Intel and Atom are trademarks/registered trademarks of Intel Corporation.
I
Preface
FCC Statement
(Federal Communications Commission)
You are cautioned that changes or modifications not expressly approved by the party responsible for comp liance
could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Re orient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the service representative or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1.This device may not cause interference.
And
2.This device must accept any interference, including interference that may cause undesired operation of the
device.
II
Preface
FCC RF Radiation Exposure Statement:
1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator
and your body.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
III
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1.Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet
basement or near a swimming pool.
2.Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3.Do not use the telephone to report a gas leak in the vicinity of the leak.
4.Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5.This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 -
240V, 50 - 60Hz, DC Output 19V, 3.42A OR 18.5V, 3.5A).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
IV
This Computer’s Optical Device is a Laser Class 1 Product
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1.Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2.Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
V
Preface
3.Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4.Follow the proper workin g procedu res for t he comput er. Shut the computer down properly and don’t for ge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5.Take care when using peripheral devices.
Use only approved brands of
peripherals.
VI
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
Power Safety
The computer has specific power requirements:
Preface
•Only use a power adapter approved for use with this computer.
•Your AC/DC adapter may be designed for international travel but it still requires a
steady , uninterru pted power suppl y. If you are unsure of your local power specifications,
consult your service representative or local power company.
•The power adapter may have either a 2-prong or a 3-prong grounded plug. The third
prong is an important safety feature; do not defeat its purpose. If you do not have access
to a compatible outlet, have a qualified electrician install one.
•When you want to unplug the power cord, be sure to disconnect it by the plug head, not
by its wire.
•Make sure the socket and any extension cord(s) you use can support the total current
load of all the connected devices.
•Before cleaning the computer, make sure it is disconnected from any external power
supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VII
Preface
Battery Precautions
•Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
•Do not remove any batteries from the computer while it is powered on.
•Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
•Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
•Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qual-
ified service personnel.
•Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
•Keep the battery away from metal appliances.
•Affix tape to the battery contacts before disposing of the battery.
•Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
VIII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
•When the power cord or AC/DC adapter is damaged or frayed.
•If the computer has been exposed to rain or other liquids.
•If the computer does not work normally when you follow the operating instructions.
•If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
•If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before turning the computer on.
IX
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1.Check that the battery pack and any spares are fully charged.
2.Power off the computer and peripherals.
3.Close the display panel and make sure it’s latched.
4.Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5.The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6.Put the notebook in its carrying bag and secure it with the bag’s straps.
7.If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8.Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hard -
ware and software. Make sure your documents are prepared.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the vent(s)/fan intake(s)/outlet(s) to be blocked. To prev ent your
computer from overheating make sure nothing blocks the vent(s)/fan intake(s)/outlet(s) while the computer is in use.
X
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
XI
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
•Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
•Your knees should be slightly higher than your hips. Place you r fe et fl at on the floor or on a
footrest if necessary.
•Use a chair with a back and adjust it to support your lower back comfortably.
•Sit straight so that your knees, hips and elbows form approximately 90-degree angles when
you are working.
•Take periodic breaks if you are using the computer for long periods of time.
Remember to:
•Alter your posture frequently.
•Stretch and exercise your body several times a day.
•Take periodic breaks when you work at the computer for long periods of time. Frequent and
short breaks are better than fewer and longer breaks.
XII
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
•Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
•Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
•Position the display directly in front of you at a comfortable viewing distance.
•Adjust the display-viewing angle to find the best position.
LCD Screen Care
To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for
an extended period of time) take the following precautions:
•Set the Windows Power Plans to turn the screen off after a few minutes of screen idl e time.
•Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).
•Rotate desktop background images every few days.
•Turn the monitor off when the system is not in use.
XIII
Preface
XIV
Contents
Notice ................................................................................. I
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
• Chapter 4The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Bluetooth, PC Camera, and Wireless LAN modules (some of
which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the Intel Videodriver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the reminder of the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
Notes
Check the light colored
boxes with the mark
above to find detailed information about the computer’s features.
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 2 Overview
Quick Start Guide
Not Included
Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed. You will be unable to use most advanced controls until the necessary drivers and utilities are prope rly installed. If
your system hasn’t been properly configured (your service representative may have already done that for you); refer to
Chapter 4 for installation instructions.
Ports and Jacks
See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1
Overview 1 - 3
1
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find the following operating systems are supported.
Operating System & VersionNote
In order to run Windows XP without limitations or
*Windows XP (Home or Professional) with Service Pack 3
Table 1 - 1 - Operating Systems Supported
decreased performance, your computer requires a
minimum 512MB of system memory (RAM)
Windows Vista Service Pack 3
Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3) before
installing any drivers. Go to the Microsoft website for download details, or contact your service center.
1 - 4 Overview
Quick Start Guide
Inserting the AC/DC Adapter Cable
Take care when connecting the AC/DC adapter cable into the DC-In jack on the computer. The combination of
some case designs and AC/DC adapters will expose part of the end of the adapter cable when connected to the
DC-In jack (see Figure 1 - 1); this is a normal situation.
DO NOT insert the adapter cable into the DC-In jack any further than necessary (i.e. until you meet resistance),
otherwise you may cause damage to the computer. The LED indicator will be orange when the adapter is
connected.
1
Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In
Inserting the AC/DC Adapter Cable 1 - 5
1
Quick Start Guide
System Startup
1.Remove all packing materials, and place the computer on a stable surface.
2.Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
3.Attach the AC/DC adapter to the DC-In jack on the left of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
4.Use one hand to carefully raise the lid/LCD to a comfortable viewing angle, while using the other hand (as illustrated
in
Figure 1 - 2
5.Press the power button to turn the computer “on”.
Note that you should always shut your computer down by choosing the Turn Off Computer command from the Start
menu in Windows. This will help prevent hard disk or system problems.
below) to support the base of the computer (
Note: Never
Shutdown
lift the computer by the lid/LCD).
Figure 1 - 2 - Opening the Lid/LCD/Computer with AC/DC Adapter Plugged-In
1 - 6 System Startup
Quick Start Guide
1
System Map: LCD Panel Open
1
3
9
2
6
3
4
5
7
8
10
Wireless Device
Operation Aboard
Aircraft
The use of any portable electronic transmission devices
aboard aircraft is usually prohibited. Make sure the module(s) are OFF if you are using
the computer aboard aircraft.
