Clevo W650RC1 User guide

V16.1.00

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©May 2016

Trademarks

Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

ErP Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:

• Off Mode < 0.5W

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc ed radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interfer ence that may cause undesired operation of the

device.

FCC RF Radiation Exposure Statement:



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit as follows:

•

For Models A & B Design I Series

AC/DC Adapter.

- AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19V, 4.74A (90 Watts) minimum

For Models A & B D esign II Series

•

AC/DC Adapter.

This Computer’s Optical Device is a Laser Class 1 Product

- AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19.5V, 6.15A (

120

W atts) minimum

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive heat or direct sunlight.

Do not leave it in a place where foreign matter or moisture may affect the system.

Don’t use or store the computer in a humid environment.

Do not place the computer on any surface that will block the Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

5. Take care when using peripheral devices.

Use only approved brands of peripherals.

VIII

Do not disassemble the computer by yourself.

Unplug the power cord befor e attaching peripheral devices.

Perform routine maintenance on your computer.

Servicing



Bottom Cover Removal Warning

Users should not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your distributor/supplier for further information.

Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

Preface



Power Safety Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).

You must also remove your battery in order to prevent accidentally turning the machine on.

Before removing the battery disconnect the AC/DC adapter from the computer.

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the powe r cord, be sure t o disconnect it by the plug head, not by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.

• If you are working in areas of low temperature use the AC/DC adapter to power the computer.

See also the general battery precautionary information overleaf for further information.

Preface



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

General Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

XII

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Cleaning Instructions

(For Computer Models Supplied with Light Blue Cleaning Cloth) Some computer models in this series come supplied with a light blue cleaning cloth. To clean the computer case with this cloth follow the instructions below:

1. Power off the computer and peripherals.

2. Disconnect the AC/DC adapter from the computer.

3. Use a little water to dampen the cloth slightly.

4. Clean the computer case with the cloth.

5. Dry the computer with a dry cloth, or allow it time to dry before turning on.

6. Reconnect the AC/DC adapter and turn the computer on.

XIII

Preface



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

Travel Considerations

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -

ware and software. Make sure your “papers” are handy.

XIV

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.

XVI

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier.

XVII

Preface

XVIII

Preface

Contents

Notice .............................................................................................................................................................I

ErP Off Mode Power Consumption Statement: ...........................................................................................II

FCC Statement ............................................................................................................................................IV

FCC RF Radiation Exposure Statement: .....................................................................................................V

Instructions for Care and Operation ......................................................................................................... VII

Servicing .....................................................................................................................................................IX

Power Safety ................................................................................................................................................X

Polymer Battery Precautions ......................................................................................................................XI

General Battery Precautions ..................................................................................................................... XII

Cleaning ...................................................................................................................................................XIII

Cleaning Instructions ...............................................................................................................................XIII

Travel Considerations ..............................................................................................................................XIV

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Startup ...........................................................................................................................................1-4

System Software ........................................................................................................................................1-5

XIX

Preface

Model Differences .....................................................................................................................................1-6

System Map: LCD Panel Open - Model A ................................................................................................1-7

System Map: LCD Panel Open - Model B ................................................................................................1-8

LED Indicators ...........................................................................................................................................1-9

Keyboard - Model A ................................................................................................................................1-10

Keyboard - Model B ................................................................................................................................1-11

Keyboard Shortcuts .................................................................................................................................1-12

Keyboard Application Settings ................................................................................................................1-13

Function/Hot Key Indicators ...................................................................................................................1-14

Control Center .........................................................................................................................................1-15

Flexikey® Application ............................................................................................................................1-16

Flexikey® Application Features: .............................................................................................................1-17

System Map: Front & Left Views - Model A ..........................................................................................1-18

System Map: Front & Left Views - Model B ..........................................................................................1-19

System Map: Right & Rear Views - Model A .........................................................................................1-20

System Map: Right & Rear Views - Model B .........................................................................................1-21

System Map: Bottom View - Model A ....................................................................................................1-23

System Map: Bottom View - Model B ....................................................................................................1-24

Windows 10 Start Menu ..........................................................................................................................1-25

Right-Clicking the Windows Logo In Start Menu ..................................................................................1-26

Start Menu Apps & Tiles .........................................................................................................................1-27

Windows 10 Control Panel ......................................................................................................................1-29

Preface

Settings ....................................................................................................................................................1-30

Windows 10 Taskbar ...............................................................................................................................1-31

Video Features .........................................................................................................................................1-32

Microsoft Hybrid Graphics ......................................................................................................................1-32

Power Options .........................................................................................................................................1-38

Features & Components

Overview ....................................................................................................................................................2-1

Hard Disk Drive/Solid State Drive ............................................................................................................2-2

Optical (CD/DVD) Device ........................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-In-1 Card Reader .............................................................................................................................2-6

Touchpad/Clickpad and Buttons/Mouse ....................................................................................................2-7

Gestures and Device Settings ....................................................................................................................2-9

Audio Features .........................................................................................................................................2-14

Setup for Audio Recording ......................................................................................................................2-15

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

XXI

Preface

Battery ........................................................................................................................................................3-2

Turning On the Computer ..........................................................................................................................3-3

Shutting the Computer Down ....................................................................................................................3-4

Power Plans ...............................................................................................................................................3-5

Power-Saving States ..................................................................................................................................3-7

Sleep ..........................................................................................................................................................3-7

Hibernate ....................................................................................................................................................3-8

Shut down ..................................................................................................................................................3-8

Configuring the Power Buttons .................................................................................................................3-9

Resuming Operation ................................................................................................................................3-11

Power Conservation Modes .....................................................................................................................3-12

Settings Menu Power Controls ................................................................................................................3-14

Battery Information .................................................................................................................................3-17

Battery Power ..........................................................................................................................................3-17

Conserving Battery Power .......................................................................................................................3-18

Battery Life ..............................................................................................................................................3-19

New Battery .............................................................................................................................................3-19

Recharging the Battery with the AC/DC Adapter ...................................................................................3-19

Proper handling of the Battery Pack ........................................................................................................3-20

Battery FAQ .............................................................................................................................................3-21

Removing the Battery ..............................................................................................................................3-25

XXII

Preface

Drivers & Utilities

What to Install ............................................................................................................................................4-1

Module Driver Installation ........................................................................................................................4-1

