Clifford AvantGuard 5.1 User Manual

AAvvaannttGGuuaarrdd 55..11

➤

OOwwnneerr’’ss GGuuiiddee

limited lifetime consumer warranty

Directed Electronics ("Directed") promises to the original purchaser to repair or replace with a comparable reconditioned model any Directed unit (hereafter the "unit"), excluding without limitation the siren, the remote transmitters, the associated sensors and accessories, which proves to be defective in workmanship or material under reasonable use during the lifetime of the vehicle provided the following conditions are met: the unit was professionally installed and serviced by an authorized Directed dealer; the unit will be professionally reinstalled in the vehicle in which it was originally installed by an authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer's name, telephone number and address; the authorized dealers name, telephone number and address; complete product description, including accessories; the year, make and model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters and the associated sensors and accessories, carry a one-year warranty from the date of purchase of the same. This warranty is non-transferable and is automatically void if: the original purchaser has not completed the warranty card and mailed it within ten (10) days of the date of purchase to the address listed on the card; the unit's date code or serial number is defaced, missing or altered; the unit has been modified or used in a manner contrary to its intended purpose; the unit has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defects in materials or construction. The warranty does not cover damage to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will determine what constitutes excessive damage and may refuse the return of any unit with excessive damage. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER'S PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC

OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.

This product may be covered by a Guaranteed Protection Plan ("GPP"). See your authorized Directed dealer for details of the plan or call Directed Customer Service at 1-800-876-0800. Directed security systems, including this unit, are deterrents against possible theft. Directed is not offering a guarantee or insurance against vandalism, damage or theft of the automobile, its parts or contents; and hereby expressly disclaims any liability whatsoever, including without limitation, liability for theft, damage and/or vandalism. Directed does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this security system.

Make sure you have all of the following information from your dealer:

A clear copy of the sales receipt, showing the following:

Date of purchase

Your full name and address

Authorized dealer's company name and address

Type of alarm installed

Year, make, model and color of the automobile

Automobile license number

Vehicle identification number

All security options installed on automobile

Installation receipts

trademarks and copyrights

Bitwriter™, Clifford®, Code-Hopping™, Directed®, Doubleguard®, ESP™, FailSafe®, Ghost Switch™, Learn Routine

™

, Nite-Lite®, Nuisance Prevention®Circuitry, NPC®, Revenger®, Silent Mode™, Soft

Chirp

, Stealth Coding™, Stinger®, Valet®, Vehicle Recovery System®, VRS®, and Warn Away®are

all Trademarks or Registered Trademarks of Directed Electronics.

iimmppoorrttaanntt!!

Please note that this manual was intended for US consumers

and therefore includes American phrases or words.

limited lifetime consumer warran-

ty . . . . . . . . . . . . . . . . . . . . . . . . . . .i

trademarks and copyrights . . . . .ii

what is included . . . . . . . . . . . . .3

important information . . . . . . . . .3

system maintenance . . . . . . . .4

your warranty . . . . . . . . . . . . .4

fcc/id notice . . . . . . . . . . . . . . .4

replacement remote controls . . .5

transmitter configurations . . . . . .6

transmitter functions . . . . . . . . . .7

standard configuration . . . . . . .7

arming with transmitter . . . . . .9

arming without transmitter . . .9

disarming . . . . . . . . . . . . . . . .10

disarming without a transmitter .

remote siren silencing . . . . . .11

transmitter chirp muting . . . .12

transmitter sensor disable . . .12

intellistart and smartwindows

sensor bypass . . . . . . . . . . . . .13

auxiliary channel bypass . . . . .13

panic mode with smart door

locking . . . . . . . . . . . . . . . . . .13

disarm/valet mode . . . . . . . . .14

transmitter valet mode . . . . . .15

one-time auto-arming bypass .15

low battery warning . . . . . . .15

multiple event total recall . . . .16

false alarm control technology

(FACT II) . . . . . . . . . . . . . . . . .16

select siren sounds . . . . . . . . . . .17

diagnostics . . . . . . . . . . . . . . . . . .18

arming diagnostics . . . . . . . . .18

disarming diagnostics . . . . . . .19

arm/disarm diagnostic chart . .19

table of zones . . . . . . . . . . . .20

anti-code grabbing (ACG) . . . . .20

high frequency . . . . . . . . . . . . . .21

smart power up II . . . . . . . . . . . .21

power saver mode . . . . . . . . . . .21

programming . . . . . . . . . . . . . . .22

cliffnet wizard installation soft-

ware programming . . . . . . . .22

manual programming instruc-

tions . . . . . . . . . . . . . . . . . . .23

user selectable features . . . . .24

user selectable features descrip-

tions - column one . . . . . . . . .25

user selectable features descrip-

tions - column two . . . . . . . .27

user selectable features descrip-

tions - column three . . . . . . .29

pin programming . . . . . . . . . . . .31

remote start . . . . . . . . . . . . . . . .32

remote start features . . . . . . .32

remote start do's and don'ts .33

contents

remote start/engine shut down .

