Clevo P150e, P170e User Manual

Download

Page 1

V12.3.00

Page 2

Page 3

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©March 2012

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

Page 4

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

EuP-Standby and Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode or standby mode:

• Standby Mode < 2W

• Off Mode < 1W

Page 5

III

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas mo st q uality marking s are voluntary.

Page 6

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc e d ra di o/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

Page 7

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-l ocated or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environ ment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

Page 8

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit:

• Model A - Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 9.47A (180W) minimum.

• Model B - Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 6.3A (120W) minimum.

• Model C - Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 11.57A (220W) minimum.

This Computer’s Optical Device is a Laser Class 1 Product

Page 9

VII

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

Do not expose it to excessive

heat or direct sunlight.

Do not leave it in a place where

foreign matter or moisture may

affect the system.

Don’t use or store the computer

in a humid environment.

Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

Page 10

VIII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g proc edur es for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

5. Take care when using peripheral devices.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

Do not disassemble the computer by yourself.

Perform routine maintenance on your computer.

Use only approved brands of peripherals.

Unplug the power cord befor e attaching peripheral devices.

Page 11

Preface

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a

steady , uninte rrupted power suppl y. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third

prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not

by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current

load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power

supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord). You must also remove your battery in order to prevent accidentally turning the machine on.

Page 12

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansio n or swelling, however this is part of the battery’s safety mecha-

nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-

ture environments, and do not store unused batteries for extended per iods.

See also the general battery precautionary information overleaf for further information.

Page 13

Preface

General Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replac ement to your service repre sentati ve or qual-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Page 14

XII

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Page 15

XIII

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapte r. However ,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or r equire proof of ownersh ip for both ha rd-

ware and software. Make sure your “papers” are handy.



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. T o prevent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

Page 16

XIV

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.

Page 17

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods o f time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below th e

level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on

a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angl es

when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent

and short breaks are better than fewer and longer breaks.

Page 18

XVI

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflecti ons from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your service center.

Page 19

XVII

Preface

Contents

Notice .............................................................................................................................................................I

EuP-Standby and Off Mode Power Consumption Statement: ..................................................................... II

FCC Statement ............................................................................................................................................IV

FCC RF Radiation Exposure Statement: .....................................................................................................V

Instructions for Care and Operation ......................................................................................................... VII

Power Safety ...............................................................................................................................................IX

Polymer Battery Precautions .......................................................................................................................X

General Battery Precautions .......................................................................................................................XI

Cleaning .................................................................................................................................................... XII

Servicing ................................................................................................................................................... XII

Travel Considerations ..............................................................................................................................XIII

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Software ........................................................................................................................................1-4

Model Differences .....................................................................................................................................1-5

System Startup ...........................................................................................................................................1-6

Page 20

XVIII

Preface

System Map: LCD Panel Open - Models A & B .......................................................................................1-7

System Map: LCD Panel Open - Model C ................................................................................................1-8

LED Indicators ...........................................................................................................................................1-9

Keyboard - Models A & C .......................................................................................................................1-10

Keyboard LED - Models A & C ..............................................................................................................1-11

Effects Buttons & Help (Models A & C) ................................................................................................1-13

Keyboard - Model B ................................................................................................................................1-14

Function Keys & Visual Indicators .........................................................................................................1-15

Control Center .........................................................................................................................................1-16

System Map: Front & Rear Views ...........................................................................................................1-17

System Map: Right View .........................................................................................................................1-18

System Map: Left View ...........................................................................................................................1-19

System Map: Bottom View - Models A & B ..........................................................................................1-20

System Map: Bottom View - Model C ....................................................................................................1-21

Windows 7 Start Menu & Control Panel .................................................................................................1-22

Video Features .........................................................................................................................................1-23

NVIDIA® Optimus™ Technology .........................................................................................................1-23

Power Options .........................................................................................................................................1-27

Storage Devices, Mouse, & Audio

Overview ....................................................................................................................................................2-1

Hard Disk Drive .........................................................................................................................................2-2

Page 21

XIX

Preface

Optical Device ...........................................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-in-1 Card Reader ..............................................................................................................................2-6

Audio Features ...........................................................................................................................................2-7

Setup for Audio Recording ........................................................................................................................2-8

Setup for 5.1 or 7.1 Surround Sound .........................................................................................................2-9

TouchPad and Buttons/Mouse .................................................................................................................2-11

Gestures and Device Settings ..................................................................................................................2-13

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

Battery ........................................................................................................................................................3-2

Turning On the Computer ..........................................................................................................................3-3

Power Plans ...............................................................................................................................................3-4

Power-Saving States ..................................................................................................................................3-6

Sleep ..........................................................................................................................................................3-6

Hibernate ....................................................................................................................................................3-7

Shut down ..................................................................................................................................................3-7

Page 22

Preface

Configuring the Power Buttons .................................................................................................................3-8

Resuming Operation ..................................................................................................................................3-9

Power Conservation Modes .....................................................................................................................3-10

Battery Information .................................................................................................................................3-11

Conserving Battery Power .......................................................................................................................3-12

Battery Life ..............................................................................................................................................3-13

New Battery .............................................................................................................................................3-13

Recharging the Battery with the AC/DC Adapter ...................................................................................3-13

Proper handling of the Battery Pack ........................................................................................................3-14

Battery FAQ .............................................................................................................................................3-15

Drivers & Utilities

What to Install ............................................................................................................................................4-1

Module Driver Installation ........................................................................................................................4-1

Driver Installation ......................................................................................................................................4-2

Manual Driver Installation .........................................................................................................................4-4

Updating/Reinstalling Individual Drivers ..................................................................................................4-4

User Account Control ................................................................................................................................4-5

Windows Security Message .......................................................................................................................4-5

New Hardware Found ................................................................................................................................4-5

Driver Installation Procedure .....................................................................................................................4-6

Chipset .......................................................................................................................................................4-6

Page 23

XXI

Preface

Video (VGA) .............................................................................................................................................4-6

NVIDIA Video (VGA) ..............................................................................................................................4-6

LAN ...........................................................................................................................................................4-6

Card Reader ...............................................................................................................................................4-7

TouchPad ...................................................................................................................................................4-7

Hot Key ......................................................................................................................................................4-7

USB 3.0 ......................................................................................................................................................4-7

