Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
ErP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode:
•Off Mode < 0.5W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Re orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the service representative or an experienc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1.This device may not cause interference.
And
2.This device must accept any interference, including interfer ence that may cause undesired operation of the
device.
IV
FCC RF Radiation Exposure Statement:
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Preface
V
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1.Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2.Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3.Do not use the telephone to report a gas leak in the vicinity of the leak.
4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5.This product is intended to be supplied by a Listed Power Unit as follows:
•AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19.5V, 11.8A (
OR
•AC Input of 100 - 240V, 50 - 60Hz, DC Output of 19V, 10.5A (
VI
230
Watts) minimum AC/DC Adapter.
200
Watts) minimum AC/DC Adapter.
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2.Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
VII
Preface
3.Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4.Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5.Take care when using peripheral devices.
Use only approved brands of
peripherals.
VIII
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
Servicing
Bottom Cover Removal Warning
Users should not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of
your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your distributor/supplier for further information.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before restoring power to the system.
Also note the following when the cover is removed:
•Hazardous moving parts.
•Keep away from moving fan blades.
Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from
the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
•When the power cord or AC/DC adapter is damaged or frayed.
•If the computer has been exposed to rain or other liquids.
•If the computer does not work normally when you follow the operating instructions.
•If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•If there is an unusual odor, heat or smoke coming from your computer.
Preface
IX
Preface
Power Safety Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals and
cables (including telephone lines and power
cord).
You must also remove
your battery in order to
prevent accidentally
turning the machine on.
Before removing the
battery disconnect the
AC/DC adapter from
the computer.
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the powe r cord, be sure t o disconnect it by the plug head, not
by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
X
Preface
Polymer/Lithium-Ion Battery Precautions
Note the following information which is specific to Polymer/Lithium-Ion batteries only, and where applicable,
this overrides the general battery precaution information overleaf.
•Polymer/Lithium-Ion batteries may experience a slight expansion or swelling, however this is part of the battery’s
safety mechanism and is not a cause for concern.
•Use proper handling procedures when using Polymer/Lithium-Ion batteries. Do not use Polymer/Lithium-Ion batteries
in high ambient temperature environments, and do not store unused batteries for extended periods.
•If you are working in areas of low temperature use the AC/DC adapter to power the computer.
See also the general battery precautionary information overleaf for further information.
XI
Preface
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
General Battery Precautions
•Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
•Do not remove any batteries from the computer while it is powered on.
•Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
•If you do not use the battery for an extended period, then remove the battery from the computer for storage.
•Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
•Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.
•Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
•Keep the battery away from metal appliances.
•Affix tape to the battery contacts before disposing of the battery.
•Do not touch the battery contacts with your hands or metal objects.
XII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Cleaning Instructions
(For Computer Models Supplied with Light Blue Cleaning Cloth)
Some computer models in this series come supplied with a light blue cleaning cloth. To clean the computer case
with this cloth follow the instructions below:
1.Power off the computer and peripherals.
2.Disconnect the AC/DC adapter from the computer.
3.Use a little water to dampen the cloth slightly.
4.Clean the computer case with the cloth.
5.Dry the computer with a dry cloth, or allow it time to dry before turning on.
6.Reconnect the AC/DC adapter and turn the computer on.
XIII
Preface
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
Travel Considerations
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.Check that the battery pack and any spares are fully charged.
2.Power off the computer and peripherals.
3.Close the display panel and make sure it’s latched.
4.Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5.The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6.Put the notebook in its carrying bag and secure it with the bag’s straps.
7.If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8.Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your “papers” are handy.
XIV
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XV
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
•Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
•Your knees should be slightly higher than your hips. Place your feet flat on the flo or or on
a footrest if necessary.
•Use a chair with a back and adjust it to support your lower back comfortably.
•Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
•Take periodic breaks if you are using the computer for long periods of time.
Remember to:
•Alter your posture frequently.
•Stretch and exercise your body several times a day.
•Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XVI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
•Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
•Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
•Position the display directly in front of you at a comfortable viewing distance.
•Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
•Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
•Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
•Rotate desktop background images every few days.
•Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp
edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated
logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during
transport. If any such wear and tear develops contact your distributor/supplier.
Power Safety ................................................................................................................................................X
Not Included ..............................................................................................................................................1-3
System Software ........................................................................................................................................1-4
System Startup ...........................................................................................................................................1-5
LCD Panel Open ........................................................................................................................................1-6
LED Indicators ...........................................................................................................................................1-7
Illuminated White LED Keyboard .............................................................................................................1-8
Illuminated Color LED Keyboard .............................................................................................................1-9
Control Center .........................................................................................................................................1-11
Keyboard Backlight LED ........................................................................................................................1-12
Function Keys & Visual Indicators .........................................................................................................1-20
Front & Right Views ...............................................................................................................................1-21
Rear & Left Views ...................................................................................................................................1-22
Windows 10 Taskbar ...............................................................................................................................1-31
Action Center ...........................................................................................................................................1-32
Video Features .........................................................................................................................................1-33
XX
Preface
Microsoft Hybrid Graphics Or Discrete Graphics Mode ........................................................................1-34
Power Options .........................................................................................................................................1-38
Audio Features ...........................................................................................................................................2-4
Setup for 5.1 Surround Sound ...................................................................................................................2-5
Setup for Audio Recording ........................................................................................................................2-7
Setup for Audio Devices - 2-In-1 Audio Jack ...........................................................................................2-8
Touchpad and Buttons/Mouse ...................................................................................................................2-9
The Power Sources ....................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-4
Shutting the Computer Down ....................................................................................................................3-5
Power Plans ...............................................................................................................................................3-6
XXI
Preface
Power-Saving States ..................................................................................................................................3-8
Shut down ..................................................................................................................................................3-9
Configuring the Power Buttons ...............................................................................................................3-10
Power Conservation Modes .....................................................................................................................3-13
Settings Menu Power Controls ................................................................................................................3-15
Battery Information .................................................................................................................................3-18
Battery Power ..........................................................................................................................................3-18
Conserving Battery Power .......................................................................................................................3-19
Battery Life ..............................................................................................................................................3-20
New Battery .............................................................................................................................................3-20
Recharging the Battery with the AC/DC Adapter ...................................................................................3-20
