Clevo P570WM User guide

Download

For Windows 8.1

V13.11.00(W81)

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©December 2013

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc ed radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interfer ence that may cause undesired operation of the

device.

III

Preface



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

ErP Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:

• Off Mode < 0.5W

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 -

240V, 50 - 60Hz DC Output 19.5V, 16.92A (330W) OR 20V, 15A (300W)minimum).

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive

heat or direct sunlight.

Do not leave it in a place where

foreign matter or moisture may

affect the system.

Don’t use or stor e the computer

in a humid environment.

Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he computer. Shut th e comp uter down pro per ly and don’t for ge t

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

5. Take care when using peripheral devices.

Use only approved brands of peripherals.

Do not disassemble the computer by yourself.

Unplug the power cord befor e attaching peripheral devices.

Perform routine maintenance on your computer.

VII

Preface



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).

You must also remove your battery in order to prevent accidentally turning the machine on. Before removing

the battery disconnect the AC/DC adapter from the computer.

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC ada pter may be design ed for inte rnational travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult

VIII

your service representative or local power company .

• The power adapter may have either a 2-pr ong or a 3-prong ground ed plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be su re to disconnect it by the plug head, not by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

Preface



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteri es may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

Cleaning



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

Preface



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -

ware and software. Make sure your “papers” are handy.

XII

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.

XIII

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your kne es, hips and elbows form approximately 90-degree angles when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.

XIV

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long ).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your service center.

Preface

XVI

Preface

Contents

Notice .............................................................................................................................................................I

FCC Statement ............................................................................................................................................III

FCC RF Radiation Exposure Statement: ....................................................................................................IV

ErP Off Mode Power Consumption Statement: ..........................................................................................IV

Instructions for Care and Operation ...........................................................................................................VI

Power Safety ............................................................................................................................................VIII

Polymer Battery Precautions ......................................................................................................................IX

Battery Precautions ......................................................................................................................................X

Cleaning ......................................................................................................................................................XI

Servicing .....................................................................................................................................................XI

Travel Considerations ............................................................................................................................... XII

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Model Differences .....................................................................................................................................1-3

Not Included ..............................................................................................................................................1-3

System Software ........................................................................................................................................1-4

RAID & AHCI Setup .................................................................................................................................1-4

XVII

Preface

System Startup ...........................................................................................................................................1-5

System Map: LCD Panel Open & Top View ............................................................................................1-6

LED Indicators ...........................................................................................................................................1-8

Touch Sensor Instant Keys ........................................................................................................................1-9

Keyboard ..................................................................................................................................................1-10

Keyboard Shortcuts .................................................................................................................................1-11

Keyboard LED .........................................................................................................................................1-12

Effects Buttons & Help ............................................................................................................................1-14

Function Keys & Visual Indicators .........................................................................................................1-15

Control Center .........................................................................................................................................1-16

System Map: Front & Rear Views ...........................................................................................................1-17

System Map: Right View .........................................................................................................................1-18

System Map: Left View ...........................................................................................................................1-19

System Map: Bottom View .....................................................................................................................1-21

Windows 8.1 Control Panel .....................................................................................................................1-22

Windows 8.1 Start Screen & Desktop .....................................................................................................1-24

Apps & Tiles ............................................................................................................................................1-25

Desktop Application ................................................................................................................................1-26

The Charms Bar .......................................................................................................................................1-27

Windows 8.1 Control Panel .....................................................................................................................1-29

Windows 8.1 Taskbar ..............................................................................................................................1-32

Video Features .........................................................................................................................................1-33

XVIII

Preface

Screen Resolution ....................................................................................................................................1-34

NVIDIA Control Panel ............................................................................................................................1-35

Catalyst Control Center ...........................................................................................................................1-36

Power Options .........................................................................................................................................1-37

Running Apps ..........................................................................................................................................1-38

Storage Devices, Mouse & Audio

Overview ....................................................................................................................................................2-1

Hard Disk Drive .........................................................................................................................................2-2

Optical Device ...........................................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-In-1 Card Reader .............................................................................................................................2-6

ExpressCard Slot .......................................................................................................................................2-7

Inserting and Removing ExpressCards ......................................................................................................2-7

Audio Features ...........................................................................................................................................2-8

Setup for 5.1 or 7.1 Surround Sound .........................................................................................................2-9

Setup for Audio Recording ......................................................................................................................2-11

Audio Notes for Fn + 5 ............................................................................................................................2-12

TouchPad and Buttons/Mouse .................................................................................................................2-13

Gestures and Device Settings ..................................................................................................................2-14

XIX

Preface

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

Battery ........................................................................................................................................................3-2

Turning On the Computer ..........................................................................................................................3-3

Shutting the Computer Down ....................................................................................................................3-4

Power Plans ...............................................................................................................................................3-5

Power-Saving States ..................................................................................................................................3-7

Sleep ..........................................................................................................................................................3-7

Hibernate ....................................................................................................................................................3-8

Shut down ..................................................................................................................................................3-8

Configuring the Power Buttons .................................................................................................................3-9

Resuming Operation ................................................................................................................................3-11

Power Conservation Modes .....................................................................................................................3-12

Battery Information .................................................................................................................................3-14

Battery Power ..........................................................................................................................................3-14

Conserving Battery Power .......................................................................................................................3-15

Battery Life ..............................................................................................................................................3-16

New Battery .............................................................................................................................................3-16

Recharging the Battery with the AC/DC Adapter ...................................................................................3-16

Proper handling of the Battery Pack ........................................................................................................3-17

Preface

Battery FAQ .............................................................................................................................................3-18

Multi GPU Configuration & Power .........................................................................................................3-22

Drivers & Utilities

RAID & AHCI Setup .................................................................................................................................4-1

What to Install ............................................................................................................................................4-1

Driver Installation ......................................................................................................................................4-2

Updating/Reinstalling Individual Drivers ..................................................................................................4-4

User Account Control ................................................................................................................................4-5

Windows Security Message .......................................................................................................................4-5

New Hardware Found ................................................................................................................................4-5

Driver Installation Procedure .....................................................................................................................4-6

Chipset .......................................................................................................................................................4-6

NVIDIA Video (VGA) ..............................................................................................................................4-6

AMD Video (VGA) ...................................................................................................................................4-6

LAN ...........................................................................................................................................................4-6

Card Reader ...............................................................................................................................................4-7

