Clevo N150SC, N150SD, N155SC, N155SD User guide

V15.1.00

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©January 2015

Trademarks

Intel and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

ErP Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode:

• Off Mode < 0.5W

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc ed radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interfer ence that may cause undesired operation of the

device.

Preface



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit:

• Full Range AC/DC Adapter – AC in 100 - 240V, 50 - 60Hz DC Output 19.5V, 6.15A (120 Watts) minimum

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive

heat or direct sunlight.

Do not leave it in a place where

foreign matter or moisture may

affect the system.

Don’t use or store the computer

in a humid environment.

Do not place the computer on

any surface that will block the

Vents/Fan Intakes.

VII

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

5. Take care when using peripheral devices.

Use only approved brands of peripherals.

VIII

Do not disassemble the computer by yourself.

Unplug the power cord befor e attaching peripheral devices.

Perform routine maintenance on your computer.

Servicing



Bottom Cover Removal Warning

Users should not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty. If you need to replace/remove the hard disk/RAM/optical device etc., for any reason, please contact your distributor/supplier for further information.

Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

Preface



Power Safety Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).

You must also remove your battery in order to prevent accidentally turning the machine on.

Before removing the battery disconnect the AC/DC adapter from the computer.

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the powe r co rd, be sure to di sconn ect it b y the plug head , no t by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mechanism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient temperature environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

Preface



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

General Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu alified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

XII

Cleaning



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply and then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

Preface

XIII

Preface



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.

Travel Considerations

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both

hardware and software. Make sure your “papers” are handy.

XIV

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in fron t of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

• Y our knees sho uld be sligh tly higher th an your hips. Place yo ur feet flat on the floor or on a footrest if necessary.

• Use a chair with a back and adjust it to support your lower back comfortably.

• Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

• Alter your posture frequently.

• Stretch and exercise your body several times a day.

• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.

XVI

Preface

Lighting

Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

LCD Electro-Plated Logos

Note that in computers featuring a raised LCD electro-plated logo, the logo is covered by a protective adhesive. Due to general wear and tear, this adhesive may deteriorate over time and the exposed logo may develop sharp edges. Be careful when handling the computer in this case, and avoid touching the raised LCD electro-plated logo. Avoid placing any other items in the carrying bag which may rub against the top of the computer during transport. If any such wear and tear develops contact your distributor/supplier.

XVII

Preface

XVIII

Preface

Contents

Notice .............................................................................................................................................................I

ErP Off Mode Power Consumption Statement: ...........................................................................................II

FCC Statement ............................................................................................................................................IV

FCC RF Radiation Exposure Statement: .....................................................................................................V

Instructions for Care and Operation ......................................................................................................... VII

Servicing .....................................................................................................................................................IX

Power Safety ................................................................................................................................................X

Polymer Battery Precautions ......................................................................................................................XI

General Battery Precautions ..................................................................................................................... XII

Cleaning ...................................................................................................................................................XIII

Servicing ..................................................................................................................................................XIII

Travel Considerations ..............................................................................................................................XIV

Quick Start Guide

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Software ........................................................................................................................................1-4

System Startup ...........................................................................................................................................1-5

XIX

Preface

Model Differences .....................................................................................................................................1-6

LCD Panel Open - Model A ......................................................................................................................1-7

LCD Panel Open - Model B ......................................................................................................................1-8

LCD Panel Open - Model C ......................................................................................................................1-9

LED Indicators .........................................................................................................................................1-10

Illuminated LED Keyboard .....................................................................................................................1-11

Control Center .........................................................................................................................................1-12

Flexikey® Application ............................................................................................................................1-13

Flexikey® Application Features: .............................................................................................................1-14

Keyboard Shortcuts .................................................................................................................................1-15

Function Keys & Visual Indicators .........................................................................................................1-16

Front & Rear Views .................................................................................................................................1-17

Right View ...............................................................................................................................................1-18

Left View .................................................................................................................................................1-20

Bottom View - Model A ..........................................................................................................................1-22

Bottom View - Model B ..........................................................................................................................1-23

Bottom View - Model C ..........................................................................................................................1-24

Windows 8.1 Control Panel .....................................................................................................................1-25

Windows 8.1 Start Screen & Desktop .....................................................................................................1-28

Apps & Tiles ............................................................................................................................................1-29

Desktop Application ................................................................................................................................1-30

The Charms Bar .......................................................................................................................................1-31

Preface

Windows 8.1 Taskbar ..............................................................................................................................1-33

Video Features .........................................................................................................................................1-34

Microsoft Hybrid Graphics ......................................................................................................................1-34

Power Options .........................................................................................................................................1-38

Running Apps ..........................................................................................................................................1-39

Storage Devices, Mouse, & Audio

Overview ....................................................................................................................................................2-1

Hard Disk Drive/Solid State Drive ............................................................................................................2-2

Optical (CD/DVD) Device ........................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-in-1 Card Reader ..............................................................................................................................2-6

Audio Features ...........................................................................................................................................2-7

Setup for Audio Recording ........................................................................................................................2-8

Touchpad and Buttons/Mouse ...................................................................................................................2-9

Touchpad Sensitivity ...............................................................................................................................2-10

One-Finger ...............................................................................................................................................2-14

Multi-Finger .............................................................................................................................................2-17

Additional ................................................................................................................................................2-19

XXI

Preface

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

Battery ........................................................................................................................................................3-2

Turning On the Computer ..........................................................................................................................3-3

Shutting the Computer Down ....................................................................................................................3-4

Power Plans ...............................................................................................................................................3-5

Power-Saving States ..................................................................................................................................3-7

Sleep ..........................................................................................................................................................3-7

Hibernate ....................................................................................................................................................3-8

Shut down ..................................................................................................................................................3-8

Configuring the Power Buttons .................................................................................................................3-9

Resuming Operation ................................................................................................................................3-11

Power Conservation Modes .....................................................................................................................3-12

Battery Information .................................................................................................................................3-14

Battery Power ..........................................................................................................................................3-14

Conserving Battery Power .......................................................................................................................3-15

Battery Life ..............................................................................................................................................3-16

New Battery .............................................................................................................................................3-16

Recharging the Battery with the AC/DC Adapter ...................................................................................3-16

Proper handling of the Battery Pack ........................................................................................................3-17

XXII

Preface

Battery FAQ .............................................................................................................................................3-18

Drivers & Utilities

What to Install ............................................................................................................................................4-1

Module Driver Installation ........................................................................................................................4-1