Proper handling of the Battery Pack ........................................................................................................3-21
What to Install ............................................................................................................................................4-1
User Account Control ................................................................................................................................4-6
Windows Security Message .......................................................................................................................4-6
New Hardware Found ................................................................................................................................4-6
Video (VGA) .............................................................................................................................................4-7
NVIDIA Video (VGA) ..............................................................................................................................4-7
LAN ...........................................................................................................................................................4-8
Control Center ...........................................................................................................................................4-8
MEI Driver .................................................................................................................................................4-8
The Power-On Self Test (POST) ...............................................................................................................5-2
Failing the POST .......................................................................................................................................5-3
The Setup Utility ........................................................................................................................................5-4
Main Menu .................................................................................................................................................5-6
SATA Port # (Main Menu) ........................................................................................................................5-6
Mac Address (Main Menu) ........................................................................................................................5-7
Advanced Menu .........................................................................................................................................5-8
Advanced Chipset Control (Advanced Menu) ..........................................................................................5-8
FlexiCharger (Advanced Menu > Advanced Chipset Control) .................................................................5-9
MSHybrid or DISCRETE Switch (Advanced Menu > Advanced Chipset Control) ...............................5-10
GPU Performance Scaling (Advanced Menu > Advanced Chipset Control) ..........................................5-10
VT-d (Advanced Menu > Advanced Chipset Control) ............................................................................5-10
Fast Boot (Advanced Menu > Advanced Chipset Control) .....................................................................5-11
DDI Control (Advanced Menu > Advanced Chipset Control) ................................................................5-11
Intel(R) Thunderbolt Technology
(Advanced Menu > Intel(R) Thunderbolt) ..............................................................................................5-12
Security Level (Advanced Menu > Intel(R) Thunderbolt) ......................................................................5-13
Overclocking Performance Menu (Advanced Menu) ..............................................................................5-14
XXIV
Preface
SATA Mode (Advanced Menu) ..............................................................................................................5-15
Boot Logo (Advanced Menu) ..................................................................................................................5-16
Power On Boot Beep (Advanced Menu) .................................................................................................5-16
Security Menu ..........................................................................................................................................5-17
Set Supervisor Password (Security Menu) ..............................................................................................5-17
Set User Password (Security Menu) ........................................................................................................5-18
Password on boot: (Security Menu) ........................................................................................................5-18
Secure Boot Control (Security Menu) .....................................................................................................5-19
Boot Menu ...............................................................................................................................................5-21
Exit Menu ................................................................................................................................................5-23
PC Camera Module ..................................................................................................................................6-69
Camera App .............................................................................................................................................6-70
Taking Pictures/Capturing Video ............................................................................................................6-73
Basic Hints and Tips ..................................................................................................................................7-2
XXVII
Preface
Backup and General Maintenance .............................................................................................................7-3
Ports and Jacks ..........................................................................................................................................A-2
2-in-1 Audio Jack (Line-Out & S/PDIF-Out Jack) ...................................................................................A-2
DC-In Jack ................................................................................................................................................A-2
HDMI-Out Port .........................................................................................................................................A-2
Headphone-Out Jack .................................................................................................................................A-2
Microphone-In Jack ..................................................................................................................................A-3
Mini DisplayPorts 1.3 ...............................................................................................................................A-3
RJ-45 LAN Jack .......................................................................................................................................A-3
Control Center ..........................................................................................................................................B-1
Power Modes ............................................................................................................................................B-3
Control Center Menus ...............................................................................................................................B-4
Power Status (System Program) .............................................................................................................B-5
Display Utility (System Program for High Definition displays only) ......................................................B-9
CPU / Memory Overclocking Support ...................................................................................................B-12
CPU Overclocking ..................................................................................................................................B-14
Language Interface .................................................................................................................................B-25
Microsoft Hybrid Graphics Or Discrete Graphics Mode .........................................................................C-2
Microsoft Hybrid Graphics .......................................................................................................................C-3
Video Driver Installation ..........................................................................................................................C-5
Video (VGA) ............................................................................................................................................C-5
NVIDIA Video (VGA) .............................................................................................................................C-5
Configuring an External Display (NVIDIA) ..........................................................................................C-28
HDCP Status ...........................................................................................................................................C-32
Adjust Video Settings .............................................................................................................................C-33
Set Digital Audio ....................................................................................................................................C-35
Intel® HD Graphics Control Panel .........................................................................................................C-36
Communication .........................................................................................................................................D-3
XXXII
Preface
Power & Battery .......................................................................................................................................D-3
Power Management ..................................................................................................................................D-4
Features .....................................................................................................................................................D-4
Operating System ......................................................................................................................................D-4
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2A guide to using some of the main features of the computer e.g. the storage devices (hard disk and
card reader), TouchPad & Mouse and Audio Features.
• Chapter 3 The computer’s power management options.
• Chapter 4The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 A quick guide to the computer’s PC Camera, Wireless LAN, Fingerprint, Bluetooth & WLAN Combo, Sound Blaster Audio and Intel modules (some of which may be optional depending on
your purchase configuration).
• Chapter 7 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the Control Center . and Flexikey® Application.
• Appendix C Information on the Video driver controls.
• Appendix D The computer’s specification.
1
Overview 1 - 1
1
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the User’s Manual. You
may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4
- 4. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers
& Utilities” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Not Included
Operating Systems (e.g. Windows 10) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
1
Overview 1 - 3
1
Windows OS
Note that the information included on the following pages is for Windows 10 only.
In order to run Windows 10 (64-bit) your computer requires a minimum 8GB of system memory (RAM).
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the Windows 10 (64-bit) operating system
is supported.
Design Styles
This notebook series includes two different design styles. Note that your model may appear slightly different from
those pictured in this manual. Note that this computer model series may support a range of CPUs and/or video adapters.
1 - 4 Overview
Quick Start Guide
135°
Shutdown
Note that you should always
shut your computer down by
choosing the Shut Down command in Windows (see page
1 - 38). This will help prevent
hard disk or system problems.