Use the key combinations to
toggle power to the WLAN/Bluetooth modules, and
check the LED indicator icon
to see if the modules are powered on or not (see Table 1 -
5, on page 1 - 11/ Table 1 - 3,
on page 1 - 8).
Figure 1 - 3
LCD Panel Open
1.Built-In PC Camera
(
Optional
2.LCD
3.Speakers
4.Power Button
5.Hot Key Buttons
6.LED Status
Indicators
7.Keyboard
8.Touchpa d &
Buttons
9.LED Power &
Communication
Indicators
10. Built-In Microphone
)
System Map: LCD Panel Open 1 - 7
1
Quick Start Guide
LED Indicators
The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators)
on the computer display helpful information about the
current status of the computer.
IconColorDescription
GreenSilent Mode Activated (see over)
OffNormal Mode Activated (see over)
GreenHard Disk Activity
GreenNumber Lock Activated
GreenCaps Lock Activated
Green
Table 1 - 2 - LED Status Indicators
Scroll Lock Activated (to activate
press Fn & Scr Lk)
IconColorDescription
OrangeDC Power is Plugged In
GreenThe Computer is On
Blinking Green
OrangeThe Battery is Charging
GreenThe Battery is Fully Charged
Blinking Orange
Green
Orange
The Computer is in Sleep
Mode
The Battery Has Reached
Critically Low Power Status
The (optional) Wireless LAN
Module is Powered On
The (optional) Bluetooth
Module is Powered On
Table 1 - 3 - LED Power & Communication Indicators
Note that the LED indicator does not have any function in this computer model series as there is no 3G module
available as an option for this model.
1 - 8 System Map: LCD Panel Open
Quick Start Guide
1
Hot Key Buttons & Keyboard
These buttons give instant access to the default Internet browser and e-mail program, and allow you to toggle the Silent Mode on/off with one quick button
press.
Hot KeyFunction
Activate the Default E-Mail Browser
Activate the Default Internet Program
Toggle *Silent Mode (for power saving)
Table 1 - 4 - Hot Key Buttons
*When enabled, Silent Mode will reduce fan noise
and save power consumption. Note this may reduce
computer performance.
The keyboard has a numerical keypad for easy numeric data input, and features function keys (see Table 1 -
5, on page 1 - 11) to allow you to change operational
features instantly.
Activate the Number Lock feature by pressing the
Num Lk key at the top right of the keyboard. You may
check if Number Lock is enabled or not by looking at
the LED status indicators.
Other Keyboards
If your keyboard is damaged or you just want to make
a change, you can use any standard USB keyboard.
The system will detect and enable it automatically.
However special functions/AP-Key buttons unique to
the system’s regular keyboard may not work.
NumLk & ScrLk
Hold down the Fn Key and either NumLk or ScrLk to
enable number or scroll lock, and check the LED indicator for status.
Hot Key Buttons & Keyboard 1 - 9
1
Quick Start Guide
Function Keys
Play/Pause Key
Numerical Keypad
Fn Key
Figure 1 - 4 - Keyboard
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special
characters. These special characters can only be produced by using the numeric keypad.
Regular number keys (in the upper row of the keyboard) will not work. Make sure that Num-
Lk is on.
NumLk &
ScrLk Keys
1 - 10 Hot Key Buttons & Keyboard
Quick Start Guide
Function/Hot Key Indicators
The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition
to the basic function key combinations; visual indicators are available when the hot key utility provided is installed. When the driver is installed, an icon will appear in the taskbar.
KeysFunctionKeysFunction
Fn + ~Play/Pause (in Audio/Video Programs)Fn + F7Display Toggle
1
Fn + F1
Fn + F2
Fn + F3
Fn + F4Sleep ToggleFn + F12
Fn + F5/F6
TouchPad Toggle
(Press a key to or use TouchPad to turn on)
*When enabled, Silent Mode will reduce fan noise and save power consumption. Note this may reduce computer performance.
Turn LCD Backlight Off
Mute Toggle
Volume Decrease/Increase *Silent Mode Toggle
Fn + F8/F9
Fn + F10
Fn + F11
Table 1 - 5 - Function & Hot Key Indicators
Brightness Decrease/Increase
PC Camera Power Toggle
WLAN Module Power Toggle
Bluetooth Module Power Toggle
Function/Hot Key Indicators 1 - 11
1
Quick Start Guide
Figure 1 - 5
Front & Rear Views
1.LED Power & Communication Indicators
2.7-in-1 Card Reader
3.Microphone-In Jack
4.Headphone-Out
Jack
5.Battery
System Map: Front & Rear Views
1
2
7-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) /
Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
43
5
1 - 12 System Map: Front & Rear Views
Quick Start Guide
1
System Map: Left & Right Views
2
1
To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s) while the computer is in use.
3
6
4
5
5
7
Overheating
Figure 1 - 6
Left & Right Views
1.DC-In Jack
2.RJ-45 LAN Jack
3.External Monitor
Port
4.Vent/Fan Intake/
Outlet
5.2 * USB 2.0 Ports
8
6.Optical Device
Drive Bay
7.RJ-11 Phone Jack
8.Security Lock Slot
System Map: Left & Right Views 1 - 13
1
Quick Start Guide
Disk Eject Warning
Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop
the disk first then eject it, or press the stop button
twice.
CD/DVD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to
an unexpected power interruption) you may push the
end of a straightened paper clip into the emergency
eject hole. Do not use a sharpened pencil or any object that may break and become lodged in the hole.
Don’t try to remove a floppy disk/CD/DVD while the
system is accessing it. This may cause the system to
“crash”.
Changing DVD Regional Codes
Go to the Control Panel and double-click Device
Manager (Hardware and Sound), then click th e +
next to DVD/CD-ROM drives. Double-click on the
DVD-ROM device to bring up the Properties dialog
box, and select the DVD Region (tab) to bring up the
control panel to allow you to adjust the regional code.
DVD region detection is device dependent, not OSdependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
cannot be altered even if you change your operating
system or you use the module in another computer.