Driver Installation ......................................................................................................................................4-2

Updating/Reinstalling Individual Drivers ..................................................................................................4-5

User Account Control ................................................................................................................................4-6

Windows Security Message .......................................................................................................................4-6

New Hardware Found ................................................................................................................................4-6

Driver Installation Procedure .....................................................................................................................4-7

Chipset .......................................................................................................................................................4-7

Video (VGA) .............................................................................................................................................4-7

NVIDIA Video (VGA) ..............................................................................................................................4-7

LAN ...........................................................................................................................................................4-7

Card Reader ...............................................................................................................................................4-7

Touchpad ...................................................................................................................................................4-8

Airplane .....................................................................................................................................................4-8

Hot Key ......................................................................................................................................................4-8

MEI Driver .................................................................................................................................................4-8

Audio .........................................................................................................................................................4-8

Optional Drivers ......................................................................................................................................4-10

XXIII

Preface

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Power-On Self Test (POST) ...............................................................................................................5-2

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

The Setup Utility ........................................................................................................................................5-4

Entering Setup ...........................................................................................................................................5-4

Setup Screens .............................................................................................................................................5-5

Main Menu .................................................................................................................................................5-6

System Time & Date (Main Menu) ...........................................................................................................5-6

SATA Port # (Main Menu) ........................................................................................................................5-7

OffBoard SATA Controller Configuration (Main Menu) .........................................................................5-7

ME FW Version/System/Extended Memory (Main Menu) ......................................................................5-7

MB Series/BIOS Revision/KBC/EC firmware Revision/Mac Address (Main Menu) ..............................5-7

Advanced Menu .........................................................................................................................................5-8

Intel(R) Rapid Start Technology (Advanced Menu) .................................................................................5-8

SATA Mode (Advanced Menu) ................................................................................................................5-9

Boot Logo (Advanced Menu) ....................................................................................................................5-9

Power On Boot Beep (Advanced Menu) ...................................................................................................5-9

Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-9

Security Menu ..........................................................................................................................................5-10

XXIV

Preface

Set Supervisor Password (Security Menu) ..............................................................................................5-10

Set User Password (Security Menu) ........................................................................................................5-11

Password on boot: (Security Menu) ........................................................................................................5-11

Secure Boot Control (Security Menu) .....................................................................................................5-12

TPM Configuration (Security Menu) ......................................................................................................5-13

Boot Menu ...............................................................................................................................................5-14

Boot Option Priorities (Boot Menu) ........................................................................................................5-15

UEFI Boot (Boot Menu) ..........................................................................................................................5-15

Exit Menu ................................................................................................................................................5-16

Modules

Overview ....................................................................................................................................................6-1

PC Camera Module ....................................................................................................................................6-2

PC Camera Audio Setup ............................................................................................................................6-3

Camera App ...............................................................................................................................................6-4

Camera Options .........................................................................................................................................6-5

Taking Pictures/Capturing Video ..............................................................................................................6-6

Camera Roll ...............................................................................................................................................6-7

Wireless LAN Module .............................................................................................................................6-11

3rd Party 802.11b/g/n Driver Installation ................................................................................................6-12

Intel® WLAN Driver Installation ............................................................................................................6-12

Qualcomm Atheros WLAN Combo Driver Installation ..........................................................................6-13

XXV

Preface

WLAN Configuration in Windows .........................................................................................................6-14

Fingerprint Reader Module ......................................................................................................................6-17

Fingerprint Reader Driver Installation .....................................................................................................6-18

Fingerprint Module Configuration ..........................................................................................................6-19

Bluetooth & WLAN Combo Module ......................................................................................................6-21

3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................6-22

Intel Bluetooth Combo Driver Installation ..............................................................................................6-22

Qualcomm Atheros Bluetooth Combo Driver Installation ......................................................................6-23

Bluetooth Configuration in Windows ......................................................................................................6-24

Intel® Rapid Storage Technology ...........................................................................................................6-27

IRST Driver Installation ..........................................................................................................................6-27

Intel® Rapid Start Technology Driver ....................................................................................................6-28

Intel® Rapid Start Technology Configuration ........................................................................................6-29

Intel® Rapid Start Technology Driver Installation .................................................................................6-35

Sound Blaster Cinema 2 ..........................................................................................................................6-36

Sound Blaster Cinema 2 Installation .......................................................................................................6-36

Sound Blaster Cinema 2 Application ......................................................................................................6-37

Sound Blaster Cinema 2 SBX Pro Studio ................................................................................................6-41

Trusted Platform Module .........................................................................................................................6-46

Enabling & Managing TPM ....................................................................................................................6-47

TPM Management in Windows ...............................................................................................................6-48

TPM Actions ............................................................................................................................................6-50

XXVI

Preface

3G/4G Module .........................................................................................................................................6-52

3G/4G Configuration in Windows ...........................................................................................................6-54

Wireless Display ......................................................................................................................................6-57

Wireless Display Configuration ..............................................................................................................6-58

Troubleshooting

Overview ....................................................................................................................................................7-1

Basic Hints and Tips ..................................................................................................................................7-2

Backup and General Maintenance .............................................................................................................7-3

Viruses .......................................................................................................................................................7-4

Upgrading and Adding New Hardware/Software ......................................................................................7-5

Problems and Possible Solutions ...............................................................................................................7-7

3G/4G Module PIN Code & Power-Saving ............................................................................................7-14

Resolving the “Insert a SIM” issue with the 3G/4G Module (Windows 8.1) .........................................7-16

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Ports and Jacks ..........................................................................................................................................A-2

Card Reader ..............................................................................................................................................A-2

DC-In Jack ................................................................................................................................................A-2

External Monitor (VGA) Port ...................................................................................................................A-2

Mini DisplayPort 1.2 ................................................................................................................................A-2

HDMI-Out Port .........................................................................................................................................A-3

XXVII

Preface

Headphone-Out Jack .................................................................................................................................A-3

Microphone-In Jack ..................................................................................................................................A-3

RJ-45 LAN Jack .......................................................................................................................................A-3

S/PDIF-Out Jack .......................................................................................................................................A-3

Security Lock Slot ....................................................................................................................................A-3

USB 3.0 Port .............................................................................................................................................A-4

Control Center & Flexikey®

Overview ...................................................................................................................................................B-1

Control Center ..........................................................................................................................................B-1

Flexikey® .................................................................................................................................................B-1

Power Modes ............................................................................................................................................B-3

