Clevo W760K User Manual
V09.1.00
I
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©June 2009
Trademarks
AMD® Athlon™ is a trademark of Advanced Micro Devices, Inc.
II
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experie nc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference.
And
2. This device must accept any interference, including interference that may cause undesired operation of the
device.
III
Preface
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
If your purchase option includes both Wireless LAN and 3.5G modules, then the appropriate antennas will be installed. Note
that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or o perate in
conjunction with any other antenna or transmitter.
IV
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitche n sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using this eq uipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC
Output of 19V, 3.42A OR 18.5V, 3.5A (65 Watts) minimum AC/DC Adapter.
This Computer’s Optical Device is a Laser Class 1 Product
V
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
2. Keep it dry, and don’t overheat it. Keep the computer and powe r supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
VI
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g proc edu res for the comput er. Shut the computer down properly and don ’t forge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
5. Take care when using peripheral devices.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
Do not disassemble the computer by yourself.
Perform routine maintenance
on your computer.
Use only approved brands of
peripherals.
Unplug the power cord befor e
attaching peripheral devices.
VII
Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady , uninte rrupted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VIII
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way . Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to your servi ce represent ative or qual-
ified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
IX
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and
screw(s) before turning the computer on.
X
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its ca rrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your documents are prepared.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocke d. To prevent your
computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
XI
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XII
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher th an your hips. Place yo ur feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XIII
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light .
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front o f you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idl e time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too lo ng).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
XIV
Preface
XV
Preface
Contents
Notice ................................................................................. I
FCC Statement .............................................................II
FCC RF Radiation Exposure Statement: ................... III
Instructions for Care and Operation ........................... V
Power Safety .............................................................VII
Battery Precautions ................................................. VIII
Cleaning ..................................................................... IX
Servicing .................................................................... IX
Travel Considerations .................................................X
Quick Start Guide
Overview ........................................................................1-1
Advanced Users ...........................................................1-2
Beginners and Not-So-Advanced Users ......................1-2
Warning Boxes ............................................................1-2
Not Included ................................................................1-3
System Startup .............................................................1-4
Operating System Setup ................................................1-5
System Software ..........................................................1-6
Model Differences .......................................................1-7
System Map: LCD Panel Open - Model A ....................1-8
System Map: LCD Panel Open - Model B ....................1-9
LED Indicators ................................................. ............1-10
Hot Key Buttons ..........................................................1-11
Keyboard - Model A ....................................................1-12
Keyboard - Model B .......................................... .... ......1-13
Function/Hot Key Indicators .......................................1-14
System Map: Front & Left Views ................................1-15
System Map: Right & Rear Views .............................. 1-16
System Map: Bottom View - Model A ........................1-17
System Map: Bottom View - Model B ........................1-18
Windows Vista Start Menu & Control Panel ...............1-19
Video Features .............................................................1-20
Display Devices & Options ......................... .... ..........1-21
Power Options ............................................ ..................1-22
Features & Components
Overview ........................................................................2-1
Hard Disk Drive .............................................................2-2
Optical (CD/DVD) Device ............................................2-3
Loading Discs ..............................................................2-3
Handling CDs or DVDs ...............................................2-4
DVD Regional Codes ..................................................2-5
7-in-1 Card Reader .........................................................2-6
ExpressCard Slot ............................................................2-7
Inserting and Removing ExpressCards ........................2-7
XVI
Preface
TouchPad and Buttons/Mouse .......................................2-8
Audio Features .............................................................2-10
Adding a Printer ...........................................................2-11
USB Printer ..............................................................2-11
Parallel Printer ..........................................................2-11
Power Management
Overview ........................................................................3-1
The Power Sources .......................................... .... ..........3-2
AC/DC Adapter .......... .... .... .... .....................................3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Plans ...................................................................3-4