Driver Installation ......................................................................................................................................4-2

Updating/Reinstalling Individual Drivers ..................................................................................................4-5

User Account Control ................................................................................................................................4-6

Windows Security Message .......................................................................................................................4-6

New Hardware Found ................................................................................................................................4-6

Driver Installation Procedure .....................................................................................................................4-7

Chipset .......................................................................................................................................................4-7

Video (VGA) .............................................................................................................................................4-7

NVIDIA Video (VGA) ..............................................................................................................................4-7

LAN ...........................................................................................................................................................4-7

Card Reader ...............................................................................................................................................4-7

Touchpad ...................................................................................................................................................4-8

Airplane .....................................................................................................................................................4-8

Control Center ...........................................................................................................................................4-8

MEI Driver .................................................................................................................................................4-8

Audio .........................................................................................................................................................4-8

Optional Drivers ........................................................................................................................................4-9

XXIII

Preface

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Setup Utility ........................................................................................................................................5-2

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

Setup Screens .............................................................................................................................................5-4

Main Menu .................................................................................................................................................5-5

System Time & Date (Main Menu) ...........................................................................................................5-5

SATA Port # (Main Menu) ........................................................................................................................5-6

OffBoard SATA/NVme Controller Configuration (Main Menu) .............................................................5-6

CPU/ ME FW Version / System/ Extended Memory: (Main Menu) ........................................................5-6

MB Series / BIOS Revision / KBC/EC firmware Revision / MAC Address: (Main Menu) .....................5-6

Advanced Menu .........................................................................................................................................5-7

Advanced Chipset Control (Advanced Menu) ..........................................................................................5-7

FlexiCharger (Advanced Menu > Advanced Chipset Control) .................................................................5-8

GPU Performance Scaling (Advanced Menu > Advanced Chipset Control) ............................................5-8

SATA Mode (Advanced Menu) ................................................................................................................5-9

Boot Logo (Advanced Menu) ....................................................................................................................5-9

Power On Boot Beep (Advanced Menu) ...................................................................................................5-9

Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9

Security Menu ..........................................................................................................................................5-10

XXIV

Preface

Set Supervisor Password (Security Menu) ..............................................................................................5-10

Set User Password (Security Menu) ........................................................................................................5-11

Password on boot: (Security Menu) ........................................................................................................5-11

Secure Boot Control (Security Menu) .....................................................................................................5-12

TPM Configuration (Security Menu) ......................................................................................................5-13

Boot Menu ...............................................................................................................................................5-14

Boot Option Priorities (Boot Menu) ........................................................................................................5-15

UEFI Boot (Boot Menu) ..........................................................................................................................5-15

Exit Menu ................................................................................................................................................5-16

Modules & Options

Overview ....................................................................................................................................................6-1

Wireless LAN Module ...............................................................................................................................6-2

3rd Party 802.11b/g/n Driver Installation ..................................................................................................6-3

Intel® WLAN Driver Installation ..............................................................................................................6-3

WLAN Configuration in Windows 10 ......................................................................................................6-4

Bluetooth Combo Module .........................................................................................................................6-7

3rd Party Bluetooth (V4.0) Combo Driver Installation .............................................................................6-8

Intel Bluetooth Combo Driver Installation ................................................................................................6-8

Bluetooth Configuration in Windows ........................................................................................................6-9

To Make your Computer Discoverable to Bluetooth Devices .................................................................6-11

Intel® Rapid Storage Technology ...........................................................................................................6-12

XXV

Preface

IRST Driver Installation ..........................................................................................................................6-12

Sound Blaster Cinema 2 ..........................................................................................................................6-13

Sound Blaster Cinema 2 Installation .......................................................................................................6-13

Sound Blaster Cinema 2 Application ......................................................................................................6-14

Sound Blaster Cinema 2 SBX Pro Studio ................................................................................................6-18

PC Camera Module ..................................................................................................................................6-23

Camera App .............................................................................................................................................6-24

Taking Pictures/Capturing Video ............................................................................................................6-26

Trusted Platform Module .........................................................................................................................6-28

Enabling & Managing TPM ....................................................................................................................6-29

TPM Management in Windows ...............................................................................................................6-30

TPM Actions ............................................................................................................................................6-32

3G/4G Module .........................................................................................................................................6-34

3G/4G Configuration in Windows 10 .....................................................................................................E-37

Troubleshooting

Overview ....................................................................................................................................................7-1

Basic Hints and Tips ..................................................................................................................................7-2

Backup and General Maintenance .............................................................................................................7-3

Viruses .......................................................................................................................................................7-4

Upgrading and Adding New Hardware/Software ......................................................................................7-5

Problems and Possible Solutions ...............................................................................................................7-7

XXVI

Preface

Resolving the “Can’t connect to this network” issue with the 3G/4G Module .......................................7-15

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Notebook Ports and Jacks .........................................................................................................................A-2

Control Center & Flexikey®

Overview ...................................................................................................................................................B-1

Flexikey® Application .............................................................................................................................B-8

Profiles ......................................................................................................................................................................B-8

Flexikey® Application Features ...............................................................................................................B-9

Keyboard and Mouse Settings ................................................................................................................B-10

Enabling or Disabling Flexikey® ...........................................................................................................B-11

Keyboard Settings ...................................................................................................................................B-12

Mouse Settings ........................................................................................................................................B-13

Keyboard Settings - Express Key ...........................................................................................................B-14

Keyboard Settings - Launch App ...........................................................................................................B-18

Keyboard Settings - Express Text ..........................................................................................................B-20

Keyboard Settings - Disable ...................................................................................................................B-22

Mouse Settings - Express Key ................................................................................................................B-23

Mouse Settings - Launch App ................................................................................................................B-25

Mouse Settings - Express Text ...............................................................................................................B-27

Mouse Settings - Disable ........................................................................................................................B-29

XXVII

Preface

Statistics ..................................................................................................................................................B-30

Video Driver Controls

Video Drivers ............................................................................................................................................C-1

Video (VGA) ............................................................................................................................................C-1

NVIDIA Video (VGA) .............................................................................................................................C-1

Dynamic Video Memory Technology ......................................................................................................C-2

Microsoft Hybrid Graphics .......................................................................................................................C-3

Intel® HD Graphics Control Panel ...........................................................................................................C-5

