V14.8.00
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©December 2014
Trademarks
Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
ErP Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode:
• Off Mode < 0.5W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference.
And
2. This device must accept any interference, including interfer ence that may cause undesired operation of the
device.
IV
Preface
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
V
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit:
For Model A - Design II and Model B Designs I & II Computers:
• Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19.5V, 9.23A or 19V, 9.5A (180W) mini-
mum.
For Model A - Design I & V Computers:
• Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19.5V, 9.23A or 19V, 9.5A (180W) mini-
mum.
OR
• Full Range AC/DC Adapter - AC in 100 - 240V, 50 - 60Hz, DC Output 19.5V, 7.7A (150W) minimum.
For Model A Design III & IV Computers and Model B - Design III Computers:
• Full Range AC/DC Adapter - AC in 100 - 240V, 50 - 60Hz, DC Outp ut 19.5V, 7.7A (150W) minimum.
VI
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place where
foreign matter or moisture may
affect the system.
Don’t use or stor e the computer
in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
VII
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until
you properly shut down all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
VIII
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
Servicing
Bottom Cover Removal Warning
Users should not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of
your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your distributor/supplier for further information.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from
the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Preface
IX
Preface
Power Safety Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals and
cables (including telephone lines and power
cord).
You must also remove
your battery in order to
prevent accidentally
turning the machine on.
Before removing the
battery disconnect the
AC/DC adapter from
the computer.
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the powe r co rd, be sure to di sconn ect it b y the plug head , no t
by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
X
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.
• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.
• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
XI
Preface
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
General Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
XII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Cleaning Instructions
(For Computer Models Supplied with Light Blue Cleaning Cloth)
Some computer models in this series come supplied with a light blue cleaning cloth. To clean the computer case
with this cloth follow the instructions below:
1. Power off the computer and peripherals.
2. Disconnect the AC/DC adapter from the computer.
3. Use a little water to dampen the cloth slightly.
4. Clean the computer case with the cloth.
5. Dry the computer with a dry cloth, or allow it time to dry before turning on.
6. Reconnect the AC/DC adapter and turn the computer on.
XIII
Preface
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
Travel Considerations
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your “papers” are handy.
XIV
Packing
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prev ent your
computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both
hardware and software. Make sure your documents are prepared.
Preface
XV
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XVI
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XVII
Preface
Lighting
Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
LCD Electro-Plated Logos
Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp
edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated
logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during
transport. If any such wear and tear develops contact your distributor/supplier.
XVIII
Preface
Contents
Notice .............................................................................................................................................................I
ErP Off Mode Power Consumption Statement: ...........................................................................................II
FCC Statement ............................................................................................................................................IV
FCC RF Radiation Exposure Statement: .....................................................................................................V
Instructions for Care and Operation ......................................................................................................... VII
Servicing .....................................................................................................................................................IX
Power Safety ................................................................................................................................................X
Polymer Battery Precautions ......................................................................................................................XI
General Battery Precautions ..................................................................................................................... XII
Cleaning ...................................................................................................................................................XIII
Cleaning Instructions ...............................................................................................................................XIII
Travel Considerations ..............................................................................................................................XIV
Quick Start Guide
Overview ....................................................................................................................................................1-1
Advanced Users .........................................................................................................................................1-2
Beginners and Not-So-Advanced Users ....................................................................................................1-2
Warning Boxes ..........................................................................................................................................1-2
Not Included ..............................................................................................................................................1-3
System Software ........................................................................................................................................1-4
System Startup ...........................................................................................................................................1-5
XIX
Preface
Model Differences .....................................................................................................................................1-6
LCD Panel Open - Model A ......................................................................................................................1-8
LCD Panel Open - Model A - Designs IV & V .........................................................................................1-9
LCD Panel Open - Model B ....................................................................................................................1-10
LED Indicators .........................................................................................................................................1-11
Illuminated LED Keyboard .....................................................................................................................1-12
Control Center .........................................................................................................................................1-13
Flexikey® Application ............................................................................................................................1-14
Flexikey® Application Features: .............................................................................................................1-15
Keyboard Shortcuts .................................................................................................................................1-16
Function Keys & Visual Indicators .........................................................................................................1-17
Front & Rear Views - Model A ...............................................................................................................1-18
Front & Rear Views - Model B ...............................................................................................................1-19
Right View - Model A .............................................................................................................................1-20
Right View - Model B .............................................................................................................................1-22
Left View - Model A ...............................................................................................................................1-23
Left View - Model B ................................................................................................................................1-24
Bottom View - Model A - Design I .........................................................................................................1-25
Bottom View - Model A - Design II & Design III ..................................................................................1-26
Bottom View - Model A - Design IV & Design V ..................................................................................1-27
Bottom View - Model B ..........................................................................................................................1-28
Windows 8.1 Control Panel .....................................................................................................................1-29
XX
Preface
Windows 8.1 Start Screen & Desktop .....................................................................................................1-32
Apps & Tiles ............................................................................................................................................1-33
Desktop Application ................................................................................................................................1-34
The Charms Bar .......................................................................................................................................1-35
Windows 8.1 Taskbar ..............................................................................................................................1-37
Video Features .........................................................................................................................................1-38
Microsoft Hybrid Graphics ......................................................................................................................1-38
Configuring External Displays ................................................................................................................1-42
Power Options .........................................................................................................................................1-43
Running Apps ..........................................................................................................................................1-44
Storage Devices, Mouse, & Audio
Overview ....................................................................................................................................................2-1
Hard Disk Drive/Solid State Drive ............................................................................................................2-2
Multi-in-1 Card Reader ..............................................................................................................................2-3
Audio Features ...........................................................................................................................................2-4
Setup for Audio Recording ........................................................................................................................2-5
Setup for 5.1Surround Sound ....................................................................................................................2-6
Touchpad and Buttons/Mouse ...................................................................................................................2-8
Touchpad Configuration ............................................................................................................................2-9
Gestures and Device Settings ..................................................................................................................2-10
XXI
Preface
Power Management
Overview ....................................................................................................................................................3-1
The Power Sources ....................................................................................................................................3-2
AC/DC Adapter .........................................................................................................................................3-2
Battery ........................................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-3
Shutting the Computer Down ....................................................................................................................3-4
Power Plans ...............................................................................................................................................3-5
Power-Saving States ..................................................................................................................................3-7
Sleep ..........................................................................................................................................................3-7
Hibernate ....................................................................................................................................................3-8
Shut down ..................................................................................................................................................3-8
Configuring the Power Buttons .................................................................................................................3-9
Resuming Operation ................................................................................................................................3-11
Power Conservation Modes .....................................................................................................................3-12
Battery Information .................................................................................................................................3-14
Battery Power ..........................................................................................................................................3-14
Conserving Battery Power .......................................................................................................................3-15
Battery Life ..............................................................................................................................................3-16
New Battery .............................................................................................................................................3-16
Recharging the Battery with the AC/DC Adapter ...................................................................................3-16
Proper handling of the Battery Pack ........................................................................................................3-17
XXII
Preface
Battery FAQ .............................................................................................................................................3-18
Drivers & Utilities
