Clevo P150HM, P151HM1, P170HM, P170HM3 User guide

V11.6.12

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©June 2011

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

I

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc­tive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux­embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland,
United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov­enia.

EuP-Standby and Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC)
regulations on power consumption in off mode or standby mode:

• Standby Mode < 2W

• Off Mode < 1W

II

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has at­tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies
to products regulated by certain European health, safety and environmental protection legislation. The CE Mark
is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his
product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE
Marking. A notified body has determined that this device has properly demonstrated that the requirements of the
directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the
notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product.
Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc ed radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference.
And

2. This device must accept any interference, including interfer ence that may cause undesired operation of the

device.

IV

Preface



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.

V

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit:

• Model A - Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 9.47A (180W) minimum.

• Model B - Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 6.3A (120W) minimum.

• Models C & D - Full Range AC/DC Adapter - AC Input 100 - 240V, 50 - 60Hz, DC Output 19V, 11.57A (220W)

minimum.

This Computer’s Optical Device is a Laser Class 1 Product

VI

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer
to any shock or vibration.

Do not place it on an unstable
surface.

Do not place anything heavy
on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.

Do not expose it to excessive

heat or direct sunlight.

Do not leave it in a place where

foreign matter or moisture may

affect the system.

Don’t use or store the computer

in a humid environment.

Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until
you properly shut down all pro­grams.

Do not turn off any peripheral
devices when the computer is
on.

5. Take care when using peripheral devices.

Use only approved brands of
peripherals.

VIII

Do not disassemble the com­puter by yourself.

Unplug the power cord befor e
attaching peripheral devices.

Perform routine maintenance
on your computer.

Power Safety



Power Safety

Warning

Before you undertake
any upgrade proce­dures, make sure that
you have turned off the
power, and discon­nected all peripherals
and cables (including
telephone lines). It is
advisable to also re­move your battery in
order to prevent acci­dentally turning the
machine on.

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a

steady , uninterru pted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third

prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not

by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current

load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power

supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power
cord if you are wet.

Do not use the power cord if
it is broken.

Do not place heavy objects
on the power cord.

Preface

IX

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides
the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha-

nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-

ture environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

X

General Battery Precautions



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu al-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

Preface

XI

Preface



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before turning the computer on.

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

XII

Preface



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or req uire proof of ownersh ip for both hard -

ware and software. Make sure your “papers” are handy.

XIII

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock­ing the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com­puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.

XIV

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the

level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on

a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles

when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent

and short breaks are better than fewer and longer breaks.

XV

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

Cable TV Safety

If you have included a TV Tuner in your purchase option then pay careful attention to the following:

• Make sure that your CATV system installer has connected the Coaxial cable shield to the grounding system of the

building, as close to the point of cable entry as practical.

• This reminder is provided to call the CATV system installer’s attention to Article 820-93 of the NEC (Section 54, Part

I of the Canadian Electrical Code).

• The TV antenna supplied with any TV Tuner module is intended for indoor use only. Please do not use your TV Tuner

module outdoors.

XVI

Preface

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive.
Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp
edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated
logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during
transport. If any such wear and tear develops contact your service center.

XVII

Preface

XVIII

Contents

Notice .................................................................................I

EuP-Standby and Off Mode Power Consumption State-

ment: .................................................................................II

FCC Statement ................................................................IV

FCC RF Radiation Exposure Statement: ......................... V

Instructions for Care and Operation ..............................VII

Power Safety ...................................................................IX

Polymer Battery Precautions ........................................... X

General Battery Precautions ...........................................XI

Cleaning .........................................................................XII

Servicing ........................................................................XII

Travel Considerations .................................................. XIII

Quick Start Guide

Overview ........................................................................1-1

Advanced Users .............................................................1-2

Beginners and Not-So-Advanced Users ........................1-2

Warning Boxes ..............................................................1-2

Not Included ..................................................................1-3

System Software ............................................................1-4

Model Differences .........................................................1-5

System Startup ...............................................................1-6

System Map: LCD Panel Open - Models A & B ...........1-7

Preface

System Map: LCD Panel Open - Models C & D ...........1-8

LED Indicators ...............................................................1-9

Keyboard ......................................................................1-10

Function Keys & Visual Indicators .............................1-11

System Map: Front & Rear Views ...............................1-12

System Map: Right View .............................................1-13

System Map: Left View ...............................................1-14

System Map: Bottom View - Models A & B ...............1-15

System Map: Bottom View - Models C & D ...............1-16

Windows 7 Start Menu & Control Panel .....................1-17

Video Features .............................................................1-18

Screen Resolution ........................................................1-19

NVIDIA Control Panel ................................................1-20

Catalyst Control Center ...............................................1-21

Power Options ........................................ .... ..................1-22

Storage Devices, Mouse, Audio &
Printer

Overview ........................................................................2-1

Hard Disk Drive .............................................................2-2

Optical Device ...............................................................2-3

Loading Discs ................................................................2-3

Handling CDs or DVDs .................................................2-4

XIX

Preface

DVD Regional Codes ....................................................2-5

Multi-in-1 Card Reader ..................................................2-6

Audio Features ...............................................................2-7

Setup for Audio Recording ............................................2-8

Setup for 5.1 or 7.1 Surround Sound .............................2-9

Audio Notes for Model C/D Computers (Fn + 5) .......2-11

TouchPad and Buttons/Mouse .....................................2-12

Gestures and Device Settings ......................................2-14

Adding a Printer ...........................................................2-17

USB Printer ..................................................................2-17

Install Instructions: ......................................................2-17

Parallel Printer .............................................................2-17

Power Management

Overview ........................................................................3-1

The Power Sources ........................................................3-2

AC/DC Adapter .............................................................3-2

Battery ............................................................................3-2

Turning On the Computer ..............................................3-3

Power Plans ...................................................................3-4

Power-Saving States ......................................................3-6

Sleep ..............................................................................3-6

Hibernate ........................................................................3-7

Shut down ......................................................................3-7

Configuring the Power Buttons .....................................3-8

Resuming Operation ......................................................3-9

Battery Information ......................................................3-10

Conserving Battery Power ...........................................3-11

Battery Life ..................................................................3-12

New Battery .................................................................3-12

Recharging the Battery with the AC/DC Adapter .......3-12

Proper handling of the Battery Pack ............................3-13

Battery FAQ .................................................................3-14

Drivers & Utilities

What to Install ........................................................... .....4-1

Module Driver Installation .............................................4 -1

Driver Installation ..........................................................4-2

Manual Driver Installation ............................................. 4 -4

Updating/Reinstalling Individual Drivers ......................4-4

User Account Control ....................................................4-5

Windows Security Message ...........................................4-5

New Hardware Found ....................................................4-5

Driver Installation Procedure ......................................... 4-6

Chipset ...........................................................................4-6

Video (VGA) - NVIDIA ................................................4-6

Video (VGA) - AMD .....................................................4-6

LAN ...............................................................................4-7

Card Reader ...................................................................4-7

TouchPad .......................................................................4-7

XX

Preface

Hot Key ..........................................................................4-7

USB 3.0 ..........................................................................4-7

MEI Driver .....................................................................4-8

Audio .............................................................................4-8

Windows Experience Index ...........................................4-9

Optional Drivers ..........................................................4-10

PC Camera ...................................................................4-11

Wireless LAN ...................................... ........................4-11

Fingerprint Reader Module ..........................................4-11

3.75G/HSPA Module (Models A & B Only) ..............4-11

Consumer Infrared (for TV Tuner Remote -

Models C & D Only) ...................................................4-11

THX TruStudio AP ......................................................4-11

Intel Rapid Storage Technology Driver .......................4-11

BIOS Utilities

Overview ........................................................................5-1

The Power-On Self Test (POST) ................................... 5-2

Failing the POST ...........................................................5-3

Fatal Errors ....................................................................5-3