1 - 14 System Map: Left & Right Views
Quick Start Guide
1
System Map: Bottom View
Overheating
To prevent your computer from
overheating make sure nothing
blocks the Vent/Fan Intake while
the computer is in use.
CPU
The CPU is not a user serviceable
part. Opening this compartment, or
accessing the CPU in any way, may
violate your warranty.
2
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely
discharge and charge the battery at least once every 3 0 days or after ab out 20 partial discharges.
1
3
Figure 1 - 7
Bottom View
1.Battery (8 Cell
Battery Pictured)
2.Hard Disk Bay
Cover
3.RAM & CPU Bay
Cover
System Map: Bottom View 1 - 15
1
Quick Start Guide
Windows XP Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can cu stomize the look of
the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Click here to toggle Category View
Figure 1 - 8 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessedfrom the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic controls for many of the features, however many new controls are added (or existing ones are enhanced) when you install the drivers. To see
all controls it may be necessary to toggle off Category View.
1 - 16 Windows XP Start Menu & Control Panel
Quick Start Guide
Video Features
You can switch display devices, and configure display options, from the Display Properties control panel in
Windows as long as the appropriate video driver is installed.
To access Display Properties in Windows:
1.Click Start, point to Settings and click Control Panel (or just click Control Panel).
2.Double-click Display (icon) - In the Appearances and Themes category.
3.Click Settings (tab) in the Display Properties dialog box.
4.Move the slider to the preferred setting in Screen resolution (Figure 1 - 9 on page 1 - 18).
5.Click the arrow, and scroll to the preferred setting in Color quality (Figure 1 - 9 on page 1 - 18).
6.You can also access Display Properties by right-clicking the desktop and scrolling down and clicking
Properties. Click Settings (tab) and adjust as above.
7.Open the Display Properties control panel, and click Advanced (button) (Figure 1 - 9 on page 1 - 18) to
bring up the Advanced properties tabs.
8.Click the Intel(R) Graphic s Media Ac ce le rat or Dr iv er for Mobile tab, and click Graphics Properties (button)
to make any video adjustments you require.
9.You can also access Graphics Properties from the Windows Intel(R) GMA Driver for Mobile control p anel, or
from the taskbar icon .
Dynamic Video Memory Technology
Intel® DVMT automatically and dynamically allocates as much (up to 128MB) system memory (RAM) as needed to the video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the operating system.
1
2
3
1
Video Features 1 - 17
1
Quick Start Guide
Display & Graphics Properties
Taskbar Icon
You can also access the controller properties from the taskbar. Click on the icon to bring
up the menu and scroll to
Graphics Properties.
If you cannot see the tray icon
go to the Intel(R) Graphics
Media Accelerator Driver for
Mobile tab and click the
“Show Tray Icon” tickbox. Alternatively right-click the desktop and select Graphics
Options > Tray Icon > Enable.
1 - 18 Video Features
1
2
3
Figure 1 - 9 - Display & Graphics Properties
Quick Start Guide
Power Management Features
The Power Options control panel icon in Windows allows you to configure power management features for
your computer. You may conserve power through individual components such as the monitor or hard disk (by
means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout
the system (enable Hibernate support from the control panel as pictured in Figure 1 - 10).
Figure 1 - 10 - Power Options
The computer’s power button, sleep button (Fn + F4 key combination), and lid (closing the lid) may be set to
send the computer in to either Standby or Hibernate mode.
1
Power Saving and Performance
Power Schemes may have an affect on your computer performance.
Power Management Features 1 - 19
1
Quick Start Guide
1 - 20
Features & Components
Chapter 2: Features & Components
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive
•Optical (CD/DVD) Device
•7-in-1 Card Reader
•TouchPad and Buttons/Mouse
•Audio Features
•Adding a Printer
2
Overview 2 - 1
Features & Components
2
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Power Safety
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" serial (SATA) hard disk drives (see “Storage”
on page C - 2) with a height of 9.5 mm.
The hard disk is accessible from the bottom of your computer as seen below.For further details see “Upgrading the Hard Disk Drive” on page 6 - 4.
Figure 2 - 1
Hard Disk Location
2 - 2 Hard Disk Drive
Features & Components
Optical (CD/DVD) Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 2). The
optical device is usually labeled “Drive D:” and may be used as a boot device if
properly set in the BIOS (see “Boot Menu” on page 5 - 12).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole
3
to open the tray.
1
2
1
2
3
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-dows. Click the Volume
icon on the taskbar to
check the setting (see
“Audio Features” on
page 2 - 8).
Figure 2 - 2
Optical Device
2
Optical (CD/DVD) Device 2 - 3
Features & Components
2
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
•Hold the CD or DVD by the edges; do not touch the surface of the disc.
•Use a clean, soft, dry cloth to remove dust or fingerprints.
•Do not write on the surface with a pen.
•Do not attach paper or other materials to the surface of the disc.
•Do not store or place the CD or DVD in high-temperature areas.
•Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
•Do not bend the CD or DVD.
•Do not drop or subject the CD or DVD to shock.
Handling CDs or DVDs
2 - 4 Optical (CD/DVD) Device
Features & Components
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 14.
.
DVD Regional Coding
RegionGeographical Location
1USA, Canada
2
3
4
5
6China
Western Europe, Japan, South
Africa, Middle East & Egypt
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
South & Central America, Mexico,
Australia, New Zealand
N Korea, Russia, Eastern Europe,
India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Optical (CD/DVD) Device 2 - 5
Features & Components
2
Card Reader Cover
Make sure you keep the
rubber cover provided in
the card reader when
not in use. This will help
prevent foreign objects
and/or dust getting in to
the card reader.
7-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “CardReader” on page 4 - 6).
•MMC (MultiMedia Card)
•SD (Secure Digital)
•MS (Memory Stick)
•MS Pro (Memory Stick Pro)
•MS Duo (requires PC adapter*)
•Mini SD (requires PC adapter*)
•RS MMC (requires PC adapter*)
*Note: The PC adapters are usually supplied with these cards.
Figure 2 - 3
Right View
1.Card Reader
1
2 - 6 7-in-1 Card Reader
Features & Components
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.
Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 6) you
can configure the functions by double-clicking the TouchPad driver icon on the
taskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointer
motion and sensitivity options to your preferences. You will find further information
at www.synaptics.com.
Mouse Driver
If you are using an external mouse your operating system may be
able to auto-configure
your mouse during its
installation or only enable its basic functions.
Be sure to check the
device’s user documentation for details.
Figure 2 - 4
Mouse Properties
2
TouchPad and Buttons/Mouse 2 - 7
Features & Components
2
Audio Features
You can configure the audio options on your computer from the Sounds and Audio
Sound Volume
Adjustment
How high the sound
volume can be set depends on the setting of
the volume control
within Windows (and
the volume control
function keys on the
computer). Click the
Volume icon on the
taskbar to check the
setting.
Devices Windows control panel, or from the Realtek HD Audio Manager
icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration
menus). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Figure 2 - 5
Realtek HD Audio
Manager
2 - 8 Audio Features
Features & Components
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most current printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1.Set up the printer according to its instruction s (unpacking, p aper tr ay, toner/ink cartridge etc.).
2.Turn ON the computer.
3.Turn ON the printer.
4.Connect the printer’s USB cable to one of the USB ports on the computer.
5.Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar,
however you will need to purchase a parallel to USB converter.
Parallel Printer
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
2
Adding a Printer 2 - 9
Features & Components
2
2-10
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system. This chapter covers:
•The Power Sources
•Turning on the Computer
•Power Schemes
•System Power Options
•Configuring the Power Button
•Battery Information
Advanced Configuration and Power Interface
The ACPI interface provides the computer with enhanced power saving techniques
and gives the operating system (OS) direct control over the power and thermal states
of devices and processors. For example, it enables the OS to set devices into lowpower states based on user settings and information from applications. ACPI is fully
supported in Windows XP.
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
(Note: All pictures used
on the following pages
are from the WindowsXP OS.)
3
Overview 3 - 1
Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components.
1.Attach th e AC/DC adapter to the DC-in jack on the left of the computer.
2.Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.
3.Raise the lid/LCD to a comfortable viewing angle.
4.Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery dischargecompletely before recharging (see “How do I completely discharge the battery?”
on page 3 - 12).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 9.
3 - 2 The Power Sources
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
Power Button as Stand by or Hibernate Button
If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the OS’s
“Power Options” control panel to set the power button to send the system into Stand by or
Hibernate mode (see your OS’s documentation, or “Configuring the Po wer Button” on
page 3 - 8 for details).
Power Management
Shutdown
Note that you should always shut your computer down by choosing the
Turn Off Computer
command from the Start
menu in Windows. This
will help prevent hard
disk or system problems.
3
Turning on the Computer 3 - 3
Power Management
Power Schemes
3
Resuming
Operation
Press a key on the keyboard, or move the
mouse/TouchPad to resume from Monitor or
Hard Disk Stand by.
Figure 3 - 1
Power Schemes
You can set your computer to conserve power through individual components by
means of Power Schemes. You can also adjust the settings for each scheme to set
the monitor to turn off after a specified time, and the computer's hard disk motor to
turn off if the hard disk drive has not been accessed for a specified period of time (if
the system reads or writes data, the hard disk motor will be turned back on). The
schemes may also be set to set a specified time for the system to enter Stand by or
Hibernate modes (see “System Power Options” on page 3 - 6).
3-4Power Schemes
Each WindowsPower Scheme will also adjust the processor performance of your
machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose the Home/Office Desk scheme for maximum performance when the com-
puter is powered from an AC power source. Choose the Max Battery scheme (bear
in mind that this scheme may slow down the overall performance of the computer in
order to save power) for maximum power saving when the computer is battery (DC
power) powered. Windows will use Portable/Laptop as the default scheme.
Power Management
3
Power Schemes 3 - 5
Power Management
System Power Options
3
Stand by/Hibernate
or Shutdown Error
The computer may stop
responding when you
put it into (or resume
from) Stand By or Hibernate, or when you shut
down.
You can use the system power options to stop the computer’s operation and restart
where you left off. This system features Stand by and Hibernate sleep mode levels
(Hibernate mode will need to be enabled by clicking the option in the Hibernate
tab in the Power Options control panel - see Figure 3 - 2 on page 3 - 7).
Hibernate Mode vs. Shutdown
Hibernate mode and Shutdown are the same in that the system is off and you need
to press the power button to turn it on. Their main difference is:
This error is caused by
power management
within Windows XP,
when applied to a PCCamera attached to the
internal USB hub.
Microsoft has posted a
Hotfix for this error on its
website (search for Hotfix KB909667).
Download and install the
Hotfix to correct this error.
When you come back from hibernation, you can return to where you last left off
(what was on your desktop) without reopening the application(s) and file(s) you last
used.
You can use either method depending on your needs.
Stand by Mode vs. Hibernate Mode
If you want to stay away from your work for just a while, you can put the system on
Stand by instead of in hibernation. It takes a longer time to wake up the system from
Hibernate mode than from Stand by mode.
3 - 6 System Power Options
Stand by
Stand by saves the least amount of power, but takes the shortest time to return to full
operation. During Stand by the hard disk is turned off, and the CPU is made to idle
at its slowest speed. All open applications are retained in memory. When you are not
using your computer for a certain length of time, which you specify in the operating
system, it will enter Stand by mode to save power.
Hibernate
Hibernate uses no power and saves all of your information on a part of the HDD before it turns the system off. Although it saves the most power it takes the longest time
to return to full operation. You can set your computer to automatically enter Hibernate mode when the battery power is almost depleted. You will need to enable Hibernate mode from the Hibernate tab in the Power Options control panel. Thesystem will resume from Hibernate mode by pressing the power button.
Power Management
System Resume
The system can resume
from Stand by mode by:
• Pressing the power
button
• Pressing the Sleep/Resume key combination
• An incoming call
received on the
modem (if enabled)
• Network card (Wake
On LAN) activity (if
enabled)
3
Figure 3 - 2
Enable Hibernation
System Power Options 3 - 7
Power Management
Configuring the Power Button
3
Sleep Button
You may also configure
the Sleep/Resume key
combination (Fn + F4)
from the menu illustrated. In Windows this is
referred to as the Sleep
button.