Display Devices & Options ....................................................................................................................C-19

Attaching Other Displays .......................................................................................................................C-20

Configure Other Displays Using Project ................................................................................................C-23

You can configure attached displays from Project. ................................................................................C-23

Configuring an External Display In Windows .......................................................................................C-24

NVIDIA Control Panel ...........................................................................................................................C-27

Customization Options ...........................................................................................................................C-29

Set PhysX® Configuration .....................................................................................................................C-33

NVIDIA GeForce Experience ................................................................................................................C-34

NVIDIA GeForce Experience - BatteryBoost ........................................................................................C-36

NVIDIA GeForce Experience - ShadowPlay .........................................................................................C-37

HDMI Audio Configuration ...................................................................................................................C-38

Wireless Display .....................................................................................................................................C-41

XXVIII

Preface

Wireless Display Configuration .............................................................................................................C-42

Specifications

Processors .................................................................................................................................................D-2

Core Logic ................................................................................................................................................D-2

Display ......................................................................................................................................................D-2

Memory .....................................................................................................................................................D-2

Video Adapter - Designs I & II Only .......................................................................................................D-2

Storage ......................................................................................................................................................D-2

Audio ........................................................................................................................................................D-3

Keyboard & Pointing Device ....................................................................................................................D-3

Interface ....................................................................................................................................................D-3

Card Reader ..............................................................................................................................................D-3

Slots ..........................................................................................................................................................D-3

Communication .........................................................................................................................................D-4

Battery .......................................................................................................................................................D-4

Power ........................................................................................................................................................D-4

Power Management ..................................................................................................................................D-4

Indicators ..................................................................................................................................................D-4

BIOS .........................................................................................................................................................D-4

Security .....................................................................................................................................................D-4

Features .....................................................................................................................................................D-4

XXIX

Preface

Operating System ......................................................................................................................................D-4

Environmental Spec ..................................................................................................................................D-5

Dimensions & Weight ..............................................................................................................................D-5

XXX

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, card reader), Touchpad/Mouse and Audio.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth & WLAN Combo, Intel Technology, Sound Blaster Cinema and 3G/4G modules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.

• Appendix B Information on Control Center.

• Appendix C Information on the video driver controls.

• Appendix D The computer’s specification.

Overview 1 - 1



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in the Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you); refer to

Chapter 4 for installation instructions.

Ports and Jacks

See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Not Included

Operating Systems (e.g. Windows 10) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.

Overview 1 - 3

130°



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command in Windows. This will help prevent hard disk or system problems.

Quick Start Guide

System Startup

1. Remove all packing materials.

2. Place the computer on a stable surface.

3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

4. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter.

5. Use one hand to raise the

hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).

lid/LCD to a comfortable viewing angle (

do not exceed 130 degrees

);

use the other

Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In

1 - 4 System Startup

System Software



Windows OS

Note that the information included on the following pages is for Windows 10 only. In order to run Windows 10 (64-bit) your computer requires a minimum 2GB of system memory (RAM).

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 10 (64-bit) operating system is supported.

Quick Start Guide

System Startup 1 - 5

Quick Start Guide

Model Differences

This notebook series includes two different model types (and two design styles for each model) that mainly d iffer as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual (also see Appendix D for details of supported processors etc.).

Model A Model B

Feature

Design I Design II Design I Design II

Display

Video

Controller

3G/4G

Module

Power Supply

15.6” / 39.62cm HD (1366 * 768) / FHD (1920 * 1080), 16:9

Intel® Integrated GPU (Intel®

HD Graphics 530) and

NVIDIA® GeForce

Video

Full Range AC/DC Adapter

AC input 100 - 240V, 50 - 60Hz,

DC Output 19V, 4.74A

(90 Watts)

1 - 6 System Startup

(3.8mm thick) Backlit Panel

Intel® Integrated GPU (Intel®

HD Graphics 530) and

940MX

NVIDIA® GeForce GTX

950M Video

Supported Not Supported

Full Range AC/DC Adapter

AC input 100 - 240V, 50 - 60Hz,

DC Output 19.5V, 6.15A

(120 Watts)

17.3" / 43.94cm HD+ (1600 * 900) / FHD (1920 * 1080), 16:9

Intel® Integrated GPU (Intel®

HD Graphics 530) and

NVIDIA® GeForce

Video

Full Range AC/DC Adapter

AC input 100 - 240V, 50 - 60Hz,

DC Output 19V, 4.74A

(90 Watts)

Table 1 - 1 - Model Differences

Backlit Panel

940MX

Intel® Integrated GPU (Intel®

HD Graphics 530) and

NVIDIA® GeForce GTX

950M Video

Full Range AC/DC Adapter

AC input 100 - 240V, 50 - 60Hz,

DC Output 19.5V, 6.15A

(120 Watts)

System Map: LCD Panel Open - Model A

Figure 1 - 2

LCD Panel Open -

Model A

1. Built-in PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Power Button

6. LED Indicators (Caps, Num & Scroll Lock)

7. Keyboard

8. Touchpad & Buttons

Touchpad Buttons (valid operation area)

Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines indicated on the right. See “Touchpad/Clickpad Sensitivity” on page 2 - 7.



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the 3G/4G/WLAN/ Bluetooth module(s) are OFF if you are using the computer aboard aircraft.

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/ Off, and check the LED indicator for the power status (see Table 1 - 5, on

page 1 - 14/ Table 1 - 2, on page 1 - 9).

Quick Start Guide

System Map: LCD Panel Open - Model A 1 - 7

Figure 1 - 3

LCD Panel Open -

Model B

1. Built-in PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Power Button

6. LED Status Indicators (Caps, Num & Scroll Lock)

7. Keyboard

8. Click Pad & Buttons

Note that the click pad has a defined valid operational area of sensitivity indicated within the sensor area of the illustration below. See “Touchpad/

Clickpad Sensitivity” on page 2 - 7.



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the WLAN/Bluetooth module(s) are OFF if you are using the computer aboard aircraft.

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/ Off, and check the LED indicator for the power status (see Table 1 - 5, on page 1

- 14/ Table 1 - 2, on page 1

- 9).

Quick Start Guide

System Map: LCD Panel Open - Model B

1 - 8 System Map: LCD Panel Open - Model B

Quick Start Guide

LED Indicators

The LED indicators on the computer display helpful information about the current status of the computer.

