Clevo M810L, M811L User guide

V09.5.11

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©September 2009

Trademarks

Intel and Atom are trademarks/registered trademarks of Intel Corporation.

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interference that may cause undesired operation of the

device.

Preface

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

III

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 -

240V, 50 - 60Hz, DC Output 19V, 1.57A/1.58A).

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive heat or direct sunlight.

Do not leave it in a place where foreign matter or moisture may affect the system.

Don’t use or store the computer in a humid environment.

Do not place the computer on any surface that will block the Vents/Fan Intakes.

Preface

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he comput er. Shut the computer down properly and don’t for ge t

to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

5. Take care when using peripheral devices.

Use only approved brands of peripherals.

Do not disassemble the computer by yourself.

Unplug the power cord befor e attaching peripheral devices.

Perform routine maintenance on your computer.

Power Safety

The computer has specific power requirements:

Preface

• Only use a power adapter approved for use with this computer.

• Your AC/DC adapter may be designed for international travel but it still requires a

steady , uninterru pted power suppl y. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third

prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not

by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current

load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power

supplies (i.e. AC/DC adapter or car adapter).

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.

VII

Preface

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qual-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

VIII

Preface

Cleaning

Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord or AC/DC adapter is damaged or frayed.

• If the computer has been exposed to rain or other liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before turning the computer on.

Preface

Travel Considerations

Packing

As you get ready for your trip, run through this list to make sure the system is ready to go:

1. Check that the battery pack and any spares are fully charged.

2. Power off the computer and peripherals.

3. Close the display panel and make sure it’s latched.

4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.

5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,

check with your travel agent to see if you need any socket adapters.

6. Put the notebook in its carrying bag and secure it with the bag’s straps.

7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters

and/or cables.

8. Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hard -

ware and software. Make sure your documents are prepared.



Power Off Before Traveling

Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prev ent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.

Preface

On the Road

In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:

Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.

Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.

Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.

Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.

Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.

Preface

Developing Good Work Habits

Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:

•Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.

•Your knees should be slightly higher than your hips. Place you r fe et fl at on the floor or on a footrest if necessary.

•Use a chair with a back and adjust it to support your lower back comfortably.

•Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.

• Take periodic breaks if you are using the computer for long periods of time.

Remember to:

•Alter your posture frequently.

•Stretch and exercise your body several times a day.

•Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.

XII

Preface

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idl e time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

XIII

Preface

XIV

Contents

Notice ................................................................................. I

FCC Statement ..................................................................II

FCC RF Radiation Exposure Statement: ........................ III

Instructions for Care and Operation ................................ V

Power Safety ..................................................................VII

Battery Precautions ......................................................VIII

Cleaning .......................................................................... IX

Servicing ......................................................................... IX

Travel Considerations ...................................................... X

Preface

System Map: Front & Rear Views ...............................1-10

System Map: Left & Right Views ...............................1-12

System Map: Bottom View ..........................................1-14

3.75G/HSPA Module USIM Card Installation ............1-15

Windows XP Start Menu & Control Panel ..................1-16

Video Features .............................................................1-17

Dynamic Video Memory Technology .........................1-17

Display & Graphics Properties ....................................1-18

Power Management Features .......................................1-19

Quick Start Guide

Overview ........................................................................1-1

Advanced Users .............................................................1-2

Beginners and Not-So-Advanced Users ........................1-2

Warning Boxes ..............................................................1-2

Not Included ..................................................................1-3

Model Differences .........................................................1-4

System Software .............................................. ..............1-4

System Startup ...............................................................1-5

System Map: LCD Panel Open - Model A ....................1-6

System Map: LCD Panel Open - Model B ....................1-7

Keyboard ........................................................................1-8

Function/Hot Key Indicators .........................................1-9

Features & Components

Overview ........................................................................2-1

Hard Disk Drive .............................................................2-2

External USB Optical (CD/DVD) Device .....................2-3

Loading Discs ................................................................2-3

Handling CDs or DVDs .................................................2-4

DVD Regional Codes ....................................................2-5

7-in-1 Card Reader .........................................................2-6

TouchPad and Buttons/Mouse .......................................2-7

Audio Features ...............................................................2-8

Audio Recording from Microphone ..............................2-9

Adding a Printer ................................................. .... ......2-10

USB Printer ..................................................................2-10

Preface

Parallel Printer .............................................................2-10

Power Management

Overview ........................................................................3-1

Advanced Configuration and Power Interface ..............3-1

The Power Sources ........................................................3-2

AC/DC Adapter .............................................................3-2

Battery ............................................................................3-2

Turning on the Computer ...............................................3-3

Power Schemes ..............................................................3-4

System Power Options ...................................................3-6

Hibernate Mode vs. Shutdown ......................................3-6

Stand by Mode vs. Hibernate Mode ..............................3-6

Stand by .........................................................................3-7

Hibernate ........................................................................3-7

Configuring the Power Button .......................................3-8

Battery Information ............................................. .... ......3-9

New Battery ...................................................................3-9

Battery Life .............................................................. .... ..3-9

Recharging the Battery with the AC/DC Adapter .......3-10

Proper handling of the Battery Pack ............................3-11

Battery FAQ ................................................. .... ............3-12

Drivers & Utilities

What to Install ................................................................4-1

Module Driver Installation .............................................4-1

Driver Installation ..........................................................4-2

Authorized Driver Message ...........................................4-4

New Hardware Found ....................................................4-4

Version Conflict Message ..............................................4-4

Updating/Reinstalling Individual Drivers ......................4-4

Driver Installation Procedure ......................................... 4-5

Chipset ...........................................................................4-5

Video ..............................................................................4-5

Audio .............................................................................4-5

LAN ...............................................................................4-5

TouchPad .......................................................................4-5

Card Reader ...................................................................4-5

Hot Key ..........................................................................4-6

Optional Drivers ............................................................4-6

Bluetooth Module ..........................................................4-6

PC Camera Module ........................................................4-6

Wireless LAN Module ...................................................4-6

3.75G/HSPA Module .....................................................4-6

BIOS Utilities

Overview ........................................................................5-1

The Power-On Self Test (POST) ................................... 5-2

Failing the POST ................................................... ... .....5-3

Fatal Errors ............................................ ........................5-3

XVI

Preface

Non-Fatal Errors ............................................................5-3

The Setup Utility ...................................................... .... ..5-4

Entering Setup ...............................................................5-4

Setup Screens .................................................................5-5

Main Menu .....................................................................5-6

System Time & Date (Main Menu) ...............................5-6

SATA Port 1 (Main Menu) ............................................5-7

System/Extended Memory (Main Menu) ......................5-7

Advanced Menu .............................................................5-8

Installed O/S (Advanced Menu) ....................................5-8

SATA Mode Selection (Advanced Menu) ....................5-9

Legacy USB Support (Advanced Menu) .......................5-9

Boot-time Diagnostic Screen (Advanced Menu) ...........5-9

Reset Configuration Data (Advanced Menu) ................5-9

Power On Boot Beep (Advanced Menu) .....................5-10

Battery Low Alarm Beep (Advanced Menu) ...............5-10

Detect External CRT (Advanced Menu) .....................5-10

Enhance USB ODD detection (Advanced Menu) .......5-10

Security Menu ..............................................................5-11

Set Supervisor Password (Security Menu) ..................5-11

Set User Password (Security Menu) ............................5-12

Password on boot (Security Menu) ..............................5-12

Fixed disk boot sector (Security Menu) .......................5-12

Boot Menu ...................................................................5-13

