the ignition On and then enter the PIN code as given in the fol-
lowing example to disarm without a remote.
1. Find the preset PIN code noted on the back of this manual.
FOR EXAMPLE: To disarm first enter a PIN code of 4301.
2. Turn the ignition On.
3. Press four times.
4. Then once. This enters the digit 4.
5. Then three times.
6. Then once. This enters the digit 3.
9
© 2005 directed electronics, inc. all rights reserved
7. Then once. This enters a 0 as there was not a previous digit entered with .
8. Then once.
9. Then once. This enters the final digit 1.
10. Then button once to disarm without a remote.
auto-immobilisation
Immobiliser circuits automatically activate after 30-seconds.
Auto-immobilisation sequence:
1. Turn ignition off or disarm alarm.
2. After 30-seconds the systems Immobilisation circuits activate and engage the starter and engine interrupts.
3. LED flashes at ½ normal speed.
Disarm the system when immobilised:
Use one of the following methods to turn off auto-immobilisation.
z
Turn ignition on and press the button of the trans­mitter.
z
Arm the alarm and then disarm the alarm.
z
Turn the ignition on and enter the system Valet/PIN code.
remote siren silencing
Remote siren silencing is a feature that makes it possible to silence and
reset the system when it is triggering without disarming the system. If
the system is triggered and the siren is sounding, press on the
10
remote to stop the trigger and return the unit to the armed state. The
system will not disarm, but rather reset. This prevents you from dis-
abling the system should you wish to silence it without visually check-
ing the vehicle. After resetting the system, press again to disarm
the system.
When you remote siren silence, the siren will either chirp 2 or 4 times.
2-chirps indicate that the system is still armed, but the trig­ger that caused the alarm is no longer active.
4-chirps indicate that the system is still armed, but the trig­ger that caused the alarm is still active.
NNOOTTEE::
If 4-chirps sound the input that caused the alarm trigger will be bypassed
until the system is fully disarmed and armed again, or the alarm trigger is removed.
remote chirp muting (3-button remote only)
To temporarily turn off the arm or disarm chirps, use remote chirp mut-
ing. Simply press on the remote (3-button remote only), and
the confirmation chirp(s) will be eliminated for that one operation only.
The indicator lights will flash to confirm the arm/disarm command. If
you want the arm/disarm chirps turned off permanently, please refer to
the User-Selectable Features section of this guide.
11
© 2005 directed electronics, inc. all rights reserved
remote sensor disable
dure listed below.
1. Arm the system.
2. Using the remote press and simultaneously.
3. The indicators will flash four times; all Warn Away
®
zones of optionally installed sensors are now bypassed (zones two and three).
4. Using the remote press and simultaneously again.
5. The lights will flash four more times; the sensor Warn Away
®
and full trigger zones are now bypassed (zones one, two, and three). To bypass the system tilt sensor press the sensor disable buttons twice.
6. The sensor zones will reset when disarmed.
remote start sensor bypass
When the system sees a command to remote start the vehicle, it
bypasses sensor zones and will continue to bypass these zones until the
remote start shuts down.
nnoottee::
Sensor disable can be performed at any time after the alarm has
been armed.
12
auxiliary channel bypass
All alarm sensor inputs will be bypassed while a pulsed or timed auxil-
iary output is active.
panic mode
triggering the system with your remote! Just press for two sec-
onds to enter Panic Mode. The siren will sound and the indicator lights
will flash for the 30-seconds. To stop Panic Mode at any time press
on the remote again.
valet mode
You can prevent your security system from automatically arming by
using Valet Mode. This is very useful when washing the motorcycle for
example. In Valet Mode, the security system will not arm, even with the
remote, but any accessory functions will continue to work normally.
To enter Valet Mode:
1. Turn the ignition On.
2. Enter the PIN code as described in the Disarming Without a Remote section.
3. After the last digit continue to hold for three seconds.
The LED status indicator will light steadily if you are entering Valet Mode.
