This device complies with Part
15 of the FCC Rules. Operation
is subject to the following two
conditions:
1.This device may not cause
harmful interference.
2. This device must accept any
interference received, including interference that may
cause undesired operation.
This quick guide is a brief introduction to getting your system started. This is a s upplement, and not a substitute for the
expanded English language User’s Manual in Adobe Acrobat format on the Device Drivers & Utilities + User’s Manual
disc supplied with your computer. This disc also contains the drivers and utilities necessary for the proper oper ation of
the computer (Note: The company reserves the right to revise this publication or to change its contents without notice).
Some or all of the computer’s features may already have been setup. If they aren’t, or you are planning to re-configure
(or re-install) portions of the system, refer to the expanded User’s Manual. The Device Drivers & Utilities + User’sManual disc does not contain an operating system.
Regulatory and Safety Information
Please pay careful attention to the full regulatory notices and safety information contained in the expanded User’s Manual on the Device Drivers & Utilities + User’s Manual disc.
Intel, Intel Core, Pentium and Celeron are trademarks/registered trademarks of
Intel Corporation.
English
1
Instructions for Care and Operation
The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
• Don’t drop it, or expose it to shock. If the computer falls, the
case and the components could be damaged.
• Keep it dry, and don’t overheat it. Keep the computer and power
supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer
could be badly damaged.
English
• Avoid interference. Keep the compute r away from high capacity
transformers, electric motors, and other strong magnetic fields.
These can hinder proper performance and damage your data.
• Follow the proper working procedures for the computer. Shut
the computer down properly and don’t forget to save your work.
Remember to periodically save your data as data may be lost.
Servicing
Do not attempt to service the computer yourself. Doing so may
violate your warranty and expose you and the computer to
electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer
servicing to qualified service personnel under any of the fo llowing conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to any liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the
poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Safety Information
• Only use an AC/DC adapter approved for use with this computer.
• Use only the power cord and batteries indicated in this manual. Do
not dispose of batteries in a fire. They may explode. Check with
local codes for possible special disposal instructions.
• Do not continue to use a battery that has been dropped, or that
appears damaged (e.g. bent or twisted) in any way. Even if the
computer continues to work with a damaged battery in place, it
may cause circuit damage, which may possibly result in fire.
• Make sure that your computer is completely powered off before
putting it into a travel bag (or any such container).
• Before cleaning the computer, make sure it is disconnected from
any external power supplies, peripherals and cables (including
telephone lines). It is advisable to also remove your battery in
order to prevent accidentally turning the machine on.
• Use a soft clean cloth to clean the computer, but do not apply
cleaner directly to the computer. Do not use volatile (petroleum
distillates) or abrasive cleaners on any part of the computer.
• Do not try to repair a battery pack. Refer any battery pack repair or
replacement to your service representative or qualified service personnel.
• Note that in computer’s featuring a raised LCD electro-pl ated
logo, the logo is covered by a protective adhesive. Due to general
wear and tear, this adhesive may deter iorate over time and the
exposed logo may develop sharp edges. Be careful when handling
the computer in this case, and avoid touching the raised LCD electro-plated logo. Av oid placing any other items in the carrying bag
which may rub against the top of the computer during transport. If
any such wear and tear develops contact your service center.
2
Polymer Battery Precautions
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal
to dispose of this battery into the municipal waste stream.
Check with your local solid waste officials for details in your
area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Discard used battery a ccording to the
manufacturer’s instructions.
Note the following information which is specific to polymer
batteries only, and where applicable, this overrides the general
battery precaution information.
• Polymer batteries may experience a slight expansion or swelling,
however this is part of the battery’s safety mechanism and is not a
cause for concern.
• Use proper handling procedures when using polymer batteries. Do
not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
English
3
System Startup
.130 °
Shut Down
Note that you should always
shut your computer down by
choosing the Shut down
command in Windows (see
below). This will help prevent
hard disk or system problems.
Click Settings in the Charms
Bar (use the Windows Logo
Key + C key combina-
tion to access the Charms
Bar) and choose Shut down
from the Power menu.
Or
Choose Shut down or sign
out > Shut down from thecontext menu (use the Windows Logo Key + X key
combination to access the
context menu).
Figure 1
Opening the Lid/LCD/
Computer with AC/DC
Adapter Plugged-In
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Insert the battery and make sure it is locked in position.
