Clevo M540SE, M550SE User guide

Preface

Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, trans­mitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trade­marks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©August 2007
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain U.S. pat­ents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended fo r home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineer­ing or disassembly is prohibited. Intel, Celeron, and Intel Core are trademarks/registered trademarks of Intel Corporation.
I
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in­stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Re orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not ex­pressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.
II
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sin k or laundry tub, in a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter - AC Input 100 ­240V, 50 - 60Hz / DC Output 19V, 3.42A or 18.5V, 3.5A (65W) minimum).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class 1 Product
III
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
Do not expose the computer to any shock or vibration.
Do not place it on an unstable surface.
Do not place anything heavy on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele- ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly dam­aged.
Do not expose it to excessive heat or direct sunlight.
Do not leave it in a place where foreign matter or mois­ture may affect the system.
Don’t use or store the com­puter in a humid environment.
Do not place the computer on any surface that will block the Vents/Fan Intakes.
IV
Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper workin g procedu res for t he computer. Shut the computer down proper ly and don ’t for ge t to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.
Do not turn off the power until you properly shut down all programs.
Do not turn off any peripheral devices when the computer is on.
5. Take care when using peripheral devices.
Use only approved brands of peripherals.
Do not disassemble the com­puter by yourself.
Unplug the power cord befor e attaching peripheral devices.
Perform routine maintenance on your computer.
V
Preface
Power Safety
The computer has specific power requirements:
Power Safety
Warning
Before you undertake any upgrade proce­dures, make sure that you have turned off the power, and discon­nected all peripherals and cables (including telephone lines). It is advisable to also re­move your battery in order to prevent acci­dentally turning the machine on.
VI
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for intern ational travel but it still re quires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-pr ong or a 3-prong ground ed plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power cord, be su re to disconnect it by the plug head, not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external power sup­plies (i.e. AC/DC adapter or car adapter).
Do not plug in the power cord if you are wet.
Do not use the power cord if it is broken.
Do not place heavy objects on the power cord.
Preface
Battery Precautions
Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
Do not remove any batteries from the computer while it is powered on.
Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service repre sent ative or qual­ified service personnel.
Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
Keep the battery away from metal appliances.
Affix tape to the battery contacts before disposing of the battery.
Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.
VII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
When the power cord or AC/DC adapter is damaged or frayed.
If the computer has been exposed to rain or other liquids.
If the computer does not work normally when you follow the operating instructions.
If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before turning the computer on.
VIII
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses volt ages from 100 to 240 volt s so you won’t need a second volt age adapter. However ,
check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any perip herals (e.g. a printer, mouse or digital camera), pack them and those devices’ adapters
and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or requ ire proof of ownershi p for both hard-
ware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container). Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre vent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in use.
IX
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful. Avoid knock­ing the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the com­puter, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the computer. Wait a few minutes before turning it on so that any moisture can evaporate.
X
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. The following are some tips to reduce the strain:
Adjust the height of the chair and/or desk so that the keyboard is at or slightly belo w the level of your elbow. Keep your forearms, wrists, and hands in a relaxed position.
Your knees should be slightly higher than your hips. Place your feet flat on the floor or on a footrest if necessary.
Use a chair with a back and adjust it to support your lower back comfortably.
Sit straight so that your knees, hips and elbows form approximately 90-degree angles when you are working.
Take periodic breaks if you are using the computer for long periods of time.
Remember to:
Alter your posture frequently.
Stretch and exercise your body several times a day.
Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XI
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.
Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
Position the display directly in front of you at a comfortable viewing distance.
Adjust the display-viewing angle to find the best position.
XII
Contents
Notice ................................................................................. I
FCC Statement .............................................................II
Instructions for Care and Operation ..........................IV
Power Safety ..............................................................VI
Battery Precautions ...................................................VII
Cleaning .................................................................. VIII
Servicing ................................................................. VIII
Travel Considerations ................................................IX
Quick Start Guide
Overview ........................................................................1-1
Model Differences .......................................................1-2
Advanced Users ...........................................................1-3
Beginners and Not-So-Advanced Users ......................1-3
Warning Boxes ............................................................1-3
Not Included ................................................................1-4
System Software ..........................................................1-5
System Startup ...............................................................1-6
System Map: Model A - LCD Panel Open ....................1-7
System Map: Model B - LCD Panel Open ....................1-8
LED Indicators ................................................. .... ..........1-9
Hot Key Buttons & Keyboard .....................................1-10
Function Keys ...................................................... .... ....1-11
Preface
System Map: Front & Rear Views ...............................1-12
System Map: Left View ...............................................1-13
System Map: Right View .............................................1-14
System Map: Bottom View ..........................................1-15
Windows Vista Start Menu & Control Panel ...............1-16
Video Features .............................................................1-17
Power Options ............................................ .... .... ..........1-18
Features & Components
Overview ........................................................................2-1
Hard Disk Drive .............................................................2-2
Optical (CD/DVD) Device ............................................2-3
Loading Discs ..............................................................2-3
Handling CDs or DVDs ...............................................2-4
DVD Regional Codes ..................................................2-5
7-in-1 Card Reader .........................................................2-6
ExpressCard Slot ............................................................2-7
Inserting and Removing ExpressCards ........................2-7
Application Hot Key ......................................................2-8
TouchPad and Buttons/Mouse .......................................2-9
Audio Features .............................................................2-10
Adding a Printer ................................................. .... ......2-11
USB Printer ..............................................................2-11
XIII
Preface
Parallel Printer ..........................................................2-11
Power Management
Overview ........................................................................3-1
The Power Sources ........................................................3-2
AC/DC Adapter ................................................. .... ......3-2
Battery .........................................................................3-2
Turning on the Computer ...............................................3-3
Power Plans ...................................................................3-4
System Power Options ...................................................3-6
Hibernate vs. Shut Down .............................................3-6
Sleep vs. Hibernate ......................................................3-6
Sleep ...........................................................................3-7
Hibernate ....................................................................3-7
Configuring the Power Buttons .....................................3-8
Battery Information .......................................................3-9
Battery Power .............................................................3-9
Conserving Battery Power ...........................................3-10
Battery Life .............................................................. ....3-11
New Battery ..............................................................3-11
Recharging the Battery with the AC/DC Adapter .....3-11
Proper handling of the Battery Pack .........................3-12
Battery FAQ ..............................................................3-13
Drivers & Utilities
What to Install ............................................................... .4-1
Module Driver Installation ..........................................4-1
Driver Installation ..........................................................4-2
Updating/Reinstalling Individual Drivers ...................4-3
Manual Driver Installation .........................................4-4
User Account Control (Win Vista) ..............................4-5
Windows Security Message .........................................4-5
New Hardware Found ..................................................4-5
Driver Installation Procedure .......................................4-5
Video ..........................................................................4-5
Audio ..........................................................................4-5
Modem ........................................................................ 4-6
LAN ............................................................................4-6
TouchPad .................................................................... 4-6
CardReader ................................................................. 4-6
Hot Key ......................................................................4-6
Wireless LAN .............................................................4-7
Bluetooth ....................................................................4-7
PC Camera ..................................................................4-7
BIOS Utilities
Overview ........................................................................5-1
Startup Screen ................................................................5-2
Setting a Boot Password ..............................................5-4
XIV
Preface
Setup Screens ......................................................... ......5-5
Main Menu .....................................................................5-6
System Time & Date (Main Menu) ...............................5-6
IDE Channel 0/2 Master (Main Menu) ..........................5-7
System/Extended Memory: (Main Menu) .....................5-7
Advanced Menu .............................................................5-8
Installed O/S: (Advanced Menu) ...................................5-8
Legacy USB Support: (Advanced Menu) ......................5-9
Reset Configuration Data: (Advanced Menu) ...............5-9
Enable Multimedia Timer: (Advanced Menu) ..............5-9
Frame Buffer Size: (Advanced Menu) ..........................5-9
Boot Menu ...................................................................5-10
Exit Menu ....................................................................5-11
Upgrading The Computer
Overview ........................................................................6-1
When Not to Upgrade ..................................................6-2
Removing the Battery ....................................................6-3
Upgrading the Hard Disk Drive .....................................6-5
Upgrading the Optical (CD/DVD) Device ....................6-9
Upgrading the System Memory (RAM) ......................6-11
Upgrading the Processor ..............................................6-14
Modules & Options
Overview ........................................................................7-1
802.11 b/g USB WLAN Module ...................................7-2
802.11 b/g WLAN Driver Installation ........................7-2
Connecting to a Wireless Network .............................. 7-3
Windows Mobility Center ...........................................7-6
Bluetooth Module ..........................................................7-7
Bluetooth Driver Installation ......................................7-7
PC Camera Module ......................................................7-11
PC Camera Driver Installation .................................7-11
PC Camera Audio Setup ...........................................7-12
BisonCap ...................................................................7-14
Eliminating Screen Flicker .......................................7-15
Troubleshooting
Overview ........................................................................8-1
Basic Hints and Tips ......................................................8-2
Backup and General Maintenance .................................8-3
Viruses ...........................................................................8-4
Upgrading and Adding New Hardware/Software .......... 8-5
Problems and Possible Solutions ...................................8-7
Non DDC CRT Monitors (for Win Vista Only) ..........8-12
Interface (Ports & Jacks)
Overview ....................................................................... A-1
Notebook Ports and Jacks .............................................A-2
Card Reader Port ...........................................................A-2
XV
Preface
DC-In Jack ....................................................................A-2
External Monitor (VGA) Port .......................................A-2
Headphone-Out Jack .....................................................A-2
Recording Line-In Jack .................................................A-2
Microphone-In Jack ......................................................A-2
RJ-11 Modem Jack .......................................................A-3
RJ-45 LAN Jack ...........................................................A-3
Security Lock Slot ........................................... .... .... .....A-3
S/PDIF-Out Jack ...........................................................A-3
USB 2.0/1.1 Ports .........................................................A-3
Video Driver Controls
VIA Video Driver Installation ...................................... B-1
Video ......................................................................... B-1
Advanced Video Controls ............................................. B-2
Video Driver Controls ............................................... B-2
Video Memory ...........................................................B-2
VIA S3Tray Plus Utility .............................................B-3
Attaching Other Displays ............................................. B-4
Display Modes ..............................................................B-6
Specifications
Processor .......................................................................C-2
Core Logic ....................................................................C-2
Memory .........................................................................C-2
Security ......................................................................... C-2
BIOS .............................................................................C-2
LCD ..............................................................................C-3
Video Adapter ...............................................................C-3
Storage .......................................................................... C-3
Audio ............................................................................C-3
Keyboard & Pointing Device ........................................C-3
Interface ........................................................................ C-4
Card Reader ..................................................................C-4
ExpressCard Slot ...........................................................C-4
Communication .............................................................C-4
Power Management ............................................... ... ....C-4
Power ............................................................................ C-4
Environmental Spec ......................................................C-5
Physical Dimensions & Weight ....................................C-5
Optional ........................................................................C-5
Windows XP Information
Video Driver Controls ...............................................D-8
Video Memory ...........................................................D-8
VIA S3Tray Plus Utility .............................................D-9
Advanced Configuration and Power Interface .........D-15
AC/DC Adapter ........................................................D-16
Battery ......................................................................D-16
Hibernate Mode vs. Shutdown .................................D-20
XVI
Stand by Mode vs. Hibernate Mode .........................D-20
Recharging the Battery with the AC/DC Adapter ....D-24
Battery FAQ .............................................................D-26
Updating/Reinstalling Individual Drivers ................D-29
Authorized Driver Message ......................................D-30
Version Conflict Message ........................................D-30
BisonCap ..................................................................D-43
Preface
XVII
Preface
XVIII
Quick Start Guide

