V13.1.00
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©January 2013
Trademarks
Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
R&TTE Directive
This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.
This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.
EuP-Standby and Off Mode Power Consumption Statement:
The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode or standby mode:
• Standby Mode < 2W
• Off Mode < 1W
II
Preface
CE Marking
This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.
This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.
The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.
III
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienc ed radio/TV technician for help.
Operation is subject to the following two conditions:
1. This device may not cause interference.
And
2. This device must accept any interference, including interfer ence that may cause undesired operation of the
device.
IV
Preface
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
V
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit:
• Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 11.57A (
230W
11.8A (
) minimum.
This Computer’s Optical Device is a Laser Class 1 Product
VI
220W
) or DC Output 19.5V,
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place where
foreign matter or moisture may
affect the system.
Don’t use or store the computer
in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
VII
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until
you properly shut down all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
VIII
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
Power Safety
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines and
power cord).
You must also remove
your battery in order to
prevent accidentally
turning the machine
on. Before removing
the battery disconnect the AC/DC
adapter from the
computer.
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady , uninterru pted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
IX
Preface
Polymer Battery Precautions
Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.
• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha-
nism and is not a cause for concern.
• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-
ture environments, and do not store unused batteries for extended periods.
See also the general battery precautionary information overleaf for further information.
X
General Battery Precautions
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• If you do not use the battery for an extended period, then remove the battery from the computer for storage.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu al-
ified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteri es
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Preface
XI
Preface
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and
screw(s) before restoring power to the system.
Also note the following when the cover is removed:
• Hazardous moving parts.
• Keep away from moving fan blades.
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
XII
Preface
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -
ware and software. Make sure your “papers” are handy.
XIII
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XIV
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XV
Preface
Lighting
Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.
• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
• Rotate desktop background images every few days.
• Turn the monitor off when the system is not in use.
XVI
Preface
Contents
Notice .............................................................................................................................................................I
EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II
FCC Statement ............................................................................................................................................IV
FCC RF Radiation Exposure Statement: .....................................................................................................V
Instructions for Care and Operation ......................................................................................................... VII
Power Safety ...............................................................................................................................................IX
Polymer Battery Precautions .......................................................................................................................X
General Battery Precautions .......................................................................................................................XI
Cleaning .................................................................................................................................................... XII
Servicing ................................................................................................................................................... XII
Travel Considerations ..............................................................................................................................XIII
Quick Start Guide
Overview ....................................................................................................................................................1-1
Advanced Users .........................................................................................................................................1-2
Beginners and Not-So-Advanced Users ....................................................................................................1-2
Warning Boxes ..........................................................................................................................................1-2
Not Included ..............................................................................................................................................1-3
System Software ........................................................................................................................................1-4
System Startup ...........................................................................................................................................1-5
System Map: LCD Panel Open ..................................................................................................................1-6
XVII
Preface
LED Indicators ...........................................................................................................................................1-7
Keyboard ....................................................................................................................................................1-8
Function Keys & Visual Indicators ...........................................................................................................1-9
Control Center .........................................................................................................................................1-10
System Map: Front & Rear Views ...........................................................................................................1-11
System Map: Right View .........................................................................................................................1-12
System Map: Left View ...........................................................................................................................1-14
System Map: Bottom View .....................................................................................................................1-15
Windows 7 Start Menu & Control Panel .................................................................................................1-16
Video Features .........................................................................................................................................1-17
NVIDIA® Optimus™ Technology .........................................................................................................1-17
Power Options .........................................................................................................................................1-21
Storage Devices, Mouse, & Audio
Overview ....................................................................................................................................................2-1
Hard Disk Drive .........................................................................................................................................2-2
Optical Device ...........................................................................................................................................2-3
Loading Discs ............................................................................................................................................2-3
Handling CDs or DVDs .............................................................................................................................2-4
DVD Regional Codes ................................................................................................................................2-5
Multi-in-1 Card Reader ..............................................................................................................................2-6
Smart Card Reader .....................................................................................................................................2-7
XVIII
Preface
Audio Features ...........................................................................................................................................2-8
Setup for Audio Recording ........................................................................................................................2-9
Setup for 5.1 or 7.1 Surround Sound .......................................................................................................2-10
TouchPad and Buttons/Mouse .................................................................................................................2-12
Gestures and Device Settings ..................................................................................................................2-14
Power Management
Overview ....................................................................................................................................................3-1
The Power Sources ....................................................................................................................................3-2
AC/DC Adapter .........................................................................................................................................3-2
Battery ........................................................................................................................................................3-2
Turning On the Computer ..........................................................................................................................3-3
Power Plans ...............................................................................................................................................3-4
Power-Saving States ..................................................................................................................................3-6
Sleep ..........................................................................................................................................................3-6
Hibernate ....................................................................................................................................................3-7
Shut down ..................................................................................................................................................3-7
Configuring the Power Buttons .................................................................................................................3-8
Resuming Operation ..................................................................................................................................3-9
Power Conservation Modes .....................................................................................................................3-10
Battery Information .................................................................................................................................3-11
Conserving Battery Power .......................................................................................................................3-12
XIX
Preface
Battery Life ..............................................................................................................................................3-13
New Battery .............................................................................................................................................3-13
Recharging the Battery with the AC/DC Adapter ...................................................................................3-13
Proper handling of the Battery Pack ........................................................................................................3-14
Battery FAQ .............................................................................................................................................3-15
Drivers & Utilities
What to Install ............................................................................................................................................4-1
Module Driver Installation ........................................................................................................................4-1
Driver Installation ......................................................................................................................................4-2
Manual Driver Installation .........................................................................................................................4-4
Updating/Reinstalling Individual Drivers ..................................................................................................4-4
User Account Control ................................................................................................................................4-5
Windows Security Message .......................................................................................................................4-5
New Hardware Found ................................................................................................................................4-5
Driver Installation Procedure .....................................................................................................................4-6
Chipset .......................................................................................................................................................4-6
Video (VGA) .............................................................................................................................................4-6
NVIDIA Video (VGA) ..............................................................................................................................4-6
LAN ...........................................................................................................................................................4-7
Card Reader ...............................................................................................................................................4-7
TouchPad ...................................................................................................................................................4-7
XX
Preface
Hot Key ......................................................................................................................................................4-7
USB 3.0 ......................................................................................................................................................4-7
