Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information
contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or
any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear
in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse)
of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators
of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended
as an endorsement of that product or its manufacturer.
© February 2007
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of
this copyright protection technology must be authorized by Macrovision Corporation, and is intended fo r home
or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel Core is a trademarks/registered trademarks of Intel Corporation.
is a trademark of SRS Labs, Inc.
WOW technology is incorporated under license from SRS Labs, Inc.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the
equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury
to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet
basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There
may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may
explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 240V, 50 - 60Hz/ DC Output 20V, 6.5A (130W) minimum).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER, TELE-
COMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class 1 Product
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-
ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
IV
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down proper ly and don ’t for ge t
to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
5. Take care when using peripheral devices.
Use only approved brands of
peripherals.
Do not disassemble the computer by yourself.
Unplug the power cord befor e
attaching peripheral devices.
Perform routine maintenance
on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VI
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for intern ational travel but it still re quires a steady,
uninterrupted power supply. If you are unsure of your local power specifications, consult
your service representative or local power company.
• The power adapter may have either a 2-pr ong or a 3-prong ground ed plug. The third prong
is an important safety feature; do not defeat its purpose. If you do not have access to a
compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be su re to disconnect it by the plug head, not by
its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load
of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even
if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly
result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries
may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life,
under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with
your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the
manufacturer. Discard used battery according to the manufacturer’s instructions.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the
computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the
power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and
screw(s) before turning the computer on.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hard-
ware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a
notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer
from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting,
keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very
common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and
disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note:
Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight.
These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make
sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies)
charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer.
Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time.
Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or
other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly belo w the
level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
• Your knees should be slightly higher than your hips. Place your feet flat on the floor or on
a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree angles
when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent
and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and
shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
XII
Contents
Notice ................................................................................. I
FCC Statement .............................................................II
Instructions for Care and Operation ..........................IV
Power Safety ..............................................................VI
Battery Precautions ...................................................VII
Cleaning .................................................................. VIII
Servicing ................................................................. VIII
Travel Considerations ................................................IX
Preface
System Map: Rear View ..............................................1-12
System Map: Right View .............................................1-13
System Map: Left View ...............................................1-14
System Map: Bottom View ..........................................1-15
Windows Vista Start Menu & Control Panel ...............1-16
Video Features .............................................................1-17
Display Devices & Options .......................................1-18
Power Options ............................................ .... .... ..........1-19
Quick Start Guide
Overview ........................................................................1-1
Advanced Users ...........................................................1-2
Beginners and Not-So-Advanced Users ......................1-2
Warning Boxes ............................................................1-2
Not Included ................................................................1-2
Model Differences .......................................................1-3
System Software ..........................................................1-4
System Startup ...............................................................1-5
System Map: LCD Panel Open ......................................1-6
LED Indicators ................................................. .... ..........1-7
Hot Key Buttons & Keyboard .......................................1-8
System Map: Front View (Audio "DJ") ......................1-10
Audio "DJ" CD Player ................................................. 1-11
Storage Devices, Mouse, Audio &
Printer
Overview ........................................................................2-1
Hard Disk Drive .............................................................2-2
Optical Device ...............................................................2-3
Loading Discs ..............................................................2-3
Handling CDs or DVDs ...............................................2-4
DVD Regional Codes ..................................................2-5
7-in-1 Card Reader .........................................................2-6
ExpressCard Slot ............................................................2-7
Inserting and Removing ExpressCards ........................2-7
Application Hot Key ......................................................2-8
TouchPad and Buttons/Mouse .......................................2-9
Audio Features .............................................................2-10
XIII
Preface
Configuring the Infrared Settings for FIR ...................2-11
Adding a Printer ...........................................................2-12
USB Printer ...............................................................2-12
Install Instructions: ...................................................2-12
Parallel Printer ...........................................................2-12
Power Management
Overview ........................................................................3-1
The Power Sources ........................................................3-2
AC/DC Adapter ................................................. .... .... ..3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Plans ...................................................................3-4
System Power Options ...................................................3-6
Hibernate vs. Shutdown ...............................................3-6
Stand by Mode vs. Hibernate Mode ............................3-6
Sleep ...........................................................................3-7
Hibernate ....................................................................3-7
Configuring the Power Button .......................................3-8
Battery Information .......................................................3-9
Battery Power .............................................................3-9
Conserving Battery Power ...........................................3-10
Battery Life .............................................................. ....3-11
New Battery ..............................................................3-11
Recharging the Battery with the AC/DC Adapter .....3-11
Proper handling of the Battery Pack .........................3-12
Battery FAQ ..............................................................3-13
Drivers & Utilities
RAID Setup .................................................................4-1
What to Install ............................................................... .4-1
Module Driver Installation ..........................................4-1
Driver Installation ..........................................................4-2
Manual Driver Installation .........................................4-3
Updating/Reinstalling Individual Drivers ...................4-4
User Account Control (Win Vista) ..............................4-4
Windows Security Message .........................................4-4
New Hardware Found ..................................................4-4
Driver Installation Procedure .......................................4-5
Chipset ........................................................................ 4-5
Video (VGA) ..............................................................4-5
Audio ..........................................................................4-5
Modem ........................................................................ 4-5
LAN ............................................................................4-5
TouchPad .................................................................... 4-6
Card Reader/ExpressCard ..........................................4-6
Hot Key Utility ...........................................................4-6
Optional Drivers ..........................................................4-6
Wireless LAN .............................................................4-7
PC Camera ..................................................................4-7
XIV
Preface
Bluetooth ....................................................................4-7
TV Tuner ....................................................................4-7
BIOS Utilities
Overview ........................................................................5-1
The Power-On Self Test (POST) ................................... 5-2
Failing the POST .........................................................5-3
Fatal Errors .................................................................5-3
Non-Fatal Errors .........................................................5-3
The Setup Program ........................................................5-4
Entering Setup .............................................................5-4
Setup Screens ......................................................... ......5-5
Main Menu .....................................................................5-6
System Time & Date (Main Menu) ...............................5-6
IDE Channel 0/1 Master/Slave (Main Menu) ................5-7
Installed Memory (Main Menu) ....................................5-7
Advanced Menu .............................................................5-8
Advanced Chipset Control (Advanced Menu) ..............5-9
National 381 SIO Control
Sub-Menu (Advanced Menu) ......................................5-10
Reset Configuration Data: (Advanced Menu) .............5-10
Legacy USB Support: (Advanced Menu) ....................5-10
Boot-time Diagnostic Screen: (Advanced Menu) ........5-10
Power On Boot Beep: (Advanced Menu) ....................5-10
Battery Low Alarm Beep: (Advanced Menu) .............5-10
Security Menu ..............................................................5-11
Set Supervisor Password (Security Menu) ..................5-11
Password on boot: (Security Menu) .............................5-12
Boot Menu ...................................................................5-13
Exit Menu ....................................................................5-14
Upgrading The Computer
Overview ........................................................................6-1
When Not to Upgrade ..................................................6-2
Removing the Battery ....................................................6-3
Upgrading the Hard Disk Drive(s) .................................6-4
Upgrading the System Memory (RAM) ........................6-6
Upgrading the Optical (CD/DVD) Device(s) ................6-9
Modules
Overview ........................................................................7-1
Wireless LAN Module ...................................................7-2
