Clevo W650SF, W650SJ, W670SFQ User guide

V14.1.00

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©February 2014

Trademarks

Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

ErP Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:

• Off Mode < 0.5W

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc ed radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interfer ence that may cause undesired operation of the

device.

FCC RF Radiation Exposure Statement:



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

If your purchase option includes both Wireless LAN and 3G modules, then the appropriate antenna s will be installed. Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co -located or o perate in conjunction with any other antenna or transmitter.

Important Notice - 3G & Bluetooth/Wireless LAN Modules

In order to comply with FCC regulations you should NOT operate the 3G module and the Bl uetoo th/Wirele ss LAN modules at the same time as this may disrupt radio frequency, and cause interference. When the 3G module is p owered on, make sure that the Bluetooth/Wireless LAN modules are powered off.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit:

• Models A & C: Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz,

DC Output of 19V, 4.74A (90 Watts) minimum.

• Models B & D: Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz,

DC Output of 19.5V, 6.15A (120Watts) minimum.

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive heat or direct sunlight.

Do not leave it in a place where foreign matter or moisture may affect the system.

Don’t use or store the computer in a humid environment.

Do not place the computer on any surface that will block the Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

5. Take care when using peripheral devices.

Use only approved brands of peripherals.

VIII

Do not disassemble the computer by yourself.

Unplug the power cord befor e attaching peripheral devices.

Perform routine maintenance on your computer.

Power Safety



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).

You must also remove your battery in order to prevent accidentally turning the machine on. Before removing

the battery disconnect the AC/DC adapter from the computer.

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a

steady , uninterru pted power suppl y. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third

prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not

by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current

load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power

supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha-

nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-

ture environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

Battery Precautions



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu al-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

Preface



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

XII

Preface



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prev ent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both

hardware and software. Make sure your documents are prepared.

XIII

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.

XIV

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and /or desk so that the ke yboard is a t or slightly below the level

of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a

footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when

you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent and

short breaks are better than fewer and longer breaks.

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier.

XVI

Preface

Contents

Notice .............................................................................................................................................................I

ErP Off Mode Power Consumption Statement: ...........................................................................................II

FCC Statement ............................................................................................................................................IV

FCC RF Radiation Exposure Statement: .....................................................................................................V

Instructions for Care and Operation ......................................................................................................... VII

Power Safety ...............................................................................................................................................IX

Polymer Battery Precautions .......................................................................................................................X

Battery Precautions .....................................................................................................................................XI

Cleaning .................................................................................................................................................... XII

Servicing ................................................................................................................................................... XII

Travel Considerations ..............................................................................................................................XIII

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Startup ...........................................................................................................................................1-4

System Software ........................................................................................................................................1-5

Model Differences .....................................................................................................................................1-6

XVII

Preface

Models A & B: LCD Panel Open ..............................................................................................................1-7

Models C & D: LCD Panel Open ..............................................................................................................1-8

LED Indicators ...........................................................................................................................................1-9

Keyboard - Models A & B .......................................................................................................................1-10

Keyboard - Models C & D .......................................................................................................................1-11

Keyboard Shortcuts .................................................................................................................................1-12

Function/Hot Key Indicators ...................................................................................................................1-13

Control Center .........................................................................................................................................1-14

Models A & B: Front & Left Views ........................................................................................................1-15

Models C & D: Front & Left Views ........................................................................................................1-16

Models A & B: Right & Rear Views .......................................................................................................1-17

Models C & D: Right & Rear Views .......................................................................................................1-18

Models A & B: Bottom View ..................................................................................................................1-20

Models C & D: Bottom View ..................................................................................................................1-21

Windows 8.1 Control Panel .....................................................................................................................1-22

Windows 8.1 Start Screen & Desktop .....................................................................................................1-27

Apps & Tiles ............................................................................................................................................1-28

Desktop Application ................................................................................................................................1-29

The Charms Bar .......................................................................................................................................1-30

Windows 8.1 Taskbar ..............................................................................................................................1-32

Video Features .........................................................................................................................................1-33

To Configure Displays from Devices (Charms Bar): .............................................................................E-33

XVIII

Preface

Power Options .........................................................................................................................................1-37

Shut Down, Restart or Sleep (Charms Bar) ............................................................................................E-37

Running Apps ..........................................................................................................................................1-38

Features & Components

Overview ....................................................................................................................................................2-1

Hard Disk Drive .........................................................................................................................................2-2

Optical (CD/DVD) Device ........................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-In-1 Card Reader .............................................................................................................................2-6

Touchpad/Clickpad and Buttons/Mouse ....................................................................................................2-7

One-Finger ...............................................................................................................................................2-11

Multi-Finger .............................................................................................................................................2-14

Additional ................................................................................................................................................2-16

Audio Features .........................................................................................................................................2-17

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

Battery ........................................................................................................................................................3-2

XIX

Preface

Turning On the Computer ..........................................................................................................................3-3

Shutting the Computer Down ....................................................................................................................3-4

Power Plans ...............................................................................................................................................3-5

Power-Saving States ..................................................................................................................................3-7

Sleep ..........................................................................................................................................................3-7

Hibernate ....................................................................................................................................................3-8

Shut down ..................................................................................................................................................3-8

Configuring the Power Buttons .................................................................................................................3-9

Resuming Operation ................................................................................................................................3-11

Power Conservation Modes .....................................................................................................................3-12

Battery Information .................................................................................................................................3-14

Battery Power ..........................................................................................................................................3-14

Conserving Battery Power .......................................................................................................................3-15

Battery Life ..............................................................................................................................................3-16

New Battery .............................................................................................................................................3-16

Recharging the Battery with the AC/DC Adapter ...................................................................................3-16

Proper handling of the Battery Pack ........................................................................................................3-17

Battery FAQ .............................................................................................................................................3-18

