Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
©October 2006
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home
or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
AMD
Turion™ is a trademark of Advanced Micro Devices, Inc.
is a trademark of SRS Labs, Inc.
WOW
technology is incorporated under license from SRS Labs, Inc.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the
equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 11A minimum).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER, TELE-
COMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class I Product
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place where
foreign matter or moisture may
affect the system.
Don’t use or store the computer
in a humid environment.
Do not place the computer on
any surface that will block the
vents.
IV
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until
you properly shut down all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord before
attaching peripheral devices.
Perform routine maintenance
on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VI
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a steady,
uninterrupted power supply. If you are unsure of your local power specifications, consult
your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong
is an important safety feature; do not defeat its purpose. If you do not have access to a
compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by
its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load
of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and
screw(s) before turning the computer on.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter. However,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for both hard-
ware and software. Make sure your documents are prepared.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with normal luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly below the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
XII
Contents
Notice .................................................................................I
FCC Statement .............................................................II
Instructions for Care and Operation .......................... IV
Power Safety .............................................................. VI
Battery Precautions ...................................................VII
Cleaning .................................................................. VIII
Servicing ................................................................. VIII
Travel Considerations ................................................ IX
Quick Start Guide
Overview ........................................................................1-1
Advanced Users ...........................................................1-2
Beginners and Not-So-Advanced Users ......................1-2
Warning Boxes ............................................................1-2
Not Included ................................................................1-2
System Software ..........................................................1-3
System Startup .............................................................1-4
System Map: Top View with LCD Panel Open ............1-5
LED Indicators ............................................................1-6
AP-Key Buttons ........................................................... 1-7
3D AP-Key Button ......................................................1-7
Function Keys & Numeric Keypad ............................. 1-7
System Map: Front & Rear Views .................................1-9
Preface
System Map: Left View ...............................................1-10
System Map: Right View .............................................1-11
System Map: Bottom View ..........................................1-12
Windows XP Start Menu & Control Panel ..................1-13
Video Features ............................................................. 1-14
Display Devices & Options ......................................1-14
Power Management Features ....................................... 1-16
Storage Devices, Mouse, Audio &
Printer
Overview ........................................................................2-1
Hard Disk Drive ............................................................. 2-2
Optical Device ...............................................................2-3
Loading Discs ..............................................................2-3
Handling CDs or DVDs ............................................... 2-4
DVD Regional Codes .................................................. 2-5
7-in-1 Card Reader .........................................................2-6
PC Card Slot ..................................................................2-7
Inserting and Removing PC Cards ..............................2-7
Auto Mail Checker .........................................................2-8
TouchPad and Buttons/Mouse .....................................2-10
Audio Features .............................................................2-11
Configuring the Infrared Settings for FIR ...................2-12
XIII
Preface
Adding a Printer ........................................................... 2-13
USB Printer ...............................................................2-13
Install Instructions: ................................................... 2-13
Parallel Printer ........................................................... 2-13
Power Management
Overview ........................................................................3-1
Advanced Configuration and Power Interface ............3-1
The Power Sources ........................................................3-2
AC/DC Adapter ........................................................... 3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Schemes ..............................................................3-4
System Power Options ................................................... 3-6
Hibernate Mode vs. Shutdown ....................................3-6
Stand by Mode vs. Hibernate Mode ............................ 3-6
Stand by ......................................................................3-7
Hibernate ....................................................................3-7
Configuring the Power Button .......................................3-8
Battery Information .......................................................3-9
New Battery ................................................................3-9
Battery Life ................................................................. 3-9
Recharging the Battery with the AC/DC Adapter .....3-10
Proper handling of the Battery Pack .........................3-11
Battery FAQ ..............................................................3-12
Drivers & Utilities
What to Install ................................................................4-1
Module Driver Installation ..........................................4-1
RAID Setup .................................................................4-1
Service Packs ...............................................................4-3
Authorized Driver Message .........................................4-4
Version Conflict Message ...........................................4-4
New Hardware Found .................................................. 4-4
Updating/Reinstalling Individual Drivers ...................4-4
Driver Installation ..........................................................4-5
Manual Driver Installation .........................................4-6
WinXP Driver Installation Procedure ..........................4-7
Chipset ........................................................................4-7
Video ..........................................................................4-7
Audio ..........................................................................4-7
Modem ........................................................................4-8
LAN ............................................................................4-8
AP-Key Utility ............................................................4-9
TouchPad ....................................................................4-9
PCMCIA ...................................................................4-10
AMD Processor ........................................................4-10
AutoMail Checker .................................................... 4-10
Module Drivers ..........................................................4-11
Bluetooth ..................................................................4-11
Wireless LAN ...........................................................4-11
XIV
Preface
PC Camera ................................................................4-11
RAID ........................................................................4-11
TV Tuner ..................................................................4-11
BIOS Utilities
Overview ........................................................................5-1
The Power-On Self Test (POST) ...................................5-2
Failing the POST ......................................................... 5-3
Fatal Errors ................................................................. 5-3
Non-Fatal Errors .........................................................5-3
The Setup Program ........................................................5-4
Entering Setup .............................................................5-4
Setup Screens ............................................................... 5-5
Main Menu .....................................................................5-6
System Time & Date (Main Menu) ............................... 5-6
Primary Master (Main Menu) ........................................5-7
System/Extended Memory: (Main Menu) .....................5-7
Advanced Menu .............................................................5-8
Advanced Chipset Control (Advanced Menu) ..............5-8
NV RAID Configuration (Advanced Menu > Advanced
Chipset Control) .............................................................5-9
I/O Device Configuration (Advanced Menu) .............. 5-10
Reset Configuration Data (Advanced Menu) ..............5-10
Boot Logo Screen (Advanced Menu) ..........................5-10
Power On Boot Beep (Advanced Menu) .....................5-10
Battery Low Alarm Beep: (Advanced Menu) ..............5-10
Security Menu .............................................................. 5-11
Set Supervisor Password (Security Menu) ..................5-11
Password on boot: (Security Menu) .............................5-12
Boot Menu ...................................................................5-13
Exit Menu ....................................................................5-14
Upgrading The Computer
Overview ........................................................................6-1
When Not to Upgrade ..................................................6-2
Removing the Battery ....................................................6-3
Upgrading the Hard Disk Drive(s) .................................6-4
Upgrading the System Memory (RAM) ........................6-6
Upgrading the Optical (CD/DVD) Device(s) ................6-9