Intel WLAN Driver Installation .................................7-2
802.11 b/g WLAN Driver Installation ........................7-2
Connecting to a Wireless Network .............................. 7-3
Windows Mobility Center ...........................................7-6
PC Camera Module ........................................................7-7
PC Camera Driver Installation ...................................7-7
PC Camera Audio Setup ..............................................7-8
BisonCap ...................................................................7-10
XV
Preface
Eliminating Screen Flicker .......................................7-11
Bluetooth Module .................................................... ....7-12
Bluetooth Driver Installation ....................................7-12
Mini-PCI TV Tuner Module ........................................7-14
YUAN PVR Mini-PCI MPC622 TV Tuner Module .7-15
Installing the MPC622-64 Driver .............................7-15
Setting Up SATA RAID ..............................................7-16
Troubleshooting
Overview ........................................................................8-1
Basic Hints and Tips ......................................................8-2
Backup and General Maintenance .................................8-3
Viruses ........................................................................... 8-4
Upgrading and Adding New Hardware/Software ..........8-5
Problems & Possible Solutions ......................................8-7
Interface (Ports & Jacks)
Overview .......................................................................A-1
Ports and Jacks ..............................................................A-2
Card Reader ..................................................................A-2
TV Antenna Jack ......................................... .... .... .........A-2
Consumer Infrared Transceiver ....................................A-2
DC-In Jack ....................................................................A-2
DVI-Out Port ................................................................A-2
Headphone-Out Jack .....................................................A-3
Infrared (FIR) Transceiver ............................................A-3
Line-In Jack ..................................................................A-3
Microphone-In Jack ......................................................A-3
Mini-IEEE 1394 Port ....................................................A-3
RJ-11 Phone Jack ..........................................................A-4
RJ-45 LAN Jack ............................................................A-4
S/PDIF-Out Jack ...........................................................A-4
Security Lock Slot ........................................................A-4
Serial Port .....................................................................A-4
7-Pin S-Video-Out Jack ................................................A-4
USB 2.0/1.1 Ports .........................................................A-5
NVIDIA Video Driver Controls
NVIDIA Video Driver Installation ...............................B-1
NVIDIA Control Panel .................................................B-2
Display Devices ............................................................B-5
Attaching Other Displays ..............................................B-6
Display Modes ..............................................................B-8
Enabling TV Display ..................................................B-11
Changing the TV Signal Format ...............................B-12
Specifications 1
Processor Types ............................................................C-2
Core Logic ....................................................................C-2
LCD ..............................................................................C-2
XVI
Preface
Security ......................................................................... C-2
Memory .........................................................................C-2
BIOS ............................................................................. C-2
Video Card Options ...................................................... C-3
Storage Options ............................................................C-4
Audio ............................................................................ C-4
Keyboard & Pointing Device ........................................C-4
I/O Ports ........................................................................C-5
Communication ............................................................. C-5
Operating Systems Supported .......................................C -6
Power Management ......................................................C-6
Power ............................................................................ C-6
Environmental Spec ......................................................C-6
Physical Dimensions & Weight .................................... C-6
Optional ........................................................................ C-7
Windows XP Information
DVD Regional Codes ...................................................D-2
Windows XP Start Menu & Control Panel ...................D-3
Audio Features ..............................................................D-4
Video Features ..............................................................D-5
Display Properties .........................................................D-6
Display Devices & Options...........................................D-7
Display Modes...............................................................D-8
Attaching Other Displays (for NVIDIA VGA).............D-9
To Enable Extended Desktop (for NVIDIA VGA).....D-11
Attaching Other Displays (for ATI VGA)...................D-12
Power Management Features ......................................D-13
Power Schemes ...........................................................D-13
System Power Options.................................................D-14
Hibernate Mode vs. Shutdown ....................................D-14
Stand by Mode vs. Hibernate Mode ............................D-14
Stand by ......................................................................D-15
Hibernate .....................................................................D-15
Configuring the Power Button ....................................D-16
Battery Information .....................................................D-17
New Battery ................................................................D-17
Battery Life .................................................................D-17
Recharging the Battery with the AC/DC Adapter .......D-18
Proper handling of the Battery Pack ...........................D-19
Battery FAQ.................................................................D-20
Driver Installation .......................................................D-21
What to Install .............................................................D-22
Updating/Reinstalling Individual Drivers....................D-23
Chipset ........................................................................D-24
Video (for ATI) ...........................................................D-24
Video (for NVIDIA) ...................................................D-24
Audio ..........................................................................D-24
Modem ........................................................................D-25
LAN ............................................................................D-25
XVII
Preface
TouchPad .................................................................... D-26
Card Reader/ExpressCard ...........................................D-26
Hot Key Utility ...........................................................D-26
AutoMail Checker ......................................................D-27
Module Drivers............................................................D-27
PC Camera Driver Installation ....................................D-28
Intel WLAN Driver Installation ..................................D-29
802.11 b/g WLAN Driver Installation ........................D-30
Bluetooth Driver Installation ......................................D-31
Mini-PCI TV Tuner Module .......................................D-32
Installing the LifeView FlyDVB-T Driver..................D-32
Installing the MPC622-MCE Driver ...........................D-33
Installing the MPC788 Driver &
Cyberlink PowerCinema..............................................D-33
Setting Up SATA RAID .............................................D-34
XVIII
Quick Start Guide
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard/34/54), Application Hot Key, TouchPad &
Mouse, Audio Features, FIR Settings & Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, PC Camera, TV Tuner and RAID
modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the NVIDIA Video driver controls.
• Appendix C The computer’s specification.
• Appendix D Information on the Window’s XP OS.
1
Overview 1 - 1
1
Quick Start Guide
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “Drivers & Utilities” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer”
on page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in this Quick Start Guide should be enough to get you up
and running. Eventually you should try to look through all the documentation (more
detailed descriptions of the functions, setup and system controls are covered in the
remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You
may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Not Included
Operating Systems (e.g. Windows Vista/ Windows XP etc.) and applications (e.g. word processing, spreadsheet
and database programs) have their own manuals, so please consult the appropriate manuals.
1 - 2 Overview
Quick Start Guide
Model Differences
This notebook series includes two different design types, however only one design is pictured in this manual.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the appropriate drivers. Drivers are programs which act as an interface between the computer and a hardware component
e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4
- 3. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your
system hasn’t been properly configured (your service representative may have already done that for you), refer to “Drivers
& Utilities” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.
1
Overview 1 - 3
1
Quick Start Guide
System Software
TV Tuner Module
Support
Note that the TV Tuner
module (factory) options
in Windows Vista are
supported by the Win-
dows Media Center
software which comes
built-in to the Windows
Vista Home Premium
and Ultimate Editions
only.
If your purchase includes a TV Tuner option, and you are reconfiguring your system
for a different system,
you should install either
Windows Home Premium or Ultimate Edi-
tions only.
Your computer may already come with system software pre-installed. Where this is
not the case, or where you are re-configuring your computer for a different system,
you will find the following operating systems are supported:
Operating System & Version Note
*Windows XP (Home or Professional)
*Windows XP Media Center Edition
Windows Vista (64-bit) Home Basic Edition
Windows Vista (64-bit) Home Premium Edition
Windows Vista (64-bit)
Business/Enterprise/Ultimate Editions
In order to run Windows Vista
without limitations or decreased
performance, your computer requires
a minimum 1GB of system memory
(RAM).
Table 1 - 1 - Operating Systems Supported
*Note: For information on the Windows XP OS (specifically power, video and driver
information) see “Windows XP Information” on page D - 1.
1 - 4 Overview
Quick Start Guide
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter.
5. Move the LCD latches at the front of the computer outwards towards the sides of the computer, and hold the
right latch in place to release the top cover.
6. Raise the lid/LCD to a comfortable viewing angle, and press the power button (make sure the Audio "DJ"
player is turned off) to turn the computer “on”.
7. Adjust the LCD panel to a comfortable viewing angle.
8. The LED indicators show the power and battery status of the computer and di splay information on the power
status of the PC Camera, Bluetooth and Wireless LAN modules.
Shutdown
Note that you should always shut your computer
down by choosing the Shut Down command from
the Lock Button Menu in Windows Vista. This
will help prevent hard disk or system problems.
1
Figure 1 - 1 - Computer With AC/DC Adapter Plugged In
System Startup 1 - 5
1
Quick Start Guide
System Map: LCD Panel Open
Figure 1 - 2
Front View
LCD Panel Open
1. Optional Built-In PC Camera
2. LCD
3. Hot Key Buttons
4. Power Button
5. Keyboard
6. TouchPad and Buttons
7. Audio "DJ" Controls
8. Built-In Microphone
9. Audio "DJ" LED Display Panel
(Including LED Indicators)
Audio "DJ" & Power
Button
Make sure that the Audio "DJ"
player is off before pressing the
power button to turn the computer on.
1
Wireless Device
Operation Aboard
2
3
4
5
6
7
9
8
7
Aircraft
The use of any portable
electronic transmission
devices (e.g. WLAN or
Bluetooth) aboard aircraft
is usually prohibited.
Make sure any wireless
modules are OFF if you
are using the computer
aboard aircraft.
Use the appropriate function key combination (see
Table 1 - 4, on page 1 -
9) to toggle power to any
wireless modules, and
check the LED indicators
to see if any modules are
powered on or not (see
Table 1 - 2, on page 1 -
7).
1 - 6 System Map: LCD Panel Open
Quick Start Guide
1
LED Indicators
The LED indicators on the computer display helpful
information about the current status of the computer.