Control Center Menus ...............................................................................................................................B-4

Power Status (System Program) .............................................................................................................B-5

Brightness (System Program) ..................................................................................................................B-5

Volume (System Program) .......................................................................................................................B-5

Fan Speed (System Program) ...................................................................................................................B-5

Power Conservation (System Program) ....................................................................................................B-6

Sleep Button (System Program) ..............................................................................................................B-6

Display Switch (System Program) ...........................................................................................................B-6

Time Zone (System Program) .................................................................................................................B-6

Desktop Background (System Program) .................................................................................................B-6

XXVIII

Preface

Backlight Keyboard (Device) ...................................................................................................................B-7

TouchPad/PC Camera (Device) ...............................................................................................................B-7

Left Windows Key (Gaming) ..................................................................................................................B-7

Headphone (Gaming) ...............................................................................................................................B-7

Flexikey® (Gaming) .................................................................................................................................B-7

Caps Lock/Scroll Lock/ Number Lock/Airplane Mode ...........................................................................B-7

Flexikey® Application .............................................................................................................................B-8

Language Interface ...................................................................................................................................B-9

Keyboard Settings - Express Key ...........................................................................................................B-13

Enabling Time Record ............................................................................................................................B-15

Keyboard Settings - Launch App ...........................................................................................................B-17

Keyboard Settings - Express Text ..........................................................................................................B-19

Keyboard Settings - Disable ...................................................................................................................B-21

Mouse Settings - Express Key ................................................................................................................B-22

Enabling Time Record for Mouse Settings ............................................................................................B-23

Mouse Settings - Launch App ................................................................................................................B-24

Mouse Settings - Express Text ...............................................................................................................B-26

Mouse Settings - Disable ........................................................................................................................B-28

Statistics ..................................................................................................................................................B-29

NVIDIA Video Driver Controls

Video Driver Installation ..........................................................................................................................C-1

XXIX

Preface

Video (VGA) ............................................................................................................................................C-1

NVIDIA Video (VGA) .............................................................................................................................C-1

Microsoft Hybrid Graphics .......................................................................................................................C-2

Intel® Dynamic Video Memory Technology ...........................................................................................C-4

Intel® HD Graphics Control Panel ...........................................................................................................C-5

Display Devices & Options ....................................................................................................................C-19

Attaching Other Displays .......................................................................................................................C-20

Attaching Other Displays - Devices (Charms Bar) ................................................................................C-23

Configuring an External Display In Windows .......................................................................................C-24

NVIDIA Control Panel ...........................................................................................................................C-26

Customization Options ...........................................................................................................................C-28

Set PhysX® Configuration .....................................................................................................................C-32

NVIDIA GeForce Experience ................................................................................................................C-33

NVIDIA GeForce Experience - BatteryBoost ........................................................................................C-35

NVIDIA GeForce Experience - ShadowPlay .........................................................................................C-36

HDMI Audio Configuration ...................................................................................................................C-37

Specifications

Processor ...................................................................................................................................................D-2

Core Logic ................................................................................................................................................D-2

Display ......................................................................................................................................................D-2

Memory .....................................................................................................................................................D-2

XXX

Preface

Video Adapter Options .............................................................................................................................D-2

Storage ......................................................................................................................................................D-3

BIOS .........................................................................................................................................................D-3

Audio ........................................................................................................................................................D-3

Keyboard & Pointing Device ....................................................................................................................D-3

Indicators ..................................................................................................................................................D-3

Interface ....................................................................................................................................................D-3

Card Reader ..............................................................................................................................................D-3

Slots ..........................................................................................................................................................D-3

Communication .........................................................................................................................................D-4

Operating System ......................................................................................................................................D-4

Features .....................................................................................................................................................D-4

Security .....................................................................................................................................................D-4

Power Management ..................................................................................................................................D-4

Power ........................................................................................................................................................D-4

Environmental Spec ..................................................................................................................................D-4

Physical Dimensions & Weight ................................................................................................................D-4

XXXI

Preface

XXXII

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk and card reader), TouchPad & Mouse and Audio Features.

• Chapter 3 The computer’s power management options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 A quick guide to the computer’s PC Camera, Wireless LAN, Fingerprint, Bluetooth & WLAN Combo, Sound Blaster Audio and Intel modules (some of which may be optional depending on your purchase configuration).

• Chapter 7 A troubleshooting guide.

• Appendix A Definiti ons of the interface, ports/jacks which allow your computer to c ommun icat e with ex te rnal devices.

• Appendix B Information on the Control Center . and Combo Keys Application.

• Appendix C Information on the Video driver controls.

• Appendix D The computer’s specification.

Overview 1 - 1



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1 and “BIOS Utilities” on page 5 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4

- 4. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your

system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers

& Utilities” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Not Included

Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.

Overview 1 - 3



Windows OS

Note that the information included on the following pages is for Windows 8.1 only. In order to run Windows 8.1 (64 bit) your computer requires a minimum 2GB of system memory (RAM).

Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 o perating system is supported.

1 - 4 Overview

Quick Start Guide

135°



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command in Windows (see page 1 - 38). This will help prevent hard disk or system problems.

System Startup

1. Remove all packing materials, and place the computer on a stable surface, and securely attach any peripherals you want to

use with the notebook (e.g. keyboard and mouse) to their ports.

2. When first setting up the computer use the following proced ure (as to safeguard the computer during shipping, the

battery will be locked to not power the system until first connected to the AC/DC adapter and initially set up as below):

• Attach the AC/DC adapter cord to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and

connect the AC power cord to the AC/DC adapter and leave it there for 6 seconds or longer.

• Remove the adapter cord from the computer’s DC-In jack, and then plug it back in again; the battery will now be unlocked.

3. Use one hand to raise the

hand to support the base of the computer (Note: Never lift the computer by the lid/LCD).

4. Press the power button on the top of the computer for about 2 - 3 seconds to turn the computer “on” (note that the power

LED on the front of the computer will turn from orange to green when the computer powers on).

lid/LCD to a comfortable viewing angle (it is preferable not to exceed 135 degrees);

use the other

Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In/Opening the Lid/LCD

System Startup 1 - 5

Quick Start Guide

Model Differences

This notebook series includes three different model types (with two specification types for Models A & B - see Ap-

pendix D for full specification details) that mainly differ as indicated in the table below. Note that your model may

appear slightly different from those pictured in this manual.