MEI Driver .................................................................................................................................................4-7

Audio .........................................................................................................................................................4-7

Windows Experience Index .......................................................................................................................4-8

Optional Drivers ........................................................................................................................................4-9

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Power-On Self Test (POST) ...............................................................................................................5-2

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

The Setup Utility ........................................................................................................................................5-4

Entering Setup ...........................................................................................................................................5-4

Setup Screens .............................................................................................................................................5-5

Main Menu .................................................................................................................................................5-6

Page 24

XXII

Preface

System Time & Date (Main Menu) ...........................................................................................................5-6

SATA Port # (Main Menu) ........................................................................................................................5-7

System/Extended Memory (Main Menu) ..................................................................................................5-7

MB Series / BIOS Revision / KBC/EC firmware Revision / VGA Card (Main Menu) ...........................5-7

Advanced Menu .........................................................................................................................................5-8

Advanced Chipset Control (Advanced Menu) ..........................................................................................5-8

Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control) ...............................................5-9

Intel(R) Rapid Start Technology (Advanced Menu) .................................................................................5-9

SATA Mode (Advanced Menu) ................................................................................................................5-9

Legacy USB Support (Advanced Menu) .................................................................................................5-10

Boot Logo (Advanced Menu) ..................................................................................................................5-10

Power On Boot Beep (Advanced Menu) .................................................................................................5-10

Battery Low Alarm Beep (Advanced Menu) ...........................................................................................5-10

Security Menu ..........................................................................................................................................5-11

Set Supervisor Password (Security Menu) ..............................................................................................5-11

Password on boot: (Security Menu) ........................................................................................................5-12

Boot Menu ...............................................................................................................................................5-13

Boot Option Priorities (Boot Menu) ........................................................................................................5-14

Exit Menu ................................................................................................................................................5-15

Upgrading The Computer

Overview ....................................................................................................................................................6-1

Page 25

XXIII

Preface

When Not to Upgrade ................................................................................................................................6-2

Removing the Battery ................................................................................................................................6-3

Upgrading the Optical Device (Model A/B) .............................................................................................6-4

Upgrading the Optical Device (Model C) .................................................................................................6-5

Upgrading the Hard Disk Drive(s) ............................................................................................................6-6

Upgrading the System Memory (RAM) ..................................................................................................6-16

Replacing the Primary System Memory Modules ...................................................................................6-17

Modules

Overview ....................................................................................................................................................7-1

Setting Up SATA RAID or AHCI Mode ..................................................................................................7-2

AHCI Mode ...............................................................................................................................................7-2

RAID ..........................................................................................................................................................7-2

Intel® Rapid Storage Technology Application .........................................................................................7-2

SATA RAID Setup Procedure (BIOS) ......................................................................................................7-5

RAID Setup (Intel Matrix) .........................................................................................................................7-6

Intel Rapid Storage Technology ................................................................................................................7-9

IRST Driver Installation ............................................................................................................................7-9

RAID Volume Data Verification and Repair ..........................................................................................7-12

Replacing and Reverting Recovery and Master Volumes .......................................................................7-12

PC Camera Module ..................................................................................................................................7-15

PC Camera Driver Installation .................................................................................................................7-16

Page 26

XXIV

Preface

PC Camera Audio Setup ..........................................................................................................................7-17

Wireless LAN Module .............................................................................................................................7-23

3rd Party 802.11b/g/n Driver Installation ................................................................................................7-24

Intel® WLAN Driver Installation ............................................................................................................7-25

Connecting to a Wireless Network in Windows 7 ...................................................................................7-28

Connecting to a Wireless Network Using Intel® PROSet Wireless .......................................................7-31

Intel® My WiFi Configuration ................................................................................................................7-33

Windows Mobility Center .......................................................................................................................7-42

Intel® Wireless Display Application .......................................................................................................7-43

Intel® WiDi Application Installation ......................................................................................................7-44

Intel® Wireless Music Driver Installation ...............................................................................................7-44

Intel® WiDi Application Configuration ..................................................................................................7-45

Fingerprint Reader Module ......................................................................................................................7-48

Fingerprint Reader Driver Installation .....................................................................................................7-49

AuthenTec TrueSuite Application ...........................................................................................................7-50

Bluetooth Module ....................................................................................................................................7-60

3rd Party Bluetooth Combo Driver Installation Information ..................................................................7-61

3rd Party Bluetooth Combo Driver Version 1 Installation ......................................................................7-62

3rd Party Bluetooth & WLAN Combo Settings ......................................................................................7-63

3rd Party Bluetooth Networking Setup ....................................................................................................7-66

3rd Party Bluetooth & WLAN Combo Module Configuration ...............................................................7-67

Intel Bluetooth Combo Driver Installation ..............................................................................................7-70

Page 27

XXV

Preface

Standard Bluetooth Configuration in Windows 7 ...................................................................................7-71

THX TruStudio Pro Audio ......................................................................................................................7-75

THX TruStudio AP Installation ...............................................................................................................7-75

THX TruStudio Pro Activation ...............................................................................................................7-76

THX TruStudio Pro Application .............................................................................................................7-76

Intel® Rapid Storage Technology Driver ................................................................................................7-80

Intel® Smart Response Technology ........................................................................................................7-81

Enabling Intel Smart Response Technology ............................................................................................7-82

Intel® Rapid Start Technology Driver ....................................................................................................7-85

Intel® Rapid Start Technology Configuration ........................................................................................7-86

Intel® Rapid Start Technology Driver Installation .................................................................................7-92

Troubleshooting

Overview ....................................................................................................................................................8-1

Basic Hints and Tips ..................................................................................................................................8-2

Backup and General Maintenance .............................................................................................................8-3

Viruses .......................................................................................................................................................8-4

Upgrading and Adding New Hardware/Software ......................................................................................8-5

Problems & Possible Solutions ..................................................................................................................8-7

Bluetooth Connection Problems ..............................................................................................................8-16

Intel® WLAN & Bluetooth V3.0+HS Combo Modules .........................................................................8-20

Installing Windows 7 (pre Service Pack 1) for RAID Systems with Advanced Format Disks ...............8-21

Page 28

XXVI

Preface

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Ports and Jacks ..........................................................................................................................................A-2

Card Reader ..............................................................................................................................................A-2