Drivers & Utilities

What to Install ............................................................................................................................................4-1

Module Driver Installation ........................................................................................................................4-1

Preface

Driver Installation ......................................................................................................................................4-2

Updating/Reinstalling Individual Drivers ..................................................................................................4-5

User Account Control ................................................................................................................................4-6

Windows Security Message .......................................................................................................................4-6

New Hardware Found ................................................................................................................................4-6

Driver Installation Procedure .....................................................................................................................4-7

Chipset .......................................................................................................................................................4-7

Video (VGA) .............................................................................................................................................4-7

NVIDIA Video (VGA) ..............................................................................................................................4-7

LAN ...........................................................................................................................................................4-7

CardReader Patch ......................................................................................................................................4-7

CardReader ................................................................................................................................................4-7

Touchpad ...................................................................................................................................................4-8

Hot Key ......................................................................................................................................................4-8

Airplane .....................................................................................................................................................4-8

MEI Driver .................................................................................................................................................4-8

Audio .........................................................................................................................................................4-8

Optional Drivers ......................................................................................................................................4-10

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Setup Utility ........................................................................................................................................5-2

XXI

Preface

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

Setup Screens .............................................................................................................................................5-4

Main Menu .................................................................................................................................................5-5

System Time & Date (Main Menu) ...........................................................................................................5-5

SATA Port # (Main Menu) ........................................................................................................................5-6

CPU/System/Extended Memory: (Main Menu) ........................................................................................5-6

MB Series / BIOS Revision / KBC/EC firmware Revision ......................................................................5-6

Advanced Menu .........................................................................................................................................5-7

Intel(R) Rapid Start Technology (Advanced Menu) .................................................................................5-7

Intel Anti-Theft Technology (Advanced Menu) ........................................................................................5-8

SATA Mode (Advanced Menu) ................................................................................................................5-8

Boot Logo (Advanced Menu) ....................................................................................................................5-8

Power On Boot Beep (Advanced Menu) ...................................................................................................5-9

Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9

Security Menu ..........................................................................................................................................5-10

Set Supervisor Password (Security Menu) ..............................................................................................5-10

Set User Password (Security Menu) ........................................................................................................5-11

Password on boot: (Security Menu) ........................................................................................................5-11

Secure Boot Control (Security Menu) .....................................................................................................5-12

Boot Menu ...............................................................................................................................................5-13

XXII

Preface

Boot Option Priorities (Boot Menu) ........................................................................................................5-14

UEFI Boot (Boot Menu) ..........................................................................................................................5-14

Exit Menu ................................................................................................................................................5-15

Upgrading The Computer

Overview ....................................................................................................................................................6-1

When Not to Upgrade ................................................................................................................................6-2

Removing the Battery ................................................................................................................................6-3

Removing the Component Bay Cover - Model A .....................................................................................6-4

Removing the Component Bay Cover - Model B .....................................................................................6-5

Replacing the Component Bay Cover - Model A ......................................................................................6-6

Replacing the Component Bay Cover - Model B ......................................................................................6-7

Upgrading the Hard Disk Drive .................................................................................................................6-8

Removing the Hard Disk Drive .................................................................................................................6-9

Upgrading the Optical (CD/DVD) Device ..............................................................................................6-12

Upgrading the System Memory (RAM) ..................................................................................................6-13

Modules & Options

Overview ....................................................................................................................................................7-1

PC Camera Module ....................................................................................................................................7-3

PC Camera Audio Setup ............................................................................................................................7-4

Camera App ...............................................................................................................................................7-5

Camera Options .........................................................................................................................................7-6

XXIII

Preface

Taking Pictures/Capturing Video ..............................................................................................................7-7

Camera Roll ...............................................................................................................................................7-8

Wireless LAN Module .............................................................................................................................7-12

3rd Party 802.11b/g/n Driver Installation ................................................................................................7-13

Intel® WLAN Driver Installation ............................................................................................................7-13

WLAN Configuration in Windows .........................................................................................................7-14

Bluetooth & WLAN Combo Module ......................................................................................................7-17

3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-18

Intel Bluetooth Combo Driver Installation ..............................................................................................7-18

Bluetooth Configuration in Windows ......................................................................................................7-19

Intel® Rapid Storage Technology ...........................................................................................................7-22

IRST Driver Installation ..........................................................................................................................7-22

Intel® Rapid Start Technology Driver ....................................................................................................7-23

Intel® Rapid Start Technology Configuration ........................................................................................7-24

Intel® Rapid Start Technology Driver Installation .................................................................................7-30

Sound Blaster Cinema EQ .......................................................................................................................7-31

Sound Blaster Cinema EQ Installation ....................................................................................................7-31

Sound Blaster Cinema Application .........................................................................................................7-32

Sound Blaster Cinema Controls ...............................................................................................................7-34

Wireless Display ......................................................................................................................................7-36

Wireless Display Configuration ..............................................................................................................7-37

3G Module ...............................................................................................................................................7-40

XXIV

Preface

3G Configuration in Windows .................................................................................................................7-42

EM820W 3G Module PIN Code & Power-Saving ..................................................................................7-45

Troubleshooting

Overview ....................................................................................................................................................8-1

Basic Hints and Tips ..................................................................................................................................8-2

Backup and General Maintenance .............................................................................................................8-3

Viruses .......................................................................................................................................................8-4

Upgrading and Adding New Hardware/Software ......................................................................................8-5

Problems and Possible Solutions ...............................................................................................................8-7

EM820W 3G Module PIN Code & Power-Saving ..................................................................................8-15

Resolving the “Insert a SIM” issue with the 3G Module (Windows 8.1) ...............................................8-17

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Notebook Ports and Jacks .........................................................................................................................A-2

Control Center

Overview ...................................................................................................................................................B-1

Video Driver Controls

Video (VGA) ............................................................................................................................................C-1

NVIDIA Video (VGA) .............................................................................................................................C-1

