Clevo W170ER User guide

V12.2.20
Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©May 2012
Trademarks
Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc­tive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux­embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov­enia.
EuP-Standby and Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode or standby mode:
Standby Mode < 2W
Off Mode < 1W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has at­tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the service representative or an experienc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference. And
2. This device must accept any interference, including interfer ence that may cause undesired operation of the
device.
IV
FCC RF Radiation Exposure Statement:
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Preface
V
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit with an AC Input of 100 - 240V, 50 - 60Hz, DC
Output of 19V, 4.74A (90 Watts) minimum AC/DC Adapter.
VI
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer to any shock or vibration.
Do not place it on an unstable surface.
Do not place anything heavy on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.
Do not expose it to excessive heat or direct sunlight.
Do not leave it in a place where foreign matter or mois­ture may affect the system.
Don’t use or store the com­puter in a humid environment.
Do not place the computer on any surface that will block the Vents/Fan Intakes.
VII
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until you properly shut down all programs.
Do not turn off any peripheral devices when the computer is on.
5. Take care when using peripheral devices.
Use only approved brands of peripherals.
VIII
Do not disassemble the com­puter by yourself.
Unplug the power cord befor e attaching peripheral devices.
Perform routine maintenance on your computer.
Power Safety
Power Safety
Warning
Before you undertake any upgrade proce­dures, make sure that you have turned off the power, and discon­nected all peripherals and cables (including telephone lines and power cord).
You must also remove your battery in order to prevent accidentally turning the machine on. Before removing
the battery discon­nect the AC/DC adapter from the computer.
The computer has specific power requirements:
Only use a power adapter approved for use with this computer.
Your AC/DC adapter may be designed for international travel but it still requires a
steady , uninterru pted power suppl y. If you are unsure of your local power specifications, consult your service representative or local power company.
The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power cord if you are wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
Preface
IX
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.
Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha-
nism and is not a cause for concern.
Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-
ture environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
X
Battery Precautions
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
Do not remove any batteries from the computer while it is powered on.
Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
If you do not use the battery for an extended period, then remove the battery from the computer for storage.
Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu al-
ified service personnel.
Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
Keep the battery away from metal appliances.
Affix tape to the battery contacts before disposing of the battery.
Do not touch the battery contacts with your hands or metal objects.
Preface
XI
Preface
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.
Also note the following when the cover is removed:
Hazardous moving parts.
Keep away from moving fan blades.
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
When the power cord or AC/DC adapter is damaged or frayed.
If the computer has been exposed to rain or other liquids.
If the computer does not work normally when you follow the operating instructions.
If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
If there is an unusual odor, heat or smoke coming from your computer.
XII
Preface
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prev ent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your documents are prepared.
XIII
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knock­ing the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com­puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.
XIV
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
Adjust the height of the chair and /or desk so that the ke yboard is a t or slightly below the level
of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Your knees should be slight ly higher than your hips. Place your feet flat on the floor or on a
footrest if necessary.
Use a chair with a back and adjust it to support your lower back comfortably.
Sit straight so that your knees, hips and elbows form approximately 90-degree angles when
you are working.
Take periodic breaks if you are using the computer for long periods of time.
Remember to:
Alter your posture frequently.
Stretch and exercise your body several times a day.
Take periodic breaks when you work at the computer for long periods of time. Frequent and
short breaks are better than fewer and longer breaks.
XV
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
Position the display directly in front of you at a comfortable viewing distance.
Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:
Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
Rotate desktop background images every few days.
Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your service center.
XVI
Preface
Contents
Notice .............................................................................................................................................................I
EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II
FCC Statement ............................................................................................................................................IV
FCC RF Radiation Exposure Statement: .....................................................................................................V
Instructions for Care and Operation ......................................................................................................... VII
Power Safety ...............................................................................................................................................IX
Polymer Battery Precautions .......................................................................................................................X
Battery Precautions .....................................................................................................................................XI
Cleaning .................................................................................................................................................... XII
Servicing ................................................................................................................................................... XII
Travel Considerations ..............................................................................................................................XIII
Quick Start Guide
Overview ....................................................................................................................................................1-1
Advanced Users .........................................................................................................................................1-2
Beginners and Not-So-Advanced Users ....................................................................................................1-2
Warning Boxes ..........................................................................................................................................1-2
Not Included ..............................................................................................................................................1-3
System Startup ...........................................................................................................................................1-4
System Software ........................................................................................................................................1-5
System Map: LCD Panel Open ..................................................................................................................1-6
XVII
Preface
LED Indicators ...........................................................................................................................................1-7
Keyboard ....................................................................................................................................................1-8
Function/Hot Key Indicators .....................................................................................................................1-9
Control Center .........................................................................................................................................1-10
System Map: Front & Rear Views ...........................................................................................................1-11
System Map: Left View ...........................................................................................................................1-12
System Map: Right View .........................................................................................................................1-13
System Map: Bottom View .....................................................................................................................1-14
Windows 7 Start Menu & Control Panel .................................................................................................1-15
Video Features .........................................................................................................................................1-16
NVIDIA® Optimus™ Technology .........................................................................................................1-16
Power Options .........................................................................................................................................1-20
Features & Components
Overview ....................................................................................................................................................2-1
Hard Disk Drive .........................................................................................................................................2-2
Multi-In-1 Card Reader .............................................................................................................................2-3
Touchpad and Buttons/Mouse ...................................................................................................................2-4
Gestures and Device Settings ....................................................................................................................2-5
Audio Features ...........................................................................................................................................2-8
Power Management
Overview ....................................................................................................................................................3-1
XVIII
Preface
The Power Sources ....................................................................................................................................3-2
AC/DC Adapter .........................................................................................................................................3-2
Battery ........................................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-3
Power Plans ...............................................................................................................................................3-4
Power-Saving States ..................................................................................................................................3-6
Sleep ..........................................................................................................................................................3-6
Hibernate ....................................................................................................................................................3-7
Shut down ..................................................................................................................................................3-7
Configuring the Power Buttons .................................................................................................................3-8
Resuming Operation ..................................................................................................................................3-9
Power Conservation Modes .....................................................................................................................3-10
Battery Information .................................................................................................................................3-11
Conserving Battery Power .......................................................................................................................3-12
Battery Life ..............................................................................................................................................3-13
New Battery .............................................................................................................................................3-13
Recharging the Battery with the AC/DC Adapter ...................................................................................3-13
Proper handling of the Battery Pack ........................................................................................................3-14
Battery FAQ .............................................................................................................................................3-15
Drivers & Utilities
What to Install ............................................................................................................................................4-1
XIX
Preface
Driver Installation ......................................................................................................................................4-2
Updating/Reinstalling Individual Drivers ..................................................................................................4-4
User Account Control ................................................................................................................................4-5
Windows Security Message .......................................................................................................................4-5
New Hardware Found ................................................................................................................................4-5
Driver Installation Procedure .....................................................................................................................4-6
Chipset .......................................................................................................................................................4-6
Video (VGA) .............................................................................................................................................4-6
NVIDIA Video (VGA) ..............................................................................................................................4-6
LAN ...........................................................................................................................................................4-6
CardReader ................................................................................................................................................4-6
Touchpad ...................................................................................................................................................4-6
Hot Key ......................................................................................................................................................4-7