Icon Color Description
Green The Computer is On
Blinking
Green
Green The AC/DC Adapter is Plugged In
Green Number Lock is Activated
Green Caps Lock is Activated
Green Scroll Lock is Activated
The Computer is In Stand by Mode
Icon Color Description
Orange The Battery is Charging
Blinking
Orange
Green The Battery is Fully Charged
Green Hard Disk Activity
Green
Green The Bluetooth Module is Powered On
Green The WLAN Module is Powered On
Blinking
Amber
The Battery has Reached Critically
Low Power Status
Second Battery Indicator
(Colors Displayed as Above)
The PC Camera Module is Powered
On
New Mail Has Arrived
Table 1 - 2 - LED indicators
LED Indicators 1 - 7
1
Quick Start Guide
Hot Key Buttons & Keyboard
These buttons give instant access to the default Internet browser and e-mail program, and to a user-defined
application, with one quick button press. To use the
“user-defined application Hot Key Button”, you must
install the driver (see “Hot Key Utility” on page 4 - 6).
See “Application Hot Key” on page 2 - 8 for configu-
ration instructions.
Table 1 - 3 - Hot Key Buttons
Hot Key Function
Activate the Default E-Mail Browser
Activate the Default Internet Program
Activate the user specified application e.g.
Microsoft Word or Excel
The keyboard has a numerical keypad for easy numeric data input, and features Function Keys to allow you
to change operational features instantly.
Activate the Number Lock feature by pressing the
Num Lk key at the top right of the keyboard. You may
check if Number Lock is enabled or not by looking at
the LED status indicators.
1 - 8 Hot Key Buttons & Keyboard
Keys Description
Quick Start Guide
1
Fn + ~
Fn + F1 TouchPad Toggle
Fn + F2 Fan Automatic Control / Full Power
Fn + F3 Mute Toggle
Fn + F4 Sleep Toggle
Fn + F5 Decrease Audio Volume
Fn + F6 Increase Audio Volume
Fn + F7 Display Toggle
Fn + F8 Decrease LCD Brightness
Fn + F9 Increase LCD Brightness
Fn + F10 PC Camera Toggle
Fn + F11 WLAN Module Toggle
Fn + F12 Bluetooth Module Toggle
Fn + Scr Lk Scroll Lock Toggle
Play/Pause
(in Audio/Video Programs)
Table 1 - 4 - Function Keys
Figure 1 - 3 - Keyboard
Function Keys
Num Lk & Scr Lk Keys
Numeric
Keypad
Fn Key
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use
any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
Hot Key Buttons & Keyboard 1 - 9
1
Quick Start Guide
System Map: Front View (Audio "DJ")
1 2 3 4 5 6 7 8 9
11
10
Figure 1 - 4 - Front View (Audio "DJ")
1. Audio "DJ" Power Button
2. Volume Down
3. Volume Up
4. Repeat
5. LED Display
6. Previous Track
7. Next Track
8. Play/Pause
9. Stop (Press Twice To Eject The CD/DVD)
10. Repeat Mode Indicator
11. Track Indicator
12. Time Indicator
13. Disc Indicator
1 - 10 System Map: Front View (Audio "DJ")
12 13
Audio "DJ" MP3 Track Limit
There is a track limit of 256 tracks on any MP3 CD/
DVD. This means that only the first 256 tracks may
be played on any MP3 CD/DVD.
Audio "DJ" & Power Button
Make sure that the Audio "DJ" player is off before
pressing the power button to turn the computer on.
Audio "DJ" CD Player
The built-in standalone audio CD player gives direct
hardware control for audio CDs/DVDs when the computer is shut down, but has a working power source.
1. Make sure that the computer is shut down (i.e. the
operating system is not running) but you have a
working power source (either battery or AC Power).
2. Press the Audio "DJ" power button.
3. Press the open button on your CD/DVD device (or
press the stop button twice) and carefully place
an audio CD onto the disc tray with label-side fa cing
up (DVD drives will also play audio CDs).
4. Gently push the CD/DVD tray in until its lock “clicks”
and you are ready to start.
5. The Disc Indicator will flash while data is being
accessed.
6. The LED will display the number of tracks.
7. Press the play/pause button to start the CD/DVD.
8. Control the CD/DVD tracking and volume from the
control panel.
9. Use the stop button to stop the disc, or press it
twice to eject the disk.
10. Press the power button again to turn the player off.
9
Quick Start Guide
TV Tuner Option
If you have included the optional TV Tuner in your
purchase configuration, you can use the supplied remote control unit to control the Audio "DJ".
Disk Eject Warning
Don’t try to eject a CD/DVD while the system is accessing it. This may cause the system to “crash”. Stop
the disk first then eject it, or press the stop button
twice.
1
Audio "DJ" CD Player 1 - 11
1
Quick Start Guide
System Map: Rear View
1
Figure 1 - 5 - Rear View
1. Vent/Fan Intake/Outlet
2. S/PDIF-Out Jack
3. Line-In Jack
4. 2 * USB 2.0 Ports
5. DVI-Out Port
6. TV Antenna Jack (Enabled With TV Tuner Only)
7. RJ-11 Phone Jack
8. RJ-45 LAN Jack
9. 7-Pin S-Video-Out Jack
10. DC-In Jack
11. Serial Port
243
1 - 12 System Map: Rear View
5
7 8
6
9
10 11
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake/Outlet while the computer is in
use.
USB Ports
Note that the connections to the USB ports only fit one way,
do not force them.
System Map: Right View
4
1 2 3
5 6
Mini-IEEE 1394 Port
Quick Start Guide
Figure 1 - 6 - Right View
1. Headphone-Out Jack
7
2. Microphone-In Jack
3. 7-in-1 Card Reader
4. Express Card Slot
5. Mini-IEEE 1394 Port
6. 2 * USB 2.0 Ports
7. Speaker
1
Both Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices.
ExpressCard Slot
The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
7-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) /
MS Pro (Memory Stick Pro) / MS Duo (requires PC adapter) /
Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
System Map: Right View 1 - 13
USB Ports
Note that the connections to
the USB ports only fit one
way, do not force them.
1
Quick Start Guide
System Map: Left View
Figure 1 - 7 - Left View
1. Security Lock Slot
2. Speaker
3. Optional Device Drive Bay
(for CD/DVD Device,
see page 2 - 3, or 2nd SATA
Hard Disk, or 2nd Battery)
Changing DVD Regional Codes
Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/
CD-ROM drives. Double-click on the DVD-ROM device to
bring up the Properties dialogue box, and select the DVD
Region (tab) to bring up the control panel to allow you to
adjust the regional code (see “DVD Regional Codes” on
page 2 - 5).
DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times.
The fifth selection is permanent. This cannot be altered
even if you change your operating system or you use the
module in another computer.
2
3
1
2nd Battery Notes
Note that the 2nd battery is designed to optimize and boost the
power performance of the system.
The system WILL NOT boot up from the 2nd battery alone. Use
either the AC/DC adapter or main battery to boot up the system.
The system DOES NOT support the Hot Swap function. Save
your work and shut the system down before swapping batteries.
The 2nd battery alone CAN NOT power the system if the NVIDIA
GeForce Go 7900 GTX video card is the installed option.
CD/DVD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened
paper clip into the emergency eject hole. Do not use a sharpened
pencil or any object that may break and become lodged in the
hole. Don’t try to remove a floppy disk/CD/DVD while the system
is accessing it. This may cause the system to “crash”.
1 - 14 System Map: Left View
System Map: Bottom View
6
1
1
4
3
Quick Start Guide
Figure 1 - 8 - Bottom View
1. Vent/Fan Intake/Outlet
2. Battery
2
3. Optical Device Release Latches
4. Video Card / HDD / RAM Bay Cover
5. Infrared & Consumer Infrared Transceiver
6. Sub Woofer
1
5
3
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery
at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 9 for full instruc-
tions.
System Map: Bottom View 1 - 15
1
Quick Start Guide
Windows Vista Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can cu stomize the look of
the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Click here to toggle Category View
Figure 1 - 9 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea-
tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed
in Table 4 - 1, on page 4 - 3. To see all controls it may be necessary to toggle off Category View.
1 - 16 Windows Vista Start Menu & Control Panel
Quick Start Guide
Video Features
This computer features different PCI Express video cards, depending on your purchase option (see “Video Card
Options” on page C - 3). You can configure display options, from the Display Settings control panel in Win-
dows as long as the appropriate video driver is installed. For more detailed video information see “NVIDIA
Video Driver Installation” on page B - 1.
To access Display Settings in Windows:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click
Personalization > Display Settings).
3. Move the slider to the preferred setting in Resolution: (Figure 1 - 10 on page 1 - 18).
4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 10 on page 1 - 18).