XXV

Preface

Dynamic Video Memory Technology ......................................................................................................C-1

Microsoft Hybrid Graphics .......................................................................................................................C-2

Intel® HD Graphics Control Panel ...........................................................................................................C-4

Display Devices & Options ....................................................................................................................C-14

Attaching Other Displays .......................................................................................................................C-15

Attaching Other Displays - Devices (Charms Bar) ................................................................................C-18

Configuring an External Display In Windows .......................................................................................C-19

NVIDIA Control Panel ...........................................................................................................................C-21

Customization Options ...........................................................................................................................C-23

Set PhysX® Configuration .....................................................................................................................C-27

HDMI Audio Configuration ...................................................................................................................C-28

Specifications

Processors .................................................................................................................................................D-2

Core Logic ................................................................................................................................................D-2

Display ......................................................................................................................................................D-2

Memory .....................................................................................................................................................D-2

Video Controller .......................................................................................................................................D-2

Storage ......................................................................................................................................................D-3

Audio ........................................................................................................................................................D-3

Keyboard & Pointing Device ....................................................................................................................D-3

Interface ....................................................................................................................................................D-3

XXVI

Preface

Card Reader ..............................................................................................................................................D-4

Slot ............................................................................................................................................................D-4

Communication .........................................................................................................................................D-4

Power Management ..................................................................................................................................D-4

Power ........................................................................................................................................................D-4

Battery .......................................................................................................................................................D-5

Power Management ..................................................................................................................................D-5

Indicators ..................................................................................................................................................D-5

BIOS .........................................................................................................................................................D-5

Security .....................................................................................................................................................D-5

Features .....................................................................................................................................................D-5

Operating System ......................................................................................................................................D-5

Environmental Spec ..................................................................................................................................D-5

Dimensions & Weight ..............................................................................................................................D-5

XXVII

Preface

XXVIII

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, card reader), Touchpad/Mouse and Audio.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth & WLAN Combo,

Sound Blaster Cinema, Intel Technology and 3G modules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on Control Center.

• Appendix C Information on the video driver controls.

• Appendix D The computer’s specification.

Overview 1 - 1



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on

page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in the Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you); refer to

Chapter 4 for installation instructions.

Ports and Jacks

See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Not Included

Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.

Overview 1 - 3



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command from the Power item in Settings in the Charms Bar (use the Windows Logo Key +

C key combination to access the Charms Bar) in Windows 8.

This will help prevent hard disk or system problems.

130°

Quick Start Guide

System Startup

1. Remove all packing materials, and place the computer on a stable surface.

2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter (make sure you use the adapter when first setting up the computer, as to safeguard the computer during shipping the battery will be locked to not power the system until first connected to the AC/DC adapter).

4. Use one hand to raise the

hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).

lid/LCD to a comfortable viewing angle (

do not exceed 130 degrees

);

use the other

Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In

1 - 4 System Startup

Quick Start Guide



Windows OS

In order to run Windows 8.1 (64-bit) without limitations or decreased performance, your computer requires a minimum 2GB of system memory (RAM).

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 (64-bit) operating system is supported.

Note: In order to run Windows without limitations or decreased performance, your computer requires a mini- mum 1GB of system memory (RAM).

System Startup 1 - 5

Quick Start Guide

Model Differences

This notebook series includes four different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual (see Appendix D for details).

Feature Model A Model B Model C Model D

Intel® HD Graphics 4600 /

Video

Controller

Display

3G Module

Power Supply

Dimensions

& Weight

Intel® HD Graphics

NVIDIA® GeForce

Video

15.6” / 39.62cm HD (1366 * 768) / FHD (1920 * 1080), 16:9 (3.8mm thick) Backlit Panel

Full Size Mini-Card 3G Module with USB Interface

Full Range AC/DC

Adapter

DC Output 19V, 4.74A

(90 Watts)

374mm(w) * 252mm(d) * 14 - 31.4mm(h)

2.5kg with 48.84WH Battery & ODD

374mm(w) * 249mm(d) * 14.8 - 32.8mm(h)

2.5kg with 48.84WH Battery & ODD

1 - 6 System Startup

Intel® HD Graphics 4600 /

Intel® HD Graphics

840M

NVIDIA® GeForce GTX

850M Video

(Factory Option)

Full Range AC/DC

Adapter

DC Output 19.5V, 6.15A

(120 Watts)

OR (Design Style Dependent)

Table 1 - 1 - Model Differences

Intel® HD Graphics 4600 /

Intel® HD Graphics

NVIDIA® GeForce

Video

17.3" (43.94cm) HD+ (1600 * 900) / FHD (1920 *

Full Range AC/DC

Adapter

DC Output 19V, 4.74A

(90 Watts)

413mm(w) * 272mm(d) * 36.4mm(h)

3.1kg with 62.16WH Battery & ODD

840M

1080), 16:9 Backlit Panel

Not Supported

Intel® HD Graphics 4600 /

Intel® HD Graphics

NVIDIA® GeForce GTX

850M Video

Full Range AC/DC

Adapter

DC Output 19.5V, 6.15A

(120 Watts)

Models A & B: LCD Panel Open

Figure 1 - 2

LCD Panel Open

1. Built-in PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Power Button

6. LED Indicators (Caps, Num & Scroll Lock)

7. Keyboard

8. Touchpad & Buttons

Touchpad Buttons (valid operation area)

Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines indicated on the right.



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the 3G/WLAN/Blue- tooth module(s) are OFF if you are using the computer aboard aircraft.

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/ Off, and check the LED indicator for the power status (see Table 1 - 4, on

page 1 - 12/ Table 1 - 2, on page 1 - 9).