DC-In Jack ................................................................................................................................................A-2

DisplayPort ...............................................................................................................................................A-2

DVI-Out Port ............................................................................................................................................A-2

e-SATA / USB 3.0 Combo Port ...............................................................................................................A-2

HDMI-Out Port .........................................................................................................................................A-3

Headphone-Out Jack .................................................................................................................................A-3

Line-In Jack ..............................................................................................................................................A-3

Microphone-In Jack ..................................................................................................................................A-3

Mini-IEEE 1394a Port ..............................................................................................................................A-4

RJ-45 LAN Jack .......................................................................................................................................A-4

S/PDIF-Out Jack .......................................................................................................................................A-4

Security Lock Slot ....................................................................................................................................A-4

USB 2.0/1.1 Ports .....................................................................................................................................A-5

USB 3.0 Port .............................................................................................................................................A-5

Powered USB 3.0 Port ..............................................................................................................................A-5

Control Center

Overview ...................................................................................................................................................B-1

Page 29

XXVII

Preface

Video Driver Controls

Video Driver Installation ..........................................................................................................................C-1

Video (VGA) ............................................................................................................................................C-1

NVIDIA Video (VGA) .............................................................................................................................C-1

NVIDIA® Optimus™ Technology ..........................................................................................................C-2

Intel® Graphics & Media Control Panel ..................................................................................................C-4

Display Devices & Options ......................................................................................................................C-6

Attaching Other Displays .........................................................................................................................C-7

Configuring an External Display in Windows 7 .....................................................................................C-10

NVIDIA Control Panel ...........................................................................................................................C-13

Optimus™ Customization Options .........................................................................................................C-15

Set PhysX® Configuration .....................................................................................................................C-19

Video Settings .........................................................................................................................................C-20

HDMI Audio Configuration ...................................................................................................................C-21

Specifications

Processor ...................................................................................................................................................D-2

Core Logic ................................................................................................................................................D-3

Memory .....................................................................................................................................................D-3

Display ......................................................................................................................................................D-3

Page 30

XXVIII

Preface

Video Adapter Options .............................................................................................................................D-3

Storage ......................................................................................................................................................D-4

BIOS .........................................................................................................................................................D-4

Audio ........................................................................................................................................................D-4

Keyboard & Pointing Device ....................................................................................................................D-4

Interface ....................................................................................................................................................D-4

Slots ..........................................................................................................................................................D-4

Card Reader ..............................................................................................................................................D-5

Communication .........................................................................................................................................D-5

Security .....................................................................................................................................................D-5

Features .....................................................................................................................................................D-5

Power Management ..................................................................................................................................D-5

Power ........................................................................................................................................................D-5

Environmental Spec ..................................................................................................................................D-5

Physical Dimensions & Weight ................................................................................................................D-6

Page 31

Overview 1 - 1

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, card reader), TouchPad & Mouse & Audio Features.

• Chapter 3 The computer’s power management options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Wireless Display, Fingerpr int,

Bluetooth & WLAN Combo and TruStudio Audio modules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the Control Center.

• Appendix C Information on the NVIDIA Video driver controls.

• Appendix D The computer’s specification.

Page 32

1 - 2 Overview

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”

on page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Page 33

Overview 1 - 3

Quick Start Guide

Not Included

Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4

- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your

system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers

& Utilities” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Page 34

1 - 4 Overview

Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 operating system is supported.

Note: In order to run Windows 7 without limitations or decreased performance, your computer requires a mini- mum 1GB of system memory (RAM).

Page 35

Model Differences 1 - 5

Quick Start Guide

Model Differences

This notebook series includes three different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual.

Table 1 - 1 - Model Differences

Feature Model A Model B Model C

CPU Type

Supported

See “Specifications” on page D - 1 for more details

Display Type

Supported

15.6" (39.62cm) FHD (1920 * 1080) 16:9 Backlit Panel

17.3" (43.94cm) FHD (1920 * 1080) 16:9 Backlit Panel

Video Cards

Supported

See “Specifications” on page D - 1 for more details

Keyboard

Keyboard LED Supported (See

pages 1 - 11 to 1 - 13)

Not Applicable

Keyboard LED Supported (See

pages 1 - 11 to 1 - 13)

RAID

Support

Not Applicable RAID Level 0/1 Supported

Power

Supply

Full Range AC adapter 180W, AC in

100~240V, 50~60Hz, DC output

19V, 9.47A

Full Range AC adapter 120W, AC

in 100~240V, 50~60Hz, DC output

19V, 6.3A

Full Range AC adapter 220W, AC

in 100~240V, 50~60Hz, DC output

19V, 11.57A

Page 36

1 - 6 System Startup

Quick Start Guide

System Startup

1. Remove all packing materials, and place the comput er on a stable surface.

2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.

4. Use one hand to raise the

lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);

use the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lift the computer by the lid/LCD).

5. Raise the lid/LCD to a comfortable viewing an gle, a nd p ress the power bu tto n on th e top left of the computer for

about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command from the Start menu in Windows 7. This will help prevent hard disk or system problems.

135

Page 37

Quick Start Guide

System Map: LCD Panel Open - Models A & B 1 - 7

System Map: LCD Panel Open - Models A & B

Figure 1 - 2

LCD Panel Open

1. Built-In PC Camera

2. LCD

3. LED Lock Indicators

4. Power Button

5. Speakers

6. LED Status Indicators

7. Keyboard

8. Built-In Microphone

9. TouchPad and Buttons

10.Fingerprint Reader (Optional)

Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above.



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices (e.g. WLAN or Bluetooth) aboard aircraft is usually prohibited. Make sure any wireless modules are OFF if you are using the computer aboard aircraft.

Use the appropriate function key combination to toggle power to any wireless modules, and check the indicators to see if any modules are powered on or not (see Table 1 - 5, on page 1

- 15/Table 1 - 2, on page 1

- 9).

Note that the keyboard for Models

A & B are different, and only Mod- el A is pictured (see Table 1 - 1,

on page 1 - 5).

Page 38

Quick Start Guide

1 - 8 System Map: LCD Panel Open - Model C

System Map: LCD Panel Open - Model C

Figure 1 - 3

LCD Panel Open

1. Built-In PC Camera

2. LCD

Speakers

LED Indicators

5. Power Button

Keyboard

7. Built-In Microphone

8. TouchPad and Buttons

9. Fingerprint Reader (Optional)

Note that the Touchpad and Buttons valid operational area is that indicated within the red dotted lines above.