Exit Menu ....................................................................5-14

Upgrading The Computer

Overview ........................................................................6-1

When Not to Upgrade ....................................................6-2

Removing the Battery ....................................................6-3

Upgrading the HDD .......................................................6-4

Hard Disk Removal - Model A Computers ...................6-5

Hard Disk Removal - Model B Computers ...................6-8

Upgrading the System Memory (RAM) ......................6-10

Upgrading the Processor ..............................................6-13

Modules & Options

Overview ........................................................................7-1

Bluetooth Module ..........................................................7-2

Bluetooth Configuration in Windows XP ......................7-4

To Add a Bluetooth Device ...........................................7-5

PC Camera Module ........................................................7-7

PC Camera Driver Installation .......................................7-8

Wireless LAN Module .................................................7-14

3rd Party 802.11b/g or 802.11b/g/n WLAN

Driver Installation ........................................................7-17

3.75G/HSPA Module ...................................................7-18

3G Watcher ..................................................................7-20

3G Watcher Application Installation ...........................7-20

Setting Up a Carrier Profile .........................................7-21

Short Messaging Service .............................................7-26

XVII

Preface

HSPA Modem Interface ..............................................7-27

HSPA Modem Interface Installation ...........................7-27

HSPA Modem Interface ..............................................7-28

Adding a Profile ...........................................................7-30

Contacts .......................................................................7-32

Messages ...................................................................... 7-33

Settings ........................................................................7-34

Mobile Partner .............................................................7-36

Mobile Partner Application Installation ......................7-36

Mobile Partner Application .........................................7-37

Profile Management ................................................. ....7-37

Text Messaging Service ...............................................7-41

Troubleshooting

Overview ........................................................................8-1

Basic Hints and Tips ......................................................8-2

Backup and General Maintenance .................................8-3

Viruses ........................................................................... 8-4

Upgrading and Adding New Hardware/Software ..........8-5

Problems and Possible Solutions ...................................8-7

Interface (Ports & Jacks)

Notebook Ports and Jacks .............................................A-2

Intel Video Driver Controls

Intel Video Driver Installation ......................................B-1

Video .............................................................................B-1

Dynamic Video Memory Technology ..........................B-1

Intel Graphics Properties ..............................................B-2

Scheme Options ......................................... ...................B-4

Display Devices & Options ..........................................B-5

Attaching Other Displays ..............................................B-6

Specifications

Processor ....................................................................... C-2

Core Logic ....................................................................C-2

Display .......................................................................... C-2

Memory .........................................................................C-2

Video Adapter ...............................................................C-2

BIOS .............................................................................C-2

Storage .......................................................................... C-2

Security ......................................................................... C-2

Audio ............................................................................C-2

Pointing Device .............................................................C-2

Keyboard .......................................................................C-2

Operating System ..........................................................C-3

Card Reader ..................................................................C-3

Slot ................................................................................ C-3

Dimensions & Weight ........................................... .......C-3

XVIII

Preface

Optional ........................................................................ C-4

Windows 7 Information

Windows 7 Start Menu & Control Panel ......................D-2

Video Features ..............................................................D-3

Screen Resolution..........................................................D-4

Attaching Other Displays .............................................D-5

Windows 7 Driver Installation ......................................D-7

Updating/Reinstalling Individual Drivers......................D-9

Driver Installation Procedure.......................................D-10

Chipset ........................................................................ D-10

Video ...........................................................................D-10

Audio ..........................................................................D-10

LAN ............................................................................D-10

TouchPad .................................................................... D-10

Card Reader ......................................................... .... ...D-10

Hot Key .......................................................................D-11

Optional Drivers ..........................................................D-11

PC Camera Module......................................................D-12

PC Camera Driver Installation ....................................D-13

Wireless LAN Module.................................................D-14

Intel® Wi-Fi Link Series Driver Installation ..............D-15

3rd Party 802.11b/g or 802.11b/g/n WLAN

Driver Installation .......................................................D-15

3.75G/HSPA Module...................................................D-16

HSPA Modem Interface Installation ...........................D-18

Mobile Partner Application Installation .....................D-19

Other Notes: ................................................................D-20

XIX

Preface

Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, 7-in-1 card reader), TouchPad & Mouse, Audio & Printer.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s Bluetooth, PC Camera, Wireless LAN and 3.75G/HSPA mod-

ules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the Intel Video driver controls.

• Appendix C The computer’s specification.

• Appendix D Windows 7 driver installation information.

Overview 1 - 1

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on

page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

the information contained in the Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide

Not Included

Operating Systems (e.g. Windows XP/Windows 7) and applications (e.g. word processing, spreadsheet and da- tabase programs) have their own manuals, so please consult the appropriate manuals.



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed. You will be unable to use most advanced controls until the necessary drivers and utilities are prope rly installed. If your system hasn’t been properly configured (your service representative may have already done that for you); refer to

Chapter 4 for installation instructions.

Ports and Jacks

See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Overview 1 - 3

Quick Start Guide

Model Differences

This notebook series includes el’s appearance may appear slightly different from those pictured throughout this manual.

two

different model types which differ slightly in design style. Note that your mod-

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are supported. See “Installed O/S (Advanced Menu)” on page 5 - 8 for information on setting the O/S in the BIOS before installing the operating system.

Operating System & Version Note

Windows XP (Home or Professional)

with Service Pack 3

Windows 7 *See Appendix D for driver installation information on Windows 7.

Table 1 - 1 - Operating Systems Supported

In order to run Windows XP without limitations or decreased performance, your computer requires a minimum 512MB of system memory (RAM)



Windows Vista Service Pack 3

Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3) before installing any drivers. Go to the Microsoft website for download details, or contact your service center.

1 - 4 Overview

Quick Start Guide

System Startup

1. Remove all packing materials, and place the computer on a stable surface.

2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.

3. Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an

outlet, and connect the AC power cord to the AC/DC adapter.

4. Use one hand to carefully raise the lid/LCD to a comfortable viewing angle, while using the other hand (as illustrated

Figure 1 - 1

5. Press the power button to turn the computer “on”.

Note that you should always shut your computer down by choosing the Turn Off Computer command from the Start menu in Windows. This will help prevent hard disk or system problems.

below) to support the base of the computer (



Shutdown

Note: Never

lift the computer by the lid/LCD).

Figure 1 - 1 - Opening the Lid/LCD/Computer with AC/DC Adapter Plugged-In

System Startup 1 - 5

Quick Start Guide

Figure 1 - 2

LCD Panel Open

Model A

1. Built-In PC Camera (

Optional

)

2. LCD

3. Speakers

4. Keyboard

5. Built-In Microphone

6. Touchpad & Buttons

System Map: LCD Panel Open - Model A

Operation Aboard

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.

Use the key combinations to toggle power to the WLAN/ Bluetooth modules, and check the LED indicator icon to see if the modules are powered on or not (see Table 1 -

2, on page 1 - 9/ Table 1 - 3, on page 1 - 11).



Wireless Device

Aircraft

1 - 6 System Map: LCD Panel Open - Model A

Quick Start Guide

System Map: LCD Panel Open - Model B

Operation Aboard

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer aboard aircraft.

Use the key combinations to toggle power to the WLAN/ Bluetooth modules, and check the LED indicator icon to see if the modules are powered on or not (see Table 1 -

2, on page 1 - 9/ Table 1 - 3, on page 1 - 11).