4. Securely attach any peripherals you want to use with the
computer (e.g. keyboard and mouse) to their ports.
5. Attach the AC/DC adapter to the DC-In jack on the left of the
computer, then plug the AC power cord into an outlet, and
English
connect the AC power cord to the AC/DC adapter.
6. Use one hand to raise the
(do not exceed 130 degrees); use the other hand (as
angle
illustrated in Figure 1) to support the base of the computer
(Note:Never lift the computer by the lid/LCD).
7. Press the power button to turn the computer “on”.
System Software
Your computer may already come with system software
pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system,
you will find this manual refers to Microsoft Windows
8.1.
lid/LCD to a comfortable viewing
4
Model Differences
This notebook series includes three different model types that mainly differ as indicated in the table below. Note that
your model may appear slightly different from those pictured in this manual.
FeatureModel AModel BModel C
Display Type14.0” (35.56cm) HD 15.6” (39.62cm) HD17.3” (43.94cm) HD+
3G moduleFactory OptionNot Supported
340mm (w) * 238mm (d) * 26.25 -
34.7mm (h)
2.2kg
(with 48.84WH Battery and
ODD)
374mm (w) * 250mm (d) * 14.3 - 34.1mm
(h)
2.3kg
(with 48.84WH Battery and ODD)
Or
374mm (w) * 250mm (d) * 20 - 37.2mm (h)
2.6kg (with 48.84WH Battery and ODD)
413mm (w) * 270mm (d) * 14 -
40.5mm (h)
2.9kg (with 48.84WH Battery
and ODD)
Dimensions &
Weight
Or
341mm (w) * 238.5mm (d) * 16 -
34mm (h)
2.2kg
(with 48.84WH Battery and
ODD)
Or
340mm (w) * 238mm (d) * 12 -
30.2mm (h)
2.15kg (with 48.84WH Battery and
ODD)
Table 1 - Model Differences
English
5
System Map: Front View with LCD Panel Open (Model A)
4
6
3
5
7
1
Note that the Touchpad and Buttons valid operational area is
that indicated within
the red dotted lines.
8
6
3
5
7
1
8
Design I
Design II
14” (35.56cm)
2
2
8
Figure 2
Front View with LCD Panel
Open (Model A)
1. PC Camera (Optional)
2. LCD
3. Power Button
4. Hot-Key Buttons (Design I Only)
5. LED Status Indicators
6. Keyboard
7. Built-In Microphone
8. Touchpad & Buttons
14” (35.56cm)
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic transmission
devices aboard aircraft is usually prohibited.
Make sure the WLAN & Bluetooth module(s) are
OFF if you are using the computer aboard aircraft
by putting the system in to Airplane Mode.
English
6
System Map: Front View with LCD Panel Open (Models B & C)
Note that the Touchpad and
Buttons valid operational
area is that indicated within
the red dotted lines.
15.6” (39.62cm)
8
17.3” (43.94cm)
Model B
Model C
Figure 3
Front View with LCD Panel
Open (Models B & C)
1. PC Camera (Optional)
2. *PC Camera LED
*When the PC camera is
in use, the LED will be
illuminated in red.
3. LCD
4. Power Button
5. LED Status Indicators
6. Keyboard
7. *Built-In Microphone
*Note that the microphone
location is dependent
upon your model design.
8. Touchpad & Buttons
5
4
6
1
7
2
4
6
5
7
1
2
8
3
3
8
7
Wireless Device
Operation Aboard Aircraft
The use of any portable electronic transmission
devices aboard aircraft is usually prohibited.
Make sure the WLAN & Bluetooth module(s) are
OFF if you are using the computer aboard aircraft by putting the system in to Airplane Mode.
English
7
LED Indicators
Model A - Design lI
Model A - Designs l & III
Models B & C
The LED indicators on the computer display helpful information about the current status of the computer.