Wireless Device

Operation Aboard

Aircraft

Use the appropriate function key combination to toggle power to any wireless modules, and check the indicators to see if any modules are powered on or not (see Table 1 - 5, on

page 1 - 15/Table 1 - 2, on page 1 - 9).

Page 39

System Map: LCD Panel Open - Model C 1 - 9

Quick Start Guide

LED Indicators

The LED indicators display helpful information about the current status of the computer.

*Note: The powered USB 3.0 port (see Figure 1 - 9 on page 1 - 19) may be toggled on /off by means of the Fn + Power Button key combination. When the powered USB port is on it will supply power (for charging devices only, not for operating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with certain devices - see page 8 - 13).

Icon Color Models A&B or C Description Icon Color Description

Blue / White

Number Lock is Activated

Orange The Battery is Charging

Blue / White

Caps Lock is Activated

Blinking Orange

The Battery has Reached Critically

Low Power Status

Blue / White

Scroll Lock is Activated

Green The Battery is Fully Charged

Blue / White Hard Disk Activity Orange AC/DC Power is Plugged In

Blue / White

The (optional) Wireless LAN

Module is Powered On

Blinking Orange* The Powered USB Port is On*

Blue / Orange

The (optional) Bluetooth

Module is Powered On

Green The Computer is On

Table 1 - 2 - LED Indicators

Blinking Green The Computer is in Sleep Mode

Page 40

1 - 10 Keyboard - Models A & C

Quick Start Guide

Keyboard - Models A & C

The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See

Table 1 - 5, on page 1 - 15 for full function key combination details.

Figure 1 - 4 - Keyboard - Models A & C



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.

Num Lk & Scr Lk

Hold down the Fn Key and Scr Lk/Num Lk to enable scroll lock/number lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

ScrLk Key

Fn Key

Keypad

Game Control Keys

NumLk Key



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Page 41

Quick Start Guide

Keyboard LED - Models A & C 1 - 11

Keyboard LED - Models A & C

Press Fn plus the key to toggle the keyboard LED on/off. The keyboard LED may be configured using the Fn + key combination outlined in the table below. In addition press Fn plus the

key to launch the

keyboard backlight application to configure the settings (see overleaf).

Table 1 - 3 - Keyboard LEDs - Models A & C

Keyboard LED Function key Combinations

Fn +

Launch the Keyboard Backlight Application

Fn +

Toggle the Keyboard Backlight On/Off

Fn +

Keyboard LED Illumination Decrease

(for Custom Mode only - see Table 1 - 4, on page 1 - 13)

Fn +

Keyboard LED Illumination Increase

(for Custom Mode only - see Table 1 - 4, on page 1 - 13)

2 3

Page 42

1 - 12 Keyboard LED - Models A & C

Quick Start Guide

Keyboard Backlight Application (Models A & C)

The keyboard Backlight application can be accessed by pressing the Fn plus key. Click the Help button

in the application to display the configuration keys.

• Click the Custom button to display the three sections of the keyboard which may be configured.

• Click a section of the keyboard and the color buttons will be displayed.

• Click a color swatch to apply the color to the selected section when not overridden by any effect applied.

• Click on any of the effect buttons to apply random colors, wave or flashing effects etc (see over).

Figure 1 - 5 - Keyboard Backlight Application

Help Button

Keyboard Sections

Color Swatches

Effects Buttons

Page 43

Keyboard LED - Models A & C 1 - 13

Quick Start Guide

Effects Buttons & Help (Models A & C)

Table 1 - 4 - LED Effects Buttons & Help

LED Effects Buttons

Random Color

Up/Down Wave

Dancing Effect

Breathing (All Colors)

Tempo Beat

Cycle (Colors as Selected in RGB)

Flashing

Custom Mode - Display & Configure

Keyboard Sections & Colors



Illumination Keys

Note that the keyboard illumination (increase/decrease) keys may be used to configure the keyboard LED in Cus- tom Mode only.

Page 44

1 - 14 Keyboard - Model B

Quick Start Guide

Keyboard - Model B

The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See

Table 1 - 5, on page 1 - 15 for full function key combination details.

Figure 1 - 6 - Keyboard - Model B



Other Keyboards

Num Lk & Scr Lk

Hold down the Fn Key and Scr Lk/Num Lk to enable scroll lock/number lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk & ScrLk Keys

Fn Key

Keypad

Game Control Keys



Special Characters

Page 45

Keyboard - Model B 1 - 15

Quick Start Guide

Function Keys & Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Visual indicators (see the table below) are available when the Hot Key driver is installed.

Table 1 - 5 - Function Keys & Visual Indicators

Keys Function/Visual Indicators Keys Function/Visual Indicators

Fn + ~ Play/Pause (in Audio/Video Programs) Fn + Esc Control Center Toggle (see over)

Fn + F1

Touchpad Toggle

Fn +F8/F9

Brightness Decrease/Increase

Fn + F2

Turn LCD Backlight Off

(Press a key to or use Touchpad to turn on)

Fn + F10

PC Camera Power Toggle

Fn + F3

Mute Toggle

Fn + F11

WLAN Power Toggle

Fn + F4 Sleep Toggle Fn + F12

Bluetooth Power Toggle

Fn +F5/F6

Volume Decrease/Increase

Fn + Power

Button

Powered USB 3.0 Port Power Toggle

Fn + F7 Display Toggle

Fn +

Keyboard LED (Models A & C)Toggle

(see page 1 - 13)

See also Table 1 - 2, on page 1 - 9 for Number Lock, Caps Lock and Scroll Lo ck indicators

Page 46

1 - 16 Control Center

Quick Start Guide

Control Center

Press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Control Center gives quick access to frequently used controls and enables you to quickly turn modules on/off.

Table 1 - 6 - Control Center



Control Center

Click on any button to turn any of the modules (e.g. TouchPad, Camera) on/off.

Click on the power conservation modes to switch between Performance, Balanced or Energy Star modes (see page 3 - 10). To remove the Power Conservation Modes screen just click in a blank area of the icon or press a key on the keyboard.