Wireless Device

Aircraft

Figure 1 - 3

LCD Panel Open

Model B

1. Built-In PC Camera (

Optional

)

2. LCD

3. Speakers

4. Keyboard

5. Built-In Microphone

6. Touchpa d & Buttons

System Map: LCD Panel Open - Model B 1 - 7

Quick Start Guide

Keyboard

The keyboard has a numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly. See Table 1 - 2, on page 1 - 9 for details on the function keys.



Special Characters

Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.

Figure 1 - 4 - Keyboard



Other Keyboards

If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. Th e system will detect and enable it automatically. However spe cial func tions/ho t-keys unique to the system’s regular keyboard ma y not work.

1 - 8 Keyboard

Quick Start Guide

Function/Hot Key Indicators

The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators are available when the hot key utility provided is installed. When the driver is installed, an icon will appear in the taskbar.

Keys Function Keys Function

Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F8/F9

Fn + F1

Fn + F2

Fn + F3

Fn + F4 Sleep Toggle

Fn + F5/F6

Fn + F7 Display Toggle

TouchPad Toggle

(Press a key to or use TouchPad to turn on)

Volume Decrease/Increase

Turn LCD Backlight Off

Mute Toggle

Fn + F10

Fn + F11

Fn + F12

Fn +

Fn + NumLk

Fn + ScrLk

Caps Lock

Table 1 - 2 - Function & Hot Key Indicators

Brightness Decrease/Increase

PC Camera Power Toggle

WLAN Module Power Toggle

Bluetooth Module Power Toggle

3.75G/HSPA Module Power Toggle

Number Lock Toggle

Scroll Lock Toggle Caps Lock Toggle

Function/Hot Key Indicators 1 - 9

Quick Start Guide

Figure 1 - 5

Front & Rear Views

1. LED Power & Communication Indicators

2. 7-in-1 Card Reader

3. Microphone-In Jack

4. Headphone-Out Jack

5. Battery

System Map: Front & Rear Views



7-in-1 Card Reader

The card reader allows you to use the most popular digital storage card formats:

MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) /

MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) /

Mini SD (requires PC adapter) / RS MMC (requires PC adapter)

Model A

Model B

432

Model B

1 - 10 System Map: Front & Rear Views

Icon Color Description

Orange DC Power is Plugged In

Green The Computer is On

Blinking Green The Computer is in Sleep Mode

Orange The Battery is Charging

Green The Battery is Fully Charged

Blinking Orange The Battery Has Reached Critically Low Power Status

Green Hard Disk Activity Green The (optional) Wireless LAN Module is Powered On

Orange The (optional) Bluetooth Module is Powered On

Table 1 - 3 - LED Indicators

Quick Start Guide

System Map: Front & Rear Views 1 - 11

Quick Start Guide

Figure 1 - 6

Left & Right Views

1. Security Lock Slot

2. DC-In Jack

3. RJ-45 LAN Jack

4. 2 * USB 2.0 Ports

5. External Monitor Port

6. Hard Disk Drive Bay

7. Vent/Fan Intake/ Outlet

8. Power Button (Model A Computers Only)

System Map: Left & Right Views

Model A

Model B

1 - 12 System Map: Left & Right Views

Quick Start Guide



External Optical (CD/DVD) Device Drives

To install applications and drivers etc. you will need to attach an external optical CD/DVD device to the USB ports. If you are having problems detecting external ODDs, enable the enhanced detection of these devices see “Enhance USB ODD detection (Advanced

Menu)” on page 5 - 10.



Overheating

To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.

System Map: Left & Right Views 1 - 13

Quick Start Guide

Figure 1 - 7

Bottom View

1. Battery

2. Vent/Fan Intake/ Outlet (Model B Computers Only)

3. Hard Disk Bay (Model B Computers Only)



CPU

The CPU is not a user serviceable part. Opening this compartment, or accessing the CPU in any way, may violate your warranty.

System Map: Bottom View

Model A

Model B



3.75G/HSPA Module USIM Card

The 3.75G/HSPA module’s USIM card location is located under the battery compartment. See page 1 - 15 for instructions on installing the

3.75G/HSPA USIM card.

Battery Information

Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

1 - 14 System Map: Bottom View

Quick Start Guide

3.75G/HSPA Module USIM Card Installation

If you have included an optional 3.75G/HSPA module in your purchase option, follow the instructions below to install the USIM card (which will be provided by your service provider), and then run the 3G Watcher/HSPA Modem Interface application. See “3G Watcher” on page 7 - 20/“HSPA Modem Interface” on page 7 - 27/

“Mobile Partner” on page 7 - 36 for instructions on installing the program etc.

1. Turn off the computer, and turn it over and then remove the battery (slide the latches in the direction indicated below and slide the battery out).

2. Insert the USIM card as illustrated below until it clicks fully into position, and replace the battery.

Model A

Model B

Figure 1 - 8 - Battery Removal & USIM Card Insertion

System Map: Bottom View 1 - 15

Model A

Model B

Quick Start Guide

Windows XP Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can cu stomize the look of the Start menu by right-clicking the Start menu and selecting Properties from the menu.

Click here to toggle Category View

Figure 1 - 9 - Start Menu & Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features

in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see all controls it may be necessary to toggle off Category View.

1 - 16 Windows XP Start Menu & Control Panel

Quick Start Guide

Video Features

You can switch display devices, and configure display options, from the Display Properties control panel in

Windows as long as the appropriate video driver is installed. For more detailed video information see “Intel

Video Driver Controls” on page B - 1.

To access Display Properties in Windows:

1. Click Start, point to Settings and click Control Panel (or just click Control Panel).

2. Double-click Display (icon) - In the Appearances and Themes category.

3. Click Settings (tab) in the Display Properties dialog box.

4. Move the slider to the preferred setting in Screen resolution (Figure 1 - 10 on page 1 - 18).

5. Click the arrow, and scroll to the preferred setting in Color quality (Figure 1 - 10 on page 1 - 18).

6. You can also access Display Properties by right-clicking the desktop and scrolling down and clicking Properties. Click Settings (tab) and adjust as above.

7. Open the Display Properties control panel, and click Advanced (button) (Figure 1 - 10 on page 1 - 18) to bring up the Advanced properties tabs.

8. Click the Intel(R) Graphic s Media Ac ce le rat or Dr iv er for Mobile tab, and click Graphics Properties (button) to make any video adjustments you require.

9. You can also access Graphics Properties from the Windows Intel(R) GMA Driver for Mobile control p anel, or from the taskbar icon .

Dynamic Video Memory Technology

Intel® DVMT automatically and dynamically allocates as much (up to 128MB) system memory (RAM) as needed to the video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system.

Video Features 1 - 17

Quick Start Guide

Display & Graphics Properties



Taskbar Icon

You can also access the controller properties from the taskbar. Click on the icon to bring up the menu and scroll to Graphics Properties.

If you cannot see the tray icon go to the Intel(R) Graphics

Media Accelerator Driver for Mobile tab and click the

“Show Tray Icon” tickbox. Alternatively right-click the desktop and select Graphics

Options > Tray Icon > Enable.

1 - 18 Video Features

Figure 1 - 10 - Display & Graphics Properties

Quick Start Guide

Power Management Features

The Power Options control panel icon in Windows allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 11).