Non-Fatal Errors ............................................................5-3

The Setup Utility .................................................. ..........5-4

Entering Setup ...............................................................5-4

Setup Screens .................................................................5-5

Main Menu .....................................................................5-6

System Time & Date (Main Menu) ...............................5-6

SATA Port # (Main Menu) ............................................5-7

System/Extended Memory: (Main Menu) .....................5-7

MB Series / BIOS Revision / KBC/
EC firmware Revision / VGA Card etc. (Main Menu) ..5-7

Advanced Menu .............................................................5-8

Advanced Chipset Control (Advanced Menu) ...............5-8

Bluetooth Power Setting (Advanced Menu >

Advanced Chipset Control) ...........................................5-9

SATA Mode (Advanced Menu) ....................................5-9

Legacy USB Support: (Advanced Menu) ......................5-9

Boot Logo: (Advanced Menu) .....................................5-10

Power On Boot Beep (Advanced Menu) .....................5-10

Battery Low Alarm Beep: (Advanced Menu) ..............5-10

Security Menu ..............................................................5-11

Set Supervisor Password (Security Menu) ..................5-11

Boot Menu ...................................................................5-13

Boot Sequence (Boot Menu) ........................................5-14

Exit Menu ....................................................................5-15

Upgrading The Computer

Overview ........................................................................6-1

When Not to Upgrade ....................................................6-2

Removing the Battery ....................................................6-3

Upgrading the Optical Device (Model A/B) ..................6-4

XXI

Preface

Upgrading the Optical Device (Model C/D) .................6-5

Upgrading the Hard Disk Drive(s) ................................6-6

Upgrading the System Memory (RAM) ......................6-16

Replacing the Primary System Memory Modules .......6-17

Modules

Overview ........................................................................7-1

Setting Up SATA RAID Mode ......................................7-2

AHCI Mode ...................................................................7-2

RAID ..............................................................................7-2

Intel® Rapid Storage Technology Application .............7-2

SATA RAID Setup Procedure (BIOS) ..........................7-4

RAID Setup (Intel Matrix) .............................................7-5

Intel Rapid Storage Technology ....................................7-8

IRST Driver Installation ................................................7-8

RAID Volume Data Verification and Repair ..............7-11

Replacing and Reverting Recovery and

Master Volumes ...........................................................7-11

PC Camera Module ......................................................7-14

PC Camera Driver Installation .....................................7-15

PC Camera Audio Setup ..............................................7-16

Wireless LAN Module .................................................7-22

Intel® Wi-Fi Link Series Driver Installation ...............7-23

802.11b/g/n Driver Installation ....................................7-23

Connecting to a Wireless Network in Windows 7 .......7-24

Intel® My WiFi Configuration ....................................7-27

Intel WLAN & Bluetooth Combo Module

High-Speed Data Transfer Configuration ....................7-39

Windows Mobility Center ...........................................7-41

Fingerprint Reader Module ..........................................7-42

Fingerprint Reader Driver Installation .........................7-43

User Enrollment ...........................................................7-44

Fingerprint Control Center Features ............................7-47

Bluetooth Module ........................................................7-48

3rd Party Bluetooth Combo Driver Installation ...........7-49

3rd Party Bluetooth & WLAN Combo Settings ..........7-50

3rd Party Bluetooth Networking Setup ........................7-53

3rd Party Bluetooth & WLAN Combo Module

Configuration ...............................................................7-54

Intel Bluetooth Combo Driver Installation ..................7-57

Standard Bluetooth Configuration in Windows 7 ........7-58

3.75G/HSPA Module ...................................................7-62

3.75G/HSPA Module USIM Card Installation ............7-63

BandLuxe HSDPA Utility ...........................................7-66

BandLuxe HSDPA Utility Installation ........................7-66

BandLuxe HSDPA - Connection Manager ..................7-67

Creating a Profile .........................................................7-70

Choosing a Profile .......................................................7-73

Editing a Profile ...........................................................7-74

Text Messaging Service (SMS) ...................................7-75

XXII

Preface

Setting ..........................................................................7-78

Statistics & Information ...............................................7-84

Wireless Manager .................................... ....................7-85

Wireless Manager Installation .....................................7-85

Wireless Manager Application ....................................7-86

Profiles .........................................................................7-89

Settings ........................................................................7-93

Text Messaging Service (SMS) ...................................7-96

SMS Utility ..................................................................7-96

Sending a Text Message ..............................................7-98

Phonebook .................................................................7-101

SMS Settings ............................................... ..............7-104

TV Tuner Module ......................................................7-107

Consumer Infrared Driver ..........................................7-108

Digital TV Broadcast Signal ......................................7-109

TV Recording and Power Plans ................................. 7-109

Remote Control Unit ..................................................7-109

THX TruStudio Pro Audio ........................................7-110

THX TruStudio AP Installation .................................7-110

THX TruStudio Pro Activation .................................7-111

THX TruStudio Pro Application ...............................7-111

Troubleshooting

Overview ........................................................................8-1

Basic Hints and Tips ......................................................8-2

Backup and General Maintenance .................................8-3

Viruses ...........................................................................8-4

Upgrading and Adding New Hardware/Software .......... 8-5

Problems & Possible Solutions ......................................8-7

Bluetooth Connection Problems ..................................8-13

Intel® WLAN & Bluetooth V3.0+HS

Combo Modules ...........................................................8-17

Installing Windows 7 (pre Service Pack 1) for

RAID Systems with Advanced Format Disks .............8-18

Interface (Ports & Jacks)

Overview .......................................................................A-1

Ports and Jacks ..............................................................A-2

Card Reader ..................................................................A-2

Cable (CATV) Antenna Jack (Models C & D Only) ....A-2

Consumer Infrared Transceiver ....................................A-2

DC-In Jack ..................................... ...............................A-2

DVI-Out Port ................................................................A-2

e-SATA / USB 2.0 Combo Port ....................................A-3

HDMI-Out Port .............................................................A-3

Headphone-Out Jack .....................................................A-3

Line-In Jack ..................................................................A-3

Microphone-In Jack ......................................................A-3

Mini-IEEE 1394a Port ..................................................A-4

RJ-45 LAN Jack ............................................................A-4

XXIII

Preface

S/PDIF-Out Jack ...........................................................A-4

Security Lock Slot ........................................................A-4

USB 2.0/1.1 Ports .........................................................A-5

USB 3.0 Port .................................................................A-5

NVIDIA Video Driver Controls

NVIDIA Video Driver Installation ...............................B-1

NVIDIA Control Panel (Win 7) ...................................B-2

Display Devices ............................................................B-5

Display Modes ..............................................................B-6

Attaching Other Displays (Win 7) ..............................B-10

NVIDIA 3D Shutter Glasses Kit ................................B-18

AMD Video Driver Controls

Video Driver Installation ..............................................C-1

Video (VGA) ................................................................C-1

Catalyst™ Control Center ............................................C-2

Catalyst™ Control Center Preferences .........................C-3

Display Devices & Options ..........................................C-7

Configuring an External Display In the CCC ...............C-8

Configuring an External Display In Windows 7 .......C-12

HDMI Audio Configuration .......................................C-16

Specifications

Processor ....................................................................... D-2

Processor .......................................................................D-2

Core Logic ....................................................................D-2

Memory .........................................................................D-2

Display ..........................................................................D-3

Video Adapter Options .................................................D-3

Video Adapter Options .................................................D-3

Video Adapter Options .................................................D-4

Video Adapter Options .................................................D-4

Storage ..........................................................................D-4

BIOS .............................................................................D-4

Audio ............................................................................D-5

Keyboard & Pointing Device ........................................D-5

Interface ........................................................................D-5

Interface ........................................................................D-5

Slots ..............................................................................D-5

Card Reader ..................................................................D-5

Communication ............................................................. D-6

Communication ............................................................. D-6

Security .........................................................................D-6

Operating System ..........................................................D-6

Power Management ......................................................D-6

Power ............................................................................D-6

Power ............................................................................D-7

Environmental Spec ......................................................D-7

Physical Dimensions & Weight .................................... D-7

XXIV

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, card reader), TouchPad & Mouse, Audio Features & Printer.

