Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
ErP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode:
•Off Mode < 0.5W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Re orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the service representative or an experienc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1.This device may not cause interference.
And
2.This device must accept any interference, including interfer ence that may cause undesired operation of the
device.
IV
FCC RF Radiation Exposure Statement:
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Preface
V
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1.Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2.Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3.Do not use the telephone to report a gas leak in the vicinity of the leak.
4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5.This product is intended to be supplied by a Listed Power Unit according to the model’s requirements:
•Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 2.1A (40W) minimum.
VI
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2.Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
VII
Preface
3.Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4.Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5.Take care when using peripheral devices.
Use only approved brands of
peripherals.
VIII
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
Servicing
Bottom Cover Removal Warning
Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, ple ase contact your distribu tor/
supplier for further information.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before restoring power to the system.
Also note the following when the cover is removed:
•Hazardous moving parts.
•Keep away from moving fan blades.
Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from
the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
•When the power cord or AC/DC adapter is damaged or frayed.
•If the computer has been exposed to rain or other liquids.
•If the computer does not work normally when you follow the operating instructions.
•If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•If there is an unusual odor, heat or smoke coming from your computer.
Preface
IX
Preface
Power Safety Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals and
cables (including telephone lines and power
cord).
You must also remove
your battery in order to
prevent accidentally
turning the machine on.
Before removing the
battery disconnect the
AC/DC adapter from
the computer.
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the powe r co rd, be sure to di sconn ect it b y the plug head , no t
by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
X
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.
•Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
•Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
XI
Preface
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
General Battery Precautions
•Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
•Do not remove any batteries from the computer while it is powered on.
•Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
•If you do not use the battery for an extended period, then remove the battery from the computer for storage.
•Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
•Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.
•Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
•Keep the battery away from metal appliances.
•Affix tape to the battery contacts before disposing of the battery.
•Do not touch the battery contacts with your hands or metal objects.
XII
Cleaning
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before restoring power to the system.
Also note the following when the cover is removed:
•Hazardous moving parts.
•Keep away from moving fan blades.
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply and then refer servicing to qualified service personnel under any of the following conditions:
•When the power cord or AC/DC adapter is damaged or frayed.
•If the computer has been exposed to rain or other liquids.
•If the computer does not work normally when you follow the operating instructions.
•If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•If there is an unusual odor, heat or smoke coming from your computer.
Preface
XIII
Preface
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
Travel Considerations
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.Check that the battery pack and any spares are fully charged.
2.Power off the computer and peripherals.
3.Close the display panel and make sure it’s latched.
4.Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5.The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6.Put the notebook in its carrying bag and secure it with the bag’s straps.
7.If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8.Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your “papers” are handy.
XIV
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XV
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
•Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
•Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
•Use a chair with a back and adjust it to support your lower back comfortably.
•Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
•Take periodic breaks if you are using the computer for long periods of time.
Remember to:
•Alter your posture frequently.
•Stretch and exercise your body several times a day.
•Take periodic breaks when yo u work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XVI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
•Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
•Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
•Position the display directly in front of you at a comfortable viewing distance.
•Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
•Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
•Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
•Rotate desktop background images every few days.
•Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp
edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated
logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during
transport. If any such wear and tear develops contact your distributor/supplier.
Power Safety ................................................................................................................................................X
Not Included ..............................................................................................................................................1-3
System Startup ...........................................................................................................................................1-4
System Software ........................................................................................................................................1-5
XIX
Preface
Model Differences .....................................................................................................................................1-6
System Map: LCD Panel Open - Model A ................................................................................................1-7
System Map: LCD Panel Open - Model B ................................................................................................1-8
LED Indicators ...........................................................................................................................................1-9
Control Center .........................................................................................................................................1-13
System Map: Front & Left Views ...........................................................................................................1-14
System Map: Right & Rear Views ..........................................................................................................1-15
System Map: Bottom View .....................................................................................................................1-16
Removing the Battery - Model A ............................................................................................................1-17
Inserting the Battery - Model A ...............................................................................................................1-18
Removing the Battery - Model B .............................................................................................................1-19
Inserting the Battery - Model B ...............................................................................................................1-20
Windows 10 Start Menu ..........................................................................................................................1-21
Right-Clicking the Windows Logo In Start Menu ..................................................................................1-22
Start Menu Apps & Tiles .........................................................................................................................1-23
Windows 10 Control Panel ......................................................................................................................1-25
Windows 10 Taskbar ...............................................................................................................................1-27
Video Features .........................................................................................................................................1-28
XX
Preface
Power Options .........................................................................................................................................1-33
Gestures and Device Settings ....................................................................................................................2-6
Audio Features .........................................................................................................................................2-11
Setup for Audio Recording ......................................................................................................................2-12
The Power Sources ....................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-3
Shutting the Computer Down ....................................................................................................................3-4
Power Plans ...............................................................................................................................................3-5