Quick Start Guide

Models A & B: LCD Panel Open 1 - 7

Figure 1 - 3

LCD Panel Open

1. Built-in PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Power Button

6. LED Status Indicators (Caps, Num & Scroll Lock)

7. Keyboard

8. Clickpad & Buttons

Note that the clickpad has a defined valid operational area of sensitivity indicated within the sensor area of the illustration below. See “Touchpad

Sensitivity” on page 2 - 7.



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN & Bluetooth module(s) are OFF if you are using the computer aboard aircraft.

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/ Off, and check the LED indicator for the power status (see Table 1 - 4, on page 1

- 12/ Table 1 - 2, on page 1

- 9).

Quick Start Guide

Models C & D: LCD Panel Open

1 - 8 Models C & D: LCD Panel Open

Quick Start Guide

LED Indicators

The LED indicators on the computer display helpful information about the current status of the computer.

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking Green

Orange The Battery is Charging

Green The Battery is Fully Charged

Blinking Orange

Green Hard Disk Activity

Green

Table 1 - 2 - LED Power Indicators

The Computer is in Sleep

Mode

The Battery Has Reached

Critically Low Power Status

Airplane Mode is ON (the

WLAN, Bluetooth & 3G

Modules are OFF)

Icon Color Description

Blue Number Lock Activated

Blue

Blue Caps Lock Activated

Scroll Lock Activated (to activate

press Fn & Scr Lk)

Table 1 - 3 - LED Status Indicators

LED Indicators 1 - 9



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.

NumLk & ScrLk

Hold down the Fn Key and either NumLk or ScrLk to enable number or scroll lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk & ScrLk Keys

Fn Key

Keypad

Windows Logo Key

Menu/Application Key



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Quick Start Guide

Keyboard - Models A & B

The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.

Figure 1 - 4 - Keyboard - Models A & B

1 - 10 Keyboard - Models A & B

Keyboard - Models C & D



Other Keyboards

NumLk & ScrLk

Hold down the Fn Key and either NumLk or ScrLk to enable number or scroll lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk & ScrLk Keys

Fn Key

Keypad

Windows Logo Key

Menu/Application Key

Note that the F12 key (to toggle illuminated keyboard brightness in combination with the Fn key) is applicable to illuminated keyboards only, and will not appear on non-illuminated keyboards.



Special Characters

The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.

Quick Start Guide

Figure 1 - 5 - Keyboard - Models C & D

Keyboard - Models C & D 1 - 11



Windows Logo

Keyboard Shortcut

Use the Windows logo key + D key com- bination to switch from the Start screen to the Windows Desktop.

Menu/Application

Keyboard Shortcut

When the Desktop app is running you can use the Menu/Application key on the keyboard to act as a mouse right-click. In the Start screen this function is useful to quickly display Cus-

tomize Apps.

Quick Start Guide

Keyboard Shortcuts

The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in

Windows

1 - 12 Keyboard Shortcuts

Windows Logo

Key +

Tap Winkey

CDisplay Charms menu D Switch to the Windows Desktop and toggle show Desktop

F Display file Search

I Open the Settings charm

K Open the Connect charm

L Lock the computer and display the Lock screen P Display the Second Screen menu (see Figure 1 - 25 on page 1 - 33) R Switch to the Windows Desktop and display the Run dialog box Z Access the Customize Bar (see Figure 1 - 20 on page 1 - 28)

Description

Toggle between the Start screen and the foremost running app or the

Windows Desktop

Switch to the Windows desktop and launch Windows Explorer with

Computer displayed

Table 1 - 4 - Keyboard Shortcuts

Quick Start Guide

Function/Hot Key Indicators

Keys Function Keys Function

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.

Fn +

Fan Control Toggle -

Automatic Fan

Control / Full Power

Play/Pause (in Audio/Video Programs)

Fn +

Brightness Decrease/Increase

PC Camera

Power Toggle

Fn +

Touchpad Toggle

(Press a key to or use Touchpad to turn on)

Turn LCD Backlight Off

Mute Toggle

Sleep Toggle

Volume Decrease/Increase

Display Toggle

Table 1 - 5 - Function & Hot Key Indicators

Fn +

Airplane Mode

Toggle

Number Lock

Toggle

Scroll Lock

Toggle

Caps Lock

Toggle

Toggle Keyboard Illumination/Adjust

Brightness Level (*note that this is

applicable to illuminated keyboards only)

Control Center Toggle (see over)

Function/Hot Key Indicators 1 - 13



Control Center

Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.

Click on the power conservation modes to switch between Performance, Balanced or Energy Star modes. To remove the Power Conservation Modes screen just click in a blank area of the icon or press a key on the keyboard.

Click on the buttons (or just click and hold the mouse button) to adjust the slider for Brightness/Volume.

Click on Display Switch and click to choose a display mode from the menu.

Quick Start Guide

Control Center

When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch

Pad on/off (see Appendix B for full details).

in the notification area of the taskbar to toggle the Control Center on/off. The Con-

1 - 14 Control Center

Figure 1 - 6 - Control Center

Models A & B: Front & Left Views

Figure 1 - 7

Models A & B

Front & Left Views

1. LED Power Indicators

2. Multi-in-1 Card Reader

3. DC-In Jack

4. Vent/Fan Intake/ Outlet

5. External Monitor Port

6. RJ-45 LAN Jack

7. Combined eSATA/USB 3.0 Port

8. HDMI-Out Port

9. USB 3.0 Port



Multi-In-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RS MMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

USB 3.0 Port OR USB 2.0 Port

This model includes 3 * USB 3.0 ports (including one combo e-SATA/USB 3 .0 port) and 1* USB 2.0 port. USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

Quick Start Guide

Models A & B: Front & Left Views 1 - 15

Figure 1 - 8

Models C & D

Front & Left Views

1. LED Power Indicators

2. Multi-in-1 Card Reader

3. DC-In Jack

4. Vent/Fan Intake/ Outlet

5. External Monitor Port

6. RJ-45 LAN Jack

7. Combined eSATA/USB 3.0 Port

8. HDMI-Out Port

9. USB 3.0 Port



Multi-In-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RS MMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