Model A Model B

Feature

Specification I Specification II Specification I Specification II

Model C

Design Style

Display

Video

Controller

Card Slots

3G/4G Module

nVIDIA® GeForce

GTX 950M

1 - 6 System Startup

See Page 1 - 7 See Page 1 - 8 See Page 1 - 9

17.3" (43.94cm) FHD

15.6" (39.62cm) FHD (1920 * 1080), 3.2 - 3.5 mm, 16:9 Backlit Panel

nVIDIA® GeForce

GTX 960M

Three M.2 Slots Two M.2 Slots

Supported Not Supported

nVIDIA® GeForce

GTX 950M

nVIDIA® GeForce

GTX 960M

(1920 * 1080), 6.0mm,

16:9 Backlit Panel

nVIDIA® GeForce

GTX 960M

Table 1 - 1 - Model Differences

LCD Panel Open - Model A

Figure 1 - 2

LCD Panel Open

Model A

1. Built-In PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Speakers

6. Power Button

7. Illuminated (White) LED Keyboard

8. TouchPad & Buttons

9. Fingerprint Reader Sensor (Optional)

Note that the Touchpad/ Clickpad and Buttons has a valid operational area indicated within the dotted lines above.



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices (e.g. WLAN, Bluetooth or 3G/ 4G) aboard aircraft is usually prohibited. Make sure any wireless modules are OFF (i.e. the system is in Airplane Mode) if you are using the computer aboard aircraft.

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/Off, and check the LED indicator for the power status.

Quick Start Guide

LCD Panel Open - Model A 1 - 7

Figure 1 - 3

LCD Panel Open

Model B

1. Built-In PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Speakers

6. Power Button

7. LED Indicators

8. Illuminated (White) LED Keyboard

9. TouchPad & Buttons

10.Fingerprint Reader Sensor (Optional)

Note that the Touchpad/ Clickpad and Buttons has a valid operational area indicated within the dotted lines above.



Wireless Device

Operation Aboard

Aircraft

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/Off, and check the LED indicator for the power status.

Quick Start Guide

LCD Panel Open - Model B

1 - 8 LCD Panel Open - Model B

LCD Panel Open - Model C

Figure 1 - 4

LCD Panel Open

Model C

1. Built-In PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Speakers

6. Power Button

7. Illuminated (White) LED Keyboard

8. TouchPad & Buttons

9. Fingerprint Reader

Note that the Touchpad/ Clickpad & Buttons has a valid operational area indicated within the dotted lines above.



Wireless Device

Operation Aboard

Aircraft

Use Fn + F11 Airplane Mode key combination to toggle Airplane Mode On/Off, and check the LED indicator for the power status.

Quick Start Guide

LCD Panel Open - Model C 1 - 9

Quick Start Guide

LED Indicators

The LED indicators at the front of the computer display helpful information about the current status of the system.

Icon Color Description Icon Color Description

White

White HDD Activity Blinking Orange

White

Airplane Mode is ON (the WLAN, Bluetooth

& 3G/4G Modules are OFF)

Number Lock is Activated

Caps Lock is Activa ted

Scroll Lock is Activated

1 - 10 LCD Panel Open - Model C

Orange The Battery is Charging

The Battery has Reached Critically Low

Power Status

White The Battery is Fully Charged

Orange AC/DC Power is Plugged In

White The Computer is On

Blinking White The Computer is in Sleep Mode

Table 1 - 2 - LED Indicators

Illuminated LED Keyboard



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot-keys unique to the system’s regular keyboard may not work.

Scr Lk

Hold down the Fn Key and Scr Lk to enable scroll lock/number lock, and check the LED indicator for status.

Numerical

Play/Pause Key

Function Keys

Scr Lk Key

Fn Key

Game Control Keys

Num Lk Key

Windows Logo Key

Menu/Application Key

Numerical Keypad



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

The white illuminated keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 4, on page 1 - 16 for full function key combination details.

Figure 1 - 5 - Illuminated (White) LED Keyboard

Quick Start Guide

Illuminated LED Keyboard 1 - 11



Control Center Access

To run the Control Center press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar.

Close the Control Center by clicking the close icon in the top right of the panel (move the cursor onto the top right corner of the panel to highlight it).

Quick Start Guide

Control Center

When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch

Pad on/off (see Appendix B for full details).

1 - 12 Control Center

in the notification area of the taskbar to toggle the Control Center on/off. The Con-

Figure 1 - 6 - Control Center

Quick Start Guide

Flexikey® Enabled

Flexikey® Disabled

Flexikey® Application

The Flexikey® application is a quick hotkey configuration application, which allows you to assign a single key to launch multiple key combinations, or to launch programs and applications, to create text macros and to disable certain keys. The application can also be used to configure the mouse buttons to create hotkeys for gaming etc. All the configuration settings are retained under (up to12) profiles to which the settings are applied. Click Flexikey® in the Gaming section of the Control Center, or the click the icon in the notification area of the taskbar, to launch the application (see Appendix B for full details).

Figure 1 - 7 - Flexikey® Hotkey Application

Flexikey® Application 1 - 13

Quick Start Guide

Flexikey® Application Features:

For full details see “Flexikey® Application” on page B - 8.

• EXPRESS KEY - This feature allows you to configure a single key (or mouse click) to send multiple key

combinations, or to create more useful shortcut keys This is useful in gaming or when using applications which have a complex set of keyboard shortcuts.

• LAUNCH APP - This simply assigns single keys (or mouse clicks) to launch any program’s or application’s

executable file.

• EXPRESS TEXT - With this you can assign single keys (or mouse clicks) to send commonly used strings

of text.

• DISABLE - Use this function to disable any keyboard keys or mouse buttons.

• STATISTICS - Use this to quickly record keys in use in any application, and to disable unused keys.

1 - 14 Flexikey® Application

Keyboard Shortcuts



Windows Logo

Keyboard Shortcut

Use the Windows logo key + D key com- bination to switch between the Start screen and Windows Desktop.

Menu/Application

Keyboard Shortcut

When the Desktop app is running you can use the Menu/Application key on the keyboard to display the context menu as per a mouse right-click. In the Start screen this function is useful to quickly display the All Apps icon.