Figure 3 - 3
Power Options
(Advanced - Power
Buttons)
The power button may be set to send the computer in to either Stand by or Hibernate mode. In Stand by mode, the LED will blink green. In Hibernate mode
the LED will be off (battery) or orange (AC/DC adapter). If you are in a power saving mode set to save power through individual components (e.g. har d disk, monitor),
the LED will remain green.
Power ButtonSleep/ResumeLid
(Sleep) Button
3 - 8 Configuring the Power Button
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 12 for instructions on how to do this).
Battery Life
Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached. Power Options (you may
set low battery Alarms and actions, and check the Power Meter from the PowerOptions control panel), and settings in the OS will help prolong the battery life if
configured appropriately.
Power Management
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 4
Power Options
(Alarm & Power
Meter)
3
Battery Information 3 - 9
Power Management
Battery life may be shortened through improper maintenance. To optimize the life
3
Conserving Battery
Power
To conserve battery power:
Lower the brightness level
of the LCD display. The
system will decrease LCD
brightness slightly to save
power when it is not powered by the AC/DC adapter.
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you need to remove
the battery for any reason, see “Removing the Battery” on page 6 - 3.
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
Close modem or communication applications when
they are not being used.
Remove any unused PC
Cards from the computer
(PC Cards quickly use up
battery power even if the
system enters sleep
mode).
Disconnect any unnecessary external devices.
tors” on page 1 - 8 for information on the battery charge status, and to “Battery Information” on page 3 - 9 for more information on how to maintain and properly
recharge the battery pack.)
3 - 10 Battery Information
Proper handling of the Battery Pack
•DO NOT disassemble the battery pack under any circumstances
•DO NOT expose the battery to fire or high temperatures, it may explode
•DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.
Power Management
3
Battery Information 3 - 11
Power Management
Battery FAQ
3
Caution
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer by yourself even when you see a message that indicates the
battery is critically low, just let the computer use up all of the battery power and shut
down on its own. Disable the Power Options functions i n the Co ntrol Panel, especially any Alarms (unclick the tickboxes - see page 3 - 9) and Schemes (change all
the settings to Never - see page 3 - 4). As the battery nears the end of its life save
and close any critical files.
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
3 - 12 Battery Information
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some
of the computer’s subsystems. The system takes advantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to
manually install some system-required drivers and
utilities.
What to Install
The Device Drivers & Utilities + User’s Manual disc
contains the drivers and utilities necessary for the
proper operation of the computer.
Table 4 - 1, on page 4 - 3 lists what you need to install
and it is very important that the drivers are in-stalled in the orderindicated.
Module Driver Installation
The procedures for installing drivers for the Wireless
LAN and PC Camera modules are provided in “Mod-
ules & Options” on page 7 - 1.
4
What to Install 4 - 1
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers/Option Drivers (button).
Follow the instructions to install the driver. Alternatively
4
click Start, navigate (Browse..) to the executable file
and then follow the manual setup instructions.
1.Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2.Click to select the driver you wish to install, after
installing each driver it will become grayed out (if
you need to reinstall any driver, click the Unlock
button).
3.Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
Figure 4 - 1 - Drivers Installer Screen 1
4 - 2 Driver Installation
Figure 4 - 2 - Drivers Installer Screen 2
Driver - Windows XP
with Service Pack 3
ChipsetPage 4 - 5
Page #
Drivers & Utilities
Manual Driver Installation
Click Browse CD (button) in the Drivers Installer ap-
plication and browse to the executable file in the appropriate driver folder.
Make sure you install Windows XP Service Pack 3 (or a Windows XP version which includes Service Pack 3) before in-
stalling any drivers.
Driver Installation 4 - 3
4
Drivers & Utilities
Authorized Driver Message
If you receive a message telling you that the driver you
are installing is not authorized (Digital Signature NotFound), just click Yes or Continue Anyway to ignore
the message and continue the installation procedure.
4
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installation procedure (other than when outlined in the driver
install procedure), click Cancel to close the window,
and follow the installation procedure as directed.
Version Conflict Message
During driver installation if you encounter any “file
version conflict” message, please click Yes to choose
to keep the existing (newer) version.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Add/Remove Programs item. If yousee the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be
necessary to restart the computer). Go to the appropriate section of the manual to complete the update/reinstall procedure for the driver in question.
If the driver is not listed in the Add/Remove Pro-grams item:
1.Click Start (menu), point to Settings and click Control Panel (or click Start > Control Panel).
2.Double-click System (icon); System (icon) is in
Performance and Maintenance (category).
3.Click Hardware (tab) > Device Manager (button).
4.Double-click the device you wish to update/reinstall
the driver for (you may need to click “+”).
5.Look for the Update Driver button (check the
Driver tab) and follow the on screen pr ompts.
4 - 4 Driver Installation
Drivers & Utilities
Driver Installation Procedure
Insert the Device Drivers & Utilities + User’s Manual
disc and click Install Drivers (button), or click OptionDrivers (button) to access the optional driver menu.
Chipset
1.Click 1.Install Chipset Driver > Yes.
2.Click Next > Yes > Next > Next.
3.Click Finish.
Video
1.Click 2.Install Video Driver > Yes.
2.Click Next > Yes > Next > Next.
3.Click Finish to restart the computer .
Audio
1.Click 3.Install Audio Driver > Yes.
2.Click Next.
3.Click Finish to restart the computer .
Modem
1.Click 4.Install Modem Driver > Yes.
2.Click OK.
3.The modem is ready for dial-up configuration.
4
Modem Country Selection
Go to the Phone andModem Options control panel
(Hardware and Sound) and make sure the modem
country selection is appropriate for you.
LAN
1.Click 5.Install LAN Driver > Yes.
2.Click Next > Install.
3.Click Finish.
4.The network settings can now be configured.
Driver Installation 4 - 5
Drivers & Utilities
TouchPad
1.Click 6.Install TouchPad Driver > Yes.
2.Click Next > Next > Next.
3.Click Finish to restart the computer.