What to Install ............................................................................................................................................4-1
Module Driver Installation ........................................................................................................................4-1
Driver Installation ......................................................................................................................................4-2
Updating/Reinstalling Individual Drivers ..................................................................................................4-5
User Account Control ................................................................................................................................4-6
Windows Security Message .......................................................................................................................4-6
New Hardware Found ................................................................................................................................4-6
Driver Installation Procedure .....................................................................................................................4-7
Chipset .......................................................................................................................................................4-7
Video (VGA) .............................................................................................................................................4-7
NVIDIA Video (VGA) ..............................................................................................................................4-7
LAN ...........................................................................................................................................................4-7
Card Reader ...............................................................................................................................................4-7
Touchpad ...................................................................................................................................................4-8
Hot Key ......................................................................................................................................................4-8
Airplane .....................................................................................................................................................4-8
MEI Driver .................................................................................................................................................4-8
Audio .........................................................................................................................................................4-8
Optional Drivers ......................................................................................................................................4-10
XXIII
Preface
BIOS Utilities
Overview ....................................................................................................................................................5-1
The Power-On Self Test (POST) ...............................................................................................................5-2
Failing the POST .......................................................................................................................................5-3
Fatal Errors ................................................................................................................................................5-3
Non-Fatal Errors ........................................................................................................................................5-3
The Setup Utility ........................................................................................................................................5-4
Entering Setup ...........................................................................................................................................5-4
Setup Screens .............................................................................................................................................5-5
Main Menu .................................................................................................................................................5-6
System Time & Date (Main Menu) ...........................................................................................................5-6
SATA Port # (Main Menu) ........................................................................................................................5-7
OffBoard SATA Controller Configuration (Main Menu) .........................................................................5-7
System/Extended Memory (Main Menu) ..................................................................................................5-7
MB Series / BIOS Revision / KBC/EC firmware Revision/Mac Address (Main Menu) ..........................5-7
Advanced Menu .........................................................................................................................................5-8
Advanced Chipset Control (Advanced Menu) ..........................................................................................5-8
Combo Slot
(Advanced Menu > Advanced Chipset Control) .......................................................................................5-9
Intel(R) Rapid Start Technology (Advanced Menu) ...............................................................................5-10
Intel(R) Rapid Storage Technology (Advanced Menu) ...........................................................................5-10
SATA Mode (Advanced Menu) ..............................................................................................................5-10
XXIV
Preface
Boot Logo (Advanced Menu) ..................................................................................................................5-11
Power On Boot Beep (Advanced Menu) .................................................................................................5-11
Battery Low Alarm Beep (Advanced Menu) ...........................................................................................5-11
Security Menu ..........................................................................................................................................5-12
Set Supervisor Password (Security Menu) ..............................................................................................5-12
Set User Password (Security Menu) ........................................................................................................5-13
Password on boot: (Security Menu) ........................................................................................................5-13
Secure Boot Control (Security Menu) .....................................................................................................5-14
TPM Configuration (Security Menu) ......................................................................................................5-15
Boot Menu ...............................................................................................................................................5-16
Boot Option Priorities (Boot Menu) ........................................................................................................5-17
UEFI Boot (Boot Menu) ..........................................................................................................................5-17
Exit Menu ................................................................................................................................................5-18
Modules
Overview ....................................................................................................................................................6-1
Setting Up SATA RAID or AHCI Mode ..................................................................................................6-2
AHCI Mode ...............................................................................................................................................6-2
RAID ..........................................................................................................................................................6-2
Intel® Rapid Storage Technology Application .........................................................................................6-2
SATA RAID Setup Procedure (Windows 8.1) ..........................................................................................6-4
IRST Driver Installation ............................................................................................................................6-9
XXV
Preface
Deleting a RAID (Windows 8.1) .............................................................................................................6-10
PC Camera Module ..................................................................................................................................6-11
PC Camera Audio Setup ..........................................................................................................................6-12
Camera App .............................................................................................................................................6-13
Camera Options .......................................................................................................................................6-14
Taking Pictures/Capturing Video ............................................................................................................6-15
Camera Roll .............................................................................................................................................6-16
Wireless LAN Module .............................................................................................................................6-20
3rd Party 802.11b/g/n Driver Installation ................................................................................................6-21
Intel® WLAN Driver Installation ............................................................................................................6-21
Qualcomm Atheros WLAN Combo Driver Installation ..........................................................................6-22
WLAN Configuration in Windows .........................................................................................................6-23
Bluetooth & WLAN Combo Module ......................................................................................................6-26
3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................6-27
Intel Bluetooth Combo Driver Installation ..............................................................................................6-27
Qualcomm Atheros Bluetooth Combo Driver Installation ......................................................................6-28
Bluetooth Configuration in Windows ......................................................................................................6-29
Intel® Rapid Storage Technology ...........................................................................................................6-32
IRST Driver Installation ..........................................................................................................................6-32
Intel® Rapid Storage Technology for RAID Systems ............................................................................6-33
RAID Volume Data Verification and Repair ..........................................................................................6-35
Replacing and Reverting Recovery and Master Volumes .......................................................................6-35
XXVI
Preface
Intel® Smart Response Technology ........................................................................................................6-38
Enabling Intel Smart Response Technology ............................................................................................6-39
Intel® Rapid Start Technology Driver ....................................................................................................6-42
Intel® Rapid Start Technology Configuration ........................................................................................6-43
Intel® Rapid Start Technology Driver Installation .................................................................................6-49
Sound Blaster Audio ................................................................................................................................6-50
Sound Blaster X-Fi MB-3 Audio AP Installation ....................................................................................6-50
Fingerprint Reader Module ......................................................................................................................6-60
Fingerprint Reader Driver Installation .....................................................................................................6-61
Fingerprint Module Configuration ..........................................................................................................6-62
Trusted Platform Module .........................................................................................................................6-64
Enabling & Managing TPM ....................................................................................................................6-65
TPM Management in Windows ...............................................................................................................6-66
TPM Actions ............................................................................................................................................6-68
3G/4G Module .........................................................................................................................................6-70
3G/4G Configuration in Windows ...........................................................................................................6-72
Wireless Display ......................................................................................................................................6-75
Wireless Display Configuration ..............................................................................................................6-76
Troubleshooting
Overview ....................................................................................................................................................7-1
Basic Hints and Tips ..................................................................................................................................7-2
XXVII
Preface
Backup and General Maintenance .............................................................................................................7-3
Viruses .......................................................................................................................................................7-4
Upgrading and Adding New Hardware/Software ......................................................................................7-5
Problems and Possible Solutions ...............................................................................................................7-7
Interface (Ports & Jacks)
Overview ...................................................................................................................................................A-1
Ports and Jacks ..........................................................................................................................................A-2
Card Reader ..............................................................................................................................................A-2
DC-In Jack ................................................................................................................................................A-2
e-SATA / USB 3.0 Combo Port ...............................................................................................................A-3
HDMI-Out Port .........................................................................................................................................A-3
Headphone-Out Jack .................................................................................................................................A-4