MEI Driver .................................................................................................................................................4-7
Audio .........................................................................................................................................................4-7
Windows Experience Index .......................................................................................................................4-9
Optional Drivers ........................................................................................................................................4-9
BIOS Utilities
Overview ....................................................................................................................................................5-1
The Power-On Self Test (POST) ...............................................................................................................5-2
Failing the POST .......................................................................................................................................5-3
Fatal Errors ................................................................................................................................................5-3
Non-Fatal Errors ........................................................................................................................................5-3
The Setup Utility ........................................................................................................................................5-4
Entering Setup ...........................................................................................................................................5-4
Setup Screens .............................................................................................................................................5-5
Main Menu .................................................................................................................................................5-6
System Time & Date (Main Menu) ...........................................................................................................5-6
SATA Port # (Main Menu) ........................................................................................................................5-7
System/Extended Memory (Main Menu) ..................................................................................................5-7
MB Series / BIOS Revision / KBC/EC firmware Revision / VGA Card (Main Menu) ...........................5-7
Advanced Menu .........................................................................................................................................5-8
XXI
Preface
Advanced Chipset Control (Advanced Menu) ..........................................................................................5-8
Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-9
VT-d (Advanced Menu > Advanced Chipset Control) ..............................................................................5-9
Intel Virtualization Technology (Advanced Menu > Advanced Chipset Control) ....................................5-9
Intel TXT (LT)Support (Advanced Menu > Advanced Chipset Control) .................................................5-9
Intel(R) Rapid Start Technology (Advanced Menu) ...............................................................................5-10
Intel Anti-Theft Technology (Advanced Menu) ......................................................................................5-10
SATA Mode (Advanced Menu) ..............................................................................................................5-10
Boot Logo (Advanced Menu) ..................................................................................................................5-11
Power On Boot Beep (Advanced Menu) .................................................................................................5-11
Battery Low Alarm Beep (Advanced Menu) ...........................................................................................5-11
Microphone, WLAN, Camera, Smart Card, Bluetooth & Fingerprint Settings (Advanced Menu) ........5-11
Security Menu ..........................................................................................................................................5-12
Set Supervisor Password (Security Menu) ..............................................................................................5-12
Password on boot: (Security Menu) ........................................................................................................5-13
TPM Configuration (Security Menu) ......................................................................................................5-13
Secure Boot (Security Menu) ..................................................................................................................5-14
Boot Menu ...............................................................................................................................................5-15
Boot Option Priorities (Boot Menu) ........................................................................................................5-16
OS Select (Boot Menu) ............................................................................................................................5-16
UEFI Boot (Boot Menu) ..........................................................................................................................5-16
Exit Menu ................................................................................................................................................5-17
XXII
Preface
Upgrading The Computer
Overview ....................................................................................................................................................6-1
When Not to Upgrade ................................................................................................................................6-2
Removing the Battery ................................................................................................................................6-3
Upgrading the Optical Device ...................................................................................................................6-4
Upgrading the Hard Disk Drive(s) ............................................................................................................6-5
Upgrading the System Memory (RAM) ..................................................................................................6-10
Replacing the Primary System Memory Modules ...................................................................................6-11
Modules
Overview ....................................................................................................................................................7-1
PC Camera Module ....................................................................................................................................7-2
PC Camera Driver Installation ...................................................................................................................7-3
PC Camera Audio Setup ............................................................................................................................7-4
Wireless LAN Module .............................................................................................................................7-10
Intel® WLAN Driver Installation ............................................................................................................7-11
Connecting to a Wireless Network in Windows 7 ...................................................................................7-14
Connecting to a Wireless Network Using Intel® PROSet Wireless .......................................................7-17
Intel® My WiFi Configuration ................................................................................................................7-19
Windows Mobility Center .......................................................................................................................7-28
Intel® Wireless Display Application .......................................................................................................7-29
Intel® WiDi Application Installation ......................................................................................................7-30
XXIII
Preface
Intel® Wireless Music Driver Installation ...............................................................................................7-30
Intel® WiDi Application Configuration ..................................................................................................7-31
Security Modules (Fingerprint & TPM) ..................................................................................................7-34
Fingerprint Reader Module ......................................................................................................................7-35
Fingerprint Reader Driver Installation .....................................................................................................7-36
User Enrollment .......................................................................................................................................7-37
Fingerprint Control Center Features ........................................................................................................7-42
Bluetooth Module ....................................................................................................................................7-43
Intel Bluetooth Combo Driver Installation ..............................................................................................7-44
Standard Bluetooth Configuration in Windows 7 ...................................................................................7-45
Intel® Rapid Storage Technology Driver ................................................................................................7-49
Intel® Rapid Start Technology Driver ....................................................................................................7-50
Intel® Rapid Start Technology Configuration ........................................................................................7-51
Intel® Rapid Start Technology Driver Installation .................................................................................7-57
Intel® vPro™ Technology ......................................................................................................................7-58
Accessing the Intel Management Engine ................................................................................................7-58
Intel® Management and Security Status .................................................................................................7-60
Trusted Platform Module .........................................................................................................................7-65
Enabling & Activating TPM ....................................................................................................................7-66
Trusted Platform Module (TPM) Driver Installation ..............................................................................7-68
Initializing TPM .......................................................................................................................................7-69
Infineon Security Platform Settings Tool ................................................................................................7-71
XXIV
Preface
Troubleshooting
Overview ....................................................................................................................................................8-1
Basic Hints and Tips ..................................................................................................................................8-2
Backup and General Maintenance .............................................................................................................8-3
Viruses .......................................................................................................................................................8-4
Upgrading and Adding New Hardware/Software ......................................................................................8-5
Problems & Possible Solutions ..................................................................................................................8-7
Bluetooth Connection Problems ..............................................................................................................8-16
Installing Windows 7 (pre Service Pack 1) for RAID Systems with Advanced Format Disks ...............8-20
Interface (Ports & Jacks)
Overview ...................................................................................................................................................A-1
Ports and Jacks ..........................................................................................................................................A-2
Card Reader ..............................................................................................................................................A-2
DB9 Serial Port .........................................................................................................................................A-2
DC-In Jack ................................................................................................................................................A-2
DisplayPort/Mini Display Port .................................................................................................................A-2
DVI-Out Port ............................................................................................................................................A-2
e-SATA / USB 3.0 Combo Port ...............................................................................................................A-3
Headphone-Out Jack .................................................................................................................................A-3
Line-In Jack ..............................................................................................................................................A-3
Microphone-In Jack ..................................................................................................................................A-3
XXV
Preface
Mini-IEEE 1394a Port ..............................................................................................................................A-3
RJ-45 LAN Jack .......................................................................................................................................A-4
S/PDIF-Out Jack .......................................................................................................................................A-4
Security Lock Slot ....................................................................................................................................A-4
Smart Card Reader ....................................................................................................................................A-4
USB 2.0/1.1 Ports .....................................................................................................................................A-5
USB 3.0 Port .............................................................................................................................................A-5
Powered USB 3.0 Port ..............................................................................................................................A-5
Control Center
Overview ...................................................................................................................................................B-1
Video Driver Controls
Video Driver Installation ..........................................................................................................................C-2