The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navigation/operation in

Windows Logo

Key +

Tap Winkey

CDisplay Charms menu D Switch to the Windows Desktop and toggle show Desktop

F Display file Search

I Open the Settings charm

K Open the Connect charm

L Lock the computer and display the Lock screen P Display the Second Screen menu (see Figure 1 - 23 on page 1 - 34) R Switch to the Windows Desktop and display the Run dialog box Z Access the Customize Bar (see Figure 1 - 18 on page 1 - 29)

Windows 8.1

Description

Toggle between the Start screen and the foremost running app or the

Windows Desktop

Switch to the Windows desktop and launch Windows Explorer with

Computer displayed

Table 1 - 3 - Keyboard Shortcuts

Quick Start Guide

Flexikey® Application 1 - 15

Quick Start Guide

Function Keys & Visual Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down.

Keys Function/Visual Indicators Keys Function/Visual Indicators

Fn +

Fan Control Toggle

Automatic / Full

Power

Play/Pause (in Audio/Video Programs)

Touchpad Toggle

(Press a key to or use Touchpad to turn on)

Backlight Keyboard

Toggle Off/High/Low

Turn LCD Backlight Off

Volume Decrease/Increase Fn + Backspace Flexikey® Enable/Disable

Table 1 - 4 - Function Keys & Visual Indicators

1 - 16 Flexikey® Application

Mute Toggle

Fn +

Control Center Toggle (see over)

Display Toggle

Brightness Decrease/Increase

PC Camera

Power T oggle

Airplane

Mode Toggle

Sleep Toggle

Front & Rear Views

Figure 1 - 8

Front & Rear Views

1. LED Power Indicators

2. Vent/Fan Intake

3. 1 * USB 3.0 Port

4. HDMI-Out Port

5. Mini Display Port 1.2

6. DC-In Jack



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.

3 4



HDMI Port / Mini Display Ports

Note that the HDMI Port and Mini Display Port support video and audio signals to attached external displays.

Note that Sound Blaster Cinema 2 audio will be disable d when you are connecting to an external display through an HDMI or Mini Display Port connection.

5 6

3 4 5 6

Model C

3 425 6

Model A

Models A & B

Model B

Quick Start Guide

Front & Rear Views 1 - 17

Figure 1 - 9

Right View

1. SIM Card Reader

(for 3G/4G USIM Cards - Models A & B Only - see over)

2. Multi-In-1 Card

Reader

3. 1 * USB 3.0 Port

4. External Monitor

Port

5. RJ-45 LAN Jack



USB Ports

Note that the connections to the USB ports only fit one way, do not force them.

Model A

Model C



Multi-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

Model B

Quick Start Guide

Right View

1 - 18 Right View

3G/4G Module USIM Card Installation



USIM Card

Orientation

Note that the USIM card’s readable side (with the gold-colored contacts) should face downwards as illustrated.

Figure 1 - 10

USIM Card Insertion



USIM Card Ejection

Simply press on the USIM card to eject it, however do not do this while a connection is in progress. If you do eject the card while a 3G/4G connection is ongoing, you will need to shut down the system, reinsert the USIM card, restart the system and then reestablish the 3G/4G connection.

If you wish to change USIM cards then you will need to shut the system down, reinsert the USIM card, restart the system and then reestablish the 3G/4G connection.

Model A

Note that only Model A is pictured, however the card insertion procedure for Model B is identical. Model C computers do not support a 3G/4G module.

(For Model A & B Computers Only) Insert the USIM card as illustrated below (pay careful attention to the orientation of the card as the gold contact side of the card should face downwards) until it clicks fully into position. To eject the card simply press it until it ejects, but do not attempt to eject the card while connected to a 3G/4G network (see below).

Quick Start Guide

Right View 1 - 19

Figure 1 - 11

Left View

1. Security Lock Slot

2. 2 * USB 3.0 Ports

3. S/PDIF-Out Jack

4. Microphone Jack

5. Headphone Jack

6. Optical Device Drive Bay (for DVD Device)

2 43 5

Model A

Model C

Model A

Model B

2 43 5

Quick Start Guide

Left View

1 - 20 Left View



Disk Eject Warning

Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop the disk first then eject it, or press the stop button twice.

CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole. Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”.



Changing DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code (see “DVD

Regional Codes” on page 2 - 5).

DVD region detection is device dependent, not OSdependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Quick Start Guide

Left View 1 - 21

Figure 1 - 12

Bottom View

Model A

1. Fan Outlet/Intake

2. Battery



Battery Removal

Note that the built-in battery is not user removable. Removing the

battery will violate the terms of your warranty.

If you need to remove the battery for any reason, please contact your distributor/supplier for further information.



Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 14 for full instructions.



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.

Bottom Cover Removal

Warning

Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.

If you need to replace/remove the hard disk/ RAM/optical device etc., for any reason, please contact your distributor/ supplier for further information.

Quick Start Guide

Bottom View - Model A

1 - 22 Bottom View - Model A

Bottom View - Model B

Figure 1 - 13

Bottom View

Model B

1. Fan Outlet/Intake

2. Battery



Battery Removal

Note that the built-in battery is not user removable. Removing the

battery will violate the terms of your warranty.

If you need to remove the battery for any reason, please contact your distributor/supplier for further information.



Battery Information



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.

Bottom Cover Removal

Warning

Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.

If you need to replace/remove the hard disk/ RAM/optical device etc., for any reason, please contact your distributor/ supplier for further information.

Quick Start Guide

Bottom View - Model B 1 - 23

Figure 1 - 14

Bottom View

Model C

1. Fan Outlet/Intake

2. Battery

3. HDD Bay



Battery Removal

Note that the built-in battery is not user removable. Removing the

battery will violate the terms of your warranty.

If you need to remove the battery for any reason, please contact your distributor/supplier for further information.



Battery Information



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.

Bottom Cover Removal

Warning

Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.

If you need to replace/remove the hard disk/ RAM/optical device etc., for any reason, please contact your distributor/ supplier for further information.

2 3

Quick Start Guide

Bottom View - Model C

1 - 24 Bottom View - Model C

Windows 8.1 Control Panel



Windows Versions

Note that the information included on the following pages is for the latest updated version of Windows 8.1 only.

Make sure you enable Windows Update in order to get all the latest security updates etc. (see “Windows Up-

date” on page 4 - 9).

Move the mouse to the bottom left

Start Screen

Desktop app

of the screen and right-click to access the menu.

Throughout this manual you will see an instruction to open the Control Panel. R

ight-click the lower left hot corner to bring up the context menu (or use the Win-

dows Logo Key + X key combination)

Desktop app or Start screen.

and select Control Panel in both the

Quick Start Guide

Figure 1 - 15 - Windows Context Menu

Windows 8.1 Control Panel 1 - 25



Keyboard Shortcut to Control Panel

You can also use keyboard shortcuts to access the Contro l Pa nel. Press th e Win dows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.