Chapter 1: Quick Start Guide

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:
Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 7-in-1 card reader, ExpressCard), Application Hot Key, TouchPad & Mouse, Audio and Printer.
Chapter 3 The computer’s power saving options.
Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
Chapter 6 Instructions for upgrading your computer.
Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, and PC Camera modules (some of which may be optional depending on your purchase configuration).
Chapter 8 A troubleshooting guide.
Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external devices.
Appendix B Information on the VIA Video driver controls.
Appendix C The computer’s specification.
• Appendix D Information on the Windows XP OS.
1
Overview 1 - 1
1
Quick Start Guide

Model Differences

This notebook series includes two different model types (each model includes two design styles). The models differ slightly in design style including the LCD type, and the location of the card reader (the easiest way to dif­ferentiate between the model types is the location of the card reader).
Feature Model A Model B
LCD Type
Card Reader
Location
Memory Sockets Two 200 Pin SODIMM Sockets (DD2 533/667) One 200 Pin SODIMM Sockets (DD2 533/667)
Design Styles
(see “LCD” on page C - 3 for details)
15.0" Flat Panel TFT (see “LCD” on page C - 3 for details)
Left Side Front
14.1" Flat Panel TFT
Table 1 - 1 - Model Differences
1 - 2 Overview
Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand every­thing the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a
as indicated in the margin.
For a more detailed description of any of the interface ports and jacks see “Interface
(Ports & Jacks)” on page A - 1.
Check the light colored boxes with the mark above to find detailed information about the computer’s features.
Notes

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1
Overview 1 - 3
1
Quick Start Guide