Power-Saving States ..................................................................................................................................3-7
Shut down ..................................................................................................................................................3-8
Configuring the Power Buttons .................................................................................................................3-9
Power Conservation Modes .....................................................................................................................3-12
Settings Menu Power Controls ................................................................................................................3-14
Battery Information .................................................................................................................................3-17
Battery Power ..........................................................................................................................................3-17
Conserving Battery Power .......................................................................................................................3-18
Battery Life ..............................................................................................................................................3-19
New Battery .............................................................................................................................................3-19
Recharging the Battery with the AC/DC Adapter ...................................................................................3-19
Proper handling of the Battery Pack ........................................................................................................3-20
What to Install ............................................................................................................................................4-1
User Account Control ................................................................................................................................4-6
Windows Security Message .......................................................................................................................4-6
New Hardware Found ................................................................................................................................4-6
Serial IO .....................................................................................................................................................4-7
Video (VGA) .............................................................................................................................................4-7
LAN ...........................................................................................................................................................4-7
Control Center ...........................................................................................................................................4-8
The Setup Utility ........................................................................................................................................5-2
Failing the POST .......................................................................................................................................5-3
Main Menu .................................................................................................................................................5-5
Advanced Menu .........................................................................................................................................5-7
Security Menu ..........................................................................................................................................5-10
Boot Menu ...............................................................................................................................................5-14
Exit Menu ................................................................................................................................................5-16
WLAN Configuration in Windows 10 ......................................................................................................6-4
Bluetooth & WLAN Combo Module ........................................................................................................6-7
Intel Bluetooth Combo Driver Installation ................................................................................................6-8
Bluetooth Configuration in Windows ........................................................................................................6-9
To Make your Computer Discoverable to Bluetooth Devices .................................................................6-11
XXIV
Preface
PC Camera Module ..................................................................................................................................6-12
Camera App .............................................................................................................................................6-13
Taking Pictures/Capturing Video ............................................................................................................6-15
Basic Hints and Tips ..................................................................................................................................7-2
Backup and General Maintenance .............................................................................................................7-3
Video Adapter ...........................................................................................................................................D-2
Communication .........................................................................................................................................D-3
Power Management ..................................................................................................................................D-3
Power ........................................................................................................................................................D-3
Features .....................................................................................................................................................D-3
Operating System ......................................................................................................................................D-3
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, Multi-in-1 card reader), TouchPad & Mouse & Audio.
• Chapter 3 The computer’s power saving options.
• Chapter 4The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 A quick guide to the computer’s PC Camera, Wireless LAN and Combo Bluetooth & WLAN modules (some of which may be optional depending on your purchase configuration).
• Chapter 7 A troubleshooting guide.
• Appendix A Definiti ons of the interface, ports/jacks which allow your computer to c ommun icat e with ex te rnal
devices.
• Appendix B Information on Control Center.
• Appendix C Information on the Videodriver controls.
• Appendix D The computer’s specification.
1
Overview 1 - 1
1
Notes
Check the light colored
boxes with the mark
above to find detailed information about the computer’s features.
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the remainder of the User’s
Manual. You may also find the notes marked with a
of interest to you.
Beginners and Non-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If
your system hasn’t been properly configured (your service representative may have already done that for you); refer to
Chapter 4 for installation instructions.
You will need to attach an optical device drive to the computer in order to access the drivers on the Device Drivers &
Utilities + User’s Manual disc. This contains the drivers and utilities necessary for the proper operation of the computer.
Ports and Jacks
See “Interface (Ports & Jacks)” on page A - 1 for a description of the interface (ports & jacks) which allow your computer
to communicate with external devices, connect to the internet etc.
Not Included
Operating Systems (e.g. Windows 10 and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
1
Overview 1 - 3
1
130°
Shutdown
Note that you should always shut your computer down by
choosing the Shut Down command in Windows (see page 1 -
29). This will help prevent hard disk or system problems.
Quick Start Guide
System Startup
1.Remove all packing materials, and place the computer on a stable surface.
2.Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3.Attach the AC/DC adapter to the DC-In jack on the right of the computer, connect the AC power cord to the AC/
DC adapter and then plug the AC power cord into an outlet (make sur e you use the adapter when first setting up
the computer).
4.Use one hand to raise the
hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).
lid/LCD to a comfortable viewing angle (
do not exceed 130 degrees
);
use the other
Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In
1 - 4 System Startup
Quick Start Guide
Windows Versions
Note that the information included on the following pages is for Windows 10 (64-bit) only.
Windows OS
In order to run Windows 10 (64-bit) without limitations or decreased performance, your computer requires a minimum
4GB of system memory (RAM).
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the Windows 10 operating system is sup-
ported.
1
System Startup 1 - 5
1
Quick Start Guide
Model Differences
This notebook series includes two different model types that mainly differ as indicated in the table below. Note that
your model may appear slightly different from those pictured in this manual (also see Appendix D for more details).
Note that the Touchpad and
Buttons has a valid operational area indicated within
the dotted lines above.
Note that only a single model is pictured here, however
the layout is the same for all
models (colors may differ).
3
5
1
7
4
6
2
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft is
usually prohibited. Make
sure the 3G/4G/WLAN/Bluetooth module(s) are
OFF if you are using the
computer aboard aircraft.
Use Fn + F11 AirplaneMode key combination to
toggle Airplane Mode On/
Off, and check the LED indicator for the power status (see Table 1 - 4, on
page 1 - 12).
1
System Map: LCD Panel Open
- Model A
System Map: LCD Panel Open - Model A 1 - 7
1
Figure 1 - 3
LCD Panel Open -
Model B
1.Built-in PC Camera
2.PC Camera LED
3.Built-In Microphone
4.LCD
5.Power Button
6.Keyboard
7.Touchpad & Buttons
7
Note that the Touchpad and
Buttons has a valid operational area indicated within
the dotted lines above.