USB 3.0 Port OR USB 2.0 Port

This model includes 3 * USB 3.0 ports (including one combo e-SATA/USB 3 .0 port) and 1* USB 2.0 port. USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

Quick Start Guide

Models C & D: Front & Left Views

1 - 16 Models C & D: Front & Left Views

Models A & B: Right & Rear Views

Figure 1 - 9

Models A & B

Right & Rear Views

1. Microphone-In Jack

2. Headphone-Out Jack

3. USB 2.0 Port

4. USB 3.0 Port

5. Optical Device Drive Bay (for CD/ DVD Device)

6. Security Lock Slot

7. Battery

W255EU



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

Quick Start Guide

Models A & B: Right & Rear Views 1 - 17

Figure 1 - 10

Models C & D

Right & Rear Views

1. Microphone-In Jack

2. Headphone-Out Jack

3. USB 2.0 Port

4. USB 3.0 Port

5. Optical Device Drive Bay (for CD/ DVD Device)

6. Security Lock Slot

7. Battery

W255EU



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

USB 3.0 Port OR USB 2.0 Port

This model includes 3 * USB 3.0 ports (including one combo e-SATA/USB 3.0 port) and 1* USB 2.0 port. USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

Quick Start Guide

Models C & D: Right & Rear Views

1 - 18 Models C & D: Right & Rear Views



Disk Eject Warning

Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.

CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”.



Changing DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click th e +

next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD Regional Codes” on page 2 - 5).

DVD region detection is device dependent, not OSdependent. You can select your module’s region code 5 times. The fifth selection is pe rmanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Quick Start Guide

Models C & D: Right & Rear Views 1 - 19

Figure 1 - 11

Models A & B

Bottom View

1. Battery

2. Component Bay

Cover

3. Vent/Fan Intake/

Outlet

4. Multi-in-1 Card

Reader

5. Speakers



CPU

The CPU is not a user serviceable part.



Overheating

To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.

Quick Start Guide

Models A & B: Bottom View

1 - 20 Models A & B: Bottom View

Models C & D: Bottom View

Figure 1 - 12

Models C & D

Bottom View

1. Battery

2. Component Bay

Cover

3. Vent/Fan Intake/

Outlet

4. Speakers



CPU

The CPU is not a user serviceable part.



Overheating

To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.

Quick Start Guide

Models C & D: Bottom View 1 - 21



Windows Versions

Note that the information included on the following pages is for Windows 8.1 only.

The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is provided on the De-

vice Drivers & Manual Disc with reference to

Windows 8.

Move the mouse to the bottom left

Start ScreenDesktop app

of the screen and right-click to access the menu.

Quick Start Guide

Windows 8.1 Control Panel

Throughout this manual you will see an instruction to open the Control Panel. R

ight-click the lower left hot corner to bring up the context menu (or use the Win-

dows Logo Key + X key combination)

Desktop app or Start screen.

and select Control Panel in both the

1 - 22 Windows 8.1 Control Panel

Figure 1 - 13 - Windows Context Menu

Right-click the Start button in the Desktop app (or use the Windows Logo Key



Display Most

Recently Used

Apps

If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app.

To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list.

Move the mouse to the bottom left of the screen

and right-click the Start button to access the menu.

+ X key combination) to bring up an advanced context menu of useful features

such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.

Figure 1 - 14 - Advanced Context Menu (Right-Click Start Button)

Quick Start Guide

Windows 8.1 Control Panel 1 - 23

Quick Start Guide

The Control Panel can be accessed in a number of ways in Windows 8.1.

•Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type

Control Panel and select it from the results to the left.

Figure 1 - 15 - Search (Control Panel)

• Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the top menu and select Open Control Panel from the ribbon.

Figure 1 - 16 - Open Control Panel (Computer)

1 - 24 Windows 8.1 Control Panel

Quick Start Guide

• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu.

Figure 1 - 17 - Settings Charms Bar (Desktop App Only)

• Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System).

Figure 1 - 18 - All Apps - Control Panel

Windows 8.1 Control Panel 1 - 25



Keyboard Shortcut to Control Panel

You can also use keyboard shortcuts to access the Contro l Pa nel. Press th e Win dows logo key an d X to b ring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.

Quick Start Guide

Right-click the Start button to bring up the menu and select Control Panel (see Figure 1 - 14 on page 1 - 23).

1 - 26 Windows 8.1 Control Panel

Quick Start Guide

Desktop App

Windows 8.1 Start Screen & Desktop

The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking

the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps.

Figure 1 - 19 - Windows Start Screen

Windows 8.1 Start Screen & Desktop 1 - 27

Click the arrow at the bottom of the screen to access All Apps

Quick Start Guide

Apps & Tiles

The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.

Accessing Pining/Unpinning All Apps

You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the Customize icon. Click the Customize icon to display all the installed

applications etc. Right-click any icon to bring up the menu at the bottom of the screen and you can then click the appropriate icon to pin the App to (or unpin from) the Start screen, or to the taskbar in the Desktop applica- tion (you can also open the app in a new window, run as administrator or open the file location).

Figure 1 - 20 - Customize Apps

1 - 28 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Move the mouse to the bottom left of the screen and click to switch back to the Start screen.

Desktop Application

When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click.

When you move to the lower left hot corner in the Start screen it will take you back to your most recently used app (if one is running).

Figure 1 - 21 - Desktop

Windows 8.1 Start Screen & Desktop 1 - 29

Move the mouse over a Charms Bar icon to activate the menu

Move the mouse to the top/lower right icons to activate the Charms Bar

Quick Start Guide

The Charms Bar

The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of

the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.