Click on the buttons (or just click and hold the mouse button) to adjust the slider for Brightness/Volume.

Click on Display Switch and click to choose a display mode from the menu (see page C - 12).

Click on K/B LED (for Models A & C only) to adjust the keyboard LED settings (see page 1 - 12).

Page 47

System Map: Front & Rear Views 1 - 17

Quick Start Guide

System Map: Front & Rear Views

Figure 1 - 7

Front View

1. LED Power Indicators

2. Vent/Fan Intake

3. Display Port

4. HDMI-Out Port

5. DVI-Out Port

6. DC-In Jack

7. Security Lock Slot (Model C Only)



HDMI Port

Note that the HDMI Port supports video and audio signals to attached external displays (see

“HDMI Audio Configuration” on page C - 21).

Note that THX TruStudio Pro will be disabled when you are connecting to an external display through an HDMI connection (see “THX TruStudio Pro Audio” on page 7 - 75).

Models A & B

Model C

Page 48

1 - 18 System Map: Right View

Quick Start Guide

System Map: Right View

Figure 1 - 8

Right View

1. Optical Device Drive Bay

2. Headphone Jack

3. Microphone Jack

4. S/PDIF-Out Jack

5. Line-In Jack

6. 1 * USB 2.0 Port

7. Security Lock Slot (Models A & B Only)



USB Ports

Note that the connections to the USB ports only fit one way, do not force them.

3 42 6



USB 2.0 or 3.0 Ports

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

3 42 65

Models A & B

Model C

Page 49

System Map: Left View 1 - 19

Quick Start Guide

System Map: Left View

Figure 1 - 9

Left View

1. Mini-IEEE 1394a

Port

2. RJ-45 LAN Jack

3. 1 * Powered USB

3.0 Port

4. 1 * USB 3.0 Port

5. Combined

eSATA/ USB 3.0 Port

6. Multi-in-1 Card

Reader



Mini-IEEE 1394a

Port

The Mini-IEEE 1394a port only supports SELF POWERED IEEE 1394 devices.



USB 3.0 Ports & Powered USB 2.0 Port

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. Note that the USB 3.0 port requires a driver installation (see “USB 3.0” on page 4 - 7), does not support wake on USB and is not operational under DOS. The powered USB 3.0 port can supply power (for charging devices only, not for operating devices) when the system is off but still powered by the AC/DC adapter plugged into a working outlet, or powered by the battery with a capacity level above 20% (this may not work with certain devices - see page 8 - 13). Toggle power to this port by using Fn + power button.

Multi-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

Models A & B

Model C

Page 50

1 - 20 System Map: Bottom View - Models A & B

Quick Start Guide

System Map: Bottom View - Models A & B

Figure 1 - 10

Bottom View

1. Sub Woofer

2. Fan Outlet/Intake

3. Component Bay

Cover

4. HDD Bay

5. Battery



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 11 for full instructions.

Page 51

System Map: Bottom View - Model C 1 - 21

Quick Start Guide

System Map: Bottom View - Model C

Figure 1 - 11

Bottom View

1. Sub Woofer

2. Fan Outlet/Intake

3. Component Bay

Cover

4. Primary HDD Bay

5. Secondary HDD

Bay

6. Battery



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.



Battery Information

Page 52

1 - 22 Windows 7 Start Menu & Control Panel

Quick Start Guide

Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View to view the control panel icons.

Figure 1 - 12 - Start Menu & Control Panel

Click here to toggle Category View

Page 53

Video Features 1 - 23

Quick Start Guide

Video Features

NVIDIA® Optimus™ Technology

NVIDIA® Optimus™ technology is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. The computer will auto- matically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use.

You can switch display devices, and configure display options, from the Display control panel (in Appearances

and Personalization) in Windows 7 (see over). For more detailed video information see “Video Driver Con-

trols” on page C - 1.

Page 54

1 - 24 Video Features

Quick Start Guide

To access Display (Control Panel) and Screen Resolution in Windows:

1. Click Start and click Control Panel.

2. Click Display (icon) - In the Appearances and Personalization category.

3. Click Adjust Screen Resolution/Adjust resolution.

4. Alternatively you can right-click the desktop and select Screen resolution.

5. Use the dropbox to select the screen Resolution (Figure 1 - 13).

6. Click Advanced settings (Figure 1 - 13) to bring up the Advanced properties tabs.

Figure 1 - 13 - Screen Resolution

Page 55

Video Features 1 - 25

Quick Start Guide

To access the Intel(R) Graphics and Media Control Panel:

1. Click Advanced settings (Figure 1 - 13 on page 1 - 24) in the Display Settings control panel in Windows.

2. Click Graphics Properties (button) (Figure 1 - 14) in the Intel Graphics & Media Control Panel tab.

3. Right-click the desktop and select Graphics Properties from the menu.

4. Click the icon (Figure 1 - 14) in the taskbar and select Graphics Properties from the menu.

5. Access the Intel(R) Graphics and Media Control Panel from the Windows control panel in Classic View.

6. Choose the application mode (Basic, Advanced or Wizard) required.

Figure 1 - 14 - Intel Graphics and Media Control Panel

234

Page 56

1 - 26 Video Features

Quick Start Guide

To access the NVIDIA Control Panel:

1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 15).

2. Double-click the icon (Figure 1 - 15) in the Windows control panel.

Figure 1 - 15 - NVIDIA Control Panel

Page 57

Power Options 1 - 27

Quick Start Guide

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 21 ) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.

Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change plan settings and click Change advanced power settings to access further configuration options.

Pay attention to the instructions on battery care in “Battery Information” on page 3 - 11.

Figure 1 - 16 - Power Options

Page 58

Quick Start Guide

1 - 28

Page 59

Storage Devices, Mouse, & Audio

Overview 2 - 1

Chapter 2: Storage Devices, Mouse, & Audio

Overview

Read this chapter to learn more about the following main features and components of the computer:

•Hard Disk Drive

• Optical Device

• Multi-in-1 Card Reader

• Audio Features

• TouchPad and Buttons/Mouse

Page 60

Storage Devices, Mouse, & Audio

2 - 2 Hard Disk Drive

Hard Disk Drive

The hard disk drive(s) is used to store your data in the computer. The hard disks) can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. The primary hard disk bay is accessible from the bottom of your computer as seen below. Note that only Model A/B is pictured, however the procedure for removing the primary hard disk from Model D is identical.