USB 3.0 ......................................................................................................................................................4-7
MEI Driver .................................................................................................................................................4-7
Audio .........................................................................................................................................................4-7
Windows Experience Index .......................................................................................................................4-8
Optional Drivers ........................................................................................................................................4-9
BIOS Utilities
Overview ....................................................................................................................................................5-1
The Setup Utility ........................................................................................................................................5-2
XX
Preface
Failing the POST .......................................................................................................................................5-3
Fatal Errors ................................................................................................................................................5-3
Non-Fatal Errors ........................................................................................................................................5-3
Setup Screens .............................................................................................................................................5-4
Main Menu .................................................................................................................................................5-5
System Time & Date (Main Menu) ...........................................................................................................5-5
SATA Port # (Main Menu) ........................................................................................................................5-6
System/Extended Memory: (Main Menu) .................................................................................................5-6
MB Series / BIOS Revision / KBC/EC firmware Revision ......................................................................5-6
Advanced Menu .........................................................................................................................................5-7
Advanced Chipset Control (Advanced Menu) ..........................................................................................5-7
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-8
Intel Smart Connect Technology (Advanced Menu) .................................................................................5-8
Intel Anti-Theft Technology (Advanced Menu) ........................................................................................5-8
SATA Mode Selection (Advanced Menu) ................................................................................................5-8
Boot Logo (Advanced Menu) ....................................................................................................................5-9
Power On Boot Beep (Advanced Menu) ...................................................................................................5-9
Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9
Security Menu ..........................................................................................................................................5-10
Set Supervisor Password (Security Menu) ..............................................................................................5-10
Set User Password (Security Menu) ........................................................................................................5-11
Password on boot (Security Menu) ..........................................................................................................5-11
XXI
Preface
Boot Menu ...............................................................................................................................................5-12
Boot Sequence (Boot Menu) ...................................................................................................................5-13
Exit Menu ................................................................................................................................................5-14
Upgrading The Computer
Overview ....................................................................................................................................................6-1
When Not to Upgrade ................................................................................................................................6-2
Removing the Battery ................................................................................................................................6-4
Installing the Battery ..................................................................................................................................6-5
Removing the Component Bay Cover .......................................................................................................6-6
Replacing the Component Bay Cover .......................................................................................................6-7
Upgrading the Hard Disk Drive .................................................................................................................6-8
Upgrading the System Memory (RAM) ..................................................................................................6-11
Modules & Options
Overview ....................................................................................................................................................7-1
PC Camera Module ....................................................................................................................................7-2
PC Camera Driver Installation ...................................................................................................................7-3
Wireless LAN Module .............................................................................................................................7-10
3rd Party 802.11b/g/n Driver Installation (for WLAN Module) .............................................................7-11
3rd Party 802.11b/g/n Driver Installation (for Combo Modules) ............................................................7-12
Intel® WLAN Driver Installation ............................................................................................................7-13
Connecting to a Wireless Network in Windows 7 ...................................................................................7-16
XXII
Preface
Connecting to a Wireless Network Using Intel® PROSet Wireless .......................................................7-19
Intel® My WiFi Configuration ................................................................................................................7-21
Windows Mobility Center .......................................................................................................................7-30
Intel® Wireless Display Application .......................................................................................................7-31
Intel® WiDi Application Installation ......................................................................................................7-32
Intel® Wireless Music Driver Installation ...............................................................................................7-32
Intel® WiDi Application Configuration ..................................................................................................7-33
Bluetooth & WLAN Combo Module ......................................................................................................7-36
3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-37
Intel Bluetooth Combo Driver Installation ..............................................................................................7-38
Standard Bluetooth Configuration in Windows 7 ...................................................................................7-39
THX TruStudio Pro Audio ......................................................................................................................7-43
THX TruStudio AP Installation ...............................................................................................................7-43
THX TruStudio Pro Activation ...............................................................................................................7-44
THX TruStudio Pro Application .............................................................................................................7-44
Intel Rapid Storage Technology ..............................................................................................................7-48
IRST Driver Installation ..........................................................................................................................7-48
Intel® Smart Connect Technology ..........................................................................................................7-49
Intel Smart Connect Technology Driver Installation ...............................................................................7-49
Intel® Smart Connect Technology Configuration ...................................................................................7-50
XXIII
Preface
Troubleshooting
Overview ....................................................................................................................................................8-1
Basic Hints and Tips ..................................................................................................................................8-2
Backup and General Maintenance .............................................................................................................8-3
Viruses .......................................................................................................................................................8-4
Upgrading and Adding New Hardware/Software ......................................................................................8-5
Problems and Possible Solutions ...............................................................................................................8-7
Bluetooth Connection Problems ..............................................................................................................8-12
Interface (Ports & Jacks)
Overview ...................................................................................................................................................A-1
Notebook Ports and Jacks .........................................................................................................................A-2
Control Center
Overview ...................................................................................................................................................B-1
Video Driver Controls
NVIDIA Video (VGA) .............................................................................................................................C-1
Specifications
Processor ...................................................................................................................................................D-2
Processor ...................................................................................................................................................D-2
Processor ...................................................................................................................................................D-2
XXIV
Preface
Processor ...................................................................................................................................................D-3
Core Logic ................................................................................................................................................D-3
Display ......................................................................................................................................................D-3
Memory .....................................................................................................................................................D-3
Video Adapter ...........................................................................................................................................D-3
Storage ......................................................................................................................................................D-3
Keyboard & Pointing Device ....................................................................................................................D-3
Audio ........................................................................................................................................................D-3
Interface ....................................................................................................................................................D-3
Card Reader ..............................................................................................................................................D-4
Slot ............................................................................................................................................................D-4
Communication .........................................................................................................................................D-4
Communication .........................................................................................................................................D-4
Power Management ..................................................................................................................................D-4
Power ........................................................................................................................................................D-4
Indicators ..................................................................................................................................................D-4
Operating System ......................................................................................................................................D-4
BIOS .........................................................................................................................................................D-4
Security .....................................................................................................................................................D-4
Environmental Spec ..................................................................................................................................D-4
Features .....................................................................................................................................................D-5
Dimensions & Weight ..............................................................................................................................D-5
XXV
Preface
XXVI
Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk &
card reader) Touchpad & Mouse and Audio.
Chapter 3 The computer’s power saving options.
Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
Chapter 6 Instructions for upgrading your computer.
Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth and Intel modules (some
of which may be optional depending on your purchase configuration).
Chapter 8 A troubleshooting guide.
Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
Appendix B Information on the Control Center .
Appendix C Information on the video driver controls.
Appendix D The computer’s specification.
1
Overview 1 - 1
1
Notes
Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a
of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in the Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com­puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you); refer to
Chapter 4 for installation instructions.
Ports and Jacks
See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com­puter to communicate with external devices, connect to the internet etc.