Power-Saving States ......................................................3-6
Sleep ...........................................................................3-6
Hibernate ....................................................................3-7
Shut Down ..................................................................3-7
Configuring the Power Buttons .....................................3-8
Resuming Operation ...................................................3-9
Battery Information .....................................................3-10
Battery Power ...........................................................3-10
Conserving Battery Power .........................................3-11
Battery Life ................................................................3-12
New Battery ..............................................................3-12
Recharging the Battery with the AC/DC Adapter .....3-12
Proper handling of the Battery Pack .........................3-13
Battery FAQ ..............................................................3-14
Drivers & Utilities
What to Install ................................................................4-1
Module Driver Installation ..........................................4-1
Driver Installation ..........................................................4-2
Updating/Reinstalling Individual Drivers ...................4-4
User Account Control (Win Vista) ..............................4-4
Windows Security Message .........................................4-4
New Hardware Found ..................................................4-5
Driver Installation Procedure .......................................4-5
Video ..........................................................................4-5
Audio ..........................................................................4-5
LAN ............................................................................4 -6
TouchPad .................................................................... 4-6
CardReader ................................................................. 4-6
Hot Key ......................................................................4-6
Optional Drivers ..........................................................4-7
Wireless LAN Module ...............................................4-7
PC Camera Module ....................................................4-7
3.75G/HSPA Module .................................................4-7
XVII
Preface
BIOS Utilities
Overview ........................................................................5-1
The Power-On Self Test (POST) ................................... 5-2
Failing the POST .........................................................5-3
Fatal Errors .................................................................5-3
Non-Fatal Errors .........................................................5-3
The Setup Program ........................................................5-4
Entering Setup .............................................................5-4
Setup Screens ...............................................................5-5
Main Menu .....................................................................5-6
System Time & Date (Main Menu) ...............................5-6
SATA Port 1/2 (Main Menu) .........................................5-7
System/Extended Memory (Main Menu) ......................5-7
BIOS Revision/KBC/
EC Firmware Revision (Main Menu) ............................5-7
Advanced Menu .............................................................5-8
Advanced Chipset Control (Advanced Menu) ..............5-8
Installed O/S (Advanced Menu) ....................................5-9
SATA Class ID (Advanced Menu) ................................5-9
Legacy USB Support (Advanced Menu) .......................5-9
Boot-time Diagnostic Screen (Advanced Menu) ...........5-9
Reset Configuration Data (Advanced Menu) ..............5-10
Power On Boot Beep (Advanced Menu) .....................5-10
Battery Low Alarm Beep (Advanced Menu) ...............5-10
Security Menu ..............................................................5-11
Set Supervisor Password (Security Menu) ..................5-11
Set User Password (Security Menu) ............................5-12
Password on boot: (Security Menu) .............................5-12
Boot Menu ...................................................................5-13
Exit Menu ....................................................................5-14
Upgrading The Computer
Overview ........................................................................6-1
When Not to Upgrade ..................................................6-2
Removing the Battery ....................................................6-3
Upgrading the Hard Disk Drive .....................................6-4
Upgrading the Optical (CD/DVD) Device ....................6-7
Upgrading the System Memory (RAM) ........................6-9
Modules & Options
Overview ........................................................................7-1
Bluetooth Module ..........................................................7-2
Bluetooth Configuration in Windows Vista ...............7-3
Wireless LAN Module ...................................................7-6
802.11b/g/n Driver Installation ..................................7-6
Connecting to a Wireless Network ..............................7-7
Windows Mobility Center .........................................7-10
PC Camera Module ......................................................7-11
PC Camera Driver Installation .................................7-12
3.75G/HSPA Module ...................................................7-19
XVIII
Preface
HSPA Modem Interface ............................................7-24
HSPA Modem Interface Installation ........................7-24
HSPA Modem Interface ...........................................7-25
Adding a Profile .......................................................7-27
Contacts .................................................................... 7-29
Messages ...................................................................7-30
Settings .....................................................................7-31
Mobile Partner ...........................................................7-33
Mobile Partner Application Installation ...................7-33
Mobile Partner Application ...................................... 7-34
Profile Management .................................................7-34
Troubleshooting
Overview ........................................................................8-1
Basic Hints and Tips ......................................................8-2
Backup and General Maintenance .................................8-3