Removing the Video Card(s) ....................................... 6-10
Modules
Overview ........................................................................7-1
Bluetooth Module ..........................................................7-2
Bluetooth Driver Installation ......................................7-2
802.11 b/g USB WLAN Module ................................... 7-4
802.11 b/g WLAN Driver Installation ........................7-4
PC Camera Module ........................................................7-6
PC Camera Driver Installation ...................................7-6
PC Camera Audio Setup ..............................................7-7
XV
Preface
EMAMCAP .................................................................7-9
RAID Setup .................................................................7-11
RAID Mode Setup .....................................................7-13
The MediaShield Windows Utility ........................... 7-21
Mini-PCI TV Tuner Module Options ..........................7-25
Digital TV Broadcast Signal ....................................7-26
TV Recording and Power Schemes ..........................7-26
Troubleshooting
Overview ........................................................................8-1
Basic Hints and Tips ......................................................8-2
Backup and General Maintenance ................................. 8-3
Viruses ...........................................................................8-4
Upgrading and Adding New Hardware/Software ..........8-5
Problems & Possible Solutions ...................................... 8-7
Interface (Ports & Jacks)
Overview ....................................................................... A-1
Ports and Jacks .............................................................. A-2
Built-In Microphone ..................................................... A-2
Card Reader .................................................................. A-2
Consumer Infrared Transceiver .................................... A-2
DC-In Jack .................................................................... A-2
DVI-Out Port ................................................................ A-2
Headphone-Out Jack ..................................................... A-3
Infrared (FIR) Transceiver ............................................ A-3
Line-In Jack ..................................................................A-3
Microphone-In Jack ...................................................... A-3
Mini-IEEE 1394a Ports ................................................. A-4
RJ-11 Phone Jack .......................................................... A-4
RJ-45 LAN Jack ............................................................A-4
S/PDIF-Out Jack ...........................................................A-4
Security Lock Slot ........................................................A-4
Serial Port .....................................................................A-5
S-Video-In Jack ............................................................A-5
7-Pin S-Video-Out Jack ................................................A-5
TV Antenna Jack ..........................................................A-5
USB 2.0/1.1 Ports .........................................................A-5
NVIDIA Video Driver Controls
NVIDIA Video Driver Installation ............................... B-1
3D AP-Key Button ........................................................ B-2
NVIDIA Display Properties .......................................... B-3
Additional Properties ................................................. B-4
NVIDIA nView Desktop Manager ............................ B-6
SLI Multi GPU .............................................................. B-8
Display Devices ............................................................ B-9
Attaching Other Displays ............................................ B-10
Display Modes ............................................................ B-12
XVI
To Enable Extended Desktop
(Windows Display Properties) ................................ B-13
Enabling TV Display .................................................. B-14
Specifications
Processor Types ............................................................ C-2
Core Logic .................................................................... C-2
LCD .............................................................................. C-2
Security ......................................................................... C-2
Memory ......................................................................... C-2
BIOS ............................................................................. C-2
Video Card Options ...................................................... C-3
Storage Options ............................................................ C-3
Audio ............................................................................ C-4
Keyboard & Pointing Device ........................................ C-4
PCMCIA ....................................................................... C-4
I/O Ports ........................................................................ C-4
Communication ............................................................. C-5
Operating Systems Supported ....................................... C-5
Power Management ...................................................... C-5
Power ............................................................................ C-5
Environmental Spec ...................................................... C-5
Physical Dimensions & Weight .................................... C-6
Optional ........................................................................ C-6
Preface
XVII
Preface
XVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 The Storage Devices (hard disk, optical device, Card Reader, PC Card), Mouse, Audio &
Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software, or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Bluetooth, Wireless LAN, PC Camera, TV Tuner and RAID
modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A A definition of the interface, ports/jacks which allow your computer communicate with external
devices.
• Appendix B Information on the NVIDIA Video driver controls.
• Appendix C The computer’s specification.
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1, “Upgrading The Computer” on
page 6 - 1 and “Modules” on page 7 - 1 of the Manual. You may also find notes marked with a
of interest.
Beginners and Not-So-Advanced Users
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Not Included
Operating Systems (e.g. Windows XP etc.) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
1 - 2 Overview
Quick Start Guide
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the following operating systems:
• Microsoft Windows XP Home & Professional Editions & Media Center Edition (with Service Pack 2)
• Microsoft Windows XP 64-Bit Edition
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4
- 6. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
system hasn’t been properly configured (your service representative may have already done that for you), refer to “What
to Install” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
RAID Setup
1
Note that setting up the RAID system and installing the driver for Windows needs to be done when installing the Windows
OS, and therefore before installing the other drivers etc. (see “RAID Setup” on page 7 - 11).
Overview 1 - 3
1
Quick Start Guide
System Startup
2
1 1
1. LCD Latches
2. LED Power & Communication
Indicators
Figure 1 - 1 - Top Panel with LCD Closed
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the
notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack at the rear of the
computer, then plug the AC power cord into an outlet, and
connect the AC power cord to the AC/DC adapter.
5. Move and hold the LCD latches in the direction of the arrows
to release the top cover.
6. Raise the lid/LCD to a comfortable viewing angle (DO NOT
EXCEED AN ANGLE of 120 degrees), and press the power
button to turn the computer “on”.
7. Adjust the LCD panel to a comfortable viewing angle.
8. The LED indicators show the power and battery status of the
computer.
2
1
Shutdown
Please note that you should always shut your computer down by choosing the Shut Down/Turn Off Computer command
from the Start menu in Windows. This will help prevent hard disk or system problems.
1 - 4 Overview
System Map: Top View with LCD Panel Open
Quick Start Guide
1
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft is
usually prohibited. Make
sure the module(s) are
OFF if you are using the
computer aboard aircraft.
The key combination Fn +
F11 toggles power to the
WLAN module, and the
AP-Key to the Bluetooth module.
LCD Angle
When raising the LCD DO
NOT FORCE it in excess
of angle of 120 degrees.
1
2
6
3
5
4
7
8
9
10
Figure 1 - 2 - Top View with LCD Panel Open
1. Optional Built-In PC
Camera
2. LCD
3. LED Power &
Communication
Indicators
4. Speakers
5. AP-Key Buttons &
Power Button
6. Built-In Microphone
7. LED Status Indicators
8. Keyboard
9. TouchPad and Buttons
4
10. Consumer Infrared
Transceiver*
*Enabled with Optional Mini-
PCI TV Tuner Only
5
7
System Map: Top View with LCD Panel Open 1 - 5
1
Quick Start Guide
LED Indicators
The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators)
on the computer display helpful information about the
current status of the computer.
Table 1 - 1 - LED Status Indicators
Icon Color Description
Green
Green
Green
Green Hard Disk/Optical Device Activity
Green Number Lock Activated
Green Caps Lock Activated
The (optional) PC Camera is
powered On
The (optional) Bluetooth Module
is powered On
The (optional) Wireless LAN
Module is powered On
Table 1 - 2 - LED Power & Communication Indicators
Icon Color Description
Orange DC Power is Plugged In
Green The Computer is On
Blinking Green
Orange The Battery is Charging
Green The Battery is Fully Charged
Blinking Orange
Blinking Green New Mail Has Arrived
The Computer is in Stand by
Mode
The Battery Has Reached
Critically Low Power Status
Green
Scroll Lock Activated (to activate
press Fn & Scr Lk)
1 - 6 System Map: Top View with LCD Panel Open
Quick Start Guide
1
AP-Key Buttons
These buttons power on/off the optional PC Camera
and Bluetooth modules, access the internet and e-mail,
and enable/disable high performance video.
Table 1 - 3 - AP-Key Buttons
AP-Key Function
Enable/Disable High Performance Video
Enable/Disable the optional
PC Camera Module
Enable/Disable the optional
Bluetooth Module
Activate the Default E-mail Program
Activate the Default Internet Browser
3D AP-Key Button
Use this button to enable/disable high performance
video when powered by the AC/DC adapter (the 3D
AP-Key button will be illuminated in blue when in
high performance video mode).
If you switch from AC Power to battery power the system will automatically change to a lower performance
video mode setting. High Performance Video can
not be enabled when the system is battery powered.
The system will retain in memory the last known video
performance setting if you switch back from battery to
AC power.
Function Keys & Numeric Keypad
The keyboard has an embedded numerical keypad for
easy numeric data input (see Figure 1 - 3
8).