Not Included

Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
1
Overview 1 - 3
1
Shutdown
Note that you should al­ways shut your comput­er down by choosing the Shut Down command from the bottom right of the Start menu in Win- dows. This will help prevent hard disk or system problems.
130°
Quick Start Guide

System Startup

1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Use one hand to raise the
hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by the lid/LCD).
lid/LCD to a comfortable viewing angle (
Figure 1 - 1 - Opening the Lid/LCD & Computer with AC/DC Adapter Plugged-In
do not exceed 130 degrees
);
use the other
1 - 4 System Startup
Quick Start Guide
Windows OS
In order to run Windows 7 without limitations or decreased performance, your computer requires a minimum 1GB of sys­tem memory (RAM), however if you are running Windows 7 64 bit your computer requires a minimum 2GB of system memory (RAM).

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find that this manual refers to the Windows 7 operating system.
1
System Startup 1 - 5
1
Figure 1 - 2
LCD Panel Open
1. Built-In PC Camera (
Optional
)
2. Built-In Microphone
3. LCD
4. LED Indicators
5. Power Button
6. Keyboard
7. Touchpad & Buttons
Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above.
2
4
1
3
5
Wireless Device
Operation Aboard
Aircraft
The use of any portable elec­tronic transmission devices aboard aircraft is usually pro­hibited. Make sure the mod­ule(s) are OFF if you are using the computer aboard aircraft.
Use the key combinations (or
WLAN Switch for wireless LAN only) to toggle power to the WLAN/Bluetooth and
3.75G modules, and check
the LED indicator or on­screen icon to see if the mod­ules are powered on or not (see Table 1 - 2, on page 1 -
9/ Table 1 - 1, on page 1 - 7).
6
7
Quick Start Guide
1 - 6 System Map: LCD Panel Open

System Map: LCD Panel Open

Quick Start Guide

LED Indicators

The LED indicators on the computer display helpful information about the current status of the computer.
Icon Color Description Icon Color Description
Orange DC Power is Plugged In Blue Power Button
1
Blinking Orange
Green The Computer is On Green Hard Disk Activity
Blinking Green
Orange The Battery is Charging Orange
Green The Battery is Fully Charged
Blinking Orange
The Powered USB Port is
On*
The Computer is in Sleep
Mode
The Battery has Reached
Critically Low Power Status
Green
Table 1 - 1 - LED Indicators
The (optional) Wireless LAN
Module is Powered On
The (optional) Bluetooth
Module is Powered On
*Note: The powered USB 2.0 port (see Figure 1 - 6 on page 1 - 13) may be toggled on /off by means of the Fn + Power Button key combination. When the powered USB port is on it will supply powe r ( for charging devices only, not for op­erating devices) when the system is off but still powered by the AC/DC ada pter plugged into a working o utlet, or powered
by the battery with a capacity level above 20% (this may not work with certain devices - see page 8 - 11).
LED Indicators 1 - 7
1
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will de­tect and enable it automatically. However special functions/hot­keys unique to the system’s reg­ular keyboard may not work.
Play/Pause Key
Function Keys
NumLk & ScrLk Keys
Toggle Key
3.75G/HSPA Module Power
Fn Key
Numerical Keypad
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters. These special char­acters can only be produced by using the numeric keypad. Regular number keys (in the upper row o f the keyboard) will not work. Make sure that NumLk is on.
Quick Start Guide