Figure 1 - 22 - Start Screen with Charms Bar

1 - 30 Windows 8.1 Start Screen & Desktop

Quick Start Guide



Charms Bar - TouchPad Access

To quick access the Charms Bar using the TouchPad:

1. Place your finger off the TouchPad (slightly to the right of the pad resting on the computer).

2. Move your finger across to the left on to the TouchPad.

3. The Charms Bar will then pop-up.

Charms Bar Items

• Search : You can search for any file, application, Apps and control panel settings with instantaneous

results.

•Share : This button is used to share information with people via mail or social networks.

•Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or click-

ing the bottom left of the screen).

• Devices : Click this button to change connected peripheral device settings e.g. an external display.

• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).

Figure 1 - 23 - Settings Menu

Windows 8.1 Start Screen & Desktop 1 - 31

Quick Start Guide

Windows 8.1 Taskbar

In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar is accessed from the Desktop application; if you are in the Start

screen you will need to switch to the Desktop. The taskbar is displayed at the bottom of the Desktop screen, and you can see the notification area (system

tray) of the taskbar in the bottom right of the screen. Some of the control panels and applications referred to during the course of this manual can be accessed from here.

Figure 1 - 24 - Desktop Taskbar & Notification Area (System Tray)

You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing

Pining/Unpinning All Apps” on page 1 - 28).

1 - 32 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Video Features

You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows when running the Desktop app (see “Desktop Application ” on page 1 - 29). It is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The

Charms Bar” on page 1 - 30).

To Configure Displays from Devices (Charms Bar):

1. Attach your display to the appropriate port, and turn it on.

2. Go the Charms Bar, select Devices.

3. Click Project (you may need to click Second Screen).

4. Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen

only.

Figure 1 - 25 - Devices (Project)

Video Features 1 - 33



Right-Click Desktop

App

1. You can right-click the desktop and select Screen reso- lution (Figure 1 -

26).

2. Use the dropbox to select the screen

Resolution

(Figure 1 - 26).

3. Click Advanced settings (Figure

1 - 26) to bring up the

Advanced properties tabs.

123

Quick Start Guide

To access Display (Control Panel) and Screen Resolution in Windows 8:

1. Go to the Control Panel.

2. Click Display (icon) - In the Appearance and Personalization category.

3. Adjust resolution.

Figure 1 - 26 - Screen Resolution

1 - 34 Video Features

Quick Start Guide

To access the Intel(R) HD Graphics Control Panel:

1. Click Advanced settings (Figure 1 - 26 on page 1 - 34) in the Screen Resolution control panel in Windows.

2. Click the Intel(R)... tab and click Graphics Properties (button) (Figure 1 - 27 on page 1 - 35) .

3. Right-click the desktop and select Graphics Properties from the menu.

4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.

Figure 1 - 27 - Intel Graphics Control Panel

Video Features 1 - 35

Quick Start Guide

To access the NVIDIA Control Panel:

1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 28).

2. Double-click the icon (Figure 1 - 28) in the Windows control panel.

Figure 1 - 28 - NVIDIA Control Panel

1 - 36 Video Features

Quick Start Guide

Charms Bar Desktop App Start Screen

Power Options

Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set- tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc.

Shut Down, Restart or Sleep (Charms Bar)

1. Go to the Charms Bar and click Settings.

2. Click Power .

3. Select Sleep, Shut Down or Restart.

Figure 1 - 29 - Shut Down/Restart

Power Options 1 - 37



Screen Resolution for Apps

(Windows 8.1)

The minimum resolution in which Apps will run is 1024x768. The minimum resolution required to support a ll the features of

Windows 8 (including multitasking with snap) is 1366x768. These specs are the minimum screen resolution that supports

all the features of Windows 8.1 on a useful physical size.

Quick Start Guide

Running Apps

To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements.

Screen Resolution Settings

1. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).

2. Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).

1 - 38 Running Apps

Figure 1 - 30 - Screen Resolution

Quick Start Guide

User Account Control Settings

If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below.

1. Open the Control Panel.

2. Click on User Accounts and then click on Change User Account Control settings (or click System and Security and click Change User Account Control Settings under Action Center).

3. If the slider is in the Never notify position, then the UAC is disabled.

4. To enable or turn on the UAC, move the slider to Always notify or Notify me when apps try to make changes

to my computer (default) position, and then click OK.

Figure 1 - 31 - User Account Control

Running Apps 1 - 39

Quick Start Guide

1 - 40

Features & Components

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components of the computer:

•Hard Disk Drive

• Optical (CD/DVD) Device

• Multi-In-1 Card Reader

• Touchpad/Clickpad and Buttons/Mouse

• Audio Features

Overview 2 - 1

Features & Components



Power Safety

Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.

Warranty Warning

Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.

Figure 2 - 1

Hard Disk Location

HDD Bay

HDD

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.

The hard disk is accessible from the bottom of your computer as seen below. For further details see “Upgrading the Hard Disk Drive” on page 6 - 8.

2 - 2 Hard Disk Drive

Features & Components



Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Win- dows. Click the Volume icon on the taskbar to check the setting (see

“Audio Features” on page 2 - 17).

Figure 2 - 2

Optical Device

123

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 3). Th e optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.

Optical (CD/DVD) Device 2 - 3

Features & Components



CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.

2 - 4 Optical (CD/DVD) Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Features & Components



DVD Region Note

DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Figure 2 - 3

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - Western Europe, Japan,

South Africa, Middle East & Egypt

• Region 3 - South-East Asia, T aiwan,

South Korea, The Philippines, Indonesia, Hong Kong

• Region 4 - South & Central Amer-

ica, Mexico, Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern

Europe, India & Most of Africa

• Region 6 - China

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.

3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control p anel to allow you to adjust the regional code.

Optical (CD/DVD) Device 2 - 5

Features & Components

Figure 2 - 4

Front View

1. Card Reader

• MMC (MultiMedia Card) / RS MMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

Models A & B

Models C & D

Multi-In-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see

“CardReader” on page 4 - 7.

