V12.2.00
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©April 2012
Trademarks
Intel and Atom are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.
II
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference.
And
2. This device must accept any interference, including interfer ence that may cause undesired operation of the
device.
III
Preface
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
If your purchase option includes both Wireless LAN and 3.75G modules, then the appropriate antennas will be installed.
Note that In order to comply with FCC RF exposure compliance requirements, the antenna must not be co-located or operate
in conjunction with any other antenna or transmitter.
Important Notice - 3.75G/HSPA & Bluetooth/Wireless LAN Modules
In order to comply with FCC regulations you should NOT operate the 3.75G/HSPA module and the Bluetooth/Wireless LAN
modules at the same time as this may disrupt radio frequency, and cause interference. When the 3.75G/HSPA module is
powered on, make sure that the Bluetooth/Wireless LAN modules are powered off.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
IV
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be su pplied by a Listed Power Unit (Full Range 30W AC/DC Adapter – AC Input 100
- 240V, 50 - 60Hz, DC Output 19V, 1.58A).
EuP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode:
• Off Mode < 1W
V
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
VI
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut th e comp uter down pro per ly and don’t for ge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
VII
Preface
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines and
power cord).
You must also remove
your battery in order to
prevent accidentally
turning the machine
on. Before removing
the battery disconnect the AC/DC
adapter from the
computer.
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local p ower specifications,
VIII
consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
• Make sure the socket and any extens ion cord(s) you use c an support the total curre nt load
of all the connected devices.
• Before cleaning the computer , make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.
• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
IX
Preface
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteri es
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
X
Cleaning
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Preface
XI
Preface
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prev ent your
computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both
hardware and software. Make sure your documents are prepared.
XII
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XIII
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or
on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XIV
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long ).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp
edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated
logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during
transport. If any such wear and tear develops contact your service center.
XV
Preface
XVI
Preface
Contents
Notice .............................................................................................................................................................I
FCC Statement ............................................................................................................................................III
FCC RF Radiation Exposure Statement: ....................................................................................................IV
EuP Off Mode Power Consumption Statement: ..........................................................................................V
Instructions for Care and Operation ...........................................................................................................VI
Power Safety ............................................................................................................................................VIII
Polymer Battery Precautions ......................................................................................................................IX
Battery Precautions ......................................................................................................................................X
Cleaning ......................................................................................................................................................XI
Servicing .....................................................................................................................................................XI
Travel Considerations ............................................................................................................................... XII
Quick Start Guide
Overview ....................................................................................................................................................1-1
Advanced Users .........................................................................................................................................1-2
Beginners and Not-So-Advanced Users ....................................................................................................1-2
Warning Boxes ..........................................................................................................................................1-2
Not Included ..............................................................................................................................................1-3
System Software ........................................................................................................................................1-4
Model Differences .....................................................................................................................................1-5
System Startup ...........................................................................................................................................1-6
XVII
Preface
System Map: LCD Panel Open - Models A & B .......................................................................................1-7
System Map: LCD Panel Open - Model C ................................................................................................1-8
System Map: LCD Panel Open - Model D ................................................................................................1-9
Keyboard ..................................................................................................................................................1-10
Function/Hot Key Indicators ...................................................................................................................1-11
System Map: Front & Rear Views ...........................................................................................................1-12
LED Indicators .........................................................................................................................................1-13
System Map: Left View ...........................................................................................................................1-14
System Map: Right View .........................................................................................................................1-15
System Map: Bottom View .....................................................................................................................1-16
3.75G/HSPA Module USIM Card Installation ........................................................................................1-17
Windows 7 Start Menu & Control Panel .................................................................................................1-18
Video Features .........................................................................................................................................1-19
Power Options .........................................................................................................................................1-21
Features & Components
Overview ....................................................................................................................................................2-1
Hard Disk Drive .........................................................................................................................................2-2
External USB Optical (CD/DVD) Device .................................................................................................2-3
Loading Discs ............................................................................................................................................2-3
Handling CDs or DVDs .............................................................................................................................2-4
DVD Regional Codes ................................................................................................................................2-5
XVIII
Preface
Multi-In-1 Card Reader .............................................................................................................................2-6
Touchpad and Buttons/Mouse ...................................................................................................................2-7
Finger Sensing Pad Configurator ...............................................................................................................2-8
Gestures .....................................................................................................................................................2-9
Audio Features .........................................................................................................................................2-10
Adding a Printer .......................................................................................................................................2-12
USB Printer ..............................................................................................................................................2-12
Parallel Printer .........................................................................................................................................2-12
Power Management
Overview ....................................................................................................................................................3-1
The Power Sources ....................................................................................................................................3-2
AC/DC Adapter .........................................................................................................................................3-2
Battery ........................................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-3
Power Plans ...............................................................................................................................................3-4
Power-Saving States ..................................................................................................................................3-6
Sleep ..........................................................................................................................................................3-6
Hibernate ....................................................................................................................................................3-7
Shut down ..................................................................................................................................................3-7
Configuring the Power Buttons .................................................................................................................3-8
Resuming Operation ..................................................................................................................................3-9
XIX
Preface
Energy Star Power Saving .......................................................................................................................3-10
Battery Information .................................................................................................................................3-11
Battery Power ..........................................................................................................................................3-11
Conserving Battery Power .......................................................................................................................3-12
Battery Life ..............................................................................................................................................3-13
New Battery .............................................................................................................................................3-13
Recharging the Battery with the AC/DC Adapter ...................................................................................3-13
Proper handling of the Battery Pack ........................................................................................................3-14
Battery FAQ .............................................................................................................................................3-15
Drivers & Utilities
What to Install ............................................................................................................................................4-1
Driver Installation ......................................................................................................................................4-2
Updating/Reinstalling Individual Drivers ..................................................................................................4-4
User Account Control ................................................................................................................................4-4
Windows Security Message .......................................................................................................................4-4
New Hardware Found ................................................................................................................................4-5
Driver Installation Procedure .....................................................................................................................4-5
Chipset .......................................................................................................................................................4-5
Video (VGA) .............................................................................................................................................4-5
LAN ...........................................................................................................................................................4-5
Card Reader ...............................................................................................................................................4-6
XX
Preface
TouchPad ...................................................................................................................................................4-6
Hot Key ......................................................................................................................................................4-6
Audio .........................................................................................................................................................4-6
Windows Experience Index .......................................................................................................................4-7
Optional Drivers ........................................................................................................................................4-8
PC Camera Module ....................................................................................................................................4-9
Wireless LAN Module ...............................................................................................................................4-9
3.75G/HSPA Module .................................................................................................................................4-9
Bluetooth Module ......................................................................................................................................4-9
Trusted Platform Module ...........................................................................................................................4-9