Keyboard

The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 2, on page 1 - 9 for details on the function keys.
Figure 1 - 3 - Keyboard
1 - 8 Keyboard
Quick Start Guide

Function/Hot Key Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility is installed.
Keys Function Keys Function
1
Fn + Power
Button
Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F10 PC Camera Power Toggle
Fn + F1 TouchPad Toggle Fn + F11 WLAN Module Power Toggle
Fn + F2
Fn + F3 Mute Toggle
Fn + F4 Sleep Toggle Fn + ScrLk Scroll Lock Toggle
Fn + F5/F6
Fn + F7 Display Toggle
Powered USB 2.0 Port Power Toggle Fn + F8/F9
(Press a key to or use TouchPad to turn on)
Volume Decrease/
Increase
Turn LCD Backlight Off
Fn + F12
Fn +
NumLk
Caps Lock Caps Lock Toggle
Fn + Esc Control Center Toggle (see over)
Brightness Decrease/
Increase
Bluetooth Module Power
Toggle
Number Lock Toggle
Table 1 - 2 - Function & Hot Key Indicators
Function/Hot Key Indicators 1 - 9
1

Control Center

Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.
Click on the power conservation modes to switch be­tween Performance, Balanced or Energy Star modes (see page 3 - 10). To remove the Power Conservation Modes screen just click in a blank area of the icon or press a key on the keyboard.
Click on the buttons (or just click and hold the mouse but­ton) to adjust the slider for Brightness/Volume.
Click on Display Switch and click to choose a display mode from the menu (see page C - 12).
Quick Start Guide
Control Center
Press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and en­ables you to quickly turn modules on/off.
1 - 10 Control Center
Table 1 - 3 - Control Center

System Map: Front & Rear Views

Figure 1 - 4
Front & Rear Views
1. LED Indicators
2. Multi-In-1 Card Reader
3. Battery
Multi-In-1 (Push-Push) Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RS MMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
MS (Memory Stick) / MS Pro / MS Duo
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial dis­charges.
3
1
2
Quick Start Guide
1
System Map: Front & Rear Views 1 - 11
1
Figure 1 - 5
Left View
1. RJ-45 LAN Jack
2. External Monitor Port
3. HDMI-Out Port
4. Headphone-Out Jack
5. Microphone-In Jack
6. Vent/Fan Intake
7. 2 * USB 3.0 Ports
2
54
1
3
7
6
USB 3.0 Ports
USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. Note th at the USB
3.0 port requires a driver installation (see “USB 3.0” on page 4 - 7), does not support wake on USB and is not operational under DOS.
Optical Device Drives
To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports.
Quick Start Guide

System Map: Left View

1 - 12 System Map: Left View

System Map: Right View

Figure 1 - 6
Right View
1. Security Lock Slot
2. 1 * Powered USB
2.0 Port
3. DC-In Jack
Optical Device
Drives
To install applications and drivers etc. you will need to attach an exter­nal optical CD/DVD de­vice to the USB ports.
Powered USB 2.0 Port
The powered USB 2.0 port can supply power (for charging devices only, not for op­erating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with certain devices). Toggle power to this port by using Fn + power button.
2
1
2
3
Quick Start Guide
1
System Map: Right View 1 - 13
1
Figure 1 - 7
Bottom View
1. Battery
2. Speakers
3. Fan Intake/Vent
4. Multi-In-1 Card Reader
Battery Information
Always completely dis­charge, then fully charge, a new battery before using it. Com­pletely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
2
1
4
3
3
3
3
CPU
The CPU is not a user serviceable part.
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
2
Quick Start Guide

System Map: Bottom View

1 - 14 System Map: Bottom View
Quick Start Guide
Figure 1 - 8 - Start Menu & Control Panel
Click here to toggle Category View

Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac­cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View to view the control panel icons.
Windows 7 Start Menu & Control Panel 1 - 15
1
1
Quick Start Guide

Video Features

NVIDIA® Optimus Technology

NVIDIA® Optimus technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. The computer will auto- matically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use.
You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows 7 (see over). For more detailed video information see “Video Driver Con-
trols” on page C - 1.
1 - 16 Video Features
To access Display (Control Panel) and Screen Resolution in Windows:
1
2
1
2
1. Click Start and click Control Panel.
2. Click Display (icon) - In the Appearances and Personalization category.
3. Click Adjust Screen Resolution/Adjus t resolution.
4. Alternatively you can right-click the desktop and select Screen resolution.
5. Use the dropbox to select the screen Resolution (Figure 1 - 9).
6. Click Advanced settings (Figure 1 - 9) to bring up the Advanced properties tabs.
Quick Start Guide
1
Figure 1 - 9 - Screen Resolution
Video Features 1 - 17
1
234
3
4
Quick Start Guide
To access the Intel(R) Graphics and Media Control Panel:
1. Click Advanced settings (Figure 1 - 9 on page 1 - 17) in the Display Settings control panel in Windows.
2. Click Graphics Properties (button) (Figure 1 - 10) in the Intel Graphics & Media Control Panel tab.
OR
3. Right-click the desktop and select Graphics Properties from the menu.
OR
4. Click the icon (Figure 1 - 10) in the taskbar and select Graphics Properties from the menu.
OR
5. Access the Intel(R) Graphics and Media Control Panel from the Windows control panel in Classic V iew.
6. Choose the application mode (Basic, Advanced or Wizard) required.
Figure 1 - 10 - Intel Graphics and Media Control Panel
1 - 18 Video Features
To access the NVIDIA Control Panel:
5
6
5
6
1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 11).
OR
2. Double-click the icon (Figure 1 - 11) in the Windows control panel.
Quick Start Guide
1
Figure 1 - 11 - NVIDIA Control Panel
Video Features 1 - 19
1
Quick Start Guide

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 14 ) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change plan settings and click Change advanced power settings to access further con­figuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 11.
1 - 20 Power Options
Figure 1 - 12 - Power Options
Features & Components
External Optical
(CD/DVD) Device
Drives
To install applications and drivers etc. you will need to attach an exter­nal optical CD/DVD de­vice to the USB ports.