Note that only a single model is pictured here, however
the layout is the same for all
models (colors may differ).
3
5
1
7
4
6
2
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft is
usually prohibited. Make
sure the 3G/4G/WLAN/Bluetooth module(s) are
OFF if you are using the
computer aboard aircraft.
Use Fn + F11 AirplaneMode key combination to
toggle Airplane Mode On/
Off, and check the LED indicator for the power status (see Table 1 - 4, on
page 1 - 12 ).
Quick Start Guide
1 - 8 System Map: LCD Panel Open - Model B
System Map: LCD Panel Open
- Model B
Quick Start Guide
LED Indicators
The LED indicators on the computer display helpful information about the current status of the computer.
IconColorDescription
OrangeDC Power is Plugged In
GreenThe Computer is On
Blinking GreenThe Computer is in Sleep Mode
OrangeThe Battery is Charging
GreenThe Battery is Fully Charged
Blinking OrangeThe Battery Has Reached Critically Low Power Status
OffBattery Charging has been Disabled
GreenHard Disk Activity
1
GreenAirplane Mode is ON (the WLAN, Bluetooth & 3G Modules are OFF)
Table 1 - 2 - LED Indicators
LED Indicators 1 - 9
1
Other Keyboards
If your keyboard is damaged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it automatically. However special functions/hot-keys
unique to the system’s
regular keyboard may not
work.
NumLk & Scr Lk
Hold down the Fn Key
and either Num Lk or Scr
Lk to enable number or
scroll lock, and check the
LED indicator for status.
Play/Pause
Fn Key / Windows Logo Key
Menu / Applicatio n K ey
Numerical Keypad
Function Keys
Scr LkNumLk
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.
Quick Start Guide
Keyboard
The keyboard features function keys to allow you to change operational features instantly.
1 - 10 Keyboard
Figure 1 - 4 - Keyboard
Keyboard Shortcuts
Windows Logo
Keyboard Shortcut
Use the Windows logo
key + D key com-bination to switch between the Start screen
and Windows Desktop.
Menu/Application
Keyboard Shortcut
When the Desktop app
is running you can use
the Menu/Application
key on the keyboard to display the
context menu as per a
mouse right-click.
The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in
Windows 10
.
Quick Start Guide
1
Windows Logo
Key +
Tap WinkeyToggle the Start menu
AOpen the Action Center
BSelect the Taskbar Notification Area
C Launch Cortana (in listening mode)
DToggle the Desktop
ELaunch File Explorer (Quick Access tab)
+ Number (1, 2, etc)Launch an application from the taskbar (numbered from left to right)
Description
Table 1 - 3 - Keyboard Shortcuts
Keyboard 1 - 11
1
Quick Start Guide
Function/Hot Key Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition
to the basic function key combinations; some visual indicators are available when the hot key utility is installed.
To run the Control
Center press the Fn+ Esc key combination, or double-click
the icon in the
notification area of
the taskbar.
Close the Control
Center by clicking the close icon in
the top right of the panel (move the cursor
onto the top right corner of the pa nel to
highlight it).
Control Center
When in the Windows Desktop application (not in the Start screen)press the Fn + Esc key combination, or
double-click the icon
trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/touch pad
on/off (see Appendix B for full details).
in the notification area of the taskbar to toggle the Control Center on/off. The Con-
Figure 1 - 5 - Control Center
Control Center 1 - 13
1
1
Figure 1 - 6
Front & Left Views
1.LED Indicators
2.Security Lock Slot
(
Model A Only
)
3. External Monitor
Port
4.Vent/Fan Intake/
Outlet
5.HDMI-Out Port
6.USB 3.0 Port (USB
3.1 Gen 1)
7.Microphone-In
Jack
8.Headphone-Out
Jack
1
USB 3.0 (USB 3.1 Gen 1) Port OR USB 2.0 Port
This model includes 1 * USB 3.0 (USB 3.1 Gen 1) port and 2 * USB 2.0 ports. The USB 3. 0 port is denoted by its blue
color; the USB 2.0 ports are colored black.
Optical Device Drives
To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports.
HDMI Port
Note that the HDMI Port supports video and audio signals to attached external displays.
2
7
4
1
3
6
5
8
Model A
Model B
1
Model A
Model B
3
45
768
Quick Start Guide
System Map: Front & Left Views
1 - 14 System Map: Front & Left Views
System Map: Right & Rear Views
Figure 1 - 7
Right & Rear Views
1.Security Lock Slot
(
Model B Only
)
2.DC-In Jack
3.RJ-45 LAN Jack
4.Multi-in-1 Card
Reader
5.USB 2.0 Ports
6.Battery
USB 3.0 (USB 3.1 Gen
1) Port OR USB 2.0 Port
This model includes 1 *
USB 3.0 (USB 3.1 Gen 1)
port and 2 * USB 2.0
ports. The USB 3.0 port
is denoted by its blue
color; the USB 2.0 ports
are colored black.
5
32
W255EU
4
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge
and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery
Information” on page 3 - 17 for full instructions.