5. Click Advanced Settings (button) (Figure 1 - 10 on page 1 - 18).
6. Click GeForce Go..... (tab).
7. Click Start the NVIDIA Control Panel (Figure 1 - 10 on page 1 - 18) to access the control panel.
8. The NVIDIA Control Panel can also be accessed by right-clicking the desktop, and then clicking NVIDIA
Control Panel.
3
4
1
2
1
Video Features 1 - 17
1
Quick Start Guide
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display (connected to the DVI-Out port) or TV (connected to the S-Video-Out jack) as your display device.
Video Card Options
Note that card types, specifications and drivers are
subject to continual up-
1
2
4
3
Figure 1 - 10 - Display Settings
NVIDIA Display Mode Description
Single One display device is used.
Clone Both connected displays output the same view
dates and changes. Check
with your service center for
the latest details on video
cards supported.
Dualview Both connected displays are treated as separate devices, and act as a virtual desktop
Table 1 - 5 - Display Modes Available
1 - 18 Video Features
Quick Start Guide
Power Options
The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16 ) allows you
to configure power management features for your computer. You can conserve power by means of power plans
and configure the options for the power button, sleep button, computer lid (when closed), display and sleep
mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to
create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con-
figuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 9.
1
Note: Sleep is the default power saving state in Windows Vista
Figure 1 - 11 - Power Options
Power Options 1 - 19
1
Quick Start Guide
1 - 20
Storage Devices, Mouse, Audio & Printer
Chapter 2: Storage Devices, Mouse, Audio & Printer
Overview
Read this chapter to learn more about the following main features and components
of the computer:
•Hard Disk Drive
• Optical Device
• 7-in-1 Card Reader
• ExpressCard Slot
• Application Hot Key
• TouchPad and Buttons/Mouse
• Audio Features
• Configuring the Infrared Settings for FIR
• Adding a Printer
2
Overview 2 - 1
Storage Devices, Mouse, Audio & Printer
2
Before attempting to access any of the internal
components of your
computer please ensure
that the machine is not
connected to the AC
power, and that the machine is turned off. Also
ensure that all peripheral cables, including
phone lines, are disconnected from the computer.
Power Safety
Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk can be
taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height
of 9.5 mm. The hard disk is accessible from the bottom of your computer as seen
below. Further details on removing and inserting the hard disk are available in “Up-
grading the Hard Disk Drive(s)” on page 6 - 4.
1
1
Figure 2 - 1
Hard Disk Location
2 - 2 Hard Disk Drive
Storage Devices, Mouse, Audio & Printer
Optical Device
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the model you purchased (see “Storage Options” on page C -
4). The optical device is usually labeled “Drive D:” and may be used as a boot de-
vice if properly set in the BIOS (see “Boot Menu” on page 5 - 13).
Loading Discs
To insert a CD/DVD, press the open button and carefully place a CD/DVD onto
the disc tray with label-side facing up (use just enough force for the disc to click onto
the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you
are ready to start. The busy indicator will light up while data is being accessed,
or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole
3
to open the tray.
2 3
1
2
1
Sound Volume
Adjustment
How high the sound volume can be set depends
on the setting of the volume control within Win-
dows. Click the Volume
icon on the taskbar to
check the setting.
Peripherals must be
connected before you
turn on the system.
Figure 2 - 2
Optical Device
2
Optical Device 2 - 3
Storage Devices, Mouse, Audio & Printer
2
CD Emergency Eject
If you need to manually
eject a CD (e.g. due to
an unexpected power
interruption) you may
push the end of a
straightened paper clip
into the emergency eject
hole. However please
do NOT use a sharpened pencil or similar
object that may break
and become lodged in
the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the system is accessing it. This
may cause the system
to “crash”.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please
follow the advice below to make sure that the data stored on your CDs/DVDs can be
accessed.
Note the following:
• Hold the CD or DVD by the edges; do not touch the surface of the disc.
• Use a clean, soft, dry cloth to remove dust or fingerprints.
• Do not write on the surface with a pen.
• Do not attach paper or other materials to the surface of the disc.
• Do not store or place the CD or DVD in high-temperature areas.
• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
• Do not bend the CD or DVD.
• Do not drop or subject the CD or DVD to shock.
Handling CDs or DVDs
2 - 4 Optical Device
Storage Devices, Mouse, Audio & Printer
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 14.
.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2
3
4
5
6China
Western Europe, Japan, South
Africa, Middle East & Egypt
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
South & Central America, Mexico,
Australia, New Zealand
N Korea, Russia, Eastern Europe,
India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Figure 2 - 3
DVD Regions
Optical Device 2 - 5
Storage Devices, Mouse, Audio & Printer
2
Card Reader Cover
Make sure you keep the
cover in the card reader
when not in use. This
will help prevent foreign
objects and/or dust getting in to the card reader.
7-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push the
card into the slot and it will appear as a removable device, and can be accessed in
the same way as your hard disk (s). Make sure you install the Card Reader driver
(see “Card Reader/ExpressCard” on page 4 - 6).
• MMC (MultiMedia Card)
• SD (Secure Digital)
• MS (Memory Stick)
• MS (Memory Stick Pro)
• MS Duo (requires PC adapter*)
• Mini SD (requires PC adapter*)
• RS MMC (requires PC adapter*)
*Note: The PC adapters are usually supplied with these cards.
Figure 2 - 4
Left & Front Views
1. Card Reader
1
2 - 6 7-in-1 Card Reader
Storage Devices, Mouse, Audio & Printer
ExpressCard Slot
The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/
34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC
Cards).
ExpressCard/54 is used for applications which require a larger interface slot, e.g.
CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the ExpressCard driver (see “Card Reader/ExpressCard” on page 4 - 6).
Inserting and Removing ExpressCards
• Align the ExpressCard with the slot and push it in until it locks into place.
• To remove an ExpressCard, simply press the card to eject it.
ExpressCard
Slot Cover
Make sure you keep the
cover in the ExpressCard slot when not in
use. This will help prevent foreign objects and/
or dust getting in to the
ExpressCard Slot.
Figure 2 - 5
ExpressCard Slot
2
ExpressCard Slot 2 - 7
Storage Devices, Mouse, Audio & Printer
2
Application Hot Key
The hot key button gives instant access to a user-defined application, with one quick
Application.exe
You will need to locate
the actual application
executable (.exe) file,
not just the shortcut.
To find the application
right-click its shortcut
on the desktop and
click Properties. Click
the shortcut (tab) an d
see where the executable file is located by
clicking the Open File
Location (button).
button press. To configure a program to open when the application hot key is
pressed, install the driver (see “Hot Key Utility” on page 4 - 6), and then follow the
instructions below.
1. Right click the Hot Key driver icon in the taskbar.
2. Select Setup from the menu, scroll to Application 1 and click to select Custom.
3. An Open dialog box will appear on the screen.
Figure 2 - 6
Hot Key
Configuration
Screens
4. Browse to the directory where the desired application.exe (see the sidebar)
program exists.
5. Double-Click on the program file or choose Open.
2 - 8 Application Hot Key
Storage Devices, Mouse, Audio & Printer
TouchPad and Buttons/Mouse
The TouchPad is an alternative to the mouse; however, you can also add a mouse to
your computer through one of the USB ports. The TouchPad buttons function in
much the same way as a two-button mouse. The central button may be configured to
function as you require.
Install the TouchPad driver (see page 4 - 6) and then double-click the TouchPad
driver icon in the taskbar to configure the functions. You may then configure the
TouchPad tapping, buttons, scrolling, pointer motion and sensitivity options to your
preferences. The TouchPad may be toggled on/off by means of the Fn + F1 key
combination. You will have one of two TouchPad options as pictured below.
Mouse Driver
If you are using an external mouse your operating system may be able
to auto-configure your
mouse during its installation or only enable its
basic functions. Be sure
to check the device’s
user documentation for
details.
Figure 2 - 7
Mouse Properties
2
TouchPad and Buttons/Mouse 2 - 9
Storage Devices, Mouse, Audio & Printer
2
Audio Features
You can configure the audio options on your computer from the Sound control
Sound Volume
Adjustment
The sound volume level
is set using the volume
control within Windows
(and the volume function keys on the computer). Click the volume
icon in the taskbar to
check the setting.
panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/
control panel (right-click the taskbar icon to bring up an audio menu). The volume
may also be adjusted by means of the Fn + F5/F6 key combination.
Right-click the icon
to access the menu
above.
Figure 2 - 8
Realtek Audio
Manager
2 - 10 Audio Features
Storage Devices, Mouse, Audio & Printer
Configuring the Infrared Settings for FIR
To configure your computer’s infrared port (on the right of the computer) for Far Infrared (FIR) communication follow these steps:
1. Click Start, and click Control Panel (or point to Settings and click Control
Panel).