Intel Video (VGA) ....................................................................................................................................C-2
NVIDIA Video (VGA) .............................................................................................................................C-2
Intel® Graphics & Media Control Panel ..................................................................................................C-3
Display Devices & Options ......................................................................................................................C-5
Attaching Other Displays .........................................................................................................................C-6
Configuring an External Display in Windows 7 .....................................................................................C-10
Audio Configuration ...............................................................................................................................C-13
NVIDIA® Optimus™ Technology ........................................................................................................C-16
NVIDIA Control Panel ...........................................................................................................................C-18
XXVI
Preface
Optimus™ Customization Options .........................................................................................................C-20
Set PhysX® Configuration .....................................................................................................................C-24
Video Settings .........................................................................................................................................C-25
Specifications
Processor ...................................................................................................................................................D-2
Core Logic ................................................................................................................................................D-2
Display ......................................................................................................................................................D-2
Memory .....................................................................................................................................................D-2
Video Adapter Options .............................................................................................................................D-2
Storage ......................................................................................................................................................D-3
BIOS .........................................................................................................................................................D-3
Audio ........................................................................................................................................................D-3
Keyboard & Pointing Device ....................................................................................................................D-3
Interface ....................................................................................................................................................D-3
Slots ..........................................................................................................................................................D-3
Card Reader ..............................................................................................................................................D-4
Communication .........................................................................................................................................D-4
Security .....................................................................................................................................................D-4
Features .....................................................................................................................................................D-4
Operating System ......................................................................................................................................D-4
Power Management ..................................................................................................................................D-4
XXVII
Preface
Indicators ..................................................................................................................................................D-4
Power ........................................................................................................................................................D-4
Environmental Spec ..................................................................................................................................D-4
Physical Dimensions & Weight ................................................................................................................D-4
Windows 8
Overview ...................................................................................................................................................E-1
Windows 8 Start Screen & Desktop .........................................................................................................E-2
Apps & Tiles .............................................................................................................................................E-3
Desktop Application .................................................................................................................................E-4
Windows 8 Charms Bar ............................................................................................................................E-6
Windows 8 Control Panel .........................................................................................................................E-8
Windows 8 Taskbar ................................................................................................................................ E-11
LED Indicators ........................................................................................................................................E-12
Keyboard - Windows 8 ........................................................................................................................... E-13
Keyboard Shortcuts ................................................................................................................................E-14
Function/Hot Key Indicators & Control Center .....................................................................................E-15
Video Features ........................................................................................................................................E-16
To Configure Displays from Devices (Charms Bar): .............................................................................E-16
Power Options ........................................................................................................................................ E-17
Shut Down, Restart or Sleep ...................................................................................................................E-17
Ctrl + Alt + Delete Key Combination .................................................................................................... E-18
XXVIII
Preface
Wake On LAN Settings ..........................................................................................................................E-19
Running Metro UI Apps .........................................................................................................................E-20
Drivers & Utilities ..................................................................................................................................E-22
Driver Installation (Windows 8) ............................................................................................................. E-23
Driver Installation Order .........................................................................................................................E-24
Driver Installation Procedure .................................................................................................................. E-26
Chipset ....................................................................................................................................................E-26
Video (VGA) ..........................................................................................................................................E-26
NVIDIA Video (VGA) ...........................................................................................................................E-26
LAN ........................................................................................................................................................E-26
Card Reader ............................................................................................................................................E-26
TouchPad ................................................................................................................................................E-26
Hot Key ...................................................................................................................................................E-27
MEI Driver ..............................................................................................................................................E-27
Smart Card ..............................................................................................................................................E-27
Audio ......................................................................................................................................................E-27
Optional Drivers .....................................................................................................................................E-28
PC Camera ..............................................................................................................................................E-29
1.WLAN .................................................................................................................................................E-29
2.Fingerprint Reader Module ..................................................................................................................E-29
3.Bluetooth Module ................................................................................................................................E-29
4.Intel Rapid Storage Technology Driver ...............................................................................................E-29
XXIX
Preface
5.Intel Rapid Start Technology Driver ...................................................................................................E-29
6.Trusted Platform Module .....................................................................................................................E-29
7.Intel® Wireless Display Application ...................................................................................................E-29
PC Camera (Windows 8) ........................................................................................................................E-30
Metro UI Camera App ............................................................................................................................E-31
Taking Pictures/Capturing Video ...........................................................................................................E-33
Wireless LAN Settings (Windows 8) .....................................................................................................E-35
WLAN Configuration in Windows 8 ..................................................................................................... E-36
Charms Bar .............................................................................................................................................E-36
Desktop Mode .........................................................................................................................................E-39
Control Panel ..........................................................................................................................................E-40
Bluetooth Settings (Windows 8) .............................................................................................................E-42
Bluetooth Configuration in Windows 8 .................................................................................................. E-43
Desktop Mode .........................................................................................................................................E-43
Charms Bar .............................................................................................................................................E-43
Intel® Rapid Start Technology Driver ...................................................................................................E-47
Intel® Rapid Start Technology Configuration .......................................................................................E-48
XXX
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, card reader), TouchPad & Mouse & Audio Features.
• Chapter 3 The computer’s power management options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Wireless Display, Fingerprint,
Bluetooth & WLAN Combo and TruStudio Audio modules (some of which may be optional
depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the Control Center .
• Appendix C Information on the Video driver controls.
• Appendix D The computer’s specification.
• Appendix E Information on the Windows 8 operating system.
1
Overview 1 - 1
1
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”
on page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4
- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers
& Utilities” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
BIOS Settings
Note that the Microphone, WLAN module, Camera, Smart Card, Bluetooth module and Fingerprint Reader can be enabled/
disabled (they are enabled by default) in the BIOS (see page 5 - 11).
Not Included
Operating Systems (e.g. Windows 7/8) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
1
Overview 1 - 3
1
Windows 7/8 OS
In order to run Windows 7 or 8 (32 Bit) without limitations or decreased performance, your computer requires a minimum
1GB of system memory (RAM), however if you are running Windows 7 or 8 (64 bit) your computer requires a minimum
2GB of system memory (RAM).
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the Windows 7 (with Service Pack 1 in-
stalled) and Windows 8 operating systems are supported.
The majority of this menu covers information covers information related to the Windows 7 operating system,
however for specific information on the Windows 8 operating system see Appendix E.
Note: In order to run Windows 7 (SP1)/Windows 8 without limitations or decreased performance, your computer
requires a minimum 1GB of system memory (RAM).
1 - 4 Overview
Quick Start Guide
Shutdown
Note that you should always shut your computer
down by choosing the Shut Down command
from the bottom right of the Start menu in Win-
dows 7, or by choosing the Shut Down com-
mand from the Power item in Settings in the
Charms Bar (use the Windows Logo Key + C
key combination to access the Charms Bar) in
Windows 8. This will help prevent hard disk or
system problems.
135°
System Startup
1. Remove all packing materials, and place the comput er on a stable surfac e.
2. Securely attach any peripherals you want to use with the n otebook (e.g. keyboard and mouse) to their ports.
3. Attach the AC/DC adapter to the DC-In jack at th e rear of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
4. Use one hand to raise the
the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lif t the
computer by the lid/LCD).