BIOS Utilities
Overview ....................................................................................................................................................5-1
The Power-On Self Test (POST) ...............................................................................................................5-2
Failing the POST .......................................................................................................................................5-3
Fatal Errors ................................................................................................................................................5-3
Non-Fatal Errors ........................................................................................................................................5-3
The Setup Utility ........................................................................................................................................5-4
Entering Setup ...........................................................................................................................................5-4
Setup Screens .............................................................................................................................................5-5
Main Menu .................................................................................................................................................5-6
System Time & Date (Main Menu) ...........................................................................................................5-6
XXI
Preface
System / Total Memory (Main Menu) .......................................................................................................5-7
MB Series / BIOS Version / KBC/EC Firmware Revision (Main Menu) .................................................5-7
Advanced Menu .........................................................................................................................................5-8
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-8
SATA Controller Mode (Advanced Menu) ...............................................................................................5-8
Diagnostic Splash Screen (Advanced Menu) ............................................................................................5-9
Power On Boot Beep (Advanced Menu) ...................................................................................................5-9
Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9
Security Menu ..........................................................................................................................................5-10
Set Supervisor Password (Security Menu) ..............................................................................................5-10
Set User Password (Security Menu) ........................................................................................................5-11
Password on boot (Security Menu) ..........................................................................................................5-11
TPM (Trusted Platform Module) Support: (Security Menu) ...................................................................5-11
TPM State ................................................................................................................................................5-12
Change TPM State (TPM State) ..............................................................................................................5-12
Boot Menu ...............................................................................................................................................5-14
Exit Menu ................................................................................................................................................5-15
Upgrading The Computer
Overview ....................................................................................................................................................6-1
When Not to Upgrade ................................................................................................................................6-2
Removing the Battery ................................................................................................................................6-3
XXII
Preface
Upgrading the System Memory (RAM) ....................................................................................................6-4
Upgrading the Hard Disk ...........................................................................................................................6-7
Modules & Options
Overview ....................................................................................................................................................7-1
PC Camera Module ....................................................................................................................................7-2
PC Camera Driver Installation ...................................................................................................................7-3
Wireless LAN Module .............................................................................................................................7-10
802.11b/g/n Driver Installation (for WLAN Module) .............................................................................7-11
3rd Party 802.11b/g/n Driver Installation (for Combo Modules) ............................................................7-12
Intel® Wi-Fi Link Series Driver Installation ...........................................................................................7-13
Connecting to a Wireless Network in Windows 7 ...................................................................................7-14
Intel® My WiFi Configuration ................................................................................................................7-17
Intel WLAN & Bluetooth Combo Module High-Speed Data Transfer Configuration ...........................7-29
Windows Mobility Center .......................................................................................................................7-31
3.75G/HSPA Module ...............................................................................................................................7-32
Wireless Manager ....................................................................................................................................7-34
Wireless Manager Installation .................................................................................................................7-34
Wireless Manager Application ................................................................................................................7-35
Profiles .....................................................................................................................................................7-38
Settings ....................................................................................................................................................7-42
Text Messaging Service (SMS) ...............................................................................................................7-45
XXIII
Preface
SMS Utility ..............................................................................................................................................7-45
Sending a Text Message ..........................................................................................................................7-47
Phonebook ...............................................................................................................................................7-50
SMS Settings ...........................................................................................................................................7-53
Bluetooth Module ....................................................................................................................................7-56
3rd Party Bluetooth Combo Driver Installation Information ..................................................................7-57
3rd Party Bluetooth Combo Driver Installation .......................................................................................7-58
3rd Party Bluetooth (V3.0) & WLAN Combo Settings .........................................................................7-59
Bluetooth Networking Setup ...................................................................................................................7-62
Bluetooth & WLAN Combo Module Configuration ...............................................................................7-63
Intel Bluetooth Combo Driver Installation ..............................................................................................7-66
Standard Bluetooth Configuration in Windows 7 ...................................................................................7-67
Trusted Platform Module .........................................................................................................................7-71
Initializing TPM .......................................................................................................................................7-72
Trusted Platform Module (TPM) Driver Installation ..............................................................................7-75
Initializing TPM .......................................................................................................................................7-76
Infineon Security Platform Settings Tool ................................................................................................7-78
Troubleshooting
Overview ....................................................................................................................................................8-1
Basic Hints and Tips ..................................................................................................................................8-2
Backup and General Maintenance .............................................................................................................8-3
XXIV
Preface
Viruses .......................................................................................................................................................8-4
Upgrading and Adding New Hardware/Software ......................................................................................8-5
Problems and Possible Solutions ...............................................................................................................8-7
Bluetooth Connection Problems ..............................................................................................................8-12
Intel® Centrino WLAN & Bluetooth Combo Module ............................................................................8-16
Interface (Ports & Jacks)
Notebook Ports and Jacks .........................................................................................................................A-2
Intel Video Driver Controls
Intel Video Driver Installation ..................................................................................................................B-1
Video (VGA) ............................................................................................................................................B-1
Shared Video Memory ..............................................................................................................................B-1
Intel® Graphics & Media Control Panel ..................................................................................................B-2
Display Devices & Options ......................................................................................................................B-4
Attaching Other Displays .........................................................................................................................B-5
Configuring an External Display in Windows 7 .......................................................................................B-7
HDMI Audio Configuration ...................................................................................................................B-10
Specifications
Processor ...................................................................................................................................................C-2
Core Logic ................................................................................................................................................C-2
Display ......................................................................................................................................................C-2
XXV
Preface
Memory .....................................................................................................................................................C-2
Video Adapter for N2800 Processor .........................................................................................................C-2
Video Adapter for N2600 Processor .........................................................................................................C-2
BIOS .........................................................................................................................................................C-2
Storage ......................................................................................................................................................C-2
Security .....................................................................................................................................................C-2
Audio ........................................................................................................................................................C-3
Pointing Device ........................................................................................................................................C-3
Keyboard ...................................................................................................................................................C-3
Interface ....................................................................................................................................................C-3
Card Reader ..............................................................................................................................................C-3
Slot ............................................................................................................................................................C-3
Communication .........................................................................................................................................C-3
Communication .........................................................................................................................................C-3
Operating Systems ....................................................................................................................................C-4
Power Management ..................................................................................................................................C-4
Power ........................................................................................................................................................C-4
Battery .......................................................................................................................................................C-4
Design Feature ..........................................................................................................................................C-4
Environmental Spec ..................................................................................................................................C-4
Dimensions & Weight ..............................................................................................................................C-4
XXVI
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, card reader), TouchPad & Mouse, Audio & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, 3.75G/HSPA, Combination Blue-
tooth & WLAN and Trusted Platform (TPM) modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the Intel Video driver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
1
Notes
Check the light colored
boxes with the mark
above to find detailed information about the computer’s features.