2. Double-click Infrared (Network and Internet Category) icon.
3. Click Hardware (tab), and click the Properties button.
4. Click the Change settings button and click Advanced (tab).
5. Select “Infrared Transceiver A” and change the Value to “HP HSDL-2300/
3600”.
6. Click OK > OK.
7. Restart the computer i f prompted to do so.
You can enable/disable the infrared transceiver in the BIOS (see “National 381 SIO
Control Sub-Menu (Advanced Menu)” on page 5 - 10). For further information,
please refer to the manual of the device you wish to connect.
Infrared
Communication
The infrared transceiver
operates on a “Line of
Sight”.
Make sure nothing is
blocking the “Line of
Sight” between your
system’s transceiver
and the destination’s
transceiver.
2
Configuring the Infrared Settings for FIR 2 - 11
Storage Devices, Mouse, Audio & Printer
2
After setting up the printer attach the parallel cable to the printer.
Connect the printer’s
parallel cable to the Parallel to USB converter,
and then plug the converter into the USB port.
Turn ON the printer,
then turn ON the computer.
Windows will identify the
printer and either load
one of its own drivers or
ask you to supply one.
Follow the on-screen instructions.
Parallel Printer
Adding a Printer
The most commonly used peripheral is a printer. The following conventions will
help you to add a printer; however it is always best to refer to the printer manual for
specific instructions and configuration options.
USB Printer
Most new printers have a USB interface connection. You may use any one of the
ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instructions (unp acking, p aper tray, toner/ink cartridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you
to supply one. Follow the on-screen instructions.
Parallel Printer
This is still a very common type of printer. The install instructions are in the sidebar
(you will need to purchase a parallel to USB converter).
2 - 12 Adding a Printer
Power Management
Chapter 3: Power Management
Overview
To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer
(the monitor and hard disk drive) or the whole system.
This chapter covers:
• The Power Sources
• Turning on the Computer
• Power Plans
• System Power Options
• Configuring the Power Button
• Battery Information
The computer uses enhanced power saving techniques to give the operating system
(OS) direct control over the power and thermal states of devices and processors. For
example, this enables the OS to set devices into low-power states based on user settings and information from applications.
OS Note
Power management
functions will vary slightly depending on your
operating system. For
more information it is
best to refer to the user’s
manual of your operating system.
(Note: All pictures used
on the following pages
are from the Windows
Vista OS.)
3
Overview 3 - 1
Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
3
AC/DC Adapter
Use only the AC/DC adapter that comes with your computer. The wrong type of AC/
DC adapter will damage the computer and its components (see page C - 6).
1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the
AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.
Battery
The battery allows you to use your computer while you are on the road or when an
electrical outlet is unavailable. Battery life varies depending on the applications and
the configuration you're using. To increase battery life, let the battery discharge
completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 13).
We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 9.
3 - 2 The Power Sources
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.
When the computer is on, you can use the power button as a Sleep/Hibernate hot key
button when it is pressed for less than 4 seconds (pressing and holding the power
button for longer than this will shut the computer down). Use Power Options
(Hardware and Sound menu) control panel in Windows Vista to configure this feature.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the power button for 4 seconds, or longer, to force the system to turn itself off.
Power Button Sleep
Sleep is the default power mode when the power button is pressed for less than 4 seconds.
You may configure the options for the power button from the Power Options (Hardware
and Sound menu) control panel in Windows Vista (see your OS’s documentation, or
“Configuring the Power Button” on page 3 - 8 for details).
Power Management
Shut Down
Note that you should always shut your computer down by choosing the
Shut Down command
from the Lock Button
Menu in Windows Vis-
ta. This will help prevent
hard disk or system
problems.
3
Turning on the Computer 3 - 3
Power Management
Power Plans
3
Resuming
Operation
If the display is off the
system can resume by
pressing any key on the
keyboard.
The system can resume
from Sleep mode by
pressing the Sleep But-
ton key combination (Fn
+ F4), or power button.
Password
It is recommended that
you enable a password
on system resume in order to protect your data.
The computer can be configured to conserve power by means of power plans. You
can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and
to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to access further configuration options in Advanced Settings.
Figure 3 - 1
Power Plan
Advanced Settings
3 - 4 Power Plans
Each Windows Power Plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing
any reduced performance (especially under DC/battery power).
Choose High performance for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this
scheme may slow down the overall performance of the computer in order to save
power) for maximum power saving when the computer is battery (DC power) powered.
Power Management
3
Figure 3 - 2
Power Plans
Power Plans3-5
Power Management
System Power Options
3
Sleep Button
The Sleep Button
in the Start Menu (not
available in Classic
View) can be used to
send the computer into
Sleep.
Note that Sleep is the
default power saving
state in Windows Vista.
You can use the system power options to stop the computer’s operation and restart
where you left off. The system features Sleep and Hibernate power saving states
(Hibernate will need to be enabled from power plan Advanced Settings see Figure
3 - 1 on page 3 - 4).
Hibernate vs. Shutdown
Hibernate mode and Shutdown are the same in that the system is off and you need
to press the power button to turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left off
(what was on your desktop) without reopening the application(s) and file(s) you last
used.
You can use either method depending on your needs.
Stand by Mode vs. Hibernate Mode
If you want to stay away from your work for just a while, you can put the system on
Stand by instead of in hibernation. It takes a longer time to wake up the system from
Hibernate mode than from Stand by mode. Sleep will effectively act as Hibernate
if the computer battery becomes depleted (see “Sleep Mode & Mobile PC Battery”
on page 3 - 7).
3 - 6 System Power Options
Sleep
Stand by saves the least amount of power, but takes the shortest time to return to full
operation. During Stand by the hard disk is turned off, and the CPU is made to idle
at its slowest speed. All open applications are retained in memory. When you are not
using your computer for a certain length of time, which you specify in the operating
system, it will enter Stand by mode to save power.
Hibernate
Hibernate uses no power and saves all of your information on a part of the hard disk
before it turns the system off. Although it saves the most power it takes the longest
time to return to full operation. You can set your computer to automatically enter Hi-
bernate when the battery power is almost depleted. You will need to enable Hibernate mode from the Advanced Settings in power plans, or you put the system
directly into Hibernate mode from the Lock Button Menu. The system will resume from Hibernate mode by pressing the power button.
Power Management
Sleep Mode &
Mobile PC Battery
A mobile PC in Sleep
uses very little battery
power.
After an extended period of time the computer
will save any open documents and applications
to hard disk.
Figure 3 - 3
Lock Button Menu
3
System Power Options 3 - 7
Power Management
Configuring the Power Button
3
Password
Protection
It is recommended that
you enable a password
on wake up in order to
protect your data.
However you can disable this setting from the
Power Options menu
by clicking Require a
password on wakeup
in the left menu, and selecting the options (click
Change settings that
are currently unavailable).
Figure 3 - 4
Power Options
Define Power
Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the
computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In
Hibernate the LED will be off (battery) or orange (AC/DC adapter). If only the display is turned off, the LED will remain green.
3 - 8 Configuring the Power Button
Battery Information
Please follow these simple guidelines to get the best use out of your battery.
Battery Power
Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be
taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from
power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).
Click the battery icon in the taskbar to see the current battery level and charge
status.
Power Management
Low Battery
Warning
When the battery is critically low, immediately
connect the AC/DC
adapter to the computer
or save your work, otherwise, the unsaved
data will be lost when
the power is depleted.
Figure 3 - 5
Battery Icon
(Taskbar) & Battery
Advanced Settings
3
Battery Information 3 - 9
Power Management
Conserving Battery Power
3
Windows Mobility
Center
The Windows Mobility
Center control panel pro-
vides an easy point of access for information on
battery status, power plans
used and wireless device
status etc.
Figure 3 - 6
Windows Mobility
Center
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
• Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
• Reduce the amount of time before the display is turned off.
• Close wireless, Bluetooth, modem or communication applications when they are
not being used.
• Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
3 - 10 Conserving Battery Power
Battery Life
Battery life may be shortened through improper maintenance. To optimize the life
and improve its performance, fully discharge and recharge the battery at least
once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery” on page 6 - 3.
New Battery
Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 13 for instructions on how to do this).
Recharging the Battery with the AC/DC Adapter
The battery pack automatically recharges when the AC/DC adapter is attached and
plugged into an electrical outlet. If the computer is powered on, and in use, it will
take several hours to fully recharge the battery. When the computer is turned off but
plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 7 for information on the battery charge status, and to “Battery Information” on page 3 - 9 for more information on how to maintain and properly
recharge the battery pack.)