TouchPad ...................................................................................................................................................4-7

Hot Key ......................................................................................................................................................4-7

MEI Driver .................................................................................................................................................4-7

Audio .........................................................................................................................................................4-7

Optional Drivers ........................................................................................................................................4-9

XXI

Preface

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Power-On Self Test (POST) ...............................................................................................................5-2

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

The Setup Utility ........................................................................................................................................5-4

Entering Setup ...........................................................................................................................................5-4

Setup Screens .............................................................................................................................................5-5

Main Menu .................................................................................................................................................5-6

System Time & Date (Main Menu) ...........................................................................................................5-6

SATA Port # (Main Menu) ........................................................................................................................5-7

System/Extended Memory (Main Menu) ..................................................................................................5-7

BIOS Revision/ KBC/EC firmware Revision / VGA Card etc. (Main Menu) ..........................................5-7

Advanced Menu .........................................................................................................................................5-8

Advanced Chipset Control (Advanced Menu) ..........................................................................................5-8

Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-9

Intel(R) Rapid Storage Technology (Advanced Menu) .............................................................................5-9

SATA Mode (Advanced Menu) ................................................................................................................5-9

Boot Logo (Advanced Menu) ..................................................................................................................5-10

Power On Boot Beep (Advanced Menu) .................................................................................................5-10

Battery Low Alarm Beep (Advanced Menu) ...........................................................................................5-10

XXII

Preface

Security Menu ..........................................................................................................................................5-11

Set Supervisor Password (Security Menu) ..............................................................................................5-11

Set User Password (Security Menu) ........................................................................................................5-12

Password on boot (Security Menu) ..........................................................................................................5-12

Secure Boot Control (Security Menu) .....................................................................................................5-12

Trusted Computing (Security Menu) .......................................................................................................5-13

TPM State (Security Menu > TPM Support Enabled) .............................................................................5-14

Pending TPM operation (Security Menu > TPM Support & TPM State Enabled) .................................5-15

Boot Menu ...............................................................................................................................................5-16

Boot Option Priorities (Boot Menu) ........................................................................................................5-17

OS Select (Boot Menu) ............................................................................................................................5-17

UEFI Boot (Boot Menu > OS Select) ......................................................................................................5-17

Save & Exit Menu ...................................................................................................................................5-18

Upgrading The Computer

Overview ....................................................................................................................................................6-1

When Not to Upgrade ................................................................................................................................6-2

Removing the Battery ................................................................................................................................6-4

Upgrading the Optical (CD/DVD) Device ................................................................................................6-5

Upgrading the Hard Disk Drive(s) ............................................................................................................6-6

Upgrading the System Memory (RAM) ..................................................................................................6-12

Upgrading the Video Card .......................................................................................................................6-25

XXIII

Preface

Modules

Overview ....................................................................................................................................................7-1

Setting Up SATA RAID or AHCI Mode ..................................................................................................7-2

AHCI Mode ...............................................................................................................................................7-2

RAID ..........................................................................................................................................................7-2

Intel® Rapid Storage Technology Application .........................................................................................7-2

RAID Setup (Windows 8.1) ......................................................................................................................7-3

SATA RAID Setup Procedure (Windows 8.1) ..........................................................................................7-5

IRST Driver Installation ..........................................................................................................................7-11

Deleting a RAID (Windows 8.1) .............................................................................................................7-12

PC Camera Module ..................................................................................................................................7-13

PC Camera Audio Setup .........................................................................................................................7-14

Camera App .............................................................................................................................................7-15

Camera Options .......................................................................................................................................7-16

Taking Pictures/Capturing Video ............................................................................................................7-17

Camera Roll .............................................................................................................................................7-18

Wireless LAN Module .............................................................................................................................7-22

3rd Party 802.11b/g/n WLAN Combo Driver Installation ......................................................................7-23

Intel® WLAN Driver Installation ............................................................................................................7-24

Qualcomm Atheros WLAN Combo Driver Installation ..........................................................................7-25

Qualcomm Atheros Killer Network Manager .........................................................................................7-26

WLAN Configuration in Windows .........................................................................................................7-32

XXIV

Preface

Security Modules (Fingerprint & TPM) ..................................................................................................7-35

Fingerprint Reader Module ......................................................................................................................7-36

AuthenTec Fingerprint Reader Driver Installation ..................................................................................7-37

BioExcess Fingerprint Reader Driver Installation ...................................................................................7-37

Fingerprint Module Configuration ..........................................................................................................7-38

Bluetooth Module ....................................................................................................................................7-40

3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-41

Intel Bluetooth Combo Driver Installation ..............................................................................................7-41

Bluetooth Configuration in Windows ......................................................................................................7-42

Trusted Platform Module .........................................................................................................................7-45

Enabling & Activating TPM ....................................................................................................................7-46

Trusted Platform Module (TPM) Driver Installation ..............................................................................7-48

Initializing TPM .......................................................................................................................................7-49

Infineon Security Platform Settings Tool ................................................................................................7-51

Sound Blaster Audio ................................................................................................................................7-59

Sound Blaster X-Fi MB-3 Audio AP Installation ....................................................................................7-59

Intel® Rapid Storage Technology ...........................................................................................................7-68

IRST Driver Installation ..........................................................................................................................7-68

Intel® Rapid Storage Technology for RAID Systems ............................................................................7-69

RAID Volume Data Verification and Repair ..........................................................................................7-71

Replacing and Reverting Recovery and Master Volumes .......................................................................7-71

XXV

Preface

Troubleshooting

Overview ....................................................................................................................................................8-1

Basic Hints and Tips ..................................................................................................................................8-2

Backup and General Maintenance .............................................................................................................8-3

Viruses .......................................................................................................................................................8-4

Upgrading and Adding New Hardware/Software ......................................................................................8-5

Problems & Possible Solutions ..................................................................................................................8-7

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Ports and Jacks ..........................................................................................................................................A-2

Card Reader ..............................................................................................................................................A-2

DC-In Jack ................................................................................................................................................A-2

DisplayPort ...............................................................................................................................................A-2

DVI-Out Port ............................................................................................................................................A-2

e-SATA/Powered USB 3.0 Port ...............................................................................................................A-3

HDMI-Out Port .........................................................................................................................................A-3

Headphone-Out Jack .................................................................................................................................A-3

Line-In Jack ..............................................................................................................................................A-4

Microphone-In Jack ..................................................................................................................................A-4