Note: Some of these cards require PC adapters that are usually supplied with the cards.

2 - 6 Multi-In-1 Card Reader

Features & Components

Touchpad/Clickpad and Buttons/Mouse

The touchpad/clickpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The touchpad/clickpad buttons function in much the same way as a two-button mouse. Install the driver as instructed in “Touchpad” on page 4 - 8 and the appropriate application software version will be installed for your computer.

Touchpad/Clickpad and Buttons/Mouse 2 - 7

Features & Components



Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.

Figure 2 - 5

Mouse Properties

(ELAN tab) & Taskbar Icon

Elan TouchPad

Once you have installed the touchpad driver (see “Touchpad” on page 4 - 8) you can configure the functions by double-clicking the touchpad driver icon in the notification area of the taskbar (or from Options in the ELAN tab in the Mouse control panel in Windows). You may then configure the gestures and options to your preferences.

2 - 8 Touchpad/Clickpad and Buttons/Mouse

The Elan Smart-Pad control panel allows you to use a specific gesture (action) on

Figure 2 - 6

Smart-Pad Control

Panel (Button)

the surface of the touchpad to perform specific actions to manipulate documents, objects and applications.

Click the menu tabs (One-finger, Multi-finger or Additional) and then the function button on the left to access the Configuration controls in the right panel. Click the check box to Enable most of the controls and click Apply to save the settings. Click the close icon or Yes to close the control panel.

Features & Components

Touchpad/Clickpad and Buttons/Mouse 2 - 9

Features & Components

Figure 2 - 7

Smart-Pad Control

Panel with

Function

Description

Click the Function Description button to get a detailed description of any function.

Click the Default button to set any of the functions to the default setting.

2 - 10 Touchpad/Clickpad and Buttons/Mouse

Features & Components

Figure 2 - 8

Tapping

Figure 2 - 9

Button

One-Finger

Tapping

One-Finger tapping is equivalent to clicking the left mouse button to perform a point/click/select function.

Button

The left and right touchpad buttons may be configured to perform any action listed in the Button drop-down menu.

Touchpad/Clickpad and Buttons/Mouse 2 - 11

Features & Components

Figure 2 - 10

Drag and Drop

Figure 2 - 11

Edge Scroll

Drag and Drop

You can select the different drag and drop methods from the menu provided. The object can be released when you lift the finger off the touchpad, when you tap again or after a set time delay.

Edge Scroll

Enable Vertical or Horizontal Scroll from this menu. You can configure the width of the scrollable area by adjusting the slider accordingly. To scroll vertically, tap the right edge of the touchpad and drag the finger up and down. To scroll horizontally, tap the bottom edge of the touchpad and drag your finger left or right.

2 - 12 Touchpad/Clickpad and Buttons/Mouse

Edge Swipe

Figure 2 - 12

Edge Swipe

Enable Edge Swipe to use a single finger to scroll from the edges of the touchpad to perform the designated function in Windows 8.

Features & Components

Touchpad/Clickpad and Buttons/Mouse 2 - 13

Features & Components

Figure 2 - 13

Zooming

Figure 2 - 14

Scrolling

Multi-Finger

Zooming

Place two fingers on the touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.

Scrolling

The Two-Finger scrolling feature works in most scrollable windows an d allows you to scroll horizontally and vertically. Tap the pad surface and slide both fingers in the direction required (vertically or horizontally as long as the option is selected).

Note that the scrolling direction is opposite to that of a standard mouse wheel configuration.

2 - 14 Touchpad/Clickpad and Buttons/Mouse

Rotation

Figure 2 - 15

Rotation

Figure 2 - 16

Swipe Page

You can rotate objects by using a two-finger gesture. Touch and rotate using two fingers on the pad in the direction required. Alternatively place a finger down on the pad and rotate the other finger around it in a circular motion (clockwise or counterclockwise).

Three Finger Swipe

This gesture is used to activate a Page Up/Page Down operation. Swipe three fingers quickly to the left to go to the previous page, or to the right to go to the next page. After you release your fingers from the pad the page changes, and make sure to lift your fingers immediately after the page change.

Features & Components

Touchpad/Clickpad and Buttons/Mouse 2 - 15

Features & Components

Figure 2 - 17

Palm Tracking

Figure 2 - 18

Sensitivity

Additional

Palm Tracking

This feature helps guard against accidental contact such as palms resting on the pad. Use the slider to adjust the sensitivity of the feature as appropriate.

Sensitivity

Adjust the level of finger pressure required for the cursor to respond from this menu.

2 - 16 Touchpad/Clickpad and Buttons/Mouse

Features & Components



Sound Volume

Adjustment

The sound volume level is set using the volume control on the Windows desktop (and the vol-

ume function keys F5/ F6 on the computer).

Click the volume icon in the taskbar to check the setting.

Figure 2 - 19

VIA HD Audio Deck

Click Expert Mode to access the Advanced menus

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel .

The volume may also be adjusted by means of the Fn + F5/F6 key combination.

Audio Features 2 - 17

Features & Components



Syncing Left & Right

Volume

Balance

If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the

VIA HD Audio Deck in Expert Mode.

Click Speaker in VIA HD Audio Deck (in Expert Mode) and click the Sync Left and Right volume

button (see left). You can then adjust the volume sliders independently (this setting also controls the Balance setting in the Windows Sound control panel).

Figure 2 - 20

VIA HD Audio Deck

(Expert Mode)

Note that to adjust the Left & Right volume balan ce independently click t he Sync Left and Right Volume icon (it should be faded) and adjust the slider as required.



Sound Blaster Cinema Audio

Note that you will need to install the Sound Blaster Cinema audio application in order to get maximum audio performance. See “Sound Blaster Cinema EQ” on page 7 - 31

Expert Mode will allow you to access more advanced configuration menus for

Speaker and Microphone.