4
CardReader
1.Click 7.Install Cardreader Driver > Yes.
2.Click Install > Finish to complete the installa-
tion.
Hot Key
1.Click 8.Install HotKey Driver > Yes.
2.Click Next > Install.
3.Click Finish > Finish to restart the computer.
Optional Drivers
See the pages indicated overleaf for the driver installation procedures for any modules included in your purchase option.
Note: The operating system is the default setting for
Bluetooth control in Windows XP, and does not require a driver. See “Bluetooth Module” on page 7 -
2 for configuration instructions.
PC Camera Module
See the introduction in “PC Camera Module” on
page 7 - 7, and check the installation procedure.
Wireless LAN Module
See the introduction in “Wireless LAN Module” on
page 7 - 13, and check the installation procedure.
Drivers & Utilities
4
Driver Installation 4 - 7
Drivers & Utilities
4
4-8
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Phoenix TrustedCore SetupUtility
If your computer has never been set up, or you are mak ing important chan ges to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your
system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what youare doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
Overview 5 - 1
BIOS Utilities
Phoenix TrustedCore(tm) NB
Copyright 1985-2006 Phoenix Technologies Ltd.
All Rights Reserved
Bios Revision: ********
KBC/EC Firmware Revision: ********
CPU=1Processors Detected
Intel(R) Atom(TM) CPU N270@ 1.60GHz
1015M System RAM Passed
512 KB L2 Cache
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 0: FUJITSU MHV2100BH PL
ATAPI CD-ROM: Optiarc CDRWDVD CRX890S
Mouse intialized
Press <F2> to enter SETUP
The Power-On Self Test (POST)
POST Screen
1.BIOS information
2.CPU type
3.Memory status
5
4.Enter Setup prompt
appears only during
POST
Note:
The
POST
screen
as pictured right is for
guideline purposes only.
POST
The
your computer may appear slightly different. If
you disable the
time Diagnostic Screen
the POST screen will not
appear.
screen on
Boot-
Figure 5 - 1
POST Screen
Each time you turn on the computer, the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.
,
1
2
3
4
5 - 2 The Power-On Self Test (POST)
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:
•Press <F1> to resume
•<F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct
configuration.
BIOS Utilities
5
Press F2 to run the Setup program and try to correct the problem. If you still get an
error message after you change the setting, or if the “cure” seems even worse, call
for help.
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
The Setup Utility
The Phoenix TrustedCore SetupUtility tells the system how to configure itself
and manage basic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The prompt
5
(Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds
after you turn on the system. If you get a “Keyboard Error”, (usually because you
pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.
5 - 4 The Setup Utility
Setup Screens
The following pages contain additional advice on portions of the Phoenix TrustedCore Setup Utility.
BIOS Utilities
Setup Menus
Along the top of the screen is a menu bar with menu headings. When you select a
heading, a new screen appears. Scroll through the features listed on each screen to
make changes to Phoenix TrustedCore SetupUtility.
Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configuration appropriate for your
model and options.
F1Help Select Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
[22:12:05]
Item Specific Help
<Tab>, <Shift Tab>, or
<Enter> selects field.
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
5-6Main Menu
SATA Port 1 (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of a HDD on the com-
puter’s Serial ATA Port 1. Use the Auto (Type:) setting to have the items configured
automatically for you.
SATA Port 2 (Main Menu)
Pressing Enter opens the sub-menu to show the configuration of an optical Device
on the computer’s Serial ATA Port 2. Use the Auto (Type:) setting to have the items
configured automatically for you.
System/Extended Memory (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
Power On Boot Beep[Disabled]
Battery Low Alarm Beep[Enabled]
Detect External CRT[Enabled]
F1HelpSelect Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Legacy USB Support (Advanced Menu)
Use this menu item to enable/disable the support for Legacy Universal Serial Bus in
non-USB aware operating systems.
Advanced
Item Specific Help
Enable support for
Legacy Universal Serial
Bus.
5 - 8 Advanced Menu
Boot-time Diagnostic Screen (Advanced Menu)
Use this menu item to enable/disable the Boot-time Diagnostic Screen or POST
screen (see “The Power-On Self Test (POST)” on page 5 - 2).
Reset Configuration Data (Advanced Menu)
This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious
system conflict that the operating system is unable to boot.
Power On Boot Beep (Advanced Menu)
Use this menu item to enable/disable the beep as the computer starts up.
Battery Low Alarm Beep(Advanced Menu)
Use this menu item to enable/disable the audible warning when the battery has
reached low power status.
Detect External CRT (Advanced Menu)
This menu allows you to Enable/Disable detection for External CRT’s (external
displays). You can disable detection to save system power.
BIOS Utilities
5
Advanced Menu 5 - 9
BIOS Utilities
t
bed
Security Menu
Security Menu
The changes you
make here affect the
access to the Setup
utility itself, and also
5
access to your machine as it boots up af-
MainAdvancedSSeeccuurriittyyBootExit
=
Supervisor Password Is:Clear
User Password Is:Clear
Set Supervisor Password[Enter]
Set User Password[
Password on boot:[
Fixed disk boot sector:[Normal]
ter you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.
F1HelpSelect Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Figure 5 - 4
Security Menu
Set Supervisor Password (Security Menu)
You can set a password for access to the Phoenix TrustedCore SetupUtility. This
will not affect access to the computer OS (only the Phoenix TrustedCore SetupUtility).
Phoenix TrustedCore(tm) Setup Utility
Security
Item Specific Help
Supervisor Password
e
]
controls access to the
setup utility.
5 - 10 Security Menu
Set User Password (Security Menu)
You can set a password for user mode access to the Phoenix SecureCore Setup
Utility. This will not affect access to the computer OS, (only the Setup utility) unlessyou choose to set a Password on Boot (see below). Many menu items in the Phoenix
SecureCore Setup Utility cannot be modified in user mode. You can only set the
user password after you have set the supervisor password.
Password on boot (Security Menu)
Specify whether or not a password should be entered to boot the computer (you may
only set a password on boot if a supervisor password is enabled). If “Enabled”is selected, only users who enter a correct password can boot the system (see the
warning in the sidebar). The default setting is “Disabled”.