System Startup
1. Remove all packing materials, and place the computer on a stable surface, and securely attach any peripherals you want to
use with the notebook (e.g. keyboard and mouse) to their ports.
2. When first setting up the computer use the following procedure (as to safeguard the computer during shipping, the
battery will be locked to not power the system until first connected to the AC/DC adapter and initially set up as below):
• Attach the AC/DC adapter cord to the DC-In jack on the left of the computer, then plug the AC power cord into an outlet, and connect
the AC power cord to the AC/DC adapter and leave it there for 6 seconds or longer.
• Remove the adapter cord from the computer’s DC-In jack, and then plug it back in again; the battery will now be unlocked.
3. Use one hand to raise the
hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).
4. Press the power button icon (make sure to presss the icon directly and not either side of the icon) on the top of the
computer for about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).
lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);
use the other
1
Figure 1 - 1 - Opening the Lid/LCD
System Startup 1 - 5
1
Figure 1 - 2
LCD Panel Open
1. Built-In PC Camera
2. PC Camera LED
3. Built-In Array
Microphone
4. LCD
5. Speakers
6. Power Button
7. Illuminated LED
Keyboard (White or
Colored)
8. TouchPad & Buttons
9. Fingerprint Reader
Sensor (Optional)
8
Note that the Touchpad/
Clickpad and Buttons has a
valid operational area indicated within the dotted lines
above.
4
1
5
8
6
7
2
5
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
(e.g. WLAN or Bluetooth
aboard aircraft is usually prohibited. Make sure any wireless modules are OFF (i.e. the
system is in Airplane Mode) if
you are using the computer
aboard aircraft.
Use Fn + F11 Airplane Mode
key combination to toggle Airplane Mode On/Off, and check
the LED indicator for the power
status.
3
9
Quick Start Guide
LCD Panel Open
1 - 6 LCD Panel Open
Quick Start Guide
LED Indicators
The LED indicators display helpful information about the current status of the computer.
IconColor DescriptionIconColorDescription
1
Green
Green
Green
GreenHard Disk ActivityOrangeAC/DC Power is Plugged In
Green
GreenDiscrete ModeBlinking GreenThe Computer is in Sleep Mode
Airplane Mode is ON (the WLAN & Bluetooth
OffMSHYBRID ModeGreenThe Computer is On
Number Lock is Activated
Caps Lock is Activa ted
Scroll Lock is Activated
Modules are OFF)
OrangeThe Battery is Charging
Blinking Orange
GreenThe Battery is Fully Charged
Blinking Orange*
The Battery has Reached Critically Low
Power Status
The Powered USB Port is On
(see
“Powered USB 3.0 Port” on page 1 - 21
Table 1 - 1 - LED Indicators
LCD Panel Open 1 - 7
)
1
Other Keyboards
If your keyboard is damaged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it automatically. However special functions/hot-keys
unique to the system’s
regular keyboard may not
work.
Scr Lk
Hold down the Fn Key
and Scr Lk to enable
scroll lock and check the
LED indicator for status.
Numerical
Play/Pause Key
Function Keys
ScrLk &
NumLk Keys
Fn Key
Keypad
Windows Logo Key
Menu/Application Key
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.
Quick Start Guide
Illuminated White LED Keyboard
The illuminated white LED keyboard has an embedded numerical keypad for easy
numeric data input, and features function keys to allow you to change operational
features instantly. See Table 1 - 5, on page 1 - 20 for full function key combination
details.
1 - 8 Illuminated White LED Keyboard
Figure 1 - 3 - Illuminated White LED Keyboard
Illuminated Color LED Keyboard
Other Keyboards
If your keyboard is damaged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it automatically. However special functions/hot-keys
unique to the system’s
regular keyboard may not
work.
Scr Lk
Hold down the Fn Key
and Scr Lk to enable
scroll lock and check the
LED indicator for status.
Numerical
Play/Pause Key
Function Keys
Scr Lk Key
Fn Key
Game Control Keys
Num Lk Key
Windows Logo Key
Menu/Application Key
Numerical
Keypad
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.
The illuminated colored keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 5, on page 1 - 20 for full function key combination
details. and see “Keyboard Backlight LED” on page 1 - 12.
Figure 1 - 4 - Illuminated Color LED Keyboard
Illuminated Color LED Keyboard 1 - 9
Quick Start Guide
1
1
Windows Logo
Keyboard Shortcut
Use the Windows logo
key + D key com-bination to switch between the Start screen
and Windows Desktop.
Menu/Application
Keyboard Shortcut
When the Desktop app
is running you can use
the Menu/Application
key on the keyboard to display the
context menu as per a
mouse right-click.
Quick Start Guide
Keyboard Shortcuts
The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in
Windows 10
.
Windows Logo
Tap WinkeyToggle the Start menu
+ Number (1, 2, etc)Launch an application from the taskbar (numbered from left to right)
1 - 10 Illuminated Color LED Keyboard
Key +
AOpen the Action Center
BSelect the Taskbar Notification Area
C Launch Cortana (in listening mode)
DToggle the Desktop
ELaunch File Explorer (Quick Access tab)
Table 1 - 2 - Keyboard Shortcuts
Description
Quick Start Guide
Control Center Access
To run the
Control Center press the
Fn + Esc key
combination,
or doubleclick the icon
in the notification area
of the taskbar.
Close the Control Center by clicking
the close icon in the top right of the
panel (move the cursor onto the top
right corner of the panel to highlight it).
Control Center
When in the Windows Desktop application (not in the Start screen)press the Fn + Esc key combination, or
double-click the icon
trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch
Pad on/off (see Appendix B for full details).
in the notification area of the taskbar to toggle the Control Center on/off. The Con-
Figure 1 - 5 - Control Center
Control Center 1 - 11
1
1
211
23
4
1
234
5
5
67
6
7
Quick Start Guide
Keyboard Backlight LED
(For Illuminated Colored Keyboards Only)
Press Fn plus the key to toggle the keyboard LED on/off. The keyboard LED may be configured using
the Fn + key combination outlined in the table below. In addition press Fn plus the
keyboard backlight application to configure the settings (see overleaf).