Activate the Number Lock feature by pressing the
Num Lk key on the top right of the keyboard. You
may check if Number Lock is enabled or not by looking at the LED status indicators.
on page 1 -
System Map: Top View with LCD Panel Open 1 - 7
1
Quick Start Guide
Table 1 - 4 - Function Keys
Keys Description
Fn Function Key
Fn + F1 TouchPad Toggle
Fn + F2
Fn + F3 Mute Toggle
Fn + F4 Sleep Toggle
Fn + F5 Decrease Audio Volume
Fn + F6 Increase Audio Volume
Fn + F7 Display Toggle
Fn + F8 Decrease LCD Brightness
Fn + F9 Increase LCD Brightness
Fn + F11 WLAN Module Toggle
Fn + Scr
Lk
SRS WOW Surround
Sound Toggle
Scroll Lock Toggle
Figure 1 - 3 - Keyboard
Function Keys
Num Lk & Scr Lk Keys
Numeric
Keypad
Fn Key
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use
any standard USB keyboard. The system will detect and enable it automatically. However special functions/AP-Keys unique to the system’s regular
keyboard may not work.
1 - 8 System Map: Top View with LCD Panel Open
System Map: Front & Rear Views
1
2
Overheating
To prevent your computer from overheating make sure nothing blocks the vent(s)/fan intake(s)
while the computer is in use.
3
4
5
3 3
S-Video/Composite Cable HDTV Cable
6
The 7-pin S-Video Out jack requires an adapter cable (7-pin S-Video plug to
4-pin S-Video jack adapter) in order to connect to a standard S-Video cable
(the y-cable pictured includes a yellow composite video jack).
8
7
1
10
9
7-Pin S-Video-Out Jack
11
Quick Start Guide
Figure 1 - 4
Front & Rear Views
1. LCD Latches
2. Consumer Infrared
Transceiver*
3. 7-Pin S-Video-Out
Jack
4. DVI-Out Port
5. DC-In Jack
6. Vent/Fan Intake
7. RJ-11 Phone Jack
8. 2 * USB 2.0 Ports
9. Serial Port
10. S-Video-In Jack*
11. Security Lock Slot
*Enabled with Optional Mini-
PCI TV Tuner Only
1
System Map: Front & Rear Views 1 - 9
1
Quick Start Guide
System Map: Left View
Figure 1 - 5
Left View
1. S/PDIF-Out Jack
2. Line-In Jack
(see page A - 3)
3. Microphone-In Jack
4. Headphone-Out Jack
5. Optical Device Drive Bay (for CD/DVD Device)
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened
paper clip into the emergency eject hole. Do not use a sharpened
pencil or similar object that may break and become lodged in the
hole. Don’t try to remove a CD/DVD/floppy disk while the system
is accessing it as this may cause the system to “crash”.
Headphone Warning
Remove headphones from your ears when shutting the computer
down in order to prevent the higher level shutdown sound from
causing hearing damage.
3152 4
Changing DVD Regional Codes
Go to the Control Panel and double-click System
> Hardware (tab), click Device Manager, then
click the + next to DVD/CD-ROM drives. Doubleclick on the DVD-ROM device to bring up the
Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you
to adjust the regional code (see “DVD Regional
Codes” on page 2 - 5).
DVD region detection is device dependent, not
OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent.
This cannot be altered even if you change your operating system or you use the module in another
computer.
1 - 10 System Map: Left View
System Map: Right View
V
1
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) /
MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) /
Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
The Mini-IEEE 1394a port only supports SELF POWERED IEEE 1394a devices.
3
2
3 3 4 5
7-in-1 Card Reader
Mini-IEEE 1394a
6 7
Quick Start Guide
Figure 1 - 6 - Right View
1. PC Card Slot
2. Mini-IEEE 1394a Port
3. 3 * USB 2.0 Ports
4. TV Antenna Jack
(an adapter is provided for
CATV connection)
5. 7-in-1 Card Reader
6. Infrared Transceiver
(see page 2 - 12)
7. RJ-45 LAN Jack
*
*Enabled with Optional Mini-PCI T
Tuner Only
1
System Map: Right View 1 - 11
1
Quick Start Guide
System Map: Bottom View
Figure 1 - 7 - Bottom View
1. Battery
2. Battery Release Latch
3. CD/DVD Device Release Latch
4. Hard Disk Bay Cover
5. Vent/Fan Intake
6. Sub Woofer
7. Component Bay Cover
8. Speakers
5
5
5
5
1
7
5
2
CPU
The CPU is not a user serviceable part. Opening this
compartment, or accessing the CPU in any way, may violate your warranty.
5
5
5
6
4
8 8
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery
at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 9 for full instructions.
1 - 12 System Map: Bottom View
3
Quick Start Guide
Windows XP Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows XP are accessed from the Start menu. When
you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be
placed in the Start menu and/or the desktop. You can customize the look of the Start menu by right-clicking
the Start menu and selecting Properties from the menu.
Figure 1 - 8
Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu. The Control Panel allows you to configure the settings for most of the
key features in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic control panels for
many of the features, however many new control panels are added (or existing ones are enhanced) when you
install the drivers listed in Table 4 - 1, on page 4 - 6. To see all controls it may be necessary to toggle off
gory View
.
Cate-
1
Windows XP Start Menu & Control Panel 1 - 13
1
Quick Start Guide
Video Features
This computer features an NVIDIA Scalable Link Interface (SLI) that improves graphic quality and performance by combining dual NVIDIA GPUs in a single system to allow the two graphics cards to run in parallel.
You can switch display devices, and configure display options, from the Display Properties control panel in
Windows as long as the appropriate video driver is installed. To access Display Properties in Windows:
1. Click Start, point to Settings and click Control Panel (or just click Control Panel).
2. Double-click Display (icon) - In the Appearances and Themes category.
3. Click Settings (tab) in the Display Properties dialog box.
(You can also access Display Properties by right-clicking the desktop and scrolling down and clicking
Properties.)
4. Move the slider to the preferred setting in Screen area/resolution (Figure 1 - 9 on page 1 - 15).
5. Click the arrow, and scroll to the preferred setting In Colors/Color quality
6. Click Advanced (button) (Figure 1 - 9 on page 1 - 15) to bring up the Advanced properties tabs.
7. Click GeForce Go/Quadro FX (tab).
8. Clicking the tabs or Additional Properties allows you to make any video adjustments you require.
3
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or
TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the S-
Video-Out jack.
Video Driver Controls” on page B - 1 for more detailed video information.
See Table 1 - 9 on page 1 - 15 for a summary of the display modes available, and see “NVIDIA
1
2
(Figure 1 - 9 on page 1 - 15).
1 - 14 Video Features
Quick Start Guide
1
1
2
3
Figure 1 - 9 - Display Properties Desktop
Display Mode Description
Single One of the connected displays is used as the display device
Clone Both connected displays output the same view
Dualview Both connected displays are treated as separate devices, and act as a virtual desktop
Video Features 1 - 15
Table 1 - 5
Display
Options
1
Quick Start Guide
Power Management Features
The Power Options control panel in Windows (see page 1 - 13) allows you to configure power management
features for your computer. You may conserve power through individual components such as the monitor or hard
disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power
throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 10). Pay at-
tention to the instructions on battery care in “Battery Information” on page 3 - 9.
Figure 1 - 10 - Power Options
The computer’s power button, sleep button (Fn + F4 key combination), and lid (closing the lid) may be set to
send the computer in to either Stand by or Hibernate mode.
Power Saving and Performance
Power Schemes may have an affect on your computer performance (see “Power Schemes” on page 3 - 4).