Fixed disk boot sector (Security Menu)
If you choose “Write-Protect” this will protect against viruses being written to the
hard disk boot sector (this is not a substitute for installing an anti-virus program - see
“Viruses” on page 8 - 4).
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter
again to confirm the password clearance.
BIOS Utilities
Password Warning
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
5
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
Security Menu 5 - 11
BIOS Utilities
Phoenix TrustedCore(tm) Setup Utility
F1HelpSelect Item-/+Change ValuesF9 Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Item Specific Help
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
Boot priority order:
1: IDE CD: Optiarc CDRWDVD CRX890S-(S
2: IDE HDD: FUJITSU MHV2100BH PL-(S1)
3: USB KEY:
4: USB FDC:
5: IDE CDROM:
6: USB HDD:
7: PCI BEV: Realtek Boot Agent
8:
Excluded from boot order:
: USB ZIP:
MainAdvancedSecurity
Boot
Exit
Boot Menu
Figure 5 - 5
Boot Menu
5
5 - 12 Boot Menu
When you turn the computer on it will look for an operating system (e.g. Windows
Vista) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in
the order specified in the Boot priority order. Item specific help on the right is
available to help you move devices up and down the order.
Exit Menu
BIOS Utilities
MainAdvancedSecurityBoot
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1HelpSelect Item-/+Change ValuesF9Setup Defaults
EscExit Select MenuEnterSelect Sub-Menu F10 Save and Exit
Phoenix TrustedCore(tm) Setup Utility
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any
changes you have made to the Setup. You can also choose to restore the original Set-up defaults that will return the Setup to its original state, and erase any previous
changes you have made in a previous session.
Figure 5 - 6
Exit Menu
5
Exit Menu 5 - 13
BIOS Utilities
5
5-14
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:
•A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
•An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
• Removing the Battery
• Upgrading the Hard Disk Drive
• Upgrading the Optical (CD/DVD) Device
• Upgrading the System Memory (RAM)
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
Upgrading The Computer
When Not to Upgrade
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnect-
6
ed all peripherals and
cables (including telephone lines). It is advisable to also remove your
battery in order to prevent accidentally turning
the machine on.
These procedures involve opening the system’s case, adding and sometimes replacing parts.
You should not perform any of these upgrades if:
• Your system is still under warranty or a service contract
•You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or replace the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.
6 - 2 Overview
Upgrading The Computer
Removing the Battery
If you are confident in undertaking upgrade procedures yourself, for safety reasons
it is best to remove the battery.
1.Turn the computer off, and turn it over.
2.Slide the latch in the direction of the arrow.
3.Slide the latch in the direction of the arrow, and hold it in place.
4.Slide the battery out in the direction of the arrow .
1
2
3
1
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
2
Figure 6 - 1
Battery Removal
3
Removing the Battery 6 - 3
Upgrading The Computer
Upgrading the Hard Disk Drive
HDD System
Warning
New HDD’s are blank. Before you begin make sure:
You have backed up any
data you want to keep from
your old HDD.
6
You have all the CD-ROMs
and FDDs required to install your operating system
and programs.
If you have access to the internet, download the latest
application and hardware
driver updates for the operating system you plan to install. Copy these to a
removable medium.
The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard
disk drives with a height of 9.5mm (h) (see “Storage” on page C - 2). Follow your
operating system’s installation instructions, and install all necessary drivers and utilities (see “Driver Installation” on page 4 - 2), when setting up a new hard disk.
1.Turn off the computer, and turn it over and remove the battery.
2.Locate the hard disk bay cover and loosen screws & .
3.Remove the hard disk bay cover .
3
4.Grip the tab and slide the hard disk in the direction of arrow
1
1
2
4
.
3
2
Figure 6 - 2
Hard Disk Bay &
Screws
6 - 4 Upgrading the Hard Disk Drive
4
Upgrading The Computer
5.Lift the hard disk up in the direction of arrow .
6.Remove the screws & and cover .
7.Reverse the process to install a new hard disk drive.
678
5
5
8
7
Figure 6 - 3
HDD & Cover
Removal
6
6
Upgrading the Hard Disk Drive 6 - 5
Upgrading The Computer
Upgrading the Optical (CD/DVD) Device
1.Turn off the computer, and turn it over and remove the battery.
2.Locate the RAM & CPU bay cover and remove screws
3.Carefully (a fan and cable are attached to the under side of the cover) lift up the
4.Remove the screw at point , and use a screwdriver to carefully push out the
5.Reverse the process to install the new device (make sure you reconnect the cable).
bay cover.
optical device at point .
6
14
- .
5
6
Figure 6 - 4
Removing the CD/
DVD Device
6 - 6 Upgrading the Optical (CD/DVD) Device
3
1
2
5
4
6
Upgrading The Computer
Upgrading the System Memory (RAM)
The computer has one memory socket for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 1 for
details of supported module types).
The total memory size is automatically detected by the POST routine once you turn
on your computer.
1.Turn off the computer, and turn it over and remove the battery.
2.Locate the RAM & CPU bay cover and remove screws
14
- .
4
6
Figure 6 - 5
RAM & CPU
Bay Screws
21
3
Upgrading the System Memory (RAM) 6 - 7
Upgrading The Computer
3.Carefully (a fan and cable are attached to the under side of the cover) lift up the
Figure 6 - 6
CPU/RAM Bay
Cover Removed
4.Carefully disconnect the fan cable , and remove the cover .
bay cover.
56
6
6
Contact Warning
Be careful not to touch
the metal pins on the
module’s connecting
edge. Even the cleanest
hands have oils which
can attract particles, and
degrade the module’s
performance.
5.Gently pull the two release latches on the sides of the memory socket in the
direction indicated by the arrows ( &
Figure 6 - 7
RAM Module
Release Latches
6 - 8 Upgrading the System Memory (RAM)
5
5
78
) in Figure 6 - 7.
7
8
Upgrading The Computer
6.The RAM module will pop-up, and you can remove it.
9
9
7.Insert a new module holding it at about a 30° angle and fit the connectors firmly
into the memory slot.
8.The module’s pin alignment will allow it to only fit one way. Make sure the module
is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit
without much pressure.