Main Keyboard Colored LED Function key Combinations
The Keyboard Backlight application can be accessed by pressing the Fn plus key (or by clicking the
Flexikey button in the Gaming section of the Control Center, and then clicking the Backlight tab).
1
Figure 1 - 6 - Keyboard Backlight Application
Keyboard Backlight LED 1 - 13
1
Full Color Swatch256 Color Scheme Swatch
Quick Start Guide
Brightness
Click on any of the numbers (0 - 3) on the brightness bar to set the brightness level of the keyboard backlight.
Color Swatch
The color swatch in the top right of the screen allows you to select a range of colors for your keyboard backligh t
by clicking on the color required. You can choose to display the swatch either in Full Color or as a 256 ColorScheme. Click the Custom mode button to select any colors from the swatch and to apply your chosen colors
to parts of the keyboard (and Top Case Logo LED if applicable).
Figure 1 - 7 - Keyboard Backlight Color Swatches
1 - 14 Keyboard Backlight LED
Quick Start Guide
Illumination Keys
Note that the keyboard illumination (increase/decrease)
keys may be used to configure the keyboard LED in Cus-
tom Mode only.
Modes
The buttons surrounding the swatch allow you to alter the effects of the keyboard backligh t. Click on any of the
buttons to view the effects on the keyboard. Click Save when exiting the application to retain the setting.
Mode Buttons
1
Custom - Display & Configure
Keyboard Sections & Colors
Random Color
Breathe (All Colors)
Cycle Colors
Wave Up/Down
Dancing Effect
Tempo Beat
Flashing
Table 1 - 4 - Mode Buttons
Keyboard Backlight LED 1 - 15
1
Quick Start Guide
Preview
The bottom left section of the application allows you to preview setting changes made to colors on the keyboard.
Keyboard LED Sections
The bottom right section of the application allows you to select partial areas, or all, of the keyboard on which to
apply the color changes and effects.
Figure 1 - 8 - Preview & Keyboard LED Sections
1 - 16 Keyboard Backlight LED
Quick Start Guide
Sets
The application allows you to save up to 3 sets of color and effect combinations. Click Save when exiting the
application to retain the settings.
Figure 1 - 9 - Sets
Save & Exit
Click Exit to quit the application without saving, or Save to exit and retain the settings.
Figure 1 - 10 - Save & Exit
1
Keyboard Backlight LED 1 - 17
1
Flexikey® Enabled
Flexikey® Disabled
Quick Start Guide
Flexikey® Application
The Flexikey® application is a quick hotkey configuration application, which allows you to assign a single key
to launch multiple key combinations, or to launch programs and applications, to create text macros and to
disable certain keys. The application can also be used to configure the mouse buttons to create hotkeys for
gaming etc. All the configuration settings are retained under (up to12) profiles to which the settings are applied.
Click Flexikey® in the Gaming section of the Control Center, or the click the icon in the notification
area of the taskbar, to launch the application (see Appendix B for full details).
1 - 18 Flexikey® Application
Figure 1 - 11 - Flexikey® Hotkey Application
Quick Start Guide
Flexikey® Application Features:
For full details see “Flexikey® Application” on page B - 24.
•EXPRESS KEY - This feature allows you to configure a single key (or mouse click) to send multiple key
combinations, or to create more useful shortcut keys This is useful in gaming or when using applications
which have a complex set of keyboard shortcuts.
•LAUNCH APP - This simply assigns single keys (or mouse clicks) to launch any program’s or application’s
executable file.
•EXPRESS TEXT - With this you can assign single keys (or mouse clicks) to send commonly used strings
of text.
•DISABLE - Use this function to disable any keyboard keys or mouse buttons.
•STATISTICS - Use this to quickly record keys in use in any application, and to disable unused keys.
1
Flexikey® Application 1 - 19
1
Quick Start Guide
Function Keys & Visual Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.
Fn + Power ButtonPowered USB 3.0 Port Power ToggleFn + BackspaceFlexikey® Enable/Disable
Play/Pause (in Audio/Video Programs)
Touchpad Toggle
Mute Toggle
Backlight Keyboard
Toggle Off/High/Low
(White Illuminated
KeyboardsDesigns
Volume Decrease/Increase
Table 1 - 5 - Function Keys & Visual Indicators
*Note: It is recommended that you use Maximum fan speed when playing games (use Fn + 1).
1 - 20 Flexikey® Application
Front & Right Views
Figure 1 - 12
Front & Right Views
1. LED Power Indicators
2. Headphone Jack
3. Microphone Jack
4. 2-In-Audio Jack
(Line-Out /
S/PDIF-Out Jack)
5. Multi-in-1 Card
Reader
6. USB 3.0 Port (USB
3.1 Gen 1 - Type A)
7. 1 * Powered USB 3.0
Port (USB 3.1 Gen 1)
8. RJ-45 LAN Jack
9. Vent/Fan Intake
10. Security Lock Slot
L
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/
fan intake(s) while the computer is in use.
1
5
29348
67
10
Multi-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC up to UHS-II
Powered USB 3.0 Port
Note that the USB 3.0 port is not operational under DOS and does not support wake on
USB. The powered USB 3.0 ( in Figure 1 - 12 on page 1 - 21) port can supply power
(for charging devices only, not for operating device s) when the system is off but still
powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with
a capacity level above 20% (this may not work with certain devices - see page 7 - 11). Toggle power to this port by using Fn + power button.
7
Quick Start Guide
Front & Right Views 1 - 21
1
1
Figure 1 - 13
Rear & Left Views
1. V ent/Fan Intake
2. DC-In Jack
3. HDMI-Out Port
4. Mini DisplayPort(1.3) #1
5. Mini DisplayPort(1.3) #2
6. 1 * USB 3.1 Gen 1
(Type C) Port OR 1 *
Thunderbolt™ 3
Combo Port USB 3.1
Gen 2 (Type C)
(Factory Option - See
over)
7. 2 * USB 3.0 Ports
(USB 3.1 Gen 1 Type A)
1
2
4
HDMI Port / Mini Display Port 1.3
Note that the HDMI Port and Mini Display ports support video and audio signals to attached external
displays (see “HDMI Audio Configuration” on page C - 9).