Mini-IEEE 1394 Port ................................................................................................................................A-4

RJ-45 LAN Jack .......................................................................................................................................A-4

XXVI

Preface

S/PDIF-Out Jack .......................................................................................................................................A-4

Security Lock Slot ....................................................................................................................................A-5

USB 2.0/1.1 Ports* ...................................................................................................................................A-5

USB 3.0 Port .............................................................................................................................................A-5

Control Center

Overview ...................................................................................................................................................B-1

NVIDIA Video Driver Controls

NVIDIA Video Driver Installation ...........................................................................................................C-1

NVIDIA Control Panel .............................................................................................................................C-2

Display Devices ........................................................................................................................................C-5

Configuring an External Display (NVIDIA) ............................................................................................C-6

Extending the Display ...............................................................................................................................C-7

Multiple Display Connection to HDMI-Out Port & DisplayPort ...........................................................C-10

Attaching Other Displays - Devices (Charms Bar) ................................................................................C-11

Attaching Other Displays .......................................................................................................................C-12

NVIDIA® SLI Multi GPU Configuration ..............................................................................................C-14

NVIDIA® SLI Multi GPU Configuration & Power ..............................................................................C-15

Manage 3D Settings ................................................................................................................................C-16

Adjust Video Settings .............................................................................................................................C-17

HDMI Audio Configuration ...................................................................................................................C-18

Audio Setup for HDMI ...........................................................................................................................C-19

XXVII

Preface

HDMI Notes ...........................................................................................................................................C-21

HDMI Video Configuration ...................................................................................................................C-21

HDCP Status ...........................................................................................................................................C-22

NVIDIA 3D Shutter Glasses Kit ............................................................................................................C-23

Stereoscopic 3D Hardware Setup ...........................................................................................................C-24

Viewing Angles ......................................................................................................................................C-25

Set Up Stereoscopic 3D ..........................................................................................................................C-26

AMD Video Driver Controls

Video Driver Installation ..........................................................................................................................D-1

Video (VGA) ............................................................................................................................................D-1

Catalyst™ Control Center ........................................................................................................................D-2

Display Devices & Options ......................................................................................................................D-7

Configuring an External Display In the CCC............................................................................................D-8

Attaching Other Displays - Devices (Charms Bar) ................................................................................D-12

Configuring an External Display In Windows .......................................................................................D-13

AMD CrossFireX™ Multi GPU Configuration .....................................................................................D-16

AMD CrossFireX™ Multi GPU Configuration & Power.......................................................................D-17

HDMI Audio Configuration ...................................................................................................................D-18

Specifications

Processor ...................................................................................................................................................E-2

Core Logic ................................................................................................................................................E-2

XXVIII

Preface

Display ......................................................................................................................................................E-2

Memory .....................................................................................................................................................E-2

Video Adapter ...........................................................................................................................................E-2

BIOS .........................................................................................................................................................E-3

Storage ......................................................................................................................................................E-3

Audio ........................................................................................................................................................E-3

Keyboard & Pointing Device ....................................................................................................................E-4

Card Reader .............................................................................................................................................. E-4

Slots ..........................................................................................................................................................E-4

Interface ....................................................................................................................................................E-4

Communication .........................................................................................................................................E-4

Indicators ..................................................................................................................................................E-5

Security ..................................................................................................................................................... E-5

Operating System ......................................................................................................................................E-5

Design Feature ..........................................................................................................................................E-5

Power Management ..................................................................................................................................E-5

Power ........................................................................................................................................................E-5

Environmental Spec ..................................................................................................................................E-5

Physical Dimensions & Weight ................................................................................................................E-5

XXIX

Preface

XXX

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk, optical device, Multi-In-1 card reader), Game Keys, TouchPad & Mouse & Audio Features.

• Chapter 3 The computer’s power management options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s RAID, PC Camera, Wireless LAN, Fingerprint and Bluetooth & WLAN Combo modules (some of which may be optional depending on your purchase configu- ration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.

• Appendix B Information on the Control Center.

• Appendix C Information on the NVIDIA Video driver controls.

• Appendix D Information on the AMD Video driver controls.

• Appendix E The computer’s specification.

Overview 1 - 1



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”

on page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4

- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your

system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers

& Utilities” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Interface (Ports & Jacks)” on page A - 1 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Model Differences

This notebook series includes two different model types (only Model B computers support 3D). Note that your model may appear slightly different from those pictured in this manual.

Not Included

Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.

Overview 1 - 3



Windows Versions

Note that the information included on the following pages is for Windows 8.1 only. The Windows 7/8 interface is different in appearance an d in methods of navigation, and a separate manual is provided

on the Device Drivers & Manual Disc for Windows 7/8.

Windows OS

In order to run Windows 7/8/8.1 (32 Bit) without limitations or decreased performance, your computer requires a minimum

1GB of system memory (RAM), however if you are running Windows 7/8/8.1 (64 bit) your computer requires a minimum 2GB of system memory (RAM).

Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 o perating system is supported.

Note: In order to run Windows without limitations or decreased performance, your computer requires a mini- mum 1GB of system memory (RAM).

RAID & AHCI Setup

Note that setting up a RAID, or AHCI mode, needs to be done prior to installing the Windows OS (see “Setting

Up SATA RAID or AHCI Mode” on page 7 - 2).

1 - 4 Overview

Quick Start Guide



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command in Windows (see page 1 - 37). This will help prevent hard disk or system problems.



NVIDIA® SLI or AMD™ CrossfireX Multi GPU Configuration & Power Note that where two video adapters are installed in an SLI or a Cross-

fire configuration, dual power adapters connected to a power converter box are required to power the system (see pages C - 15 & D - 17).

Single video adapter configurations only require a single power adapter.

135°

System Startup

1. Remove all packing materials, and place the c omp ut er on a stable surface.

2. Securely attach any peripherals you want to use with the notebook (e.g. keyboa rd and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter.

4. Use one hand to raise the

the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lif t the computer by the lid/LCD).

5. Raise the lid/LCD to a comfortable viewing angle, and press the power button.

lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);

use

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD

System Startup 1 - 5

Figure 1 - 2

LCD Panel Open

& Top View

1. Built-In PC Camera

2. Built-In Microphone

3. PC Camera LED

4. LCD

5. LED Status Indicators

6. Touch Sensor Instant Keys

7. Speakers

8. 3D IR Emitter (Model B Only)

9. Power Button

10.Keyboard

11. TouchPad and Buttons

12.Fingerprint Reader Module

13. LCD Panel Color LED



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is usually prohibited. Make sure any wireless modules are OFF if you are using the computer aboard aircraft.