13
© 2005 directed electronics, inc. all rights reserved
To exit Valet Mode:
1. Turn the ignition On, the system will exit Valet
®
mode auto-
matically.
remote valet mode
The operations described in this section refer to remote buttons.
Remember, the buttons used in all the instructions in this guide corre-
spond to the Standard Configuration for the 3-button remote. This
may not be how your remote is set up.
To enter Valet Mode, press and simultaneously. The LED
status indicator will illuminate continuously if you are entering Valet
Mode, or will turn off if you are exiting Valet Mode.
instant auto-arming bypass
This will bypass the auto arm feature once only.
1. With the key, turn the ignition on, then off within two seconds.
2. The siren will chirp once to confirm auto arming bypass.
3. The system will not auto arm.
sory output when using the remote to arm the system.
nnoottee::
The system will revert to normal auto arming when the system sees the ignition on for at least three seconds and then turned off, or the system is armed and disarmed with the remote.
14
low battery warning
When the transmitter battery is low, the siren will generate 5 rapid
chirps when the alarm is disarmed.
automatic noise abatement
Alarm sounding is limited to ten 30-second siren duration cycles to
meet European criteria and local noise pollution laws.
multiple event total recall
This will report the last eight system triggers in reverse chronological
order.
1. Press and hold of the Valet switch.
2. While still holding , arm and disarm the system, then release the button.
3. The LED will start to flash to indicate the most recent trigger and proceed down to the eighth trigger. For more informa­tion, please refer to the Table of Zones section of this guide.
battery back-up siren
The built-in battery back-up siren protects the system if a thief discon-
nects power and/or cuts or tampers with the power supply wires while
the system is armed. If system power is lost the siren will sound for five
minutes and then reset.
15
© 2005 directed electronics, inc. all rights reserved
diagnostics
The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensors and prevents them from dis­abling the entire system. The microprocessor will also record and report any triggers that occurred during your absence.
arming diagnostics
If the system is armed while an input is active (sensor triggering, etc.)
the unit will chirp four times when arming or twice and then four more
times five seconds, or ten seconds later. This is called Bypass Notification.
Refer to the Arm/Disarm Diagnostic Chart for bypass notification details.
You are able to see exactly which zone is causing the bypass notification by
disarming the system and turning the ignition on. The zone will be report-
ed by flashing the active zone 5-times. See the Table Of Zones.
16
The security system will ignore the input that was active when the sys-
tem was armed, until the input goes away. 3-seconds later the system
will monitor that input normally. For example, if the protective switch
is active, you will hear four Bypass Notification chirps (the protective
switch is bypassed from the alarm system). Once the protective switch
is reset, then 3-seconds later the system resumes normal monitoring of
this switch.
disarming diagnostics
Extra disarm chirps are the Tamper Alert. If three chirps are heard when
disarming, the system was triggered in your absence. If three chirps are
heard, the LED status indicator will indicate which zone was triggered
(refer to the Arm/Disarm Diagnostic Chart and Table of Zones section).
The system will retain this information in its memory. Refer to the
Multiple Event Total Recall section of this guide.
17
© 2005 directed electronics, inc. all rights reserved
arm/disarm diagnostic chart
Refer to the table of zones to identify the last zone triggered.
Action No. of Chirps Description
Arm 2 System armed
Arm 4 System armed with a protection switch
active and bypassed (zones 4 and 5)
Arm 2 (5-sec. pause) 4 System armed with tilt sensor
active and bypassed (zone 1)
Arm 2 (10 sec. pause) 4 System armed with auxiliary sensor 1 or
2 active and bypassed (zones 2, 3)
Disarm 1 System disarmed
Disarm 3 System disarmed with tamper alert
Disarm 2 System silenced, but still armed, but
input that triggered system is no longer active.