3
1
6
7
1
5
7
Thunderbolt™ Port Set for Display
If your purchase configuration includes the Thunderbolt™ combo port then the display configuration for the Thunderbolt™ port and Mini Display Port can be set up in the BIOS (see “DDI Control (Advanced Menu > Advanced Chipset
Control)” on page 5 - 11).
If the Thunderbolt™ port is enabled for display then the Mini Display Port #1 will be turned off.
4
Quick Start Guide
Rear & Left Views
1 - 22 Rear & Left Views
Quick Start Guide
Thunderbolt Port Devices
If your purchase option includes a Thunderbolt port note the following:
When plugging a device into a Thunderbolt port allow 30 seconds for the system to scan and re cognize the connected
device.
Ejecting Thunderbolt Devices
In order to prevent system problems make sure you do not simply pull the cable ou t from th e Thu nder bo lt po rt. Th e
hardware must be ejected safely:
1.Go to the notification area of the taskbar in the Desktop App and click on the Safely Remove Hardware and Eject Media icon.
2.Click on Eject “Thunderbolt Device Name”.
3.When you see the “Safe to Remove Hardware” message you can remove the cable after about 20 seconds, to
make sure that it is safe to eject the device.
Thunderbolt Port Security Level
The security level (including setting the port for display devices) for the Thunderbolt port can be set up in the BIOS (see
“Security Level (Advanced Menu > Intel(R) Thunderbolt)” on pa ge 5 - 13).
1
Rear & Left Views 1 - 23
1
Figure 1 - 14
Bottom View
1. Fan Outlet/Intake
2. Subwoofer Speaker
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/
fan intake(s) while the computer is in use.
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/
optical device etc., for any
reason, please contact your
distributor/supplier for further information.
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 18 for full instructions.
1
1
1
1
2
1
Quick Start Guide
Bottom View
1 - 24 Bottom View
Quick Start Guide
Desktop
Windows Screens
Note that the Windows screens on the
following pages are
included as a basic
guide and introduction to navigating
around Windows 10.
However note that
these screens are always subject to
change, upgrade and
redesign. Check the
Microsoft website for
details.
Windows 10 Start Menu
Most of the apps, control panels, utilities and programs within Windows 10 can be accessed from the Start
Menu by clicking the icon in the taskbar in the lower left corner of the screen (or by pressing the Windows
Logo Key on the keyboard).
Figure 1 - 15 - Windows Start Menu
Windows 10 Start Menu 1 - 25
1
1
Right-Click Icon
Quick Start Guide
Right-Clicking the Windows Logo In Start Menu
Right-click the Start Menu icon (or use the Windows Logo Key + X key combination) to bring up an
advanced Context Menu of useful features such as Apps and Features, Power Options, Task Manager, Search,
File Explorer, Device Manager, Computer Management and Network Connections etc.
Figure 1 - 16 - Right-Click Windows Logo in Start Menu
1 - 26 Windows 10 Start Menu
Quick Start Guide
Start Menu Apps & Tiles
The Windows 10 Start Menu will contain a number of apps, and many more will be installed as you add more
applications etc. Not all of these apps can fit on the screen so may need click and drag the handles at the edge of
the screen to expand the menu in order to view all the apps (you can use the scroll bar to mov e up and down the
screen).
1
Figure 1 - 17 - Expanding the Start Menu
Windows 10 Start Menu 1 - 27
1
Quick Start Guide
Pining/Unpinning Apps & Programs to/from the Start Menu
To make things easy to find you can add and remove tiles for apps and programs to the Start Menu. Right-Click
on a program’s icon and select Pin to Start from the drop-down menu. To remove an app or program from the
Start Menu right-click the icon and select Unpin from Start. You can use the same method to pin apps/pro-grams to/from the taskbar (select pin to taskbar/unpin this program from the taskbar).
Figure 1 - 18 - Pin to Start/Unpin from Start
1 - 28 Windows 10 Start Menu
Windows 10 Control Panel
• Select Control Panel
under the Windows
System item in the
Start Menu.
• Type Control Panel
into the Search box in
the taskbar and click on
the icon when it pops
up.
•You can pin the Con-trol Panel tile to Start
or taskbar.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel can be accessed in a number of ways in Windows 10.
Quick Start Guide
1
Figure 1 - 19 - Windows 10 Control Panel Access
Windows 10 Control Panel 1 - 29
1
Quick Start Guide
Settings
The Settings item in the Start Menu (and also as an App) gives you quick access to a number of system settings
control panels allowing you to adjust settings for System, Devices, Network & internet, Personalization, Apps,
Accounts, Time & language, Gaming, Ease of Access, Privacy and Update & security.
Figure 1 - 20 - Settings
1 - 30 Windows 10 Control Panel
Quick Start Guide
Taskbar
Taskbar - Pinned Programs and Apps
Notification Area
Windows 10 Taskbar
In many instances throughout this manual you will see an instruction to access the notification area of the taskbar. The notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and appli-
cations referred to throughout the course of this manual can be accessed from here.
Figure 1 - 21 - Taskbar
You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Pining/
Unpinning Apps & Programs to/from the Start Menu” on page 1 - 28).
1
Windows 10 Control Panel 1 - 31
1
Quick Start Guide
Action Center
The Action Center appears as a vertical panel on the right side of the screen when you swipe in from the right
or click the button in the notification tray. This gives you access to commonly needed functions like Network,
All Settings, Airplane Mode, and Project etc.
1 - 32 Windows 10 Control Panel
Figure 1 - 22 - Action Center
Video Features
1.Attach your display to the
appropriate port, and turn it
on.
2.Press the + P (or Fn +F7) key combination.
3.Click on any one of the
options from the menu to
select PC screen only,
Duplicate, Extend or
Second screen only.
4.You can also click Connect
to a wireless display at the
bottom of the Project screen
and follow the steps to
connect to any wireless
enabled display.