IconColorDescription
IconColorDescription
OrangeThe AC/DC Adapter is Plugged In
English
8
GreenThe Wireless LAN Module is Powered On
OrangeThe Bluetooth Module is Installed
GreenHard Disk Activity
Green
GreenCaps Lock Activated
GreenScroll Lock Activated
Number Lock (Numeric Keypad) Acti-
vated
Table 2 - LED Status Indicators
GreenThe Computer is On
Blinking
Green
Blinking
Orange
OrangeThe Battery is Charging
GreenThe Battery is Fully Charged
Blinking
Orange
The Computer is in Sleep Mode
The PC Camera is In Use
(14.0”/35.56cm Model A only)
The Battery Has Reached Critically
Low Power Status
Table 3 - LED Power Indicators
Hot-Key Buttons - Some Model
Models B & C
Model A
Function Keys
Num Lk &
Scr Lk
Numeric
Keypad
Fn Key
Windows Logo Key
Menu/Application Key
Function Keys
Numeric
Keypad
Fn Key
Windows Logo Key
Menu/Application Key
Num Lk &
Scr Lk
Keyboard
A Designs Only
The Hot-Key buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode/the WLAN module on/off with one
quick button press.
Hot-Key ButtonFunction
Activate the Default E-Mail Browser
Activate the Default Internet Program
or
*Toggle Silent Mode
*When enabled, Silent Mode will reduce fan noise and save power
consumption. Note this may reduce computer performance.
WLAN Module Power Toggle
or
The keyboard (Model A) has a numeric keypad for easy
numeric data input. Pressing Fn + Num Lk turns on/off
the numeric keypad. It also features function keys to allow you to change operational features instantly.
The keyboard (Models B & C) includes a numeric keypad (on the right side of the keyboard) for easy numeric
data input. Pressing Fn + Num Lk turns on/off the numeric keypad. It also features function keys to allow you
to change operational features instantly.
English
Table 4 - Hot-Key Buttons - Some Model A Designs Only
Figure 4 - Keyboard
9
Function Keys
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the
basic function key combinations, some visual indicators are available (in the Windows Desktop application only andnot in the Start Screen) when the hot key driver is installed.
Fn + F7Display ToggleFn + EscControl Center Toggle (see page 11)
Fn + F8/F9
10
Play/Pause (in Audio/Video Programs)
Turn LCD Backlight Off
(Press a key to or use Touchpad to turn on)
Volume Decrease/
Increase
Brightness Decrease/
Increase
Fn + F10
Fn + F12
Caps LockCaps Lock Toggle
PC Camera Power
Toggle
WLAN Module Power
Toggle
Bluetooth Module
Power Toggle
Table 5 - Function Keys & Visual Indicators
Control Center
When in the Windows Desktop application ( not in the Start Screen), press the Fn + Esc key combination, or doubleclick the icon in the notification area of the taskbarto toggle the Control Center on/off. The Control Center gives
quick access to frequently used controls,and enables you to quickly turn modules on/off.
Figure 5 - Control Center
English
Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off. Click on Power Conservation to switch
between Performance, Balanced or Energy Star modes. Click on the buttons (or just click and hold the mouse button)
to adjust the slider for Brightness/Volume. Click on Display Switch/Time Zone/ Desktop Background to bring up
the appropriate Windows control panel. Click on the Sleep button to put the computer into Hibernate or Sleep modes.
11
Power Status
The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter
plugged in to a working power outlet. The power status
bar will show the current battery charge state.
Brightness
The Brightness icon will show the current screen bright-
English
ness level. You can use the slider to adjust the screen
brightness or the Fn + F8/F9 key combinations, or use the
Fn + F2 key combination to turn off the LED backlight
(press any key to turn it on again). Note that screen brightness is also effected by the Power Mode selected.
Sleep
Click the Sleep button to bring up the Hibernate or
Sleep buttons, and click either button to have the
computer enter the appropriate power-saving mode.
Display Switch
Click the Display Switch button to access the menu (or
use the + P key combination) and select the appropriate display mode.
Time Zone
Clicking the Time Zone button will access the Date and
Time Windows control panel.
Volume
The Volume icon will show the current volume level. You
can use the slider to adjust the volume or the Fn + F5/F6
key combinations, or use the Fn + F3 key combination to
mute the volume.
Power Conservation
This system supports Energy Star power management
features that place computers (CPU, hard drive, etc.) into
a low-power sleep mode after a designated period of inactivity. Click either the Performance, Balanced or Ener-gy Star button.
12
Desktop Background
Clicking the Desktop Background button will allow you
to change the desktop background picture.