Disarm 4 System silenced, but still armed, and
input that triggered the system is still active but bypassed.
Disarm 5 System disarmed with a remote control
that has low battery voltage.
18
table of zones
The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If a Warning Zone response is triggered, the LED will not report it.
anti-code grabbing (ACG)
This unit features Anti-Code Grabbing (ACG) with Random Code
Encryption. This means the receiver and remotes each use a mathemati-
cal formula called an algorithm to change their code each time the
remote is used. This technology has been developed to increase the secu-
rity of the unit. The control unit knows what the next codes should be.
Zone - Number Dealer-Installed of LED Flashes Description Options
1 Tilt Sensor
(Built-in Tilt Sensor)
2 Auxiliary sensor 1
input
3 Auxiliary sensor 2
input
4 Normally Closed
input (from protective switch)
5 Optional switch input
6 Ignition Input
7 12 V Power interruptions
19
© 2005 directed electronics, inc. all rights reserved
high frequency
Your system transmits and receives at 433 MHz. This provides a cleaner
spectrum with less interference and a more stable signal.
smart power up II
This security system will store its current state to non-volatile memory.
If power is lost and then reconnected the system will recall the stored
state from memory. This means if the unit is in Valet Mode and the bat-
tery is disconnected for any reason, such as servicing the car, when the
battery is reconnected the unit will still be in Valet Mode. This applies
Valet Mode.
power saver mode
z
When in Valet mode, the LED will turn off 1-hour after enter­ing Valet mode.
z
After 24 hours in the armed state, the LED will decrease the flash rate to 1/2 the normal rate; after 48 hours it will decrease to 1/4
the normal rate.
20
z
After 96 hours of no activity (arm, disarm, or alarm trigger) the alarm enters sleep mode. The alarms receiver, and LED turn off to save as much battery power as possible. The system is drawing next to no current in this mode.
To exit sleep mode turn the ignition on and the siren will chirp 10 times (5-seconds) before the siren sounds. Disarm the system with the remote or by entering the PIN code with the Valet switch.
If any other input is activated when in sleep mode, the system will wake up and trigger the alarm immediately.
system sensors and adjustments
Your system was installed with an integral Tilt sensor. Optional sensors
such as the 504C Dual-Zone Shock sensor or 508D Dual-Zone Proximity
sensor may also have been installed.
For adjustments to all sensors/options, please return your motorcycle to
the installing Clifford
®
dealer.
programming options
Programming options control what your system does during normal
operation, and require few or no additional parts. However, some may
require additional installation labour.
21
© 2005 directed electronics, inc. all rights reserved
Following is a list of the program settings, with the factory settings in bold:
z
Autoarming on or autoarming off of the alarm : Automatic arming 30-seconds after ignition turned off.
z
Arming/disarming confirmation siren chirps off, loud or quiet. The siren arm/disarm chirps can be either full volume, 6 decibels quieter, or turned off completely.
z
Panic mode: on/off.
z
Set PIN code: Allows you to enter your own PIN code, over­writing the factory PIN code.
z
Siren tones: The output of the siren consists of six different tones in sequence. Any of these tones can be eliminated, result­ing in a unique, easily identifiable siren sound.
z
Remote Valet: on/off.
z
Reset settings to default (except for PIN code)
z
New remote learn features: Allows programming individual transmitter channels to custom configurations. Refer to User
Selectable Features Descriptions - Column Three.
z
Clear all Remotes: Removes all remote controls from memory.
22
manual programming instructions
It is a good idea to document changes by taking note of all feature
changes made in programming mode.
To enter the User Selectable Features programming:
1. Ignition on - Turn the ignition to the on/run position or start the engine.
2. Enter PIN - Your PIN code is noted on the back of this guide.
FOR EXAMPLE: To enter a PIN code of 4301—
Press four times,
then once. This enters the digit 4.
then three times,
then once. This enters the digit 3
and then once. This enters a 0 as there was not a previous digit entered with .
then once,
and then once. This enters the final digit 1.