• Chapter 3 The computer’s power management options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Fingerprint, Bluetooth & WLAN

Combo and 3.75G modules (some of which may be optional depending on your purchase configu-
ration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the NVIDIA Video driver controls.

• Appendix C The computer’s specification.

1

Overview 1 - 1

1



Notes

Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”

on page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4

- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your

system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers

& Utilities” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to com­municate with external devices, connect to the internet etc.

Not Included

Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs)
have their own manuals, so please consult the appropriate manuals.

1

Overview 1 - 3

1

Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the Windows 7 operating system is sup­ported.

Note: In order to run Windows 7 without limitations or decreased performance, your computer requires a mini-
mum 1GB of system memory (RAM).

1 - 4 Overview

Quick Start Guide

Model Differences

This notebook series includes three different model types that mainly differ as indicated in the table below. Note that
your model may appear slightly different from those pictured in this manual.

Feature Model A Model B Model C Model D

1

Case Color

CPU Type

Supported

Core Logic

Display Type

Supported

Video Cards

Supported

Power

Supply

Rubber Style Paint Standard Paint

See “Specifications” on page D - 1 for more details

Intel® HM65 Chipset Intel® HM67 Chipset

15.6" (39.62cm) FHD

(1920 * 1080) 16:9 Panel

Full Range AC adapter

180W, AC in 100~240V,

50~60Hz, DC output 19V ,

9.47A

15.6" (39.62cm) HD+

(1600 * 900) 16:9 Panel

15.6" (39.62cm) FHD

(1920 * 1080) 16:9 Panel

See “Specifications” on page D - 1 for more details

Full Range AC adapter

120W, AC in 100~240V,

50~60Hz, DC output 19V,

6.3A

17.3" (43.94cm) FHD (1920 * 1080) 16:9 Panel
(Model D supports 3D Shutter Glasses Kit

Full Range AC adapter 220W, AC in 100~240V,

50~60Hz, DC output 19V, 11.57A

- see page B - 18)

Table 1 - 1 - Model Differences

See “Specifications” on page D - 1 for more details (note that only Model C/D supports RAID level 0/1).

Model Differences 1 - 5

1



Shutdown

Note that you should al­ways shut your computer
down by choosing the
Shut Down command
from the Start menu in
Windows 7. This will
help prevent hard disk or
system problems.

135

Quick Start Guide

System Startup

1. Remove all packing materials, and place the comput er on a stable surfac e.

2. Securely attach any peripherals you want to use with the n otebook (e.g. keyboard and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack at th e rear of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.

4. Use one hand to raise the
the other hand (as illustrated in Figure 1 - 1 below) to support the base of the computer (Note: Never lif t the
computer by the lid/LCD).

5. Raise the lid/LCD to a comfortable viewing an gle, a nd pre ss the power bu tton on th e top left of the computer for

about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn
from orange to green when the computer powers on).

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD

1 - 6 System Startup

lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);

use

System Map: LCD Panel Open - Models A & B

Figure 1 - 2

LCD Panel Open

1. Built-In PC Camera

2. LCD

3. LED Lock Indicators

4. Power Button

5. Speakers

6. LED Status Indicators

7. Keyboard

8. Built-In Microphone

9. TouchPad and
Buttons

10.Fingerprint Reader
(Optional)

Note that the Touchpad and
Buttons valid operational area
is that indicated within the red
dotted lines above.

2

1

8

9

7

3



Wireless Device

Operation Aboard

Aircraft

The use of any portable
electronic transmission de­vices (e.g. WLAN or Blue­tooth) aboard aircraft is
usually prohibited. Make
sure any wireless modules
are OFF if you are using
the computer aboard air­craft.

Use the appropriate func­tion key combination to
toggle power to any wire­less modules, and check
the indicators to see if any
modules are powered on or
not (see Table 1 - 4, on

page 1 - 11/Table 1 - 2, on
page 1 - 9).

6

5

4

5

10

Quick Start Guide

1

System Map: LCD Panel Open - Models A & B 1 - 7

1

Figure 1 - 3

LCD Panel Open

1. Built-In PC Camera

2. LCD

3.

Speakers

4.

LED Indicators

5. Power Button

6.

Keyboard

7. Built-In Microphone

8. TouchPad and
Buttons

9. Fingerprint Reader
(Optional)

10. 3D Emit te r (

Model D

)

Note that the Touchpad and
Buttons valid operational area
is that indicated within the red
dotted lines above.

2

1

8

9

7

3



Wireless Device

Operation Aboard

Aircraft

The use of any portable
electronic transmission de­vices (e.g. WLAN or Blue­tooth) aboard aircraft is
usually prohibited. Make
sure any wireless modules
are OFF if you are using
the computer aboard air­craft.

Use the appropriate func­tion key combination to
toggle power to any wire­less modules, and check
the indicators to see if any
modules are powered on or
not (see Table 1 - 4, on

page 1 - 11/Table 1 - 2, on
page 1 - 9).

6

5

4

3

10

Quick Start Guide

1 - 8 System Map: LCD Panel Open - Models C & D

System Map: LCD Panel Open - Models C & D

LED Indicators

The LED indicators display helpful information about
the current status of the computer.

Icon

Color Models

A & B

Blue White

Blue White

Blue White

Blue White Hard Disk Activity

Color

Model C

Description

Number Lock is

Activated

Caps Lock is

Activated

Scroll Lock is

Activated

Quick Start Guide

Icon Color Description

Orange The Battery is Charging

Blinking

Orange

Green The Battery is Fully Charged

Orange AC/DC Power is Plugged In

Blinking

Orange*

Green The Computer is On

Blinking

Green

The Battery has Reached

Critically Low Power Status

AC/DC Power is Plugged In and

the Powered USB Port is On*

The Computer is In Sleep Mode

1

The (optional)

Blue White

Blue Orange

Wireless LAN

Module is Powered

On

The (optional)

Bluetooth Module is

Powered On

Table 1 - 2 - LED Lock & Status Indicators

Table 1 - 3 - LED Power Indicators

*Note: The powered USB 2.0 port (see Figure 1 - 7 on

page 1 - 14) may be toggled on /off by means of the Fn

+ Power Button key combination. When the powered

USB port is on it will supply power when the system
is off but still powered by the AC/DC adapter plugged
into a working outlet (this may not work with certain
devices - see page 8 - 12).

System Map: LCD Panel Open - Models C & D 1 - 9

1



Other Keyboards

If your keyboard is dam­aged or you just want to
make a change, you can
use any standard USB
keyboard. The system will
detect and enable it auto­matically. However spe­cial functions/hot-keys
unique to the system’s
regular keyboard may not
work.

Num Lk & Scr Lk

Hold down the Fn Key
and Scr Lk/Num Lk to en­able scroll lock/number
lock, and check the LED
indicator for status.

Numerical

Play/Pause Key

Function Keys

NumLk &
ScrLk Keys

Fn Key

Keypad

Game Control Keys

Toggle Key (Models A & B)

3.75G/HSPA Module
Power



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters.
These special characters can only be produced by using the numeric keypad. Regular number keys (in
the upper row of the keyboard) will not work. Make sure that NumLk is on.

Quick Start Guide

Keyboard

The keyboard has an embedded numerical keypad for easy numeric data input, and
features function keys to allow you to change operational features instantly. See

1 - 10 Keyboard

Table 1 - 4, on page 1 - 11 for full function key combination details.

Figure 1 - 4 - Keyboard

Quick Start Guide

Function Keys & Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition
to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key
driver is installed. After installing the driver an icon will appear in the notification area.