Multi-In-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RS MMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
MS / MS Pro / MS Duo
6
5
Model A
Model B
1
5
32
4
5
Model A
Model B
6
Quick Start Guide
1
System Map: Right & Rear Views 1 - 15
1
Figure 1 - 8
Bottom View
1.Battery Location
2.Vent/Fan Intake/
Outlet
3.Speakers
Overheating
To prevent your computer from overheating
make sure nothing blocks
the Vent/Fan Intake while
the computer is in use.
Note that only a single
model is pictured here,
however the layout is the
same for all models (colors may differ).
1
3
Bottom Cover Removal Warning
Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may
violate the terms of your warranty.
If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please
contact your distributor/supplier for further information.
3
2
Quick Start Guide
System Map: Bottom View
1 - 16 System Map: Bottom View
Quick Start Guide
123
2
1
3
Bottom Cover Removal Warning
Do not remove any cover(s) and /or screw(s) for
the purposes of device upgrade as this may violate the terms of your warranty.
If you need to replace/remove the hard disk/RAM/
optical device etc., for any reason, please contact
your distributor/supplier for further information.
Figure 1 - 9
Battery Removal
Removing the Battery - Model A
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason
(e.g. long term storage) see below.
1.Turn the computer off, and turn it over.
2.Slide the latch in the direction of the arrow.
3.Slide the latch in the direction of the arrow, and hold it in place.
4.Slide the battery out in the direction of the arrow .
5.See over for inserting the battery instructions.
1
Removing the Battery - Model A 1 - 17
1
123
1
23
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/
optical device etc., for any
reason, please contact your
distributor/supplier for further information.
Figure 1 - 10
Battery Insertion
Quick Start Guide
Inserting the Battery - Model A
1.Slide the battery straight into the compartment (note that there are grooves on the side of the battery which
should align up with the battery compartment).
2.Lock
3.Lock the battery in place by sliding latch in the direction of the arrow
should lock automatically into place upon insertion.
.
1 - 18 Inserting the Battery - Model A
Quick Start Guide
123
4
2
1
3
Bottom Cover Removal
Warning
Do not remove any cover(s) and
/or screw(s) for the purposes of
device upgrade as this may violate the terms of your warranty.
If you need to replace/remove
the hard disk/RAM/optical device
etc., for any reason, please contact your distributor/supplier for
further information.
Figure 1 - 11
Battery Removal
4
3
Removing the Battery - Model B
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason
(e.g. long term storage) see below.
1.Turn the computer off, and turn it over.
2.Slide the latch in the direction of the arrow.
3.Slide the latch in the direction of the arrow, and hold it in place.
4.Turn the battery
5.See over for inserting the battery instructions.
in the direction of the arrow and lift it out.
1
Removing the Battery - Model B 1 - 19
1
12314
5
1
23
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/
optical device etc., for any
reason, please contact your
distributor/supplier for further information.
Figure 1 - 12
Battery Insertion
4
4
1
5
Quick Start Guide
Inserting the Battery - Model B
1.Insert the battery by aligning the battery with the pins & .
2.Turn the battery in the direction of the arrow .
3.Lock the battery in place by sliding latch in the direction of the arrow
.
1 - 20 Inserting the Battery - Model B
Quick Start Guide
Desktop
Windows 10 Start Menu
Most of the apps, control panels, utilities and programs within Windows 10 can be accessed from the Start
Menu by clicking the icon in the taskbar in the lower left corner of the screen (or by pressing the Windows
Logo Key on the keyboard).
1
Figure 1 - 13 - Windows Start Menu
Windows 10 Start Menu 1 - 21
1
Right-Click Icon
Quick Start Guide
Right-Clicking the Windows Logo In Start Menu
Right-click the Start Menu icon (or use the Windows Logo Key + X key combination) to bring up an
advanced Context Menu of useful features such as Control Panel, Programs and Features, Power Options, Task
Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
Figure 1 - 14 - Right-Click Windows Logo in Start Menu
1 - 22 Windows 10 Start Menu
Quick Start Guide
Start Menu Apps & Tiles
The Windows 10 Start Menu will contain a number of apps, and many more will be installed as you add more
applications etc. Not all of these apps can fit on the screen so may need click and drag the handles at the edge of
the screen to expand the menu in order to view all the apps (you can use the scroll bar to mov e up and down the
screen).
1
Figure 1 - 15 - Expanding the Start Menu
Windows 10 Start Menu 1 - 23
1
Quick Start Guide
Pining/Unpinning Apps & Programs to/from the Start Menu
To make things easy to find you can add and remove tiles for apps and programs to the Start Menu. Right-Click
on a program’s icon and select Pin to Start from the drop-down menu. To remove an app or program from the
Start Menu right-click the icon and select Unpin from Start. You can use the same method to pin apps/pro-grams to/from the taskbar (select pin to taskbar/unpin this program from the taskbar).
Figure 1 - 16 - Pin to Start/Unpin from Start
1 - 24 Windows 10 Start Menu
Windows 10 Control Panel
•Right-click the Start Menu icon
in the taskbar in the lower left
corner of the screen and select
Control Panel from the menu.
•Press the Windows logo key
on your keyboard and X to bring
up the context menu, and then
press P to bring up the Control
Panel.
•Type Control Panel into the
Search box in the taskbar and
click on the icon when it pops up.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel can be accessed in a number of ways in Windows 10.