Figure 1 - 11 - Power Options

The computer’s power button, sleep button (Fn + F4 key combination), and lid (closing the lid) may be set to send the computer in to either Standby or Hibernate mode.

Power Saving and Performance

Power Schemes may have an affect on your computer performance.

Power Management Features 1 - 19

Quick Start Guide

1 - 20

Features & Components

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components of the computer:

•Hard Disk Drive

• External USB Optical (CD/DVD) Device

• 7-in-1 Card Reader

• TouchPad and Buttons/Mouse

• Audio Features

• Adding a Printer

Overview 2 - 1

Features & Components

Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.



Power Safety

Figure 2 - 1

HDD Bay

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) HDDs with a height of 9.5 mm.

The HDD is located in the bay on the right of your computer, and this can be opened after elevating the keyboard and accessing the screw securing the hard disk assembly. For further details see “Upgrading the HDD” on page 6 - 4.

Model A

Model B

Hard Disk Drive Bay



Hard Disk Drive Speeds

If you are going to upgrade/replace the hard disk drive, note that It is recommended that HDDs of a

maximum speed of 5400 RPM are used. DO NOT use 7200rpm or higher HDDs.

Note that the HDD bay can be accessed by elevating the keyboard (see “Upgrading

the HDD” on page 6 - 4).



HDD Bay

2 - 2 Hard Disk Drive

Features & Components

External USB Optical (CD/DVD) Device

An external USB optical (CD/DVD) device is available as an option for this computer. The optical device may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 13).

Loading Discs

To insert a CD/DVD, simply slide the disc into the disc slot with label-side facing up. The busy indicator will light up while data is being accessed, or while a disc is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole to eject the disc.



External Optical (CD/DVD)

Device Drives

ODD detection (Advanced Menu)” on page 5 - 10.



USB Cables

You can connect the optional USB optical device using one of the USB cables. However if you are experiencing connection or power problems, connect both USB cables from the device to the computer.

Figure 2 - 2

Optional Optical

Device Drive

External USB Optical (CD/DVD) Device 2 - 3

Features & Components

CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.



Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Handling CDs or DVDs

2 - 4 External USB Optical (CD/DVD) Device

Features & Components

DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-

ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.

DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

DVD Regional Coding

Region Geographical Location

1 USA, Canada 2 Western Europe, Japan, South Africa, Middle East & Egyp t

4 South & Central America, Mexico, Australia, New Zealand 5 N Korea, Russia, Eastern Europe, India & Most of Africa

6 China

South-East Asia, Taiwan, South Korea, The Philippines,

Indonesia, Hong Kong

Table 2 - 1

DVD Regional Coding

External USB Optical (CD/DVD) Device 2 - 5

Features & Components

Card Reader Cover

Make sure you keep the rubber cover provided in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.



7-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see “Card Reader” on page 4 - 5).

• MMC (MultiMedia Card)

• SD (Secure Digital)

• MS (Memory Stick)

• MS Pro (Memory Stick Pro)

• MS Duo (requires PC adapter*)

• Mini SD (requires PC adapter*)

• RS MMC (requires PC adapter*)

*Note: The PC adapters are usually supplied with these cards.

Figure 2 - 3

Right View

1. Card Reader

2 - 6 7-in-1 Card Reader

Features & Components

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. Make sure you have installed the TouchPad driver (see “TouchPad” on page 4 - 5).

You can configure the mouse functions from the Mouse Properties control panel. Click Start, point to Settings and click Control Panel (or just click Control Panel), and then double-click Mouse.

Click Hardware (tab) and double-click Properties to access Advanced Settings.



Mouse Driver

If you are using an external mouse your operating system may be able to auto-configure your mouse during its installation or only enable its basic functions. Be sure to check the device’s user documentation for details.

Figure 2 - 4

Mouse Properties

TouchPad and Buttons/Mouse 2 - 7

Features & Components



Audio Features

You can configure the audio options on your computer from the Sounds and Audio

Sound Volume

Adjustment

How high the sound volume can be set depends on the setting of the volume control within Windows (and the volume control function keys on the computer). Click the Volume icon on the taskbar to check the setting.

Devices Windows control panel, or from the Realtek HD Audio Manager icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination.

Figure 2 - 5

Realtek HD Audio

2 - 8 Audio Features

Features & Components

Audio Recording from Microphone

If you want to record from either the built-in microphone or an external microphone, then configure the audio options as follows:

1. Double-click the Realtek HD Audio Manager icon in the taskbar/control panel.

2. Click Mixer (tab).

3. Click the button under Mic Volume to select it (you can boost the volume level as high as required).

4. Click OK to close the control panel.

Figure 2 - 6

Mixer - Mic Volume

Audio Features 2 - 9

Features & Components

After setting up the printer attach the parallel cable to the printer.

Connect the printer’s parallel cable to the Parallel to USB converter, and then plug the converter into the USB port.

Turn ON the printer, then turn ON the computer.

Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.



Parallel Printer

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options.

USB Printer

Most current printers have a USB interface connection. You may use any one of the ports to connect the printer.

Install Instructions:

1. Set up the printer according to its instructions (unp acking, p aper tray, toner/ink cartridge etc.).

2. Turn ON the computer.

3. Turn ON the printer.

4. Connect the printer’s USB cable to one of the USB ports on the comp uter.

5. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the sidebar, however you will need to purchase a parallel to USB converter.

2 - 10 Adding a Printer

Power Management

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers:

• The Power Sources

• Turning on the Computer

• Power Schemes

• System Power Options

• Configuring the Power Button

• Battery Information

Advanced Configuration and Power Interface

The ACPI interface provides the computer with enhanced power saving techniques and gives the operating system (OS) direct control over the power and thermal states of devices and processors. For example, it enables the OS to set devices into lowpower states based on user settings and information from applications. ACPI is fully supported in Windows XP.



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows XP OS.)

Overview 3 - 1

Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.

1. Attach th e AC/DC adapter to the DC-in jack on the left of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.

3. Raise the lid/LCD to a comfortable viewing angle.

4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 12).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 9.

3 - 2 The Power Sources

Turning on the Computer

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options in the Windows control panel to configure this feature.



Forced Off

If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.

Power Button as Stand by or Hibernate Button

If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring the Po wer Button” on

page 3 - 8 for details).

Power Management



Shutdown

Note that you should always shut your computer down by choosing the

Turn Off Computer

command from the Start menu in Windows. This will help prevent hard disk or system problems.

Turning on the Computer 3 - 3

Power Management

Power Schemes



Resuming Operation

Press a key on the keyboard, or move the mouse/TouchPad to resume from Monitor or Hard Disk Stand by.

Figure 3 - 1

Power Schemes

You can set your computer to conserve power through individual components by means of Power Schemes. You can also adjust the settings for each scheme to set the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if the system reads or writes data, the hard disk motor will be turned back on). The schemes may also be set to set a specified time for the system to enter Stand by or Hibernate modes (see “System Power Options” on page 3 - 6).

3-4Power Schemes

Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose the Home/Office Desk scheme for maximum performance when the com- puter is powered from an AC power source. Choose the Max Battery scheme (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered. Windows will use Portable/Laptop as the default scheme.

Power Management

Power Schemes 3 - 5

Power Management

System Power Options



Stand by/Hibernate

or Shutdown Error

The computer may stop responding when you put it into (or resume from) Stand By or Hibernate, or when you shut down.