Microphone-In Jack ..................................................................................................................................A-4
Mini DisplayPort ......................................................................................................................................A-4
RJ-45 LAN Jack .......................................................................................................................................A-4
S/PDIF-Out Jack .......................................................................................................................................A-4
Security Lock Slot ....................................................................................................................................A-4
USB 3.0 Port .............................................................................................................................................A-5
Powered USB 3.0 Port ..............................................................................................................................A-5
Control Center & Flexikey®
Overview ...................................................................................................................................................B-1
XXVIII
Preface
Control Center ..........................................................................................................................................B-1
Flexikey® .................................................................................................................................................B-1
Power Modes ............................................................................................................................................B-3
Control Center Menus ...............................................................................................................................B-4
Power Status (System Program) .............................................................................................................B-5
Brightness (System Program) ..................................................................................................................B-5
Volume (System Program) .......................................................................................................................B-5
Fan Speed (System Program) ...................................................................................................................B-5
This system supports Energy Star power .............................................................................................B-6
Sleep Button (System Program) ..............................................................................................................B-6
Display Switch (System Program) ...........................................................................................................B-6
Display Utility (System Program for High Definition displays only) .....................................................B-6
Time Zone (System Program) .................................................................................................................B-6
Desktop Background (System Program) .................................................................................................B-6
Backlight Keyboard (Device) ...................................................................................................................B-7
TouchPad/Camera (Device) .....................................................................................................................B-7
Caps Lock/Scroll Lock/ Number Lock/Airplane Mode ...........................................................................B-7
Left Windows Key (Gaming) ..................................................................................................................B-7
Headphone (Gaming) ...............................................................................................................................B-7
Flexikey® (Gaming) .................................................................................................................................B-7
Display Utility (System Program for High Definition displays only) ......................................................B-8
Flexikey® Application ...........................................................................................................................B-11
XXIX
Preface
Language Interface .................................................................................................................................B-12
Keyboard Settings - Express Key ...........................................................................................................B-16
Enabling Time Record ............................................................................................................................B-18
Keyboard Settings - Launch App ...........................................................................................................B-20
Keyboard Settings - Express Text ..........................................................................................................B-22
Keyboard Settings - Disable ...................................................................................................................B-24
Mouse Settings - Express Key ................................................................................................................B-25
Enabling Time Record for Mouse Settings ............................................................................................B-26
Mouse Settings - Launch App ................................................................................................................B-27
Mouse Settings - Express Text ...............................................................................................................B-29
Mouse Settings - Disable ........................................................................................................................B-31
Statistics ..................................................................................................................................................B-32
Video Driver Controls
Overview ...................................................................................................................................................C-1
Microsoft Hybrid Graphics .......................................................................................................................C-2
Video Driver Installation ..........................................................................................................................C-4
Video (VGA) ............................................................................................................................................C-4
NVIDIA Video (VGA) .............................................................................................................................C-4
Intel® Iris(TM) Graphics Control Panel ..................................................................................................C-5
Display Devices & Options ....................................................................................................................C-20
Attaching Other Displays .......................................................................................................................C-21
XXX
Preface
Attaching Other Displays - Devices (Charms Bar) ................................................................................C-24
Configuring an External Display In Windows .......................................................................................C-25
HDMI Audio Configuration ...................................................................................................................C-27
NVIDIA Control Panel ...........................................................................................................................C-30
Customization Options ...........................................................................................................................C-32
Set PhysX® Configuration .....................................................................................................................C-36
Specifications
Processor ...................................................................................................................................................D-2
Core Logic ................................................................................................................................................D-2
Display ......................................................................................................................................................D-2
Memory .....................................................................................................................................................D-2
Video Adapter Options .............................................................................................................................D-2
Storage ......................................................................................................................................................D-3
Audio ........................................................................................................................................................D-3
Keyboard & Pointing Device ....................................................................................................................D-3
Indicators ..................................................................................................................................................D-3
Interface ....................................................................................................................................................D-4
Card Reader ..............................................................................................................................................D-4
Slots ..........................................................................................................................................................D-4
Communication .........................................................................................................................................D-4
Operating System ......................................................................................................................................D-4
XXXI
Preface
BIOS .........................................................................................................................................................D-4
Features .....................................................................................................................................................D-5
Security .....................................................................................................................................................D-5
Power Management ..................................................................................................................................D-5
Power ........................................................................................................................................................D-5
Environmental Spec ..................................................................................................................................D-5
Physical Dimensions & Weight ................................................................................................................D-5
XXXII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk and
card reader), TouchPad & Mouse and Audio Features.
• Chapter 3 The computer’s power management options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 A quick guide to the computer’s PC Camera, Wireless LAN, Fingerprint, Bluetooth & WLAN
Combo, Sound Blaster Audio and Intel modules (some of which may be optional depending on
your purchase configuration).
• Chapter 7 A troubleshooting guide.
• Appendix A Definiti ons of the interface, ports/jacks which allow your computer to c ommun icat e with ex te rnal
devices.
• Appendix B Information on the Control Center . and Flexikey® Application.
• Appendix C Information on the Video driver controls.
• Appendix D The computer’s specification.
1
Overview 1 - 1
1
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the User’s Manual. You
may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4
- 4. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers
& Utilities” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
Not Included
Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
1
Overview 1 - 3
1
Windows OS
Note that the information included on the following pages is for Windows 8.1 only.
In order to run Windows 8/8.1 (64 bit) your computer requires a minimum 2GB of system memory (RAM).
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the Windows 8.1 o perating system is supported.
1 - 4 Overview
Quick Start Guide
135°
Shutdown
Note that you should always
shut your computer down by
choosing the Shut Down
command in Windows (see
page 1 - 43). This will help
prevent hard disk or system
problems.
System Startup
1. Remove all packing materials, and place the computer on a stable surface, and securely attach any peripherals
you want to use with the notebook (e.g. keyboard and mouse) to their ports.
2. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter (make sure you use the adapter when first
setting up the computer, as to safeguard the computer during shipping, the battery will be locked to not power
the system until first connected to the AC/DC adapter).
3. Use one hand to raise the
the other hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).
4. Press the power button on the top of the computer for about 2 - 3 seconds to turn the computer “on” (note that
the power LED on the front of the computer will turn from orange to green when the computer powers on).
lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);
Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD
System Startup 1 - 5
use
1
1
Quick Start Guide
Model Differences
This notebook series includes two different model types, which include different design styles, that mainly differ as
indicated in the table below and overleaf. Note that your model may appear slightly different from those pictured in
this manual.
Feature
Design I Design II Design III Design IV Design V
Display Type
Video
Adapter
Storage See “Storage” on page A - 3 for the details of storage options for each model
3G/4G Module LTE/HSPA+ M.2 3042 3G or 4G Module Card (optional) with USB Interface
Subwoofer
Speaker
Dimensions &
Weight
15.6" (39.62cm) QFHD (3840 * 2160) / WQHD+
(2880 * 1620) / FHD (1920 * 1080) 3.5mm 16:9
Backlit Panel
NVIDIA® GeForce GTX
970M
See “Physical Dimensions & Weight” on page A - 5 for the details of the dimensions and weight for each model and
design (note the Model A Design IV & V pictures in Figure 1 - 3 on page 1 - 9, Figure 1 - 8 on page 1 - 18 & Figure 1 - 17
NVIDIA® GeForce GTX
980M
Model A
15.6" (39.62cm) QFHD (3840 * 2160) / FHD
(1920 * 1080) 3.5mm 16:9 Backlit Panel
NVIDIA® GeForce GTX 965M
Not Supported
on page 1 - 27)
Table 1 - 1 - Model Differences
1 - 6 Model Differences
15.6" (39.62cm)
QFHD (3840 * 2160)
/ WQHD+ (2880 *
1620) / FHD (1920 *
1080) 3.5mm 16:9
Backlit Panel
NVIDIA® GeForce
GTX 970M
Quick Start Guide
1
Feature
Design I Design II Design III
Display Type
Video Adapter NVIDIA® GeForce GTX 970M NVIDIA® GeForce GTX 980M NVIDIA® GeForce GTX 965M
Storage See “Storage” on page A - 3 for the details of storage options for each model
3G/4G Module Not Supported
Subwoofer Speaker One Built-In Subwoofer Speaker
Dimensions & Weight
See “Physical Dimensions & Weight” on page A - 5 for the details of the dimensions and weight for each
17.3" (43.94cm) FHD (1920 * 1080) 6.0mm,
Model B
16:9 Backlit Panel
model and design
Table 1 - 2 - Model Differences
Model Differences 1 - 7
1
Figure 1 - 2
LCD Panel Open
Model A
1. Built-In PC Camera
2. PC Camera LED
3. Built-In Array
Microphone
4. LCD
5. Speakers
6. Power Button
7. Illuminated LED
Keyboard
8. TouchPad & Buttons
9. Fingerprint Reader
Sensor (Optional)
8
Note that the Touchpad/
Clickpad and Buttons has a
valid operational area indicated within the dotted lines
above.