Viruses ........................................................................... 8-4
Upgrading and Adding New Hardware/Software ..........8-5
Problems and Possible Solutions ...................................8-7
Screen Resolution Error ...............................................8-13
Interface (Ports & Jacks)
Overview .......................................................................A-1
Ports and Jacks ..............................................................A-2
ATI Video Driver Controls
ATI Video Driver Installation .......................................B-1
ATI Catalyst® Control Center ......................................B-2
Attaching Other Displays ..............................................B-4
Display Modes ..............................................................B-6
Clone Mode ...............................................................B-7
Extended Mode .........................................................B-8
Theater Mode ..............................................................B-11
PowerPlay™ ............................................................... B-12
Specifications
Processor ....................................................................... C-2
Core Logic ....................................................................C-2
Display .......................................................................... C-2
Memory .........................................................................C-2
Video Adapter ...............................................................C-2
BIOS .............................................................................C-2
Storage .......................................................................... C-2
Audio ............................................................................C-2
Keyboard & Pointing Device ........................................C-2
Interface ........................................................................ C-2
Card Reader ..................................................................C-2
Slots ..............................................................................C-2
Communication .............................................................C-3
XIX
Preface
Power Management ......................................................C-3
Power ............................................................................ C-3
Security ......................................................................... C-3
Operating System .......................................................... C-3
Environmental Spec ......................................................C-3
Dimensions & Weight .................................................. C-3
Optional ........................................................................ C-3
Windows XP Information
Operating System Setup ...............................................D-2
DVD Regional Codes ...................................................D-3
Windows XP Start Menu & Control Panel ...................D-4
TouchPad and Buttons/Mouse ......................................D-5
Function/Hot Key Indicators ........................................D-6
Audio Features ..............................................................D-7
Video Features ..............................................................D-8
Display Devices & Options...........................................D-9
ATI Catalyst® Control Center ....................................D-10
Attaching Other Displays ...........................................D-12
Clone Mode .................................................................D-14
Extended Mode............................................................D-15
Stretched Mode............................................................D-16
Theater Mode ..............................................................D-18
PowerPlay™ ............................................................... D-19
Power Management Features ......................................D-20
Advanced Configuration and Power Interface ............D-20
The Power Sources .....................................................D-21
AC/DC Adapter ...........................................................D-21
Battery..........................................................................D-21
Turning On the Computer ...........................................D-22
Power Schemes ...........................................................D-23
System Power Options ................................................D-25
Hibernate Mode vs. Shutdown.....................................D-25
Stand by Mode vs. Hibernate Mode ............................D-25
Configuring the Power Button ....................................D-27
Battery Information .....................................................D-28
Recharging the Battery with the AC/DC Adapter .......D-29
Battery Guidelines ....... ... .... .....................................D-30
Battery FAQ.................................................................D-31
Driver Installation .......................................................D-32
Updating/Reinstalling Individual Drivers....................D-33
Driver Installation Procedure.......................................D-34
Module Drivers............................................................D-36
Bluetooth Module .......................................................D-37
WLAN Module ...........................................................D-42
PC Camera Module .....................................................D-44
3.75G/HSPA Module ..................................................D-50
XX
Preface
Overview 1 - 1
Quick Start Guide
1
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard/34/54), TouchPad & Mouse, Audio & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Bluetooth, PC Camera, Wireless LAN, 3.75G/HSPA and Fin-
gerprint modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the ATI Video driver controls.
• Appendix C The computer’s specification.
• Appendix D Information on the Windows XP OS.
1 - 2 Overview
Quick Start Guide
1
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Notes
Check the light colored
boxes with the mark
above to find detailed information about the computer’s features.
Overview 1 - 3
Quick Start Guide
1
Not Included
Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and
database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If
your system hasn’t been properly configured (your service representative may have already done that for you); refer to
Chapter 4 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1 - 4 Overview
Quick Start Guide
1
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Use one hand to raise the
lid/LCD to a comfortable viewing angle (do not exceed 120 degrees);
use the other
hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by
the lid/LCD).