You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see Figure 3 - 2 on page 3 - 7).

Hibernate Mode vs. Shutdown

Hibernate mode and Shutdown are the same in that the system is off and you need to press the power button to turn it on. Their main difference is:

This error is caused by power management within Windows XP, when applied to a PC Camera attached to the internal USB hub.

Microsoft has posted a Hotfix for this error on its website (search for Hotfix KB909667).

Download and install the Hotfix to correct this error.

When you come back from hibernation, you can return to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.

You can use either method depending on your needs.

Stand by Mode vs. Hibernate Mode

If you want to stay away from your work for just a while, you can put the system on Stand by instead of in hibernation. It takes a longer time to wake up the system from Hibernate mode than from Stand by mode.

3 - 6 System Power Options

Stand by

Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle at its slowest speed. All open applications are retained in memory. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Stand by mode to save power.

Hibernate

Hibernate uses no power and saves all of your information on a part of the HDD before it turns the system off. Although it saves the most power it takes the longest time to return to full operation. You can set your computer to automatically enter Hibernate mode when the battery power is almost depleted. You will need to enable Hibernate mode from the Hibernate tab in the Power Options control panel. The system will resume from Hibernate mode by pressing the power button.

Power Management



System Resume

The system can resume from Stand by mode by:

• Pressing the power button

• Pressing the Sleep/ Resume key combination

• An incoming call received on the modem (if enabled)

• Network card (Wake On LAN) activity (if enabled)

Figure 3 - 2

Enable Hibernation

System Power Options 3 - 7

Power Management

Configuring the Power Button



Sleep Button

You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illustrated. In Windows this is referred to as the Sleep button.

Figure 3 - 3

Power Options

(Advanced - Power

Buttons)

The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode

the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. har d disk, monitor), the LED will remain green.

Power Button Sleep/ResumeLid

(Sleep) Button

3 - 8 Configuring the Power Button

Battery Information

Please follow these simple guidelines to get the best use out of your battery.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 12 for instructions on how to do this).

Battery Life

Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached. Power Options (you may set low battery Alarms and actions, and check the Power Meter from the Power Options control panel), and settings in the OS will help prolong the battery life if configured appropriately.

Power Management



Low Battery

Warning

When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.

Figure 3 - 4

Power Options

(Alarm & Power

Meter)

Battery Information 3 - 9

Power Management

Battery life may be shortened through improper maintenance. To optimize the life



Conserving Battery

Power

To conserve battery power: Lower the brightness level

of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.

and improve its performance, fully discharge and recharge the battery at least once every 30 days.

We recommend that you do not remove the battery yourself. If you need to remove the battery for any reason, see “Removing the Battery” on page 6 - 3.

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to Table 1 - 3, on

Close modem or communication applications when they are not being used.

Remove any unused PC Cards from the computer (PC Cards quickly use up battery power even if the system enters sleep mode).

Disconnect any unnecessary external devices.

page 1 - 11 for information on the battery charge status, and to “Battery Information” on page 3 - 9 for more information on how to maintain and properly recharge

the battery pack.)

3 - 10 Battery Information

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances

• DO NOT expose the battery to fire or high temperatures, it may explode

• DO NOT connect the metal terminals (+, -) to each other



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has bee n d roppe d we do not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is recommended that you replace your computer battery every two years.

Power Management

Battery Information 3 - 11

Power Management

Battery FAQ



Caution

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer by yourself even when you see a message that indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own. Disable the Power Options functions i n the Co ntrol Panel, especially any Alarms (unclick the tickboxes - see page 3 - 9) and Schemes (change all the settings to Never - see page 3 - 4). As the battery nears the end of its life save and close any critical files.

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

3 - 12 Battery Information

Chapter 4: Drivers & Utilities

Drivers & Utilities

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.

What to Install

The Device Drivers & Utilities + User’s Manual disc contains the drivers and utilities necessary for the proper operation of the computer.

Table 4 - 1, on page 4 - 3 lists what you need to install

and it is very important that the drivers are in- stalled in the order indicated.

See “Windows 7 Information” on page D - 1 for information on installing drivers for the Windows 7 OS.

Module Driver Installation

The procedures for installing drivers for the Wireless LAN, PC Camera and 3.75G/HSPA modules are

provided in “Modules & Options” on page 7 - 1.

Make sure any modules (e.g. PC Camera, WLAN or

3.75G/HSPA) are ON before installing the appropriate driver.

What to Install 4 - 1

Drivers & Utilities

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers/Option Drivers (button).

Follow the instructions to install the driver. Alterna-

tively click Start, navigate (Browse..) to the executable file and then follow the manual setup instructions.

1. Check the driver installation order from Table 4 - 1,

on page 4 - 3 (the drivers must be installed in

this order) which is the same as that listed in the

Drivers Installer menu below.

2. Click to select the driver you wish to install, after installing each driver it will become grayed out (if you need to reinstall any driver, click the Unlock button).

3. Follow the instructions for each individual driver installation procedure as listed on the following pages.

Figure 4 - 1 - Drivers Installer Screen 1

4 - 2 Driver Installation

Figure 4 - 2 - Drivers Installer Screen 2

Driver - Windows 7 Page #

Chipset Page 4 - 5 Video Page 4 - 5 Audio Page 4 - 5 LAN Page 4 - 5 TouchPad Page 4 - 5 Card Reader Page 4 - 5

Hot Key Page 4 - 6

Drivers & Utilities

Manual Driver Installation

Click Browse CD (button) in the Drivers Installer ap- plication and browse to the executable file in the appropriate driver folder.



Windows XP Service Pack 3

Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3)

before installing any drivers.

PC Camera Module Page 7 - 7 Wireless LAN Module Page 7 - 17

3.75G/HSPA Module Page 7 - 18

Table 4 - 1 - Driver Installation



External Optical (CD/DVD) Device Drives

Menu)” on page 5 - 10.

Driver Installation 4 - 3

Drivers & Utilities

Authorized Driver Message

If you receive a message telling you that the driver you are installing is not authorized (Digital Signature Not Found), just click Yes or Continue Anyway to ignore the message and continue the installation procedure.

You will receive this message in cases where the driver has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.

New Hardware Found

If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure as directed.

Version Conflict Message

During driver installation if you encounter any “file version conflict” message, please click Yes to choose to keep the existing (newer) version.

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Add/Remove Programs item. If you see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be necessary to restart the computer). Go to the appropriate section of the manual to complete the update/reinstall procedure for the driver in question.

If the driver is not listed in the Add/Remove Pro- grams item:

1. Click Start (menu), point to Settings and click Control Panel (or click Start > Control Panel).

2. Double-click System (icon); System (icon) is in Performance and Maintenance (category).

3. Click Hardware (tab) > Device Manager (button).

4. Double-click the device you wish to update/reinstall the driver for (you may need to click “+”).

5. Look for the Update Driver button (check the

Driver tab) and follow the on screen pr ompts.

4 - 4 Driver Installation

Drivers & Utilities

Driver Installation Procedure

Insert the Device Drivers & Utilities + User’s Manual disc and click Install Drivers (button), or click Option Drivers (button) to access the optional driver menu.



Driver Installation General Guidelines

As a general guide follow the default on screen instructions for each driver (e.g. Next > Next > Finish) unless you are an advanced user. In many cases a re start is required to install the driver.