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components of the computer:
•Hard Disk Drive
Multi-In-1 Card Reader
Touchpad and Buttons/Mouse
Audio Features
2
Overview 2 - 1
Features & Components
Power Safety
Before attempting to ac­cess any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the ma­chine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.
Figure 2 - 1
Hard Disk Location
HDD Bay
2

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
The hard disk is accessible from the bottom of your computer as seen below. For fur- ther details see “Upgrading the Hard Disk Drive” on page 6 - 8.
2 - 2 Hard Disk Drive
Features & Components
Card Reader Cover
Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust get­ting in to the card read­er.
Push-Push Card
Reader
The card reader fea­tures a push-in/push-out card insertion and ejec­tion mechanism. Simply push the card to insert and eject it, however Ms Duo cards require an adapter.
Figure 2 - 2
Front View
1. Card Reader
MMC (MultiMedia Card) / RS MMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
MS (Memory Stick) / MS Pro / MS Duo
1

Multi-In-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the card reader driver (see
“CardReader” on page 4 - 6.
Note: Some of these cards require PC adapters that are usually supplied with the cards.
2
Multi-In-1 Card Reader 2 - 3
Features & Components
Touchpad Scrolling
This computer model se­ries may feature different Touchpad versions.
These Touchpads may differ in their vertical scrolling function in most scrollable windows.
Some Touchpads require sliding the finger up and down on the right of the Touchpad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the Touchpad to scroll the window.
Figure 2 - 3
Mouse Properties
2

Touchpad and Buttons/Mouse

The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.
Once you have installed the Touchpad driver (see “Touchpad” on page 4 - 6) you can configure the functions by double-clicking the Touchpad driver icon in the notification area. You may then configure the Touchpad tapping, buttons, scrolling (see sidebar), pointer motion and sensitivity options to your preferences.
2 - 4 Touchpad and Buttons/Mouse
Features & Components
Show Video
You can get a clearer view of the gestures in­volved by clicking the Show Video option for each gesture item.
Select the gesture (Pinch
Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Set­tings left tree menu
and click the Show Video button to see the demon­stration video.
For more details on any of the gestures see the help in the lower part of the right menu window.
Figure 2 - 4
Mouse Properties -
Device Settings

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (ac­tion) on the surface of the Touchpad to perform specific actions to manipulate doc­uments, objects and applications.
You can configure the settings from the Device Settings tab in Mouse Properties:
1. Click
2. Click Mouse (Hardware and Sound).
3. Click Device Settings (tab) and click Settings.
4. Use the menu tree on the left to access the user configurable settings.
Start
, and click
Control Panel
(or point to
Settings
and click
Control Panel
2
).
Touchpad and Buttons/Mouse 2 - 5
Features & Components
Figure 2 - 5
Scrolling Gesture
Mouse Driver
If you are using an ex­ternal mouse your op­erating system may be able to auto-configure your mouse during its installation or only en­able its basic functions. Be sure to check the device’s user docu­mentation for details.
Figure 2 - 6
Zooming Gesture
2
Scrolling
The Two-Finger scrolling feature works in most scrollable windows an d allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the Touchpad surface and slide both fingers in the direction required (in a straight con­tinuous motion).
2 - 6 Touchpad and Buttons/Mouse
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality. Place two fingers on the Touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.
Rotating
Figure 2 - 7
Rotating Gesture
Figure 2 - 8
Flick/Press
Gesture
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the Touchpad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The Three Fingers Down gesture may be used to launch user-selectable applications.
Features & Components
2
Touchpad and Buttons/Mouse 2 - 7
Features & Components
Sound Volume
Adjustment
The sound volume level is set using the volume control within Windows (and the volume func­tion keys on the comput­er). Click the volume icon in the taskbar to check the setting.
Figure 2 - 9
VIA HD Audio Deck
Click Expert Mode to access the Advanced menus
2

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, from the HD VDeck icon on the desktop or VIA HD Audio Deck control panel .
The volume may also be adjusted by means of the Fn + F5/F6 key combination.
2 - 8 Audio Features
Expert Mode will allow you to access more advanced configuration menus for
Syncing Left & Right
Volume
Balance
If you wish to adjust the left and right channel volume levels separately, you will need to adjust this from the
VIA HD Audio Deck in Ex­pert Mode.
Click Speaker in VIA HD Audio Deck (in Expert Mode) and click the Sync Left and Right volume
button (see left). You can then adjust the volume slid­ers independently (this set­ting also controls the Balance setting in the Win­dows Sound control pan­el).
Figure 2 - 10
VIA HD Audio Deck
(Expert Mode)
Note that to adjust the Left & Right volume ba lance independently click th e Sync Left and Right Volume icon (it should be faded) and adjust the slider as required.
Speaker, Microphone and Stereo Mix. Also see “THX TruStudio Pro Audio” on page 7 - 43 for more audio configuration
information.
Features & Components
2
Audio Features 2 - 9
Features & Components
2
2-10

Chapter 3: Power Management

OS Note
Power management functions will vary slight­ly depending on your operating system. For more information it is best to refer to the user’s manual of your operat­ing system.
(Note: All pictures used on the following pages are from the Windows 7 OS.)
Power Management

Overview

To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer (the LCD and hard disk drive) or the whole system. This chapter covers:
The Power Sources
Turning On the Computer
Power Plans
Power-Saving States
Configuring the Power Buttons
Power Conservation Modes
Battery Information
The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.
3
Overview 3 - 1
Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.
3