Quick Start Guide
1
Figure 1 - 17 - Windows 10 Control Panel Access
Windows 10 Control Panel 1 - 25
1
Quick Start Guide
Settings
The Settings item in the Start Menu (and also as an App) gives you quick access to a number of system settings
control panels allowing you to adjust settings for System, Devices, Network & internet, Personalization, Accounts, Time & language, Ease of Access, Privacy and Update & security.
Figure 1 - 18 - Settings
1 - 26 Windows 10 Control Panel
Quick Start Guide
Taskbar
Taskbar - Pinned Programs and Apps
Notification Area
Windows 10 Taskbar
In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. The notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and appli-
cations referred to throughout the course of this manual can be accessed from here.
Figure 1 - 19 - Taskbar
You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Pining/
Unpinning Apps & Programs to/from the Start Menu” on page 1 - 24).
1
Windows 10 Control Panel 1 - 27
1
1.Attach your display to the appropriate
port, and turn it on.
2.Press the + P key combination.
3.Click on any one of the options from
the menu to select PC screen only,
Duplicate, Extend or Second
screen only.
4.You can also click Connect to a
wireless display at the bottom of the
Project screen and follow the steps
to connect to any wireless enabled
display.
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display control panel (in Appearance
and Personalization). Click Adjust resolution to make changes to the appearance of the display and to detect
and configure any attached displays. In Windows 10 it is possible to quickly configure external displays from
the Project menu (
To Configure Displays using Project
press the Windows logo key on your keyboard and theP key).
Figure 1 - 20 - Project (Devices)
1 - 28 Video Features
Quick Start Guide
2
1
Screen Resolution
1.Use the dropbox to select
the screen Resolution
(Figure 1 - 21).
2.Click Advancedsettings
(Figure 1 - 21) to bring
up the Advanced properties
tabs.
3.Click Apply to save any
changes made.
1
2
To access Display (Control Panel) and Screen Resolution in Windows:
1.Go to the Control Panel.
2.Click Display (icon) and Adjust Resolution - In the Appearance and Personalization category.
3.Make and changes required from the Display, Resolution, Orientation or Multiple display menus.
4.Click Apply to save the settings.
1
Figure 1 - 21 - Screen Resolution
Video Features 1 - 29
1
1
2
2
1
Quick Start Guide
Display Settings:
1.You can quickly adjust the display by right-clicking the desktop and selecting Display Settings (Figure 1 -
22).
2.Adjust the settings using the sliders in the menu or click Adv anced display settings (Figure 1 - 22) to
change resolution.
3.Click Apply to save any changes made to resolution.
Figure 1 - 22 - Display Settings
1 - 30 Video Features
Quick Start Guide
To access the Intel(R) HD Graphics Control Panel:
1.Right-click the desktop and select Intel(R) Graphics Settings from the menu.
OR
2.Click the icon in the notification area of the Desktop taskbar and select Intel(R) Graphics Settings from the
menu.
1
Figure 1 - 23 - Intel® HD Graphics Control Panel
Video Features 1 - 31
1
Quick Start Guide
Minimum Screen Resolution Settings
1.Windows 10 has minimum screen resolution requirements.
2.Right-click a blank area of the Desktop and select Screen Resolution (or go to the Display control panel).
3.Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above.
1 - 32 Video Features
Figure 1 - 24 - Screen Resolution
Power Options
Using the Power Button
1.Go to the Start Menu.
2.Click the Power button .
3.Select the power state required
from the menu.
Note: Systems with 32GB eMMC modules
only support Windows 10 Hybrid Boot.
Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power button item in
Start Menu (or the context menu) may be used to Shut down or Restart (you can also add Hibernate/Sleep tothe menu - see page 1 - 34). To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to perform the function selected.
Quick Start Guide
1
Figure 1 - 25 - Shut Down/Restart
Power Options 1 - 33
1
Adding Hibernate/Sleep to the Power Men
1.Go to the Power Options (Hardware and Sound)
control panel.
2.Click Choose what the power buttons do.
3.Click “Change settings that are currently unavailable” .
4.Click to put a check in the Hibernate/Sleep box
under Shutdown settings.
5.Click Save Changes and close the control panel.
Quick Start Guide
You can also use the context menu (right-click the Start Menu icon or press the Windows logo + X key
combination) to Sign out, Sleep, Hibernate, Shut down, and Restart.
Figure 1 - 26 - Context Menu Shut Down or sign out
Ctrl + Alt + Delete Key Combination
You can use the CTRL + ALT + DEL key combination to bring up a full-screen displaying Lock, Sign out,
Change a password, Task Manager and Switch User. If you click the Power icon in the lower right corner of
the screen a power management option menu appears to display Sleep, Hibernate, Shut down, and Restart.
1 - 34 Power Options
Features & Components
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive/Solid State Drive
•Multi-In-1 Card Reader
•Touchpad and Buttons/Mouse
•Audio Features
2
Overview 2 - 1
Features & Components
Bottom Cover
Removal Warning
Do not remove any cover(s) and /or screw(s) for
the purposes of device
upgrade as this may violate the terms of your
warranty.
If you need to replace/
remove the hard disk for
any reason, please contact your distributor/supplier for further
information.
2
Hard Disk Drive/Solid State Drive
The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data
in the computer. The hard disk can be taken out to accommodate other serial (SATA)
hard disk drives (see “Storage” on page D - 2 for specification information), however you will need to contact your distributor/supplier to do this in order to avoid
violating the terms of your warranty.