Power Management
3
Battery Life3-11
Power Management
Proper handling of the Battery Pack
3
Caution
Danger of explosion if
battery is incorrectly replaced.
• DO NOT disassemble the battery pack under any circumstances
• DO NOT expose the battery to fire or high temperatures, it may explode
• DO NOT connect the metal terminals (+, -) to each other
Replace only with the
same or equivalent type
recommended by the
manufacturer. Discard
used battery according
to the manufacturer’s instructions.
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being
dropped), or any unusual smells emanating from the notebook battery, shut your computer
down immediately and contact your service center. If the battery has bee n d roppe d we do
not recommend using it any further, as even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire . It is
recommended that you replace your computer battery every two years.
Damaged Battery Warning
3 - 12 Battery Life
Battery FAQ
How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t
turn off the computer even if a message indicates the battery is critically low, just let
the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for dischar ging the battery and set all the options to Never.
3. Click Change plan settings (after saving it) and click Change advanced power
settings.
Power Management
3
Figure 3 - 7
Power Plan Create
Battery Life3-13
Power Management
4. Scroll down to Battery and click + to expand the battery options.
5. Choose the options below (click Yes if a warning appears):
3
Figure 3 - 8
Power Options
Advanced Settings -
Battery
• Low battery levels = 0%
• Critical battery Levels = 0%
• Low battery action = Do Nothing
• Critical battery action (On battery) = Shut Down
• Critical battery action (Plugged in) = Do Nothing
3 - 14 Battery Life
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes
from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after
about 20 partial discharges.
Power Management
3
Battery Life3-15
Power Management
3
3-16
Chapter 4: Drivers & Utilities
Drivers & Utilities
This chapter deals with installing the drivers and utilities essential to the operation or improvement of some
of the computer’s subsystems. The system takes advantage of some newer hardware components for
which the latest versions of most available operating
systems haven’t built in drivers and utilities. Thus,
some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to
manually install some system-required drivers and
utilities.
RAID Setup
Note that setting up the RAID system and installing
the driver for Windows needs to be done prior to installing the Windows OS, and therefore before installing the other drivers listed here (see “Setting Up
SATA RAID” on page 7 - 16).
What to Install
The Device Drivers & Utilities + User’s Manual CDROM (Win Vista OR WinXP) contains the drivers and
utilities necessary for the proper operation of the computer. There will be two CDs provided; one will contain drivers for Windows Vista, the other will contain
drivers for Windows XP (make sure you install the appropriate drivers for your system).
Table 4 - 1, on page 4 - 3 lists what you need to install
and it is very important that the drivers are in-
stalled in the order indicated (see “Driver Installa-
tion” on page D - 21 for Windows XP information).
Module Driver Installation
The procedures for installing drivers for the WLAN,
PC Camera, Bluetooth, TV Tuner and RAID mod-
ules are provided in “Modules” on page 7 - 1. Only install drivers for modules included in your purchase
option.
4
What to Install 4 - 1
Drivers & Utilities
Driver Installation
Insert the Device Drivers & Utilities + User’s Manual
CD-ROM and click Install Drivers (button) > Yes, or
Optional (button) > Yes, to access the Optional driver
menu.
4
If you wish to install the drivers manually see page
4 - 3
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the dri ve r s mus t be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, after
installing each driver it will become grayed out (if
you need to reinstall any driver, click the Unlock
.
button).
3. Follow the instructions for each individual driver
installation procedure as listed on the following
pages.
Figure 4 - 1 - Drivers Installer Screen 1
4 - 2 Driver Installation
Figure 4 - 2 - Drivers Installer Screen 2
Drivers & Utilities
Manual Driver Installation
If you wish to install the drivers manually, click the Exit button to quit the Drivers Installer application, and
then browse to the executable file in the location listed in the table below and follow the installation procedure
for each driver. Note that X is the drive letter assigned to the CD/DVD-ROM drive.
Driver Page Driver Location
Video (VGA) Page 4 - 5
Audio Page 4 - 5
Modem Page 4 - 5
TouchPad Page 4 - 6
Card Reader/ExpressCard Page 4 - 6
Hot Key Utility Page 4 - 6
Wireless LAN Page 7 - 2
PC Camera Page 7 - 7
Bluetooth Page 7 - 12
TV Tuner Page 7 - 14
Table 4 - 1 - Driver Installation and Location
Vista 64bit: X:\Drivers\01VGA\Nvidia\64bit\setup.exe
Vista 64bit: X:\Drivers\02Audio\Setup.exe
Vista 64bit: X:\Drivers\03Modem\64bit\Setup64.exe
Vista 64bit: X:\Drivers\05TouchPad\E l antech\64bit\setup.exe
Vista 64bit: X:\Drivers\05TouchPad\S ynaptics\64bit\setup.exe
Vista 64bit: X:\Drivers\06PCMCIA\64bit\setup.exe
Vista 64bit: X:\Drivers\07Ap-key\1AP.exe
Vista 64bit: X:\Others\01WLan\Intel\iProDifX.exe
Vista 64bit: X:\Others\01WLan\AzureW\setup.exe
Vista 64bit: X:\Oth ers\02Camera\64bit\setup.exe
Vista 64bit: X:\Others\03Bluetooth\setup.exe
Supplied on Separate CD
Driver Installation 4 - 3
4
Drivers & Utilities
Updating/Reinstalling Individual Drivers
If you wish to update/reinstall individual drivers it
may be necessary to uninstall the original driver.To do
this go to the Control Panel in the Windows OS and
double-click the Programs and Features icon (Pro-
4
grams > Uninstall a program). Click to select the
driver (if it is not listed see below) and click Uninstall,
and then follow the on screen prompts (it may be necessary to restart the computer). Reinstall the driver as
outlined in this chapter.
If the driver is not listed in the Programs and Fea-
tures menu:
1. Click Start, and click Control Panel (or point to
Settings and click Control Panel).
2. Double-click Device Manager (Hardware and
Sound > Device Manager).
3. Double-click the device you wish to update/reinstall
the driver for (you may need to click “+” to expand
the selection).
4. Click Driver (tab) and click the Update Driver or
Uninstall button and follow the on screen prompts.
User Account Control (Win Vista)
If a User Account Control prompt appears as part of
the driver installation procedure, click Continue or
Allow, and follow the installation procedure as directed.
Windows Security Message
If you receive a Windows security message as part of
the driver installation process. Just click “Install this
driver software anyway” or Install to continue the in-
stallation procedure.
You will receive this message in cases where the driver has been released after the version of Windows you
are currently using. All the drivers provided will have
already received certification for Windows.
New Hardware Found
If you see the message “New Hardware Found”
(Found New Hardware Wizard) during the installation procedure (other than when outlined in the
driver install procedure), click Cancel to close the
window, and follow the installation procedure.
4 - 4 Driver Installation
Drivers & Utilities
Driver Installation Procedure
Chipset
This driver is included in the Windows Vista OS and
therefore does not need to installed from the CD.
Video (VGA)
1. Click 2.Install Video Driver > Yes.
2. Click Next (click “Install this driver software
anyway” if asked if you want to continue).
3. Click Finish to restart the computer.
Audio
1. Click 3. Install Audio Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
Modem
1. Click 4.Install Modem Driver > Yes.
2. Click OK > OK.
3. The modem is now ready for configuration.
4
Modem Country Selection
Go to the Phone and Modem Options control panel
(Hardware and Sound) and make sure the modem
country selection is appropriate for you.
LAN
This driver is included in the Windows Vista OS and
therefore does not need to installed from the CD.
Driver Installation 4 - 5
Drivers & Utilities
TouchPad
1. Click
6.Install Touchpad Driver > Yes
2. Click Next > Finish.
3. Click Restart Now to restart the computer.
4. You may then configure your TouchPad as out-
4
lined in “TouchPad and Buttons/Mouse” on
page 2 - 9.
Card Reader/ExpressCard
1. Click
7.Install PCMCIA Driver > Yes
2. Click Next.
3. Click the button to accept the license, and then
click Next.
4. Click Finish.
Hot Key Utility
1. Click 8.Install Hotkey Utility > Yes.
2. Click Next.
3. Click Finish to restart your computer.
4. See configuration instructions for the Applica-
tion Hot Key on page 2 - 8.
Optional Drivers
.
.
See the pages indicated for the driver installation procedures for any modules included in your purchase option.