shortstop mode . . . . . . . . . . .35

low temperature/battery start 36

retained accessory power . . . .36

diesel compatibility . . . . . . . .37

auto-immobilization feature . . .37

auto-immobilization sequence 37

one-time valet feature . . . . . .38

blackjax feature . . . . . . . . . . . . .38

blackjax activation . . . . . . . . .38

blackjax deactivation sequence39

bypass blackjax temporarily . .39

blackjax off warning indicator 40

sensor description section . . . . .41

507M tilt sensor . . . . . . . . . . .41

adjusting the proximity sensor 41

adjusting the omnisensor . . . .43

glossary of terms . . . . . . . . . . . . .46

security & convenience expansions

health check . . . . . . . . . . . . . . . .49

what is included

Control module and harness

IntelliStart module and harness

Two five-button transmitters

Presentation envelope and quick reference card

Two window decal's

External antenna/receiver with harness

Pre-wired blue status LED

PlainView 2 Valet switch

515C Smart Self-Powered siren

Digital dual-zone proximity sensor

Digital dual-zone Omnisensor

507M Digital Tilt sensor

important information

Congratulations on the purchase of your state-of-the-art vehicle

security remote start system. It has been designed to provide years of

trouble-free operation. This system must be installed by an authorized

dealer. Installation of this product by anyone other than an authorized

dealer voids the warranty. As verification of authorization, all autho-

rized dealers are provided with preprinted dealer certificates.

In order to maximize the use of this system, please review this owner's

guide carefully prior to using your system. You can print additional or

replacement copies of this owner’s guide by accessing the Clifford web-

site at www.clifford.com.

system maintenance

The system requires no specific maintenance. Your transmitter is powered by two miniature 3V lithium batteries that will last approximately one year under normal use. When the batteries weaken, operating range will be reduced and the system will provide a low battery warning chirp indication when disarming.

your warranty

Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Make sure you receive the warranty registration from your dealer. It is also necessary to keep your proof of purchase, which reflects that the product was installed by an authorized dealer.

fcc/id notice

This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device.

Directed Electronics, Inc.

Tested to Comply

with FCC Standards

replacement remote controls

You can purchase replacement remote controls from your

Authorized Dealer or on-line at the following web site:

www.directedstore.com

Once you receive your new remote control, please refer to

instructions included on the remote packaging.

transmitter configurations

1. LED Indicator

2. Arm/Disarm Button

3. Trunk Release Button

4. Remote Start Button

5. Silent Arm/Disarm Button

6. Clifford G5 Button

nnoottee::

This manual describes the features and accessories that are included with your system along with information about compatible Clifford accessories that are not included. For a list of included accessories, please refer to the

What Is Included

section of this manual.

transmitter functions

This system uses computer-based code learning to learn the transmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initially comes programmed with standard configuration, but may also be customized using the CliffNet Wizard PC program. The buttons in all of the instructions in this manual correspond to a standard configuration transmitter.

standard configuration

Button

The arming, disarming, and panic function are controlled by this but-

ton.

Button

The trunk release or accessory output A is controlled by this button.

Button

Remote start is controlled by this button.

warning! Operation of the remote start module if the the vehicle starts in gear is contrary to its intended mode of operation. Operating the remote start system under these conditions may result in property damage or personal injury. Immediately cease the use of the unit and repair or disconnect the installed remote start module. Clifford will not be held responsible or pay for installation or reinstallation costs.

Button

Silent arm and disarm is controlled by this button.

Button, then Button

Accessory B output is controlled by these buttons.

Button, then Button

These buttons activate SmartWindows.

Button, then Button

Accessory C output is controlled by these buttons.

Button twice, then Button

These buttons activate remote valet.

Button twice, then Button

These buttons disable the sensors.

Button twice, then Button

These buttons enter safe start mode for manual transmission vehicles

and activate Autostart mode.

Button three times, then Button

These buttons adjust the dual-zone radar sensor.

Button three times, then Button

These buttons adjust the dual-zone omnisensor.

using your system

The buttons used in the instructions in this manual correspond to the

standard transmitter configuration. If your transmitter has been custom

configured, the icons on your transmitter buttons may not correspond

to the indicated functions.

arming with transmitter

You can activate, or arm, the system by pressing on your trans-

mitter for one second. When the system arms, you will hear two short

siren sounds, or chirps, and see the parking lights flash twice. The LED

will begin to flash steadily. If the vehicle’s power door locks have been

connected to the system, the doors will lock.