4
1
9
5
8
6
7
2
5
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
(e.g. WLAN, Bluetooth or
3G/4G) aboard aircraft is
usually prohibited. Make
sure any wireless modules
are OFF (i.e. the system is in
Airplane Mode) if you are
using the computer aboard
aircraft.
Use Fn + F11 Airplane
Mode key combination to
toggle Airplane Mode On/
Off, and check the LED indicator for the power status.
3
Quick Start Guide
LCD Panel Open - Model A
1 - 8 LCD Panel Open - Model A
LCD Panel Open - Model A - Designs IV & V
Figure 1 - 3
LCD Panel Open
Model A Designs IV & V
1. Built-In PC Camera
2. PC Camera LED
3. Built-In Array
Microphone
4. LCD
5. Speakers
6. Power Button
7. Illuminated LED
Keyboard
8. TouchPad & Buttons
9. Fingerprint Reader
Sensor (Optional)
8
Note that the Touchpad/
Clickpad and Buttons has a
valid operational area indicated within the dotted lines
above.
4
1
9
5
8
6
7
2
5
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
(e.g. WLAN, Bluetooth or
3G/4G) aboard aircraft is
usually prohibited. Make
sure any wireless modules
are OFF (i.e. the system is in
Airplane Mode) if you are
using the computer aboard
aircraft.
Use Fn + F11 Airplane
Mode key combination to
toggle Airplane Mode On/
Off, and check the LED indicator for the power status.
3
Quick Start Guide
1
LCD Panel Open - Model A - Designs IV & V 1 - 9
1
Figure 1 - 4
LCD Panel Open
Model B
1. Built-In PC Camera
2. PC Camera LED
3. Built-In Array
Microphone
4. LCD
5. Speakers
6. Power Button
7. Illuminated LED
Keyboard
8. TouchPad & Buttons
9. Fingerprint Reader
Sensor (Optional)
8
Note that the Touchpad/
Clickpad and Buttons has a
valid operational area indicated within the dotted lines
above.
4
1
9
5
8
6
7
2
5
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
(e.g. WLAN, Bluetooth or
3G/4G) aboard aircraft is
usually prohibited. Make
sure any wireless modules
are OFF (i.e. the system is in
Airplane Mode) if you are
using the computer aboard
aircraft.
Use Fn + F11 Airplane
Mode key combination to
toggle Airplane Mode On/
Off, and check the LED indicator for the power status.
3
Quick Start Guide
LCD Panel Open - Model B
1 - 10 LCD Panel Open - Model B
Quick Start Guide
LED Indicators
The LED indicators display helpful information about the current status of the computer.
Icon Color Description Icon Color Description
1
Green
Green
Green
Green Hard Disk Activity Orange AC/DC Power is Plugged In
Green
Off Integrated GPU (iGPU) In Use Green The Computer is On
Green Discrete GPU (dGPU) Is Powered Blinking Green The Computer is in Sleep Mode
Airplane Mode is ON (the WLAN, Bluetooth
Number Lock is Activated
Caps Lock is Activa ted
Scroll Lock is Activated
& 3G/4G Modules are OFF)
Orange The Battery is Charging
Blinking Orange
Green The Battery is Fully Charged
Blinking Orange*
The Battery has Reached Critically Low
Power Status
The Powered USB Port is On
“Powered USB 3.0 Port” on page 1 - 23
(see
Table 1 - 3 - LED Indicators
LCD Panel Open - Model B 1 - 11
)
1
Other Keyboards
If your keyboard is damaged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it automatically. However special functions/hot-keys
unique to the system’s
regular keyboard may not
work.
Scr Lk
Hold down the Fn Key
and Scr Lk to enable
scroll lock/number lock,
and check the LED indicator for status.
Numerical
Play/Pause Key
Function Keys
Scr Lk Key
Fn Key
Game Control Keys
Num Lk Key
Windows Logo Key
Menu/Application Key
Numerical
Keypad
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.
Quick Start Guide
Illuminated LED Keyboard
The illuminated keyboard has an embedded numerical keypad for easy numeric data
input, and features function keys to allow you to change operational features instantly. See Table 1 - 5, on page 1 - 17 for full function key combination details.
1 - 12 Illuminated LED Keyboard
Figure 1 - 5 - Illuminated LED Keyboard
Quick Start Guide
Control Center Access
To run the Control Center press the Fn + Esc key
combination, or double-click
the icon in the notification
area of the taskbar.
Close the Control Center by
clicking the close icon in
the top right of the panel
(move the cursor onto the top
right corner of the panel to
highlight it).
Control Center
When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or
double-click the icon
trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch
Pad on/off (see Appendix B for full details).
in the notification area of the taskbar to toggle the Control Center on/off. The Con-
Figure 1 - 6 - Control Center
Control Center 1 - 13
1
1
Flexikey® Enabled
Flexikey® Disabled
Quick Start Guide
Flexikey® Application
The Flexikey® application is a quick hotkey configuration application, which allows you to assign a single key
to launch multiple key combinations, or to launch programs and applications, to create text macros and to
disable certain keys. The application can also be used to configure the mouse buttons to create hotkeys for
gaming etc. All the configuration settings are retained under (up to12) profiles to which the settings are applied.
Click Flexikey® in the Gaming section of the Control Center, or the click the icon in the notification
area of the taskbar, to launch the application (see Appendix B for full details).
1 - 14 Flexikey® Application
Figure 1 - 7 - Flexikey® Hotkey Application
Quick Start Guide
Flexikey® Application Features:
For full details see “Flexikey® Application” on page B - 11.
• EXPRESS KEY - This feature allows you to configure a single key (or mouse click) to send multiple key
combinations, or to create more useful shortcut keys This is useful in gaming or when using applications
which have a complex set of keyboard shortcuts.
• LAUNCH APP - This simply assigns single keys (or mouse clicks) to launch any program’s or applica-
tion’s executable file.
• EXPRESS TEXT - With this you can assign single keys (or mouse clicks) to send commonly used strings
of text.
• DISABLE - Use this function to disable any keyboard keys or mouse buttons.
• STATISTICS - Use this to quickly record keys in use in any application, and to disable unused keys.
1
Flexikey® Application 1 - 15
1
Windows Logo
Keyboard Shortcut
Use the Windows logo
key + D key com-
bination to switch between the Start screen
and Windows Desktop.