Figure 4 - 3 - Optional Drivers Installer Screen
4 - 6 Driver Installation
Wireless LAN
See the appropriate install procedure for your WLAN
module in “Intel WLAN Driver Installation” on
page 7 - 2/“802.11 b/g WLAN Driver Installation” on
page 7 - 2.
PC Camera
See the install procedure in “PC Camera Driver In-
stallation” on page 7 - 7.
Bluetooth
See the install procedure in “Bluetooth Driver Instal-
lation” on page 7 - 12.
TV Tuner
See the install procedure in “Mini-PCI TV Tuner
Module” on page 7 - 14.
Drivers & Utilities
4
Driver Installation 4 - 7
Drivers & Utilities
4
4-8
BIOS Utilities
Chapter 5: BIOS Utilities
Overview
This chapter gives a brief introduction to the computer’s built-in software:
Diagnostics: The POST (Power-On Self Test)
Configuration: The Setup utility
If your computer has never been set up, or you are mak ing important chan ges to the
system (e.g. hard disk setup), then you should review this chapter first and note the
original settings found in Setup. Even if you are a beginner, keep a record of the settings you find and any changes you make. This information could be useful if your
system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you
are doing. Many of the settings are required by the system, and changing them could
cause it to become unstable or worse. If you have any doubts, consult your service
representative.
BIOS Settings
Warning
Incorrect settings can
cause your system to
malfunction. To correct
mistakes, return to Set-
up and restore the Setup Defaults with <F9>.
5
Overview 5 - 1
BIOS Utilities
The Power-On Self Test (POST)
POST Screen
1.BIOS information
2.CPU type
3.Memory status
5
4.Enter Setup prompt
appears only during
POST
Note: The POST screen
as pictured is for guideline purposes only.
Figure 5 - 1
POST Screen
Each time you turn on the computer, the system takes a few seconds to conduct a
POST, including a quick test of the on-board RAM (memory).
As the POST proceeds, the computer will tell you if there is anything wrong. If there
is a problem that prevents the system from booting, it will display a system summary
and prompt you to run Setup.
If there are no problems, the Setup prompt will disappear and the system will load
the operating system. Once that starts, you can’t get into Setup without rebooting.
Phoenix TrustedCore(tm) NB
Copyright 1985-2005 Phoenix Technologies Ltd.
All Rights Reserved
BIOS Revision: 1.01.06
KBC/EC Revision: 1.00.04
CPU=1Processor Detected, Cores per Processor = 2
Intel(R) Core(TM)2 CPU T7200 @ 2.00GHz
1024M System RAM Passed
4096 KB L2 Cache
System BIOS shadowed
Video BIOS shadowed
Fixed Disk 0: TOSHIBA MK6034GSX
ATAPI CD-ROM: PIONEER DVD-RW DVR-K16RS
Mouse intialized
3
1
2
Press <F2> to enter SETUP
5 - 2 The Power-On Self Test (POST)
4
Failing the POST
Errors can be detected during the POST. There are two categories, “fatal” and “nonfatal”.
Fatal Errors
These stop the boot process and usually indicate there is something seriously wrong
with your system. Take the computer to your service representative or authorized
service center as soon as possible.
Non-Fatal Errors
This kind of error still allows you to boot. You will get a message identifying the
problem (make a note of this message!) followed by the prompt:
• Press <F1> to resume
• <F2> to enter Setup
Press F1 to see if the boot process can continue. It may work, without the correct
configuration.
Press F2 to run the Setup program and try to correct the problem. If you still get an
error message after you change the setting, or if the “cure” seems even worse, call
for help.
BIOS Utilities
5
The Power-On Self Test (POST) 5 - 3
BIOS Utilities
The Setup Program
The Phoenix Setup program tells the system how to configure itself and manage ba-
sic features and subsystems (e.g. port configuration).
Entering Setup
To enter Setup, turn on the computer and press F2 during the POST. The prompt
5
(Press F2 to Enter Setup) seen in Figure 5 - 1 on page 5 - 2 is usually present for a
few seconds after you turn on the system. If you get a “Keyboard Error”, (usually
because you pressed F2 too quickly) just press F2 again.
If the computer is already on, reboot using the Ctrl + Alt + Delete combination and
then hold down F2 when prompted. The Setup main menu will appear.
5 - 4 The Setup Program
Setup Screens
The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with five (5) menu headings. When you
select a heading, a new screen appears. Scroll through the features listed on each
screen to make changes to Setup.
Instructions on how to navigate each screen are in the box along the bottom of the
screen. If these tools are confusing, press F1 to call up a General Help screen, and
then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted
item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that subject. The sub-menu screen that appears has a similar layout, but the Enter key may
execute a command.
BIOS Utilities
Setup Menus
The Setup menus
shown in this section are
for reference only. Your
computer’s menus will
indicate the configuration appropriate for your
model and options.
5
The Setup Program 5 - 5
BIOS Utilities
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
<Tab>, <Shift Tab>, or
<Enter> selects field.
Main
System Time: [16:11:05]
System Date: [01/10/2007]
IDE Channel 0 Master [TOSHIBA MK6034GSX-(SD1)]
IDE Channel 0 Slave [None]
IDE Channel 1 Slave [PIONEER DVD-RW DVR-K16RS-]
System Memory 1024 MB
Available to OS 1023 MB
VGA Card: nVIDIA 7950 GTX
VBIOS Revision 5.71.22.38.21
VBIOS Build Date 08/31/06
Main Menu
Figure 5 - 2
Main Menu
5
5-6Main Menu
System Time & Date (Main Menu)
The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you
can change the date and time settings in your operating system, you will also change
these settings. Some applications may also alter data files to reflect these changes.
IDE Channel 0/1 Master/Slave (Main Menu)
Pressing Enter here opens the sub-menu to show the configuration of hard disks and
CD/DVD device(s) on the computer’s IDE Channels. Use the Auto (Type:) setting
to have the items configured automatically for you.
Installed Memory (Main Menu)
This item contains information on the system memory, and is not user configurable.
The system will auto detect the amount of memory installed.
The Main menu also contains information on your video card and video BIOS version.
BIOS Utilities
5
Main Menu 5 - 7
BIOS Utilities
Advanced Menu
Figure 5 - 3
Advanced Menu
5
Main Advanced Security Power Boot Exit
Advanced Chipset Control
National 381 SIO Control Sub-Menu
Reset Configuration Data: [No]
Legacy USB Support: [Enabled]
Boot-time Diagnostic Screen: [Enabled]
Power on Boot Beep: [Disabled]
Battery Low Alarm Beep: [Enabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Advanced
PhoenixBIOS Setup Utility
Item Specific Help
Select options for
Advanced Chipset
features.
5 - 8 Advanced Menu
Advanced Chipset Control (Advanced Menu)
Pressing Enter here will access the sub-menus which allow you to adjust advanced
CPU controls. You can also enable/disable the SATA RAID function (see “Setting
Up SATA RAID” on page 7 - 16), and the PXE OPROM (network boot) option.
PhoenixBIOS Setup Utility
Advanced
Advanced
Advanced Chipset Control
Core Multi-Processing: [Enabled]
Processor Power Management: [Enabled]
Enhanced C-States Enable: [Enabled]
SATA RAID Function: [Enabled]
PXE OPROM: [Disabled]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Enable SATA RAID
functionality.
BIOS Utilities
5
Figure 5 - 4
Advanced Chipset
Control Menu
Advanced Menu 5 - 9
BIOS Utilities
National 381 SIO Control Sub-Menu (Advanced Menu)
The sub-menus under this item allow you to enable/disable the Serial port A (Serial
Mouse), and FIR (Infrared) transceiver.
Reset Configuration Data: (Advanced Menu)
This item is set to No as default. You can change the setting to Yes if you have installed a new add-on which has reconfigured the system, resulting in such a serious
5
system conflict that the operating system is unable to boot.
Legacy USB Support: (Advanced Menu)
Use this menu item to enable/disable the support for Legacy Universal Serial Bus.
Boot-time Diagnostic Screen: (Advanced Menu)
Use this menu item to enable/disable the Boot-time Diagnostic Screen (or POST
screen - see “The Power-On Self Test (POST)” on page 5 - 2).
Power On Boot Beep: (Advanced Menu)
Use this menu to enable/disable the single beep sound at the end of the POST. This
item is “Disabled” by default.
5 - 10 Advanced Menu
Battery Low Alarm Beep: (Advanced Menu)
Use this menu item to enable/disable the battery low alarm beep.
Security Menu
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
Security
BIOS Utilities
Figure 5 - 5
Security Menu
Supervisor Password Is: Clear
Set Supervisor Password [Enter]
Password on boot: [Disabled]
Fixed disk boot sector: [Normal]
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Item Specific Help
Supervisor Password
controls access to the
setup utility.