Chipset

1. Click 1.Install Chipset Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer.

Video

1. Click 2.Install Video Driver > Yes.

2. Click Next > Yes > Next > Next.

3. Click Finish to restart the computer .

Audio

1. Click 3.Install Audio Driver > Yes.

2. Click Next > Yes.

3. Click Finish to restart the computer.

LAN

1. Click 4.Install LAN Driver > Yes.

2. Click Install > Finish to complete the installation.

3. The network settings can now be configured.

TouchPad

1. Click 5.Install Touch Pad Driver > Yes.

2. Select the installation language and click OK.

3. Click Next.

4. Click Finish > Yes to restart the computer.

Card Reader

1. Click 6.Install Cardreader Driver > Yes.

2. Click Install > Finish to complete the installation.

Driver Installation 4 - 5

Drivers & Utilities

Hot Key

1. Click 7.Install HotKey Driver > Yes.

2. Click Next > Install.

3. Click Finish > Finish to restart the computer.

Optional Drivers

See the pages indicated overleaf for the driver installation procedures for any modules included in your purchase option.

Bluetooth Module

Note: The operating system is the default setting for Bluetooth control in Windows XP, and does not require a driver. See “Bluetooth Module” on page 7 -

2 for configuration instructions.

PC Camera Module

See the introduction in “PC Camera Module” on

page 7 - 7, and check the installation procedure.

Wireless LAN Module

See the introduction in “Wireless LAN Module” on

page 7 - 14, and check the installation procedure.

3.75G/HSPA Module

See the introduction in “3.75G/HSPA Module” on

page 7 - 18, and check the installation procedure.

Figure 4 - 3 - Drivers Installer - Option Drivers Menu

4 - 6 Driver Installation

BIOS Utilities

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:

Diagnostics: The POST (Power-On Self Test)

Configuration: The Phoenix TrustedCore Setup Utility

If your computer has never been set up, or you are mak ing important chan ges to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.

There is one general rule: Don’t make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.



BIOS Screens

Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS.

BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.

Overview 5 - 1

BIOS Utilities

Phoenix TrustedCore(tm) NB Copyright 1985-2006 Phoenix Technologies Ltd. All Rights Reserved Bios Revision: ******** KBC/EC Firmware Revision: ******** CPU=1Processors Detected Intel(R) Atom(TM) CPU N270 @ 1.60GHz 1015M System RAM Passed 512 KB L2 Cache System BIOS shadowed Video BIOS shadowed Fixed Disk 0: FUJITSU MHY2120BH Mouse intialized

Press <F2> to enter SETUP

The Power-On Self Test (POST)



POST Screen

1.BIOS information

2.CPU type

3.Memory status

4.Enter Setup prompt appears only during

POST

Note:

The

POST

screen as pictured right is for guideline purposes only.

POST

The your computer may appear slightly different. If you disable the

time Diagnostic Screen

the POST screen will not appear.

screen on

Boot-

Figure 5 - 1

POST Screen

Each time you turn on the computer, the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory).

As the POST proceeds, the computer will tell you if there is anything wrong. If there is a problem that prevents the system from booting, it will display a system summary and prompt you to run Setup.

If there are no problems, the Setup prompt will disappear and the system will load the operating system. Once that starts, you can’t get into Setup without rebooting.

5 - 2 The Power-On Self Test (POST)

Failing the POST

Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.

Fatal Errors

These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.

Non-Fatal Errors

This kind of error still allows you to boot. You will get a message identifying the problem (make a note of this message!) followed by the prompt:

• Press <F1> to resume

• <F2> to enter Setup

Press F1 to see if the boot process can continue. It may work, without the correct configuration.

BIOS Utilities

Press F2 to run the Setup program and try to correct the problem. If you still get an error message after you change the setting, or if the “cure” seems even worse, call for help.

The Power-On Self Test (POST) 5 - 3

BIOS Utilities



BIOS Settings

Warning

The Setup Utility

The Phoenix TrustedCore Setup Utility tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).

Incorrect settings can cause your system to

malfunction. To correct mistakes, return to Set-

up and restore the Setup Defaults with <F9>.

5 - 4 The Setup Utility

Entering Setup

To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds after you turn on the system. If you get a “Keyboard Error”, (usually because you pressed F2 too quickly) just press F2 again.

If the computer is already on, reboot using the Ctrl + Alt + Delete combination and then hold down F2 when prompted. The Setup main menu will appear.

Setup Screens

The following pages contain additional advice on portions of the Phoenix TrustedCore Setup Utility.

BIOS Utilities



Setup Menus

Along the top of the screen is a menu bar with menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Phoenix TrustedCore Setup Utility.

Instructions on how to navigate each screen are in the box along the bottom of the screen. If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.

The Item Specific Help on the right side of each screen explains the highlighted item and has useful messages about its options.

If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.

The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configuration appropriate for your model and options.

The Setup Utility 5 - 5

BIOS Utilities

Main Advanced Security Boot Exit

F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Item Specific Help

<Tab>, <Shift Tab>, or <Enter> selects field.

Main

System Time:

[22:12:05]

System Date: [02/18/2009]



SATA Port 1 [FUJITSU MHV2120BH-(S]

System Memory 640 KB Extended Memory 1014 MB

BIOS Revision ******** KBC/EC Firmware Revision ********

Phoenix TrustedCore(tm) Setup Utility

Main Menu

Figure 5 - 2

Main Menu

System Time & Date (Main Menu)

The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.

5-6Main Menu

SATA Port 1 (Main Menu)

Pressing Enter opens the sub-menu to show the configuration of a HDD on the com- puter’s Serial ATA Port 1. Use the Auto (Type:) setting to have the items configured automatically for you.

System/Extended Memory (Main Menu)

This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.

BIOS Utilities

Main Menu 5 - 7

BIOS Utilities

Advanced Menu

Phoenix TrustedCore(tm) Setup Utility

Main AAdvanced Security Boot Exit

Installed O/S: [VISTA / Win 7]

SATA Mode Selection: [AHCI] Legacy USB Support: [Enabled]

Figure 5 - 3

Advanced Menu

Boot-time Diagnostic Screen: [Disabled] Reset Configuration Data: [No] Power On Boot Beep [Disabled] Battery Low Alarm Beep [Enabled]

Detect External CRT [Enabled] Enhance USB ODD detection [Disabled]

F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Installed O/S (Advanced Menu)

This setting tells the computer what kind of operating system you’re using. Make sure you choose the correct setting for your O/S in order to prevent system problems. Note: If you select the Vista/Win 7 O/S then the SATA Mode Selection menu will become available. If you are installing the Windows XP O/S make sure you have set the appropriate operating system here in order to prevent system problems.

Advanced

Only available if Windows Vista/Win 7

is selected as the O/S.

Item Specific Help

Select the operating system installed on your system which you will use most commonly.

Note: An incorrect setting can cause some operating systems to display unexpected behavior.

5 - 8 Advanced Menu

SATA Mode Selection (Advanced Menu)

This menu is only available if you select the Vista/Win 7 O/S as your operating system. You can configure SATA (Serial ATA) control to operate in either IDE (native/ compatible) or AHCI (Advanced Host Controller Interface) modes from this menu. The SATA mode should be set to AHCI mode for this system (unless you are sure your hard disk can only operate in IDE mode). If you are unsure of the mode your hard disk supports contact your service center.

Legacy USB Support (Advanced Menu)

Use this menu item to enable/disable the support for Legacy Universal Serial Bus in non-USB aware operating systems.