Menu/Application
Keyboard Shortcut
When the Desktop app
is running you can use
the Menu/Application
key on the keyboard to display the
context menu as per a
mouse right-click. In
the Start screen this
function is useful to
quickly display the All
Apps icon.
Quick Start Guide
Keyboard Shortcuts
The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in
Windows 8.1
.
1 - 16 Flexikey® Application
Windows Logo
Key +
Tap Winkey
CDisplay Charms menu
D Switch to the Windows Desktop and toggle show Desktop
E
F Display file Search
I Open the Settings charm
K Open the Connect charm
L Lock the computer and display the Lock screen
P Display the Second Screen menu (see Figure 1 - 30 on page 1 - 42)
R Switch to the Windows Desktop and display the Run dialog box
Z Access the Customize Bar (see Figure 1 - 22 on page 1 - 33)
Description
Toggle between the Start screen and the foremost running app or the
Windows Desktop
Switch to the Windows desktop and launch Windows Explorer with
Computer displayed
Table 1 - 4 - Keyboard Shortcuts
Quick Start Guide
Function Keys & Visual Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.
Keys Function/Visual Indicators Keys Function/Visual Indicators
1
Fn +
Fn +
Fn +
Fn +
Fn +
Fn +
Fn +
Fan Control
Toggle Automatic /
Full Power
Play/Pause (in Audio/Video Programs)
Touchpad Toggle
Turn LCD Backlight Off
(Press a key to or use Touchpad to turn on)
Mute Toggle
Keyboard LED Toggle
Volume Decrease/Increase Fn + Power Button Powered USB 3.0 Port Power Toggle
Table 1 - 5 - Function Keys & Visual Indicators
Fn +
Fn +
Fn +
Fn +
Fn +
Fn +
Fn + Backspace Flexikey® Enable/Disable
Control Center Toggle (see over)
Display Toggle
Brightness Decrease/Increase
PC Camera
Power T oggle
Airplane
Mode Toggle
Sleep Toggle
Flexikey® Application 1 - 17
1
Figure 1 - 8
Front & Rear Views
Model A
1. LED Power Indicators
2. Vent/Fan Intake
3. DC-In Jack
4. Combined eSATA/
USB 3.0 Port
USB Ports
Note that the connections to
the USB ports only fit one
way, do not force them.
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/
fan intake(s) while the computer is in use.
1
3
4
2
1
E-SATA Cable Insertion
E-SATA cables should be inserted as illustrated below (with the T-Shape inverted, the
pins at the lower half of the connector). ESATA cables only fit one way, do not force
them.
Design I & Design III
Design II
2
3
4
Design IV & Design V
2
3
4
Quick Start Guide
Front & Rear Views - Model A
1 - 18 Front & Rear Views - Model A
Front & Rear Views - Model B
Figure 1 - 9
Front & Rear Views
Model B
1. LED Power Indicators
2. Vent/Fan Intake
3. DC-In Jack
4. Combined eSATA/
USB 3.0 Port
USB Ports
Note that the connections to
the USB ports only fit one
way, do not force them.
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/
fan intake(s) while the computer is in use.
1
3
4
2
1
E-SATA Cable Insertion
E-SATA cables should be inserted as illustrated below (with the T-Shape inverted, the pins
at the lower half of the connector). E-SATA cables only fit one way, do not force them.
Quick Start Guide
1
Front & Rear Views - Model B 1 - 19
1
Figure 1 - 10
Right View
Model A
1. S/PDIF-Out Jack
2. Microphone Jack
3. Headphone Jack
4. Multi-in-1 Card
Reader
5. SIM Card Reader
(for 3G/4G USIM
Cards - see over)
6. 2 * USB 3.0 Ports
7. RJ-45 LAN Jack
8. Security Lock Slot
USB Ports
Note that the connections to the USB ports
only fit one way, do not
force them.
1 3
4
2
6
8
5
Multi-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
6
7
Inserting Cards into the Card Reader
Note that the cards should
be inserted with the read-
able side of the card facing upwards, as
illustrated on the right.
Quick Start Guide
Right View - Model A
1 - 20 Right View - Model A
3G/4G Module USIM Card Installation
USIM Card Orienta-
tion
Note that the USIM
card’s readable side
(with the gold-colored
contacts) should face
upwards as illustrated.
Figure 1 - 11
USIM Card Insertion
1
1
USIM Card Ejection
Simply press on the USIM card to eject it, however do not do this while a connection is in
progress.
If you do eject the card while a 3G/4G connection is ongoi ng, you will need to sh ut down
the system, reinsert the USIM card, restart the system and then reestablish the 3G/4G connection.
If you wish to change USIM cards then you will need to shut the system down, reinsert the
USIM card, restart the system and then reestablish the 3G/4G connection.
(For Model A Computers Only)
Insert the USIM card as illustrated below (pay careful attention to the orientation
of the card as the gold contact side of the card should face upwards) until it clicks
fully into position. To eject the card simply press it until it ejects, but do not attempt
to eject the card while connected to a 3G/4G network (see below).
Quick Start Guide
1
Right View - Model A 1 - 21
1
Figure 1 - 12
Right View
Model B
1. S/PDIF-Out Jack
2. Microphone Jack
3. Headphone Jack
4. 2 * USB 3.0 Ports
5. Multi-in-1 Card
Reader
6. RJ-45 LAN Jack
7. Security Lock Slot
USB Ports
Note that the connections to the USB ports
only fit one way, do not
force them.
1 3
4
2
65
Multi-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
7
Inserting Cards into the Card Reader
Note that the cards should
be inserted with the read-
able side of the card facing upwards, as illustrated
on the right.
4
Quick Start Guide
Right View - Model B
1 - 22 Right View - Model B
Left View - Model A
Figure 1 - 13
Left View - Model A
1. Vent/Fan Intake
2. HDMI-Out Port
3. 1 * Powered USB
3.0 Port
4. Mini Display Port 2
5. Mini Display Port 1
1
2
4
3
Powered USB 3.0 Port
USB 3.0 ports are denoted by their blue color. Note that the USB 3.0 port is not operational
under DOS and does not support wake on USB. The powered USB 3.0 ( in Figure 1 -
13 on page 1 - 23) port can supply power (for charging devices only, not for operating
devices) when the system is off but still powered by the AC/DC adapter plugged into a
working outlet, or powered by the battery with a capacity level above 20% (this may not
work with certain devices - see page 7 - 11). Toggle power to this port by using Fn + power
button.
HDMI Port / Mini Display Port
Note that the HDMI Port and Mini Display ports support video and audio signals to attached
external displays (see “HDMI Audio Configuration” on page C - 27).
Note that Sound Blaster X-Fi MB3 audio will be disabled when you are connecting to an
external display through an HDMI or Mini Display port connection.
3
5
Quick Start Guide
1
Left View - Model A 1 - 23
1
Figure 1 - 14
Left View - Model B
1. Vent/Fan Intake
2. HDMI-Out Port
3. 1 * Powered USB
3.0 Port
4. Mini Display Port 2
5. Mini Display Port 1
1
2
4
3
Powered USB 3.0 Port
USB 3.0 ports are denoted by their blue color. Note that the USB 3.0 port is not operational
under DOS and does not support wake on USB. The powered USB 3.0 ( in Figure 1 -
13 on page 1 - 23) port can supply power (for charging devices only, not for operating
devices) when the system is off but still powered by the AC/DC adapter plugged into a
working outlet, or powered by the battery with a capacity level above 20% (this may not
work with certain devices - see page 7 - 11). Toggle power to this port by using Fn + power
button.