Not Included

Operating Systems (e.g. Windows Vista/Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com­puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4 - 3. You will be unable to use most advanced controls until the necessary drivers and util­ities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.
Ports and Jacks
See “Notebook Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your com­puter to communicate with external devices, connect to the internet etc.
1 - 4 Overview
Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the following operating systems are sup­ported.
Operating System & Version Supported Note
*Windows XP (Home or Professional) Yes
1
Windows Vista Home Basic
Windows Vista Home Premium
Windows Vista
Business/Enterprise/Ultimate
Table 1 - 2 - Operating Systems Supported
32-bit Yes 64-bit No 32-bit No 64-bit No 32-bit No 64-bit No
In order to run Windows Vista without limitations or decreased performance, your computer requires a minimum 1GB of system memory (RAM).
*Note: For information on the Windows XP OS (specifically power, video and driver information) see “Win-
dows XP Information” on page D - 1.
Overview 1 - 5
1
Quick Start Guide

System Startup

1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
5. Raise the lid/LCD to a comfortable viewing angle, and press the power button to turn the computer “on”.
6. Adjust the LCD panel to a comfortable viewing angle.
7. The LED Power & Communication indicators show the power and battery status of the computer.
Shutdown
Note that you should always shut your computer down by choos­ing the Shut Down command from the Lock Button Menu in Windows Vista. This will help prevent hard disk or system prob­lems.
Figure 1 - 1 - Computer with AC/DC Adapter Plugged-In
1 - 6 System Startup

System Map: Model A - LCD Panel Open

Quick Start Guide
1
Wireless Device
Operation Aboard
Aircraft
The use of any portable elec­tronic transmission devices aboard aircraft is usually pro­hibited. Make sure the mod­ule(s) are OFF if you are using the computer aboard aircraft.
Use the key combinations to toggle power to the WLAN/ Bluetooth modules, and check the status indicator icon to see if the modules are powered on or not (see “LED Indicators”
on page 1 - 9/“Function Keys” on page 1 - 11).
1
2
3
4
5
6
7
8
9
Figure 1 - 2 - Model A - LCD Panel Open
1. Optional Built-In PC Camera
2. LCD
3. LED Status Indicators
4. Hot Key Buttons
5. Power Button
6. Keyboard
7. Built-In Microphone
8. TouchPad and Buttons
9. LED Power & Communication Indicators
4
5
Note: Only One Design Style is Pictured
3
System Map: Model A - LCD Panel Open 1 - 7
1
Quick Start Guide

System Map: Model B - LCD Panel Open

1. Optional Built-In PC Camera
2. LCD
3. Speaker
4. LED Status Indicators
5. Hot Key Buttons
6. Power Button
7. Keyboard
8. TouchPad and Buttons
9. LED Power & Communication Indicators
10. Built-In Microphone
5
Note: Only One Design Style is Pictured
6
4
1
2
3
4
5
7
8
9
Figure 1 - 3 - Model B - LCD Panel Open
10
Wireless Device
Operation Aboard
Aircraft
The use of any portable elec­tronic transmission devices aboard aircraft is usually pro­hibited. Make sure the mod­ule(s) are OFF if you are using the computer aboard aircraft.
6
Use the key combinations to toggle power to the WLAN/ Bluetooth modules, and check the status indicator icon to see if the modules are powered on or not (see “LED Indicators”
on page 1 - 9/“Function Keys” on page 1 - 11).
1 - 8 System Map: Model B - LCD Panel Open
Quick Start Guide
1

LED Indicators

The two sets of LED indicators (LED Status Indica­tors and LED Power & Communication Indicators)
on the computer display helpful information about the current status of the computer.
Table 1 - 3 - LED Status Indicators
Icon Color Description
Green
Green Caps Lock Activated
Green
Number Lock Activated (to activate
press Fn & NumLk)
Scroll Lock Activated (to activate
press Fn & ScrLk)
Table 1 - 4 - LED Power & Communication Indicators
Icon Color Description
Green The Computer is On
Blinking
Green
Orange
Orange
Blinking
Orange
Green The Battery is Fully Charged Green Hard Disk Activity
Green
Orange
The Computer is in Sleep Mode
The AC/DC Adapter is Plugged
In & the Computer is Powered
Off
The AC/DC Adapter is Plugged
In & the Battery is Charging
The Battery has Reached
Critically Low Power Status
The WLAN Module is Powered
On
The Bluetooth Module is
Powered On
LED Indicators 1 - 9
1
Quick Start Guide

Hot Key Buttons & Keyboard

These buttons give instant access to the functions indi­cated in the table below.
Table 1 - 5 - Hot Key Buttons
Hot Key Function
Activate the user specified application
e.g.Microsoft Word or Excel
Activate the Default E-Mail Program
Activate the Default Internet Browser
See “Application Hot Key” on page 2 - 8 for configu- ration instructions.
Note: The hot key buttons may appear slightly differ­ent from those illustrated in Table 1 - 5, depending on your model/design.
The keyboard has an embedded numerical keypad for easy numeric data input, and features function keys to allow you to change operational features instantly (see
Figure 1 - 4).
Function Keys
NumLk &
Numeric
Keypad
Fn Key
Figure 1 - 4 - Keyboard
ScrLk Keys
Other Keyboards
If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically. However special functions/hot keys unique to the system’s regular keyboard may not work.
1 - 10 Hot Key Buttons & Keyboard
Quick Start Guide

Function Keys

To use the function keys, press and hold the Fn key, then press the appropriate function key (F1 - F12 etc.).
Key Function Key Function
Fn Function Key Fn + F7 Display Toggle
Fn + ~ Play/Pause (in Audio/Video Programs) Fn + F8 Decrease LCD Brightness
Fn + F1 TouchPad Toggle Fn + F9 Increase LCD Brightness
1
Fn + F2
Fn + F3 Mute Toggle Fn + F11 Wireless Power Toggle Fn + F4 Sleep Toggle Fn + F12 Bluetooth Power Toggle Fn + F5 Decrease Audio Volume Fn + NumLk Number Lock Toggle Fn + F6 Increase Audio Volume Fn + ScrLk Scroll Lock Toggle
(Press a key to or use TouchPad to turn on)
Turn LCD Backlight Off
Fn + F10 PC Camera Power Toggle
Table 1 - 6 - Function Keys
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters. These special characters ca n only be pro duced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will not work. Make sure that NumLk is on.
Function Keys 1 - 11
1
Quick Start Guide

System Map: Front & Rear Views

1. LED Power & Communication Indicators
2. LCD Latch (Model A Only)
3. 7-in-1 Card Reader (Model B Only)
4. External Monitor Port
5. Security Lock Slot
6. Battery
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
Model A - Front
1
Model B - Front
1
4
Figure 1 - 5 - Front & Rear Views
5
3
Rear
7-in-1 Card Reader
2
6
1 - 12 System Map: Front & Rear Views

System Map: Left View

Quick Start Guide
1
Model A - Left
6
1
2
3 4 5
Model B - Left
7
6
1
2
3
4 5
Figure 1 - 6 - Left View
1. RJ-45 LAN Jack
2. Vent/Fan Intake
3. 2 * USB 2.0 Ports
4. S/PDIF-Out Jack
5. Recording Line-In Jack (see page A - 2)
6. ExpressCard Slot
7. 7-in-1 Card Reader (
Model A
Only)
ExpressCard Slot
The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.
7-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
MS Duo (requires PC adapter) / Mini SD (requires PC adapter) / RS MMC (requires PC adapter)
System Map: Left View 1 - 13
1
Quick Start Guide