Quick Start Guide

The Control Panel can be accessed in a number of ways in Windows 8.1.

•Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type

Control Panel and select it from the results to the left.

• Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the top menu and select Open Control Panel from the ribbon.

• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu.

• Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System).

• Right-click the Start button to bring up the menu and select Control Panel (see Figure 1 - 16 on page 1

- 27).

1 - 26 Windows 8.1 Control Panel

Right-click the Start button in the Desktop app (or use the Windows Logo Key



Display Most

Recently Used

Apps

If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app.

To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list.

Move the mouse to the bottom left of the screen and right-click the Start button to access the menu.

+ X key combination) to bring up an advanced context menu of useful features

such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.

Figure 1 - 16 - Advanced Context Menu (Right-Click Start Button)

Quick Start Guide

Windows 8.1 Control Panel 1 - 27

Desktop App

Quick Start Guide

Windows 8.1 Start Screen & Desktop

The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking

the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps.

Figure 1 - 17 - Windows Start Screen

1 - 28 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Click the arrow at the bottom of the screen to access All Apps

Apps & Tiles

The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.

Accessing Pining/Unpinning All Apps

You can add and remove the tiles for apps and control panels in the Start screen. Right-click on an app to bring up the context menu and you pin the App to (or unpin from) the Start screen, or to the taskbar.

Figure 1 - 18 - Apps

Windows 8.1 Start Screen & Desktop 1 - 29

Move the mouse to the bottom left of the screen and click to switch back to the Start screen.

Quick Start Guide

Desktop Application

When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click.

Figure 1 - 19 - Desktop

1 - 30 Windows 8.1 Start Screen & Desktop

The Charms Bar

Move the mouse over a Charms Bar icon to activate the menu

Move the mouse to the top/lower right icons to activate the Charms Bar

The right side of the screen (Start or Desktop) displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower

right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.

Quick Start Guide

Figure 1 - 20 - Start Screen with Charms Bar

Windows 8.1 Start Screen & Desktop 1 - 31



Charms Bar - TouchPad Access

To quick access the Charms Bar using the TouchPad:

1. Place your finger off the TouchPad (slightly to the right of the pad resting on the computer).

2. Move your finger across to the left on to the TouchPad.

3. The Charms Bar will then pop-up.

Quick Start Guide

Charms Bar Items

• Search : You can search for any file, application, Apps and control panel settings with instantaneous

results.

•Share : This button is used to share information with people via mail or social networks.

•Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or click-

ing the bottom left of the screen).

• Devices : Click this button to change connected peripheral device settings e.g. an external display.

• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).

Figure 1 - 21 - Settings Menu

1 - 32 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Windows 8.1 Taskbar

In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar can be directly accessed from the Desktop application; if you

are in the Start screen you will need to move the cursor to the bottom of the screen to display the taskbar. The taskbar is displayed at the bottom of the screen, and you can see the notification area (system tray) of the

taskbar in the bottom right of the screen. Some of the control panels and applications referred to during the course of this manual can be accessed from here.

Figure 1 - 22 - Taskbar & Notification Area (System Tray)

You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing

Pining/Unpinning All Apps” on page 1 - 29).

Windows 8.1 Start Screen & Desktop 1 - 33

1. Attach your display to the appropriate port, and turn it on.

2. Go the Charms Bar, select Devices.

3. Click Project (you ma y need to click Second Screen).

4. Click on any one of the options from the menu to select PC screen only, Duplicate,

Extend or Second screen only.

Quick Start Guide

Video Features

Microsoft Hybrid Graphics

Microsoft Hybrid Graphics is a seamless technology designed to get best performance from the graphics system while allowing longer battery life, without having to manually change settings. The computer will automat- ically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use.

You can switch display devices, and configure display options, from the Display control panel (in Appearances

and Personalization) when running the Desktop app (see “Desktop App lication” on page 1 - 30 and Appendix

C). It is possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The Charms Bar” on page 1 - 31).

To Configure Displays from Devices (Charms Bar):

1 - 34 Video Features

Figure 1 - 23 - Devices (Project)

Quick Start Guide



Right-Click Desktop

App

1. You can right-click the desktop and select Screen reso- lution (Figure 1

- 24).

2. Use the dropbox to select the screen

Resolution

(Figure 1 - 24).

3.Click Advanced settings (Figure

1 - 24) to bring up

the Advanced properties tabs.

123

To access Display (Control Panel) and Screen Resolution in Windows:

1. Go to the Control Panel.

2. Click Display (icon) - In the Appearance and Personalization category.

3. Adjust resolution.

Figure 1 - 24 - Screen Resolution

Video Features 1 - 35

Quick Start Guide

To access the Intel(R) HD Graphics Control Panel:

1. Click Advanced settings (Figure 1 - 24 on page 1 - 35) in the Screen Resolution control panel in Windows.

2. Click the Intel(R)... tab and click Graphics Properties (button) (Figure 1 - 25 on page 1 - 36) .

3. Right-click the desktop and select Graphics Properties from the menu.

4. Click the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.

Figure 1 - 25 - Intel Graphics Control Panel

1 - 36 Video Features

To access the NVIDIA Control Panel:

1. Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 26).

2. Double-click the icon (Figure 1 - 26) in the Windows control panel.

Quick Start Guide

Figure 1 - 26 - NVIDIA Control Panel

Video Features 1 - 37

Charms Bar Desktop App Start Screen

Quick Start Guide

Power Options

Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set- tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 10). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc.

Shut Down, Restart or Sleep (Charms Bar)

1. Go to the Charms Bar and click Settings.

2. Click Power .

3. Select Sleep, Shut Down or Restart.

1 - 38 Power Options

Figure 1 - 27 - Shut Down/Restart

Quick Start Guide



Screen Resolution for Apps

(Windows 8.1)

The minimum resolution in which Apps will run is 1024x768. The minimum resolution required to support a ll the features of

Windows 8 (including multitasking with snap) is 1366x768. These specs are the minimum screen resolution that supports

all the features of Windows 8.1 on a useful physical size.

Running Apps

To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements.

Screen Resolution Settings

1. Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).

2. Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).

Figure 1 - 28 - Screen Resolution

Running Apps 1 - 39

Quick Start Guide

User Account Control Settings

If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below.

1. Open the Control Panel.

2. Click on User Accounts and then click on Change User Account Control settings (or click System and Security and click Change User Account Control Settings under Action Center).