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properl y installed. If
your system hasn’t been properly configured (your service representative may have already done that for you); refer to
Chapter 4 for installation instructions.
You will need to attach an optical device drive to the computer in order to access the drivers on the Device Drivers &
Utilities + User’s Manual disc. This contains the drivers and utilities necessary for the proper operation of the computer.
Ports and Jacks
See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Not Included
Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs)
have their own manuals, so please consult the appropriate manuals.
1
Overview 1 - 3
1
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7
(32-bit version only) operating system with Service Pack 1 installed.
Operating System & Version Note
Windows 7(32-bit Version Only)
1 - 4 Overview
In order to run Windows 7 without limitations or decreased performance,
your computer requires a minimum 1GB of system memory (RAM).
Table 1 - 1 - Operating Systems Supported
Quick Start Guide
Model Differences
This notebook series includes some model types that differ slightly in design style, and in particular the LCD
back cover options (see Appendix C for full specification details). Note that your model’s appearance may appear slightly different from those pictured throughout this manual.
Feature Model A Model B Model C Model D
1
Panel
Thickness
Dimensions
Weight
5.2mm Thick Panel 3.6 mm Thick Panel 5.2mm Thick Panel
266mm (w) * 185mm (d) *
19.7 - 27.1mm (h)
0.95kg with 3 Cell Battery 0.93kg with 3 Cell Battery 0.96kg with 3 Cell Battery 0.93kg with 3 Cell Battery
266mm (w) * 185mm (d) *
18.5 - 26.6mm (h)
266mm (w) * 185mm (d) *
19.7 - 27.1mm (h)
265mm (w) * 187mm (d) *
16.7 - 26.9mm (h)
See “Specifications” on page D - 1 for full details .
Table 1 - 2 - Model Differences
Overview 1 - 5
1
Shutdown
Note that you should always
shut your computer down by
choosing the Turn Off Com-
puter command from the
Start menu in Windows. This
will help prevent hard disk or
system problems.
Quick Start Guide
System Startup
1. Remove all packing materials, and place the computer on a stable surface.
2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
4.
Use one hand to raise the
hand (as illustrated in
the lid/LCD).
5. Press the power button on the side of the computer fo r about 2 - 3 second s to turn the computer “ on” (note th at
the power LED on the front of the computer will turn from orange to green when the computer powers on).
Figure 1 - 1 - Opening the Lid/LCD/Computer with AC/DC Adapter Plugged-In
lid/LCD to a comfortable viewing angle (do not exceed 120 degrees);
Figure 1 - 1
below) to support the base of the computer (Note: Never lift the computer by
use the other
1 - 6 System Startup
System Map: LCD Panel Open - Models A & B
Figure 1 - 2
LCD Panel Open -
Models A & B
1. Built-In PC Camera
2. LCD
3. Keyboard
4. Built-In Microphone
5. Touchpad &
Buttons
2
1
5
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using
the computer aboard aircraft.
Use the key combinations to
toggle power to the WLAN/
Bluetooth or 3.75G modules,
and check the LED indicator
icon to see if the modules are
powered on or not (see
Table 1 - 3, on page 1 - 11/
Table 1 - 4, on page 1 - 13).
4
Quick Start Guide
1
System Map: LCD Panel Open - Models A & B 1 - 7
1
Figure 1 - 3
LCD Panel Open -
Model C
1. Built-In PC Camera
2. LCD
3. Power Button
4. Keyboard
5. Built-In Microphone
6. Touchpad &
Buttons
2
1
6
4
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using
the computer aboard aircraft.
Use the key combinations to
toggle power to the WLAN/
Bluetooth or 3.75G modules,
and check the LED indicator
icon to see if the modules are
powered on or not (see
Table 1 - 3, on page 1 - 11/
Table 1 - 4, on page 1 - 13).
5
3
Quick Start Guide
System Map: LCD Panel Open - Model C
1 - 8 System Map: LCD Panel Open - Model C
System Map: LCD Panel Open - Model D
Figure 1 - 4
LCD Panel Open -
Model D
1. Built-In PC Camera
2. Built-In Microphone
3. LCD
4. Keyboard
5. Touchpad &
Buttons
2
1
4
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using
the computer aboard aircraft.
Use the key combinations to
toggle power to the WLAN/
Bluetooth or 3.75G modules,
and check the LED indicator
icon to see if the modules are
powered on or not (see
Table 1 - 3, on page 1 - 11/
Table 1 - 4, on page 1 - 13).