Use the appropriate function key combination to toggle power to any wireless modules, and check the indicators to see if any modules are powered on or not (see Table 1 -

2, on page 1 - 9).

7 7

Quick Start Guide

1 - 6 System Map: LCD Panel Open & Top View

System Map: LCD Panel Open & Top View

Quick Start Guide

Speaker Note

Note that the speaker area is covered by a protective mylar film on shipping. In order to prevent any impairment to audio quality, this film should be removed when the system is ready for use.

Figure 1 - 3 - Speaker Area

System Map: LCD Panel Open & Top View 1 - 7

Quick Start Guide

LED Indicators

The two sets of LED indicators (LED Status Indicators and LED Power Indicators) display helpful information about the current status of the computer.

Icon Color Description Icon Color Description

Blinking

Blue

HDD/ODD Activity Orange DC Power is Plugged In

Number Lock is Activated Green The Computer is On

Blinking Green The Computer is In Sleep Mode

Caps Lock is Activated Blinking Orange* The Powered USB Port is On*

Orange The Battery is Charging

Scroll Lock is Activated

Table 1 - 1 - LED Status Indicators

Blinking Orange

Green The Battery is Fully Charged

The Battery has Reached Critically

Low Power Status

*Note: The powered USB 3.0/e-SATA port (see Figure 1 - 9 on pa ge 1 - 19) may be toggled on /off by means of the Fn + Power Button key combination (press for around 1 to 2 seconds to toggle). When the powered USB port is on it will

supply power (for charging devices only, not for operating devices) when the system is off but still powered by the AC/ DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with certain devices).

1 - 8 System Map: LCD Panel Open & Top View

Quick Start Guide

Touch Sensor Instant Keys

Press the Touch Sensor Instant Keys on the computer to toggle the appropriate function on/off. When a module is powered on the appropriate icon will be highlighted blue.

Icon Description

Mute Toggle

Bluetooth Module - Installed

Indicates the (optional) Bluetooth Module is Installed

(this is not a power on/off indicator in Windows 8.1)

Wireless LAN Module - Installed

Indicates the (optional) WLAN Module is Installed

(this is not a power on/off indicator in Windows 8.1)

PC Camera Module Power Toggle

Volume Control (Press and hold your finger at either end

to adjust the system volume)

/ of the volume control

Table 1 - 2 - Touch Sensor Instant Keys

Note that you can also use the function key combinations for all of the functions above (see page 1 - 14).

Touch Sensor Instant Keys 1 - 9



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.

Num Lk & Scr Lk

Hold down the Fn Key and Scr Lk/Num Lk to enable scroll lock/number lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

ScrLk Key

Fn Key

Keypad

Game Control Keys

NumLk Key

Windows Logo Key



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Quick Start Guide

Keyboard

The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See

Table 1 - 6, on page 1 - 15 for full function key combination details.

Figure 1 - 4 - Keyboard

1 - 10 Keyboard

Keyboard Shortcuts



Windows Logo

Keyboard Shortcut

Use the Windows logo key + D key com- bination to switch from the Start screen to the Windows Desktop.

Menu/Application

Keyboard Shortcut

When the Desktop app is running you can use the Menu/Application key on the keyboard to act as a mouse right-click. In the Start screen this function is useful to quickly display Cus- tomize Apps.

The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in

Windows Logo

Key +

Tap Winkey

CDisplay Charms menu D Switch to the Windows Desktop and toggle show Desktop

F Display file Search

I Open the Settings charm

K Open the Connect charm

L Lock the computer and display the Lock screen P Display the Second Screen menu (see Figure 1 - 23 on page 1 - 33) R Switch to the Windows Desktop and display the Run dialog box Z Access the Customize Bar (see Figure 1 - 14 on page 1 - 25)

Windows 8.1

Description

Toggle between the Start screen and the foremost running app or the

Windows Desktop

Switch to the Windows desktop and launch Windows Explorer with

Computer displayed

Table 1 - 3 - Keyboard Shortcuts

Quick Start Guide

Keyboard 1 - 11

2 3

Quick Start Guide

Keyboard LED

Press Fn plus the key to toggle the keyboard LED on/off. The keyboard LED may be configured using the Fn + key combination outlined in the table below. In addition press Fn plus the keyboard backlight application to configure the settings (see overleaf).

Keyboard LED Function key Combinations

key to launch the

Fn +

(for Custom Mode only - see Table 1 - 5, on page 1 - 14)

Launch the Keyboard Backlight Application

Toggle the Keyboard Backlight On/Off

Keyboard LED Illumination Decrease

Keyboard LED Illumination Increase

Table 1 - 4 - Keyboard LEDs

1 - 12 Keyboard LED

Quick Start Guide

Help Button

Keyboard Sections

Color Swatches

Effects Buttons

Keyboard Backlight Application

The keyboard Backlight application can be accessed by pressing the Fn plus key. Click the Help button

in the application to display the configuration keys.

• Click the Custom button to display the three sections of the keyboard which may be configured.

• Click a section of the keyboard and the color buttons will be displayed.

• Click a color swatch to apply the color to the selected section when not overridden by any effect applied.

• Click on any of the effect buttons to apply random colors, wave or flashing effects etc (see over).

Figure 1 - 5 - Keyboard Backlight Application

Keyboard LED 1 - 13



Illumination Keys

Note that the keyboard illumination (increase/decrease) keys may be used to configure the keyboard LED in Cus-

tom Mode only.

Quick Start Guide

Effects Buttons & Help

LED Effects Buttons

1 - 14 Keyboard LED

Random Color

Dancing Effect

Tempo Beat

Flashing

Custom Mode - Display & Configure

Table 1 - 5 - LED Effects Buttons & Help

Up/Down Wave

Breathing (All Colors)

Cycle (Colors as Selected in RGB)

Keyboard Sections & Colors

Quick Start Guide

Function Keys & Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed (see “Hot Key” on page 4 - 7).