2 - 2 Hard Disk Drive/Solid State Drive
Features & Components
Card Reader Cover
Make sure you keep the
rubber cover provided in
the card reader when
not in use. This will help
prevent foreign objects
and/or dust getting in to
the card reader.
Figure 2 - 1
Right View
1.Card Reader
•MMC (MultiMedia Card) / RSMMC
•SD (Secure Digital) / Mini SD / SDHC / SDXC
•MS (Memory Stick) / MS Pro / MS Duo
Model A
Model B
1
1
Multi-In-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the card reader driver (see
“CardReader” on page 4 - 7).
*Note: The PC adapters are usually supplied with these cards.
2
Multi-In-1 Card Reader 2 - 3
Features & Components
Touchpad Active
Areas
Note that the pointing
active area is clearlydefined from the button active area as il-
lustrated.
Mouse Driver
If you are using an external mouse your operating system may be
able to auto-configure
your mouse during its
installation or only enable its basic functions. Be sure to check
the device’s user documentation for details.
Figure 2 - 2
Touchpad
Sensitivity
Touchpad Cleaning
In order to improve pad performance
it is necessary to keep the surface
clean and free of fingerprints and
marks etc. Use a soft dry cleaning
cloth to keep the pad surface clean.
Disabling the Pad
Use the Fn + F1 or Control Center
button to disable the Touchpad.
2
2 - 4 Touchpad and Buttons/Mouse
Touchpad and Buttons/Mouse
The Touchpad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The Touchpad buttons function in
much the same way as a two-button mouse.
Touchpad Sensitivity
The mouse button zones at the bottom of the pad are defined by the line at the bottom of the pad, and the left and right buttons are divided roughly down the middle
as illustrated below. The active area of the touchpad is that defined in the diagram
below. Press the left button zone for a left click, and right button zone for a right
click action.
Features & Components
TouchPad Scrolling
This computer model series may feature different
TouchPad versions.
These TouchPads may
differ in their vertical
scrolling function in most
scrollable windows.
Some TouchPads require
sliding the finger up and
down on the right of the
TouchPad to scroll the
window. Other versions
require tapping/holding
down the finger at the top
right or bottom right of the
TouchPad to scroll the
window.
Figure 2 - 3
Mouse Properties
Touchpad Configuration
Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 8) you
can configure the functions from the Mouse control panel in Windows, or by d oubleclicking the TouchPad driver icon in the notification area of the taskbar in the
Desktop app. You may then configure the TouchPad tapping, buttons, scrolling,
pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.
2
Touchpad Configuration 2 - 5
Features & Components
Show Video
You can get a clearer
view of the gestures involved by clicking the
Show Video option for
each gesture item.
Select the gesture (Pinch
Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Settings left tree menu
and click the Show Video
button to see the demonstration video.
For more details on any of
the gestures see the help
in the lower part of the
right menu window.
Figure 2 - 4
Mouse Properties -
Device Settings
2
Gestures and Device Settings
The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications.
You can configure the settings from the Device Settings tab in Mouse Properties:
1.Go to the
2.Click Mouse (Hardware and Sound).
3.Click Device Settings (tab) and click Settings.
4.Use the menu tree on the lef t to access the user configurable settings.
Control Panel
.
2 - 6 Touchpad Configuration
Disabling the Touchpad
Figure 2 - 5
Mouse Properties
(Disable Touchpad)
If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when
resting your wrists or palms on it) you can do so by using Fn + F1 key combination.
You can also set the system to automatically disable the internal Touchpad when an
external USB point device (e.g a USB mouse) is attached.
1.Go to the Mouse Properties control panel.
2.Click to select Device Settings (tab).
3.Click to place a check in the “Disable internal pointing device when external USB pointing device is attached” check box.
4.Click OK to save the setting.
Features & Components
2
Touchpad Configuration 2 - 7
Features & Components
PalmCheck™
In order to improve
Clickpad/Touchpad
scrolling responsiveness when using onefinger scrolling, you can
adjust the PalmCheck™
slider towards “Minimum” as per your preference.
However bear in mind
that adjusting the slider
too far towards “Minimum” can turn off PalmCheck™ altogether.
Figure 2 - 6
PalmCheck™ Slider
2
PalmCheck™
The PalmCheck™ feature (Device Settings > Settings > Pointing > Sensitivity)
helps prevent operating the Clickpad/Touchpad by accident, by recognizing when
your palm is resting on it or brushing its surface while you are typing.
2 - 8 Touchpad Configuration
Scrolling
Figure 2 - 7
Scrolling Gesture
Figure 2 - 8
Zooming Gesture
The Two-Finger scrolling feature works in most scrollable windows and allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel
in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and
slide them apart to zoom in, or closer together to zoom out.
Features & Components
2
Touchpad Configuration 2 - 9
Features & Components
Figure 2 - 9
Rotating Gesture
Figure 2 - 10
Flick/Press
Gesture
2
Rotating
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another
finger near the middle of the TouchPad and slide it in a circular motion around the
stationary finger (clockwise or counterclockwise) to rotate the object.
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of
applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.
2 - 10 Touchpad Configuration
Features & Components
Volume Adjustment
The sound volume level
can be clicking using the
volume control icon
in the notification areaof the taskbar.