HDMI Port / Mini Display Port
Note that the HDMI Port and Mini Display ports support video and audio signals to attached
external displays (see “HDMI Audio Configuration” on page C - 27).
Note that Sound Blaster X-Fi MB3 audio will be disabled when you are connecting to an
external display through an HDMI or Mini Display port connection.
3
5
Quick Start Guide
Left View - Model B
1 - 24 Left View - Model B
Bottom View - Model A - Design I
Figure 1 - 15
Bottom View
Model A - Design I
1. Fan Outlet/Intake
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/
fan intake(s) while the computer is in use.
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/
optical device etc., for any
reason, please contact your
distributor/supplier for further information.
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions.
1
1 1
1
1
Quick Start Guide
1
Bottom View - Model A - Design I 1 - 25
1
Figure 1 - 16
Bottom View
Model A - Designs II &
III
1. Fan Outlet/Intake
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/fan
intake(s) while the computer
is in use.
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/optical device etc., for any
reason, please contact your
distributor/supplier for further
information.
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions.
1
1
1
1
1
Quick Start Guide
Bottom View - Model A - Design II & Design III
1 - 26 Bottom View - Model A - Design II & Design III
Bottom View - Model A - Design IV & Design V
Figure 1 - 17
Bottom View
Model A - Designs IV
& V
1. Fan Outlet/Intake
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/fan
intake(s) while the computer
is in use.
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/optical device etc., for any
reason, please contact your
distributor/supplier for further
information.
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions.
1 1
1
1
1
Quick Start Guide
1
Bottom View - Model A - Design IV & Design V 1 - 27
1
Figure 1 - 18
Bottom View - Model B
1. Fan Outlet/Intake
2. Subwoofer Speaker
Overheating
To prevent your computer
from overheating make sure
nothing blocks the vent(s)/
fan intake(s) while the computer is in use.
Bottom Cover Removal
Warning
Do not remove any cover(s)
and /or screw(s) for the purposes of device upgrade as
this may violate the terms of
your warranty.
If you need to replace/remove the hard disk/RAM/
optical device etc., for any
reason, please contact your
distributor/supplier for further information.
1
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions.
1
2
1
1
1
Quick Start Guide
Bottom View - Model B
1 - 28 Bottom View - Model B
Windows 8.1 Control Panel
Windows Versions
Note that the information included on the following pages is for the
latest updated version
of Windows 8.1 only.
Make sure you enable
Windows Update in order to get all the latest
security updates etc.
(see “Windows Up-
date” on page 4 - 9).
Move the mouse to the bottom left
Start Screen
Desktop app
of the screen and right-click to
access the menu.
Throughout this manual you will see an instruction to open the Control Panel.
R
ight-click the lower left hot corner to bring up the context menu (or use the Win-
dows Logo Key + X key combination)
Desktop app or Start screen.
and select Control Panel in both the
Quick Start Guide
1
Figure 1 - 19 - Windows Context Menu
Windows 8.1 Control Panel 1 - 29
1
Keyboard Shortcut to Control Panel
You can also use keyboard shortcuts to access the Contro l Pa nel. Press th e Win dows logo key and X to bring up
the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R
to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.
Quick Start Guide
The Control Panel can be accessed in a number of ways in Windows 8.1.
•Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type
Control Panel and select it from the results to the left.
• Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the
top menu and select Open Control Panel from the ribbon.
• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows
Charms Bar and select Control Panel from the menu.
• Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System).
• Right-c lick the Start button to bring up the menu and select Control Panel (see Figure 1 - 20 on page 1
- 31).
1 - 30 Windows 8.1 Control Panel
Right-click the Start button in the Desktop app (or use the Windows Logo Key
Display Most
Recently Used
Apps
If you are in the Start
screen, Desktop or an
app you can move your
mouse to the upper left
corner of the screen to
get back to the most recently used app.
To view all the most recently used Apps hover
over the top left of the
screen and then move
the mouse down along
the left side of the
screen to display the
list.
Move the mouse to the bottom left of the screen
and right-click the Start button to access the menu.
+ X key combination) to bring up an advanced context menu of useful features
such as Control Panel, Programs and Features, Power Options, Task Manager,
Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
Figure 1 - 20 - Advanced Context Menu (Right-Click Start Button)
Quick Start Guide
1
Windows 8.1 Control Panel 1 - 31
1
Desktop App
Quick Start Guide
Windows 8.1 Start Screen & Desktop
The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or
Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking
the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the
arrow at the bottom of the Start screen to access Apps.
Figure 1 - 21 - Windows Start Screen
1 - 32 Windows 8.1 Start Screen & Desktop
Quick Start Guide
Click the arrow at the bottom of the
screen to access All Apps
Apps & Tiles
The Start screen will contain a number of apps, and many more will be installed as you add more applications
etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen
in order to view all the necessary Apps.
Accessing Pining/Unpinning All Apps
You can add and remove the tiles for apps and control panels in the Start screen. Right-click on an app to bring
up the context menu and you pin the App to (or unpin from) the Start screen, or to the taskbar.
1
Figure 1 - 22 - Apps
Windows 8.1 Start Screen & Desktop 1 - 33
1
Move the mouse to the bottom left of the screen and click to switch
back to the Start screen.
Quick Start Guide
Desktop Application
When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key
combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop
app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click.
Figure 1 - 23 - Desktop
1 - 34 Windows 8.1 Start Screen & Desktop
The Charms Bar
Move the mouse over a Charms Bar icon to activate the menu
Move the mouse to the top/lower right icons to activate the Charms Bar
Move the mouse to the top/lower right icons to activate the Charms Bar
The right side of the screen (Start or Desktop) displays the Charms Bar. The Charms Bar contains the Search,
Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower
right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will
be black when it is active), or use the Windows Logo Key + C key combination.
Quick Start Guide
1
Figure 1 - 24 - Start Screen with Charms Bar
Windows 8.1 Start Screen & Desktop 1 - 35
1
Charms Bar - TouchPad Access
To quick access the Charms Bar using the TouchPad:
1. Place your finger off the TouchPad (slightly to the right of the
pad resting on the computer).
2. Move your finger across to the left on to the TouchPad.
3. The Charms Bar will then pop-up.
Quick Start Guide
Charms Bar Items
• Search : You can search for any file, application, Apps and control panel settings with instantaneous
results.
•Share : This button is used to share information with people via mail or social networks.
•Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or click-
ing the bottom left of the screen).
• Devices : Click this button to change connected peripheral device settings e.g. an external display.
• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).
Figure 1 - 25 - Settings Menu
1 - 36 Windows 8.1 Start Screen & Desktop
Quick Start Guide
Windows 8.1 Taskbar
In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar can be directly accessed from the Desktop application; if you
are in the Start screen you will need to move the cursor to the bottom of the screen to display the taskbar.
The taskbar is displayed at the bottom of the screen, and you can see the notification area (system tray) of the
taskbar in the bottom right of the screen. Some of the control panels and applications referred to during the
course of this manual can be accessed from here.
1
Figure 1 - 26 - Taskbar & Notification Area (System Tray)
You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing
Pining/Unpinning All Apps” on page 1 - 33).