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.
1. Attach the AC/DC adapter to the DC-in jack on the right of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 15).
We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Battery Information” on page 3 - 11.
3 - 2 The Power Sources

Turning On the Computer

Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the sys­tem to turn itself off.
Power Button as
Stand by or
Hibernate Button
You can use the OS’s Power Options control panel to set the power button to send the sys­tem into Stand by or Hi­bernate mode (see your OS’s documentation, or
“Configuring the Pow­er Buttons” on page 3
- 8 for details).
Shut Down
Note that you should always shut your computer down by choosing the Shut Down com­mand from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.
Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.
Power Management
3
Turning On the Computer 3 - 3
Power Management
Resuming Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume from a power-saving state.
Password
It is recommended that you enable a password on system resume in or­der to protect your data.
Figure 3 - 1
Power Plan
Advanced Settings
(Win 7)

Power Plans

The computer can be configured to conserve power by means of power plans. You
3
can use (or modify) an existing power plan, or create a new one.
3 - 4 Power Plans
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.
Each Windows power plan will also adjust the processor performance of your ma-
Figure 3 - 2
Power Plans
Click to Show/Hide additional power plans
chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) pow­ered. The recommended Balanced power plan will balance power saving and per­formance.
Power Management
3
Power Plans 3 - 5
Power Management

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where
3
you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.
3 - 6 Power-Saving States

Hibernate

Figure 3 - 3
Start Menu Power
Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.
Power Management
3
Power-Saving States 3 - 7
Power Management
Password Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can dis­able this setting from the Power Options menu by clicking Require a
password on wakeup
in the left menu, and se­lecting the options (click
Change settings that are currently unavail­able).
Figure 3 - 4
Power Options
Define Power
Buttons
3

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.
3 - 8 Configuring the Power Buttons

Resuming Operation

Closing the Lid
If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.
Table 3 - 1
Resuming Operation
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).
You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).
Power Status
Power Off Off Press the Power Button
Sleep Blinking Green
Hibernate
Display Turned Off Green Press a Key or Move the Mouse/Touchpad
Icon Color
Off (battery)
Orange (AC/DC adapter)
Power Management
3
To Resume
Press the Power Button
Press the Sleep Button (Fn + F4 Key Combo)
Press the Power Button
Configuring the Power Buttons 3 - 9
Power Management
Power Conservation
Modes
The Energy Star setting will result in maximum power saving, but with the possible loss of some performance.
Setting the mode to Bal- ance will give power saving matched with performance.
Performance will give optimum computer per­formance but with less power conservation.
Figure 3 - 5
Control Center
3

Power Conservation Modes

This system supports Energy Star power management features that place comput­ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center:
1. Press the Fn + Esc key combination to toggle the Control Center on/off.
2. Click either the Performance, Balanced or Energy Star button.
3. Click in a blank area of the icon or press a key on the keyboard to exit Power
Conservation Mode without making any changes.
3 - 10 Configuring the Power Buttons

Battery Information

Low Battery
Warning
When the battery is criti­cally low, immediately connect the AC/DC adapter to the computer or save your work, oth­erwise, the unsaved data will be lost when the power is depleted.
Figure 3 - 6
Battery Icon
(Taskbar) & Battery
Advanced Settings
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure
3 - 1 on page 3 - 4).
Click the battery icon in the taskbar to see the current battery level and charge status.
Power Management
3
Battery Information 3 - 11
Power Management
Windows Mobility
Center
The Windows Mobility Center control panel
provides an easy point of access for information on battery status, power plans used and wireless device status etc.
Figure 3 - 7
Windows Mobility
Center
3

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
Reduce the amount of time before the display is turned off.
Close wireless, Bluetooth, modem or co mmunication applications when they are
not being used.
Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
3 - 12 Battery Information

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason (e.g. long term storage) see “Removing the Battery”
on page 6 - 4.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 15 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 7 for information on the battery charge status, and to “Battery In­formation” on page 3 - 11 for more information on how to maintain and properly
recharge the battery pack.)
Power Management
3
Battery Information 3 - 13
Power Management
Caution
Danger of explosion if battery is incorrectly re­placed.
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s in­structions.
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has bee n d roppe d we do not recommend using it any further, as even if the computer continues to work with a dam­aged battery in place, it may cause circuit damage, which may possibly result in fire . It is recommended that you replace your computer battery every two years.

Proper handling of the Battery Pack

DO NOT disassemble the battery pack under any circumstances
DO NOT expose the battery to fire or high temperatures, it may explode
3
DO NOT connect the metal terminals (+, -) to each other
3 - 14 Battery Information

Battery FAQ

Figure 3 - 8
Power Plan Create
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never.
Power Management
3
Battery Information 3 - 15
Power Management
Figure 3 - 9
Change Plan
Settings / Change
Advanced Power
Settings
3
3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.
3 - 16 Battery Information
4. Scroll down to Battery and click + to expand the ba ttery options.
Figure 3 - 10
Power Options
Advanced Settings -
Battery
5. Choose the options below (click Yes if a warning appears):
Low battery levels = 0%
Critical battery Levels = 1%
Low battery action = Do Nothing
Critical battery action (On battery) = Shut Down
Critical battery action (Plugged in) = Do Nothing
Power Management
3
Battery Information 3 - 17
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
3 - 18 Battery Information
Drivers & Utilities
Driver Installation & Power
When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power source. Some drivers draw a significant am ou n t of power during the installation procedure, and if the remaining battery ca-
pacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the lat­est versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.