3. Hold/Chirp/Release - After entering the PIN code, press and hold until a chirp is heard and the LED turns on, then release the button. You have now entered the feature selec­tion position of the User Selectable Features grid.
4. Column select - Press and release the same number of times as the desired column. After a pause the siren will chirp the same number of times as the selected column for confirmation (e.g. 3-chirps means column 3 of the features is selected).
5. Feature select - Press and release the same number of times as the desired row. The siren will chirp with each press. The feature can now be changed using the remote control.
23
© 2005 directed electronics, inc. all rights reserved
6. Feature change - Press the button on the remote. If the system chirps once, the feature has just turned off or switched to the first setting in the grid slot for this feature.; if the system chips twice, the feature has just turned on or switched to the second setting in the grid slot.
If the feature has more than two settings, continue pressing the on the remote to toggle through the settings (e.g. if the feature has 1 through 5 settings, the system will chirp 1 through 5 times for each setting selected). If you continue to press and release the remote the feature setting will wrap back around to the first setting again. (e.g. if the feature has 3 settings you will hear, 1 chirp, 2, chirps, 3 chirps, 1 chirp, 2 chirps, etc).
To advance to another feature in the same column, press
the same number of times as the desired feature with­in 60 seconds; to change a feature in a different column begin at step 5 by entering the column number first and then the feature select in step 6.
7. Exit programming - To exit programming mode turn the igni­tion off or wait 60 seconds without pressing the Valet
®
switch. The siren will chirp three times to indicate program­ming mode has been exited.
After you change a feature setting, the feature counter is reset to zero. Hence, to change another feature in the same column you must press the button the same number of times as indicated in the chart below.
nnoottee::
Refer to the Feature Descriptions sections of this guide for impor-
tant notes and descriptions of the system features and programming.
24
user selectable features
user selectable features descriptions - column one
add new remote (for 2-button in-key and 3-button remotes only)
z
Auto-learn new remote controls to the system (one at a time) in the standard button configuration. For more infor­mation, refer to Note #1 in Programming Notes section.
nnoottee::
OEM and Radar2 remotes cannot be AutoLearned. These remotes must be programmed using the functions 1 through 5, listed in column 3.
First Press
Then Press
Add new remote
(autolearn)
Auto arm
on/off
Chirps
off/loud/quiet
Panic
on/off
Not used
Not used
Set PIN code New remote learn
arm/disarm only
Select siren
sounds
Not used
Remote valet
on/off
Reset to default
(except transmitter
and PIN code)
Not used Clear all remotes
New remote learn
accessory output
New remote learn
silent mode
New remote learn
remote valet
New remote learn
sensor disable
from memory
25
© 2005 directed electronics, inc. all rights reserved
auto (passive) arm - on/off
z
On: When the system sees the ignition turn off, it will begin a 30-second countdown before arming itself. The count­down is indicated by the system LED rapid flashing. After the first five seconds, you will hear two chirps and the indicators will flash. The system will arm 25 seconds later.
z
Off: The transmitter must be used to arm the system.
chirps - off/loud/quiet
z
Off: Chirps will not sound when arming/disarming the sys­tem (with the exception of arm/disarm diagnostic chirps and programming chirps).
z
Loud: Chirps will sound when arming/disarming the system at full volume.
z
Quiet: Chirps will sound when arming/disarming the system but at a lower volume than normal (with the exception of arm/disarm diagnostic chirps and programming chirps).
panic - on/off
Allows the remote to activate Panic Mode. The siren will sound for 30
seconds.
z
On: The system will enter Panic Mode if the arm/disarm but­ton is pressed for more than 2 seconds.
z
Off: Panic Mode is disabled.
user selectable features descriptions - column two
set pin code
z
This feature allows you to change your personal PIN code. For more information, please refer to the PIN Programming section of this guide.