1 - 16 Power Management Features
Storage Devices, Mouse, Audio & Printer
Chapter 2: Storage Devices, Mouse, Audio & Printer
Overview
Read this chapter to learn more about the following main features and components
of the computer:
• Hard Disk Drive
• Optical Device
• 7-in-1 Card Reader
• PC Card Slot
• Auto Mail Checker
• TouchPad and Buttons/Mouse
• Audio Features
• Configuring the Infrared Settings for FIR
• Adding a Printer
2
Overview 2 - 1
Storage Devices, Mouse, Audio & Printer
2
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Power Safety
Figure 2 - 1
Hard Disk Location
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height
of 9.5 mm. The hard disk is accessible from the bottom of your computer as seen
below. Further details on removing and inserting the hard disk are available in “Up-
grading the Hard Disk Drive(s)” on page 6 - 4.
1
1
2 - 2 Hard Disk Drive
Storage Devices, Mouse, Audio & Printer
Optical Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage Options” on page C -
3). The optical device is usually labeled “Drive D:” and may be used as a boot de-
vice if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole
3
to open the tray.
1
2
2
1
3
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-
dows. Click the Volume
icon on the taskbar to
check the setting.
Peripherals must be
connected before you
turn on the system.
Figure 2 - 2
Optical Device
2
Optical Device 2 - 3
Storage Devices, Mouse, Audio & Printer
2
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
Handling CDs or DVDs
2 - 4 Optical Device
Storage Devices, Mouse, Audio & Printer
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 10.
.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2
3
4
5
6 China
Western Europe, Japan, South
Africa, Middle East & Egypt
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
South & Central America, Mexico,
Australia,
New Zealand
N Korea, Russia, Eastern Europe,
India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Figure 2 - 3
DVD Regions
Optical Device 2 - 5
Storage Devices, Mouse, Audio & Printer
2
Card Reader Cover
Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust getting in to the card reader.
7-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device.
• MMC (MultiMedia Card)
• SD (Secure Digital)
• MS (Memory Stick)
• MS (Memory Stick Pro)
• MS Duo (requires PC adapter*)
• Mini SD (requires PC adapter*)
• RS MMC (requires PC adapter*)
*Note: The PC adapters are usually supplied with these cards.
Figure 2 - 4
Right View
1. Card Reader
1
2 - 6 7-in-1 Card Reader
Storage Devices, Mouse, Audio & Printer
PC Card Slot
The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC Card.
Inserting and Removing PC Cards
• Align the PC Card with the slot and push it in until it locks into place.
• To remove a PC Card, simply press the eject button next to the slot.
1
1
PC Card Cover
Make sure you keep the
cover in the PC Card
slot when not in use.
This will help prevent
foreign objects and/or
dust getting in to the
slot.
Figure 2 - 5
PC Card Slot
2
PC Card Slot 2 - 7
Storage Devices, Mouse, Audio & Printer
2
Figure 2 - 6
Auto Mail Checker
Auto Mail Checker
After you have installed the driver for the Auto Mail Checker program (see “Auto-
Mail Checker” on page 4 - 10) you may then configure it to give you notification
when you receive new mail. You must be online to receive this notification (note that
this program only supports the POP3 protocol), and your default mail program does
not need to be open.
When the program is run, the Auto Mail Checker appears as an icon in the task-
bar (to run the program go to Start > Programs/All Programs > Auto Mail
Checker > Auto Mail Checker). Right clicking on the icon will bring up the fol-
lowing options menu. If you have not input your mail account data, then you will be
prompted to do so.
Select Open to bring up the control panel for the program.
2 - 8 Auto Mail Checker
Storage Devices, Mouse, Audio & Printer
You may then configure the options for your mailserver, name, password, program
and method(s) of notification.
Note
Check with your Internet
Service Provider, network administrator or
Mail Service provider for
details on what to put on
these pages.
Figure 2 - 7
Auto Mail Checker
Account Setup and
Options
2
Auto Mail Checker 2 - 9
Storage Devices, Mouse, Audio & Printer
2
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to
Mouse Driver
If you are using an external mouse your operating system may be
able to auto-configure
your mouse during its
installation or only enable its basic functions.
Be sure to check the
device’s user documentation for details.
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse.
Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 9) you
can configure the functions by double-clicking the TouchPad driver icon on the
taskbar. You may then configure the TouchPad tapping, buttons, scrolling, pointer
motion and sensitivity options to your preferences. You will find further information
at www.synaptics.com.
Figure 2 - 8
Mouse Properties
2 - 10 TouchPad and Buttons/Mouse
Storage Devices, Mouse, Audio & Printer
Audio Features
You can configure the audio options on your computer from the Sounds and Audio
Devices Windows control panel (see Figure 1 - 8 on page 1 - 13), or from the
Sound Manager icon in the taskbar/control panel (this will bring up the AC97
Audio Configuration menu). Adjust the volume by using the Fn + F5/F6 key combination.
The audio system features SRS WOW Surround Sound Technology inside
(SRS/ TruSurround/ TruBass / Focus Enhancement). SRS WOW Surround Sound
may be toggled on/off using the Fn + F2 key combination.
Note that audio input through Line-in will default to the mute setting. To set up your
audio sources to play though the Line-in jack go to the Sounds and Audio Devices
Windows control panel and make sure the Mute box is not ticked.
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-
dows. Click the Volume
icon on the taskbar to
check the setting.
Figure 2 - 9
AC97 Audio
Configuration
Menus
2
Audio Features 2 - 11
Storage Devices, Mouse, Audio & Printer
2
The infrared transceiver
operates on a “Line of
Sight”.
Make sure nothing is
blocking the “Line of
Sight” between your
system’s transceiver
and the destination’s
transceiver.
Infrared
Communication
Configuring the Infrared Settings for FIR
To configure your computer’s infrared port (on the right of the computer) for Far Infrared (FIR) communication follow these steps:
1. Click Start, point to Settings and click Control Panel (or just click Start > Control
Panel).
2. Double-click Wireless Link (Printers and Other Hardware Category) icon.
3. Click Hardware (tab), and click the Properties button, then click the Advanced
(tab).
4. Select “Infrared Transceiver A” and change the Value to “HP HSDL-2300/
3600”.
5. Click OK > OK.
6. Restart the computer if prompted to do so.
You can enable/disable the infrared transceiver in the BIOS (see “I/O Device Con-
figuration (Advanced Menu)” on page 5 - 10). For further information, please refer
to the manual of the device you wish to connect.
2 - 12 Configuring the Infrared Settings for FIR
Storage Devices, Mouse, Audio & Printer
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer, however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most new printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instructions (unpacking, paper tray, toner/ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar
(you will need to purchase a parallel to USB converter).
Parallel Printer
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
2
Adding a Printer 2 - 13
Storage Devices, Mouse, Audio & Printer
2
2-14
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer uses the ACPI
power management system. Power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole
system.
This chapter covers:
• The Power Sources
• Turning on the Computer
• Power Schemes
• System Power Options
• Configuring the Power Button
• Battery Information
Advanced Configuration and Power Interface
The ACPI interface provides the computer with enhanced power saving techniques
and gives the operating system (OS) direct control over the power and thermal states
of devices and processors. For example, it enables the OS to set devices into lowpower states based on user settings and information from applications. ACPI is fully
supported in Windows XP.
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
(Note: All pictures used
on the following pages
are from the Windows
XP OS.)
3
Overview 3 - 1
Power Management
The Power Sources
3
Power Button as
Stand by or
Hibernate Button
If you are using a fully
ACPI-compliant OS,
(such as Windows XP)
you can use the OS’s
“Power Options” control
panel to set the power
button to send the system into Stand by or Hibernate mode (see your
OS’s documentation, or
“Configuring the Power Button” on page 3 8 for details).