Set Supervisor Password (Security Menu)
You can set a password for access to the Setup utility. This will not affect access to
the computer OS, (only the Setup utility) unless you choose to set a Password on
Boot (see over).
5
Security Menu
The changes you
make here affect the
access to the Setup
utility itself, and also
access to your machine as it boots up after you turn it on.
These settings do not
affect your machine or
network passwords
which will be set in
your software OS.
Security Menu 5 - 11
BIOS Utilities
Password on boot: (Security Menu)
Password Warning
If you set a boot password (Password on boot
is “Enabled“), NEVER
forget your password.
5
The consequences of
this could be serious. If
you cannot remember
your boot password you
must contact your vendor and you may lose all
of the information on
your hard disk.
Specify whether or not a password should be entered to boot the computer. If “Enabled” is selected, only users who enter a correct password can boot the system (see
the warning in the sidebar). The default setting is “Disabled”.
Note: To clear existing passwords press Enter and type the existing password, then
press Enter for the new password (without typing any password entry) and Enter
again to confirm the password clearance.
Fixed disk boot sector: (Security Menu)
If you choose “Write Protect” this will protect against viruses being written to the
hard disk boot sector (this is not a substitute for installing an anti- virus program - see
“Viruses” on page 8 - 4).
5 - 12 Security Menu
Boot Menu
PhoenixBIOS Setup Utility
Main Advanced Security Exit
Boot priority order:
1: USB FDC:
2: USB KEY:
3: IDE CD: PIONEER DVD-RW DVR-K16RS-(
4: IDE HDD: TOSHIBA MK6034GSX-(S1)
5: PCI SCSI:
6: PCI BEV:
7:
8:
Excluded from boot order:
: USB HDD:
: USB CDROM:
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
When you turn the computer on it will look for an operating system (e.g. WindowsXP) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in
the order specified in the Boot priority order. Item specific help on the right is
available to help you move devices up and down the order.
Boot
Item Specific Help
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<f> and <r> specifies
the device fixed or
removable.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
<1 - 4> Loads default
boot sequence.
BIOS Utilities
Figure 5 - 6
Boot Menu
5
Boot Menu 5 - 13
BIOS Utilities
Exit Menu
Figure 5 - 7
Exit Menu
5
Main Advanced Security Boot Exit
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help Select Item -/+ Change Values F9 Setup Defaults
Esc Exit Select Menu Enter Execute Command F10 Save and Exit
PhoenixBIOS Setup Utility
Exit
Item Specific Help
Exit System Setup and
save your changes to
CMOS.
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any
changes you have made to the Setup. You can also choose to restore the original Set-
up defaults that will return the Setup to its original state, and erase any previous
changes you have made in a previous session.
5 - 14 Exit Menu
Upgrading The Computer
Chapter 6: Upgrading The Computer
Overview
This chapter contains information on upgrading the computer. Follow the steps outlined to make the desired upgrades. If you have any trouble or problems you can contact your service representative for further help. Before you begin you will need:
• A small crosshead or Phillips screwdriver
• A small regular slotted (flathead) screwdriver
• An antistatic wrist strap
Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the components.
The chapter includes:
• Removing the Battery
• Upgrading the Hard Disk Drive(s)
• Upgrading the System Memory (RAM)
• Upgrading the Optical (CD/DVD) Device(s)
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Please make sure that you review each procedure before you perform it.
Overview 6 - 1
Upgrading The Computer
When Not to Upgrade
Power Safety Warning
These procedures involve opening the system’s case, adding and sometimes replacing parts.You should not perform any of these upgrades if:
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals and
6
cables (including telephone lines). It is advisable to also remove your
battery in order to prevent accidentally turning
the machine on.
6 - 2 Overview
• Your system is still under warranty or a service contract
• You don’t have all the necessary equipment
• You’re not in the correct environment
• You doubt your abilities
Under any of these conditions, contact your service representative to purchase or re-
place the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember
to replace the cover(s) and screw(s) before turning the computer on.
Upgrading the Processor
If you want to upgrade your computer by replacing the existing processor with a faster/new one you will need to contact your customer service representative. We recommend that you do not do this yourself, since if it is done incorrectly you may
damage the processor or mainboard.
Upgrading The Computer
Removing the Battery
If you are confident in undertaking upgrade procedures yourself, for safety reasons
it is best to remove the battery.
1. Turn the computer off, turn it over and remove the battery.
2. Slide latch towards the unlock symbol and hold it in place, and lift the battery
2
up and out of the battery bay.
1
1
2
Warranty Warning
Please check with your
service representative
before undertaking any
upgrade procedures to
find out if this will VOID
your warranty.
6
Figure 6 - 1
Battery Removal
Removing the Battery 6 - 3
Upgrading The Computer
Upgrading the Hard Disk Drive(s)
HDD System Warning
New HDD’s are blank. Before you begin make sure:
You have backed up any
data you want to keep from
your old HDD.
You have all the CD-ROMs
and FDDs required to in-
6
stall your operating system
and programs.
If you have access to the internet, download the latest
application and hardware
driver updates for the operating system you plan to install. Copy these to a
removable medium.
Figure 6 - 2
HDD Bay Cover
Removal
The hard disk drive(s) can be taken out to accommodate other 2.5" serial (SATA)
hard disk drives with a height of 9. 5mm (h) (see “ Storag e Options” on page C - 4).
Follow your operating system’s installation instructions, and install all necessary
drivers and utilities (as outlined in “Drivers & Utilities” on page 4 - 1), when setting
up a new hard disk.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the hard disk bay cover and remove screws - .
3. Remove the ba y cov er .
12
1 11
1 32 4
5
6
9
10
7
11
8
12
6 - 4 Upgrading the Hard Disk Drive(s)
Upgrading The Computer
4. Remove screws - and lift the bracket up from the hard disk.
5. Slide the hard disk in th e dir ec tion of the ar ro w .
6. Remove the ha rd di sk .
7. Insert the new hard disk into the computer.
8. Re-Insert the bracket and insert screws
14 17
18
19
19
18
14 17
- .
14 15
Figure 6 - 3
HDD Removal
1617
6
Upgrading the Hard Disk Drive(s) 6 - 5
Upgrading The Computer
Upgrading the System Memory (RAM)
The computer has two memory sockets for 200 pin Small Outline Dual In-line (SODIMM) DDR II (DDR2) type memory modules (see “Memory” on page C - 2). The
total memory size is automatically detected by the POST routine once you turn on
your computer.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the hard disk bay cover and remove screws - .
3. Remove the ba y cov er .
12
6
1 32 4
Figure 6 - 4
Bay Cover Screws
5
6
9
10
7
11
8
12
1 11
6 - 6 Upgrading the System Memory (RAM)
Upgrading The Computer
4. Gently pull the two release latches ( & ) on the sides of the memory socket in
the direction indicated by the arrows in Figure 6 - 5.
13
5. The RAM module will pop-up, and you can remove it.
15
15 15
13 14
14
Figure 6 - 5
RAM Module
Release
Contact Warning
Be careful not to touch
the metal pins on the
module’s connecting
edge. Even the cleanest
hands have oils which
can attract particles, and
degrade the module’s
performance.
Figure 6 - 6
RAM Module
Removal
6
6. Pull the latches to release the second module if necessary.
Upgrading the System Memory (RAM) 6 - 7
Upgrading The Computer
7. Insert a new module holding it at about a 30° angle and fit the connectors firmly
into the memory socket.
8. The module’s pin alignment will allow it to only fit one way. Make sure the module
is seated as far into the socket as it will go. DO NOT FORCE the module; it should
fit without much pressure.
9. Press the modu le in an d down towa r ds th e ma inbo ar d until th e soc ke t leve rs click
into place to secure the module.
10. Replace the cover and screws (see Figure 6 - 4).
1 1. Restart the computer to allow the BIOS will register the new memory configuration
as it starts up.
6
6 - 8 Upgrading the System Memory (RAM)
Upgrading The Computer
Upgrading the Optical (CD/DVD) Device(s)
1. Turn the computer off, turn it over and remove the battery.
2. Slide the latch towards the unlock symbol and hold it in place.
3. Slide latch (while still holding latch in place) in the direction indicated by the
arrow in order to push the device out of the computer.
1
2 1
2
1
Figure 6 - 7
Removing the CD/
DVD Device(s)
6
Upgrading the Optical (CD/DVD) Device(s) 6 - 9
Upgrading The Computer
6
6-10
Loading...