26
select siren sounds
This feature allows you to select which siren sounds will be played back
cedure to set this feature:
1. Enter the feature.
2. Press the button of the remote to begin the playing of siren sounds.
3. Siren will generate each sound for 5-seconds. There are 6 in total.
4. To add the sound press the button on the Valet switch while that sound is playing.
5. To delete the sound press the button on the Valet switch while that sound is playing.
nnoottee::
After selecting or deleting a sound the siren will immediately play the next
sound. If no sounds are selected by pressing the or button the system will remain in its previous setting.
remote valet on/off
This feature allows you to set remote Valet on or off.
reset to default
This feature allows you to restore the programming to factory defaults,
except for the PIN code and remote controls programmed into the system.
user selectable features descriptions - column three
The features in this column pertain to programming individual remote
channels in custom configurations. Following is an explanation of the
27
© 2005 directed electronics, inc. all rights reserved
features. To program specific functions to a different button, enter the
function you are programming after the chirp confirmation. Press the
button with which you wish to control that feature; the system will
chirp to confirm that it has learned the new button. Refer to Note #2
in Programming Notes section.
arm/disarm only
z
The remote control channel programmed into this feature will arm/disarm the system only.
accessory (-) output
z
The remote channel programmed into this feature will acti­vate the accessory output. Refer to Note #3 in Programming Notes section.
silent mode
TM
z
The remote channel programmed into this feature will arm/disarm the system, but the siren will not chirp.
remote valet on/off
z
The remote channel programmed into this feature will make the system enter/exit valet mode.
nnoottee::
When programming a remote control to custom configuration, a remote button must first be learned to the arm/disarm channel by press­ing the desired button once (one chirp), then again (two chirps). The rest of the features in this column can then be learned by pressing the desired button once. The siren will chirp the same number of times as the feature row as confirmation.
A remote button can only be learned to one designated feature. That is, if the lock/unlock button is programmed for armed/disarmed (fea­ture 1 in column 3), it cannot be programmed for another additional feature listed in column 3 of the User Selectable Features.
28
sensor disable
z
The remote button programmed for this feature will make the system bypass the sensors for one arming cycle only. On the next arming cycle, zones 1, 2, and 3 will be reinstated.
clear all remotes
z
This feature will erase all remote codes from the system memory. This feature is convenient for erasing any remotes that have been lost, stolen, or incorrectly programmed into the system.
z
After entering this feature press the button on a remote that is programmed to the system; the siren will chirp twice to indicate that all remotes have been erased from memory.
programming notes
Note #1: Adding a new remote in auto-learn configuration
z
Press the button of the remote control; the siren will chirp once.
z
Immediately press again; the siren will chirp twice to confirm the new remote has been programmed.
Note #2: Adding a new remote in custom-configuration
z
For the channel, transmit the channel of the new two, three, four, or five button remote that you want to con­trol that feature; the siren will then chirp once.
z
Immediately transmit the same channel again, the siren will chirp twice to confirm the remote channel has been pro­grammed.
29
© 2005 directed electronics, inc. all rights reserved
z
For the rest of the channels only one press of the button is required to learn, and the siren will chirp the same number of times as the feature row.
Note #3: Accessory Channel
z
The accessory channel output can be programmed to differ­ent types of output including a pulsed output that does not function when ignition is on or the system is armed, a pulsed output regardless of the ignition/armed state, a timed out­put, a latched output, a latched output that resets when the ignition is turned on and a Remote start output for connec­tion with a 561T remote starter*.
z
The accessory channel can also be programmed to auto-acti­vate with the arm command of the transmitter, the disarm command of the transmitter, or both. Consult your dealer for more options.
* Note: Not evaluated by Thatcham.
nnoottee::
When programming a new transmitter to custom configuration, an arm/disarm channel must first be programmed before programming the remaining channels.