The computer can be powered by either an AC/DC adapter or a battery pack.
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components (see page C - 5).
1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then connect the AC power cord to the
AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 12).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 9.
3 - 2 The Power Sources
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Stand by/Hibernate/
Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and
holding the power button for longer than this will shut the computer down). Use
Power Options in the Windows control panel to configure this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow-
er button for 4 seconds, or longer, to force the system to turn itself off.
Power Management
Shutdown
Note that you should always shut your computer down by choosing the
Shut Down/Turn Off
Computer command
from the Start menu in
Windows. This will help
prevent hard disk or system problems.
3
Turning on the Computer 3 - 3
Power Management
Power Schemes
3
Resuming
Operation
Press a key on the keyboard to have the system resume from
Monitor or Hard Disk
Stand by.
Figure 3 - 1
Power Schemes
You can set your computer to conserve power through individual components by
means of Power Schemes. You can also adjust the settings for each scheme to set
the monitor to turn off after a specified time, and the computer's hard disk motor to
turn off if the hard disk drive has not been accessed for a specified period of time (if
the system reads or writes data, the hard disk motor will be turned back on). The
schemes may also be set to set a specified time for the system to enter Stand by or
Hibernate modes (see “System Power Options” on page 3 - 6).
3-4Power Schemes
Each Windows Power Scheme will also adjust the processor performance of your
machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source. Choose the Max Battery scheme (bear
in mind that this scheme may slow down the overall performance of the computer in
order to save power) for maximum power saving when the computer is battery (DC
power) powered.
Windows will use Portable/Laptop as the default scheme.
TV Recording and Power Schemes
If you intend to use the optional TV Tuner to record live TV, then go to the Power Options
control panel and set the power scheme to Always On in order to prevent the power saving
options from adjusting the computer’s performance level.
Power Management
3
Power Schemes 3 - 5
Power Management
System Power Options
You can use the system power options to stop the computer’s operation and restart
3
where you left off. This system features Stand by and Hibernate sleep mode levels
(Hibernate mode will need to be enabled by clicking the option in the Hibernate
tab in the Power Options control panel - Figure 3 - 2 on page 3 - 7).
Hibernate Mode vs. Shutdown
Hibernate mode and Shutdown are the same in that the system is off and you need
to press the power button to turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left off
(what was on your desktop) without reopening the application(s) and file(s) you last
used.
You can use either method depending on your needs.
Stand by Mode vs. Hibernate Mode
If you want to stay away from your work for just a while, you can put the system on
Stand by instead of in hibernation. It takes a longer time to wake up the system from
Hibernate mode than from Stand by mode.
3 - 6 System Power Options
Stand by
Stand by saves the least amount of power, but takes the shortest time to return to full
operation. During Stand by the hard disk is turned off, and the CPU is made to idle
at its slowest speed. All open applications are retained in memory. When you are not
using your computer for a certain length of time, which you specify in the operating
system, it will enter Stand by mode to save power.
Hibernate
Hibernate uses no power and saves all of your information on a part of the HDD before it turns the system off. Although it saves the most power it takes the longest time
to return to full operation. You can set your computer to automatically enter Hibernate mode when the battery power is almost depleted. You will need to enable Hibernate mode from the Hibernate tab in the Power Options control panel. The
system will resume from Hibernate mode by pressing the power button.
Power Management
System Resume
The system can resume
from Stand by mode by:
• Pressing the power
button
• Pressing the Fn + F4
key combination
• An alarm resume that
is enabled and
expires
• An incoming call
received on the
modem (if enabled)
• Network card activ-
ity (if enabled)
3
Figure 3 - 2
Enable Hibernation
System Power Options 3 - 7
Power Management
Configuring the Power Button
The power button may be set to send the computer in to either Stand by or Hiber-
3
Figure 3 - 3
Power Options
(Advanced - Power
Buttons)
nate mode. In Stand by mode, the LED will blink green. In Hibernate mode
the LED will be off. If you are in a power saving mode set to save power through
individual components (e.g. hard disk, monitor), the LED will remain green.
Power Button Sleep/ResumeLid
You may also configure the Sleep/Resume key combination (Fn + F4) from the menu illus-
trated in Figure 3 - 3. In Windows this is referred to as the Sleep button.
3 - 8 Configuring the Power Button
(Sleep) Button
Sleep Button
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 12 for instructions on how to do this).
Battery Life
Your computer’s battery life is dependent upon many factors, including the programs you are running, and peripheral devices attached. Power Options (you may
set low battery Alarms and actions, and check the Power Meter from the Power
Options control panel), and settings in the OS will help prolong the battery life if
configured appropriately.
Power Management
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 4
Power Options
(Alarm & Power
Meter)
3
Battery Information 3 - 9
Power Management
Battery life may be shortened through improper maintenance. To optimize the life
3
Conserving Battery
Power
To conserve battery power:
Lower the brightness level
of the LCD display. The
system will decrease LCD
brightness slightly to save
power when it is not powered by the AC/DC adapter.
Close modem or communication applications when
they are not being used.
Remove any unused PC
Cards from the computer
(PC Cards quickly use up
battery power even if the
system enters sleep
mode).
Disconnect any unnecessary external devices.
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3.
3D AP-Key Button
The system will default to high performance video when powered by the AC/DC
adapter (the 3D AP-Key button will be illuminated in blue). If you switch from AC
power to battery power the system will automatically change to a lower performance
video mode setting in order to save power. High Performance Video can not be
enabled when the system is battery powered (see “3D AP-Key Button” on page 1
- 7).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 6 for information on the battery charge status, and to “Battery Information” on page 3 - 9 for more information on how to maintain and properly
recharge the battery pack.)
3 - 10 Battery Information
Proper handling of the Battery Pack
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Damaged Battery Warning
Should you notice any physical defects (e.g. the battery is bent out of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has been dropped we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is
recommended that you replace your computer battery every two years.
Power Management
3
Battery Information 3 - 11
Power Management
Battery FAQ
3
Danger of explosion if
battery is incorrectly replaced.
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Caution
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer by yourself even when you see a message that indicates the
battery is critically low, just let the computer use up all of the battery power and shut
down on its own. Disable the Power Options functions in the Control Panel, especially any Alarms (unclick the tickboxes - see 3 - 9) and Schemes (change all the
settings to Never - see page 3 - 4). As the battery nears the end of its life save and
close any critical files.
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
3 - 12 Battery Information
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some
of the computer’s subsystems. The system takes advantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to
manually install some system-required drivers and
utilities. The following operating systems are covered.
• Microsoft Windows XP Home Edition
(with Service Pack 2)
• Microsoft Windows XP Professional Edition
(with Service Pack 2)
• Microsoft Windows Media Center Edition
(with Service Pack 2)
• Microsoft Windows XP 64-Bit Edition
What to Install
The Device Drivers & Utilities + User’s Manual CDROM contains the drivers and utilities necessary (ex-
cept those for the optional TV Tuner which are on a
separate CD provided) for the proper operation of the
computer. Table 4 - 1
to install manually, and it is very important that the
drivers are installed in the order indicated.
Module Driver Installation
The procedures for installing drivers for the Wireless
LAN, Bluetooth, PC Camera and RAID modules are
provided in “Modules” on page 7 - 1.
RAID Setup
Note that setting up the RAID system and installing
the driver for Windows needs to be done when installing the Windows OS, and therefore before installing
the other drivers listed here (see “RAID Setup” on
page 7 - 11).
on page 4 - 6 lists what you need
4
What to Install 4 - 1
Drivers & Utilities
Navigate (Browse..) to D:
You will notice that many of the instructions for driver
4
installation require you to “Navigate (Browse) to D:”.