Configuring External Displays
When a single external display is attached to
the HDMI or Display Ports, use the System >
Display (in Settings - page C - 8) control panel
or the + P (or Fn + F7 - page C - 7) key
combination, to configure the external display.
When multiple external displays are attached
you should use the NVIDIA (page C - 28) control panel to configure the external displays.
You cannot configure external displays using the Intel(R) HD Graphics control panel.
You can switch display devices, and configure display options, from the Display settings ( click the Start Menu
and click Settings > System or right-click the desktop and select Display settings) control panel (see page 1 -
35). In Windows 10 it is possible to quickly configure external displays from the Project menu (
dows logo key on your keyboard and theP key or Fn + F7).
To Configure Displays using Project
Figure 1 - 23 - Project (Devices)
Quick Start Guide
press the Win-
Video Features 1 - 33
1
1
Quick Start Guide
Microsoft Hybrid Graphics Or Discrete Graphics Mode
Your computer features a dedicated Discrete Graphics Mode, and a Microsoft Hybrid Graphics Mode featuring switchable graphics technology.
Microsoft Hybrid Graphics Mode - This seamless technology is designed to get best performance from the
graphics system while allowing longer battery life, without having to manually change settings. The computer ’s
operating system (and some applications) will automatically switch between the integrated GPU and the discrete GPU when required by the applications in use. This switch is seamless to the user (see Appendix C).
MSHybrid mode is selected by default. To configure displays in Hybrid mode use the Intel HD Graphics Con-
trol Panel (see page C - 36).
Discrete Graphics Mode - Discrete Graphics Mode will use the dedicated Graphics Processing Unit (GPU)
which is more powerful, and therefore more suitable for playing games, watching HD video or running GPUbased applications. To configure displays in Discrete mode use the NVIDIA Control Panel (see page C - 5).
You can choose either Discrete Mode or MSHybrid mode by selecting the appropriate option from GPU
Switch in the Control Center, or in the BIOS (see page B - 8 or page 5 - 9). You will need to restart the system
after making changes to the selected graphics mode.
1 - 34 Video Features
Quick Start Guide
To access the Display Settings:
1.You can quickly adjust the display by right-clicking the desktop and selecting Display Settings.
2.Adjust the settings for Brightness and color, Scale and layout, Resolution and Orientation from the menus.
3.When and external display is attached you can arrange the display configuration from the Multiple Displays
menu, and arrange the configuration fr om Select and rearrange displays.
4.Click Apply to save any changes made.
1
Figure 1 - 24 - Display Settings
Video Features 1 - 35
1
Quick Start Guide
To access the Intel(R) HD Graphics Control Panel:
1. Right-click the desktop and select Intel(R) Graphics Settings from the menu.
OR
2. Click the icon in the notification area of the Desktop taskbar and select Intel(R) Graphics Settings from the menu.
1 - 36 Video Features
Figure 1 - 25 - Intel® HD Graphics Control Panel
To access the NVIDIA Control Panel:
1
2
1
2
1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 26).
OR
2. Double-click the icon (Figure 1 - 26) in the Windows control panel.
3. To configure displays in Discrete mode use the NVIDIA Control Panel (see page C - 16).
Quick Start Guide
1
Figure 1 - 26 - NVIDIA Control Panel
Video Features 1 - 37
1
Using the Power Button
1. Go to the Start Menu.
2. Click the Power button .
3. Select the power state required fro m
the menu.
Quick Start Guide
Power Options
Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power button item in
Start Menu (or the context menu) may be used to Shut down or Restart (you can also add Hibernate/Sleep tothe menu - see page 1 - 39). To fully control all the power options (including Hibernate mode) go to the Power
Options control panel and configure the power button, sleep button and lid to perform the function selected.
1 - 38 Power Options
Figure 1 - 27 - Shut Down/Restart
Quick Start Guide
Adding Hibernate/Sleep to the Power Men
1. Go to the Power Options (Hardware and Sound) control
panel (or go to Windows Settings > Power & sleep > Additional power settings).
2. Click Choose what the power buttons do.
3. Click “Change settings that are currently unavailable”
.
4. Click to put a check in the Hibernate/Sleep box under
Shutdown settings.
5. Click Save Changes and close the control panel.
You can also use the context menu (right-click the Start Menu icon or press the Windows logo + X key
combination) to Sign out, Sleep, Hibernate, Shut down, and Restart.
Figure 1 - 28 - Context Menu Shut Down or sign out
Ctrl + Alt + Delete Key Combination
You can use the CTRL + ALT + DEL key combination to bring up a full-screen displaying Lock, Sign out,
Change a password, Task Manager and Switch User. If you click the Power icon in the lower right corner of
the screen a power management option menu appears to display Sleep, Hibernate, Shut down, and Restart.
1
Power Options 1 - 39
1
Quick Start Guide
Minimum Screen Resolution Settings
1.Windows 10 has minimum screen resolution requirements.
2.Right-click a blank area of the Desktop and select Display Settings.
3.Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above.
1 - 40 Power Options
Figure 1 - 29 - Display (Resolution)
Storage Devices, Mouse, & Audio
Chapter 2: Storage Devices, Mouse, & Audio
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive/Solid State Drive
•Multi-in-1 Card Reader
•Audio Features
•Touchpad and Buttons/Mouse
2
Overview 2 - 1
Storage Devices, Mouse, & Audio
Bottom Cover
Removal Warning
Do not remove any cover(s) and /or screw(s) for
the purposes of device
upgrade as this may violate the terms of your
warranty.
If you need to replace/
remove the hard disk for
any reason, please contact your distributor/supplier for further
information.
2
Hard Disk Drive/Solid State Drive
The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data
in the computer. The hard disk can be taken out to accommodate other serial (SATA)
hard disk drives (see “Storage” on page D - 2 for specification information), however you will need to contact your distributor/supplier to do this in order to avoid
violating the terms of your warranty.
2 - 2 Hard Disk Drive/Solid State Drive
Storage Devices, Mouse, & Audio
Push-Push Card
Reader
The card reader features a push-in/push-out
card insertion and ejection mechanism. Simply
push the card to insert
and eject it, however Ms
Duo cards require an
adapter.