Touchpad/PC Camera
Click any of these buttons to toggle the Touchpad or module’s power status. A crossed out icon will appear over the
top left of the icon when it is off
status of a module, and Touchpad power, is also effected
by the Power Mode selected.
. Note that the power
System Map: Front, Left, Right, Rear & Bottom Views (Model A)
2
1
7
8
4
6
3
Left
Right
5
Front
Rear
10
13
12
Bottom
14
15
6
9
11
16
19
7
18
7
18
17
7
7
15
7
Overheating
To prevent your computer from overheating
make sure nothing blocks any vent while the
computer is in use.
Disc Emergency Eject
If you need to manually eject a disc (e.g. due
to an unexpected power interruption) you
may push the end of a straightened paper
clip into the emergency eject hole. Do not
use a sharpened pencil or similar object that
may break and become lodged in the hole.
USB 3.0 Port
The USB 3.0
ports
are col-
ored blue. USB
3.0 will transfer
data much faster
than USB 2.0,
and is backwards-compatible with USB 2.0.
6
Figure 6 - Front, Left, Right, Rear & Bottom
Views (Model A)
1. LED Power Indicators
2. DC-In Jack
3. External Monitor Port
4. RJ-45 LAN Jack
5. HDMI-Out Port
6. 2 * USB 3.0 Ports
7. Vent
8. Multi-in-1 Card
9. Microphone-In Jack
10. Headphone-Out Jack
Reader
11. USB 2.0 Port
12. Optical Device Drive
Bay
13. Emergency Eject Hole
14. Security Lock Slot
15. Battery
16. Component Bay Cover
17. Hard Disk Bay Cover
18. Speakers
19. USIM Card Cover
(Optional)
English
13
System Map: Front, Left, Right, Rear & Bottom Views (Model B)
2
1
7
8
4
6
3
Left
Right
5
Front
Rear
10
14
12
15
13
6
9
16
15
7
Bottom
17
18
7
18
19
11
Overheating
To prevent your computer from overheating
make sure nothing blocks any vent while the
computer is in use.
Disc Emergency Eject
If you need to manually eject a disc (e.g. due
to an unexpected power interruption) you
may push the end of a straightened paper
clip into the emergency eject hole. Do not
use a sharpened pencil or similar object that
may break and become lodged in the hole.
USB 3.0 Port
The USB 3.0
ports
are col-
ored blue. USB
3.0 will transfer
data much faster
than USB 2.0,
and is backwards-compatible with USB 2.0.
6
English
Figure 7 - Front, Left, Right, Rear & Bottom
Views (Model B)
1. LED Power Indicators
2. DC-In Jack
3. External Monitor Port
4. RJ-45 LAN Jack
5. HDMI-Out Port
6. 2 * USB 3.0 Ports
7. Vent
8. Multi-in-1 Card
9. Microphone-In Jack
10. Headphone-Out Jack
14
Reader
11. USB 2.0 Port
12. Optical Device Drive
Bay
13. Emergency Eject Hole
14. Security Lock Slot
15. Battery
16. Component Bay Cover
17. Hard Disk Bay Cover
18. Speakers
19. USIM Card Cover
(Optional)
System Map: Front, Left, Right, Rear & Bottom Views (Model C)
18
7
Bottom
7
2
1
7
6
4
6
3
Left
Right
5
Front
Rear
10
13
11
14
12
8
15
16
7
7
9
15
18
7
17
Overheating
To prevent your computer from overheating
make sure nothing blocks any vent while the
computer is in use.
Disc Emergency Eject
If you need to manually eject a disc (e.g. due
to an unexpected power interruption) you
may push the end of a straightened paper
clip into the emergency eject hole. Do not
use a sharpened pencil or similar object that
may break and become lodged in the hole.
USB 3.0 Port
The USB 3.0
ports
are col-
ored blue. USB
3.0 will transfer
data much faster
than USB 2.0,
and is backwards-compatible with USB 2.0.
6
Figure 8 - Front, Left, Right, Rear & Bottom
Views (Model C)
1. LED Power Indicators
2. DC-In Jack
Reader
3. External Monitor Port
4. RJ-45 LAN Jack
5. HDMI-Out Port
6. 2 * USB 3.0 Ports
7. Vent
8. Multi-in-1 Card
9. Microphone-In Jack
10. Headphone-Out Jack
11. USB 2.0 Port
12. Optical Device Drive
Bay
13. Emergency Eject Hole
14. Security Lock Slot
15. Battery
16. Component Bay Cover
17. Hard Disk Bay Cover
18. Speakers
English
15
Windows 8.1 Control Panel
Move the mouse to
the bottom left of the
screen and right-click
the Start button to access the menu.