We assume that you will install all drivers and utilities
from the built-in CD device and it is assigned to “Drive
D:”. In addition, all file extensions can be seen
In this case “D:” is the drive specified for your CD device. Not all computers are setup the same way, and
some computers have the CD listed under a different
drive letter - e.g. if you have two hard drives (or hard
disk partitions) one may be designated as “Drive C:”
and the other as “Drive D:”. In this case the CD device
may be designated as “Drive E:” - Please make sure
you are actually navigating to the correct drive letter
for the CD device.
When you click the Browse (button) after clicking
Run in the Start menu you will see the “Look in:” di-
alog box at the top of the Browse window. Click the
scroll button to navigate to My Computer to display
the devices and drive letters.
Figure 4 - 1 - Navigate (Browse..) to..
4 - 2 What to Install
Service Packs
Check the warnings on the following pages regarding
installation of the appropriate Service Pack for your
Windows OS (Note: Service Pack 2 is not required
for Windows XP 64-Bit Edition). If you are unsure of
the Service Pack currently installed see below. Make
sure you have installed the appropriate Service Pack
before installing all the drivers.
Service Pack Installed
To see which Service Pack is currently installed on your
computer go to the General tab of the System control
panel. Right-click the My Computer icon on the desktop
or in the Start menu and select Properties. The Service
Pack currently installed on your system will be listed under the “System:” heading. (If no Service Pack information is listed, then no Service Pack is installed.)
Drivers & Utilities
Windows XP Service Pack 2
Make sure you install Windows XP Service Pack 2 (or
a Windows XP version which includes Service Pack 2)
before installing any drivers. Service Pack 2 includes
support for USB 2.0. (Not Required for Windows XP
64-Bit Edition.)
If you have upgraded the system by installing Service
Pack 2 (i.e. your Windows XP version does not include
Service Pack 2) then follow these instructions:
1.Click Start (menu), point to Settings and click Control
Panel (or click Control Panel).
2.Double-click System (icon); System (icon) is in Per-
formance and Maintenance (category).
3.Click the Hardware (tab) > Device Manager (button).
4.Click “+” next to Other Devices (if its sub-items are not
shown).
5.Right-click Universal Serial Bus (USB) Controller
and select Uninstall > OK (if you don’t see the item
then there is no need to take any further action).
6.Restart the computer and it will find the USB 2.0 controller.
4
What to Install 4 - 3
Drivers & Utilities
Authorized Driver Message
If you receive a message telling you that the driver you
are installing is not authorized (Digital Signature Not
Found), just click Yes or Continue Anyway to ignore
the message and continue the installation procedure.
4
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
Version Conflict Message
During driver installation if you encounter any “file
version conflict” message, please click Yes to choose
to keep the existing (newer) version.
New Hardware Found
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installa-
tion procedure (other than when outlined in the
driver install procedure), click Cancel to close the
window, and follow the installation procedure.
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Add/Remove Programs item. If you
see the individual driver listed (if not see below), uninstall it, following the on screen prompts (it may be
necessary to restart the computer). Go to the appropriate section of the manual to complete the update/reinstall procedure for the driver in question.
If the driver is not listed in the Add/Remove Pro-
grams item:
1. Click Start (menu), point to Settings and click Control
Panel (or click Start > Control Panel).
2. Double-click System (icon); System (icon) is in
Performance and Maintenance (category).
3. Click Hardware (tab) > Device Manager (button).
4. Double-click the device you wish to update/reinstall the
driver for (you may need to click “+”).
5. Look for the Update Driver button (check the Driver tab)
and follow the on screen prompts.
4 - 4 What to Install
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
CD-ROM and click Install WinXP Drivers (button),
or Optional (button) to access the Optional driver
menu.
If you wish to install the drivers manually see page 4 -
6
.
1. Check the driver installation order from Table 4 - 1
on page 4 - 6 (all the drivers must be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install. After
installing each driver it will become grayed out (if
you need to reinstall any driver, click Unlock).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
4
Figure 4 - 2 - Drivers Installer Screen 1
Figure 4 - 3 - Drivers Installer Screen 2
Driver Installation 4 - 5
Drivers & Utilities
Windows XP Home/Professional & Windows XP MCE (SP2)/ Windows XP x64
Driver Page Driver Page
Chipset
4
Video (VGA)
Audio
Modem
LAN
AP-Key Utility
TouchPad
Page 4 - 7
Page 4 - 7
Page 4 - 7
Page 4 - 8
Page 4 - 8
Page 4 - 9
Page 4 - 9
PCMCIA
AMD Processor
AutoMail Checker
Bluetooth Module
WLAN Module
PC Camera Module
Page 4 - 10
Page 4 - 10
Page 4 - 10
Page 7 - 2
Page 7 - 4
Page 7 - 6
Table 4 - 1 - Driver Installation
Manual Driver Installation
If you wish to install the drivers manually, click the Exit button to quit the Drivers Installer application, and
then follow the manual installation procedure for each driver. The manual installation procedure begins with instructions on how to browse to the executable file; “Click Start (menu) > Run
..”.
4 - 6 Driver Installation
Drivers & Utilities
WinXP Driver Installation Procedure
RAID Setup
Note that setting up the RAID system and installing the
driver for Windows needs to be done when installing the
Windows OS, and therefore before installing the other
drivers etc. (see “RAID Setup” on page 7 - 11).
Chipset
1. Click 1.Install Chipset Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\00CHIPSET\setup.exe and click
OK.
2. Click Next > Next > Next > Yes.
3. Click Finish to restart the computer.
Video
1. Click 2.Install Video Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\01VIDEO\setup.exe and click
OK.
2. Click Next.
3. Click “Yes, I want to restart the computer
now.”, and click Finish to restart the computer.
Audio
1. Click 3.Install Audio Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\02AUDIO\setup.exe and click
OK.
2. Click Next (click Continue Anyway if asked if
you want to continue at any time).
3. Click Finish to restart the computer.
4
Driver Installation 4 - 7
Drivers & Utilities
Modem
1. Click 4.Install Modem Driver > Yes.
OR
Click Start (menu) > Run... and navigate
4
(Browse..) to
D:\Drivers\03MODEM\ssetup.exe
OK.
2. Click OK.
3. The modem is now ready for configuration.
Modem Country Selection
Be sure to check if the modem country selection is appropriate for you (Control Panel > Phone and Modem
Options).
and click
LAN
1. Click 5.Install LAN Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\04LAN\setup.exe and click OK.
2. Click Next.
3. Click Install > Finish.
4. The network settings can now be configured.
4 - 8 Driver Installation
Drivers & Utilities
AP-Key Utility
1. Click 6.AP-Key Utility > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\05AP-Key\AKSETUP.exe and
click OK.
2. Click Next.
3. Click Finish to restart your computer.
TouchPad
1. Click 7.Install Touchpad Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse...) to
D:\Drivers\06TOUCHPAD\setup.exe and
click OK.
2. Click Next > Next > Next (click Continue
Anyway if asked if you want to continue at any
time).
3. Click Finish to restart your computer.
4. You may then configure your TouchPad as outlined in “TouchPad and Buttons/Mouse” on
page 2 - 10.
4
Driver Installation 4 - 9
Drivers & Utilities
PCMCIA
1. Click 8.Install PCMCIA Driver > Yes.
OR
Click Start (menu) > Run... and navigate
4
(Browse..) to D:\Drivers
\07PCMCIA\setup.exe and click OK.