5
3
Quick Start Guide
1
System Map: LCD Panel Open - Model D 1 - 9
1
Other Keyboards
If your keyboard is damaged or
you just want to make a change,
you can use any standard USB
keyboard. The system will detect and enable it automatically.
However special functions/hotkeys unique to the system’s regular keyboard may not work.
Play/Pause Key
Function Keys
NumLk &
ScrLk Keys
Toggle Key
3.75G/HSPA
Module Power
Fn Key
Numerical Keypad
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row o f the keyboard) will
not work. Make sure that NumLk is on.
Quick Start Guide
Keyboard
The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change
operational features instantly. See Table 1 - 3, on page 1 - 11 for details on the function keys.
Figure 1 - 5 - Keyboard
1 - 10 Keyboard
Quick Start Guide
Function/Hot Key Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.
Keys Function Keys Function
Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle
1
Fn +
Fn + F1 TouchPad Toggle Fn + F10 PC Camera Power Toggle
Fn + F2
Fn + F3 Mute Toggle Fn + F12
Fn + F4 Sleep Toggle Fn + NumLk Number Lock Toggle
Fn + F5/F6
Make sure the Hot Key driver is installed - see “Hot Key” on page 4 - 6. Caps Lock Caps Lock Toggle
3.75G Module Power
Toggle
(Press a key to or use TouchPad to turn on)
Volume Decrease/
Increase
Turn LCD Backlight Off
Fn + F8/F9
Fn + F11 WLAN Module Power T oggle
Fn + ScrLk Scroll Lock Toggle
Brightness Decrease/
Increase
Bluetooth Module Power
Toggle
Table 1 - 3 - Function & Hot Key Indicators
Function/Hot Key Indicators 1 - 11
1
Figure 1 - 6
Front & Rear Views
1. LED Indicators
2. Battery
1
2
2
Models A, B & C
Model D
Quick Start Guide
System Map: Front & Rear Views
1 - 12 System Map: Front & Rear Views
LED Indicators
Icon Color Description
Quick Start Guide
Orange DC Power is Plugged In
Green The Computer is On
Blinking Green The Computer is in Sleep Mode
Orange The Battery is Charging
Green The Battery is Fully Charged
Blinking Orange The Battery Has Reached Critically Low Power Status
Green Hard Disk Activity
Green The (optional) Wireless LAN Module is Powered On
Orange The (optional) Bluetooth Module is Powered On
Table 1 - 4 - LED Indicators
1
System Map: Front & Rear Views 1 - 13
1
Figure 1 - 7
Left View
1. Security Lock Slot
2. DC-In Jack
3. Vent/Fan Intake/
Outlet
4. HDMI-Out Port
5. USB 2.0 Port
6. Microphone-In Jack
7. Headphone-Out
Jack
1
3
6
5
7
External Optical (CD/DVD) Device Drives
To install applications and drivers etc. you will
need to attach an external optical CD/DVD device
to the USB ports.
Overheating
To prevent your computer from
overheating make sure nothing
blocks the vent(s)/fan intake(s)
while the computer is in use.
2
4
1
3
6
5
7
2
4
Models A, B & C
Model D
Quick Start Guide
System Map: Left View
1 - 14 System Map: Left View
System Map: Right View
Figure 1 - 8
Right View
1. Multi-In-1 Card
Reader
2. 2 * USB 2.0 Ports
3. RJ-45 LAN Jack
4. External Monitor
Port
5. Power Button
(Models A, B & D
Only)
Overheating
To prevent your computer from overheating
make sure nothing
blocks the vent(s)/fan intake(s) while the computer is in use.
1
2 3
5
4
Multi-In-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RS MMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
MS (Memory Stick) / MS Pro / MS Duo
Note: Some of these cards require PC adapters that are usually supplied with the cards.
2
1
2 3 42
Models A & B
Model C
1
2 2
3
4
5
Model D
Quick Start Guide
1
System Map: Right View 1 - 15
1
Figure 1 - 9
Bottom View
1. Battery
2. Component Bay
Cover
3. Vent/Fan Intake/
Outlet
4. Speakers
CPU
The CPU is not a user
serviceable part. Opening this compartment, or
accessing the CPU in
any way, may violate
your warranty.
1
3
2
4
3.75G/HSPA Module USIM Card
The 3.75G/HSPA module’s USIM card location is located under the battery compartment. See page 1
- 17 for instructions on installing the 3.75G/HSPA USIM card.
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge
and charge the battery at least once every 30 days or after about 20 partial discharges.
4
1
2
3
4 4
Models A, B & C
Model D
Quick Start Guide
System Map: Bottom View
1 - 16 System Map: Bottom View
Quick Start Guide
USIM Card
Orientation
Note that the USIM
card’s readable side
(with the gold-colored
contacts) should face
upwards as illustrated.
3.75G/HSPA Module USIM Card Installation
If you have included an optional 3.75G/HSPA module in your purchase option, follow the instructions below to
install the USIM card (which will be provided by your service provider), and then run the appropriate application. See “Wireless Manager” on page 7 - 34 for instructions on installing the program etc.
1. Turn off the computer, and turn it over and then remove the battery (slide the latches in the direction indicated
below and slide the battery out).
2. Insert the USIM card into the slot at the back of the battery compartment as illustrated below until it clicks fully
into position, and replace the battery.
Figure 1 - 10 - Battery Removal & USIM Card Insertion
1
3.75G/HSPA Module USIM Card Installation 1 - 17
1
Figure 1 - 11 - Start Menu & Control Panel
Click here to toggle Category View
Quick Start Guide
Windows 7 Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows 7 are accessed from the Start menu. When
you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be
placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if
you want to customize the appearance of the Start menu.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features,
however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all
controls it may be necessary to toggle off Category View to view the control panel icons.