Figure 2 - 1 |
Left View
1.Card Reader
•MMC (MultiMedia Card) / RSMMC
•SD (Secure Digital) / Mini SD / SDHC / SDXC - up to UHS-II
*Note: Some of these cards require PC adapters that are usually supplied with the cards.
1
Multi-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader” on page 4 - 8).
2
Multi-in-1 Card Reader 2 - 3
Storage Devices, Mouse, & Audio
Volume Adjustment
The sound volume level
can be clicking using the
volume control icon
in the notification areaof the taskbar.
Figure 2 - 2
Realtek Audio
Manager
See “HDMI Audio Configuration” on page C - 9 for a description of the audio configuration
when connecting an HDMI supported display device.
See Sound Blas ter Audio (“Setup for External Speakers/Headphones” on page 6 - 48)
for information on configuring the audio for the best sound balance when using external speakers/headphones.
Right-click the icon to access the menu above, and then
select Sound Manager.
2
Audio Features
You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the notification area icon to bring up an audio menu and select Sound Manager). The volume may also be adjusted by means
of the Fn + F5/F6 key combination (see Table 1 - 5, on page 1 - 20).
2 - 4 Audio Features
Storage Devices, Mouse, & Audio
Volume Adjustment
The sound volume level
is set using the volume
control within Windows
(and the volume function keys on the computer). Click the volume
icon in the notification
area to check the setting.
Headphone
Configuration
It is recommended that
you set the Speaker
Configuration to Stereo (not to 5.1 Speaker)
when listening through
headphones in order to
maximize audio quality.
Figure 2 - 3
Realtek Audio
Manager - Speakers
5.1 Surround
Auto Popup Dialog
You should enable the
auto popup dialog to automatically detect when a
device has been
plugged-in. If disabled,
double-click connectorsettings and click the
box to enable the auto
popup detection of
plugged-n devices.
Connector Settings
Setup for 5.1 Surround Sound
To setup your system for 5.1 surround sound you will need to connect the audio cables to the 2-In-1Audio, Microphone-In and Headphone-Out jacks.
1.Click
2.Click Realtek HD Audio Manager (or right-click the notification area icon and
3.Click Speakers (tab) and click Speaker Configuration (tab).
4.Select 5.1 Speaker from the Speaker Configuration pull-down menu.
Start
and make sure you are in
select Sound Manager).
, and click
Control Panel
Classic View
(or point to
.
Settings
and click
Control Panel
2
)
Audio Features 2 - 5
Storage Devices, Mouse, & Audio
5.Plug in the speaker cables (you may require an adapter to connect each cable to
2
the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers
into the jacks as follows:
•2-In-1 Audio Jack (Line-Out & S/PDIF Combo) = Front Speaker Out
•Microphone-In Jack = Center/Subwoofer Speaker Out
•Headphone Jack = Rear Speaker Out
6.As you plug in each cable a dialog box will pop u.
7.Click to put a check in the appropriate box according to the speaker plugged-in
(e.g. Rear Speaker Out), and then click OK to save the setting.
8.Click OK to exit Realtek HD Audio Manager.
9.See Sound Blaster Audio (“Setup for External Speakers/Headphones” on
page 6 - 48) for information on configuring the audio for the best sound balance
when using external speakers/headphones.
2 - 6 Audio Features
Storage Devices, Mouse, & Audio
Figure 2 - 4
Realtek Audio
Manager -
Recording Setup
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instructions below:
1.Click
2.Click Realtek HD Audio Manager (or right-click the notification area icon and
3.Click Microphone Effects (tab) in Microphone (tab), and then click to select
4.Click OK to close the control panel and save the settings.
Control Panel
select Sound Manager).
Noise Suppression (button), or adjust th e Recording Volume level to around 60,
to obtain the optimum recording quality.
and make sure you are in
Classic View
.
2
Audio Features 2 - 7
Storage Devices, Mouse, & Audio
Auto Pop-Up Dialog
You should enable the
auto pop-up dialog to
automatically detect
when a device has been
plugged-in. If disabled,
double-click connectorsettings and click
the box to enable the
auto pop-up detection of
plugged-n devices.
Figure 2 - 5
Pop-Up Menu for
Audio Devices
2
Setup for Audio Devices - 2-In-1 Audio Jack
To connect either headphones or speakers to the 2-In-1 Audio jack follow the instructions below:
1.Plug either the headphones or speakers in to the 2-In-1 Audio jack .
2.When the pop-up menu appears make sure you select S/PDIF-Out by putting a
check in the box alongside it and clicking OK (failure to do so may result in sound
coming through the connected
the same time).
3.To make sure the pop-up menu appears see sidebar.
4.See Sound Blaster Audio (“Setup for External Speakers/Headphones” on
page 6 - 48) for information on configuring the audio for the best sound balance
when using external speakers/headphones.
headphones/speakers
and the internal speakers at
2 - 8 Audio Features
Storage Devices, Mouse, & Audio
Touchpad Cleaning
In order to improve pad
performance it is necessary to keep the surface
clean and free of fingerprints and marks etc.
Use a soft dry cleaning
cloth to keep the pad
surface clean.
Disabling the Pad
Use the Fn + F1 or Control Center button to disable the Touchpad.
Figure 2 - 6
Touchpad
Sensitivity
Mouse Driver
If you are using an external
mouse your operating system
may be able to auto-configure
your mouse during its installation or only enable its basic
functions. Be sure to check
the device’s user documentation for details.
Touchpad and Buttons/Mouse
The Touchpad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The Touchpad buttons function in
much the same way as a two-button mouse. Make sure you have installed the TouchPad driver (see “Touchpad” on page 4 - 8).
Touchpad Sensitivity
The mouse button zones at the bottom of the pad measure about 15mm from the
bottom of the pad, and the left and right buttons are divided roughly down the mid-
dle. Press the left button zone for a left click, and right button zone for a right click
action.