9.Press the module in and down towards the mainboard until the slot levers click into
place to secure the module.
10. Replace the bay cover and screws (make sure you reconnect the fan cable before screwing down the bay cover - see Figure 6 - 6 on page 6 - 8).
11. Restart the computer to allow the BIOS to register the new memory configu ration
as it starts up.
Figure 6 - 8
RAM Module
Removal
6
Upgrading the System Memory (RAM) 6 - 9
Upgrading The Computer
Upgrading the Processor
Warranty
The CPU is not a user
serviceable part. Opening this compartment, or
accessing the CPU in
any way, may violate
your warranty.
6
Unauthorized tampering
with the HDD may also
violate your warranty.
If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may
damage the processor or mainboard.
6 - 10 Upgrading the Processor
Modules & Options
Chapter 7: Modules & Options
Overview
This chapter contains information on the following modules, which may come with
your computer, depending on the configuration purchased. If you are unsure please
contact your service representative.
• Bluetooth Module
• PC Camera Module
• Wireless LAN Module
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft
is usually prohibited.
Make sure the module(s) are OFF if you are
using the computer
aboard aircraft.
7
Overview 7 - 1
Modules & Options
Bluetooth Module
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission devices aboard aircraft is usually prohibited. Make sure
the module(s) are OFF if
you are using the computer
aboard aircraft.
7
Use the Fn + F12 key combination to toggle power to
the Bluetooth module, and
check the LED indicator to
see if the module is powered on or not (see Table 1
- 5, on page 1 - 11/ Table 1
- 3, on page 1 - 8).
The operating system’s Bluetooth Devices control panel is used to configure the
Bluetooth settings in Windows XP, and therefore does not require a driver. Use theFn + F12 key combination (see “Function/Hot Key Indicators” on page 1 - 11) to
toggle power to the Bluetooth module.
Bluetooth Data Transfer
Note that the transfer of data between the computer and a Bluetooth enabled device is supported in one direction only (simultaneous data transfer is not supported). Therefore
if you are copying a file from your computer to a Bluetooth enabled device, you will not be
able to copy a file from the Bluetooth enabled device to your computer until the file transfer
process from the computer has been completed.
Bluetooth Module & Resuming From Sleep Mode
The Bluetooth module’s default state will be off after resuming from the Sleep power-saving
state. Use the key combination (Fn + F12) to power on the Bluetooth module after the computer resumes from Sleep.
7 - 2 Bluetooth Module
Bluetooth Local Area Connection Icon
If you want to display the Local Area Connection icon for the Bluetooth connection
in the taskbar, set it up as follows:
1.Access the Network Connections control panel in Windows (Start > Settings >
Network Connections OR Start > Connect To > Show all Connections) or by
clicking the taskbar icon .
2.Right-click the Blue to ot h con n ec tio n ic on , and se lect Properties.
3.Click to put a tick (if none is present) in the “Show icon in the notification area when connected” box and click OK.
4.Close the control panels and the icon for the Bluetooth local area connection
will be displayed in the taskbar when connected (see sidebar and overleaf).
Modules & Options
7
Figure 7 - 1
Local Area
Connection
Bluetooth Module 7 - 3
Modules & Options
Bluetooth Taskbar
Icon
Bluetooth Configuration in Windows XP
Setup your Bluetooth Device so the Computer Can Find it
1.Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on.
2.Make the device discoverable (to do this check your device documentation).
If you cannot see the
Bluetooth icon in the taskbar, access the
tooth Devices
panel. Click
(tab), and make sure that
Show Bluetooth icon in
the notification area
7
check box has a tick inside it.
Note that you will need to
check the LED indicator
to see if the module is
powered on or not.
Figure 7 - 2
Bluetooth Devices &
Click Icon Menu
7 - 4 Bluetooth Module
Blue-
control
Options
To Turn the Bluetooth Module On
1.Press the Fn + F12 key combination to power on the Bluetooth module.
2.A Bluetooth icon will appear in the taskbar (see sidebar).
3.You can then do any of the following to access the Bluetooth Devices control
panel.
•Double-click the icon to access the Bluetooth Devices control panel.
•Click Start, and click Control Panel (or point to Settings and click Control Panel), and then click Blue-
tooth Devices (Network and Internet Connections).
•Click/Right-click the icon and choose an option from the menu.
To Add a Bluetooth Device
1.Access the Bluetooth Devices control panel.
2.Click Options (tab), and make sure that Allow Bluetooth devices to connect to this computer check box (Connections) has a tick inside it.
3.Click Devices (tab), and then click Add.
4.The Add Bluetooth Device Wizard will appear.
5.Click to select “My device is set up and ready to be found”, and then click Next.
Modules & Options
Figure 7 - 3
Add Bluetooth
Device Wizard
6.The Wizard will then search for any available Bluetooth devices within range.
7.Click to select the device you want to communicate with, and click Next.
8.Select an appropriate passkey option and click Next.
9.Click Finish.
Passkey Options
You can allow the system to choose a passkey for you. You will
then be prompted to enter the generated passkey on your Bluetooth
device.
Figure 7 - 4
Passkey Option
Bluetooth Module 7 - 5
7
Modules & Options
To Change Settings for the Bluetooth Device
Bluetooth Module &
Resuming From
Sleep Mode
1.Access the Bluetooth Devices control panel.
2.Click on the device you want to change and click Properties to:
•Change the name of the device (click General, type a new name and click OK).
•Enable/Disable a service (click Services, clear/tick the check box next to the service and click OK).
To Make your Computer Discoverable to Bluetooth Devices
The Bluetooth module’s
default state will be off after resuming from the
Sleep
power-saving
state. Use the key combination (
Fn + F12
7
er on the Bluetooth
module after the computer resumes from Sleep.
) to pow-
1.Access the Bluetooth Devices control panel.
2.Click Options, and make sure that Turn discovery on check box (Discovery)
has a tick inside it.
3.Make sure that Alert me when a new Bluetooth device wants to connect check
box (Connections) has a tick inside it, if you want to be notified when a Bluetooth
device wants to connect.
Figure 7 - 5
Bluetooth Devices
Options
7 - 6 Bluetooth Module
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.