1 - 18 Windows 7 Start Menu & Control Panel
Quick Start Guide
1
2
1
2
Video Features
You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows 7. For more detailed video information see “Intel Video Driver Controls” on
page B - 1. To access Display (Control Panel) and Screen Resolution in Windows:
1. Click Start and click Control Panel.
2. Click Display (icon) - In the Appearances and Personalization category.
3. Click Adjust Screen Resolution/Adjus t resolution.
4. Alternatively you can right-click the desktop and select Screen resolution.
5. Use the drop box to select the screen Resolution (Figure 1 - 12).
6. Click Advanced settings (Figure 1 - 12) to bring up the Advanced properties tabs.
1
Figure 1 - 12 - Screen Resolution
Video Features 1 - 19
1
234
3
4
Quick Start Guide
To access the Intel(R) Graphics and Media Control Panel:
1. Click Advanced settings (Figure 1 - 12 on page 1 - 19) in the Display Settings control panel in Windows.
2. Click Graphics Properties (button) (Figure 1 - 13) in the Intel Graphics Media Accelerator Driver tab.
OR
3. Right-click the desktop and select Graphics Properties from the menu.
OR
4. Click the icon (Figure 1 - 13) in the notification area and select Graphics Properties from the menu.
OR
5. Access the Intel(R) Graphics and Media Control Panel from the Windows control panel in Classic V iew.
6. Choose the application mode (Basic, Advanced or Wizard) required.
Figure 1 - 13 - Intel Graphics and Media Control Panel
1 - 20 Video Features
Quick Start Guide
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 18 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change plan settings and click Change advanced power settings to access further configuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 11.
1
Figure 1 - 14 - Power Options
Power Options 1 - 21
1
Quick Start Guide
1 - 22
Features & Components
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive
• External USB Optical (CD/DVD) Device
• Multi-In-1 Card Reader
• Touchpad and Buttons/Mouse
• Audio Features
• Adding a Printer
2
Overview 2 - 1
Features & Components
Power Safety
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Hard Disk Drive Speeds
If you are going to upgrade/replace the hard disk drive , note that It is recommended that
HDDs of a maximum speed of 5400 RPM are used. 7200rpm or higher HDDs are not
approved.
2
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" serial (SATA) HDDs with a height of 9.5 mm.
If you want to upgrade your computer by replacing the existing hard disk with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may
damage the computer and may violate your warranty.
2 - 2 Hard Disk Drive
Features & Components
USB Cables
You can connect the optional USB optical device using one of the
USB cables. However if
you are experiencing
connection or power
problems, connect both
USB cables from the device to the computer.
External Optical
(CD/DVD) Device
Drives
To install applications
and drivers etc. you will
need to attach an external optical CD/DVD device to the USB ports.
External USB Optical (CD/DVD) Device
An external USB optical (CD/DVD) device is available as an option for this computer. The optical device may be used as a boot device if properly set in the BIOS
(see “Boot Menu” on page 5 - 14).
Loading Discs
To insert a CD/DVD, simply slide the disc into the disc slot with label-side facing
up. The busy indicator will light up while data is being accessed, or while a disc is
playing. If power is unexpectedly interrupted, insert an object such as a straightened
paper clip into the emergency eject hole to eject the disc.
2
External USB Optical (CD/DVD) Device 2 - 3
Features & Components
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
2
Handling CDs or DVDs
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
2 - 4 External USB Optical (CD/DVD) Device
Features & Components
Table 2 - 1
DVD Regional Coding
DVD Regional Codes
Go to the Control Panel and double-click Device Manager (Hardware and
Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-
ROM device to bring up the Properties dialog box, and select the DVD Region
(tab) to bring up the control panel to allow you to adjust the regional code.
DVD region detection is device dependent, not OS-dependent. You can select your
module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another
computer.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2 Western Europe, Japan, South Africa, Middle East & Egyp t
3
4 South & Central America, Mexico, Australia, New Zealand
5 N Korea, Russia, Eastern Europe, India & Most of Africa
6 China
South-East Asia, Taiwan, South Korea, The Philippines,
Indonesia, Hong Kong
2
External USB Optical (CD/DVD) Device 2 - 5
Features & Components
Card Reader Cover
Make sure you keep the
rubber cover provided in
the card reader when
not in use. This will help
prevent foreign objects
and/or dust getting in to
the card reader.
Figure 2 - 1
Right View
1. Card Reader
• MMC (MultiMedia Card) / RS MMC
• SD (Secure Digital) / Mini SD / SDHC / SDXC
• MS (Memory Stick) / MS Pro / MS Duo
1
Models A & B
Model C
1
Model D
1
2
Multi-In-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the card reader driver (see
“Card Reader” on page 4 - 6).
Note: Some of these cards require PC adapters that are usually supplied with the
cards.
2 - 6 Multi-In-1 Card Reader
Features & Components
Touchpad Scrolling
This computer model series may feature different
Touchpad versions.
These Touchpads may
differ in their vertical
scrolling function in most
scrollable windows.
Some Touchpads require
sliding the finger up and
down on the right of the
Touchpad to scroll the
window. Other versions
require tapping/holding
down the finger at the top
right or bottom right of the
Touchpad to scroll the
window.
Figure 2 - 2
Mouse Properties
Touchpad and Buttons/Mouse
The Touchpad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The Touchpad buttons function in
much the same way as a two-button mouse.
Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you
can configure the functions by double-clicking the TouchPad driver icon in the
taskbar. You may then configure the buttons, pointers and finger-sensing pad options to your preferences.
2
Touchpad and Buttons/Mouse 2 - 7
Features & Components
Figure 2 - 3
Finger Sensing
Pad
2
Finger Sensing Pad Configurator
The Finger Sensing Pad Configurator allows you to use a configure the settings
for the Finger Pad device and software. The left pane in the control panel contains
all the configurable items, and you can click the “+” to expand the menu selections.
You can configure the settings from the Device Settings tab in Mouse Properties:
1. Click
2. Click Mouse (Hardware and Sound).
3. Click Finger Sensing Pad (tab) and click Configure.
4. Use the menu tree on the lef t to access the user configurable settings.
Start
, and click
Control Panel
(or point to
Settings
and click
Control Panel
).
2 - 8 Touchpad and Buttons/Mouse
Features & Components
Play Video
You can get a clearer
view of the gestures involved by clicking the
Play Video option for
each gesture item.