While the system is armed, the LED status indicator will flash approxi-

mately once per second showing that the system is actively protecting

your vehicle. If you hear more than two chirps when arming, refer to

the Diagnostics section of this guide. These extra chirps confirm a mal-

function autobypass.

arming without transmitter

The security system also can be programmed to arm itself without a

transmitter (called passive arming). If the system is programmed for

passive arming, it will automatically arm 30 seconds after the ignition

is turned off and the system sees you leave the vehicle by opening and

closing a door. The siren will chirp twice and the lights will flash twice

five seconds after the last door has been closed. The system is not actu-

ally armed at that point. The system arms and the doors lock (if con-

nected and programmed for passive locking) at 30 seconds, but the

siren will not chirp. The early chirps provide you with a 25-second

warning prior to arming.

When armed, your vehicle is protected as follows:

The LED will flash as a visible theft deterrent.

Light impacts will trigger the Warning Zone signal. When triggered, the siren will sound for a few seconds.

Heavy impacts will trigger the system. The triggered sequence is 30, 60, or 90 seconds of constant siren sounding and flashing parking lights.

If a protected entry (door, hood, or trunk) is opened, the system will immediately trigger the siren and flash the parking lights.

Digital dual zone radar sensor will protect the interior of the vehicle and it’s contents with an invisible perimeter of protection.

The 507M tilt sensor will trigger the system if an attempt is made to steal the vehicle by towing.

disarming

To disarm the system, press . You will hear a chirp and the parking lights will flash once. If the power locks are connected to the system, the doors will unlock. If the siren chirps three times when disarming, refer to the Diagnostics section of this guide. This is called Tamper Alert. If the siren is active when the system is disarmed you will hear two chirps but the system is not disarmed. (Refer to the Remote Siren

nnoottee::

If any protected entry point (a door or a switch-protected trunk or hood) is open, the system will not passively arm. Additionally, each time a protected entry is triggered during the arming countdown, the 30-second countdown starts over.

Silencing section of this guide.) However, if the alarm completes the full trigger cycle when disarmed you will hear three chirps.

disarming without a transmitter

This feature allows you to disarm the system without the transmitter

should it be lost, damaged, or disabled. In order to disarm without a

transmitter, you must have the vehicle’s ignition key, know where the

PlainView 2 Valet switch is located, and have the PIN code. Be sure to

check with the installer for the location of the PlainView 2 Valet switch.

Please refer to the Disarm/Valet Mode section of this guide for instruc-

tions to enter the pin code.

remote siren silencing

This system offers remote siren silencing. Remote siren silencing is a feature that makes it possible to silence and reset the system when it is triggering without disarming the system. If the system is triggered and the siren has been sounding, press on the transmitter to stop the trigger and return the unit to the armed state. This prevents you from disabling the system should you wish to silence it without visually checking the vehicle. After resetting the system, press again to disarm the system.

transmitter chirp muting

To temporarily turn off the arm or disarm chirps, use transmitter chirp

muting. Simply press on the transmitter, and the confirmation

chirp(s) will be eliminated for that one operation only. The parking

lights will flash to confirm the arm/disarm command. If you want the

arm/disarm chirps turned off permanently, please refer to the User-

Selectable Features section of this guide.

transmitter sensor disable

To temporarily disable a sensor input, arm the system, press twice

and then . The lights will flash four times and all sensor warn

away zones are bypassed. Press the buttons again; the lights flash four

times and both warn away and full trigger sensor zones are bypassed

until the system is disarmed. This can be performed anytime the system

is armed.

1. Arm the system.

2. Press twice and then .

3. The lights will flash four times; all warn away zones are now bypassed.

4. Transmit the sensor bypass channel again.

5. The lights will flash four more times; the sensor warn away and full trigger zones are now bypassed.

6. The sensor zones will reset when disarmed.

intellistart and smartwindows sensor bypass

When the system sees a command to start the vehicle via the Intellistart, it bypasses all sensors and will continue to bypass these sensors until the remote start shuts down.

When the system sees a SmartWindows command for up or down operation, the unit will automatically bypass all sensors until the windows complete their operation.

auxiliary channel bypass

All sensor will be bypassed while a pulsed or timed auxiliary output channel is active.

panic mode with smart door locking

If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter! Just press for two seconds to enter Panic Mode. The siren will sound and the parking lights will flash for the programmed duration. If the ignition is on, the doors will lock; if the ignition is off, the doors will unlock. To stop Panic Mode at any time press on the transmitter again.

+ 37 hidden pages