Further details on removing and inserting the hard disk are available in “Upgrading

the Hard Disk Drive(s)” on page 6 - 6.

Model C/D computers feature a primary and secondary hard disk bay (you may have a second hard disk installed as part of a RAID). See “Removing the Hard Disk

from the Secondary HDD Bay (Model C)” on page 6 - 11.



Power Safety

Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.

Figure 2 - 1

Hard Disk Location

Model A/B Model C

Page 61

Storage Devices, Mouse, & Audio

Optical Device 2 - 3

Optical Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage” on page D - 4). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.



Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Win- dows. Click the Volume icon on the notification area to check the setting.

Peripherals must be connected before you turn on the system.

Figure 2 - 2

Optical Device

123

Page 62

Storage Devices, Mouse, & Audio

2 - 4 Optical Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.



CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.

Page 63

Storage Devices, Mouse, & Audio

Optical Device 2 - 5

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives.

3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control p anel to allow yo u to adjust the regional code.



DVD Region Note

DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Figure 2 - 3

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - Wes t ern Europe, Japan,

South Africa, Middle East & Egypt

• Region 3 - South-East Asia, Taiwan,

South Korea, The Philippines, Indonesia, Hong Kong

• Region 4 - South & Central Amer-

ica, Mexico, Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern

Europe, India & Most of Africa

• Region 6 - China

Page 64

Storage Devices, Mouse, & Audio

2 - 6 Multi-in-1 Card Reader

Multi-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “Card Reader” on page 4 - 7).

Note: Some of these cards require PC adapters that are usually supplied with the cards.



Card Reader Cover

Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.

Push-Push Card

Reader

The card reader features a push-in/pushout card insertion and ejection mechanism. Simply push the card to insert and eject it, however Ms Duo cards require an adapter.

Figure 2 - 4

Left View

1. Card Reader

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

Models A & B

Model C

Page 65

Storage Devices, Mouse, & Audio

Audio Features 2 - 7

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the notification area icon to bring up an audio menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination (see Table 1 - 5, on page 1 - 15).



Volume Adjustment

The sound volume level is set using the volume control within Windows (and the volume function keys on the computer). Click the volume icon in the notification area to check the setting.

Headphone

Configuration

It is recommended that you set the Speaker Configu- ration to Stereo (not to 5.1 or 7.1 Speaker) when listening through headphones in order to maximize audio quality.

Figure 2 - 5

Realtek Audio

Manager

Right-click the icon to access the menu above.

See “HDMI Audio Configuration” on page C - 21 for a description of the audio configuration when connecting an HDMI supported display device. See “THX TruStudio Pro Audio” on page 7 - 75 for more information on the THX TruStudio Pro Audio setup.

Page 66

Storage Devices, Mouse, & Audio

2 - 8 Audio Features

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

)

and make sure you are in

Classic View

2. Click Realtek HD Audio Manager (or right-click the notification area icon and select Sound Manager).

3. Click Microphone Effects (tab) in Microphone (tab), and then click to select Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality.

4. Click OK to close the control panel and save the settings.

Figure 2 - 6

Realtek Audio

Manager -

Recording Setup

Page 67

Storage Devices, Mouse, & Audio

Audio Features 2 - 9

Setup for 5.1 or 7.1 Surround Sound

To setup your system for 5.1 or 7.1 surround sound you will need to connect the audio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out jacks (note: the S/PDIF jack is used for 7.1 surround sound only).

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

)

and make sure you are in

Classic View

2. Click Realtek HD Audio Manager (or right-click the notification area icon and select Sound Manager).

3. Click Speakers (tab) and click Speaker Configuration (tab).

4. Select 5.1 or 7.1 Speaker from the Speaker Configuration pull-down menu.



THX Audio & HDMI

Note that the THX audio effects do not apply to audio generated through an HDMI connection (see page 7 - 79.).

Figure 2 - 7

Speaker

Configuration (7.1)



Auto Popup Dialog

You should enable the auto popup dialog to automatically detect when a device has been plugged-in. If disabled, double-click connector settings and click the box to enable the auto popup detection of plugged-n devices.

Connector Settings

Page 68

Storage Devices, Mouse, & Audio

2 - 10 Audio Features

5. Plug the front speaker cables into the Headphone-Out Jack.

6. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows:

• Line-In Jack = Rear Speaker Out

• Microphone-In Jack = Center/Subwoofer Speaker Out

• S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)

7. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on

page 2 - 9).

8. Click to put a tick in the appropriate box according to the speaker plugged-in (e.g. Rear Speaker Out), and then click OK to save the setting.

9. Click OK to exit Realtek HD Audio Manager.

Figure 2 - 8

Connected Device

Auto Popup

Note: Side Speaker Out is required fo r 7.1 Surround only.

Page 69

Storage Devices, Mouse, & Audio

TouchPad and Buttons/Mouse 2 - 11

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.



Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.

Page 70

Storage Devices, Mouse, & Audio

2 - 12 TouchPad and Buttons/Mouse

Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 7) you can configure the functions from the Mouse control panel in Windows, or by doubleclicking the TouchPad driver icon in the notification area. You may then configure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your preferences. You will find further information at www.synaptics.com.



TouchPad Scrolling

This computer model series may feature different TouchPad versions.

These TouchPads may differ in their vertical scrolling function in most scrollable windows.

Some TouchPads require sliding the finger up and down on the right of the TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the TouchPad to scroll the window.

Figure 2 - 9

Mouse Properties

Page 71

Storage Devices, Mouse, & Audio

TouchPad and Buttons/Mouse 2 - 13

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (action) on the surface of the TouchPad to perform specific actions to manipulate documents, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Click

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (tab) and click Settings.

4. Use the menu tree on the left to access the user configurable settings.



Show Video

You can get a clearer view of the gestures involved by clicking the Show Video option for each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three Fingers Down and Three Finger Flick) in the Device Settings > Settings left tree menu

and click the Show Video button to see the demonstration video.

For more details on any of the gestures see the help in the lower part of the right menu window.