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking Green

Orange The Battery is Charging

Green The Battery is Fully Charged

Blinking Orange

Green Hard Disk Activity

Green

Table 1 - 2 - LED Power Indicators

The Computer is in Sleep

Mode

The Battery Has Reached

Critically Low Power Status

Airplane Mode is ON (the WLAN/Bluetooth & 3G/4G

Modules are OFF)

Icon Color Description

Green Number Lock Activated

Green

Green Caps Lock Activated

Scroll Lock Activated (to activate

press Fn & Scr Lk)

Table 1 - 3 - LED Status Indicators

LED Indicators 1 - 9



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.

NumLk & ScrLk

Hold down the Fn Key and either NumLk or ScrLk to enable number or scroll lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk & ScrLk Keys

Fn Key

Keypad

Windows Logo Key

Menu/Application Key



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Quick Start Guide

Keyboard - Model A

The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.

Figure 1 - 4 - Keyboard - Model A

1 - 10 Keyboard - Model A

Keyboard - Model B



Other Keyboards

NumLk & ScrLk

Hold down the Fn Key and either NumLk or ScrLk to enable number or scroll lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk & ScrLk Keys

Fn Key

Keypad

Windows Logo Key

Menu/Application Key



Special Characters

The keyboard has an embedded numerical keypad for easy numeric data input, and function keys to change operational features instantly.

Figure 1 - 5 - Keyboard - Model B

Quick Start Guide

Keyboard - Model B 1 - 11



Windows Logo

Keyboard Shortcut

Use the Windows logo key + D key com- bination to switch between the Start screen and Windows Desktop.

Menu/Application

Keyboard Shortcut

When the Desktop app is running you can use the Menu/Application key on the keyboard to display the context menu as per a mouse right-click.

Quick Start Guide

Keyboard Shortcuts

The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in

Windows 10

1 - 12 Keyboard - Model B

Windows Logo

Key +

Tap Winkey Toggle the Start menu

A Open the Action Center B Select the Taskbar Notification Area C Launch Cortana (in listening mode) D Toggle the Desktop E Launch File Explorer (Quick Access tab)

+ Number (1, 2, etc) Launch an application from the taskbar (numbered from left to right)

Table 1 - 4 - Keyboard Shortcuts

Description

Quick Start Guide

Right-click and select Keyboard Settings.

Keyboard Application Settings

(Model B Factory Option) If your Model B computer includes an illuminated keyboard, you will need to install the keyboard Control Cen- ter application driver (see “Control Center” on page 4 - 8) and you can then select the type of keyboard as ap- propriate for your model’s configuration (you can only select keyboards supported by your system). After the driver has been installed, and the system restarts, the control panel below will pop-up to allow you to select the illuminated white keyboard for your system. Click Save to retain the setting chosen.

If you wish to change the setting at any time then right-click on the Control Center icon and select Key- board Settings to return to the keyboard select control panel.

Figure 1 - 6 - Keyboard Settings for Illuminated Keyboard Option

Keyboard Application Settings 1 - 13

Quick Start Guide

Function/Hot Key Indicators

Keys Function Keys Function

Fn +

Play/Pause (in Audio/Video Programs)

TouchPad Toggle

(Press a key to or use TouchPad to turn on)

Toggle Off/High/Low Keyboards Designs

Turn LCD Backlight Off

Mute Toggle Fn + NumLk Number Lock Toggle

Backlight Keyboard

(Illuminated

Only)

Volume Decrease/Increase Caps Lock Caps Lock Toggle

Display Switch Menu

Brightness Decrease/Increase

Table 1 - 5 - Function Keys & Visual Indicators

1 - 14 Function/Hot Key Indicators

Fn +

Fn + ScrLk Scroll Lock Toggle

Fn +

PC Camera Power Toggle

Airplane Mode Toggle

Fan Control Toggle between

Automatic Fan Control / Full Power

Control Center Toggle (see over)

Sleep Toggle

Quick Start Guide



Control Center Access

To run the Control Center press the Fn + Esc key combination, or doubleclick the icon

in the notification area of the taskbar.

Close the Control Center by clicking the close icon in the top right of the panel (move the cursor onto the top right corner of the panel to highlight it).

Control Center

When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch

Pad on/off (see Appendix B for full details).

in the notification area of the taskbar to toggle the Control Center on/off. The Con-

Figure 1 - 7 - Control Center

Control Center 1 - 15

Flexikey® Enabled

Flexikey® Disabled

Quick Start Guide

Flexikey® Application

The Flexikey® application is a quick hotkey configuration application, which allows you to assign a single key to launch multiple key combinations, or to launch programs and applications, to create text macros and to disable certain keys. The application can also be used to configure the mouse buttons to create hotkeys for gaming etc. All the configuration settings are retained under (up to12) profiles to which the settings are applied. Click Flexikey® in the Gaming section of the Control Center, or the click the icon in the notification area of the taskbar, to launch the application (see Appendix B for full details).

1 - 16 Flexikey® Application

Figure 1 - 8 - Flexikey® Hotkey Application

Quick Start Guide

Flexikey® Application Features:

For full details see “Flexikey® Application” on page B - 8.

• EXPRESS KEY - This feature allows you to configure a single key (or mouse click) to send multiple key

combinations, or to create more useful shortcut keys This is useful in gaming or when using applications which have a complex set of keyboard shortcuts.

• LAUNCH APP - This simply assigns single keys (or mouse clicks) to launch any program’s or applica-

tion’s executable file.

• EXPRESS TEXT - With this you can assign single keys (or mouse clicks) to send commonly used strings

of text.

• DISABLE - Use this function to disable any keyboard keys or mouse buttons.

• STATISTICS - Use this to quickly record keys in use in any application, and to disable unused keys.

Flexikey® Application 1 - 17

Figure 1 - 9

Front & Left Views

Model A

1. LED Power Indicators

2. Multi-in-1 Card Reader

3. DC-In Jack

4. Vent/Fan Intake/ Outlet

5. External Monitor Port

6. RJ-45 LAN Jack

7. 2 * USB 3.0 Ports (USB 3.1 Gen 1)

2 * USB 3.1 Ports (USB 31. Gen 2 Type A) (Factory Option)

8. HDMI-Out Port



Multi-In-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RS MMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

USB 3.0 / 3.1 Port OR USB 2.0 Port

This model includes 3 * USB 3.0 ports (USB 3.1 Gen 1 ports) and 1 * USB

2.0 port. The USB 3.0/3.1 ports are denoted by their blue color; the USB 2.0 port is colored black.