Figure 2 - 11
Realtek Audio
Manager
Right-click the icon
to access the menu
above.
Audio Features
You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar
notification area/control panel (right-click the taskbar notification area icon to
bring up an audio menu). The volume may also be adjusted by means of the volumeicon in the taskbar or the audio slider in the Settings menu (see sidebar).
2
Audio Features 2 - 11
Features & Components
Disabling Front Jack
Detection
It is recommended that
you do not disable front
panel jack detection in
Connector Settings .
Disabling front panel jack
detection may cause
your internal microphone
to become disabled, and
audio may continue to
play through the system’s internal speakers
even when headphones
are plugged-in to the
headphone jack.
Figure 2 - 12
Realtek Audio
Manager - Recording
Setup
2
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instructions below:
1.Go to the
2.Click Realtek HD Audio Manager (Hardware and Sound), or right-click the
taskbar icon and select Sound Manager.
3.Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust the Recording Volume level to around 60,
to obtain the optimum recording quality.
4.Click OK to close the control panel and save the settings.
Control Panel
.
2 - 12 Audio Features
Chapter 3: Power Management
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
(Note: All pictures used
on the following pages
are from the Windows
8.1 OS.)
Power Options
Power management in
Windows is configured
from Power Options
(Hardware andSound), which can be
accessed from the Con-
trol Panel.
Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
•The Power Sources
•Turning On the Computer
•Power Plans
•Power-Saving States
•Configuring the Power Buttons
•Battery Information
•Removing the Battery - Model A
•Removing the Battery - Model B
•Intel® Dynamic Platform & Thermal Framework
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
Note: Systems with 32GB eMMC modules only support Windows 10 Hybrid Boot.
3
Overview 3 - 1
Power Management
Forced Off
If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the system to turn itself off.
3
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1.Attach the AC/DC adapter to the DC-In jack on the right of the computer, connect
the AC power cord to the AC/DC adapter and then plug the AC power cord into an
outlet (make sure you use the adapter when first setting up the computer, as
to safeguard the computer during shipping the battery will be locked to not power
the system until first connected to the AC/DC adapter).
2.Raise the lid/LCD to a comfortable viewing angle.
3.Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “Battery FAQ” on page 3 - 21).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 17.
3 - 2 The Power Sources
Turning On the Computer
Power Button as Stand by or Hibernate Button
You can use the OS’s “Power Options” control panel to set the power button to send the
system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring
the Power Buttons” on page 3 - 9 for details).
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options (Hardware and Sound) in the Windows control panel to configure
this feature.
Power Management
3
Turning On the Computer 3 - 3
Power Management
Figure 3 - 1
Shut Down/Restart
Shutting the Computer Down
Note that you should always shut your computer down by choosing the Shut down
3
command as this will help prevent hard disk or system problems. Use the Power
item in the Start Menu and select Shut down.
You can also use the context menu (right-click the Start Menu
Windows logo + X key combination) to Sign out, Sleep, Hibernate, Shutdown, and Restart.
If you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/
Sleep to the Power Menu” on page 3 - 10.
3 - 4 Shutting the Computer Down
icon or press the
Power Plans
Resuming
Operation
See Table 3 - 1, on
page 3 - 11 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 2
Power Plan
Advanced Settings
The computer can be configured to conserve power by means of power plans (Control Panel > Power Options). You can use (or modify) an existing power plan, or
create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to ac-
cess further configuration options in Advanced Settings.
Power Management
3
Power Plans3-5
Power Management
Figure 3 - 3
Power Plans
Click to Show/Hide
additional
power plans
3
Each Windowspower plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
3 - 6 Power Plans
Power-Saving States
Wake On LAN
Support
Wake-On-LAN is only
supported from Sleep or
Hibernate states in
Windows.
If you require your computer to wake up from
network activity in Windows then make sure
that the computer is either in Sleep or Hiber-nate.
Wake-On-LAN is not
supported from Shutdown states in Win-
dows.
You can use power-saving states to stop the computer’s operation and restart where
you left off. Windows 10 uses the Sleep, Hibernate and Shut Down power-saving
states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file( s) you
last used.
If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.
Power Management
3
To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power
Menu” on page 3 - 10.
Note that systems with 32GB eMMC modules only support Windows 10 Hybrid
Boot, and do not support some power saving states.
Power-Saving States 3 - 7
Power Management
Figure 3 - 4
Power Button &
Start Menu Power
Hibernate
Hibernate uses the least amount of power of all the power-saving states and saves
3
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery. To add Hibernate to the
Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10.
Shut down
You should Shut down the computer if you plan to install new hardware, plan to be
away from the computer for several days, or you do not need it to wake up and run
a scheduled task. Returning to full operation from Shut down takes longer than from
Sleep or Hibernate.
3 - 8 Power-Saving States
Configuring the Power Buttons
Password
Protection
It is recommended that
you enable a password
on wake up in order to
protect your data.
However you can disable this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that
are currently unavailable).
Figure 3 - 5
Power Options
Define Power
Buttons
The power/sleep button (Fn + F12 key combo) and closed lid may be set to send the
computer in to a power-saving state. Click Choose what the power buttons do on
the left menu in Power Options to bring up the menu.