Figure 2 - 10

Mouse Properties -

Device Settings

Page 72

Storage Devices, Mouse, & Audio

2 - 14 TouchPad and Buttons/Mouse

Scrolling

The Two-Finger scrolling feature works in most scrollable windows an d allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight continuous motion).

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel in Windows applications that support CTRL + scroll wheel zoom functionality. Place two fingers on the TouchPad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.

Figure 2 - 11

Scrolling Gesture

Figure 2 - 12

Zooming Gesture

Page 73

Storage Devices, Mouse, & Audio

TouchPad and Buttons/Mouse 2 - 15

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of applications such as browsing the Internet or scrolling through a photo viewer. The Three Fingers Down gesture may be used to launch user-selectable applications.

Figure 2 - 13

Rotating Gesture

Figure 2 - 14

Flick/Press

Gesture

Page 74

Storage Devices, Mouse, & Audio

2-16

Page 75

Power Management

Overview 3 - 1

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows 7 OS.)

Page 76

Power Management

3 - 2 The Power Sources

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button on th e top left of the computer for about 2 - 3 se con ds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 15).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 11.

Page 77

Power Management

Turning On the Computer 3 - 3

Turning On the Computer

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.

Power Button as

Stand by or

Hibernate Button

You can use the OS’s Power Options control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or

“Configuring the Power Buttons” on page 3

- 8 for details).



Shut Down

Note that you should always shut your computer down by choosing the Shut Down command from the bottom right of the Start menu in Windows. This will help prevent hard disk or system problems.

Page 78

Power Management

3 - 4 Power Plans

Power Plans

The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.



Resuming Operation

See Table 3 - 1, on

page 3 - 9 for informa-

tion on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Figure 3 - 1

Power Plan

Advanced Settings

(Win 7)

Page 79

Power Management

Power Plans3-5

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

Figure 3 - 2

Power Plans (Win 7)

Click to Show/Hide additional power plans

Page 80

Power Management

3 - 6 Power-Saving States

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.

If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer do wn before the battery becomes depleted.

Page 81

Power Management

Power-Saving States 3 - 7

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.

Figure 3 - 3

Start Menu Power

Page 82

Power Management

3 - 8 Configuring the Power Buttons

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to a power-saving state. Click Choose what the power buttons do on the left menu in Power Options to bring up the menu.



Password

Protection

It is recommended that you enable a password on wake up in order to protect your data.

However you can disable this setting from the Power Options menu by clicking Require a

password on wakeup

in the left menu, and selecting the options (click

Change settings that are currently unavailable).

Figure 3 - 4

Power Options

Define Power

Buttons

Page 83

Power Management

Configuring the Power Buttons 3 - 9

Resuming Operation

You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo).

Power Status

Icon Color

To Resume

Power Off Off Press the Power Button

Sleep Blinking Green

Press the Power Button

Press the Sleep Button (Fn + F4 Key Combo)

Hibernate

Off (battery)

Press the Power Button

Orange (AC/DC adapter)

Display Turned Off Green Press a Key or Move the Mouse/Touchpad



Closing the Lid

If you have chosen to send the computer to Sleep when the lid is closed, raising the lid will wake the system up.

Table 3 - 1

Resuming Operation



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).

Page 84

Power Management

3 - 10 Configuring the Power Buttons

Power Conservation Modes

This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period of inactivity. Adjust Power Conservation Modes from the Control Center:

1. Press the Fn + Esc key combination to toggle the Control Center on/off.

2. Click either the Performance, Balanced or Energy Star button.

3. Click in a blank area of the icon or press a key on the keyboard to exit Power Conservation Mode without making any changes.



Power Conservation

Modes

The Energy Star setting will result in maximum power saving, but with the possible loss of some performance.

Setting the mode to Bal- ance will give power saving matched with performance.

Performance will give optimum computer performance but with less power conservation.

Figure 3 - 5

Control Center

Page 85

Power Management

Battery Information 3 - 11

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure

3 - 1 on page 3 - 4).

Click the battery icon in the notification area to see the current battery level and charge status.



Low Battery

Warning

When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.

Figure 3 - 6

Battery Icon

(Notification Area) &

Battery Advanced

Settings

Page 86

Power Management

3 - 12 Battery Information

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD

brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or co mmunication applications when they are

not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices.



Windows Mobility

Center

The Windows Mobility Center control panel

provides an easy point of access for information on battery status, power plans used and wireless device status etc.

Figure 3 - 7

Windows Mobility

Center

Page 87

Power Management

Battery Information 3 - 13

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery”

on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 15 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-

tors” on page 1 - 9 for information on the battery charge status, and to “Battery Information” on page 3 - 11 for more information on how to maintain and properly

recharge the battery pack.)

Page 88

Power Management

3 - 14 Battery Information

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances.

• DO NOT expose the battery to fire or high temperatures, it may explode.

• DO NOT connect the metal terminals (+, -) to each other.



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has been d roppe d we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is recommended that you replace your computer battery every two years.



Caution

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Page 89

Power Management

Battery Information 3 - 15

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.

1. Save and close all files and applications.

2. Create a power plan for discharging the battery and set all the options to Never.

Figure 3 - 8

Power Plan Create

Page 90

Power Management

3 - 16 Battery Information

3. Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings.

Figure 3 - 9

Change Plan

Settings / Change

Advanced Power

Settings

Page 91

Power Management

Battery Information 3 - 17

4. Scroll down to Battery and click + to expand the battery options.

5. Choose the options below (click Yes if a warning appears):

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

Figure 3 - 10

Power Options

Advanced Settings -

Battery

Page 92

Power Management

3 - 18 Battery Information

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

Page 93

Drivers & Utilities

What to Install 4 - 1

Chapter 4: Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.

What to Install

The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 3 lists what you need to install and it is very important that the drivers are installed in the order indicated.

Module Driver Installation

The procedures for installing drivers for the PC Camera, WLAN, Fingerprint, and Combination Bluetooth & WLAN modules (you should also install the THX Studio Pro Audio and Intel Rapid Storage Technology drivers as instructed in Chap-

ter 7) are provided in “Modules” on page 7 - 1.



Driver Installation &

Power

When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power source.

Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).

Page 94

Drivers & Utilities

4 - 2 Driver Installation

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Driv- ers (button) to access the Optional driver menu.

Figure 4 - 1 - Drivers Installer Screen 1

Note: If you need to reinstall any driver, you should uninstall the driver first.