Figure 9
Context
Menu
Figure 10
Start
Screen
Throughout this manual you will see an instruction to open the Control Panel. Right-click the Start button in the
Desktop app or Start screen (or use the Windows Logo Key + X key combination) to bring up an advanced context
menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc. and then select Control Panel.
English
Windows 8.1 Start Screen &
Desktop
The Apps, control panels, utilities and programs within
Windows are accessed from the Start screen and/or
Windows Desktop app. The Desktop (which runs as an
app within the Start screen) can be accessed by clicking
the Desktop item in the Start screen (or by using the
Windows Logo Key + D key combination). Click
the arrow at the bottom of the Start screen to access Ap-ps.
16
Apps & Tiles
Click the arrow at the bottom of the
screen to access Apps
The Start screen will contain a number of apps, and many more
will be installed as you add more applications etc. Not all of these
apps can fit on one screen so you will often need use the slider at
the bottom of the screen in order to view all the necessary Apps.
Charms Bar
The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and
Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and
then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the
Windows Logo Key + C key combination.
English
Figure 11 - Start Screen with Charms Bar
17
Video Features
1
2
2
1
Figure 12
Display
Control
Panel
Screen Resolution for Apps (Windows 8.1)
The minimum resolution in which Apps will run is
1024x768.
The minimum resolution required to support all the features of Windows 8.1 (including multitasking with snap)
is 1366x768.
The system features an Intel integrated GPU. You can
switch display devices, and configure display options,
from the Display control panel in Windows as long as the
video driver is installed.
To access the Display control panel in Windows:
1. Go to the Control Panel.
English
2. Click Display (icon) - in the Appearances and
Personalization category.
4. Right-click the desktop (use the Windows Logo Key + D
key combination to access the desktop) and select Screen resolution.
5. Use the dropbox to select the screen resolution .
6. Click Advancedsettings .
To access the Intel® HD Graphics Control Panel:
1. Click the icon (Intel® HD Graphics Control Panel) on the
Start screen.
OR
2. Right-click the desktop (use the Windows Logo Key + D
key combination to access the desktop) and select Graphics Properties from the menu.
OR
3. Click the icon in the notification area of the Desktop
taskbar and select Graphics Properties from the menu.
Display Devices
Besides the built-in LCD, you can also use an external
VGA monitor (CRT)/external Flat Panel Display or TV
(connected to the external monitor port/HDMI-Out port)
as your display device.
18
Using the Windows Logo Key + P
Figure 13
+ P (Change Display
Configuration)
Figure 14 - Power Options
Key Combination to Switch Displays
You can also use the + P key combination (or Fn + F7
) to quickly change display configuration and modes (this
is particularly useful when attaching a projector) in Win-dows.
1. Attach your external display to the external monitor port/HDMIOut port, and turn it on.
2. Press the + P (or Fn + F7) key combination.
3. An on-screen menu will pop up.
4. Use the cursor keys ( + P) to select the appropriate
configuration from the menu, and press Enter to confirm the
selection.
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows allows you to configure power
management features for your computer. You can conserve power by means of power plans and configure the
options for the power button, sleep button (Fn + F4),
computer lid (when closed), display and sleep mode (the
default power saving state) from the left menu. Note that
the Power saver plan may have an affect on computer
performance.
Click to select one of the existing plans, or click Create apower plan in the left menu and select the options to create a new plan. Click Change Plan Settings and click
Change advanced power settings to access further configuration options.
English
19
Driver Installation General
Guidelines
As a general guide follow the
default on-screen instructions for each driver (e.g.
Next > Next > Finish) unless
you are an advanced user. In
many cases a restart is required to install the driver.
Make sure any modules (e.g.
WLAN or Bluetooth) are ON
before installing the appropriate driver.
Windows Update
After installing all the drivers
make sure you enable Win-dows Update in order to get
all the latest security updates
etc. (all updates will include
the latest hotfixes from Mi-
crosoft).