2. Click Next.
3. Click the button to accept the license, and then
click Next.
4. Click Finish.
AMD Processor
1. Click 9.Install AMD CPU Driver > Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to
D:\Drivers\08AMD\setup.EXE and click OK.
2. Click Next.
3. Click the button to accept the license, and then
click Next.
4. Click Finish > Yes to restart the computer.
AutoMail Checker
1. Click Optional > 1.Install Automail Utility >
Yes.
OR
Click Start (menu) > Run... and navigate
(Browse..) to D:\Drivers\
09AUTOMAIL\Setup.EXE and click OK.
2. To continue click Next > Next > Finish.
3. Run the program from the Auto Mail Checker
in the Start menu (Start > Programs/All Pro-
grams > Auto Mail Checker).
4. Click the icon in the taskbar to input the email account details.
5. For further details see “Auto Mail Checker” on
page 2 - 8.
4 - 10 Driver Installation
Drivers & Utilities
Module Drivers
See the pages indicated for the driver installation procedures for any modules included in your purchase option.
Bluetooth
See the install procedure in “Bluetooth Driver Instal-
lation” on page 7 - 2.
Wireless LAN
See the appropriate install procedure for your WLAN
module in “802.11 b/g WLAN Driver Installation” on
page 7 - 4.
PC Camera
See the install procedure in “PC Camera Module” on
page 7 - 6.
RAID
See the setup procedure for your RAID module in
“RAID Setup” on page 7 - 11.
TV Tuner
The drivers and utilities for the optional TV Tuner are
provided on a separate CD. Some general guidelines
are outlined in “Mini-PCI TV Tuner Module Op-
tions” on page 7 - 25.
4
Driver Installation 4 - 11
Drivers & Utilities
4
4-12
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The PhoenixBIOS Setup Utility
If your computer has never been set up, or you are making important changes to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in the PhoenixBIOS Setup Utility. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
Overview 5 - 1
BIOS Utilities
Phoenix FirstBIOS Desktop Pro
Copyright 1985-2004 Phoenix Technologies Ltd.
All Rights Reserved
BIOS Revision: XXXX
KBC/EC Revision: XXXX
CPU0 = AMD Turion(tm) 64 X2 Mobile Technology TL-50
CPU Stepping = F2E 1600MHz
MemClK = 266Mhz Tcl = 4.0 Trcd=4Tras=9Trp=4
LDT Frequency = 800Mhz LDT Width = 16bit DOWN - 16bit UP
632K System RAM Passed
1022M Extended RAM Passed
512 KB L2 Cache
System BIOS shadowed
Video BIOS shadowed
Press <F2> to enter SETUP
The Power-On Self Test (POST)
POST Screen
1.BIOS information
2.CPU type
3.Memory status
5
4.Enter Setup prompt
appears only during
POST
Note: The POST screen
as pictured is for guideline purposes only.
Figure 5 - 1
POST Screen
Each time you turn on the computer the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run the PhoenixBIOS Setup Utility.
If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.
1
2
3
4
5 - 2 The Power-On Self Test (POST)
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:
• Press <F1> to resume
• <F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct
configuration.
Press F2 to run the Setup program and try to correct the problem. If you still get an
error message after you change the setting, or if the “cure” seems even worse, call
for help.
BIOS Utilities
5
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
The Setup Program
The the PhoenixBIOS Setup Utility program tells the system how to configure itself and manage basic features and subsystems (e.g. port configuration).
Entering Setup
To enter the PhoenixBIOS Setup Utility, turn on the computer and press F2 during
5
the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 on page 5 -
2 is usually present for a few seconds after you turn on the system. If you get a “Key-
board Error”, (usually because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.
5 - 4 The Setup Program
Setup Screens
The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with five (5) menu headings. When you
select a heading, a new screen appears. Scroll through the features listed on each
screen to make changes to the PhoenixBIOS Setup Utility.
Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
BIOS Utilities
Setup Menus
The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configuration appropriate for your
model and options.
5
The Setup Program 5 - 5
BIOS Utilities
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
<Tab>, <Shift Tab>, or
<Enter> selects field.
Main
System Time: [22:11:05]
System Date: [09/09/2006]
Primary Master [CD-ROM]
System Memory: 634 KB
Extended Memory: 1022 MB
VGA Card: nVIDIA 7900 GTX
VBIOS Revision 5.71.22.15.11
VBIOS Build Date 04/25/06
Main Menu
Figure 5 - 2
Main Menu
5
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
5 - 6 Main Menu
Primary Master (Main Menu)
Pressing Enter here opens the sub-menu to show the configuration of hard disks and
CD/DVD device(s) on the computer’s SATA Channels. Use the Auto (Type:) setting to have the items configured automatically for you.
System/Extended Memory: (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
The Main menu also contains information on your video card and video BIOS version.
BIOS Utilities
5
Main Menu 5 - 7
BIOS Utilities
Advanced Menu
Figure 5 - 3
PhoenixBIOS Setup Utility
Advanced Menu
Main Advanced Security Boot Exit
Advanced Chipset Control
5
I/O Device Configuration
Reset Configuration Data: [No]
Boot Logo Screen: [Disabled]
Power on Boot Beep [Disabled]
Battery Low Alarm Beep: [Enabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Advanced
Item Specific Help
Select Each Item to
Enable/Disable
integrated devices
Advanced Chipset Control (Advanced Menu)
Pressing Enter here will access the sub-menu which allows you to disable the audio
and modem devices if required; and you can also Enable/Disable the NVIDIA
RAID Configuration (see over) function from this menu.
5 - 8 Advanced Menu
NV RAID Configuration (Advanced Menu > Advanced Chipset Control)
This menu item allows you to enable/disable NV RAID Configuration for your
hard disk(s). You should only enable/disable this item BEFORE installing an op-
erating system, and after you have backed up all necessary files and data (see sidebar).
BIOS Utilities
RAID
Enable/Disable
Warning
PhoenixBIOS Setup Utility
Advanced
Advanced
Advanced Chipset Control
NV RAID Configuration: [Enabled]
Audio Codec: [Auto]
Modem Codec: [Auto]
Route Port 80h cycles to [LPC]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Enable/Disable
Nvidia RAID control.
SATA controller must
be enabled for RAID
feature to function.
Enabling Master SATA0
Secondary requires
enabling Secondary SATA
Channel.
Both options are listed
in Integrated Devices.
DO NOT Enable/Disable the NV RAID Configuration unless you
intend to reinstall your
operating system. Make
sure you have backed
up all your data before
doing so (see “RAID
Setup” on page 7 - 11).
Figure 5 - 4
Advanced Menu >
Advanced Chipset
Control
Advanced Menu 5 - 9
5
BIOS Utilities
I/O Device Configuration (Advanced Menu)
The sub-menus under this item allow you to enable/disable the Serial port A (Serial
Mouse), and FIR (Infrared) transceiver.
Reset Configuration Data (Advanced Menu)
This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious
5
system conflict that the operating system is unable to boot.
Boot Logo Screen (Advanced Menu)
Set this item to enable or disable the pre-OS startup screen logo display at system
start up.
Power On Boot Beep (Advanced Menu)
Use this menu to enable/disable the single beep sound at the end of the POST. This
item is “Disabled” by default.
Battery Low Alarm Beep: (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
5 - 10 Advanced Menu
Security Menu
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
Security
BIOS Utilities
Figure 5 - 5
Security Menu
Supervisor Password Is: Clear
Set Supervisor Password [Enter]
Password on boot: [Disabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Supervisor Password
controls access to the
setup utility.