5. Raise the lid/LCD to a comfortable viewing an gle, a nd pre ss the power bu tton on th e top left of the computer for
about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn
from orange to green when the computer powers on).
Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD
lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);
System Startup 1 - 5
1
use
1
Figure 1 - 2
LCD Panel Open
1. Built-In PC Camera
2. LCD
3.
Speakers
4.
LED Indicators
5. Power Button
6.
Keyboard
7. Built-In Microphone
8. TouchPad and
Buttons
9. Fingerprint Reader
(Optional)
Note that the Touchpad and Buttons
valid operational area is that indicated within the red dotted lines above.
2
1
8
9
7
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is
usually prohibited. Make
sure any wireless modules
are OFF if you are using
the computer aboard aircraft.
Use the appropriate function key combination to
toggle power to any wireless modules, and check
the indicators to see if any
modules are powered on or
not (see Table 1 - 2, on
page 1 - 9/Table 1 - 1, on
page 1 - 7).
6
5
4
3
Quick Start Guide
1 - 6 System Map: LCD Panel Open
System Map: LCD Panel Open
Quick Start Guide
LED Indicators
The LED indicators display helpful information about the current status of the computer.
Icon Color Description Icon Color Description
Number Lock is Activated
White
Orange The Battery is Charging
1
Caps Lock is Activated
White
Scroll Lock is Activated
White
White Hard Disk Activity Orange AC/DC Power is Plugged In
White
Orange
The (optional) Wireless LAN
Module is Powered On
The (optional) Bluetooth
Module is Powered On
Table 1 - 1 - LED Indicators
Blinking Orange
Green The Battery is Fully Charged
Blinking Orange* The Powered USB Port is On*
Green The Computer is On
Blinking Green The Computer is in Sleep Mode
The Battery has Reached Critically
Low Power Status
*Note: The powered USB 3.0 port (see Figure 1 - 6 on page 1 - 14) may be toggled on /off by means of the Fn + Power Button key
combination. When the powered USB port is on it will supply power (for charging devices only, not for operating devices) when the
system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level
above 20% (this may not work with certain devices - see page 8 - 13).
System Map: LCD Panel Open 1 - 7
1
Other Keyboards
If your keyboard is damaged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it automatically. However special functions/hot-keys
unique to the system’s
regular keyboard may not
work.
Num Lk & Scr Lk
Hold down the Fn Key
and Scr Lk/Num Lk to enable scroll lock/number
lock, and check the LED
indicator for status.
Numerical
Play/Pause Key
Function Keys
NumLk &
ScrLk Keys
Fn Key
Keypad
Game Control Keys
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.
Quick Start Guide
Keyboard
The keyboard has an embedded numerical keypad for easy numeric data input, and
features function keys to allow you to change operational features instantly. See
Table 1 - 2, on page 1 - 9 for full function key combination details and Appendix E
for Windows 8 keyboard information.
1 - 8 Keyboard
Figure 1 - 3 - Keyboard
Quick Start Guide
Function Keys & Visual Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed.
Keys Function/Visual Indicators Keys Function/Visual Indicators
Fn + ~ Play/Pause (in Audio/Video Programs) Fn + Esc Control Center Toggle (see over)
1
Fn + F1
Fn + F2
Fn + F3
Fn + F4 Sleep Toggle Fn + F12
Fn +F5/F6
Fn + F7 Change Display Configuration (see page C - 12/E - 16)
Touchpad Toggle
Turn LCD Backlight Off
(Press a key to or use Touchpad to turn on)
Mute Toggle
Volume Decrease/Increase
Fn +F8/F9
Fn + F10
Fn + F11
Fn + Power
Button
See also Table 1 - 1, on page 1 - 7 for Number Lock, Caps Lock and Scroll Lock indicators
Table 1 - 2 - Function Keys & Visual Indicators
Brightness Decrease/Increase
PC Camera Power Toggle
WLAN Power Toggle
Bluetooth Power Toggle
Powered USB 3.0 Port Power Toggle
Keyboard 1 - 9
1
Control Center
Click on any button to turn any of the modules (e.g.
TouchPad, Camera) on/off.
Click on the power conservation modes to switch between Performance, Balanced or Energy Star modes
(see page 3 - 10). To remove the Power Conservation
Modes screen just click in a blank area of the icon or
press a key on the keyboard.
Click on the buttons (or just click and hold the mouse
button) to adjust the slider for Brightness/Volume.
Click on Display Switch and click to choose a display
mode from the menu (see page C - 12/E - 16).
Quick Start Guide
Control Center
Press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to
toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn modules on/off. The Control Center in Windows 8 works under the Desktop app and
not under the Start screen, and does not feature the wireless/Bluetooth buttons and Airplane Mode (see page E
- 15 for Windows 8 information).
1 - 10 Control Center
Table 1 - 3 - Control Center
System Map: Front & Rear Views
Figure 1 - 4
Front View
1. LED Power Indicators
2. Security Lock Slot
3. Vent/Fan Intake
4. Display Port
5. Mini Display Port
6. DB9 Serial Port
7. DC-In Jack
1
3
4
6
2
5
7
3
Display Port / Mini Display Port
Note that the Display Port / Mini Display Port supports video and audio signals to attached
external displays.
Quick Start Guide
1
System Map: Front & Rear Views 1 - 11
1
Figure 1 - 5
Right View
1. Express Card Slot
2. Optical Device
Drive Bay
3. Headphone Jack
4. Microphone Jack
5. S/PDIF-Out Jack
6. Line-In Jack
7. 1 * USB 2.0 Port
2
4 53
7
6
1
USB Ports
Note that the connections to the USB ports only fit one way, do not force them.
ExpressCard Slot
The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
Quick Start Guide
System Map: Right View
1 - 12 System Map: Right View
Disk Eject Warning
Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop
the disk first then eject it, or press the stop button
twice.
CD/DVD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to
an unexpected power interruption) you may push the
end of a straightened paper clip into the emergency
eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole.
Don’t try to remove a floppy disk/CD/DVD while the
system is accessing it. This may cause the system to
“crash”.
Changing DVD Regional Codes
Go to the Control Panel and double-click Device
Manager (Hardware and Sound), then click th e +
next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties dialog
box, and select the DVD Region (tab) to bring up the
control panel to allow you to adjust the regional code.
DVD region detection is device dependent, not OSdependent. You can select your module’s region
code 5 times. The fifth selection is pe rmanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.
Quick Start Guide
1
System Map: Right View 1 - 13
1
Figure 1 - 6
Left View
1. RJ-45 LAN Jack
2. 1 * Powered USB
3.0 Port
3. 1 * USB 3.0 Port
4. Combined
eSATA/ USB 3.0
Port
5. Multi-in-1 Card
Reader
6. Smart Card
Reader
USB 3.0 Ports & Powered USB 2.0 Port
USB 3.0 ports are denoted by their blue color; USB 2.0 po rts are colored black. Note that
the USB 3.0 port requires a driver installation (see “USB 3.0” on page 4 - 7), does not support wake on USB and is not operational under DOS. The powered USB 3.0 port can
supply power (for charging devices only, not for operating devices) when the system is
off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the
battery with a capacity level above 20% (this may not work with certain devices - see page
8 - 13). Toggle power to this port by using Fn + power button.