Figure 2 - 4
Finger Sensing
Pad - Gestures
Gestures
Click Gestures and make sure that the Enable Gestures tickbox is clicked. Doubleclick Gestures and then double-click Basic II or Applications to open the submenu. You can configure any of the gestures from these submenus.
2
Touchpad and Buttons/Mouse 2 - 9
Features & Components
Sound Volume
Adjustment
The sound volume level
is set using the volume
control within Windows
(and the volume function keys on the computer). Click the volume
icon in the taskbar to
check the setting.
Figure 2 - 5
VIA HD Audio Deck
Click Expert Mode to access the Advanced menus
2
Audio Features
You can configure the audio options on your computer from the Sound control
panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio
Deck control panel .
The volume may also be adjusted by means of the Fn + F5/F6 key combination.
2 - 10 Audio Features
Expert Mode will allow you to access more advanced configuration menus for
Syncing Left & Right
Volume
Balance
If you wish to adjust the left
and right channel volume
levels separately, you will
need to adjust this from the
VIA HD Audio Deck in Expert Mode.
Click Speaker in VIA HD
Audio Deck (in Expert
Mode) and click the Sync
Left and Right volume
button (see left). You can
then adjust the volume sliders independently (this setting also controls the
Balance setting in the Windows Sound control panel).
Figure 2 - 6
VIA HD Audio Deck
(Expert Mode)
Note that to adjust the Left & Right volume ba lance independently click th e Sync
Left and Right Volume icon (it should be faded) and adjust the slider as required.
Speaker, Microphone and Stereo Mix.
Features & Components
2
Audio Features 2 - 11
Features & Components
Parallel Printer
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
2
2 - 12 Adding a Printer
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most current printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instructions (unp acking, p aper tray, toner/ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar,
however you will need to purchase a parallel to USB converter.
Chapter 3: Power Management
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
• The Power Sources
• Turning On the Computer
• Power Plans
• Power-Saving States
• Configuring the Power Buttons
• Energy Star Power Saving
• Battery Information
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
3
Overview 3 - 1
Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. Attach the AC/DC adapter to the DC-in jack on the left of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button on the right side of the computer for about 2 - 3 seconds
to turn the computer “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 15).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 11.
3 - 2 The Power Sources
Turning On the Computer
Forced Off
If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the system to turn itself off.
Power Button as
Stand by or
Hibernate Button
You can use the OS’s
“Power Options” control
panel to set the power
button to send the system into Stand by or Hibernate mode (see your
OS’s documentation, or
“Configuring the Power Buttons” on page 3
- 8 for details).
Shut Down
Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk
or system problems.
Now you are ready to begin using your computer. To turn it on simply press the power button on the right side of the computer for about 2 - 3 seconds (note that the power LED on the front of the computer will turn from orange to green when the
computer powers on).
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.
Power Management
3
Turning On the Computer 3 - 3
Power Management
Resuming
Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 1
Power Plan
Advanced Settings
Power Plans
The computer can be configured to conserve power by means of power plans. You
3
can use (or modify) an existing power plan, or create a new one.
3 - 4 Power Plans
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Each Windows power plan will also adjust the processor performance of your ma-
Figure 3 - 2
Power Plans
Click to Show/Hide
additional
power plans
chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
Power Management
3
Power Plans3-5
Power Management
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where
3
you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.
If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.
3 - 6 Power-Saving States
Hibernate
Figure 3 - 3
Start Menu Power
Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.
Shut down
You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from Shut down takes longer than
from Sleep or Hibernate.
Power Management
3
Power-Saving States 3 - 7
Power Management
Password
Protection
It is recommended that
you enable a password
on wake up in order to
protect your data.
However you can disable this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that
are currently unavailable).
Figure 3 - 4
Power Options
Define Power
Buttons
3
Configuring the Power Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to a power-saving state. Click Choose what the power buttons do on
the left menu in Power Options to bring up the menu.
3 - 8 Configuring the Power Buttons
Resuming Operation
Closing the Lid
If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.
Table 3 - 1
Resuming
Operation
3.75G/HSPA
Modules & System
Wake Up
Note that the 3.75G modules
DO NOT
support
system wake up on
3.75G/HSPA modem activity.
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down
hot key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down).
You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status
Power Off Off Press the Power Button
Sleep Blinking Green
Hibernate
Display Turned Off Green Press a Key or Move the Mouse/Touchpad
Icon Color
Press the Sleep Button (Fn + F4 Key Combo)
Off (battery)
Orange (AC/DC adapter)
To Resume
Press the Power Button
Press the Power Button
Configuring the Power Buttons 3 - 9
Power Management
3
Power Management
Taskbar Icon
If the taskbar icon does
not appear then click the
taskbar arrow and select
Customize.
Select Show icon and
notifications alongside
the Hotkey icon and
click OK. The icon
will now appear in the
taskbar notification area.
Figure 3 - 5
Energy Star Menu
Conservation Modes
The default Energy Star setting
will result in maximum power saving, but with the possible loss of
some performance.
Setting the mode to Balance will
give power saving matched with
performance.
Performance will give optimum
computer performance but with
less power conservation.
Energy Star Power Saving
This system supports Energy Star power management features that place comput-
3
ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period
of inactivity. If you want to enable Energy Star power saving then follow these instructions:
3 - 10 Configuring the Power Buttons
1. Right-click the taskbar icon (see sidebar).
2. Select Power Conservation Modes.
3. Select Energy St ar to use the Energy Star power management and override other
power saving settings.
Battery Information
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 6
Battery Icon
(Taskbar) & Battery
Advanced Settings
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Change plan settings > Change advanced power settings (see Figure
3 - 2 on page 3 - 5).
Click the battery icon in the taskbar to see the current battery level and charge
status.
Power Management
3
Battery Information 3 - 11
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel
provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.
Figure 3 - 7
Windows Mobility
Center
3
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
• Close wireless, Bluetooth, modem or co mmunication applications when they are
not being used.
• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
3 - 12 Battery Information
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery”
on page 6 - 3.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 15 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 13 for information on the battery charge status, and to “Battery
FAQ” on page 3 - 15 for more information on how to maintain and properly re-
charge the battery pack.)