Set Supervisor Password (Security Menu)
You can set a password for access to the Setup utility. This will not affect access to
the computer OS, (only the Setup utility) unless you choose to set a Password on
Boot (see over).
5
Security Menu
The changes you
make here affect the
access to the Setup
utility itself, and also
access to your machine as it boots up after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.
Security Menu 5 - 11
BIOS Utilities
Password on boot: (Security Menu)
Password Warning
Specify whether or not a password should be entered to boot the computer. If “Enabled” is selected, only users who enter a correct password can boot the system (see
the warning in the sidebar). The default setting is “Disabled”.
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
5
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter
again to confirm the password clearance.
5 - 12 Security Menu
Boot Menu
BIOS Utilities
PhoenixBIOS Setup Utility
Main Advanced Security Exit
Boot priority order:
1: USB FDC:
2: USB KEY:
3: PCI SCSI: TOSHIBA MK8032GSX
4: IDE CD: UJDA770 DVD/CDRW-(PM)
5: PCI BEV:
6:
7:
8:
Excluded from boot order:
: USB HDD:
: USB CDROM:
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Boot
Item Specific Help
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<x> exclude or include
the device to boot.
When you turn the computer on it will look for an operating system (e.g. WindowsXP) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in
the order specified in the Boot priority order. Item specific help on the right is
available to help you move devices up and down the order.
Figure 5 - 6
Boot Menu
5
Boot Menu 5 - 13
BIOS Utilities
Exit Menu
Figure 5 - 7
Exit Menu
Main Advanced Security Boot Exit
Exit Saving Changes [Enter]
5
Exit Discarding Changes [Enter]
Load Setup Defaults [Enter]
Discard Changes [Enter]
Save Changes [Enter]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Execute Command F10 Save and Exit
PhoenixBIOS Setup Utility
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any
changes you have made to the Setup. You can also choose to restore the original Set-
up defaults that will return the Setup to its original state, and erase any previous
changes you have made in a previous session.
5 - 14 Exit Menu
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:
• A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
• Removing the Battery
• Upgrading the Hard Disk Drive(s)
• Upgrading the System Memory (RAM)
• Upgrading the Optical (CD/DVD) Device(s)
• Removing the Video Card(s)
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
Upgrading The Computer
When Not to Upgrade
Power Safety Warning
These procedures involve opening the system’s case, adding and sometimes replacing parts.You should not perform any of these upgrades if:
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals and
6
cables (including telephone lines). It is advisable to also remove your
battery in order to prevent accidentally turning
the machine on.
6 - 2 Overview
• Your system is still under warranty or a service contract
• You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or replace the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.
Upgrading the Processor
If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may
damage the processor or mainboard.
Upgrading The Computer
Removing the Battery
If you are confident in undertaking upgrade procedures yourself, for safety reasons
it is best to remove the battery.
1. Turn the computer off, turn it over and remove the battery.
2. Slide latch towards the unlock symbol and hold it in place, and slide latch in
the direction of the arrow.
3. Slide the battery out and lift it up and out of the battery bay.
1
3
2
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
2
1
Figure 6 - 1
Battery Removal
6
3
Removing the Battery 6 - 3
Upgrading The Computer
Upgrading the Hard Disk Drive(s)
HDD System Warning
New HDD’s are blank. Before you begin make sure:
You have backed up any
data you want to keep from
your old HDD.
You have all the CD-ROMs
and FDDs required to in-
6
stall your operating system
and programs.
If you have access to the internet, download the latest
application and hardware
driver updates for the operating system you plan to install. Copy these to a
removable medium.
Figure 6 - 2
HDD Bay Cover
Removal
The hard disk drive(s) can be taken out to accommodate other 2.5" serial (SATA)
hard disk drives with a height of 9.5mm (h) (see “Storage Options” on page C - 3).
Follow your operating system’s installation instructions, and install all necessary
drivers and utilities (as outlined in “Drivers & Utilities” on page 4 - 1 & “RAID Set-
up” on page 7 - 11), when setting up a new hard disk(s).
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the hard disk bay cover and remove screws
3. Remove the bay cover .
4
1 3
- .
4
1 3
2
6 - 4 Upgrading the Hard Disk Drive(s)
Upgrading The Computer
4. Slide the hard disk assembly in the direction of the arrow .
5. Remove the hard disk assembly .
6. Remove screws
7. Reverse the process to install a new hard disk(s).
5
6
7 10 11 12
- and separate the bracket from the hard disk .
5
6
6
7
5
12
10
9
11
Figure 6 - 3
HDD Removal
8
6
Upgrading the Hard Disk Drive(s) 6 - 5
Upgrading The Computer
Upgrading the System Memory (RAM)
The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2). The
total memory size is automatically detected by the POST routine once you turn on
your computer.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the component bay cover and remove screws
1 13
- .
6
Figure 6 - 4
Bay Cover Screws
6 - 6 Upgrading the System Memory (RAM)
10
2
1
9
13
3
8
11
4
7
5
6
12
Upgrading The Computer
3. Remove the bay cover .
4. Gently pull the two release latches ( &
the direction indicated by the arrows in Figure 6 - 6.
14
14
15 16
) on the sides of the memory socket in
15 16
Figure 6 - 5
Bay Cover Removal
Contact Warning
Be careful not to touch
the metal pins on the
module’s connecting
edge. Even the cleanest
hands have oils which
can attract particles, and
degrade the module’s
performance.
Figure 6 - 6
RAM Module
Release
6
Upgrading the System Memory (RAM) 6 - 7
Upgrading The Computer
5. The RAM module will pop-up, and you can remove it.
17
Figure 6 - 7
RAM Removal
17
6
6. Pull the latches to release the second module if necessary.
7. Insert a new module holding it at about a 30° angle and fit the connectors firmly
into the memory socket.
8. The module’s pin alignment will allow it to only fit one way. Make sure the module
is seated as far into the socket as it will go. DO NOT FORCE the module; it should
fit without much pressure.
9. Press the module in and down towards the mainboard until the socket levers click
into place to secure the module.
10. Replace the cover and screws (see Figure 6 - 4).
11. Restart the computer to allow the BIOS will register the new memory configuration
as it starts up.
6 - 8 Upgrading the System Memory (RAM)
Upgrading the Optical (CD/DVD) Device(s)
1. Turn the computer off, turn it over and remove the battery.
2. Slide the latch towards the unlock symbol and hold it in place.
3. Slide the optical device out of the computer at point .
1
2
2
1
Upgrading The Computer
6
Figure 6 - 8
Removing the CD/
DVD Device(s)
Upgrading the Optical (CD/DVD) Device(s) 6 - 9
Upgrading The Computer
Removing the Video Card(s)
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the component bay cover and remove screws
3. Remove the bay cover .
14
1 13
- .
6
Figure 6 - 9
Bay Cover Removal
6 - 10 Removing the Video Card(s)
10
2
1
3
8
4
7
5
6
9
11
13
14
12
Upgrading The Computer
4. Remove screws ( & ).
15 18
5. Carefully (a cable is still connected) grip the plastic tag and lift the video card up.
17
19
19
18
15
16
19
18
17
6. Disconnect cable , and lift the video card up off the computer.
15
16
Caution
The heat sink, and video
card area in general,
contains parts which are
subject to high temperatures. Allow the area
time to cool before removing these parts.
Figure 6 - 10
Video Card Removal
6
Removing the Video Card(s) 6 - 11
Upgrading The Computer
6
6-12
Loading...