Multi-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / RSMMC
SD (Secure Digital) / Mini SD / SDHC / SDXC
MS (Memory Stick) / MS Pro / MS Duo
2
1
2
4
5
3
6
Quick Start Guide
System Map: Left View
1 - 14 System Map: Left View
System Map: Bottom View
Figure 1 - 7
Bottom View
1. Sub Woofer
2. Fan Outlet/Intake
3. Component Bay
Cover
4. Primary HDD Bay
5. ODD Bay
6. Battery
Overheating
To prevent your computer from overheating make
sure nothing blocks the
vent(s)/fan intake(s)
while the computer is in
use.
1
2
4
5
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 11 for full instructions.
3
2
2
2
6
Quick Start Guide
1
System Map: Bottom View 1 - 15
1
Figure 1 - 8 - Start Menu & Control Panel
Click here to toggle Category View
Quick Start Guide
Windows 7 Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows 7 are accessed from the Start menu (see Ap-
pendix E for information on the Windows 8 OS). When you install programs and utilities they will be installed
on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click
the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features,
however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all
controls it may be necessary to toggle off Category View to view the control panel icons.
1 - 16 Windows 7 Start Menu & Control Panel
Quick Start Guide
Video Features
NVIDIA® Optimus™ Technology
Your computer features NVIDIA® Optimus™ switchable graphics technology. This seamless technology is designed to get the best performance from the graphics system while allowing longer battery life, without having
to manually change settings. The computer will automatically switch between the integrated UMA (Unified
Memory Architecture) GPU (power-saving - iGPU) and the discrete GPU (high performance - dGPU) when
required by the applications in use.
You can switch display devices, and configure display options from the Display control panel (in Appearances
and Personalization) in Windows 7 (see over or see Appendix E for information on the Windows 8 OS) or from
the Intel(R) Graphics and Media Control Panel (see page 1 - 19). For more detailed video information see
“Video Driver Controls” on page C - 1.
1
Video Features 1 - 17
1
1
2
1
2
Quick Start Guide
To access Display (Control Panel) and Screen Resolution in Windows:
1. Click Start and click Control Panel.
2. Click Display (icon) - In the Appearances and Personalization category.
3. Click Adjust Screen Resolution/Adjus t resolution.
4. Alternatively you can right-click the desktop and select Screen resolution.
5. Use the dropbox to select the screen Resolution (Figure 1 - 9).
6. Click Advanced settings (Figure 1 - 9) to bring up the Advanced properties tabs.
Figure 1 - 9 - Screen Resolution
1 - 18 Video Features
Quick Start Guide
234
3
4
To access the Intel(R) Graphics and Media Control Panel:
1. Click Advanced settings (Figure 1 - 9 on page 1 - 18) in the Display Settings control panel in Windows.
2. Click Graphics Properties (button) (Figure 1 - 10) in the Intel Graphics & Media Control Panel tab.
OR
3. Right-click the desktop and select Graphics Properties from the menu.
OR
4. Click the icon (Figure 1 - 10) in the taskbar and select Graphics Properties from the menu.
OR
5. Access the Intel(R) Graphics and Media Control Panel from the Windows control panel in Classic V iew.
6. Choose the application mode (Basic, Advanced or Wizard) required.
1
Figure 1 - 10 - Intel Graphics and Media Control Panel
Video Features 1 - 19
1
5
6
5
6
Quick Start Guide
To access the NVIDIA Control Panel:
1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 11).
OR
2. Double-click the icon (Figure 1 - 11) in the Windows control panel.
Figure 1 - 11 - NVIDIA Control Panel
1 - 20 Video Features
Quick Start Guide
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 15 or see Ap-
pendix E for information on the Windows 8 OS) allows you to configure power management features for your
computer. You can conserve power by means of power plans and configure the options for the power button,
sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power
saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change plan settings and click Change advanced power settings to access further configuration options. Pay attention to the instructions on battery care in “Battery Information” on page 3 - 11.
1
Figure 1 - 12 - Power Options
Power Options 1 - 21
1
Quick Start Guide
1 - 22
Storage Devices, Mouse, & Audio
Chapter 2: Storage Devices, Mouse, & Audio
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive
• Optical Device
• Multi-in-1 Card Reader
• Smart Card Reader
• Audio Features
• TouchPad and Buttons/Mouse
For information on the Windows 8 operating system see Appendix E.
2
Overview 2 - 1
Storage Devices, Mouse, & Audio
Power Safety
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Figure 2 - 1
Hard Disk Location
1
HDD Bay
1
2
Hard Disk Drive
The hard disk drive(s) is used to store your data in the computer. The hard disks) can
be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height
of 9.5 mm. The hard disk bay is accessible from the bottom of your computer as
seen below.
Further details on removing and inserting the hard disk are available in “Upgrading
the Hard Disk Drive(s)” on page 6 - 5.
2 - 2 Hard Disk Drive
Storage Devices, Mouse, & Audio
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-
dows. Click the Volume
icon on the notification
area to check the setting.
Peripherals must be
connected before you
turn on the system.
Figure 2 - 2
Optical Device
123
1
2
3
Optical Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page D - 3). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 15).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole
to open the tray.
2
Optical Device 2 - 3
Storage Devices, Mouse, & Audio
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
2
2 - 4 Optical Device
Handling CDs or DVDs
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
Storage Devices, Mouse, & Audio
DVD Region Note
DVD region detection is
device dependent, not
OS-dependent. You can
select your module’s region code 5 times. The
fifth selection is permanent. This cannot be altered even if you change
your operating system
or you use the module in
another computer.
Figure 2 - 3
DVD Region Codes
• Region 1 - USA & Canada
• Region 2 - Western Europe, Japan,
South Africa, Middle East & Egypt
• Region 3 - South-East Asia, Taiwan,
South Korea, The Philippines, Indonesia, Hong Kong
• Region 4 - South & Central Amer-
ica, Mexico, Australia, New Zealand
• Region 5 - N Korea, Russia, Eastern
Europe, India & Most of Africa
• Region 6 - China
DVD Regional Codes
To change the DVD regional codes:
1. Go to the Control Panel
2. Double-click Device Manager (Hardware and Sound), then click the + next to
DVD/CD-ROM drives.
3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and
select the DVD Region (tab) to bring up the control p anel to allow you to adjust the
regional code.
2
Optical Device 2 - 5
Storage Devices, Mouse, & Audio
Card Reader Cover
Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust getting in to the card reader.
Push-Push Card
Reader
The card reader features a push-in/push-out
card insertion and ejection mechanism. Simply
push the card to insert
and eject it, however Ms
Duo cards require an
adapter.