Keys Function/Visual Indicators Keys Function/Visual Indicators

Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F7 Display Toggle

Fn +

3.75G Module Power

Toggle (Models A & B

Only)

Fn +F8/F9

Brightness Decrease/

Increase

1

Fn + F1 Touchpad Toggle Fn + F10

Fn + F2

Fn + F3 Mute Toggle Fn + F12

Fn + F4 Sleep Toggle Fn + NumLk Number Lock Toggle

Fn +F5/F6

Fn + 5

(Press a key to or use Touchpad to turn on)

Volume Decrease/

(Model C Only) Audio Toggle - Toggle between

Standard & Enhanced Audio

Turn LCD Backlight Off

Increase

(see page 2 - 9)

Fn + F11

Fn + ScrLk Scroll Lock Toggle

Fn + Power

Button

PC Camera Power

Toggle

WLAN Module Power

Toggle

Bluetooth Module

Power Toggle

Powered USB 2.0 Port Power Toggle

Table 1 - 4 - Function Keys & Visual Indicators

Keyboard 1 - 11

1

Figure 1 - 5

Front View

1. LED Power Indica­tors

2. Vent/Fan Intake

3. eSATA/USB 2.0
Combo Port

4. HDMI-Out Port

5. DVI-Out Port

6. DC-In Jack

7. Security Lock Slot
(Models C & D
Only)

8. Consumer Infrared
Transceiver
(Models C & D Only
for Optional TV
Tuner)

1

3

4

6

2

5

2



HDMI Port

Note that the HDMI Port supports video and audio signals to attached external displays (see

“HDMI Audio Configuration” on page B - 13).

Note that THX TruStudio Pro will be disabled when you are connecting to an external display
through an HDMI connection (see “THX TruStudio Pro Audio” on page 7 - 110).

Models A & B

Models A & B

1

3

4

6

2

5

2

Models C & D

7

8

Models C & D

Quick Start Guide

System Map: Front & Rear Views

1 - 12 System Map: Front & Rear Views

System Map: Right View

Figure 1 - 6

Right View

1. Optical Device
Drive Bay

2. Headphone Jack

3. Microphone Jack

4. S/PDIF-Out Jack

5. Line-In Jack

6. 1 * USB 2.0 Port

7. Security Lock Slot
(Models A & B
Only)



USB Ports

Note that the connections
to the USB ports only fit
one way, do not force
them.

1

3 42 6

7

5



USB 2.0 or 3.0 Ports

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black.

1

3 42 65

Models A & B

Models C & D

Quick Start Guide

1

System Map: Right View 1 - 13

1

Figure 1 - 7

Left View

1. RJ-45 LAN Jack

2. 2 * USB 3.0 Ports

3. 1 * Powered USB

2.0 Port

4. Mini-IEEE 1394a

Port

5. Multi-in-1 Card

Reader

6. CATV Antenna

Jack (Model C
Only for TV Tuner
Option)



Mini-IEEE 1394a

Port

The Mini-IEEE 1394a
port only supports SELF
POWERED IEEE 1394
devices.

1

2

3

4

5



USB 3.0 Ports & Powered USB 2.0 Port

USB 3.0 ports are denoted by their blue color; USB 2.0 ports are colored black. Note that the USB

3.0 port requires a driver installation (see “USB 3.0” on page 4 - 7), does not support wake on
USB and is not operational under DOS. The powered USB 2.0 port can supply power when
the system is off but still powered by the AC/DC adapter plugged into a working outlet ( thi s ma y

not work with certain devices - see page 8 - 12). Toggle power to this port by using Fn + power
button.

Multi-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

MS (Memory Stick) / MS Pro / MS Duo

3

2

Models A & B

1

2

3

4

5

2

6

Models C & D

Quick Start Guide

System Map: Left View

1 - 14 System Map: Left View

System Map: Bottom View - Models A & B

Figure 1 - 8

Bottom View

1. Sub Woofer

2. Fan Outlet/Intake

3. Component Bay
Cover

4. HDD Bay

5. Battery



Overheating

To prevent your comput­er from overheating make
sure nothing blocks the
vent(s)/fan intake(s)
while the computer is in
use.

1

2

4

5



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial dis­charges. See “Battery Information” on page 3 - 10 for full instructions.

3

2

2

2

Quick Start Guide

1

System Map: Bottom View - Models A & B 1 - 15

1

Figure 1 - 9

Bottom View

1. Sub Woofer

2. Fan Outlet/Intake

3. Component Bay

Cover

4. Primary HDD Bay

5. Secondary HDD

Bay

6. Battery

7. Speakers



Overheating

To prevent your comput­er from overheating make
sure nothing blocks the
vent(s)/fan intake(s)
while the computer is in
use.

1

2

4

5



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 30 days or after about 20 partial dis­charges. See “Battery Information” on page 3 - 10 for full instructions.

3

2

2

2

6

7667

7

Quick Start Guide

System Map: Bottom View - Models C & D

1 - 16 System Map: Bottom View - Models C & D

Quick Start Guide

Figure 1 - 10 - Start Menu & Control Panel

Click here to toggle Category View

Windows 7 Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac­cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu
icon , and then select Properties if you want to customize the appearance of the Start menu.

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows 7 provides basic controls for many of the features,
however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all
controls it may be necessary to toggle off Category View to view the control panel icons.

Windows 7 Start Menu & Control Panel 1 - 17

1

1

1

2



NVIDIA & AMD Video Controls

More detailed video controls are provided by the NVIDIA Con trol Pane l or Catalyst Control Center. For more detailed
information see “NVIDIA Control Panel” on page 1 - 20/“Catalyst Control Center ” on page 1 - 21 and Appendix B/

Appendix C.

You can also access the control panels by right-clicking the desktop and selecting NVIDIA Control Panel (Figure 1 - 12

on page 1 - 20) or Catalyst Control Center (Figure 1 - 13 on page 1 - 21).

Quick Start Guide

Video Features

This computer features two different (either AMD or NVIDIA) video options. You can switch display devices,
and configure display options, from the Display control panel (in Appearances and Personalization) in Win-
dows 7.

To access Display (Control Panel) and Screen Resolution in Windows:

1. Click Start and click Control Panel.

2. Click Display (icon) - In the Appearances and Personalization category.

3. Click Adjust Screen Resolution/Adjus t resolution.

OR

4. Alternatively you can right-click the desktop and select Screen resolution (Figure 1 - 11 on page 1 - 19).

5. Use the dropbox to select the screen Resolution (Figure 1 - 11 on page 1 - 19).

1 - 18 Video Features

Screen Resolution

2



Video Options

Note that card types, specifica­tions and drivers are subject to
continual updates and changes.
Check with your service center
for the latest details on video
cards supported.

1

Quick Start Guide

1

Figure 1 - 11 - Screen Resolution

Video Features 1 - 19

1

1

2

2

1

Quick Start Guide

NVIDIA Control Panel

You can access the NVIDIA Control Panel as follows:

1. Click

2. Click NVIDIA Control Panel (Figure 1 - 12) - In the Appearances and Personalization category.

3. See “NVIDIA Video Driver Controls” on page B - 1 for full details on control panels etc.

4. You can also access the control panel by right-clicking the desktop and selecting NVIDIA Control Panel .

OR

Start

, and click

Control Panel

.

Figure 1 - 12 - NVIDIA Control Panel

1 - 20 Video Features

Quick Start Guide

1

2

1

Right-Click
for Menu

2

Catalyst Control Center

You can access the CatalystTM Control Center as follows:

1. Right-click the desktop and select Catalyst Control Center (Figure 1 - 13).
OR

2. Double-click the icon (Figure 1 - 13) in the Windows notification area (or right-click the icon and select
Catalyst Control Center).