System Map: Right View

Figure 1 - 7 - Right View
1. Headphone-Out Jack
2. Microphone-In Jack
3. USB 2.0 Port
4. RJ-11 Modem Jack
5. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3)
6. DC-In Jack
1
32
4
5
6
Changing DVD Regional Codes
CD Emergency Eject
If you need to manually eject a CD/DVD (e.g. due to an une x­pected power interruption) you may push the end of a straight­ened paper clip into the emergency eject hole. Do not use a sharpened pencil or similar object that may break and become lodged in the hole.
Media Warning
Don’t try to remove a floppy disk/CD/DVD while the system is accessing it. This may cause the system to “crash”.
1 - 14 System Map: Right View
Go to the Control Panel and double-click Device Manager (Hardware and Sound), th en click the +
next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dia- logue box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the region­al code (see “DVD Regional Codes” on page 2 -
5).
DVD region detection is device dependent, not OS­dependent. You can select your module’s region code 5 times. The fifth selection is permanent. Th is cannot be altered even if you change your operating system or you use the module in another computer.

System Map: Bottom View

Quick Start Guide
1
CPU
The CPU is not a user ser­viceable part. Opening this compartment, or accessing the CPU at all, may violate your warranty.
Overheating
To prevent your computer from overheating make sure nothing blocks the Vent/Fan Intake while the computer is in use.
Model A
4
2
1
3
1
55
1. Vent/Fan Intake
2. Battery
3. Component Bay Cover
4. Hard Disk Cover
5. Speakers
2
Model B
1
4
1
1
3
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges (see “Battery Information” on page 3 - 9).
System Map: Bottom View 1 - 15
1
Quick Start Guide

Windows Vista Start Menu & Control Panel

Most of the control panels, utilities and programs within Windows Vista (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop. Right-click the Start menu icon , and then select Properties if you want to customize the appearance of the Start menu.
Click here to toggle Classic View
Figure 1 - 8 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows Vista provides basic controls for many of the fea- tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed in Table 4 - 1, on page 4 - 3. To see all controls it may be necessary to toggle to Classic View on.
1 - 16 Windows Vista Start Menu & Control Panel
Quick Start Guide

Video Features

You can switch display devices, and configure display options, from the Display Settings control panel (in Per­sonalization) in Windows Vista. For further information see “Video Driver Controls” on page B - 1.
To access Display Properties in Windows Vista:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Click Adjust screen resolution under the Appearance and Personalization menu (or double-click Personalization > Display Settings).
3. Move the slider to the preferred setting in Resolution: (Figure 1 - 9).
4. Click the arrow, and scroll to the preferred setting In Colors: (Figure 1 - 9).
5. Click Advanced Settings (button) (Figure 1 - 9) to bring up the Advanced Settings tabs.
6. Right-click the desktop and click Personalize, and then click Display Settings and adjust as above.
3
1
2
OR
Figure 1 - 9
Display Settings
1
1
2
3
Video Features 1 - 17
1
Quick Start Guide

Power Options

The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 1 - 16 ) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu. Note that the Power saver plan may have an affect on computer performance.
Click to select one of the existing plans, or click Create a power plan in the left menu and select the options to create a new plan. Click Change Plan Settings and click Change advanced power settings to access further con- figuration options.
Pay attention to the instructions on battery care in “Battery Information” on page 3 - 9.
1 - 18 Power Options
Note: Sleep is the default power saving state in Windows Vista
Figure 1 - 10 - Power Options
Features & Components

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components of the computer:
•Hard Disk Drive
Optical (CD/DVD) Device
7-in-1 Card Reader
ExpressCard Slot
Application Hot Key
TouchPad and Buttons/Mouse
Audio Features
Adding a Printer
2
Overview 2 - 1
Features & Components
2
Before attempting to ac­cess any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the ma­chine is turned off. Also ensure that all peripher­al cables, including phone lines, are discon­nected from the comput­er.
Power Safety
Figure 2 - 1
Hard Disk Location

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
The hard disk is accessible from the bottom of your computer as seen below. For fur­ther details see
“Upgrading the Hard Disk Drive” on page 6 - 5
Model A Model B
Hard Disk
.
Hard Disk
2 - 2 Hard Disk Drive
Features & Components

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de­vice will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 10).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupt­ed, insert an object such as a straightened paper clip into the emergency eject hole
3
to open the tray.
1
2
1
2
3
Sound Volume
Adjustment
How high the sound vol­ume can be set depends on the setting of the vol­ume control within Win- dows. Click the Volume icon on the taskbar to check the setting (see
“Audio Features” on page 2 - 10).
Figure 2 - 2
Optical Device
2
Optical (CD/DVD) Device 2 - 3
Features & Components
2
CD Emergency Eject
If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharp­ened pencil or similar object that may break and become lodged in the hole.
Disk Eject Warning
Don’t try to remove a CD/DVD while the sys­tem is accessing it. This may cause the system to “crash”.
Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.
Note the following:
Hold the CD or DVD by the edges; do not touch the surface of the disc.
Use a clean, soft, dry cloth to remove dust or fingerprints.
Do not write on the surface with a pen.
Do not attach paper or other materials to the surface of the disc.
Do not store or place the CD or DVD in high-temperature areas.
Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
Do not bend the CD or DVD.
Do not drop or subject the CD or DVD to shock.

Handling CDs or DVDs

2 - 4 Optical (CD/DVD) Device
Features & Components

DVD Regional Codes

To change the DVD regional codes see “Changing DVD Regional Codes” on
page 1 - 14.
.
DVD Regional Coding
Region Geographical Location
1 USA, Canada
2
3
4
5
6China
Western Europe, Japan, South
Africa, Middle East & Egypt
South-East Asia, Taiwan, South
Korea, The Philippines, Indonesia,
Hong Kong
South & Central America, Mexico,
Australia, New Zealand
N Korea, Russia, Eastern Europe,
India & Most of Africa
2
Table 2 - 1
DVD Regional Coding
Figure 2 - 3
DVD Regions
Optical (CD/DVD) Device 2 - 5
Features & Components
2
Card Reader Cover
Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust get­ting in to the card read­er.

7-in-1 Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the PCMCIA/Card Reader driver (see “CardReader” on page 4 - 6).
MMC (MultiMedia Card)
SD (Secure Digital)
MS (Memory Stick)
MS Pro (Memory Stick Pro)
MS Duo (requires PC adapter*)
Mini SD (requires PC adapter*)
RS MMC (requires PC adapter*)
*Note: The PC adapters are usually supplied with these cards.
Figure 2 - 4
Card Reader
1. Card Reader
Model A - Left
1
Model B - Front
1
2 - 6 7-in-1 Card Reader
Features & Components

ExpressCard Slot

The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards).
ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Ex­press Card/54 and 34mm for the ExpressCard/34.