Figure 2 - 4
Left View
1. Card Reader
• MMC (MultiMedia Card) / RSMMC
• SD (Secure Digital) / Mini SD / SDHC / SDXC
• MS (Memory Stick) / MS Pro / MS Duo
1
2
Multi-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader” on page 4 - 7).
Note: Some of these cards require PC adapters that are usually supplied with the
cards.
2 - 6 Multi-in-1 Card Reader
Storage Devices, Mouse, & Audio
Smart Card Driver
Smart Cards usually require a driver for any
proprietary smart card
system. This driver will
usually be supplied by
your system administrator as applicable to your
particular Smart Card
system.
Figure 2 - 5
Left View
1. Smart Card
Reader
1
Smart Card Reader
The Smart Card reader reads pocket-sized Smart Cards, chip cards, or integrated circuit cards (ICC) with embedded integrated circuits. Smart Cards can be used for security identification, authentication, data storage and application processing within
large organizations.
A Smart Card uses a gold contact that connects to a tiny microprocessor and memory
chips embedded inside the card. The card is usually used to store authentication data
e.g. a user name and password. The computer’s Smart Card reader communicates
through the gold contact on the card to the microprocessor, and if the data on the card
matches that stored in the computer, then access is granted. A Smart Card can also
be used to securely encrypt and decrypt individual files on the computer.
2
Smart Card Reader 2 - 7
Storage Devices, Mouse, & Audio
Volume Adjustment
The sound volume level is
set using the volume control within Windows (and
the volume function keys
on the computer). Click the
volume icon in the notification area to check the setting.
Headphone
Configuration
It is recommended that you
set the Speaker Configu-
ration to Stereo (not to 5.1
or 7.1 Speaker) when listening through headphones
in order to maximize audio
quality.
Figure 2 - 6
Realtek Audio
Manager
Right-click the icon
to access the menu
above.
See “Audio Configur ation” on page C - 13 for a description of the audi o configuration
when connecting an HDMI supported display device.
2
Audio Features
You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the notifi-
cation area/control panel (right-click the notification area icon to bring up an au-
2 - 8 Audio Features
dio menu). The volume may also be adjusted by means of the Fn + F5/F6 key
combination (see Table 1 - 2, on page 1 - 9).
Storage Devices, Mouse, & Audio
Figure 2 - 7
Realtek Audio
Manager -
Recording Setup
Setup for Audio Recording
To record audio sources on your computer at optimum quality follow the instructions below:
1. Click
2. Click Realtek HD Audio Manager (or right-click the notification area icon and
3. Click Microphone Effects (tab) in Microphone (tab), and then click to select
4. Click OK to close the control panel and save the settings.
Start
, and click
and make sure you are in
select Sound Manager).
Noise Suppression (button), or adjust th e Recording Volume level to around 60,
to obtain the optimum recording quality.
Control Panel
Classic View
(or point to
.
Settings
and click
Control Panel
2
)
Audio Features 2 - 9
Storage Devices, Mouse, & Audio
Figure 2 - 8
Speaker
Configuration (7.1)
Auto Popup Dialog
You should enable the
auto popup dialog to automatically detect when a
device has been
plugged-in. If disabled,
double-click connector
settings and click the
box to enable the auto
popup detection of
plugged-n devices.
Connector Settings
2
2 - 10 Audio Features
Setup for 5.1 or 7.1 Surround Sound
To setup your system for 5.1 or 7.1 surround sound you will need to connect the audio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out
jacks (note: the S/PDIF jack is used for 7.1 surround sound only).
1. Click
2. Click Realtek HD Audio Manager (or right-click the notification area icon and
3. Click Speakers (tab) and click Speaker Configuration (tab).
4. Select 5.1 or 7.1 Speaker from the Speaker Configuration pull-down menu.
Start
, and click
and make sure you are in
select Sound Manager).
Control Panel
(or point to
Classic View
Settings
.
and click
Control Panel
)
Storage Devices, Mouse, & Audio
Figure 2 - 9
Connected Device
Auto Popup
Note: Side Speaker Out is required for 7.1 Surround only.
5. Plug the front speaker cables into the Headphone-Out Jack.
6. Plug in the other cables (you may require an adapter to connect each cable to the
appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as
follows:
• Line-In Jack = Rear Speaker Out
• Microphone-In Jack = Center/Subwoofer Speaker Out
• S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)
7. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on
page 2 - 10).
8. Click to put a tick in the appropriate box according to the speaker plugged-in (e.g.
Rear Speaker Out), and then click OK to save the setting.
9. Click OK to exit Realtek HD Audio Manager.
2
Audio Features 2 - 11
Storage Devices, Mouse, & Audio
Mouse Driver
If you are using an external mouse your operating system may be
able to auto-configure
your mouse during its
installation or only enable its basic functions.
Be sure to check the
device’s user documentation for details.
2
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.
2 - 12 TouchPad and Buttons/Mouse
Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 7) you
TouchPad Scrolling
This computer model series may feature different
TouchPad versions.
These TouchPads may
differ in their vertical
scrolling function in most
scrollable windows.
Some TouchPads require
sliding the finger up and
down on the right of the
TouchPad to scroll the
window. Other versions
require tapping/holding
down the finger at the top
right or bottom right of the
TouchPad to scroll the
window.
Figure 2 - 10
Mouse Properties
can configure the functions from the Mouse control panel in Windows, or by d oubleclicking the TouchPad driver icon in the notification area. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options
to your preferences. You will find further information at www.synaptics.com.
Storage Devices, Mouse, & Audio
2
TouchPad and Buttons/Mouse 2 - 13
Storage Devices, Mouse, & Audio
Show Video
You can get a clearer
view of the gestures involved by clicking the
Show Video option for
each gesture item.
Select the gesture (Pinch
Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Settings left tree menu
and click the Show Video
button to see the demonstration video.
For more details on any of
the gestures see the help
in the lower part of the
right menu window.
Figure 2 - 11
Mouse Properties -
Device Settings
2
Gestures and Device Settings
The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the TouchPad to perform specific actions to manipulate documents, objects and applications.
You can configure the settings from the Device Settings tab in Mouse Properties:
1. Click
2. Click Mouse (Hardware and Sound).
3. Click Device Settings (tab) and click Settings.
4. Use the menu tree on the lef t to access the user configurable settings.
Start
, and click
Control Panel
(or point to
Settings
and click
Control Panel
).
2 - 14 TouchPad and Buttons/Mouse
Storage Devices, Mouse, & Audio
Figure 2 - 12
SmartSense
Smart Sense
The Smart Sense feature helps prevent operating the Touchpad by accident, by recognizing when your palm is resting on it or brushing its surface while you are typing.
You can adjust the sensitivity of Smart Sense by moving the slider towards Max (to
help remove undesired pointer movement or clicks) or Off (if it misses intended motions or taps).