Windows 8.1 Start Screen & Desktop 1 - 37
1
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display control panel (in Appearances
and Personalization) in Windows when running the Desktop app (see “Desktop Application ” on page 1 - 34).
Microsoft Hybrid Graphics
Your computer will feature Microsoft Hybrid Graphics switchable graphics technology. This seamless technology is designed to get best performance from the graphi cs system while allowing longer battery life, without
having to manually change settings. The computer’s operating system (and some applications) will automati-
cally switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU
(dGPU) when required by the applications in use. This switch is seamless to the user (see Appendix C).
Icon Color Description
Off Integrated GPU (iGPU) In Use
Green Discrete GPU (dGPU) Is Powered
Table 1 - 6 - GPU Mode LED Indicator
The basic video features for this computer can be configured using the Intel® Iris™ Graphics Control Panel.
Further video configuration is available through the NVIDA control panel (see the information on the following
pages and Appendix C).
1 - 38 Video Features
Quick Start Guide
3
2
Right-Click Desktop App
1. You can right-click the
desktop and select
Screen resolution
(Figure 1 - 27).
2. Use the dropbox to
select the screen
Resolution (Figure
1 - 27).
3.Click Advanced
settings (Figure 1 -
27) to bring up the
Advanced properties
tabs.
123
1
1
To access Display (Control Panel) and Screen Resolution in Windows:
1. Go to the Control Panel.
2. Click Display (icon) - In the Appearance and Personalization category.
3. Adjust resolution.
Figure 1 - 27 - Screen Resolution
Video Features 1 - 39
1
3
4
4
Quick Start Guide
To access the Intel(R) Iris(TM) Graphics Control Panel:
1. Click Advanced settings (Figure 1 - 27 on page 1 - 39) in the Screen Resolution control panel in Windows.
2. Click the Intel(R)... tab and click Graphics Properties (button) (Figure 1 - 28 on page 1 - 40) .
OR
3. Right-click the desktop and select Graphics Properties from the menu.
OR
4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.
Figure 1 - 28 - Intel Iris Graphics Control Panel
1 - 40 Video Features
To access the NVIDIA Control Panel:
5
6
5
6
1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 29).
OR
2. Double-click the icon (Figure 1 - 29) in the Windows control panel.
Quick Start Guide
1
Figure 1 - 29 - NVIDIA Control Panel
Video Features 1 - 41
1
Quick Start Guide
Configuring External Displays
It is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The
Charms Bar” on page 1 - 35).
To Configure Displays from Devices (Charms Bar):
1. Attach your display to the appropriate port, and turn it on.
2. Go the Charms Bar, select Devices.
3. Click Project (you may need to click Second Screen).
4. Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen
only.
1 - 42 Video Features
Figure 1 - 30- Devices (Project)
Quick Start Guide
Charms Bar
Desktop App Start Screen
Power Button Start Screen
Power Options
Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set-
tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/
Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10). You can also use the
context menu (Shut down or sign out) shut the computer down/restart etc.
1
Figure 1 - 31 - Shut Down/Restart
Power Options 1 - 43
1
Screen Resolution for Apps
(Windows 8.1)
The minimum resolution in which Apps will run is 1024x768.
The minimum resolution required to support all the fe atures of
Windows 8 (including multitasking with snap) is 1366x768.
These specs are the minimum screen resolution that supports
all the features of Windows 8.1 on a useful physical size.
Quick Start Guide
Running Apps
To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements.
Screen Resolution Settings
1. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).
2. Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to
make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).
1 - 44 Running Apps
Figure 1 - 32 - Screen Resolution
Quick Start Guide
User Account Control Settings
If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you
have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off.
To check whether the UAC is on or off, follow the instructions below.
1. Open the Control Panel.
2. Click on User Accounts and then click on Change User Account Control settings (or click System and
Security and click Change User Account Control Settings under Action Center).
3. If the slider is in the Never notify position, then the UAC is disabled.
4. To enable or turn on the UAC, move the slider to Always notify or Notify me when apps try to make changes
to my computer (default) position, and then click OK.
1
Figure 1 - 33 - User Account Control Settings
Running Apps 1 - 45
1
Quick Start Guide
1 - 46
Storage Devices, Mouse, & Audio
Chapter 2: Storage Devices, Mouse, & Audio
Overview
Read this chapter to learn more about the following main features and components
of the computer:
• Hard Disk Drive/Solid State Drive
• Multi-in-1 Card Reader
• Audio Features
• Touchpad and Buttons/Mouse
2
Overview 2 - 1
Storage Devices, Mouse, & Audio
Bottom Cover
Removal Warning
Do not remove any cover(s) and /or screw(s) for
the purposes of device
upgrade as this may violate the terms of your
warranty.
If you need to replace/
remove the hard disk for
any reason, please contact your distributor/supplier for further
information.
2
Hard Disk Drive/Solid State Drive
The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data
in the computer. The hard disk can be taken out to accommodate other serial (SATA)
hard disk drives (see “Storage” on page D - 3 for specification information), however you will need to contact your distributor/supplier to do this in order to avoid
violating the terms of your warranty.
2 - 2 Hard Disk Drive/Solid State Drive
Storage Devices, Mouse, & Audio
Push-Push Card
Reader
The card reader features a push-in/push-out
card insertion and ejection mechanism. Simply
push the card to insert
and eject it, however Ms
Duo cards require an
adapter.
Figure 2 - 1
Right Views
1. Card Reader
Inserting Cards
into the Card
Reader
Note that the cards
should be inserted
with the readable
side of the card facing upwards, as il-
lustrated on the right.
1
1
• MMC (MultiMedia Card) / RSMMC
• SD (Secure Digital) / Mini SD / SDHC / SDXC
*Note: Some of these cards require PC adapters that are usually supplied with the cards.
Multi-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader” on page 4 - 7).
2
Multi-in-1 Card Reader 2 - 3
Storage Devices, Mouse, & Audio
Volume Adjustment
The sound volume level
can be set using the volume control in the Set-
tings menu in the
Charms Bar.
Figure 2 - 2
Realtek Audio
Manager
See “HDMI Audio Configuration” on page C - 27 for a description of the audio configuration
when connecting an HDMI supported display device.
See “Sound Blaster Audio & HDMI/Mini Display Port ” on page 6 - 58 for more information
on the THX TruStudio Pro Audio setup.
Right-click the icon to access the menu above, and then
select Sound Manager.
2
Audio Features
You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the notification area icon to bring up an au-
2 - 4 Audio Features
dio menu and select Sound Manager). The volume may also be adjusted by means
of the Fn + F5/F6 key combination (see Table 1 - 5, on page 1 - 17).
Storage Devices, Mouse, & Audio
Headphone
Configuration
It is recommended that
you set the Speaker
Configuration to Stereo when listening
through headphones in
order to maximize audio
quality.
Figure 2 - 3
Realtek Audio
Manager -
Recording Setup
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instructions below:
1. Click
2. Click Realtek HD Audio Manager (or right-click the notification area icon and
3. Click Microphone Effects (tab) in Microphone (tab), and then click to select
4. Click OK to close the control panel and save the settings.
Control Panel
select Sound Manager).
Noise Suppression (button), or adjust th e Recording Volume level to around 60,
to obtain the optimum recording quality.
and make sure you are in
Classic View
2
.