Keys Function/Visual Indicators Keys Function/Visual Indicators

Fn + ~ Play/Pause (in Audio/Video Programs) Fn + Esc Control Center Toggle (see over)

Fn + F1 Touchpad Toggle Fn + F8/F9 Brightness Decrease/Increase

Fn + F2

Fn + F3 Mute Toggle Fn + F11

Fn + F4 Sleep Toggle Fn + F12

Fn + F5/F6 Volume Decrease/Increase

Fn + F7 Display Toggle

Fn + 1

(Press a key to or use Touchpad to turn on)

Fan Control Togg le - Toggle between Auto-

Turn LCD Backlight Off

matic Fan Control / Full Power

Fn + F10

Fn + Power

Button

Fn +

Fn + 5

Table 1 - 6 - Function Keys & Visual Indicators

PC Camera Power

Toggle

WLAN Module

Power Toggle

Bluetooth Module

Power Toggle

Powered USB 3.0 Port Power Toggle

(press for around 1 to 2 seconds to toggle)

Keyboard LED Toggle (see page 1 - 11)

Audio Toggle - Toggle betw een Stereo and

5.1 Surround Sound Modes (see page 2 - 12)

Keyboard LED 1 - 15



Control Center

Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.

Click on the power conservation modes to switch between Performance, Balanced or Energy Star modes. To remove the Power Conservation Modes screen just click in a blank area of the icon or press a key on the keyboard.

Click on the buttons (or just click and hold the mouse button) to adjust the slider for Brightness/Volume.

Click on Display Switch and click to choose a display mode from the menu.

Quick Start Guide

Control Center

When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch

Pad on/off (see Appendix B for full details).

in the notification area of the taskbar to toggle the Control Center on/off. The Con-

1 - 16 Control Center

Figure 1 - 6 - Control Center

System Map: Front & Rear Views

Figure 1 - 7

Front & Rear Views

LED Power Indicators

2. Express Card Slot

3. Multi-In-1 Card Reader

4. DC-In Jack

See Appendix A for a more detailed description of the ports & jacks etc.



ExpressCard Slot

The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.

Multi-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

Quick Start Guide

System Map: Front & Rear Views 1 - 17

Figure 1 - 8

Right View

1. Line-In Jack

2. S/PDIF-Out Jack

3. Microphone-In Jack

4. Headphone-Out Jack

5. 2 * USB 2.0 Ports

6. Sub Woofer

7. Security Lock Slot

See Appendix A for a more detailed description of the ports & jacks etc.



USB Ports

Note that the connections to the USB ports only fit one way, do not force them. USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

Quick Start Guide

System Map: Right View

1 - 18 System Map: Right View

System Map: Left View

Figure 1 - 9

Left View

1. DVI-Out Port

2. RJ-45 LAN Jack

3. HDMI-Out Port

4. Display Port

5. 2 * USB 3.0 Ports

6. Combined eSATA/ Powered USB 3.0 Port

7. Mini-IEEE 1394b Port

8. Optical Device Drive Bay

See Appendix A for a more detailed description of the ports & jacks etc.



Mini-IEEE 1394b Port

The Mini-IEEE 1394 port only supports SELF POW-

ERED IEEE 1394 devices.



HDMI Port

Note that the HDMI Port supports video and audio signals to attached exte rnal displays. Note that Sound Blaster Audio will be disabled when you are connecting to an external display through an HDMI connection (see page 7 - 67).

USB 3.0 Ports & USB Port Power

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. The powered USB 3.0 /e-SATA port can supply power (for charging devices only, not

for operating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level a bove 20% (this may not work with certain devices). Toggle power to this port by using Fn + power but-

ton (press for around 1 to 2 seconds to toggle).

Quick Start Guide

System Map: Left View 1 - 19



Disk Eject Warning

Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.

CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”.



Changing DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click th e +

next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.

DVD region detection is device dependent, not OSdependent. You can select your module’s region code 5 times. The fifth selection is pe rmanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Quick Start Guide

1 - 20 System Map: Left View

System Map: Bottom View

Figure 1 - 10

Bottom View

1. Fan Outlet/Intake

2. Component Bay Cover

3. Battery (HDD Bay located under the battery)

4. HDD Bay



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions.

1 1

Quick Start Guide

System Map: Bottom View 1 - 21



Windows Versions

Note that the information included on the following pages is for Windows 8.1 only.

The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is provided on the De-

vice Drivers & Manual Disc with reference to

Windows 8.

Move the mouse to the bottom left

Start ScreenDesktop app

of the screen and right-click to access the menu.

Quick Start Guide

Windows 8.1 Control Panel

Throughout this manual you will see an instruction to open the Control Panel. R

ight-click the lower left hot corner to bring up the context menu (or use the Win-

dows Logo Key + X key combination)

Desktop app or Start screen.

and select Control Panel in both the

1 - 22 Windows 8.1 Control Panel

Figure 1 - 11 - Windows Context Menu

Right-click the Start button in the Desktop app (or use the Windows Logo Key



Display Most

Recently Used

Apps

If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app.

To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list.

Move the mouse to the bottom left of the screen

and right-click the Start button to access the menu.

+ X key combination) to bring up an advanced context menu of useful features

such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.

Figure 1 - 12 - Advanced Context Menu (Right-Click Start Button)

Quick Start Guide

Windows 8.1 Control Panel 1 - 23

Desktop App

Quick Start Guide

Windows 8.1 Start Screen & Desktop

The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking

the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps.

Figure 1 - 13 - Windows Start Screen

1 - 24 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Click the arrow at the bottom of the screen to access All Apps

Apps & Tiles

The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.

Accessing Pining/Unpinning All Apps

You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the Customize icon. Click the Customize icon to display all the installed

applications etc. Right-click any icon to bring up the menu at the bottom of the screen and you can then click the appropriate icon to pin the App to (or unpin from) the Start screen, or to the taskbar in the Desktop applica- tion (you can also open the app in a new window, run as administrator or open the file location).

Figure 1 - 14 - Customize Apps

Windows 8.1 Start Screen & Desktop 1 - 25

Move the mouse to the bottom left of the screen and click to switch back to the Start screen.

Quick Start Guide

Desktop Application

When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click.

When you move to the lower left hot corner in the Start screen it will take you back to your most recently used app (if one is running).

Figure 1 - 15 - Desktop

1 - 26 Windows 8.1 Start Screen & Desktop

The Charms Bar

Move the mouse over a Charms Bar icon to activate the menu

Move the mouse to the top/lower right icons to activate the Charms Bar

The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of

the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.