Note: 2 * USB 3.1 (Gen 2 Type A) ports are available as a factory option for this computer model series. The USB 3.1 ports are shared with th e USB 3.0 por ts in th is option.

HDMI Port

Note that the HDMI Port supports video and audio signals to attached external displays. Note that Sound Blaster audio will be disabled when you are connecting to an external display through an HDMI connection.



USB 3.1 Port

Speed

Note that when a single USB device is plugged in to a USB

3.1 (Gen 2) port the data transfer speed will be 10Gbps, however when two devices are plugged in to both USB 3.1 (Gen 2) ports, this bandwidth will be shared between the ports.

Quick Start Guide

System Map: Front & Left Views - Model A

1 - 18 System Map: Front & Left Views - Model A

System Map: Front & Left Views - Model B

Figure 1 - 10

Front & Left Views

Model B

1. LED Power Indicators

2. Multi-in-1 Card Reader

3. DC-In Jack

4. Vent/Fan Intake/ Outlet

5. External Monitor Port

6. RJ-45 LAN Jack

7. 2 * USB 3.0 Ports (USB 3.1 Gen 1)

2 * USB 3.1 Ports (USB 31. Gen 2 Type A) (Factory Option)

8. HDMI-Out Port



Multi-In-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RS MMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

USB 3.0 / 3.1 Port OR USB 2.0 Po rt

This model includes 3 * USB 3.0 ports (USB 3.1 Gen 1 ports) and 1 * USB

2.0 port. The USB 3.0/3.1 ports are denoted by their blue color; the USB 2.0 p ort is colored black.

Note: 2 * USB 3.1 (Gen 2 Type A) ports are available as a factory option for this computer model series. The USB 3.1 ports are shared with the USB 3 .0 port s in this option.

HDMI Port

Note that the HDMI Port supports video and audio signals to attached external displays. Note that Sound Blaster audio will be disabled when you a re connecting to an external display through an HDMI connection.



USB 3.1 Port

Speed

Note that when a single USB device is plugged in to a USB

3.1 (Gen 2) port the data transfer speed will be 10Gbps, however when two devices are plugged in to both USB 3.1 (Gen 2) ports, this bandwidth will be shared between the ports.

Quick Start Guide

System Map: Front & Left Views - Model B 1 - 19

Figure 1 - 11

Right & Rear Views

Model A

1. Microphone-In Jack

2. Headphone-Out Jack

3. 1 * USB 2.0 Port

4. 1 * USB 3.0 Port (USB 3.1 Gen 1)

5. Optical Device Drive Bay (for CD/ DVD Device)

6. Security Lock Slot

7. Battery

W255EU



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

Quick Start Guide

System Map: Right & Rear Views - Model A

1 - 20 System Map: Right & Rear Views - Model A

System Map: Right & Rear Views - Model B

Figure 1 - 12

Right & Rear Views

Model B

1. Microphone-In Jack

2. Headphone-Out Jack

3. 1 * USB 2.0 Port

4. 1 * USB 3.0 Port (USB 3.1 Gen 1)

5. Optical Device Drive Bay (for DVD Device)

6. Security Lock Slot

7. Battery

W255EU



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

Quick Start Guide

System Map: Right & Rear Views - Model B 1 - 21



Disk Eject Warning

Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.

CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”.



Changing DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click th e +

next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD Regional Codes” on page 2 - 5).

DVD region detection is device dependent, not OSdependent. You can select your module’s region code 5 times. The fifth selection is pe rmanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Quick Start Guide

1 - 22 System Map: Right & Rear Views - Model B

System Map: Bottom View - Model A

Figure 1 - 13

Bottom View

Model A

1. Battery

2. Component Bay

Cover

3. Vent/Fan Intake/

Outlet

4. Multi-in-1 Card

Reader

5. Speakers



CPU

The CPU is not a user serviceable part.



Overheating

To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.

Quick Start Guide

System Map: Bottom View - Model A 1 - 23

Figure 1 - 14

Bottom View

Model B

1. Battery

2. Component Bay

Cover

3. Vent/Fan Intake/

Outlet

4. Speakers



CPU

The CPU is not a user serviceable part.



Overheating

To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.

Quick Start Guide

System Map: Bottom View - Model B

1 - 24 System Map: Bottom View - Model B

Quick Start Guide

Desktop

Windows 10 Start Menu

Most of the apps, control panels, utilities and programs within Windows 10 can be accessed from the Start Menu by clicking the icon in the taskbar in the lower left corner of the screen (or by pressing the Windows Logo Key on the keyboard).

Figure 1 - 15 - Windows Start Menu

Windows 10 Start Menu 1 - 25

Right-Click Icon

Quick Start Guide

Right-Clicking the Windows Logo In Start Menu

Right-click the Start Menu icon (or use the Windows Logo Key + X key combination) to bring up an advanced Context Menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.

Figure 1 - 16 - Right-Click Windows Logo in Start Menu

1 - 26 Windows 10 Start Menu

Quick Start Guide

Start Menu Apps & Tiles

The Windows 10 Start Menu will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on the screen so may need click and drag the handles at the edge of the screen to expand the menu in order to view all the apps (you can use the scroll bar to mov e up and down the screen).

Figure 1 - 17 - Expanding the Start Menu

Windows 10 Start Menu 1 - 27

Quick Start Guide

Pining/Unpinning Apps & Programs to/from the Start Menu

To make things easy to find you can add and remove tiles for apps and programs to the Start Menu. Right-Click on a program’s icon and select Pin to Start from the drop-down menu. To remove an app or program from the Start Menu right-click the icon and select Unpin from Start. You can use the same method to pin apps/pro- grams to/from the taskbar (select pin to taskbar/unpin this program from the taskbar).

Figure 1 - 18 - Pin to Start/Unpin from Start

1 - 28 Windows 10 Start Menu

Windows 10 Control Panel

• Right-click the Start Menu icon

in the taskbar in the lower left corner of the screen and select Control Panel from the menu.