Power Management
3
Battery Information 3 - 13
Power Management
Caution
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
3
• DO NOT connect the metal terminals (+, -) to each other
3 - 14 Battery Information
Battery FAQ
Figure 3 - 8
Power Plan Create
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never.
Power Management
3
Battery Information 3 - 15
Power Management
Figure 3 - 9
Change Plan
Settings / Change
Advanced Power
Settings
3
3. Click Change plan settings (after creating it) and click Change plan settings >
Change advanced power settings.
3 - 16 Battery Information
4. Scroll down to Battery and click + to expand the ba ttery options.
Figure 3 - 10
Power Options
Advanced Settings -
Battery
5. Choose the options below (click Yes if a warning appears):
• Low battery levels = 0%
• Critical battery Levels = 1%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing
Power Management
3
Battery Information 3 - 17
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
3 - 18 Battery Information
Drivers & Utilities
Driver Installation & Power
When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power
source. Some drivers draw a significant am ou n t of power during the installation procedure, and if the remaining battery ca-
pacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue
involved here, and the battery will be rechargeable within 1 minute).
Chapter 4: Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of
the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system
components won’t be auto-configured with an appropriate driver or utility during operating system installation.
Instead, you need to manually install some system-required drivers and utilities.
What to Install
The Device Driv ers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper
operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to install and it is very important that
the drivers are installed in the order indicated (all drivers provided are for Windows 7 (32-bit Version Only).
The procedures for installing drivers for the PC Camera, Wireless LAN, 3.75G/HSPA and Bluetooth &
WLAN Combo modules are provided in “Modules & Options” on page 7 - 1.
4
What to Install 4 - 1
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
disc into an attached optical drive and click Install
Drivers/Option Drivers (button).
4
Follow the instructions to install the driver. Alternatively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions.
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, (you
should note down the drivers as you install them).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
Note: If you need to reinstall any driver, you should uninstall the
driver first.
Figure 4 - 1 - Drivers Installer Screen 1
4 - 2 Driver Installation
Figure 4 - 2 - Drivers Installer Screen 2
Driver - Windows 7 with Service
Pack 1
Chipset Page 4 - 5
Page #
Drivers & Utilities
Manual Driver Installation
Click Browse CD/DVD (button) in the Drivers Installer application and browse to the executable file in the
appropriate driver folder.
Video (VGA) Page 4 - 5
LAN Page 4 - 5
Card Reader Page 4 - 6
TouchPad Page 4 - 6
Hot Key Page 4 - 6
Audio Page 4 - 6
PC Camera Module Page 7 - 2
Wireless LAN Module Page 7 - 10
3.75G/HSPA Module Page 7 - 32
Bluetooth Module Page 7 - 56
Trusted Platform Module Page 7 - 71
Table 4 - 1 - Driver Installation
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest security
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows 7 Update” on page 4
- 7 for instructions.
Driver Installation 4 - 3
4
Drivers & Utilities
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
4
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as
outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2. Double-click Device Manager (Hardware and
Sound > Device Manager).
3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
User Account Control
If a User Account Control prompt appears as part of
the driver installation procedure, click Continue or
Allow, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or “Install” to continue the
installation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
4 - 4 Driver Installation
Drivers & Utilities
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter
(and in Chapter 7 Options & Modules), are accurate at
the time of going to press.
Drivers are always subject to upgrade and revision so
the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish)
unless you are an advanced user. In many cases a restart is required to install the driver.
Make sure any modules (e.g. PC Camera, WLAN,
3.75G/HSPA or Bluetooth Combo) are ON before installing the appropriate driver.
New Hardware Found
If you see the message “New Hardware Found” dur-
ing the installation procedure (other than when out-
lined in the driver install procedure), click Cancel
to close the window, and follow the installation procedure.
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
disc into your attached CD/DVD drive and click In-
stall Drivers (button).
Chipset
1. Click 1.Install Chipset Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Video (VGA)
1. Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
LAN
1. Click 3.Install LAN Driver > Yes.
2. Click Install > Finish to complete the installa-
tion.
3. The network settings can now be configured.
4
Driver Installation 4 - 5
Drivers & Utilities
Card Reader
1. Click 4.Install Cardreader Driver > Yes.
2. Click Install > Finish to complete the installa-
tion.
4
TouchPad
1. Click 5.Install Touchpad Driver > Yes.
2. Click Next.
3. Click the button to accept the license agreement
and click Next.
4. Click Finish > Restart Now to restart the com-
puter.
Hot Key
1. Click 6.Install HotKey AP > Yes.
2. Click Next > Next.
3. Click Finish > Finish to restart the computer.
Audio
1. Click 7.Install Audio Driver > Yes.
2. Click Next.
3. Click the button to agree to the license and
click Next.
4. Click Next > Next > Next.
5. Click Finish to restart the computer.
(see over)
Note that after installing the audio driver the system
will not return to the Drivers Installer screen. To in-
stall any of the optional drivers listed overleaf, eject
the Device Drivers & Utilities + User’s Manual disc
and then reinsert it (or double-click the disc icon in My
Computer), and click Option Drivers (button) to ac-
cess the optional driver menu.
4 - 6 Driver Installation
Windows Experience Index
Windows 7 Update
After installing all the drivers make sure you enable Windows Update in order to get all the latest security up-
dates etc. (all updates will include the latest hotfixes
from Microsoft).
To enable Windows Update make sure you are con-
nected to the internet:
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2. Click Window s Update (System and Security).
3. Click Check for updates (button).
4. The computer will now check for updates (you
need to be connected to the internet).
5. Click Install now (button) to begin checking for the
updates.
6. Click Install updates (button) to install the
updates.
After the drivers are installed follow this procedure to
ensure an accurate rating from the Windows Experi-
ence Index:
Drivers & Utilities
1. Click Start, and click Control Panel.
2. Click Performance Information and Tools
3. Click “Rate this computer”.
4. The computer will take a few minutes to assess
5. Close the control panel.
(System and Security > System > Check the
Windows Experience Index).
the system performance.