Driver Installation & Power
When installing drivers make sure
your computer is powered by the
AC/DC adapter connected to a
working power source. Some drivers draw a significant amount of
power during the installation procedure, and if the remaining battery
capacity is not adequate this may
cause the system to shut down and
cause system problems (note that
there is no safety issue involved
here, and the battery will be rechargeable within 1 minute).
English
20
Driver Installation
The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities
necessary for the proper operation of the computer. This setup will probably have already been done for you. If this is not the case, insert the disc and click Install Drivers
(button), or Option Drivers (button) to access the Optional driver menu. Install the
drivers in the order indicated in Figure 15. Click to select the drivers you wish to
install (you should note down the drivers as you install them). Note: If you need to
reinstall any driver, you should uninstall the driver first
If the Found New Hardware wizard appears during the installation procedure, click
Cancel to close the window, and follow the installation procedure as directed.
Figure 15 - Install Drivers
.
3G Module
123
1
3
2
(Models A & B Only)
If you have included an optional 3G module in your purchase option, follow the instructions below to install the
USIM card (which will be provided by your service provider), and then run the appropriate application supplied
with your module.
USIM Card Insertion
1. Turn off the computer, and turn it over and remove the battery
(slide the latches in the direction indicated below and slide
the battery out).
2. Locate the SIM card cover and loosen screw and remove
the SIM card cover .
3. Insert the USIM card as you would into your mobile phone.
4. Slide the SIMLOCK towards the hinge (in the direction to the
arrow illustrated in Figure 17) in order to release the lock and
lift it up.
5. Insert the USIM card and close the SIMLOCK.
English
Figure 17 - Unlock the SIMLOCK
6. Lock the SIMLOCK by pushing it in the direction of the arrow in
Figure 18 until it clicks into the lock position.
Figure 18 - Lock the SIMLOCK
7. Replace the cover, screw and battery.
Figure 16 - Battery & SIM Card Cover Removal
21
Troubleshooting
ProblemPossible Cause - Solution
The Bluetooth module is off
after resuming from Sleep.
A file cannot be copied to/
English
from a connected Bluetooth
device.
The PC Camera module
cannot be detected.
The captured video files from
the PC Camera are taking up
too much disk space.
The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state.
Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes
from Sleep.
Transferring data between the computer and a Bluetooth enabled device is supported in one
direction only (simultaneous data transfer is not supported). If you are copying a file from your
computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth
enabled device to your computer until the file transfer process from the computer has been
completed.
The module is off. Press the Fn + F10 key combination in order to enable the module (see Table 5
on page 10). Run the camera application to view the camera picture.
Note that capturing high resolution video files requires a substantial amount of disk space for each
file.
Note that the Windows system requires a minimum of 16GB (32bit) or 20GB (64bit) of free space
on the C: drive system partition. It is recommended that you save the capture video file to a
location other than the C:drive, limit the file size of the captured video or reduce video resolution.
22
Specifications
Latest Specification Information
The specifications listed in this here
are correct at the time of going to
press. Certain items (particularly
processor types/speeds) may be
changed, delayed or updated due to
the manufacturer's release schedule. Check with your service center
for details.
One HDMI-Out Port
One Headphone-Out Jack
One Microphone-In Jack
One RJ-45 LAN Jack
One External Monitor Port
One USB 2.0 Port
Two USB 3.0 Ports
One DC-in Jack
Communication
Built-In Gigabit Ethernet LAN
(Factory Option) 300K/1.3M Pixels/2M Pix-
els (HD) PC Camera Module
(Factory Option) 3G Mini-Card Module
(Models A & B Only)
WLAN/ Bluetooth Half Mini-Card
Modules:
(Factory Option) Intel® Centrino® Wireless-N 2230 Wireless LAN (802.11b/g/n) +
Bluetooth 4.0
(Factory Option) Intel® Centrino® Wireless-N 135 Wireless LAN (802.11b/g/n) +
Bluetooth 4.0
(Factory Option) Third-Party Wireless LAN
(802.11b/g/n)
(Factory Option) Third-Party Wireless LAN
(802.11b/g/n) + Bluetooth 4.0
24
Mini Card Slots
Models A & B:
Slot 1 for WLAN Module or Combo WLAN
and Bluetooth Module
(Factory Option) Slot 2 for 3G Module
Model C:
Slot 1 for WLAN Module or Combo WLAN
and Bluetooth Modul