Quick Start Guide

Figure 1 - 16 - Start Screen with Charms Bar

Windows 8.1 Start Screen & Desktop 1 - 27



Charms Bar - TouchPad Access

To quick access the Charms Bar using the TouchPad:

1. Place your finger off the TouchPad (slightly to the right of the pad resting on the computer).

2. Move your finger across to the left on to the TouchPad.

3. The Charms Bar will then pop-up.

Quick Start Guide

Charms Bar Items

• Search : You can search for any file, application, Apps and control panel settings with instantaneous

results.

•Share : This button is used to share information with people via mail or social networks.

•Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or click-

ing the bottom left of the screen).

• Devices : Click this button to change connected peripheral device settings e.g. an external display.

• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).

Figure 1 - 17 - Settings Menu

1 - 28 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Windows 8.1 Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8.1.

•Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.

Figure 1 - 18 - Search (Control Panel)

• Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the top menu and select Open Control Panel from the ribbon.

Figure 1 - 19 - Open Control Panel (Computer)

Windows 8.1 Control Panel 1 - 29

Quick Start Guide

• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu.

Figure 1 - 20 - Settings Charms Bar (Desktop App Only)

• Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System).

Figure 1 - 21 - All Apps - Control Panel

1 - 30 Windows 8.1 Control Panel

Quick Start Guide



Keyboard Shortcut to Control Panel

You can also use keyboard shortcuts to access the Contro l Pa nel. Press th e Win dows logo key an d X to b ring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.

• Right-c lick the Start button to bring up the menu and select Control Panel (see Figure 1 - 12 on page 1

- 23).

Windows 8.1 Control Panel 1 - 31

Quick Start Guide

Windows 8.1 Taskbar

In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar is accessed from the Desktop application; if you are in the Start

screen you will need to switch to the Desktop. The taskbar is displayed at the bottom of the Desktop screen, and you can see the notification area (system

tray) of the taskbar in the bottom right of the screen. Some of the control panels and applications referred to during the course of this manual can be accessed from here.

Figure 1 - 22 - Desktop Taskbar & Notification Area (System Tray)

You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing

Pining/Unpinning All Apps” on page 1 - 25).

1 - 32 Windows 8.1 Control Panel

Quick Start Guide



NVIDIA/AMD Video Driver Controls

More detailed video controls are provided by the

NVIDIA Control Panel or Catalyst Control Center. For more detailed information see “NVIDIA

Control Panel” on page 1 - 35/“Catalyst Control Center” on page 1 - 36 a nd Appendix C

or Ap-

pendix D.

Video Features

This computer features two different (either AMD or NVIDIA) video options. You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows when running the Desktop app (see “Desktop Application” on page 1 - 26 and Appendix C/Appendix D). It is also possible to quickly configure external displays from the Devices menu item in the Charms Bar (see

“The Charms Bar” on page 1 - 27).

To Configure Displays from Devices (Charms Bar):

1. Attach your display to the appropriate port, and turn it on.

2. Go the Charms Bar, select Devices.

3. Click Project (you may need to click Second Screen).

4. Click on one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen

only.

Figure 1 - 23 - Devices (Project)

Video Features 1 - 33



Video Options

Note that card types, specifications and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported.

Quick Start Guide

Screen Resolution

1 - 34 Video Features

Figure 1 - 24 - Screen Resolution

NVIDIA Control Panel

You can access the NVIDIA Control Panel as follows:

Quick Start Guide

1. Go to the

2. Click NVIDIA Control Panel (Figure 1 - 25) - In the Appearances and Personalization category.

3. See “NVIDIA Video Driver Controls” on page C - 1 for full details on control panels etc.

4. You can also access the control panel by right-clicking the desktop and selecting NVIDIA Control Panel .

Windows Control Panel

Figure 1 - 25 - NVIDIA Control Panel

Video Features 1 - 35

Right-Click for Menu

Quick Start Guide

Catalyst Control Center

You can access the CatalystTM Control Center as follows:

1. Right-click the desktop and select Catalyst Control Center (Figure 1 - 26).

2. Double-click (or right-click the icon and select Catalyst Control Center) the icon (Figure 1 - 26) in the

Windows system tray notification area (make sure “Enable System Tray Menu” is clicked in Preferences).

3. See “AMD Video Driver Controls” on page D - 1 for full details on control panels etc.

Figure 1 - 26 - Catalyst Control Center Access

1 - 36 Video Features

Quick Start Guide

Charms Bar Desktop App Start Screen

Power Options

Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set- tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc.

Shut Down, Restart or Sleep (Charms Bar)

1. Go to the Charms Bar and click Settings.

2. Click Power .

3. Select Sleep, Shut Down or Restart.

Figure 1 - 27 - Shut Down/Restart

Power Options 1 - 37



Screen Resolution for Apps

(Windows 8/8.1)

The minimum resolution in which Apps will run is 1024x768. The minimum resolution required to support a ll the features of

Windows 8 (including multitasking with snap) is 1366x768. These specs are the minimum screen resolution that supports

all the features of Windows 8.1 on a useful physical size.

Quick Start Guide

Running Apps

To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements.

Screen Resolution Settings

1. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).

2. Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to

make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).

1 - 38 Running Apps

Figure 1 - 28 - Screen Resolution

Quick Start Guide

User Account Control Settings

If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below.

1. Open the Control Panel.

2. Click on User Accounts and then click on Change User Account Control settings (or click System and

Security and click Change User Account Control Settings under Action Center).

3. If the slider is in the Never notify position, then the UAC is disabled.

4. To enable or turn on the UAC, move the slider to Always notif y or Notify me when apps try to make changes

to my computer (default) position, and then click OK.

Figure 1 - 29 - User Account Control

Running Apps 1 - 39

Quick Start Guide

1 - 40

Storage Devices, Mouse & Audio

Chapter 2: Storage Devices, Mouse & Audio

Overview

Read this chapter to learn more about the following main features and components of the computer:

•Hard Disk Drive

• Optical Device

• Multi-In-1 Card Reader

• ExpressCard Slot

• Audio Features

• TouchPad and Buttons/Mouse

Overview 2 - 1

Storage Devices, Mouse & Audio



Power Safety

Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.

Figure 2 - 1

Hard Disk Bay

HDD Bay

2 - 2 Hard Disk Drive

Hard Disk Drive

The hard disk drive(s) is(are) used to store your data in the computer. The hard disk(s) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. The primary hard disk bay is accessible from the bottom of your computer as seen below.