2
TouchPad and Buttons/Mouse 2 - 15
Storage Devices, Mouse, & Audio
Figure 2 - 13
Scrolling Gesture
Figure 2 - 14
Zooming Gesture
2
Scrolling
The Two-Finger scrolling feature works in most scrollable windows an d allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).
Zooming
The Pinch Zoom gesture can be used to perform the same function as a scroll wheel
in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and
slide them apart to zoom in, or closer together to zoom out.
2 - 16 TouchPad and Buttons/Mouse
Storage Devices, Mouse, & Audio
Figure 2 - 15
Rotating Gesture
Figure 2 - 16
Flick/Press
Gesture
Rotating
Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another
finger near the middle of the TouchPad and slide it in a circular motion around the
stationary finger (clockwise or counterclockwise) to rotate the object.
Three Finger-Flick/Three Fingers Down (Press)
The Three Finger-Flick gesture may be used to enhance navigation with a variety of
applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.
2
TouchPad and Buttons/Mouse 2 - 17
Storage Devices, Mouse, & Audio
2
2-18
Chapter 3: Power Management
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
(Note: All pictures used
on the following pages
are from the Windows 7
OS.)
Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system.
This chapter covers:
• The Power Sources
• Turning On the Computer
• Power Plans
• Power-Saving States
• Configuring the Power Buttons
• Battery Information
For information on the Windows 8 operating system see Appendix E.
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
3
Overview 3 - 1
Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button on the top left of the computer for about 2 - 3 seconds to
turn the computer “on” (note that the power LED on the front of the computer will
turn from orange to green when the computer powers on).
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 15).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 11.
3 - 2 The Power Sources
Turning On the Computer
Forced Off
If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the system to turn itself off.
Power Button as
Stand by or
Hibernate Button
You can use the OS’s
Power Options control
panel to set the power
button to send the system into Stand by or Hibernate mode (see your
OS’s documentation, or
“Configuring the Power Buttons” on page 3
- 8 for details).
Shut Down
Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk
or system problems.
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.
Power Management
3
Turning On the Computer 3 - 3
Power Management
Resuming
Operation
See Table 3 - 1, on
page 3 - 9 for informa-
tion on how to resume
from a power-saving
state.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
Figure 3 - 1
Power Plan
Advanced Settings
(Win 7)
Power Plans
The computer can be configured to conserve power by means of power plans. You
3
can use (or modify) an existing power plan, or create a new one.
3 - 4 Power Plans
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Each Windows power plan will also adjust the processor performance of your ma-
Figure 3 - 2
Power Plans (Win 7)
Click to Show/Hide
additional
power plans
chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
Power Management
3
Power Plans3-5
Power Management
Power-Saving States
You can use power-saving states to stop the computer’s operation and restart where
3
you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.
Sleep
In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.
The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.
If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.
3 - 6 Power-Saving States
Hibernate
Figure 3 - 3
Start Menu Power
Hibernate uses the least amount of power of all the power-saving states and saves
all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.
Shut down
You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from Shut down takes longer than
from Sleep or Hibernate.
Power Management
3
Power-Saving States 3 - 7
Power Management
Password
Protection
It is recommended that
you enable a password
on wake up in order to
protect your data.
However you can disable this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that
are currently unavailable).
Figure 3 - 4
Power Options
Define Power
Buttons
3
Configuring the Power Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to a power-saving state. Click Choose what the power buttons do on
the left menu in Power Options to bring up the menu.
3 - 8 Configuring the Power Buttons
Resuming Operation
Closing the Lid
If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.
Table 3 - 1
Resuming
Operation
Power Button
When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down
hot key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down).
You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F4 key combo).
Power Management
3
Power Status
Power Off Off Press the Power Button
Sleep Blinking Green
Hibernate
Display Turned Off Green Press a Key or Move the Mouse/Touchpad
Icon Color
Off (battery)
Orange (AC/DC adapter)
To Resume
Press the Power Button
Press the Sleep Button (Fn + F4 Key Combo)
Press the Power Button
Configuring the Power Buttons 3 - 9
Power Management
Power Conservation
Modes
The Energy Star setting
will result in maximum
power saving, but with
the possible loss of
some performance.
Setting the mode to Bal-
ance will give power
saving matched with
performance.
Performance will give
optimum computer performance but with less
power conservation.
Figure 3 - 5
Control Center
3
Power Conservation Modes
This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period
of inactivity. Adjust Power Conservation Modes from the Control Center:
1. Press the Fn + Esc key combination to toggle the Control Center on/off.
2. Click either the Performance, Balanced or Energy Star button.
3. Click in a blank area of the icon or press a key on the keyboard to exit Power
Conservation Mode without making any changes.
3 - 10 Configuring the Power Buttons
Battery Information
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 6
Battery Icon
(Notification Area) &
Battery Advanced
Settings
Follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Change plan settings > Change advanced power settings (see Figure
3 - 1 on page 3 - 4).
Click the battery icon in the notification area to see the current battery level and
charge status.
Power Management
3
Battery Information 3 - 11
Power Management
Windows Mobility
Center
The Windows Mobility
Center control panel
provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.
Figure 3 - 7
Windows Mobility
Center
3
Conserving Battery Power
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
• Close wireless, Bluetooth, modem or co mmunication applications when they are
not being used.
• Disconnect/remove any unnecessary external devices e.g. USB devices.
3 - 12 Battery Information
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery”
on page 6 - 3.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 15 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 7 for information on the battery charge status, and to “Battery Information” on page 3 - 11 for more information on how to maintain and properly
recharge the battery pack.)
Power Management
3
Battery Information 3 - 13
Power Management
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your distributor/supplier. If the battery has been dropped we
do not recommend using it any further, as even if the comp uter continues to work with a
damaged battery in place, it may cause circuit damage, which may possibly result in fire. It
is recommended that you replace your computer battery every two years.
Caution
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances.
• DO NOT expose the battery to fire or high temperatures, it may explode.
3
• DO NOT connect the metal terminals (+, -) to each other.
3 - 14 Battery Information
Battery FAQ
Figure 3 - 8
Power Plan Create
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for discharging the battery and set all the options to Never.
Power Management
3
Battery Information 3 - 15
Power Management
Figure 3 - 9
Change Plan
Settings / Change
Advanced Power
Settings
3
3. Click Change plan settings (after creating it) and click Change plan settings >
Change advanced power settings.
3 - 16 Battery Information
4. Scroll down to Battery and click + to expand the ba ttery options.
Figure 3 - 10
Power Options
Advanced Settings -
Battery
5. Choose the options below (click Yes if a warning appears):
• Low battery levels = 0%
• Critical battery Levels = 1%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing
Power Management
3
Battery Information 3 - 17
Power Management
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
3
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
3 - 18 Battery Information
Chapter 4: Drivers & Utilities
Driver Installation &
Power
When installing drivers make sure your
computer is powered
by the AC/DC adapter
connected to a working power source.