30
pin programming
A PIN code can have one to four digits; each digit can be from 0-9.
Programming Procedure
1. Enter the feature location (column 2, row 1) in the user­selectable programming grid.
2. Immediately press and release of the Valet switch.
3. Select each digit by pressing 1-9 times, and then press
to enter the number into the system. To enter a zero,
press only.
To program a PIN code of 1032:
A. Press and release once and once. You will
hear one chirp.
B. Press and release once. You will not hear a chirp
after programming a zero.
C. Press and release three times, and then press
once. You will hear three chirps.
D. Press and release two times, and then press
once. You will hear two chirps.
4. Wait for two siren chirps after a five second pause or five seconds after the last digit has been entered if using less than four digit code number.
5. Turn off the ignition; the siren will chirp three times.
6. The programming mode is now exited.
nnoottee::
A PIN code cannot begin with a zero.
31
© 2005 directed electronics, inc. all rights reserved
PIN Code Confirmation Procedure
Begin this procedure within 15 seconds of finishing the programming
sequence or the new code will not be set.
1. Turn on the ignition.
2. Enter the new PIN code.
3. Press and hold for three seconds.
z
LED turns on: New PIN code is learned and program­ming is complete.
z
LED stays off: New PIN code is not learned and the sys­tem reverts to the old PIN code. Repeat the program­ming sequence.
32
glossary of terms
Control Unit:
The "brain" of your system hidden somewhere on the
motorcycle where it is difficult for a thief to access. It houses the micro-
processor which monitors your vehicle and controls all of the system's
functions. The GP1000T control unit houses the battery backup siren
and Tilt sensor.
Input
: A physical connection to the system. An input can be provided
by a sensor, switch or through an existing system on the motorcycle.
LED
: Blue light mounted somewhere on the motorcycle. It is used to
indicate the status of your system. It is also used to report triggers and
faults with the system.
the angle of the motorcycle has changed.
Remote
: Hand-held transmitter which operates the various functions of
your system.
Trigger or Triggered Sequence: This is what happens when the alarm
of the siren sounding and indicators flashing for 30-seconds.
Valet Switch
: A small two-button switch mounted somewhere on the
motorcycle. It is used to override the alarm when a remote is lost or
damaged, or to enter or exit Valet mode and for system programming.
Zone
: A zone is a separate input that the alarm can recognise as
unique. Each input to the system is connected to a particular zone.
33
© 2005 directed electronics, inc. all rights reserved
security & convenience expansions
Here we have listed only some of the many expansion options avail-
able. Please contact your dealer for a complete list of all the options
available to you.
Field Disturbance Sensor: An invisible dome of coverage is
established by installing the 508D "radar" sensor. Your security
system can then react to any intrusions on the perimeter of the
field with a warnaway response and if anyone were to intrude
inside the dome the full alarm would sound. Ideal for warning
people away from the motorcycle.
Shock Sensor: The 504C dual-stage shock sensor can be
installed to provide warn-away and alarm protection for your
motorcycle if impacts are detected.
Remote Start
:
The 561T remote start system to provide engine
warm up and battery recharging.
34
health check
Directed Electronics recommends you return to your installing Clifford
®
dealer to have your system checked for correct operation. The first
check is due one year after the installation date and at yearly intervals
thereafter.
nnoottee::
There may be a small charge incurred for this service.
www.directed.com
© 2005 Directed Electronics, Inc. - All rights reserved
G909500 04-05
The company behind this system is Directed Electronics, Inc.
E&OE, specification is subject to change without notice. Some vehicles require optional parts/wiring and a few are incompatible with some features.
Directed®is committed to delivering world-class quality products and services
that excite and delight our customers.
Your factory set 4-digit PIN code is noted below. See this manual for
information on using your PIN code.
Directed Electronics UK office
Unit C Longmead Business Centre
Blenheim Road
Epsom, Surrey KT19 9QQ
place sticker here
Loading...