3. If the slider is in the Never notify position, then the UAC is disabled.

4. To enable or turn on the UAC, move the slider to Always notify or Notify me when apps try to make changes

to my computer (default) position, and then click OK.

1 - 40 Running Apps

Figure 1 - 29 - User Account Control

Storage Devices, Mouse, & Audio

Chapter 2: Storage Devices, Mouse, & Audio

Overview

Read this chapter to learn more about the following main features and components of the computer:

• Hard Disk Drive/Solid State Drive

• Optical (CD/DVD) Device

• Audio Features

• Touchpad and Buttons/Mouse

Overview 2 - 1

Storage Devices, Mouse, & Audio



Bottom Cover

Removal Warning

Do not remove any cover(s) and /or screw(s) for the purposes of device upgrade as this may violate the terms of your warranty.

If you need to replace/ remove the hard disk for any reason, please contact your distributor/supplier for further information.

Hard Disk Drive/Solid State Drive

The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data in the computer. The hard disk can be taken out to accommodate other serial (SATA) hard disk drives (see “Storage” on page D - 3 for specification information), however you will need to contact your distributor/supplier to do this in order to avoid violating the terms of your warranty.

2 - 2 Hard Disk Drive/Solid State Drive

Storage Devices, Mouse, & Audio



Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Win- dows. Click the Volume icon on the notification area to check the setting (see “Audio Features”

on page 2 - 7).

Figure 2 - 1

Optical Device

123

2 3

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page D - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 14).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole

to open the tray.

Optical (CD/DVD) Device 2 - 3

Storage Devices, Mouse, & Audio



CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.

2 - 4 Optical (CD/DVD) Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Storage Devices, Mouse, & Audio

Figure 2 - 2

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - Western Europe, Japan, South

Africa, Middle East & Egypt

• Region 3 - South-East Asia, Taiwan, South

Korea, The Philippines, Indonesia, Hong Kong

• Region 4 - South & Central America, Mexico,

Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern Europe,

India & Most of Africa

• Region 6 - China

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click Device Manager (Hardware and Sound > Devices and Printers), then click the arrow next to DVD/CD-ROM drives.

3. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control p anel to allow you to adjust the regional code.

4. DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Optical (CD/DVD) Device 2 - 5

Storage Devices, Mouse, & Audio



Push-Push Card

Reader

The card reader features a push-in/push-out card insertion and ejection mechanism. Simply push the card to insert and eject it, however Ms Duo cards require an adapter.

Figure 2 - 3

Right View

1. Card Reader

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

Model A

Model B

Model C

Multi-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “Card Reader” on page 4 - 7).

Note: Some of these cards require PC adapters that are usually supplied with the cards.

2 - 6 Multi-in-1 Card Reader

Storage Devices, Mouse, & Audio



Volume Adjustment

The sound volume level can be set using the volume control in the Set-

tings menu in the Charms Bar.

Figure 2 - 4

Realtek Audio

Manager

See “HDMI Audio Configuration” on page C - 37 for a description of the audio configuration when connecting an HDMI supported display device. See “Sound Blaster Cinema 2 Profiles” on page 6 - 44 for more information on the THX TruStudio Pro Audio setup.

Right-click the icon to access the menu above, and then select Sound Manager.

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the notification area/control panel (right-click the notification area icon to bring up an audio menu and select Sound Manager). The volume may also be adjusted by means of the Fn + F5/F6 key combination (see Table 1 - 4, on page 1 - 16).

Audio Features 2 - 7

Storage Devices, Mouse, & Audio

Figure 2 - 5

Realtek Audio

Manager -

Recording Setup

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:

1. Click

2. Click Realtek HD Audio Manager (or right-click the notification area icon and

3. Click Microphone Effects (tab) in Microphone (tab), and then click to select

4. Click OK to close the control panel and save the settings.

Control Panel

select Sound Manager). Noise Suppression (button), or adjust the Recording Volume level to around 60,

to obtain the optimum recording quality.

and make sure you are in

Classic View

2 - 8 Audio Features

Storage Devices, Mouse, & Audio



Touchpad Cleaning

In order to improve pad performance it is necessary to keep the surface clean and free of fingerprints and marks etc.

Use a soft dry cleaning cloth to keep the pad surface clean.

Disabling the Pad

Use the Fn + F1 or Control Center button to disable the Touchpad.

Touchpad and Buttons/Mouse

The Touchpad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The Touchpad buttons function in much the same way as a two-button mouse.

Touchpad and Buttons/Mouse 2 - 9

Storage Devices, Mouse, & Audio



TouchPad Scrolling

This computer model series may feature different TouchPad versions.

These TouchPads may differ in their vertical scrolling function in most scrollable windows.

Some TouchPads require sliding the finger up and down on the right of the TouchPad to scroll the window. Other versions require tapping/holding down the finger at the top right or bottom right of the TouchPad to scroll the window.

Figure 2 - 6

Touchpad

Sensitivity



Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.

Touchpad Sensitivity

The mouse button zones at the bottom of the pad measure about 15mm fr om the bottom of the pad, and the left and right buttons are divided roughly down the mid-

dle as illustrated below. Press the left button zone for a left click, and right button zone for a right click action.

2 - 10 Touchpad and Buttons/Mouse

Storage Devices, Mouse, & Audio



Touchpad Disabling

If you want to use an external mouse/pointing device, and want to automatically disable the touchpad when the external device is plugged-in click (Mouse Properties > ELAN) “Dis-

able when external USB pointing device plug in”

You can also choose to Stop Device to disable the touchpad altogether (note you will need to attach an external device in order to be able to click Enable De- vice to restart the touchpad).

Figure 2 - 7

Mouse Properties

(ELAN tab) & Taskbar Icon

Elan TouchPad

Once you have installed the touchpad driver (see “Touchpad” on page 4 - 8) you can configure the functions by double-clicking the touchpad driver icon in the notification area of the taskbar (or from Options in the ELAN tab in the Mouse control panel in Windows). You may then configure the gestures and options to your preferences.

Touchpad and Buttons/Mouse 2 - 11

Storage Devices, Mouse, & Audio

Figure 2 - 8

Smart-Pad Control

Panel (Button)

The Elan Smart-Pad control panel allows you to use a specific gesture (action) on the surface of the touchpad to perform specific actions to manipulate documents, objects and applications.