Some drivers draw a
significant amount of
power during the installation procedure, and if
the remaining battery
capacity is not adequate
this may cause the system to shut down and
cause system problems
(note that there is no
safety issue involved
here, and the battery will
be rechargeable within 1
minute).
This chapter deals with installing the drivers and utilities essential to the operation or
improvement of some of the computer’s subsystems. The system takes advantage of
some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during
operating system installation. Instead, you need to manually install some system-required drivers and utilities.
See Appendix E for specific information on the Windows 8 operating system.
What to Install
The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 3
lists what you need to install and it is very important that the drivers are installed
in the order indicated.
Module Driver Installation
The procedures for installing drivers for the PC Camera, WLAN, Fingerprint, and
Combination Bluetooth & WLAN modules (you should also install the Intel Rapid Storage and Rapid Start Technology drivers as instructed in Chapter 7) are pro-
vided in “Modules” on page 7 - 1.
Drivers & Utilities
4
What to Install 4 - 1
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.
4
Figure 4 - 1 - Drivers Installer Screen 1
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, (you
should note down the drivers as you install them).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
Note: If you need to reinstall any driver, you should uninstall the
driver first.
4 - 2 Driver Installation
Figure 4 - 2 - Drivers Installer Screen 2
Drivers & Utilities
Win 7 SP1/Win 8 Driver Page Win 7 SP1/Win 8 Driver
Chipset Page 4 - 6 PC Camera Module Page 7 - 2
Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 10
NVIDIA Video (VGA) Page 4 - 6 Intel® Wireless Display Application Page 7 - 10
LAN Page 4 - 7 Security Modules (Fingerprint & TPM) Page 7 - 34
Card Reader Page 4 - 7 Bluetooth Module Page 7 - 43
TouchPad Page 4 - 7
Hot Key Page 4 - 7 Intel® Rapid Start Technology Driver Page 7 - 50
USB 3.0 Page 4 - 7 Trusted Platform Module Page 7 - 65
MEI Driver Page 4 - 7
Audio Page 4 - 7
Intel® Rapid Storage Technology Driver
(required for hard disks in AHCI & RAID modes)
All drivers provided are for Windows 7 with Service Pack 1 or Windows 8 (see Appendix E for Win 8 information).
Page
Page 7 - 49
Table 4 - 1 - Driver Installation
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.
4
Driver Installation 4 - 3
Drivers & Utilities
Manual Driver Installation
Click the Browse CD/DVD button in the Drivers Installer application and browse to the executable file in
the appropriate driver folder.
4
Windows Update
After installing all the drivers make sure you enable
Windows Update in order to get all the latest securi ty
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows Update” on page 4 -
8 for instructions.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as
outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2. Double-click Device Manager (Hardware and
Sound > Device Manager).
3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
4 - 4 Driver Installation
Drivers & Utilities
User Account Control
If a User Account Control prompt appears as part of
the driver installation procedure, click Continue/Al-
low, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or Install to continue the installation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found” during the installation procedure (other than when out-
lined in the driver install procedure), click Cancel
to close the window, and follow the installation procedure.
4
Driver Installation 4 - 5
Drivers & Utilities
Driver Installation General Guidelines
The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.
Drivers are always subject to upgrade and revision so
the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish)
unless you are an advanced user. In many cases a restart is required to install the driver.
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.
4
Chipset
1. Click 1.Install Chipset Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
Video (VGA)
1. Click 2.Install VGA Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
NVIDIA Video (VGA)
1. Click 3.Install nVIDIA VGA Driver > Yes.
2. Click AGREE AND CONTINUE (button) to
accept the terms of the license agreement.
3. Click Next > Next.
4. Click the REST ART NOW button to restart
the computer.
Note: After installing the video driver go to the Display/Display Settings control panel to adjust the vid-
eo settings to the highest resolution.
4 - 6 Driver Installation
Drivers & Utilities
LAN
1. Click 4.Install LAN Driver > Yes.
2. Click Install Drivers and Software (button).
3. Click Next.
4. Click the button to accept the license agreement
and click Next.
5. Click Next > Install.
6. Click Finish.
Card Reader
1. Click 5.Install Cardreader Driver > Yes.
2. Click Finish.
TouchPad
1. Click 6.Install Touchpad Driver > Yes.
2. Click Next.
3. Click the button to accept the license, and then
click Next.
4. Click Finish > Restart Now to restart the com-
puter.
Hot Key
1. Click 7.Install Hotkey AP > Yes.
2. Click Next > Next.
3. Click Finish > Finish to restart your computer.
USB 3.0
1. Click 8.Install USB 3.0 Driver > Yes.
2. Click Next > Yes > Next > Next.
3. Click Finish to restart the computer.
MEI Driver
1. Click 9.Install MEI Driver > Yes.
2. Click Next > Yes > Next.
3. Click Finish to restart the computer.
Audio
1. Click 10. Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
See over.
4
Driver Installation 4 - 7
Drivers & Utilities
Windows Update
After installing all the drivers make sure you enable Windows Update in order to get all the latest security up-
dates etc. (all updates will include the latest hotfixes
from Microsoft).
To enable Windows Update make sure you are con-
nected to the internet:
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2. Click Window s Update (System and Security/
Security).
3. Click Check for updates (button).
4. The computer will now check for updates (you
need to be connected to the internet).
5. Click Install now (button) to begin checking for the
updates.
6. Click Install updates (button) to install the
updates.
After installing the audio driver the system will not return to the Drivers Installer screen. To install any of
the optional drivers, eject the Device Drivers & Utili-
ties + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click
4
Option Drivers (button) to access the optional driver
menu.
It is recommended that you install the Intel Rapid
Storage and Rapid Start Technology drivers (see
“Intel® Rapid Storage Technology Driver” on
page 7 - 49 - required for hard disks configured in
AHCI mode - and “Intel® Rapid Start Technology
Driver” on page 7 - 50).
See Appendix E for specific information on the Win-
dows 8 operating system.
4 - 8 Driver Installation
Drivers & Utilities
Models A & B
Windows Experience Index
After Video (VGA) driver has been installed, and the
system restarted, the OS will automatically run the
"Winsat.exe" to rate the performance. If you have restarted the system during this time then follow the instructions below to update the information.
After the drivers are installed follow this procedure to
ensure an accurate rating from the Windows Experi-
ence Index (make sure the AC/DC adapter is plugged
in):
1. Click Start, and click Control Panel.
2. Click Performance Information and Tools
(System and Security > System > Check the
Windows Experience Index).
3. Click “Rate this computer/Refresh Now/Re-
run the assessment”.
4. The computer will take a few minutes to assess
the system performance.
5. Close the control panel.
Optional Drivers
See the pages indicated in Table 4 - 1, on page 4 - 3
for the driver installation procedures for any modules
included in your purchase option.
4
Figure 4 - 3 - Optional Drivers Installer Screen
Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo
modules.
Driver Installation 4 - 9
Drivers & Utilities
4
4-10
Loading...