2 - 18 Audio Features

Chapter 3: Power Management



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows

8.1 OS.)

Power Options

Power management in Windows is configured from Power Options (Hardware and Sound), which can be accessed from the Con- trol Panel (see page 1 -

14).

Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers:

• The Power Sources

• Turning On the Computer

• Shutting the Computer Down

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.

Overview 3 - 1

Power Management



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.

1. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter (make sure you use the adapter when first setting up the computer, as to safeguard the computer during shipping the battery will be locked to not power the system until first connected to the AC/DC adapter).

2. Raise the lid/LCD to a comfortable viewing angle.

3. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “Battery FAQ” on page 3 - 18).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 14.

3 - 2 The Power Sources

Turning On the Computer



Power Button as Stand by or Hibernate Button

You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring

the Power Buttons” on page 3 - 9 for details).

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.

Power Management

Turning On the Computer 3 - 3

Power Management

Figure 3 - 1

Shut Down/Restart

Charms Bar Desktop App Start Screen

Shutting the Computer Down

Note that you should always shut your computer down by choosing the Shut down

command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen

to bring up the menu). You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If

you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep

to the Power Menu” on page 3 - 10.

3 - 4 Shutting the Computer Down

Power Plans



Resuming

Operation

See Table 3 - 1, on

page 3 - 11 for informa-

tion on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Figure 3 - 2

Power Plan

Advanced Settings

The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.

Power Management

Power Plans3-5

Power Management

Figure 3 - 3

Power Plans

Click to Show/Hide additional power plans

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

3 - 6 Power Plans

Power-Saving States



Wake On LAN

Support

(Windows 8)

Wake-On-LAN is only supported from Sleep or

Hibernate states in Windows 8.

If you require your computer to wake up from network activity in Windows 8 then make sure that the computer is either in Sleep or Hiber- nate.

Wake-On-LAN is not supported from Shutdown states in Win- dows 8.

You can use power-saving states to stop the computer’s operation and restart where you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file( s) you last used.

If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.

Power Management

To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power

Menu” on page 3 - 10.

Power-Saving States 3 - 7

Power Management

Figure 3 - 4

Power Menu

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves

all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.

3 - 8 Power-Saving States

Configuring the Power Buttons



Password

Protection

It is recommended that you enable a password on wake up in order to protect your data.

However you can disable this setting from the Power Options menu by clicking Require a

password on wakeup

in the left menu, and selecting the options (click

Change settings that are currently unavailable).

Figure 3 - 5

Power Options

Define Power

Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.

Power Management

Configuring the Power Buttons 3 - 9

Power Management

Figure 3 - 6

Power Options

Define Power

Buttons - Shutdown

Settings

Adding Hibernate/Sleep to the Power Menu

Add Hibernate/Sleep to the Power Menu as follows.

1. Go to the Power Options (Hardware and Sound) control panel.

2. Click “Change settings that are currently unavailable” .

3. Click Choose what the power buttons do.

4. Click to put a check in the Hibernate/Sleep box under Shutdown settings.

5. Click Save Changes and close the control panel.

3 - 10 Configuring the Power Buttons

Resuming Operation

Table 3 - 1

Resuming

Operation



Closing the Lid

If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).

You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).

Power Status

Power Off Off Press the Power Button

Icon Color

To Resume

Power Management

Sleep Blinking Green

Press the Sleep Button (Fn + F4 Key Combo)

Off (battery)

Hibernate

Orange (AC/DC adapter)

Display Turned Off Green Press a Key or Move the Mouse/Touchpad

Press the Power Button

Configuring the Power Buttons 3 - 11

Power Management



Power Conservation

Modes

The Energy Star setting will result in maximum power saving, but with the possible loss of some performance.

Setting the mode to Bal- ance will give power saving matched with performance.

Performance will give optimum computer performance but with less power conservation.

Figure 3 - 7

Control Center



Energy Star

Display Sleep Mode

Note that the Energy Star setting will put the display into sleep after no more than 15 minutes of user inactivity.

Power Conservation Modes

This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center:

1. Press the Fn + Esc key combination to toggle the Control Center on/off.

2. Click either the Performance, Balanced or Energy Star button.

3. Click in a blank area of the icon or press a key on the keyboard to exit Power

Conservation Mode without making any changes.

3 - 12 Configuring the Power Buttons

Clevo W650SF, W650SJ, W670SFQ User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Chapter 1: Quick Start Guide

Overview

Advanced Users

Beginners and Not-So-Advanced Users

Warning Boxes

Not Included

System Startup

System Software

Model Differences

Models A & B: LCD Panel Open

Models C & D: LCD Panel Open

LED Indicators

Keyboard - Models A & B

Keyboard - Models C & D

Keyboard Shortcuts

Function/Hot Key Indicators

Control Center

Models A & B: Front & Left Views

Models C & D: Front & Left Views

Models A & B: Right & Rear Views

Models C & D: Right & Rear Views

Models A & B: Bottom View

Models C & D: Bottom View

Windows 8.1 Control Panel

Windows 8.1 Start Screen & Desktop

Apps & Tiles

Desktop Application

The Charms Bar

Windows 8.1 Taskbar

Video Features

Power Options

Running Apps

Chapter 2: Features & Components

Overview

Hard Disk Drive

Optical (CD/DVD) Device

Loading Discs

Handling CDs or DVDs

DVD Regional Codes

Multi-In-1 Card Reader

Touchpad/Clickpad and Buttons/Mouse

One-Finger

Multi-Finger

Additional

Audio Features

Chapter 3: Power Management

Overview

The Power Sources

AC/DC Adapter

Battery

Turning On the Computer

Shutting the Computer Down

Power Plans

Power-Saving States

Sleep

Hibernate

Shut down

Configuring the Power Buttons

Resuming Operation

Power Conservation Modes