What to Install

The Device Driv ers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to install and it is very important that the drivers are installed in the order indicated (all drivers provided are for Windows 7 with Service Pack 1).
The procedures for installing drivers for the PC Camera, Wireless LAN and Bluetooth & WLAN Combo modules are provided in “Modules & Options” on page 7 - 1.
4
What to Install 4 - 1
Drivers & Utilities

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Driv- ers (button) to access the Optional driver menu.
4
Figure 4 - 1 - Drivers Installer Screen 1
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, (you should note down the drivers as you install them).
3. Follow the instructions for each individual driver installation procedure as listed on the following pages.
4 - 2 Driver Installation
Figure 4 - 2 - Drivers Installer Screen 2
Drivers & Utilities
Drivers for Windows 7 with Servic e Pack 1
Chipset Page 4 - 6 PC Camera Module Page 7 - 2 Video (VGA) P age 4 - 6 Wireless LAN Module Page 7 - 10 NVIDIA Video (VGA) Page 4 - 6 I ntel® Wireless Display Application Page 7 - 31 LAN Page 4 - 6 Bluetooth & WLAN Combo Module Page 7 - 36 CardReader Page 4 - 6 THX TruStudio Pro Audio Page 7 - 43
Touchpad Page 4 - 6
Hot Key Page 4 - 7 Intel® Smart Connect Technology Page 7 - 49 USB 3.0 Page 4 - 7 MEI Driver Page 4 - 7 Audio Page 4 - 7
Intel Rapid Storage Technology
(required for hard disks in AHCI mode)
Page 7 - 48
Table 4 - 1 - Driver Installation
Note that for Intel and some 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN & Bluetooth drivers.
Driver Installation 4 - 3
4
Drivers & Utilities
Manual Driver Installation
Click Bro wse CD/DVD (button) in the Drivers Install­er application and browse to the executable file in the
appropriate driver folder.
4
Windows Update
After installing all the drivers make sure you enable Windows Update in order to get all the latest securi ty updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 -
8 for instructions.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro- grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea- tures menu:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Double-click Device Manager (Hardware and Sound > Device Manager).
3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
4 - 4 Driver Installation
Drivers & Utilities
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slight­ly. As a general guide follow the default on screen in­structions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a re­start is required to install the driver.
Make sure any modules (e.g. PC Camera, WLAN or
3.75G/HSPA) are ON before installing the appropriate driver.

User Account Control

If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as direct­ed.

Windows Security Message

If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or “Install” to continue the installation procedure.
You will receive this message in cases where the driv­er has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.

New Hardware Found

If you see the message “New Hardware Found” dur­ing the installation procedure (other than when out- lined in the driver install procedure), click Cancel to close the window, and follow the installation proce­dure.
4
Driver Installation 4 - 5
Drivers & Utilities

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive and click Install Driv-
ers (button).

Chipset

4
1. Click 1.Install Chipset Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer .

Video (VGA)

1. Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer .

NVIDIA Video (VGA)

1. Click 3.Install nVIDIA VGA Driver > Yes.
2. Click AGREE AND CONTINUE (button) to
accept the terms of the license agreement.
3. Click Next > Next.
4. Click the RESTART NOW button to restart
the computer.
Note: After installing the video driver go to the Dis­play/Display Settings control panel to adjust the vid-
eo settings to the highest resolution.
LAN
1. Click 4.Install LAN Driver > Yes.
2. Click Next > Install.
3. Click Finish.

CardReader

1. Click 5.Install Cardreader Driver > Yes.
2. Click Finish.

Touchpad

1. Click 6.Install Touchpad Driver > Yes.
2. Click Next.
3. Click the button to accept the license agreement and click Next.
4. Click Finish > Restart Now to restart the com­puter.
4 - 6 Driver Installation
Drivers & Utilities

Hot Key

1. Click 7.Install Hotkey AP > Yes.
2. Click Next > Next.
3. Click Finish > Finish to restart the computer.

USB 3.0

1. Click 8.Install USB 3.0 Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer .

MEI Driver

1. Click 9.Install MEI Driver > Yes.
2. Click Next > Yes > Next.
3. Click Finish.

Audio

1. Click 10. Install Audio Driver > Yes.
2. Click Next.
3. Click the button to agree to the license and
click Next.
4. Click Next > Next > Next.
5. Click Finish to restart the computer .
Note that after installing the audio driver the system will not return to the Drivers Installer screen. To in- stall any of the optional drivers listed overleaf, eject the Device Drivers & Utilities + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click Option Drivers (button) to ac- cess the optional driver menu.
It is recommended you now also install the Intel Rap- id Storage Technology driver (see “IRST Driver In-
stallation” on page 7 - 48 - required for AHCI mode
hard disks).
4
Driver Installation 4 - 7
Drivers & Utilities
Windows Update
After installing all the drivers make sure you enable Win­dows Update in order to get all the latest security up-
dates etc. (all updates will include the latest hotfixes from Microsoft).
To enable Windows Update make sure you are con- nected to the internet:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Windows Update (System and Security/ Security).
3. Click Check for updates (button).
4. The computer will now check for updates (you need to be connected to the internet).
5. Click Install now (button) to begin checking for the updates.
6. Click Install updates (button) to install the updates.
4

Windows Experience Index

After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi- ence Index (make sure the AC/DC adapter is plugged in):
1. Click Start, and click Control Panel.
2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index).
3. Click “Rate this computer/Refresh Now/Re- run the assessment”.
4. The computer will take a few minutes to assess the system performance.
5. Close the control panel.
4 - 8 Driver Installation
Drivers & Utilities

Optional Drivers

See the pages indicated for the driver installation procedures for any modules included in your purchase option.
Figure 4 - 3 - Drivers Installer - Option Drivers Menu
Note that for Intel and some 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN & Bluetooth drivers.
4
Driver Installation 4 - 9
Drivers & Utilities
4
4-10

Chapter 5: BIOS Utilities

BIOS Screens
Note that the BIOS screens pictured on these pages are intend­ed for guidance in set­ting up your system’s BIOS.
BIOS versions are sub­ject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.