1. Check the driver installation order from Table 4 - 1,

on page 4 - 3 (the drivers must be installed in

this order) which is the same as that listed in the

Drivers Installer menu below .

2. Click to select the driver you wish to install, (you should note down the drivers as you install them).

3. Follow the instructions for each individual driver installation procedure as listed on the following pages.

Figure 4 - 2 - Drivers Installer Screen 2

Page 95

Drivers & Utilities

Driver Installation 4 - 3

Table 4 - 1 - Driver Installation

Note that for Intel and 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN & Bluetooth drivers.

Windows 7 SP1 Driver Page Windows 7 SP1 Driver Page

Chipset Page 4 - 6 PC Camera Module Page 7 - 15 Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 23 NVIDIA Video (VGA) Page 4 - 6 Intel® Wireless Display Application Page 7 - 23 LAN Page 4 - 6 Fingerprin t Re ad er Module Page 7 - 48 Card Reader Page 4 - 7 Bluetooth Module Page 7 - 60 TouchPad Page 4 - 7 THX TruStudio Pro Audio Page 7 - 75

Hot Key Page 4 - 7

Intel® Rapid Storage Technology Driver

(required for hard disks in AHCI & RAID modes)

Page 7 - 80

USB 3.0 Page 4 - 7 Intel® Rapid Start Technology Driver Page 7 - 85 MEI Driver Page 4 - 7

Note all drivers provided are for Windows 7 with Service Pack 1

Audio Page 4 - 7

Page 96

Drivers & Utilities

4 - 4 Driver Installation

Manual Driver Installation

Click the Browse CD/DVD button in the Drivers Installer application and browse to the executable file in

the appropriate driver folder.

Windows Update

After installing all the drivers make sure you enable Windows Update in order to get all the latest securi ty updates etc. (all updates will include the latest hotfixes from Microsoft). See “Windows Update” on page 4 -

8 for instructions.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro- grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as outlined in this chapter.

If the driver is not listed in the Programs and Fea- tures menu:

1. Click Start, and click Control Panel (or point to Settings and click Control Panel).

2. Double-click Device Manager (Hardware and Sound > Device Manager).

3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).

4. Click Driver (tab) and click the Update Driver or Uninstall button and follow the on screen prompts.

Page 97

Drivers & Utilities

Driver Installation 4 - 5

User Account Control

If a User Account Control prompt appears as part of the driver installation procedure, click Continue/Al- low, and follow the installation procedure as directed.

Windows Security Message

If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or Install to continue the installation procedure.

You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.

New Hardware Found

If you see the message “New Hardware Found” during the installation procedure (other than when out- lined in the driver install procedure), click Cancel to close the window, and follow the installation procedure.

Page 98

Drivers & Utilities

4 - 6 Driver Installation

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or Option Driv- ers (button) to access the Optional driver menu.

Chipset

1. Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

Video (VGA)

1. Click 2.Install VGA Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

NVIDIA Video (VGA)

1. Click 3.Install nVIDIA VGA Driver > Yes.

2. Click AGREE AND CONTINUE (button) to accept the terms of the license agreement.

3. Click Next > Next.

4. Click the REST ART NOW button to restart the computer.

Note: After installing the video driver go to the Display/Display Settings control panel to adjust the vid-

eo settings to the highest resolution.

LAN

1. Click 4.Install LAN Driver > Yes.

2. Click Next > Install.

3. Click Finish.



Driver Installation General Guidelin es

The driver installation procedure outlined in this Chapter (and in Chapter 7 Options & Modules), are accurate at the time of going to press.

Drivers are always subject to upgrade and revision so the exact procedure for certain drivers may differ slightly. As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a restart is required to install the driver.

Page 99

Drivers & Utilities

Driver Installation 4 - 7

Card Reader

1. Click 5.Install Cardreader Driver > Yes.

2. Click Finish.

TouchPad

1. Click 6.Install Touchpad Driver > Yes.

2. Click Next.

3. Click the button to accept the license, and then

click Next.

4. Click Finish > Restart Now to restart the com-

puter.

Hot Key

1. Click 7.Install Hotkey AP > Yes.

2. Click Next > Next.

3. Click Finish > Finish to restart your computer.

USB 3.0

1. Click 8.Install USB 3.0 Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

MEI Driver

1. Click 9.Install MEI Driver > Yes.

2. Click Next > Yes > Next.

3. Click Finish.

Audio

1. Click 10. Install Audio Driver > Yes.

2. Click Next.

3. Click Finish to restart the computer.

After installing the audio driver the system will not return to the Drivers Installer screen. To install any of the optional drivers, eject the Device Drivers & Utili- ties + User’s Manual disc and then reinsert it (or double-click the disc icon in My Computer), and click Option Drivers (button) to access the optional driver menu.

Page 100

Drivers & Utilities

4 - 8 Driver Installation

It is recommended that you install the THX Tru Studio Pro Audio application (see “THX TruStudio AP

Installation” on page 7 - 75) and Intel Rapid Storage

Technology driver (see “IRST Driver Installation”

on page 7 - 9 - required for AHCI & RAID mode).

Windows Experience Index

After Video (VGA) driver has been installed, and the system restarted, the OS will automatically run the "Winsat.exe" to rate the performance. If you have restarted the system during this time then follow the instructions below to update the information.

After the drivers are installed follow this procedure to ensure an accurate rating from the Windows Experi- ence Index (make sure the AC/DC adapter is plugged in):

1. Click Start, and click Control Panel.

2. Click Performance Information and Tools (System and Security > System > Check the Windows Experience Index).

3. Click “Rate this computer/Refresh Now/Re- run the assessment”.

4. The computer will take a few minutes to assess the system performance.

5. Close the control panel.



Windows Update

After installing all the drivers make sure you enable Windows Update in order to get all the latest security updates etc. (all up-

dates will include the latest hotfixes from Microsoft).

To enable Windows Update make sure you are connected to the internet:

1. Click Start, and click Control Panel (or point to Settings and click Control Panel).

2. Click Windows Update (System and Security/Security).

3. Click Check for updates (button).

4. The computer will now check for updates (you need to be connected to the internet).

5. Click Install now (button) to begin checking for the updates.

6. Click Install updates (button) to install the updates.