• Press the Windows logo key

on your keyboard and X to bring up the context menu, and then press P to bring up the Control Panel.

• Type Control Panel into the Search box in the taskbar and click on the icon when it pops up.

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 10.

Quick Start Guide

Figure 1 - 19 - Windows 10 Control Panel Access

Windows 10 Control Panel 1 - 29

Quick Start Guide

Settings

The Settings item in the Start Menu (and also as an App) gives you quick access to a number of system settings control panels allowing you to adjust settings for System, Devices, Network & internet, Personalization, Accounts, Time & language, Ease of Access, Privacy and Update & security.

Figure 1 - 20 - Settings

1 - 30 Windows 10 Control Panel

Quick Start Guide

Taskbar

Taskbar - Pinned Programs and Apps

Notification Area

Windows 10 Taskbar

In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. The notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and appli-

cations referred to throughout the course of this manual can be accessed from here.

Figure 1 - 21 - Taskbar

You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Pining/

Unpinning Apps & Programs to/from the Start Menu” on page 1 - 28).

Windows 10 Control Panel 1 - 31

Quick Start Guide

Video Features

You can switch display devices, and configure display options, from the Display control panel (in Appearance and Personalization). Click Adjust resolution to make changes to the appearance of the display and to detect

and configure any attached displays. In Windows 10 it is possible to quickly configure external displays from the Project menu (

Microsoft Hybrid Graphics

Your computer will feature Microsoft Hybrid Graphics switchable graphics technology. This seamless technology is designed to get best performance from the graphi cs system while allowing longer battery life, without having to manually change settings. The computer’s operating system (and some applications) will automati- cally switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use. This switch is seamless to the user.

press the Windows logo key on your keyboard and the P key).

The basic video features for this computer can be configured using the Intel Further video configuration is available through the NVIDA control panel (see the information on the following pages and Appendix C).

1 - 32 Video Features

® HD Graphics Control Panel.

To Configure Displays Using Project

1. Attach your display to the app ropriate port, and turn it on.

2. Press the + P key combination.

3. Click on any one of the options from the menu to select PC screen only,

Duplicate, Extend or Second screen only.

4. You can also click Connect to a wireless display at the bottom of the

Project screen and follow the steps to connect to any wireless enabled display.



NVIDIA Video Driver Controls

More detailed video controls are provided by the NVIDIA Control Panel (for more detailed information see Appendix C).

You can also access the control panel by right-clicking the desktop and selecting NVIDIA Control Panel (Figure 1 - 26 on page 1 - 37).

Quick Start Guide

Figure 1 - 22 - Project (Devices)

Video Features 1 - 33



Screen Resolution

1. Use the dropbox to select the screen Resolution (Figure 1 - 23).

2. Click Advanced settings

(Figure 1 - 23) to bring up the Advanced properties tabs.

3. Click Apply to save any changes made.

Quick Start Guide

To access Display (Control Panel) and Screen Resolution in Windows:

1. Go to the Control Panel.

2. Click Display (icon) and Adjust Resolution - In the Appearance and Personalization category.

3. Make and changes required from the Display, Resolution, Orientation or Multiple display menus.

4. Click Apply to save the settings.

Figure 1 - 23 - Screen Resolution

1 - 34 Video Features

Quick Start Guide

Display Settings:

1. You can quickly adjust the display by right-clicking the desktop and selecting Display Settings (Figure 1 -

24).

2. Adjust the settings using the sliders in the menu or click Adv anced display settings (Figure 1 - 24) to change resolution.

3. Click Apply to save any changes made to resolution.

Figure 1 - 24 - Display Settings

Video Features 1 - 35

Quick Start Guide

To access the Intel(R) HD Graphics Control Panel:

1. Click Advanced settings (Figure 1 - 23 on page 1 - 34) in the Screen Resolution control panel in Windows.

2. Click the Intel(R)... tab and click Graphics Properties (button) (below).

3. Right-click the desktop and select Graphics Properties from the menu.

4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.

Figure 1 - 25 - Intel Graphics Control Panel

1 - 36 Video Features

To access the NVIDIA Control Panel:

1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 26).

2. Double-click the icon (Figure 1 - 26) in the Windows control panel.

Quick Start Guide

Figure 1 - 26 - NVIDIA Control Panel

Video Features 1 - 37

Using the Power Button

1. Go to the Start Menu.

2. Click the Power button .

3. Select the power state required from the menu.

Quick Start Guide

Power Options

Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power button item in Start Menu (or the context menu) may be used to Shut down or Restart (you can also add Hibernate/Sleep to the menu - see page 1 - 39). To fully control all the power options (including Hibernate mode) go to the Power Options control panel and configure the power button, sleep button and lid to perform the function selected.

1 - 38 Power Options

Figure 1 - 27 - Shut Down/Restart

Quick Start Guide



Adding Hibernate/Sleep to the Power Men

1. Go to the Power Options (Hardware and Sound) control panel.

2. Click Choose what the power buttons do.

3. Click “Change settings that are currently unavailable” .

4. Click to put a check in the Hibernate/Sleep box under Shutdown settings.

5. Click Save Changes and close the control panel.

You can also use the context menu (right-click the Start Menu icon or press the Windows logo + X key combination) to Sign out, Sleep, Hibernate, Shut down, and Restart.

Figure 1 - 28 - Context Menu Shut Down or sign out

Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination to bring up a full-screen displaying Lock, Sign out, Change a password, Task Manager and Switch User. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Hibernate, Shut down, and Restart.

Power Options 1 - 39

Quick Start Guide

Minimum Screen Resolution Settings

1. Windows 10 has minimum screen resolution requirements.

2. Right-click a blank area of the Desktop and select Screen Resolution (or go to the Display control panel).

3. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above.

1 - 40 Power Options

Figure 1 - 29 - Screen Resolution

Features & Components

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components of the computer:

• Hard Disk Drive/Solid State Drive

• Optical (CD/DVD) Device

• Multi-In-1 Card Reader

• Touchpad/Clickpad and Buttons/Mouse

• Audio Features

Overview 2 - 1

Features & Components



Bottom Cover

Removal Warning

Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.

If you need to replace/ remove the hard disk/ RAM/optical device etc., for any reason, please contact your distributor/ supplier for further information.