Inserting and Removing ExpressCards

Align the ExpressCard with the slot and push it in until it locks into place.
To remove an ExpressCard, simply press the card to eject it.
ExpressCard
Slot Cover
Make sure you keep the rubber cover provided in the ExpressCard slot when not in use. This will help prevent foreign objects and/or dust get­ting in to the Express­Card Slot.
Figure 2 - 5
ExpressCard Slot
2
ExpressCard Slot 2 - 7
Features & Components
2
You will need to locate the actual application executable (.exe) file, not just the shortcut. To find the application right­click its shortcut on the desktop and click Prop-
erties. Click the short­cut (tab) and see where
the executable file is lo­cated by clicking the
Open File Location
(button).
Application.exe

Application Hot Key

The hot key buttons give instant access to the default Internet browser and e-mail program, and to a user-defined application, with one quick button press. To config­ure a program to open when the application hot key is pressed (Windows Me- dia Player is the default program), follow the instructions below.
1. Right click the hot key driver icon in the taskbar.
2. Select Setup from the menu, scroll to Application 1 and select Custom.
3. An Open dialog box will appear on the screen.
Figure 2 - 6
Application Hot Key
Configuration
4. Click Look in: and browse to the director y where th e desired ap plication .exe (see the sidebar) program exists.
5. Double-Click on the program file or choose Open.
2 - 8 Application Hot Key
Features & Components

TouchPad and Buttons/Mouse

The TouchPad is an alternative to the mouse; however, you can also add a mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Install the TouchPad driver (see “TouchPad” on page 4 - 6) and then double-click the TouchPad icon on the taskbar to configure the functions (tapping, buttons, scrolling, pointer motion and sensitivity) to your preferences. Further information is available at www.synaptics.com.
Mouse Driver
If you are using an ex­ternal mouse your op­erating system may be able to auto-configure your mouse during its installation or only en­able its basic functions. Be sure to check the device’s user docu­mentation for details.
Figure 2 - 7
Mouse Properties
2
TouchPad and Buttons/Mouse 2 - 9
Features & Components
2

Audio Features

You can configure the audio options on your computer from the Sound control
Sound Volume
Adjustment
The sound volume level is set using the volume control within Windows (and the volume func­tion keys on the comput­er). Click the volume icon in the taskbar to check the setting.
panel in Windows, or from the VIA Audio Deck icon in the taskbar, or on the desktop (this will bring up the VIA Audio Deck menu). The volume may also be adjusted by means of the Fn + F5/F6 key combination.
Click any of the buttons (e.g. ) on the left to expand the audio menu selections.
Figure 2 - 8
VIA Audio Deck
Configuration
Menus
2 - 10 Audio Features
Features & Components

Adding a Printer

The most commonly used peripheral is a printer. The following conventions will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options.

USB Printer

Most current printers have a USB interface connection. You may use any one of the ports to connect the printer.
Install Instructions:
1. Set up the printer according to its instruction s (unpacking, p aper tr ay, toner/ink car­tridge etc.).
2. Turn ON the computer.
3. Turn ON the printer.
4. Connect the printer’s USB cable to one of the USB ports on the computer.
5. Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen instructions.

Parallel Printer

This is still a very common type of printer. The install instructions are in the sidebar.
Parallel Printer
After setting up the print­er attach the parallel ca­ble to the printer.
Connect the printer’s parallel cable to the Par­allel to USB converter, and then plug the con­verter into the USB port.
Turn ON the printer, then turn ON the com­puter.
Windows will identify the printer and either load one of its own drivers or ask you to supply one. Follow the on-screen in­structions.
2
Adding a Printer 2 - 11
Features & Components
2
2-12
Power Management

Chapter 3: Power Management

Overview

To conserve power, especially when using the battery, your computer power man­agement conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system. This chapter covers:
The Power Sources
Turning on the Computer
Power Plans
System Power Options
Configuring the Power Buttons
Battery Information
The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user set­tings and information from applications.
OS Note
Power management functions will vary slight­ly depending on your operating system. For more information it is best to refer to the user’s manual of your operat­ing system.
(Note: All pictures used on the following pages are from the Windows Vista OS.)
3
Overview 3 - 1
Power Management

The Power Sources

The computer can be powered by either an AC/DC adapter or a battery pack.
3

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.
1. Attach the AC/DC adapter to the DC-in jack on the right of the computer.
2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.
3. Raise the lid/LCD to a comfortable viewing angle.
4. Press the power button to turn “On”.

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”
on page 3 - 13).
We recommend that you do not remove the battery. For more information on the bat­tery, please refer to “Battery Information” on page 3 - 9.
3 - 2 The Power Sources

Turning on the Computer

Now you are ready to begin using your computer. To turn it on simply press the pow­er button on the front panel.
When the computer is on, you can use the power button as a Sleep/Hibernate hot­key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound menu) control panel in Windows Vista to configure this fea­ture.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press the pow­er button for 4 seconds, or longer, to force the system to turn itself off.
Power Button Sleep
Sleep is the default power mode when the power button is pressed for less than 4 seconds. You may configure the options for the power button from the Power Options (Hardware and Sound menu) control panel in Windows Vista (see your OS’s documentation, or
“Configuring the Power Buttons” on page 3 - 8 for details).
Power Management
Shut Down
Note that you should al­ways shut your comput­er down by choosing the Shut Down command from the Lock Button
Menu in Windows Vis- ta. This will help prevent
hard disk or system problems.
3
Turning on the Computer 3 - 3
Power Management

Power Plans

3
Resuming Operation
If the display is off the system can resume by pressing any key on the keyboard.
The system can resume from Sleep mode by pressing the Sleep But-
ton key combination (Fn + F4), or power button.
Password
It is recommended that you enable a password on system resume in or­der to protect your data.
The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.
The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.
Click Change plan settings and then click Change advanced power settings to ac­cess further configuration options in Advanced Settings.
Figure 3 - 1
Power Plan
Advanced Settings
3 - 4 Power Plans
Each Windows power plan will also adjust the processor performance of your ma­chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).
Choose High performance for maximum performance when the computer is pow­ered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) pow­ered.
Power Management
3
Figure 3 - 2
Power Plans
Power Plans3-5
Power Management

System Power Options

3
Sleep Button
The Sleep Button in the Start Menu (not available in Classic View) can be used to send the computer into Sleep.
Note that Sleep is the default power saving state in Windows Vista.
You can use the system power options to stop the computer’s operation and restart where you left off. The system features Sleep and Hibernate power saving states (Hibernate will need to be enabled from power plan Advanced Settings see Figure
3 - 1 on page 3 - 4).