Power Management
3
Configuring the Power Buttons 3 - 9
Power Management
Figure 3 - 6
Power Options
Define Power
Buttons - Shutdown
Settings
3
Adding Hibernate/Sleep to the Power Menu
Add Hibernate/Sleep to the Power Menu as follows.
1.Go to the Power Options (Hardware and Sound) control panel.
2.Click “Change settings that are currently unavailable” .
3.Click Choose what the power buttons do.
4.Click to put a check in the Hibernate/Sleep box under Shutdown settings.
5.Click Save Changes and close the control panel.
3 - 10 Configuring the Power Buttons
Resuming Operation
Table 3 - 1
Resuming
Operation
Closing the Lid
If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down
hot key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down).
You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F12 key combo).
Power Status
Power OffOffPress the Power Button
SleepBlinking Green
Hibernate
Display Turned OffGreenPress a Key or Move the Mouse/Touchpad
Icon Color
Press the Sleep Button (Fn + F12 Key
Off (battery)
Orange (AC/DC adapter)
T o Resume
Press the Power Button
Combo)
Press the Power Button
Power Management
3
Configuring the Power Buttons 3 - 11
Power Management
Power Conservation
Modes
The Power Saving set-
ting will result in maximum power saving, but
with the possible loss of
some performance.
Setting the mode to Bal-ance will give power
saving matched with
performance.
Performance will give
optimum computer performance but with less
power conservation.
Figure 3 - 7
Control Center
3
Power Conservation Modes
This system supports Power Saving power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period
of inactivity. Adjust Power Conservation Modes from the Control Center:
1.Press the Fn + Esc key combination to toggle the Control Center on/off.
2.Click either the Performance, Balanced or Power Saving button.
3 - 12 Configuring the Power Buttons
Ctrl + Alt + Delete Key Combination
Figure 3 - 8
Ctrl + Alt + Delete
Menu
You can use the CTRL + ALT + DEL key combination from almost any of the Windows 10 interfaces/Apps to bring up a full-screen displaying Lock, Switch User,
Sign out, Change a password and Task Manager options. If you click the Power
icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Power Management
3
To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to per-
form the function selected.
Configuring the Power Buttons 3 - 13
3
Figure 3 - 9
Settings
Power Management
Settings Menu Power Controls
The Settings item in the Start Menu (and also as an App) gives you access to a num-
ber of power settings control panels which enable you to quickly adjust power options. Click System to access the menu including the power option settings.
3 - 14 Settings Menu Power Controls
Battery Saver
Figure 3 - 10
Settings > Battery
Saver
Battery Saver will display the battery level, and by clicking Battery Use you can see
the current state of battery usage by application etc. Click Battery saver settings to
adjust the battery saver level.
Power Management
3
Settings Menu Power Controls 3 - 15
Power Management
Figure 3 - 11
Settings > Power &
Sleep
3
Power & Sleep
Power & sleep gives you quick access to Screen and Sleep settings. Click Additional power settings to go to the main power options control panel.
3 - 16 Settings Menu Power Controls
Battery Information
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 12
Battery Icon
(Notification Area) &
Battery Advanced
Settings
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Change plan settings > Change advanced power settings (see Figure
3 - 3 on page 3 - 6).
Click the battery icon in the notification area to see the current battery level and
charge status (you can also click Power & sleep settings to access the Settings
menu to quickly adjust power settings).
Power Management
3
Battery Information 3 - 17
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel
provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.
Figure 3 - 13
Windows Mobility
Center
(Control Panel)
3
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
•Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
•Reduce the amount of time before the display is turned off.
•Close wireless, Bluetooth, modem or co mmunication applications when they are
not being used.
•Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
3 - 18 Battery Information
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery”
on page 1 - 15/“Inserting the Battery” on page 1 - 16.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 21 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. Refer to “LED Indica-
tors” on page 1 - 7 for information on the battery charge status, and to “Battery
FAQ” on page 3 - 21 for more information on how to maintain and properly re-
charge the battery pack.
Power Management
3
Battery Information 3 - 19
Power Management
Caution
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your distributor/supplier. If the battery has been dropped we
do not recommend using it any further, as even if the comp uter continues to work with a
damaged battery in place, it may cause circuit damage, which may possibly result in fire. It
is recommended that you replace your computer battery every two years.
Proper handling of the Battery Pack
•DO NOT disassemble the battery pack under any circumstances
•DO NOT expose the battery to fire or high temperatures, it may explode
3
•DO NOT connect the metal terminals (+, -) to each other
3 - 20 Battery Information
Battery FAQ
Figure 3 - 14
Power Plan Create
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
1.Save and close all files and applications.
2.Create a power plan for discharging the battery and set all the options to Never.
Power Management
3
Battery Information 3 - 21
Power Management
Figure 3 - 15
Change Plan
Settings / Change
Advanced Power
Settings
3
3.Click Change plan settings (after creating it) and click Change plan settings >
Change advanced power settings.
3 - 22 Battery Information
4.Scroll down to Battery and click + to expand the ba ttery options.
Figure 3 - 16
Power Options
Advanced Settings -
Battery
5.Choose the options below (click Yes if a warning appears):
•Low battery levels = 0%
•Critical battery Levels = 1%
•Low battery action = Do Nothing
•Critical battery action (On battery) = Shut Down
•Critical battery action (Plugged in) = Do Nothing
Power Management
3
Battery Information 3 - 23
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
3 - 24 Battery Information
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.