The computer can accommodate up to three hard disks (two in the primary bay, and one under the battery ), and these may be configured in RAID, AHCI or IDE modes. Further details on removing and inserting the hard disk are available in “Up-

grading the Hard Disk Drive(s)” on page 6 - 6 and.

Storage Devices, Mouse & Audio



Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Win- dows. Click the Volume icon on the taskbar to check the setting.

Peripherals must be connected before you turn on the system.

Figure 2 - 2

Optical Device

123

Optical Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page E - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 16).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.

Optical Device 2 - 3

Storage Devices, Mouse & Audio



CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.

2 - 4 Optical Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Storage Devices, Mouse & Audio

Table 2 - 1

DVD Regional Coding

DVD Regional Codes

To change the DVD regional codes see “Changing DVD Regional Codes” on

page 1 - 20.

DVD Regional Coding

Region Geographical Location

1 USA, Canada

6China

Western Europe, Japan, South

Africa, Middle East & Egypt

South-East Asia, Taiwan, South

Korea, The Philippines, Indonesia,

Hong Kong

South & Central America, Mexico,

Australia, New Zealand

N Korea, Russia, Eastern Europe,

India & Most of Africa

Optical Device 2 - 5

Storage Devices, Mouse & Audio



Card Reader Cover

Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.

Figure 2 - 3

Right View

1. Card Reader

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

Multi-In-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “Card Reader” on page 4 - 7).

PC adapters may be required for some of these cards and are usually supplied with them.

2 - 6 Multi-In-1 Card Reader

Storage Devices, Mouse & Audio



ExpressCard

Slot Cover

Make sure you keep the cover in the ExpressCard slot when not in use. This will help prevent foreign objects and/ or dust getting in to the ExpressCard Slot.

Figure 2 - 4

Express Card Slot

1. ExpressCard Slot

ExpressCard Slot

The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards).

ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the ExpressCard driver (see “Card Reader” on page 4 - 7).

Inserting and Removing ExpressCards

• Align the ExpressCard with the slot and push it in until it locks into place.

• To remove an ExpressCard, simply press the card to eject it.

ExpressCard Slot 2 - 7

Storage Devices, Mouse & Audio



Volume Adjustment

The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the notification area to check the setting.

Headphone

Configuration

It is recommended that you set the Speaker

Configuration to Stereo (not to 5.1 or 7.1

Speaker) when listening through headphones in order to maximize audio quality.

Figure 2 - 5

Realtek Audio

Manager

Right-click the icon to access the menu above.

See “HDMI Audio Configuration” on page C - 18 for a description of the audio configuration when connecting an HDMI supported display device. See “Sound Blaster Audio” on page 7 - 59 for further audio information.

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination (see Table 1 - 6, on page 1 - 15).

2 - 8 Audio Features

Storage Devices, Mouse & Audio



Sound Blaster Audio &

HDMI

Note that the Sound Blaster audio effects do not apply to audio generated through an HDMI connection (see page 7 - 67.).

Fn + 5 Audio Toggle

The Fn + 5 key combination allows you to toggle the audio system between stereo and surround modes. The stereo mode will allow for a louder audio volume.

Note that if you have stereo mode enabled, and attempt to demo the speaker configuration, then the sound will only be enabled through the front and rear speakers (

see

page 2 - 12

Figure 2 - 6

Speaker

Configuration (7.1)



Auto Popup Dialog

You should enable the auto popup dialog to automatically detect when a device has been plugged-in. If disabled, double-click connector settings and click the box to enable the auto popup detection of plugged-in devices.

Connector Settings

Setup for 5.1 or 7.1 Surround Sound

To setup your system for 5.1 or 7.1 surround sound you will need to connect the audio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out jacks (note: the S/PDIF jack is used for 7.1 surround sound only).

1. Go to the

2. Click Realtek HD Audio Manager (or right-click the notification area icon and select Sound Manager).

3. Click Speakers (tab) and click Speaker Configuration (tab).

4. Select 5.1 or 7.1 Speaker from the Speaker Configuration pull-down menu.

Control Panel

and make sure you are in

Classic View

Audio Features 2 - 9

Storage Devices, Mouse & Audio

Figure 2 - 7

Connected Device

Auto Popup

Note: Side Speaker Out is required for 7.1 Surround only.

5. Plug the front speaker cables into the Headphone-Out Jack.

6. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows:

• Line-In Jack = Rear Speaker Out

• Microphone-In Jack = Center/Subwoofer Speaker Out

• S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)

7. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on

page 2 - 9).

8. Click to put a tick in the appropriate box according to the speaker plugged-in (e.g. Rear Speaker Out), and then click OK to save the setting.

9. Click OK to exit Realtek HD Audio Manager.

2 - 10 Audio Features

Storage Devices, Mouse & Audio

Figure 2 - 8

Realtek Audio

Manager -

Recording Setup

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:

1. Go to the

2. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).

3. Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust th e Recording Volume level to around 60, to obtain the optimum recording quality.

4. Click OK to close the control panel and save the settings.

Control Panel

and make sure you are in

Classic View

Audio Features 2 - 11

Storage Devices, Mouse & Audio

This computer features an Fn +5 key combination to toggle between standard audio and enhanced audio. Note the following which applies to software mode audio con- figuration through the computer’s internal speakers only (this does not apply to surround sound when configured through external Quadraphonic, 5.1 or 7.1 speaker systems):

•When the Speaker Configuration in Realtek HD Audio Manager is set to Stereo, you can use the Fn + 5 key combination to help increase the volume through the speakers.

•When the Speaker Configuration in Realtek HD Audio Manager is set to 5.1/

7.1 Speaker, the best audio configuration will be obtained with the combination of the Speaker Configuration set to Quadraphonic/5.1/7.1 Speaker, and the Sound Blaster AP turned ON.

Note that the Fn + 5 key combination is a toggle so you will need to press the key combination to test if the affect is applied or not.

Audio Notes for Fn + 5

2 - 12 Audio Features

Storage Devices, Mouse & Audio



TouchPad Scrolling

This computer model series may feature different TouchPad versions.

These TouchPads may differ in their vertical scrolling function in most scrollable windows.

Some TouchPads require sliding the finger up and down on the right of the TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the TouchPad to scroll the window.

Figure 2 - 9

Mouse Properties

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.

Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 7) you can configure the functions from the Mouse control panel in Windows, or by d oubleclicking the TouchPad driver icon in the notification area of the taskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. Use the Fn + F1 key combination to toggle the TouchPad on/off.

TouchPad and Buttons/Mouse 2 - 13

Storage Devices, Mouse & Audio



Show Video

You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu

and click the Show Video button to see the demonstration video.

For more details on any of the gestures see the help in the lower part of the right menu window.

Figure 2 - 10

Mouse Properties -

Device Settings

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the Touchpad to perform specific actions to manipulate documents, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Go to the

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (tab) and click Settings.

4. Use the menu tree on the lef t to access the user configurable settings.

Control Panel

2 - 14 TouchPad and Buttons/Mouse

Storage Devices, Mouse & Audio

Figure 2 - 11

SmartSense

Smart Sense

The Smart Sense feature helps prevent operating the Touchpad by accident, by recognizing when your palm is resting on it or brushing its surface while you are typing. You can adjust the sensitivity of Smart Sense by moving the slider towards Max (to help remove undesired pointer movement or clicks) or Off (if it misses intended motions or taps).

TouchPad and Buttons/Mouse 2 - 15

Storage Devices, Mouse & Audio

Figure 2 - 12

Scrolling Gesture



Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.

Figure 2 - 13

Zooming Gesture

Scrolling

The Two-Finger scrolling feature works in most scrollable windows an d allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality. Place two fingers on the TouchPad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.

2 - 16 TouchPad and Buttons/Mouse

Storage Devices, Mouse & Audio

Figure 2 - 14

Rotating Gesture

Figure 2 - 15

Flick/Press

Gesture

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The Three Fingers Down gesture may be used to launch user-selectable applications.

TouchPad and Buttons/Mouse 2 - 17

Storage Devices, Mouse & Audio

2-18

Chapter 3: Power Management



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows 7 OS.)

Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the LCD and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

• Multi GPU Configuration & Power

The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.

Overview 3 - 1

Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page E - 5).

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the

AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “Battery FAQ” on page 3 - 18).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Power Conservation Modes” on page 3 - 12.

3 - 2 The Power Sources

Turning On the Computer



Power Button as Stand by or Hibernate Button

You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring

the Power Buttons” on page 3 - 9 for details).

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.

Power Management

Turning On the Computer 3 - 3

Power Management

Figure 3 - 1

Shut Down/Restart

Charms Bar Desktop App Start Screen

Shutting the Computer Down

Note that you should always shut your computer down by choosing the Shut down

command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen

to bring up the menu). You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If

you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep

to the Power Menu” on page 3 - 10.

3 - 4 Shutting the Computer Down

Power Plans



Resuming Operation

See Table 3 - 1, on

page 3 - 11 for informa-

tion on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Figure 3 - 2

Power Plan

Advanced Settings

The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.

Power Management

Power Plans3-5

Power Management

Figure 3 - 3

Power Plans

Click to Show/Hide additional power plans

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

3 - 6 Power Plans

Power-Saving States



Wake On LAN

Support

Wake-On-LAN is only supported from Sleep or

Hibernate states in Windows.

If you require your computer to wake up from network activity in Windows then make sure that the computer is either in Sleep or Hiber- nate.

Wake-On-LAN is not supported from Shutdown states in Win- dows.

You can use power-saving states to stop the computer’s operation and restart where you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file( s) you last used.

If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.

To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power

Menu” on page 3 - 10.

Power Management

Power-Saving States 3 - 7

Power Management



Silent Mode

You can use Silent Mode to reduce power

consumption and fan noise. Use the Silent Mode Touch Sensor Instant Key to toggle this mode on/off.

On screen visual indicators and the Touch Sensor Instant Key will display the Silent Mode status (see

Table 1 - 2, on page 1 -

9).

Note Silent Mode may reduce computer performance.

Figure 3 - 4

Power Power

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the Power Menu see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.

3 - 8 Power-Saving States

Configuring the Power Buttons



Password Protection

It is recommended that you enable a password on wake up in order to protect your data.

However you can disable this setting from the Power Options menu by clicking Require a

password on wakeup

in the left menu, and selecting the options (click

Change settings that are currently unavailable).

Figure 3 - 5

Power Options

Define Power

Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.

Power Management

Configuring the Power Buttons 3 - 9

Power Management

Figure 3 - 6

Power Options

Define Power

Buttons - Shutdown

Settings

Adding Hibernate/Sleep to the Power Menu

Add Hibernate/Sleep to the Power Menu as follows.

1. Go to the Power Options (Hardware and Sound) control panel.

2. Click “Change settings that are currently unavailable” .

3. Click Choose what the power buttons do.

4. Click to put a tick in the Hibernate/Sleep box under Shutdown settings.

5. Click Save Changes and close the control panel.

3 - 10 Configuring the Power Buttons

Clevo P570WM User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Chapter 1: Quick Start Guide

Overview

Advanced Users

Beginners and Not-So-Advanced Users

Warning Boxes

Model Differences

Not Included

System Software

RAID & AHCI Setup

System Startup

System Map: LCD Panel Open & Top View

LED Indicators

Touch Sensor Instant Keys

Keyboard

Keyboard Shortcuts

Keyboard LED

Effects Buttons & Help

Function Keys & Visual Indicators

Control Center

System Map: Front & Rear Views

System Map: Right View

System Map: Left View

System Map: Bottom View

Windows 8.1 Control Panel

Windows 8.1 Start Screen & Desktop

Apps & Tiles

Desktop Application

The Charms Bar

Windows 8.1 Control Panel

Windows 8.1 Taskbar

Video Features

Screen Resolution

NVIDIA Control Panel

Catalyst Control Center

Power Options

Running Apps

Chapter 2: Storage Devices, Mouse & Audio

Overview

Hard Disk Drive

Optical Device

Loading Discs

Handling CDs or DVDs

DVD Regional Codes

Multi-In-1 Card Reader

Express Card Slot

Inserting and Removing ExpressCards

Audio Features

Setup for 5.1 or 7.1 Surround Sound

Setup for Audio Recording

Audio Notes for Fn + 5

TouchPad and Buttons/Mouse

Gestures and Device Settings

Chapter 3: Power Management

Overview

The Power Sources

AC/DC Adapter

Battery

Turning On the Computer

Shutting the Computer Down

Power Plans

Power-Saving States

Sleep

Hibernate

Shut down

Configuring the Power Buttons