Hibernate vs. Shut Down

Hibernate and Shut Down are the same in that the system is off and you need to press the power button to turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left off (what was on your desktop) without reopening the application(s) and file(s) you last used.
You can use either method depending on your needs.

Sleep vs. Hibernate

If you want to stay away from your work for just a while, you can put the system into
Sleep instead of in hibernation. It takes a longer time to wake up the system from Hibernate mode than from Sleep mode. Sleep will effectively act as Hibernate if
the computer battery becomes depleted (see “Sleep Mode & Mobile PC Battery” on
page 3 - 7).
3 - 6 System Power Options

Sleep

Sleep uses very little system power, and takes a short time to return to full operation. After an extended period of time in Sleep the computer will save the contents of sys- tem memory (e.g. any open documents and applications) to the hard disk and shut the system down. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep mode to save power.

Hibernate

Hibernate uses no power and saves all of your information on a part of the hard disk before it turns the system off. Although it saves the most power it takes the longest time to return to full operation. You can set your computer to automatically enter Hi-
bernate when the battery power is almost depleted. You will need to enable Hiber­nate mode from the Advanced Settings in power plans, or you put the system directly into Hibernate mode from the Lock Button Menu. The system will re­sume from Hibernate mode by pressing the power button.
Power Management
Sleep Mode &
Mobile PC Battery
A mobile PC in Sleep uses very little battery power.
After an extended peri­od of time the computer will save any open docu­ments and applications to hard disk.
Figure 3 - 3
Lock Button Menu
Hibernate
3
System Power Options 3 - 7
Power Management

Configuring the Power Buttons

3
Password Protection
It is recommended that you enable a password on wake up in order to protect your data.
However you can dis­able this setting from the Power Options menu by clicking Require a
password on wakeup
in the left menu, and se­lecting the options (click
Change settings that are currently unavail­able).
Figure 3 - 4
Power Options
Define Power
Buttons
The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the computer in to either Sleep or Hibernate. In Sleep, the LED will blink green. In Hibernate the LED will be off (battery) or orange (AC/DC adapter). If only the display is turned off, the LED will remain green.
3 - 8 Configuring the Power Buttons

Battery Information

Please follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the pro­grams you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Advanced Settings (see Figure 3 - 1 on page 3 - 4).
Click the battery icon in the taskbar to see the current battery level and charge status.
Power Management
Low Battery
Warning
When the battery is criti­cally low, immediately connect the AC/DC adapter to the computer or save your work, oth­erwise, the unsaved data will be lost when the power is depleted.
Figure 3 - 5
Battery Icon
(Taskbar) & Battery
Advanced Settings
3
Battery Information 3 - 9
Power Management

Conserving Battery Power

3
Windows Mobility
Center
The Windows Mobility Center control panel pro-
vides an easy point of ac­cess for information on battery status, power plans used and wireless device status etc.
Figure 3 - 6
Windows Mobility
Center
•Use a power plan that conserves power (e.g Power saver), however note that
this may have an affect on computer performance.
Lower the brightness level of the LCD display. The system will decrease LCD
brightness slightly to save power when it is not powered by the AC/DC adapter.
Reduce the amount of time before the display is turned off.
Close wireless, Bluetooth, modem or co mmunication applications when they are
not being used.
Disconnect/remove any unnecessary external devices e.g. USB devices,
ExpressCards etc.
3 - 10 Conserving Battery Power

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.
We recommend that you do not remove the battery yourself. If you do need to re­move the battery for any reason see “Removing the Battery” on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”
on page 3 - 13 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to “LED Indica-
tors” on page 1 - 9 for information on the battery charge status, and to “Battery In­formation” on page 3 - 9 for more information on how to maintain and properly
recharge the battery pack.)
Power Management
3
Battery Life3-11
Power Management

Proper handling of the Battery Pack

3
Caution
Danger of explosion if battery is incorrectly re­placed.
DO NOT disassemble the battery pack under any circumstances
DO NOT expose the battery to fire or high temperatures, it may explode
DO NOT connect the metal terminals (+, -) to each other
Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s in­structions.
Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your service center. If the battery has bee n d roppe d we do not recommend using it any further, as even if the computer continues to work with a dam­aged battery in place, it may cause circuit damage, which may possibly result in fire . It is recommended that you replace your computer battery every two years.
Damaged Battery Warning
3 - 12 Battery Life

Battery FAQ

How do I completely discharge the battery?
Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
1. Save and close all files and applications.
2. Create a power plan for dischar ging the battery and set all the options to Never.
3. Click Change plan settings (after saving it) and click Change advanced power settings.
Power Management
3
Figure 3 - 7
Power Plan Create
Battery Life3-13
Power Management
4. Scroll down to Battery and click + to expand the battery options.
5. Choose the options below (click Yes if a warning appears):
3
Figure 3 - 8
Power Options
Advanced Settings -
Battery
Low battery levels = 0%
Critical battery Levels = 0%
Low battery action = Do Nothing
Critical battery action (On battery) = Shut Down
Critical battery action (Plugged in) = Do Nothing
3 - 14 Battery Life
How do I fully charge the battery?
When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.
How do I maintain the battery?
Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Power Management
3
Battery Life3-15
Power Management
3
3-16

Chapter 4: Drivers & Utilities

Drivers & Utilities
This chapter deals with installing the drivers and utili­ties essential to the operation or improvement of some of the computer’s subsystems. The system takes ad­vantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-config­ured with an appropriate driver or utility during oper­ating system installation. Instead, you need to manually install some system-required drivers and utilities.

What to Install

The Device Drivers & Utilities + User’s Manual CD­ROM (Win Vista OR WinXP) contains the drivers and
utilities necessary for the proper operation of the com­puter. There will be two CDs provided; one will con­tain drivers for Windows Vista, the other will contain drivers for Windows XP (make sure you install the ap­propriate drivers for your system).
Table 4 - 1, on page 4 - 3 lists what you need to install
and it is very important that the drivers are in- stalled in the order indicated.