Boot-time Diagnostic Screen (Advanced Menu)

Use this menu item to enable/disable the Boot-time Diagnostic Screen or POST screen (see “The Power-On Self Test (POST)” on page 5 - 2).

Reset Configuration Data (Advanced Menu)

This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.

BIOS Utilities



SATA Mode

Selection

If you have installed the

Windows Vista/ Windows 7 operating sys-

tem with AHCI mode enabled (default setting), DO NOT disable AHCI mode (if you wish to disable AHCI mode you will need to reinstall the Windows Vista/ Windows 7 OS).

Advanced Menu 5 - 9

BIOS Utilities

Power On Boot Beep (Advanced Menu)

Use this menu item to enable/disable the beep as the computer starts up.

Battery Low Alarm Beep (Advanced Menu)

Use this menu item to enable/disable the audible warning when the battery has reached low power status.

5 - 10 Advanced Menu

Detect External CRT (Advanced Menu)

This menu allows you to Enable/Disable detection for External CRT’s (external displays). You can disable detection to save system power.

Enhance USB ODD detection (Advanced Menu)

This menu allows you to Enable/Disable enhanced detection for External USB ODD (optical device drives e.g. DVD drives). You can disable detection to speed up

boot time, or enable it if you are having problems with detecting any attached USB ODDs.

BIOS Utilities

bed

Security Menu

Main Advanced SSeeccuurriittyyBoot Exit

Supervisor Password Is: Clear User Password Is: Clear

Set Supervisor Password [Enter]

Set User Password [Enter]

Password on boot: [ Fixed disk boot sector: [Normal]

F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Phoenix TrustedCore(tm) Setup Utility

Set Supervisor Password (Security Menu)

You can set a password for access to the Phoenix TrustedCore Setup Utility. This will not affect access to the computer OS (only the Phoenix TrustedCore Setup Utility).

Security

Item Specific Help

Supervisor Password controls access to the setup utility.

]



Security Menu

The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your software OS.

Figure 5 - 4

Security Menu

Security Menu 5 - 11

BIOS Utilities

Set User Password (Security Menu)



Password Warning

If you set a boot password (Password on boot is “Enabled“), NEVER forget your password.

The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

You can set a password for user mode access to the Phoenix SecureCore Setup Utility. This will not affect access to the computer OS, (only the Setup utility) unless you choose to set a Password on Boot (see below). Many menu items in the Phoenix SecureCore Setup Utility cannot be modified in user mode. You can only set the

user password after you have set the supervisor password.

Password on boot (Security Menu)

Specify whether or not a password should be entered to boot the computer (you may only set a password on boot if a supervisor password is enabled). If “Enabled” is selected, only users who enter a correct password can boot the system (see the warning in the sidebar). The default setting is “Disabled”.

Fixed disk boot sector (Security Menu)

If you choose “Write-Protect” this will protect against viruses being written to the hard disk boot sector (this is not a substitute for installing an anti- virus program - see

“Viruses” on page 8 - 4).

Note: To clear existing passwords press Enter and type the existing password, then press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance.

5 - 12 Security Menu

Boot Menu

Phoenix TrustedCore(tm) Setup Utility

Main Advanced Security

Boot priority order:

1: IDE HDD: FUJITSU MHY212BH-(S1)

2: USB KEY: 3: USB FDC: 4: USB CDROM: 5: USB HDD: 6: PCI BEV: KMC26X Fast Ethernet Contr 7: 8:

Excluded from boot order:

: USB ZIP:

F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

When you turn the computer on it will look for an operating system (e.g. Windows Vista) from the devices listed in this menu, and in this priority order. If it cannot

find the operating system on that device, it will try to load it from the next device in the order specified in the Boot priority order. Item specific help on the right is available to help you move devices up and down the order.

Boot

Exit

Item Specific Help

Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. <x> exclude or include the device to boot. <Shift + 1> enables or disables a device.

BIOS Utilities



BIOS Screens

Note that the BIOS screens pictured on these pages are intended for guidance in setting up your system’s BIOS.

BIOS versions are subject to constant change and revision, therefore your computer’s actual screens may appear slightly different from those pictured on these pages.

Figure 5 - 5

Boot Menu

Boot Menu 5 - 13

BIOS Utilities

F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit

Item Specific Help

Exit System Setup and save your changes to CMOS.

Exit Saving Changes

Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes

Main Advanced Security Boot

Exit

Phoenix TrustedCore(tm) Setup Utility

Exit Menu

Figure 5 - 6

Exit Menu

Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Set- up defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.

5 - 14 Exit Menu

Upgrading The Computer

Chapter 6: Upgrading The Computer

Overview

This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:

• A small crosshead or Phillips screwdriver

• A small regular slotted (flathead) screwdriver

• An antistatic wrist strap Before working with the internal components you will need to wear an antistatic

wrist strap to ground yourself because static electricity may damage the components.

The chapter includes:

• Removing the Battery

• Upgrading the HDD

• Upgrading the System Memory (RAM)



Warranty Warning

Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.

Please make sure that you review each procedure before you perform it.

Overview 6 - 1

Upgrading The Computer

When Not to Upgrade



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnect-

ed all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.

These procedures involve opening the system’s case, adding and sometimes replacing parts.

You should not perform any of these upgrades if:

• Your system is still under warranty or a service contract

• You don’t have all the necessary equipment

• You’re not in the correct environment

• You doubt your abilities

Under any of these conditions, contact your service representative to purchase or replace the component(s).



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.

6 - 2 Overview

Upgrading The Computer

Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery.

1. Turn the computer off, and turn it over.

2. Slide the latches in the direction of the arrows to unlock the battery.

3. Slide the battery out in the direction of the arrow .

1 1



Warranty Warning

Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.

Figure 6 - 1

Battery Removal

Removing the Battery 6 - 3

Upgrading The Computer

Upgrading the HDD



HDD System

Warning

New HDDs are blank. Before you begin make sure: You have backed up any data you want to keep from your old drive.

You have all the CDs/DVDs required to install your operating system and programs. If you have access to the internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.

Figure 6 - 2

Keyboard Release

The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) HDDs with a height of 9.5mm (h) and a speed of 5400 RPM or lower. Follow your operating system’s installation instructions, and install all necessary drivers and utilities (see “Driver Installation” on page 4 - 2), when setting up a new hard disk.

The procedure for hard disk removal differs from Model A to Model B computers:

• See “Hard Disk Removal - Model A Computers” on page 6 - 5.

• See “Hard Disk Removal - Model B Computers” on page 6 - 8.

6 - 4 Upgrading the HDD

Upgrading The Computer

Hard Disk Removal - Model A Computers

1. Turn off the computer, and remove the battery.

2. Carefully press in the three keyboard latches ( - ) at the top of the keyboard to elevate the keyboard from its normal position (you will need to use a small screwdriver to do this).

3. Carefully lift the keyboard up (do not bend the keyboard ribbon cable ).

1 3

321



Hard Disk Drive

Speeds

If you are going to upgrade/replace the hard disk drive, note that It is recommended that HDDs of a maximum

speed of 5400 RPM are used. DO NOT use 7200rpm or higher HDDs.

Figure 6 - 3

Keyboard Release

(Model A

Computers)

Upgrading the HDD 6 - 5

Upgrading The Computer

Figure 6 - 4

HDD Bay Cover

Removal (Model A

Computers)

4. Remove screw and then use a screwdriver to push out the hard disk bay cover

7 8

at the point indicated in Figure 6 - 4.