3. See “AMD Video Driver Controls” on page C - 1 for full details on control panels etc.

1

Figure 1 - 13 - Catalyst Control Center Access

Video Features 1 - 21

1

Quick Start Guide

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.

Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change plan settings and click Change advanced power settings to access further con­figuration options.

Pay attention to the instructions on battery care in “Battery Information” on page 3 - 10.

1 - 22 Power Options

Figure 1 - 14 - Power Options

Storage Devices, Mouse, Audio & Printer

Chapter 2: Storage Devices, Mouse, Audio & Printer

Overview

Read this chapter to learn more about the following main features and components
of the computer:

•Hard Disk Drive

• Optical Device

• Multi-in-1 Card Reader

• Audio Features

• TouchPad and Buttons/Mouse

• Adding a Printer

2

Overview 2 - 1

Storage Devices, Mouse, Audio & Printer



Power Safety

Before attempting to ac­cess any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the ma­chine is turned off. Also
ensure that all peripher­al cables, including
phone lines, are discon­nected from the comput­er.

Figure 2 - 1

Hard Disk Location

1

1

2

Hard Disk Drive

The hard disk drive(s) is used to store your data in the computer. The hard disks) can
be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height
of 9.5 mm. The primary hard disk bay is accessible from the bottom of your com­puter as seen below. Note that only Model A/B is pictured, however the procedure
for removing the primary hard disk from Model C/D is identical.

Further details on removing and inserting the hard disk are available in “Upgrading

the Hard Disk Drive(s)” on page 6 - 6.

Model C/D computers feature a primary and secondary hard disk bay (you may
have a second hard disk installed as part of a RAID). See “Removing the Hard Disk

from the Secondary HDD Bay (Model C/D)” on page 6 - 11.

2 - 2 Hard Disk Drive

Storage Devices, Mouse, Audio & Printer



Sound Volume

Adjustment

How high the sound vol­ume can be set depends
on the setting of the vol­ume control within Win-
dows. Click the Volume
icon on the notification
area to check the set­ting.

Peripherals must be
connected before you
turn on the system.

Figure 2 - 2

Optical Device

123

1

2

3

Optical Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the model you purchased (see “Storage” on page D - 4). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 13).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt­ed, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.

2

Optical Device 2 - 3

Storage Devices, Mouse, Audio & Printer



CD Emergency Eject

If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharp­ened pencil or similar
object that may break
and become lodged in
the hole.

Disk Eject Warning

Don’t try to remove a
CD/DVD while the sys­tem is accessing it. This
may cause the system
to “crash”.

2

2 - 4 Optical Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Storage Devices, Mouse, Audio & Printer



DVD Region Note

DVD region detection is
device dependent, not
OS-dependent. You can
select your module’s re­gion code 5 times. The
fifth selection is perma­nent. This cannot be al­tered even if you change
your operating system
or you use the module in
another computer.

Figure 2 - 3

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - West ern Europe, Japan,

South Africa, Middle East & Egypt

• Region 3 - South-East Asia, Taiwan,

South Korea, The Philippines, Indo­nesia, Hong Kong

• Region 4 - South & Central Amer-

ica, Mexico, Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern

Europe, India & Most of Africa

• Region 6 - China

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click Device Manager (Hardware and Sound), then click the + next to
DVD/CD-ROM drives.

3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and
select the DVD Region (tab) to bring up the control p anel to allow you to adjust the
regional code.

2

Optical Device 2 - 5

Storage Devices, Mouse, Audio & Printer



Card Reader Cover

Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust get­ting in to the card read­er.

Figure 2 - 4

Left View

1. Card Reader

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

1

Models A & B

Models C & D

1

2

Multi-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader” on page 4 - 7).

Note: Some of these cards require PC adapters that are usually supplied with the
cards.

2 - 6 Multi-in-1 Card Reader

Storage Devices, Mouse, Audio & Printer



Volume Adjustment

The sound volume level
is set using the volume
control within Windows
(and the volume func­tion keys on the comput­er). Click the volume
icon in the notification
area to check the set­ting.

Headphone

Configuration

It is recommended that
you set the Speaker

Configuration to Ste­reo (not to 5.1 or 7.1

Speaker) when listening
through headphones in
order to maximize audio
quality.

Figure 2 - 5

Realtek Audio

Manager

Right-click the icon
to access the menu
above.

See “HDMI Audio Configuration” on page B - 13 for a description of the audio configura­tion when connecting an HDMI supported display device.
See “THX TruStudio Pro Audio” on page 7 - 110 for more information on the THX TruSt­udio Pro Audio setup.

Audio Features

You can configure the audio options on your computer from the Sound control
panel in Windows, or from the Realtek HD Audio Manager icon in the notifi­cation area/control panel (right-click the notification area icon to bring up an au­dio menu). The volume may also be adjusted by means of the Fn + F5/F6 key
combination (see Table 1 - 4, on page 1 - 11).

2

Audio Features 2 - 7

Storage Devices, Mouse, Audio & Printer

Figure 2 - 6

Realtek Audio

Manager -

Recording Setup

2

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instruc­tions below:

1. Click

2. Click Realtek HD Audio Manager (or right-click the notification area icon and

3. Click Microphone Effects (tab) in Microphone (tab), and then click to select

4. Click OK to close the control panel and save the settings.

Start

, and click

and make sure you are in
select Sound Manager).
Noise Suppression (button), or adjust the Recording Volume level to around 60,

to obtain the optimum recording quality.

Control Panel

Classic View

(or point to

.

Settings

and click

Control Panel

)

2 - 8 Audio Features

Storage Devices, Mouse, Audio & Printer



THX Audio & HDMI

Note that the THX audio ef­fects do not apply to audio
generated through an
HDMI connection (see
page 7 - 113.).

Fn + 5 Audio Toggle

(Model C Only)

The Fn + 5 key combina­tion allows you to toggle the
audio system between ste­reo and surround modes.
The stereo mode will allow
for a louder audio volume.

Note that if you have stereo
mode enabled, and attempt
to demo the speaker configu­ration, then the sound will
only be enabled through the
front and rear speakers (

see

page 2 - 11

).

Figure 2 - 7

Speaker

Configuration (7.1)



Auto Popup Dialog

You should enable the
auto popup dialog to au­tomatically detect when a
device has been
plugged-in. If disabled,
double-click connector
settings and click the
box to enable the auto
popup detection of
plugged-n devices.

Connector Settings

Setup for 5.1 or 7.1 Surround Sound

To setup your system for 5.1 or 7.1 surround sound you will need to connect the au­dio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out
jacks (note: the S/PDIF jack is used for 7.1 surround sound only).

1. Click

2. Click Realtek HD Audio Manager (or right-click the notification area icon and

3. Click Speakers (tab) and click Speaker Configuration (tab).

4. Select 5.1 or 7.1 Speaker from the Speaker Configuration pull-down menu.

Start

and make sure you are in
select Sound Manager).

, and click

Control Panel

Classic View

(or point to

.

Settings

and click

Control Panel

2

)

Audio Features 2 - 9

Storage Devices, Mouse, Audio & Printer

Figure 2 - 8

Connected Device

Auto Popup

Note: Side Speaker Out is required for 7.1 Surround only.

2

5. Plug the front speaker cables into the Headphone-Out Jack.

6. Plug in the other cables (you may require an adapter to connect each cable to the
appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as
follows:

• Line-In Jack = Rear Speaker Out

• Microphone-In Jack = Center/Subwoofer Speaker Out

• S/PDIF-Out Jack = Side Speaker Out (for 7.1 Surround Sound Only)

7. As you plug in each cable a dialog box will pop up (see “Auto Popup Dialog” on

page 2 - 9).

8. Click to put a tick in the appropriate box according to the speaker plugged-in (e.g.
Rear Speaker Out), and then click OK to save the setting.