Figure 1 - 1 - Opening the Lid/LCD/Computer with AC/DC Adapter Plugged-In
Shutdown
Note that you should always shut your computer down by choosing the Shut Down command from the Lock Button Menu
in Windows Vista. This will help prevent hard disk or system problems.
Operating System Setup 1 - 5
Quick Start Guide
1
Operating System Setup
If you are installing new system software, or are re-configuring your computer for a different system, make sure you
configure the appropriate OS setting in the BIOS before installing a new operating system (Note: If you have installed
the Windows Vista operating system with AHCI mode enabled, DO NOT disable AHCI mode or you will need to
reinstall the Windows Vista OS).
1. Start-up the computer and press <F2> to enter the BIOS.
2. Go to the Advanced menu, select “Installed O/S” and make sure the appropriate operating system is selected.
3. Go to the Exit menu and select “Exit Saving Changes” (or press F10 and select “Yes” then press Enter) and
press Enter to exit the BIOS and reboot the computer.
Figure 1 - 2 - Advanced BIOS Menu
Main AAdvanced Security Boot Exit
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Advanced
Select the operating
system installed
on your system which
you will use most
commonly.
Note: An incorrect
setting can cause
some operating
systems to display
unexpected behavior.
PhoenixBIOS Setup Utility
Advanced Chipset Control
Installed O/S: [VISTA]
SATA Class ID: [AHCI]
Legacy USB Support: [Enabled]
Boot-time Diagnostic Screen: [Disabled]
Reset Configuration Data: [No]
Power on Boot Beep: [Disabled]
Battery Low Alarm Beep: [Disabled]
Only available if Windows Vista
is selected as the O/S.
SATA Mode Selection
Make sure that you have selected the appropriate SATA Class ID for your hard disk. If
you have installed the Vista O/S with AHCI
or IDE mode selected, do not chan ge the setting (otherwise you will need to reinstall your
O/S).
1 - 6 Operating System Setup
Quick Start Guide
1
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the following operating systems are supported.
Table 1 - 1 - Operating Systems Supported
*Note: For information on the Windows XP OS (specifically power, video and driver information) see “Win-
dows XP Information” on page D - 1.
Operating System & Version Note
*Windows XP - SP3 (Home or Professional)
In order to run Windows XP without limitations
or decreased performance, your computer
requires a minimum 512MB of system memory
(RAM)
Windows Vista - SP1 (Home Basic, Home Premium, Business, Enterprise
and Ultimate Editions)
In order to run Windows Vista without
limitations or decreased performance, your
computer requires a minimum 1GB of system
memory (RAM).
Windows Vista Service Pack 1
Make sure you install Windows Vista Service Pack 1 (or a Windows Vista version which includes Service Pack 1) before installing
any drivers. Go to the Microsoft website for download details, or contact your service center.
Operating System Setup 1 - 7
Quick Start Guide
1
Model Differences
This notebook series includes two different model types. The models differ as indicated in the table below however
all other features, modules and specifications are identical (see Appendix D).
Table 1 - 2 - Model Differences
Feature Model A Model B
Display Type
Supported
14.1" WXGA (1280 * 800) TFT LCD 15.6" HD 16:9 Wide Screen (1366 * 768)TFT LCD
Design
1 - 8 System Map: LCD Panel Open - Model A
Quick Start Guide
1
System Map: LCD Panel Open - Model A
Figure 1 - 3
LCD Panel Open
(Model A)
1. Built-In PC Camera
(
Optional
)
2. LCD
3. Speakers
4. Power Button
5. Hot Key Buttons
6. Keyboard
7. Built-In Microphone
8. Touchpad &
Buttons
9. LED Indicators
9
2
5
1
7
8
4
6
33
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic
transmission devices aboard aircraft is
usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.
Use the key combinations to toggle
power to the 3.75G/HSPA/WLAN/
Bluetooth modules, and check the LED
indicator icon to see if the modules are
powered on or not (see Table 1 - 6, on
page 1 - 14/ Table 1 - 4, on page 1 -
10).
9
Touchpad Buttons
(valid operation area)
8
Loading...