Audio Features 2 - 5
Storage Devices, Mouse, & Audio
Sound Blaster Audio &
HDMI
Note that the Sound
Blaster audio effects do
not apply to audio generated through an HDMI
connection (see page 6
- 50.).
Figure 2 - 4
Speaker
Configuration (5.1)
Auto Popup Dialog
You should enable the
auto popup dialog to automatically detect when a
device has been
plugged-in. If disabled,
double-click connector
settings and click the
box to enable the auto
popup detection of
plugged-n devices.
Connector Settings
2
2 - 6 Audio Features
Setup for 5.1Surround Sound
To setup your system for 5.1 surround sound you will need to connect the audio cables to the Headphone-Out, Microphone-In jack and S/PDIF-Out jacks.
1. Click
2. Click Realtek HD Audio Manager (or right-click the notification area icon and
3. Click Speakers (tab) and click Speaker Configuration (tab).
4. Select 5.1 Speaker from the S peaker Configuration pull-down menu.
Start
, and click
and make sure you are in
select Sound Manager).
Control Panel
(or point to
Classic View
Settings
.
and click
Control Panel
)
Storage Devices, Mouse, & Audio
5. Plug in the speaker cables (you may require an adapter to connect each cable to
the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers
into the jacks as follows:
• Headphone-Out Jack = Side Speaker Out
• Microphone-In Jack = Center/Subwoofer Speaker Out
• S/PDIF-Out Jack = Front Speaker Out
6. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on
page 2 - 6).
7. Click to put a check in the appropriate box according to the speaker plugged-in
(e.g. Rear Speaker Out), and then click OK to save the setting.
8. Click OK to exit Realtek HD Audio Manager.
2
Audio Features 2 - 7
Storage Devices, Mouse, & Audio
Mouse Driver
If you are using an external mouse your operating system may be
able to auto-configure
your mouse during its
installation or only enable its basic functions.
Be sure to check the
device’s user documentation for details.
2
Touchpad and Buttons/Mouse
The Touchpad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The Touchpad buttons function in
much the same way as a two-button mouse.
2 - 8 Touchpad and Buttons/Mouse
Storage Devices, Mouse, & Audio
TouchPad Scrolling
This computer model series may feature different
TouchPad versions.
These TouchPads may
differ in their vertical
scrolling function in most
scrollable windows.
Some TouchPads require
sliding the finger up and
down on the right of the
TouchPad to scroll the
window. Other versions
require tapping/holding
down the finger at the top
right or bottom right of the
TouchPad to scroll the
window.
Figure 2 - 5
Mouse Properties
Touchpad Configuration
Once you have installed the TouchPad driver (see “Touchpad” on page 4 - 8) you
can configure the functions from the Mouse control panel in Windows, or by d oubleclicking the TouchPad driver icon in the notification area of the taskbar in the
Desktop app. You may then configure the TouchPad tapping, buttons, scrolling,
pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.
2
Touchpad Configuration 2 - 9
Storage Devices, Mouse, & Audio
Show Video
You can get a clearer
view of the gestures involved by clicking the
Show Video option for
each gesture item.
Select the gesture (Pinch
Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Settings left tree menu
and click the Show Video
button to see the demonstration video.
For more details on any of
the gestures see the help
in the lower part of the
right menu window.
Figure 2 - 6
Mouse Properties -
Device Settings
2
Gestures and Device Settings
The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications.
You can configure the settings from the Device Settings tab in Mouse Properties:
1. Go to the
2. Click Mouse (Hardware and Sound).
3. Click Device Settings (tab) and click Settings.
4. Use the menu tree on the lef t to access the user configurable settings.
Control Panel
.
2 - 10 Touchpad Configuration
Storage Devices, Mouse, & Audio
Figure 2 - 7
Mouse Properties
(Disable Touchpad)
Disabling the Touchpad
If you need to disable the Touchpad for any reason (e.g. you may find that when using the computer’s internal keyboard you accidentally trigger the Touchpad when
resting your wrists or palms on it) you can do so by using Fn + F1 key combination.
You can also set the system to automatically disable the internal Touchpad when an
external USB point device (e.g a USB mouse) is attached.
1. Go to the Mouse Properties control panel.
2. Click to select Device Settings (tab).
3. Click to place a check in the “Disable internal pointing device when external
USB pointing device is attached” check box.
4. Click OK to save the setting.
2
Touchpad Configuration 2 - 11
Storage Devices, Mouse, & Audio
PalmCheck™
In order to improve
Clickpad/Touchpad
scrolling responsiveness when using onefinger scrolling, you can
adjust the PalmCheck™
slider towards “Minimum” as per your preference.
However bear in mind
that adjusting the slider
too far towards “Minimum” can turn off PalmCheck™ altogether.
Figure 2 - 8
PalmCheck™ Slider
2
PalmCheck™
The PalmCheck™ feature (Device Settings > Settings > Pointing > Sensitivity)
helps prevent operating the Clickpad/Touchpad by accident, by recognizing when
your palm is resting on it or brushing its surface while you are typing.
2 - 12 Touchpad Configuration
Storage Devices, Mouse, & Audio
Figure 2 - 9
Scrolling Gesture
Figure 2 - 10
Zooming Gesture
Scrolling
The Two-Finger scrolling feature works in most scrollable windows and allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel
in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and
slide them apart to zoom in, or closer together to zoom out.
2
Touchpad Configuration 2 - 13
Storage Devices, Mouse, & Audio
Figure 2 - 11
Rotating Gesture
Figure 2 - 12
Flick/Press
Gesture
2
Rotating
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another
finger near the middle of the TouchPad and slide it in a circular motion around the
stationary finger (clockwise or counterclockwise) to rotate the object.
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of
applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.
2 - 14 Touchpad Configuration
Chapter 3: Power Management
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
• The Power Sources
• Turning On the Computer
• Power Plans
• Power-Saving States
• Configuring the Power Buttons
• Battery Information
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
3
Overview 3 - 1
Power Management
Forced Off
If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the system to turn itself off.
3
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. Attach th e AC/DC adapter to the DC-in jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and connect the AC power cord to the AC/
DC adapter (make sure you use the adapter when first setting up the
computer, as to safeguard the computer during shipping, the battery will be locked
to not power the system until first connected to the AC/DC adapter).
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “Battery FAQ” on page 3 - 18).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 14.
3 - 2 The Power Sources
Turning On the Computer
Power Button as Stand by or Hibernate Button
You can use the OS’s “Power Options” control panel to set the power button to send the
system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring
the Power Buttons” on page 3 - 9 for details).
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options (Hardware and Sound) in the Windows control panel to configure
this feature.
Power Management
3
Turning On the Computer 3 - 3
Power Management
Figure 3 - 1
Shut Down/Restart
Charms Bar Desktop App Start Screen
Shutting the Computer Down
Note that you should always shut your computer down by choosing the Shut down
3
command as this will help prevent hard disk or system problems. Use the Shut down
or sign out item in the Context Menu (right-click the lower left corner of the screen
to bring up the menu).
You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If
you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep
to the Power Menu” on page 3 - 10.
3 - 4 Shutting the Computer Down
Power Plans
Resuming
Operation
See Table 3 - 1, on
page 3 - 11 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 2
Power Plan
Advanced Settings
The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Power Management
3
Power Plans3-5
Power Management
Figure 3 - 3
Power Plans
Click to Show/Hide
additional
power plans
3
Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
3 - 6 Power Plans
Loading...