Click the menu tabs (One-finger, Multi-finger or Additional) and then the function button on the left to access the Configuration controls in the right panel. Click the check box to Enable most of the controls and click Apply to save the settings. Click the close icon or Yes to close the control panel.

2 - 12 Touchpad and Buttons/Mouse

Storage Devices, Mouse, & Audio

Figure 2 - 9

Smart-Pad Control

Panel with

Function

Description

Click the Function Description button to get a detailed description of any function.

Click the Default button to set any of the functions to the default setting.

Touchpad and Buttons/Mouse 2 - 13

Storage Devices, Mouse, & Audio

Figure 2 - 10

Tapping

Figure 2 - 11

Clicking

One-Finger

Tapping

One-Finger tapping is equivalent to clicking the left mouse button to perform a point/click/select function.

Clicking

You can configure actions for two-finger, three-finger and left or right corner clicking actions from the clicking menu.

2 - 14 Touchpad and Buttons/Mouse

Storage Devices, Mouse, & Audio

Figure 2 - 12

Drag and Drop

Figure 2 - 13

Edge Scroll

Drag and Drop

You can select the different drag and drop methods from the menu provided. The object can be released when you lift the finger off the touchpad, when you tap again or after a set time delay.

Edge Scroll

Enable Vertical or Horizontal Scroll from this menu. You can configure the width of the scrollable area by adjusting the slider accordingly. To scroll vertically, tap the right edge of the touchpad and drag the finger up and down. To scroll horizontally, tap the bottom edge of the touchpad and drag your finger left or right.

Touchpad and Buttons/Mouse 2 - 15

Storage Devices, Mouse, & Audio

Figure 2 - 14

Edge Swipe

Enable Edge Swipe to use a single finger to scroll from the edges of the touchpad to perform the designated function in Windows 8.

2 - 16 Touchpad and Buttons/Mouse

Storage Devices, Mouse, & Audio

Figure 2 - 15

Zooming

Figure 2 - 16

Scrolling

Multi-Finger

Zooming

Place two fingers on the touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out.

Scrolling

The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Tap the pad surface and slide both fingers in the direction required (vertically or horizontally as long as the option is selected).

Note that the scrolling direction is opposite to that of a standard mouse wheel configuration.

Touchpad and Buttons/Mouse 2 - 17

Storage Devices, Mouse, & Audio

Figure 2 - 17

Rotation

Figure 2 - 18

Swipe Page

Rotation

You can rotate objects by using a two-finger gesture. Touch and rotate using two fingers on the pad in the direction required. Alternatively place a finger down on the pad and rotate the other finger around it in a circular motion (clockwise or counterclockwise).

Three Finger Swipe

This gesture is used to activate a Page Up/Page Down operation. Swipe three fingers quickly to the left to go to the previous page, or to the right to go to the next page. After you release your fingers from the pad the page changes, and make sure to lift your fingers immediately after the page change.

2 - 18 Touchpad and Buttons/Mouse

Storage Devices, Mouse, & Audio

Figure 2 - 19

Palm Tracking

Figure 2 - 20

Sensitivity

Additional

Palm Tracking

This feature helps guard against accidental contact such as palms resting on the pad. Use the slider to adjust the sensitivity of the feature as appropriate. If you are finding that resting your palms on the pad is causing unwanted pointer movemen t, move the slider towards Maximum (but not so far as to lose all sensitivity). If the pad becomes unresponsive, adjust the slider towards Minimum.

Sensitivity

Adjust the level of finger pressure required for the cursor to respond from this menu.

Touchpad and Buttons/Mouse 2 - 19

Storage Devices, Mouse, & Audio

2-20

Chapter 3: Power Management



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers:

• The Power Sources

• Turning On the Computer

• Power Plans

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.

Overview 3 - 1

Power Management



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.

1. Attach th e AC/DC adapter to the DC-in jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and connect the AC power cord to the AC/ DC adapter (make sure you use the adapter when first setting up the computer, as to safeguard the computer during shipping, the battery will be locked to not power the system until first connected to the AC/DC adapter).

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “Battery FAQ” on page 3 - 18).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 14.

3 - 2 The Power Sources

Turning On the Computer



Power Button as Stand by or Hibernate Button

You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring

the Power Buttons” on page 3 - 9 for details).

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.

Power Management

Turning On the Computer 3 - 3

Power Management

Figure 3 - 1

Shut Down/Restart

Charms Bar Desktop App Start Screen

Shutting the Computer Down

Note that you should always shut your computer down by choosing the Shut down

command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen

to bring up the menu). You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If

you want to add Hibernate/Sleep to the Power Menu see “Adding Hibernate/Sleep

to the Power Menu” on page 3 - 10.

3 - 4 Shutting the Computer Down

Power Plans



Resuming

Operation

See Table 3 - 1, on

page 3 - 11 for informa-

tion on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Figure 3 - 2

Power Plan

Advanced Settings

The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.

Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.

Power Management

Power Plans3-5

Power Management

Figure 3 - 3

Power Plans

Click to Show/Hide additional power plans

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

3 - 6 Power Plans

Clevo N150SC, N150SD, N155SC, N155SD User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Chapter 1: Quick Start Guide

Overview

Advanced Users

Beginners and Not-So-Advanced Users

Warning Boxes

Not Included

System Software

System Startup

Model Differences

LCD Panel Open - Model A

LCD Panel Open - Model B

LCD Panel Open - Model C

LED Indicators

Illuminated LED Keyboard

Control Center

Flexikey® Application

Flexikey® Application Features:

Keyboard Shortcuts

Function Keys & Visual Indicators

Front & Rear Views

Right View

Left View

Bottom View - Model A

Bottom View - Model B

Bottom View - Model C

Windows 8.1 Control Panel

Windows 8.1 Start Screen & Desktop

Apps & Tiles

Desktop Application

The Charms Bar

Windows 8.1 Taskbar

Video Features

Microsoft Hybrid Graphics

Power Options

Running Apps

Chapter 2: Storage Devices, Mouse, & Audio

Overview

Hard Disk Drive/Solid State Drive

Optical (CD/DVD) Device

Loading Discs

Handling CDs or DVDs

DVD Regional Codes

Multi-in-1 Card Reader

Audio Features

Setup for Audio Recording

Touchpad and Buttons/Mouse

Touchpad Sensitivity

One-Finger

Multi-Finger

Additional

Chapter 3: Power Management

Overview

The Power Sources

AC/DC Adapter

Battery

Turning On the Computer

Shutting the Computer Down

Power Plans