2
Touchpad and Buttons/Mouse 2 - 9
Storage Devices, Mouse, & Audio
Figure 2 - 7
Windows Settings
> Mouse/Touchpad
2
Mouse & Touchpad Devices
You can configure the functions from the Mouse or Touchpad control panels in Devices in the Settings control panelas follows.
1.Click the
2.Click Devices.
3.Click Mouse or Touchpad.
Settings
item in the
Start Menu
(or
All Settings
in the Action Center).
2 - 10 Mouse & Touchpad Devices
Storage Devices, Mouse, & Audio
Figure 2 - 8
Windows Settings
Mouse
Mouse Settings
You can select the primary mouse button and scrolling options and access Mouse
Properties from Additional mouse options.
2
Mouse & Touchpad Devices 2 - 11
Storage Devices, Mouse, & Audio
Figure 2 - 9
Windows Settings
Touchpad
(
Touchpad turned off
when mouse
connected
)
2
Touchpad Settings
You can disable the Touchpad by clicking the Touchpad button to turn it off.
You can set the system to automatically disable the internal Touchpad when an ex-
ternal USB point device (e.g a USB mouse) is attached. Click “Leave touchpad onwhen a mouse is connected” to off.
2 - 12 Mouse & Touchpad Devices
Storage Devices, Mouse, & Audio
Figure 2 - 10
Windows Settings
Touchpad
Sensitivity & Taps
Touchapd Taps
The Touchpad Sensitiv it y feature helps preven t recogn izing taps on the pad b y accident, by recognizing when your palm is resting on it or brushing its surface while
you are typing.
Click in the check box to enable/disable the different gestures or taps on the surface
of the pad to perform specific actions to manipulate documents, objects and applications.
2
Mouse & Touchpad Devices 2 - 13
Storage Devices, Mouse, & Audio
Figure 2 - 11
Scroll and Zoom/
Scrolling Gesture
Figure 2 - 12
Zooming Gesture
2
Touchapd Scroll and Zoom
Click to enable/disable the two finger scrolling and pinch zooming gesture.
The two-finger scrolling feature works in most scrollable windows and allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
Touchpad surface and slide both fingers in the direction required (in a straight continuous motion).
The two-finger pinch to zoom gesture can be used to perform the same function as
a scroll wheel in Windows applications that support CTRL + scroll wheel zoom
functionality. Place two fingers on the pad (for best results use the tips of the fingers)
and slide them apart to zoom in, or closer together to zoom out.
2 - 14 Mouse & Touchpad Devices
Storage Devices, Mouse, & Audio
Figure 2 - 13
Three-Finger
Gestures
(Swipes & Taps)
Figure 2 - 14
Four-Finger
Gestures
(Swipes & Taps)
The three-finger and four-fingerswipes and taps can be configured for a number
of different functions. Select the appropriate function from the drop-down menu.
2
Mouse & Touchpad Devices 2 - 15
Storage Devices, Mouse, & Audio
Figure 2 - 15
Touchpad
Gesture Examples
2
The following is an overview of some of the main gestures you can use with your
Touchpad, however these can be configured from the Touchpad menus.
2 - 16 Mouse & Touchpad Devices
Chapter 3: Power Management
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
•The Power Sources
•Turning On the Computer
•Power Plans
•Power-Saving States
•Configuring the Power Buttons
•Battery Information
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
3
Overview 3 - 1
Power Management
Forced Off
If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the system to turn itself off.
3
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1.When first setting up the computer use the following procedure (as to safe-
guard the computer during shipping, the battery will be locked to not power the
system until first connected to the AC/DC adapter and initially set up as below):
•Attach the AC/DC adapter cord to the DC-In jack on the left of the computer, then plug
the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter
and leave it there for 6 seconds or longer.
•Remove the adapter cord from the computer’s DC-In jack, and then plug it back in again;
the battery will now be unlocked.
2.Raise the lid/LCD to a comfortable viewing angle.
3.Press the power button icon (make sure to presss the icon directly and not
either side of the icon) to turn the system on.
3 - 2 The Power Sources
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “Battery FAQ” on page 3 - 22).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 18.
Power Management
3
The Power Sources 3 - 3
Power Management
Power Button as Stand by or Hibernate Button
You can use the OS’s “Power Options” control panel to set the power button to send the
system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring
the Power Buttons” on page 3 - 10 for details).
Turning On the Computer
Now you are ready to begin using your computer. To turn it on simply press the pow-
3
er button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options (Hardware and Sound) in the Windows control panel to configure
this feature.
3 - 4 Turning On the Computer
Shutting the Computer Down
Figure 3 - 1
Shut Down/Restart
Note that you should always shut your computer down by choosing the Shut down
command as this will help prevent hard disk or system problems. Right-click the
Power item in the Start Menu and select Shut down. If you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power Menu”
on page 3 - 11.
Power Management
3
You can also use the context menu (right-click the Start Menu
Windows logo + X key combination) to Sign out, Sleep, Hibernate, Shutdown, and Restart.
icon or press the
Shutting the Computer Down 3 - 5
Power Management
Resuming
Operation
See Table 3 - 1, on
page 3 - 12 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 2
Power Plan
Advanced Settings
Power Plans
The computer can be configured to conserve power by means of power plans (Con-
3
trol Panel > Power Options OR Windows Settings > Power & sleep > Additional power settings). You can use (or modify) an existing power plan, or create a new
one.
3 - 6 Power Plans
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Each Windowspower plan will also adjust the processor performance of your ma-
Figure 3 - 3
Power Plans
Click to Show/Hide
additional
power plans
chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
Power Management
3
Power Plans3-7
Power Management
Wake On LAN
Support
Wake-On-LAN is only
supported from Sleep or
Hibernate states in
Windows.
If you require your computer to wake up from
network activity in Windows then make sure
that the computer is either in Sleep or Hiber-nate.
Wake-On-LAN is not
supported from Shutdown states in Win-
dows.
3
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where
you left off. Windows 10 uses the Sleep, Hibernate and Shut Down power-saving
states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.
If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.
To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power
Menu” on page 3 - 11.
3 - 8 Power-Saving States
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.