Module Driver Installation

The procedures for installing drivers for the Wireless LAN, Bluetooth, and PC Camera modules are pro-
vided in “Modules & Options” on page 7 - 1.
4
What to Install 4 - 1
Drivers & Utilities

Driver Installation

Insert the Device Drivers & Utilities + User’s Manual CD-ROM and click Install Vista Drivers (button)/In-
stall Option Drivers (button).
4
If you wish to install the drivers manually see page 4 -
4
.
Figure 4 - 1 - Drivers Installer Screen 1
1. Check the driver installation order from Table 4 - 1,
on page 4 - 3 (the dri ve r s mus t be installed in
this order) which is the same as that listed in the
Drivers Installer menu below.
2. Click to select the driver you wish to install, after installing each driver it will become grayed out (if you need to reinstall any driver, click the Unlock button).
3. Follow the instructions for each individual driver installation procedure as listed on the following pages.
Figure 4 - 2 - Drivers Installer Screen 2
4 - 2 Driver Installation
Drivers & Utilities
Driver Page #
Video Page 4 - 5
Audio Page 4 - 5
Modem Page 4 - 6 LAN Page 4 - 6 TouchPad Page 4 - 6 CardReader Page 4 - 6 Hot Key Page 4 - 6 Wireless LAN Page 7 - 2 Bluetooth Page 7 - 7 PC Camera Page 7 - 11
Table 4 - 1 - Driver Installation

Updating/Reinstalling Individual Drivers

If you wish to update/reinstall individual drivers it may be necessary to uninstall the original driver.To do this go to the Control Panel in the Windows OS and double-click the Programs and Features icon (Pro- grams > Uninstall a program). Click to select the driver (if it is not listed see below) and click Uninstall, and then follow the on screen prompts (it may be nec­essary to restart the computer). Reinstall the driver as outlined in this chapter.
If the driver is not listed in the Programs and Fea- tures menu:
1. Click Start, and click Control Panel (or point to Settings and click Control Panel).
2. Double-click Device Manager (Hardware and Sound > Device Manager).
3. Double-click the device you wish to update/reinstall the driver for (you may need to click “+” to expand the selection).
4. Click Driver (tab) and click the Up date Driver or
Uninstall button and follow the on screen prompts.
4
Driver Installation 4 - 3
Drivers & Utilities

Manual Driver Installation

If you wish to install the drivers manually, click the Exit button to quit the Drivers Installer application, and then browse to the executable file in the location listed in the table below and follow the installation procedure for each driver. Note that X is the drive letter assigned to the CD/DVD-ROM drive.
.
4
Video Vista 32bit: X:\Drivers\01_Video\setup.exe Audio Vista 32bit: X:\Drivers\02_Audio\SETUP.EXE Modem Vista 32bit: X:\Drivers\03_Modem\ssetup.exe LAN Vista 32bit: X:\Drivers\04_LAN\setupvis.exe TouchPad Vista 32bit: X:\Drivers\05_Touchp ad\WinWDF\x86\dpinst.exe CardReader Vista 32bit: X:\Dri vers\06_CardReader\Setup.exe Hot Key Vista 32bit: X:\Drivers\07_Hotkey\1AP.exe
802.11 b/g USB WLAN Module Vista 32bit: X:\Drivers\Option\08_WLAN\Setup.exe Bluetooth Module Vista 32bit: X:\Drivers\Option\09_Bluetooth\setup.exe
Driver Driver Location
PC Camera Driver Installation
4 - 4 Driver Installation
Vista 32bit: X:\Drivers\Option\10_Camera\setup.exe (for non UVC Cameras) Vista 32bit: X:\Drivers\Option\11_UVC_Camera\setup.exe (for UVC Cameras)
Table 4 - 2 - Driver Location
Drivers & Utilities

User Account Control (Win Vista)

If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Allow, and follow the installation procedure as direct­ed.

Windows Security Message

If you receive a Windows security message as part of the driver installation process. Just click “Install this driver software anyway” or Install to continue the in­stallation procedure.
You will receive this message in cases where the driv­er has been released after the version of Windows you are currently using. All the drivers provided will have already received certification for Windows.

New Hardware Found

If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installa­tion procedure (other than when outlined in the driver install procedure), click Cancel to close the window, and follow the installation procedure as directed.

Driver Installation Procedure

Video

1. Click 1.Install Video Driver > Yes.
2. Click Next > Next.
3. Click Finish to restart the computer.

Audio

1. Click 2.Install Audio Driver > Yes.
2. Click Next.
3. Click the button to accept the license and click Next.
4. Click Next > Next > Next.
5. Click Finish to restart the computer.
4
Driver Installation 4 - 5
Drivers & Utilities

Modem

1. Click 3.Install Modem Driver > Yes.
2. Click OK.
3. The modem is ready for dial-up configuration.
4
Modem Country Selection
Go to the Phone and Modem Options control panel (Hardware and Sound) and make sure the modem country selection is appropriate for you.
LAN
1. Click 4.Install LAN Driver > Yes.
2. Click OK.
3. The network settings can mow be configured.

TouchPad

1. Click 5.Install Touchpad Driver > Yes.
2. Click Next.
3. Click Finish > Restart Now to restart the com­puter.
4. You may then configure your TouchPad as out­lined in “TouchPad and Buttons/Mouse” on
page 2 - 9.

CardReader

1. Click 6.Install CardReader Driver > Yes.
2. Click Next > Next.
3. Click Finish to restart the computer.

Hot Key

1. Click 7.Install Hotkey Driver > Yes.
2. Click Next.
3. Click Finish to restart the computer.
4 - 6 Driver Installation

Wireless LAN

See the introduction in “802.11 b/g USB WLAN Mod-
ule” on page 7 - 2, and check the installation proce-
dure.
Drivers & Utilities

Bluetooth

See the introduction in “Bluetooth Module” on
page 7 - 7, and check the installation procedure.

PC Camera

See the introduction in “Bluetooth Local Area Con-
nection” on page 7 - 9, and check the installation pro-
cedure.
4
Driver Installation 4 - 7
Drivers & Utilities
4
4-8
BIOS Utilities

Chapter 5: BIOS Utilities

Overview

This chapter gives a brief introduction to the computer’s built-in software:
The Setup utility If your computer has never been set up, or you are mak ing important chan ges to the system (e.g. hard disk setup), then you should review this chapter first and note the original settings found in Setup. Even if you are a beginner, keep a record of the set­tings you find and any changes you make. This information could be useful if your system ever needs servicing.
There is one general rule: Don’t make any changes unless you are sure of what you are doing. Many of the settings are required by the system, and changing them could cause it to become unstable or worse. If you have any doubts, consult your service representative.
BIOS Settings
Warning
Incorrect settings can cause your system to malfunction. To correct mistakes, return to Set-
up and restore the Set­up Defaults with <F9>.
5
Overview 5 - 1
BIOS Utilities

Startup Screen

Each time you turn on the computer, the system takes a few seconds to conduct tests on memory, keyboard, mouse and system. As the boot proceeds, you can click the mouse, or press Enter, and then choose “Launch System Setup” from the Trusted- Core menu to access the PhoenixBIOS Setup Utility.
Figure 5 - 1
5
Startup Screen
5 - 2 Startup Screen
In addition to accessing the Setup menus, you can also select a boot device, view
S
e
u
y
y
system information or setup a password for access to the computer at boot time (see overleaf).
BIOS Utilities
Launch System Setup
Continue Booting
TrustedCore
Dvi
r
lmnt
Figure 5 - 2
Trusted Core Menu
5
Startup Screen 5 - 3
BIOS Utilities
yup
y
m
w
N
m
p

Setting a Boot Password

1. Use the mouse to select Security Enrollment from the menu. A Security Enroll- ment screen similar to the screen below will then appear:
Figure 5 - 3
Security Enrollment
5
Password Warning
If you set a boot pass­word NEVER forget your password.
The consequences of this could be serious. If you cannot remember your boot password you must contact your ven­dor and you may lose all of the information on your hard disk.
5 - 4 Startup Screen
S
s
i
s
2. Type in the New Password, and then type it again to Confirm the new password.
3. Click OK to set the password.
4. You will now be prompted to enter the password when the computer boots up.
Note: To clear existing passwords follow the procedure above to bring up the Secu­rity Enrollment screen and type the existing password. Press Enter (without typing any password entry) and click Yes to un-enroll.