4
Driver Installation 4 - 7
Drivers & Utilities
Optional Drivers
See the pages indicated in Table 4 - 1, on page 4 - 3 for the driver installation procedures for any modules included in your purchase option.
4
Figure 4 - 3 - Drivers Installer - Option Drivers Menu
Make sure any modules (e.g. PC Camera, WLAN, 3.75G/HSPA or Bluetooth) are ON before installing the appropriate driver.
4 - 8 Driver Installation
Chapter 5: BIOS Utilities
BIOS Screens
Note that the BIOS
screens pictured on
these pages are intended for guidance in setting up your system’s
BIOS.
BIOS versions are subject to constant change
and revision, therefore
your computer’s actual
screens may appear
slightly different from
those pictured on these
pages.
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Phoenix SecureCore Tiano Setup
If your computer has never been set up, or you are making impo rtant changes to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your
system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Utilities
5
Overview 5 - 1
BIOS Utilities
POST Screen
1.BIOS information
2.CPU type
3.Memory status
4.Enter Setup prompt
appears only during
POST
Note:
The
POST
screen
as pictured right is for
guideline purposes only.
The
POST
screen on
your computer may appear slightly different. If
you disable the
Boot-
time Diagnostic Screen
,
the POST screen will not
appear.
Figure 5 - 1
POST Screen
1
2
3
4
5
The Power-On Self Test (POST)
Each time you turn on the computer, the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.
5 - 2 The Power-On Self Test (POST)
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:
• Press <F1> to resume
• <F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct
configuration.
BIOS Utilities
5
Press F2 to run the Setup program and try to correct the problem. If you still get an
error message after you change the setting, or if the “cure” seems even worse, call
for help.
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
The Setup Utility
The Phoenix SecureCore Tiano Setup tells the system how to configure itself and
manage basic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The prompt
(Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds
after you turn on the system. If you get a “Keyboard Error”, (usually because you
pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.
5 - 4 The Setup Utility
Setup Screens
Setup Menus
The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configuration appropriate for your
model and options.
The following pages contain additional advice on portions of the Phoenix SecureCore Tiano Setup.
Along the top of the screen is a menu bar with menu headings. When you select a
heading, a new screen appears. Scroll through the features listed on each screen to
make changes to Phoenix SecureCore Tiano Setup.
Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
BIOS Utilities
5
The Setup Utility 5 - 5
BIOS Utilities
Figure 5 - 2
Main Menu
Main Menu
5
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
5-6Main Menu
System / Total Memory (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
MB Series / BIOS Version / KBC/EC Firmware Revision (Main Menu)
This item contains information on the current BIOS and firmware versions.
BIOS Utilities
5
Main Menu 5 - 7
BIOS Utilities
SATA Controller
Mode
If you have installed the
Windows 7 operating
system with AHCI mode
enabled (default setting),
DO NOT disable AHCI
mode (if you wish to disable AHCI mode you will
need to reinstall the Win-
dows 7 OS).
Figure 5 - 3
Advanced Menu
5
Advanced Menu
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)
You can use this item Enable/Disable power to the Bluetooth module if you wish to
save system power.
SATA Controller Mode (Advanced Menu)
You can configure SATA (Serial ATA) control to operate in IDE (native/compatible), AHCI (Advanced Host Controller Interface) modes from this menu. The
SATA Mode should be set BEFORE installing an operating system, and after you
have backed up all necessary files and data (see sidebar).
5 - 8 Advanced Menu
Diagnostic Splash Screen (Advanced Menu)
Use this menu item to enable/disable the Boot-time Diagnostic Screen or POST
screen (see “The Power-On Self Test (POST)” on page 5 - 2).
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
BIOS Utilities
Battery Low Alarm Beep (Advanced Menu)
Use this menu item to enable/disable the audible warning when the battery has
reached low power status.
5
Advanced Menu 5 - 9
BIOS Utilities
Security Menu
The changes you make
here affect the access
to the Setup utility itself,
and also access to your
machine as it boots up
after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in your
software OS.
Figure 5 - 4
Security Menu
Security Menu
5
5 - 10 Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the Phoenix SecureCore Tiano Setup. This
will not affect access to the computer OS (only the Phoenix SecureCore Tiano Set-
up).
Set User Password (Security Menu)
Password Warning
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
TPM Password
Note that you should set
a supervisor password
in the BIOS to protect
the TPM information
from being tampered
with by unauthorized users.
You can set a password for user mode access to the Phoenix SecureCore Tiano Setup. This will not affect access to the computer OS, (only the Setup utility) unless
you choose to set a Password on Boot (see below). Many menu items in the Phoenix
SecureCore Tiano Setup cannot be modified in user mode. You can only set the
user password after you have set the supervisor password.
BIOS Utilities
Password on boot (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may
only set a password on boot if a supervisor password is enabled). If “Enabled”
is selected, only users who enter a correct password can boot the system (see the
warning in the sidebar). The default setting is “Disabled”.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter
again to confirm the password clearance.
TPM (Trusted Platform Module) Support: (Security Menu)
The TPM security chip allows you to create and manage digital certificates for user
and platform authentication. Enable TPM Support from this menu, and the TPM
State menu will then appear (see “TPM State” on page 5 - 12). Note: If you disable
TPM Support then your TPM information may be erased altogether. You should
only disable TPM support when you need to clear the TPM information. The default
setting is “Disabled”.
5
Security Menu 5 - 11
BIOS Utilities
TPM State Menu
To access this menu
you must first enable
TPM support from the
security menu (see
page 5 - 10).
Password
Protection
Note that you should set
a supervisor password
in the BIOS to protect
the TPM information
from being tampered
with by unauthorized users.
Figure 5 - 5
TPM State
5
TPM State
Change TPM State (TPM State)
This menu allows you to set the level of TPM functionality. You can enable/disable
the TPM function altogether, or clear all existing TPM information.
5 - 12 TPM State
Note: If you clear all TPM information it will be erased altogether and the information will need to be reconfigured.
Loading...