9. Click OK to exit Realtek HD Audio Manager.

2 - 10 Audio Features

Storage Devices, Mouse, Audio & Printer

Audio Notes for Model C/D Computers (Fn + 5)

Model C/D computers (Model C/D only) feature the Fn +5 key combination to tog­gle between standard audio and enhanced audio. Note the following which applies
to software mode audio configuration through the computer’s internal speak­ers only (this does not apply to surround sound when configured through external

Quadrophonic, 5.1 or 7.1 speaker systems):

• When the Speaker Configuration in Realtek HD Audio Manager is set to
Stereo, you can use the Fn + 5 key combination to help increase the volume
through the speakers.

• When the Speaker Configuration in Realtek HD Audio Manager is set to 5.1/

7.1 Speaker, the best audio configuration will be obtained with the combination
of the Speaker Configuration set to Quadrophonic/5.1/7.1 Speaker, and the
THX TruStudio AP turned ON.

Note that the Fn + 5 key combination is a toggle so you will need to press the key
combination to test if the affect is applied or not.

2

Audio Features 2 - 11

Storage Devices, Mouse, Audio & Printer



Mouse Driver

If you are using an ex­ternal mouse your op­erating system may be
able to auto-configure
your mouse during its
installation or only en­able its basic functions.
Be sure to check the
device’s user docu­mentation for details.

2

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.

2 - 12 TouchPad and Buttons/Mouse

Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 7) you



TouchPad Scrolling

This computer model se­ries may feature different
TouchPad versions.

These TouchPads may
differ in their vertical
scrolling function in most
scrollable windows.

Some TouchPads require
sliding the finger up and
down on the right of the
TouchPad to scroll the
window. Other versions
require tapping/holding
down the finger at the top
right or bottom right of the
TouchPad to scroll the
window.

Figure 2 - 9

Mouse Properties

can configure the functions from the Mouse control panel in Windows, or by d ouble­clicking the TouchPad driver icon in the notification area. You may then config­ure the TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options
to your preferences. You will find further information at www.synaptics.com.

Storage Devices, Mouse, Audio & Printer

2

TouchPad and Buttons/Mouse 2 - 13

Storage Devices, Mouse, Audio & Printer



Show Video

You can get a clearer
view of the gestures in­volved by clicking the
Show Video option for
each gesture item.

Select the gesture (Pinch

Zoom, Rotating, Three
Fingers Down and
Three Finger Flick) in the
Device Settings > Set­tings left tree menu

and click the Show Video
button to see the demon­stration video.

For more details on any of
the gestures see the help
in the lower part of the
right menu window.

Figure 2 - 10

Mouse Properties -

Device Settings

2

Gestures and Device Settings

The Synaptics Gestures Suite application allows you to use a specific gesture (ac­tion) on the surface of the TouchPad to perform specific actions to manipulate doc­uments, objects and applications.

You can configure the settings from the Device Settings tab in Mouse Properties:

1. Click

2. Click Mouse (Hardware and Sound).

3. Click Device Settings (tab) and click Settings.

4. Use the menu tree on the lef t to access the user configurable settings.

Start

, and click

Control Panel

(or point to

Settings

and click

Control Panel

).

2 - 14 TouchPad and Buttons/Mouse

Storage Devices, Mouse, Audio & Printer

Figure 2 - 11

Scrolling Gesture

Figure 2 - 12

Zooming Gesture

Scrolling

The Two-Finger scrolling feature works in most scrollable windows and allows you
to scroll horizontally and vertically. Place two fingers, slightly separated, on the
TouchPad surface and slide both fingers in the direction required (in a straight con­tinuous motion).

Zooming

The Pinch Zoom gesture can be used to perform the same function as a scroll wheel
in Windows applications that support CTRL + scroll wheel zoom functionality.
Place two fingers on the TouchPad (for best results use the tips of the fingers) and
slide them apart to zoom in, or closer together to zoom out.

2

TouchPad and Buttons/Mouse 2 - 15

Storage Devices, Mouse, Audio & Printer

Figure 2 - 13

Rotating Gesture

Figure 2 - 14

Flick/Press

Gesture

2

Rotating

Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments.
Place a finger down on the left “target” zone and keep it stationary. Place another
finger near the middle of the TouchPad and slide it in a circular motion around the
stationary finger (clockwise or counterclockwise) to rotate the object.

Three Finger-Flick/Three Fingers Down (Press)

The Three Finger-Flick gesture may be used to enhance navigation with a variety of
applications such as browsing the Internet or scrolling through a photo viewer. The
Three Fingers Down gesture may be used to launch user-selectable applications.

2 - 16 TouchPad and Buttons/Mouse

Storage Devices, Mouse, Audio & Printer



Parallel Printer

After setting up the print­er attach the parallel ca­ble to the printer.

Connect the printer’s
parallel cable to the Par­allel to USB converter,
and then plug the con­verter into the USB port.

Turn ON the printer,
then turn ON the com­puter.

Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen in­structions.

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.

USB Printer

Most new printers have a USB interface connection. You may use any one of the
ports to connect the printer.

Install Instructions:

1. Set up the printer according to its instructions (unp acking, p aper tr ay, toner/ink car-

tridge etc.).

2. Turn ON the computer.

3. Turn ON the printer.

4. Connect the printer’s USB cable to one of the USB ports on the computer.

5. Windows will identify the printer and either load one of its own drivers or ask you

to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the sidebar
(you will need to purchase a parallel to USB converter).

2

Adding a Printer 2 - 17

Storage Devices, Mouse, Audio & Printer

2

2-18

Chapter 3: Power Management



OS Note

Power management
functions will vary slight­ly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operat­ing system.

(Note: All pictures used
on the following pages
are from the Windows 7
OS.)

Power Management

Overview

To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.

3

Overview 3 - 1

Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

3

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components (see page D - 7).

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button on the top left of the computer for about 2 - 3 se con ds to
turn the computer “on” (note that the power LED on the front of the computer will
turn from orange to green when the computer powers on).

Battery

The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 14).

We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Battery Information” on page 3 - 10.

3 - 2 The Power Sources

Turning On the Computer



Forced Off

If the system “hangs”,
and the Ctrl + Alt + Del
key combination doesn’t
work, press the power
button for 4 seconds, or
longer, to force the sys­tem to turn itself off.

Power Button as

Stand by or

Hibernate Button

You can use the OS’s
Power Options control
panel to set the power
button to send the sys­tem into Stand by or Hi­bernate mode (see your
OS’s documentation, or

“Configuring the Pow­er Buttons” on page 3

- 8 for details).



Shut Down

Note that you should always shut your computer down by choosing the Shut Down com­mand from the bottom right of the Start menu in Windows. This will help prevent hard disk
or system problems.

Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.

Power Management

3

Turning On the Computer 3 - 3

Power Management



Resuming
Operation

See Table 3 - 1, on

page 3 - 9 for informa-

tion on how to resume
from a power-saving
state.

Password

It is recommended that
you enable a password
on system resume in or­der to protect your data.

Figure 3 - 1

Power Plan

Advanced Settings

(Win 7)

Power Plans

The computer can be configured to conserve power by means of power plans. You

3

can use (or modify) an existing power plan, or create a new one.

3 - 4 Power Plans

The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.

Each Windows power plan will also adjust the processor performance of your ma-

Figure 3 - 2

Power Plans (Win 7)

Click to Show/Hide
additional
power plans

chine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view
the High performance plan) for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) pow­ered.

Power Management

3

Power Plans3-5

Power Management

Power-Saving States

You can use power-saving states to stop the computer’s operation and restart where

3

you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the
system sleeps. When you are not using your computer for a certain length of time,
which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left
off (what was on your desktop) without reopening the application(s) and file(s) you
last used.

If your mobile PC in Sleep is running on battery power the system will use only a
minimum amount of power. After an extended period the system will save all the
information to the hard disk and shut the computer down before the battery becomes
depleted.