Push the cover out here

5. Use a screwdriver to push the hard disk out of the bay at point (Figure 6 - 5).

Figure 6 - 5

HDD Removal

(Model A

Computers)

6 - 6 Upgrading the HDD

Upgrading The Computer

6. Carefully insert the hard disk into the bay until it is firmly connected (orientate the hard disk as illustrated in Figure 6 - 6

7. Insert the cover as illustrated in Figure 6 - 7 and secure the cover with the screw at point .

; don’t force it as it only fits one way).

Figure 6 - 6

HDD Insertion

(Model A

Computers)

Re-Inserting the Keyboard

When re-inserting the keyboard firstly align the three keyboard tabs at the bottom of the keyboard with the slots in the case.

8. Secure the keyboard, replace the battery and restart the computer to allow the system to detect the hard disk drive.



Figure 6 - 7

HDD Bay Cover

Insertion (Model A

Computers)

Upgrading the HDD 6 - 7

Upgrading The Computer

Hard Disk Removal - Model B Computers



Hard Disk Drive

Speeds

If you are going to upgrade/replace the hard disk drive, note that It is recommended that HDDs of a maximum

speed of 5400 RPM are used. DO NOT use 7200rpm or higher HDDs.

1. Turn off the computer, and remove the battery.

2. Locate the hard disk bay cover and remove screw .

3. Slide the hard disk assembly in the direction of the arrow .

4. Carefully lift the hard disk assembly up out of the bay.

Figure 6 - 8

Hard Disk Assembly

Removal (Model B

Computers)

6 - 8 Upgrading the HDD

Upgrading The Computer

5. Remove screws - from the hard disk assembly.

6. Separate the hard disk from the case.

7. Insert the new hard disk into the case and pay careful attention to the disk’s orientation in the case.

8. Secure the disk with the four screws and then reinsert the hard disk assembly into the computer’s hard disk bay.

9. Replace the hard disk bay screw (see Figure 6 - 8 on page 6 - 8).

545

Figure 6 - 9

HDD Removal

(Model B

Computers)

Upgrading the HDD 6 - 9

Upgrading The Computer

Upgrading the System Memory (RAM)

The computer has one memory socket for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types).

The total memory size is automatically detected by the POST routine once you turn on your computer.

1. Turn off the computer, and remove the battery.

2. Carefully press in the three keyboard latches ( - ) at the top of the keyboard to elevate the keyboard from its normal position (you will need to use a small screwdriver to do this).

3. Carefully lift the keyboard up (do not bend the keyboard ribbon cable ).

1 3

Figure 6 - 10

Keyboard Release

6 - 10 Upgrading the System Memory (RAM)

321

4. Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( &

6 7

) in Figure 6 - 11.

Upgrading The Computer

Figure 6 - 11

RAM Module

Release Latches

5. The RAM module will pop-up, and you can remove it.

Upgrading the System Memory (RAM) 6 - 11



Contact Warning

Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.

Figure 6 - 12

RAM Module

Removal

Upgrading The Computer

6. Insert a new module holding it at about a 30° angle and fit the connectors firmly



Re-Inserting the

Keyboard

When re-inserting the keyboard firstly align the three keyboard tabs at the bottom of the keyboard with the slots in

the case.

into the memory slot.

7. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure.

8. Press the module in and down towards the mai nboard until the slot levers click into place to secure the module.

9. Secure the keyboard, replace the battery and restart the computer to allow the system to detect the hard disk drive.

10. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.

6 - 12 Upgrading the System Memory (RAM)

Upgrading The Computer

Upgrading the Processor

If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.



Warranty

The CPU is not a user serviceable part. Accessing the CPU in any way, may violate your warranty.

Unauthorized tampering with the HDD may also violate your warranty.

Upgrading the Processor 6 - 13

Upgrading The Computer

6-14

Modules & Options

Chapter 7: Modules & Options

Overview

This chapter contains information on the following modules, which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative.

• Bluetooth Module

• PC Camera Module

• Wireless LAN Module

• 3.75G/HSPA Module



Driver Installation & Module Power

Make sure any modules (e.g. PC Camera, WLAN or 3.75G/HSPA modules are ON before installing the appropriate driver).



Important Notice -

3.75G/HSPA & Bluetooth/Wireless LAN

Modules

In order to comply with FCC regulations you should NOT operate the

3.75G/HSPA module

and the Bluetooth/Wireless LAN modules at the same time as this may disrupt radio frequency, and cause interference.

When the 3.75G/HSPA module is powered on, make sure that the Bluetooth/Wireless LAN modules are powered off.

Overview 7 - 1

Modules & Options



Wireless Device

Operation Aboard

Aircraft

The use of any portable electronic transmission devices aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using the computer

aboard aircraft. Use the Fn + F12 key

combination to toggle power to the Bluetooth module, and check the LED indicator to see if the module is powered on or not (see Table 1 -

2, on page 1 - 9/ Table 1 - 3, on page 1 -

11).

Bluetooth Module

The operating system’s Bluetooth Devices control panel is used to configure the Bluetooth settings in Windows XP, and therefore does not require a driver. Use the Fn + F12 key combination (see “Function/Hot Key Indicators” on page 1 - 9) to toggle power to the Bluetooth module.



Bluetooth Data Transfer

Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore if you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process from the computer has been completed.

Bluetooth Module & Resuming From Sleep Mode

The Bluetooth module’s default state will be off after resuming from the Sleep power-saving state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.

7 - 2 Bluetooth Module

Clevo M810L, M811L User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Chapter 1: Quick Start Guide

Overview

Advanced Users

Beginners and Not-So-Advanced Users

Warning Boxes

Not Included

Model Differences

System Software

System Startup

System Map: LCD Panel Open - Model A

System Map: LCD Panel Open - Model B

Keyboard

Function/Hot Key Indicators

System Map: Front & Rear Views

System Map: Left & Right Views

System Map: Bottom View

3.75G/HSPA Module USIM Card Installation

Windows XP Start Menu & Control Panel

Video Features

Dynamic Video Memory Technology

Display & Graphics Properties

Power Management Features

Chapter 2: Features & Components

Overview

Hard Disk Drive

External USB Optical (CD/DVD) Device

Loading Discs

Handling CDs or DVDs

DVD Regional Codes

7-in-1 Card Reader

TouchPad and Buttons/Mouse

Audio Features

Audio Recording from Microphone

Parallel Printer

Adding a Printer

USB Printer

Chapter 3: Power Management

Overview

Advanced Configuration and Power Interface

The Power Sources

AC/DC Adapter

Battery

Turning on the Computer

Power Schemes

System Power Options

Hibernate Mode vs. Shutdown

Stand by Mode vs. Hibernate Mode

Stand by

Hibernate

Configuring the Power Button

Battery Information

New Battery

Battery Life

Recharging the Battery with the AC/DC Adapter

Proper handling of the Battery Pack

Battery FAQ

Chapter 4: Drivers & Utilities

What to Install

Module Driver Installation

Driver Installation

Authorized Driver Message

New Hardware Found

Version Conflict Message

Updating/Reinstalling Individual Drivers

Driver Installation Procedure

Chipset

Video

Audio

TouchPad

Card Reader

Hot Key

Optional Drivers

Bluetooth Module

PC Camera Module

Wireless LAN Module