Figure 2 - 1

Hard Disk Location



Caddy Bay Devices

This computer series supports a caddy bay for the installation of a storage device. e.g. HDD. Note that the device installed in the caddy bay is to be used for data storage only, and will not support the installation of an OS (Operating System).

Hard Disk Drive/Solid State Drive

The hard disk drive (or Solid State Drive) is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm/7mm. If you need to replace/remove the hard disk (or Solid State Drive) please contact your distributor/supplier for further information.

2 - 2 Hard Disk Drive/Solid State Drive

Features & Components



Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Win- dows. Click the Volume icon on the taskbar to check the setting (see

“Audio Features” on page 2 - 14).

Figure 2 - 2

Optical Device

123

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 2). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.

Optical (CD/DVD) Device 2 - 3

Features & Components



CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.

2 - 4 Optical (CD/DVD) Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Features & Components



DVD Region Note

DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Figure 2 - 3

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - Western Europe, Japan,

South Africa, Middle East & Egypt

• Region 3 - South-East Asia, T aiwan,

South Korea, The Philippines, Indonesia, Hong Kong

• Region 4 - South & Central Amer-

ica, Mexico, Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern

Europe, India & Most of Africa

• Region 6 - China

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.

3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control p anel to allow you to adjust the regional code.

Optical (CD/DVD) Device 2 - 5

Features & Components



Card Reader Cover

Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.

Figure 2 - 4

Front View

1. Card Reader

• MMC (MultiMedia Card) / RS MMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

Model A

Model B

Multi-In-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see

“Card Reader” on page 4 - 7.

Note: Some of these cards require PC adapters that are usually supplied with the cards.

2 - 6 Multi-In-1 Card Reader

Features & Components



Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.

Figure 2 - 5

Touchpad

Sensitivity

Touchpad/Clickpad and Buttons/Mouse

The touchpad/clickpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The touchpad/clickpad buttons function in much the same way as a two-button mouse.

Touchpad/Clickpad Sensitivity

Note that the touchpad/clickpad has a defined valid operational area of sensitivity indicated within the area of the illustration below (i.e. 4.4mm from the top and

4.9mm from the left/right sides of the Touchpad; the button area extends 17mm

from the bottom of the Touchpad).

Touchpad/Clickpad and Buttons/Mouse 2 - 7

Features & Components



Scrolling

This computer model series may feature different Touchpad versions.

These Touchpads may differ in their vertical scrolling function in most scrollable windows.

Some Touchpads require sliding the finger up and down on the right of the Touchpad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the Touchpad to scroll the window.

Figure 2 - 6

Mouse Properties

Once you have installed the Touchpad driver (see “Touchpad” on page 4 - 8) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the driver icon in the notification area of the taskbar in the Desktop app. You may then configure the tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.

2 - 8 Touchpad/Clickpad and Buttons/Mouse

Features & Components



Show Video

You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu

and click the Show Video button to see the demonstration video.

For more details on any of the gestures see the help in the lower part of the right menu window.

Figure 2 - 7

Mouse Properties -

Device Settings

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the pad to perform specific actions to manipulate documents, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Click

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (tab) and click Settings.

4. Use the menu tree on the left to access the user configurable settings.

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

Touchpad/Clickpad and Buttons/Mouse 2 - 9

Features & Components

Figure 2 - 8

Mouse Properties

(Disable Pad)

Disabling the Touchpad/Clickpad

If you need to disable the pad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the pad when resting your wrists or palms on it) you can do so by using Fn + F1 key combination.

You can also set the system to automatically disable the internal pad when an external USB point device (e.g. a USB mouse) is attached.

1. Go to the Mouse Properties control panel.

2. Click to select Device Settings (tab).

3. Click to place a check in the “Disable internal pointing device when external USB pointing device is attached” check box.

4. Click OK to save the setting.

2 - 10 Touchpad/Clickpad and Buttons/Mouse

PalmCheck™



PalmCheck™

In order to improve Clickpad/Touchpad scrolling responsiveness when using onefinger scrolling, you can adjust the PalmCheck™ slider towards “Minimum” as per your preference.

However bear in mind that adjusting the slider too far towards “Minimum” can turn off PalmCheck™ altogether.

Figure 2 - 9

PalmCheck™ Slider

The PalmCheck™ feature (Device Settings > Settings > Pointing > Sensitivity) helps prevent operating the Clickpad/Touchpad by accident, by recognizing when your palm is resting on it or brushing its surface while you are typing.

Features & Components

Touchpad/Clickpad and Buttons/Mouse 2 - 11

Features & Components

Figure 2 - 10

Scrolling Gesture



Mouse Driver

Figure 2 - 11

Zooming Gesture

Scrolling

The Two-Finger scrolling feature works in most scrollable windows an d allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the pad surface and slide both fingers in the direction required (in a straight continuous motion).

2 - 12 Touchpad/Clickpad and Buttons/Mouse

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality. Place two fingers on the pad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.

Rotating

Figure 2 - 12

Rotating Gesture

Figure 2 - 13

Flick/Press

Gesture

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the pad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The Three Fingers Down gesture may be used to launch user-selectable applications.

Features & Components

Touchpad/Clickpad and Buttons/Mouse 2 - 13

Features & Components



Volume Adjustment

The sound volume level can be clicking using the volume control icon in the notification area of the taskbar.

Figure 2 - 14

Realtek Audio

Manager

Right-click the icon to access the menu above.

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the volume icon in the taskbar or the audio slider in the Settings menu (see sidebar).

2 - 14 Audio Features

Features & Components



Disabling Front Jack

Detection

It is recommended that

you do not disable front panel jack detection in

Connector Settings . Disabling front panel jack

detection may cause your internal microphone to become disabled, and audio may continue to play through the system’s internal speakers even when headphones are plugged-in to the headphone jack.

Figure 2 - 15

Realtek Audio

Manager - Recording

Setup



Sound Blaster

Cinema 2 Audio

Note that you will need to install the Sound Blaster Cinema 2 audio application in order to get maximum audio performance. See

“Sound Blaster Cinema 2” on page 6 - 13

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:

1. Go to the

2. Click Realtek HD Audio Manager (Hardware and Sound), or right-click the taskbar icon and select Sound Manager.

3. Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust th e Recording Volume level to around 60, to obtain the optimum recording quality.