3 - 6 Power-Saving States

Hibernate

Figure 3 - 3

Start Menu Power

Win 7

Hibernate uses the least amount of power of all the power-saving states and saves

all of your information on a part of the hard disk before it turns the system off. If a
power failure occurs the system can restore your work from the hard disk; if a power
failure occurs when work is saved only to memory, then the work will be lost. Hi-
bernate will also return you to where you last left off within seconds. You should
put your mobile PC into Hibernate if you will not use the computer for a period of
time, and will not have the chance to charge the battery.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t for­get to remove the battery and follow all the safety instructions in Chapter 6), plan
to be away from the computer for several days, or you do not need it to wake up and
run a scheduled task. Returning to full operation from Shut down takes longer than
from Sleep or Hibernate.

Power Management

3

Power-Saving States 3 - 7

Power Management



Password

Protection

It is recommended that
you enable a password
on wake up in order to
protect your data.

However you can dis­able this setting from the
Power Options menu
by clicking Require a

password on wakeup

in the left menu, and se­lecting the options (click

Change settings that
are currently unavail­able).

Figure 3 - 4

Power Options

Define Power

Buttons

3

Configuring the Power Buttons

The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to a power-saving state. Click Choose what the power buttons do on
the left menu in Power Options to bring up the menu.

3 - 8 Configuring the Power Buttons

Resuming Operation



Closing the Lid

If you have chosen to
send the computer to
Sleep when the lid is
closed, raising the lid
will wake the system up.

Table 3 - 1

Resuming
Operation



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down
hot key button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will force the computer to shut down).

You can resume operation from power-saving states by pressing the power button,
or in some cases pressing the sleep button (Fn + F4 key combo).

Power Management

3

Power Status

Power Off Off Press the Power Button

Sleep Blinking Green

Hibernate

Display Turned Off Green Press a Key or Move the Mouse/Touchpad

Icon Color

Off (battery)

Orange (AC/DC adapter)

To Resume

Press the Power Button

Press the Sleep Button (Fn + F4 Key Combo)

Press the Power Button

Configuring the Power Buttons 3 - 9

Power Management



Low Battery

Warning

When the battery is criti­cally low, immediately
connect the AC/DC
adapter to the computer
or save your work, oth­erwise, the unsaved
data will be lost when
the power is depleted.

Figure 3 - 5

Battery Icon

(Notification Area) &

Battery Advanced

Settings

3

Battery Information

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Change plan settings > Change advanced power settings (see Figure

3 - 1 on page 3 - 4).

Click the battery icon in the notification area to see the current battery level and
charge status.

3 - 10 Battery Information

Conserving Battery Power



Windows Mobility

Center

The Windows Mobility
Center control panel

provides an easy point
of access for information
on battery status, power
plans used and wireless
device status etc.

Figure 3 - 6

Windows Mobility

Center

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or communication applications when they are
not being used.

• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.

Power Management

3

Battery Information 3 - 11

Power Management

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life

3

and improve its performance, fully discharge and recharge the battery at least
once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason (e.g. long term storage) see “Removing the Battery”

on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 14 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-

tors” on page 1 - 9 for information on the battery charge status, and to “Battery In­formation” on page 3 - 10 for more information on how to maintain and properly

recharge the battery pack.)

3 - 12 Battery Information

Proper handling of the Battery Pack



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a dam­aged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.



Caution

Danger of explosion if
battery is incorrectly re­placed.

Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s in­structions.

• DO NOT disassemble the battery pack under any circumstances.

• DO NOT expose the battery to fire or high temperatures, it may explode.

• DO NOT connect the metal terminals (+, -) to each other.

Power Management

3

Battery Information 3 - 13

Power Management

Figure 3 - 7

Power Plan Create

3

Battery FAQ

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.

1. Save and close all files and application s.

2. Create a power plan for discharging the battery and set all the options to Never.

3 - 14 Battery Information

3. Click Change plan settings (after creating it) and click Change plan settings >

Figure 3 - 8

Change Plan

Settings / Change

Advanced Power

Settings

Change advanced power settings.

Power Management

3

Battery Information 3 - 15

Power Management

Figure 3 - 9

Power Options

Advanced Settings -

Battery

3

4. Scroll down to Battery and click + to expand the battery options.

5. Choose the options below (click Yes if a warning appears):

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

3 - 16 Battery Information

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.

Power Management

3

Battery Information 3 - 17

Power Management

3

3-18

Chapter 4: Drivers & Utilities

Drivers & Utilities

This chapter deals with installing the drivers and utili­ties essential to the operation or improvement of some
of the computer’s subsystems. The system takes ad­vantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-config­ured with an appropriate driver or utility during oper­ating system installation. Instead, you need to
manually install some system-required drivers and
utilities.

What to Install

The Device Drivers & Utilities + User’s Manual disc
contains the drivers and utilities necessary for the
proper operation of the computer.

Table 4 - 1, on page 4 - 3 lists what you need to install

and it is very important that the drivers are in-
stalled in the order indicated.

Module Driver Installation

The procedures for installing drivers for the PC Cam­era, WLAN, Fingerprint, Combination Bluetooth
& WLAN, 3.75G and Consumer Infrared (for TV

tuner remote) modules (you should also install the

THX Studio Pro Audio and Intel Rapid Storage
Technology drivers as instructed in Chapter 7) are

provided in “Modules” on page 7 - 1.

4

What to Install 4 - 1

Drivers & Utilities

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.

4

Figure 4 - 1 - Drivers Installer Screen 1

1. Check the driver installation order from Table 4 - 1,

on page 4 - 3 (the drivers must be installed in

this order) which is the same as that listed in the

Drivers Installer menu below.

2. Click to select the driver you wish to install, (you
should note down the drivers as you install them).

3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.

4 - 2 Driver Installation

Figure 4 - 2 - Drivers Installer Screen 2

Drivers & Utilities

Windows 7 Driver Page Windows 7 Driver Page

Chipset Page 4 - 6 PC Camera Module Page 7 - 15
Video (VGA) - NVIDIA

Video (VGA) - AMD
LAN Page 4 - 7 Fingerprint Reader Module Page 7 - 42
Card Reader Page 4 - 7 Bluetooth Module Page 7 - 49

TouchPad Page 4 - 7

USB 3.0 Page 4 - 7

Hot Key Page 4 - 7

MEI Driver Page 4 - 8 Intel Rapid Storage Technology Page 7 - 8
Audio Page 4 - 8

Page 4 - 6 Wireless LAN Module Page 7 - 23

3.75G/HSPA Module

(Models A & B Only)

Consumer Infrared Driver (for TV Tuner)

(Models C & D Only)

THX TruStudio Pro Audio

(recommended installation)

Page 7 - 66

Page 7 - 108

Page 7 - 110

Table 4 - 1 - Driver Installation

Note that for Intel and 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN &
Bluetooth drivers.

Driver Installation 4 - 3

4

Drivers & Utilities

Manual Driver Installation

Click the Browse CD/DVD button in the Drivers In­staller application and browse to the executable file in

the appropriate driver folder.

4

Windows Update

After installing all the drivers make sure you enable
Windows Update in order to get all the latest securi ty
updates etc. (all updates will include the latest hotfixes
from Microsoft). See “Windows Update” on page 4 -

9 for instructions.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as
outlined in this chapter.

If the driver is not listed in the Programs and Fea-
tures menu:

1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).

2. Double-click Device Manager (Hardware and
Sound > Device Manager).

3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).

4. Click Driver (tab) and click the Update Driver or

Uninstall button and follow the on screen prompts.

4 - 4 Driver Installation

Drivers & Utilities

User Account Control

If a User Account Control prompt appears as part of
the driver installation procedure, click Continue/Al-
low, and follow the installation procedure as directed.

Windows Security Message

If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or Install to continue the in­stallation procedure.

You will receive this message in cases where the driv­er has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.