Overview

This chapter gives a brief introduction to the computer’s built-in software:
If your computer has never been set up, or you are making impo rtant changes to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Utilities
5
Overview 5 - 1
BIOS Utilities

The Setup Utility

Each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.
5
If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.
The Aptio Setup Utility tells the syst em how to configure itself and manage basic features and subsystems (e.g. port configuration).
To enter Setup, turn on the computer and press F2 (give the system a few seconds to enter Setup). If the Boot Logo is enabled the F2 on screen will be highlighted to illustrate that the system is processing the request during the POST (or press F7 for boot options). If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.
5 - 2 The Setup Utility
To see the boot options press F7 and choose your preferred boot device.

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and “non­fatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) and you can then press F7 (the F7 on screen will be highlighted to illustrate that the system is processing the request) for boot options.
Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be highlighted to illustrate that the system is processing the request) to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.
BIOS Utilities
5
The Setup Utility 5 - 3
BIOS Utilities
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configura­tion appropriate for your model and options.
Figure 5 - 1
Navigation Menu
5

Setup Screens

The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make chang­es to Setup.
Instructions on how to navigate each screen are in the box at the bottom right side of the screen.
If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
5 - 4 The Setup Utility
The Item Specific Help on the upper right side of each screen explains the highlight­ed item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that sub­ject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.

Main Menu

Figure 5 - 2
Main Menu

System Time & Date (Main Menu)

The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
BIOS Utilities
5
Main Menu 5 - 5
BIOS Utilities

SATA Port # (Main Menu)

Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports.

System/Extended Memory: (Main Menu)

This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
5

MB Series / BIOS Revision / KBC/EC firmware Revision

This item contains information on the BIOS version etc., and is not user configu­rable.
5-6Main Menu

Advanced Menu

Figure 5 - 3
Advanced Menu
BIOS Utilities

Advanced Chipset Control (Advanced Menu)

The sub-menu here allows you to adjust the Bluetooth Power Setting.
5
Advanced Menu 5 - 7
BIOS Utilities
SATA Mode
Selection
If you have installed the Windows 7 operating system with either IDE
or AHCI mode enabled, DO NOT disable the set
mode (if you wish to dis­able the set mode you will need to reinstall the Windows 7 OS).

Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)

You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is started up or restarted. Enabling the power setting will have the module retain the last power status (on or off) before any restart or shut down.
5
5 - 8 Advanced Menu

Intel Smart Connect Technology (Advanced Menu)

Smart Connect is a technology that makes checks on web applications that are open even when the computer is in sleep mode, and thus allows updates to be made with­out the need to turn the computer on.

Intel Anti-Theft Technology (Advanced Menu)

Anti-Theft Technology, which is built-in to the processor of the computer, allows system administrators to render your computer useless to thieves by sending a poi­son pill encrypted SMS message over a 3G network etc. Administrators can also re­motely unlock a recovered computer quickly, or direct the system to send location information (GPS coordinates) back to a central server.

SATA Mode Selection (Advanced Menu)

You can configure SATA (Serial ATA) control to operate in IDE (native/compati­ble), AHCI (Advanced Host Controller Interface) modes from this menu. The SATA Mode should be set BEFORE installing an operating system, and after you have backed up all necessary files and data (see sidebar).

Boot Logo (Advanced Menu)

Use this menu item to enable/disable th e Boot Logo screen at system startup. If you disable the Boot Logo you will not see the F2 Enter Setup or F7 Boot Options prompts on the screen, however you can still press these keys, while the boot screen is displayed, to perform the Enter Setup or Boot Option functions.

Power On Boot Beep (Advanced Menu)

Use this menu item to enable/disable the beep as the computer starts up.

Battery Low Alarm Beep (Advanced Menu)

Use this menu item to enable/disable the battery low alarm beep.
BIOS Utilities
5
Advanced Menu 5 - 9
BIOS Utilities

Security Menu

The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.
Figure 5 - 4
Security Menu
5
Security Menu

Set Supervisor Password (Security Menu)

You can set a password for access to the Aptio Setup Utility. This will not affect access to the computer OS (only the Aptio Setup Utility). If you set a supervisor password you can then add a user password and password on boot.
5 - 10 Security Menu

Set User Password (Security Menu)

Password Warning
If you set a boot pass­word (Password on boot is “Enabled“), NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your ven­dor and you may lose all of the information on your hard disk.
You can set a password for user mode access to the Aptio Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Aptio Setup Utility cannot be modified in user mode. You can only set the user password after you have set the supervisor password.
BIOS Utilities

Password on boot (Security Menu)

Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled). If “Enabled is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.
5
Security Menu 5 - 11
BIOS Utilities
Figure 5 - 5

Boot Menu

BIOS Screens
Note that the BIOS screens pictured on these pages are intend­ed for guidance in set­ting up your system’s BIOS.
BIOS versions are sub­ject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.
5
5 - 12 Boot Menu
Boot Menu
When you turn the computer on it will look for an operating system (e.g. Windows
7) from the devices listed in this menu, and in this priority order. If it cannot find
the operating system on that device, it will try to load it from the next device in the order specified in the Boot Option Priorities. Item specific help on the right is available to help you move devices up and down the order.

Boot Sequence (Boot Menu)

Use the arrow keys to move up and down the menu, and go to either Network De­vice BBS Priorities or Hard Drive BBS Priorities and use the
move the device’s boot priority up and down the list (the selected device will be highlighted in white).
+ and - keys to
BIOS Utilities
5
Boot Menu 5 - 13
BIOS Utilities
Figure 5 - 6

Exit Menu

5
5 - 14 Exit Menu
Exit Menu
Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made
to the Setup. You can also choose Load Setup Defaults to restore the original Setup defaults and return the Setup to its original state, and erase any previous changes you have made in a previous session.
Loading...