4. Click OK to close the control panel and save the settings.

Control Panel

Audio Features 2 - 15

Features & Components

2-16

Chapter 3: Power Management



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows 10 OS.)

Power Options

Power management in Windows is configured from Power Options (Hardware and Sound), which can be accessed from the Con-

trol Panel.

Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.

Overview 3 - 1



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.

Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.

3 - 2 The Power Sources

1. Attach the AC/DC adapter to the DC-in jack on the left of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “Battery FAQ” on page 3 - 21).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 17.

Turning On the Computer



Power Button as Stand by or Hibernate Button

You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring

the Power Buttons” on page 3 - 9 for details).

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.

Power Management

Turning On the Computer 3 - 3

Power Management

Figure 3 - 1

Shut Down/Restart

Shutting the Computer Down

Note that you should always shut your computer down by choosing the Shut down

command as this will help prevent hard disk or system problems. Use the Power item in the Start Menu and select Shut down.

You can also use the context menu (right-click the Start Menu Windows logo + X key combination) to Sign out, Sleep, Hibernate, Shut down, and Restart.

If you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/

Sleep to the Power Menu” on page 3 - 10.

3 - 4 Shutting the Computer Down

icon or press the

Power Plans



Resuming

Operation

See Table 3 - 1, on

page 3 - 11 for informa-

tion on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Figure 3 - 2

Power Plan

Advanced Settings

The computer can be configured to conserve power by means of power plans (Control Panel > Power Options). You can use (or modify) an existing power plan, or

create a new one. The settings may be adjusted to set the display to turn off after a specified time, and

to send the computer into Sleep after a period of inactivity. Click Change plan settings and then click Change advanced power settings to ac-

cess further configuration options in Advanced Settings.

Power Management

Power Plans3-5

Power Management

Figure 3 - 3

Power Plans

Click to Show/Hide additional power plans

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

3 - 6 Power Plans

Power-Saving States



Wake On LAN

Support

Wake-On-LAN is only supported from Sleep or

Hibernate states in Windows.

If you require your computer to wake up from network activity in Windows then make sure that the computer is either in Sleep or Hiber- nate.

Wake-On-LAN is not supported from Shutdown states in Win-

dows.

You can use power-saving states to stop the computer’s operation and restart where you left off. Windows 10 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file( s) you last used.

If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.

To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power

Menu” on page 3 - 10.

Power Management

Power-Saving States 3 - 7

Power Management

Figure 3 - 4

Power Button &

Start Menu Power

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves

all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10.

Shut down

You should Shut down the computer if you plan to install new hardware, plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.

3 - 8 Power-Saving States

Configuring the Power Buttons



Password

Protection

It is recommended that you enable a password on wake up in order to protect your data.

However you can disable this setting from the Power Options menu by clicking Require a

password on wakeup

in the left menu, and selecting the options (click

Change settings that are currently unavailable).

Figure 3 - 5

Power Options

Define Power

Buttons

The power/sleep button (Fn + F12 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.

Power Management

Configuring the Power Buttons 3 - 9

Power Management

Figure 3 - 6

Power Options

Define Power

Buttons - Shutdown

Settings

Adding Hibernate/Sleep to the Power Menu

Add Hibernate/Sleep to the Power Menu as follows.

1. Go to the Power Options (Hardware and Sound) control panel.

2. Click “Change settings that are currently unavailable” .

3. Click Choose what the power buttons do.

4. Click to put a check in the Hibernate/Sleep box under Shutdown settings.

5. Click Save Changes and close the control panel.

3 - 10 Configuring the Power Buttons

Resuming Operation

Table 3 - 1

Resuming

Operation



Closing the Lid

If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).

You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F12 key combo).

Power Status

Power Off Off Press the Power Button

Sleep Blinking Green

Hibernate

Display Turned Off Green Press a Key or Move the Mouse/Touchpad

Icon Color

Press the Sleep Button (Fn + F12 Key

Off (battery)

Orange (AC/DC adapter)

T o Resume

Press the Power Button

Combo)

Press the Power Button

Power Management

Configuring the Power Buttons 3 - 11

Power Management



Power Conservation

Modes

The Power Saving set- ting will result in maximum power saving, but with the possible loss of some performance.

Setting the mode to Bal- ance will give power saving matched with performance.

Performance will give optimum computer performance but with less power conservation.

Note that the Energy Star setting will put the display into sleep after no more than 15 minutes of user inactivity.

Figure 3 - 7

Control Center

Power Conservation Modes

This system supports Power Saving power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center:

1. Press the Fn + Esc key combination to toggle the Control Center on/off.

2. Click either the Performance, Balanced or Power Saving button.

3 - 12 Configuring the Power Buttons

Clevo W650RC1 User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Chapter 1: Quick Start Guide

Overview

Advanced Users

Beginners and Not-So-Advanced Users

Warning Boxes

Not Included

System Startup

System Software

Model Differences

System Map: LCD Panel Open - Model A

System Map: LCD Panel Open - Model B

LED Indicators

Keyboard - Model A

Keyboard - Model B

Keyboard Shortcuts

Keyboard Application Settings

Function/Hot Key Indicators

Control Center

Flexikey® Application

Flexikey® Application Features:

System Map: Front & Left Views - Model A

System Map: Front & Left Views - Model B

System Map: Right & Rear Views - Model A

System Map: Right & Rear Views - Model B

System Map: Bottom View - Model A

System Map: Bottom View - Model B

Windows 10 Start Menu

Right-Clicking the Windows Logo In Start Menu

Start Menu Apps & Tiles

Windows 10 Control Panel

Settings

Windows 10 Taskbar

Video Features

Microsoft Hybrid Graphics

Power Options

Chapter 2: Features & Components

Overview

Hard Disk Drive/Solid State Drive

Optical (CD/DVD) Device

Loading Discs

Handling CDs or DVDs

DVD Regional Codes

Multi-In-1 Card Reader

Touchpad/Clickpad and Buttons/Mouse

Gestures and Device Settings

Audio Features

Setup for Audio Recording

Chapter 3: Power Management

Overview

The Power Sources

AC/DC Adapter

Battery

Turning On the Computer

Shutting the Computer Down

Power Plans

Power-Saving States

Sleep

Hibernate

Shut down

Configuring the Power Buttons

Resuming Operation

Power Conservation Modes