New Hardware Found

If you see the message “New Hardware Found” dur­ing the installation procedure (other than when out-
lined in the driver install procedure), click Cancel
to close the window, and follow the installation proce­dure.

4

Driver Installation 4 - 5

Drivers & Utilities



Driver Installation General Guidelines

The driver installation procedure outlined in this Chap­ter (and in Chapter 7 Options & Modules), are accu­rate at the time of going to press.

Drivers are always subject to upgrade and revision so
the exact procedure for certain drivers may differ slight­ly. As a general guide follow the default on screen in­structions for each driver (e.g. Next > Next > Finish)
unless you are an advanced user. In many cases a re­start is required to install the driver.

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or Option Driv-
ers (button) to access the Optional driver menu.

4

Chipset

1. Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer .

4 - 6 Driver Installation

Video (VGA) - NVIDIA

1. Click 2.Install VGA Driver > Yes.

2. Click AGREE AND CONTINUE (button) to
accept the terms of the license agreement.

3. Click Next.

4. Click Close.
OR
Click the RESTART NOW button to restart
the computer.

Video (VGA) - AMD

1. Click 2.Install VGA Driver > Yes.

2. Click Next > Install (button).

3. Click the Express (or Custom if you prefer to
manually configure the driver installation set­tings) button and click Next.

4. Click Accept (button) and click Yes.

5. Click Finish > Yes to restart the computer.

6. After the computer has restarted, click Restart
Now to restart again to refresh the video driver.

(see over)

Drivers & Utilities

After the Video (VGA) driver has been installed, and
the system restarted, the OS will automatically run the
"Winsat.exe" to rate the performance. Allow time for
this process to finish and do not restart during this pro­cess (if you have restarted the system see “Windows

Update” on page 4 - 9).

LAN

1. Click 3.Install LAN Driver > Yes.

2. Click Install.

3. Click Finish to complete the installation.

Card Reader

1. Click 4.Install Cardreader Driver > Yes.

2. Click Install.

3. Click Finish to complete the installation.

TouchPad

1. Click 5.Install Touchpad Driver > Yes.

2. Click Next.

3. Click the button to accept the license, and then
click Next.

4. Click Finish > Restart Now to restart the com­puter.

Hot Key

1. Click 6.Install Hotkey AP > Yes.

2. Click Next > Next.

3. Click Finish > Finish to restart your computer.

USB 3.0

1. Click 7.Install USB 3.0 Driver > Yes.

2. Click Next.

3. Click the button to accept the license and then
click Next.

4. Click Install > Finish.

4

Driver Installation 4 - 7

Drivers & Utilities

MEI Driver

1. Click 8.Install MEI Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish.

4

Audio

1. Click 9. Install Audio Driver > Yes.

2. Click Next.

3. Click Finish to restart the computer.

After installing the audio driver the system will not re­turn to the Drivers Installer screen. To install any of
the optional drivers, eject the Device Drivers & Utili-
ties + User’s Manual disc and then reinsert it (or dou­ble-click the disc icon in My Computer), and click
Option Drivers (button) to access the optional driver
menu.

It is recommended that you install the THX Tru Stu-
dio Pro Audio application (see “THX TruStudio AP

Installation” on page 7 - 110) and Intel Rapid Stor-

age Technology driver (see “IRST Driver Installa-

tion” on page 7 - 8 - required for AHCI & RAID

mode).

(see over)

4 - 8 Driver Installation



Windows Update

After installing all the drivers make sure you enable Windows
Update in order to get all the latest security updates etc. (all up-

dates will include the latest hotfixes from Microsoft).

To enable Windows Update make sure you are connected
to the internet:

1. Click Start, and click Control Panel (or point to Settings
and click Control Panel).

2. Click Windows Update (System and Security/Security).

3. Click Check for updates (button).

4. The computer will now check for updates (you need to be
connected to the internet).

5. Click Install now (button) to begin checking for the
updates.

6. Click Install updates (button) to install the updates.

Drivers & Utilities

Windows Experience Index

After Video (VGA) driver has been installed, and the
system restarted, the OS will automatically run the
"Winsat.exe" to rate the performance. If you have re­started the system during this time then follow the in­structions below to update the information.

After the drivers are installed follow this procedure to
ensure an accurate rating from the Windows Experi-
ence Index (make sure the AC/DC adapter is plugged
in):

1. Click Start, and click Control Panel.

2. Click Performance Information and Tools
(System and Security > System > Check the
Windows Experience Index).

3. Click “Rate this computer/Refresh Now/Re-
run the assessment”.

4. The computer will take a few minutes to assess
the system performance.

5. Close the control panel.

4

Driver Installation 4 - 9

Drivers & Utilities

Models A & B Models C & D

Optional Drivers

See the pages indicated for the driver installation procedures for any modules included in your purchase option.

4

Figure 4 - 3 - Optional Drivers Installer Screen

Note that for Intel and 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN &
Bluetooth drivers.

4 - 10 Driver Installation

Drivers & Utilities

PC Camera

See the install procedure in “PC Camera Module” on

page 7 - 14.

Wireless LAN

See the appropriate install procedure for your WLAN
module in “Wireless LAN Module” on page 7 - 22.

Fingerprint Reader Module

See the install procedure in “Fingerprint Reader

Module” on page 7 - 42.

Bluetooth & WLAN Combo Module

See “3rd Party Bluetooth Combo Driver Installa-

tion” on page 7 - 49 or “Intel Bluetooth Combo Driv­er Installation” on page 7 - 57.

3.75G/HSPA Module (Models A & B Only)

See the introduction in “3.75G/HSPA Module” on

page 7 - 62, and check the installation procedure.

Consumer Infrared (for TV Tuner Remote ­Models C & D Only)

See the install procedure in “TV Tuner Module” on

page 7 - 107.

THX TruStudio AP

See the install procedure in “THX TruStudio Pro Au-

dio” on page 7 - 110.

Intel Rapid Storage Technology Driver

See the install procedure in “Intel Rapid Storage

Technology” on page 7 - 8.

4

Driver Installation 4 - 11

Drivers & Utilities

4

4-12

Chapter 5: BIOS Utilities



BIOS Screens

Note that the BIOS
screens pictured on
these pages are intend­ed for guidance in set­ting up your system’s
BIOS.

BIOS versions are sub­ject to constant change
and revision, therefore
your computer’s actual
screens may appear
slightly different from
those pictured on these
pages.

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Setup utility

If your computer has never been set up, or you are making impo rtant changes to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your
system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.

BIOS Utilities

5

Overview 5 - 1

BIOS Utilities

The Power-On Self Test (POST)

If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you
turn on the computer the system takes a few seconds to conduct a POST, including
a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary

5

and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load

the operating system. Once that starts, you can’t get into Setup without rebooting.

5 - 2 The Power-On Self Test (POST)

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and “non­fatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) and you can then press F7 (the F7 on screen
will be highlighted to illustate that the system is processing the request) for boot op­tions.

Press F2 (give the system a few seconds to enter Setup; the F2 on screen will be
highlighted to illustate that the system is processing the request) to run the Setup
program and try to correct the problem. If you still get an error message after you
change the setting, or if the “cure” seems even worse, call for help.

BIOS Utilities

5

The Power-On Self Test (POST) 5 - 3

BIOS Utilities



BIOS Settings

Warning

Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-

up and restore the Pre­vious Values with

<F2>, or Optimized De­faults with <F3>.

The Setup Utility

The Aptio Setup Utility tells the syst em how to configure itself and manage basic
features and subsystems (e.g. port configuration).

Entering Setup

To enter Setup, turn on the computer and press F2 (give the system a few seconds

5

to enter Setup; the F2 on screen will be highlighted to illustate that the system is pro-
cessing the request) during the POST (or press F7 for boot options). If you get a
“Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.

If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.

5 - 4 The Setup Utility

To see the boot options press F7.