Setup Screens

The following pages contain additional advice on portions of the Setup.
Along the top of the screen is a menu bar with four (4) menu headings. When you select a heading, a new screen appears. Scroll through the features listed on each screen to make changes to Setup.
Instructions on how to navigate each screen are in the box along the bottom of the screen. If these tools are confusing, press F1 to call up a General Help screen, and then use the arrow keys to scroll up or down the page.
The Item Specific Help on the right side of each screen explains the highlighted item and has useful messages about its options.
If you see an arrow next to an item, press Enter to go to a sub-menu on that sub­ject. The sub-menu screen that appears has a similar layout, but the Enter key may execute a command.
BIOS Utilities
Setup Menus
The Setup menus shown in this section are for reference only. Your computer’s menus will indicate the configura­tion appropriate for your model and options.
5
Startup Screen 5 - 5
BIOS Utilities

Main Menu

Figure 5 - 4
Main Menu
5
Main
Main Advanced Boot Exit
System Time: [22:11:05]
System Date: [01/10/2007]
IDE Channel 0 Master [TSSTcorpCD/DVDW TS-L632D-]IDE Channel 2 Master [FUJITSU MHW2060BH-(S1)]
System Memory 633 KB
Extended Memory 894 MB
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
PhoenixBIOS Setup Utility
06
Item Specific Help
<Tab>, <Shift Tab>, or <Enter> selects field.

System Time & Date (Main Menu)

The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings. Some applications may also alter data files to reflect these changes.
5-6Main Menu

IDE Channel 0/2 Master (Main Menu)

Pressing Enter opens the sub-menu to show the configuration of either a DVD/CD Device or HDD on the computer’s IDE Channels. Use the Auto (Type:) setting to have the items configured automatically for you.

System/Extended Memory: (Main Menu)

This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
BIOS Utilities
5
Main Menu 5 - 7
BIOS Utilities

Advanced Menu

Figure 5 - 5
Advanced Menu
5
Main Advanced Boot Exit
Installed O/S: [WinXP/Vista]
Legacy USB Support: [Enabled] Reset Configuration Data: [No] Enable Multimedia Timer: [No] Frame Buffer Size: [128MB]
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
Advanced
PhoenixBIOS Setup Utility
Item Specific Help
Select the operating system installed on your system which you will use most commonly.
Note: An incorrect setting can cause some operating systems to display unexpected behavior.

Installed O/S: (Advanced Menu)

This setting tells the computer what kind of operating system you’re using.
5 - 8 Advanced Menu

Legacy USB Support: (Advanced Menu)

Choose “Enabled” if you intend to use USB devices in systems which do not nor­mally support USB functionality (e.g. DOS). The default setting is “Enabled” and does not need to be changed if you intend to use your USB devices in Windows.

Reset Configuration Data: (Advanced Menu)

This item is set to No as default. You can change the setting to Yes if you have in­stalled a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.

Enable Multimedia Timer: (Advanced Menu)

Multimedia timer services allow applications to schedule timer events with the greatest resolution (or accuracy) possible for the hardware platform. These timer ser­vices are useful for applications that demand high-resolution timing (see your appli­cation manual for further details). This item is set to Disabled as default.

Frame Buffer Size: (Advanced Menu)

Use this menu item to set the amount of system memory to be allocated for use by the integrated graphic system. The default memory size allocated is 128MB, and this may be adjusted to 64MB or 256MB if required.
BIOS Utilities
5
Advanced Menu 5 - 9
BIOS Utilities

Boot Menu

Figure 5 - 6
Boot Menu
5
Main Advanced Boot Exit
Boot priority order:
1: IDE 0: TSSTcorpCD/DVDW TS-L632D-(
2: IDE 4: FUJITSU MHW2060BH-(S1) 3: USB FDC: 4: USB KEY: 5: USB HDD: 6: PCI BEV: VIA Boot Agent 7: 8:
Excluded from boot order:
: USB CDROM: : USB ZIP : USB LS120 : PCI SCSI
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Select Sub-Menu F10 Save and Exit
PhoenixBIOS Setup Utility
Item Specific Help
Keys used to view or configure devices: Up and Down arrows select a device. <+> and <-> moves the device up or down. <x> exclude or include the device to boot. <Shift +1> enables or disables a device. <1 - 4> Loads default boot sequence.
When you turn the computer on it will look for an operating system (e.g. Win­dowsXP) from the devices listed in this menu, and in this priority order. If it cannot
find the operating system on that device, it will try to load it from the next device in the order specified in the Boot priority order. Item specific help on the right is available to help you move devices up and down the order.
5 - 10 Boot Menu

Exit Menu

BIOS Utilities
PhoenixBIOS Setup Utility
Main Advanced Security Boot Exit
Exit Saving Changes
Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes
F1 Help  Select Item -/+ Change Values F9 Setup Defaults Esc Exit  Select Menu Enter Execute Command F10 Save and Exit
Exit
Item Specific Help
Exit System Setup and save your changes to CMOS.
Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Set- up defaults that will return the Setup to its original state, and erase any previous changes you have made in a previous session.
Figure 5 - 7
Exit Menu
5
Exit Menu 5 - 11
BIOS Utilities
5
5-12
Upgrading The Computer

Chapter 6: Upgrading The Computer

Overview

This chapter contains information on upgrading the computer. Follow the steps out­lined to make the desired upgrades. If you have any trouble or problems you can con­tact your service representative for further help. Before you begin you will need:
A small crosshead or Phillips screwdriver
A small regular slotted (flathead) screwdriver
An antistatic wrist strap Before working with the internal components you will need to wear an antistatic
wrist strap to ground yourself because static electricity may damage the compo­nents.
The chapter includes:
Removing the Battery
Upgrading the Hard Disk Drive
Upgrading the Optical (CD/DVD) Device
Upgrading the System Memory (RAM)
Please make sure that you review each procedure before you perform it.
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
6
Note
Note that the disassem­bly pictures are correct at time of going to press. However computer de­signs are subject to con­tinual updates and changes, and some models may appear slightly different from those pictured.
Overview 6 - 1
Upgrading The Computer

When Not to Upgrade

Power Safety
Warning
Before you undertake any upgrade proce­dures, make sure that you have turned off the power, and disconnect-
6
ed all peripherals and cables (including tele­phone lines). It is advis­able to also remove your battery in order to pre­vent accidentally turning the machine on.
These procedures involve opening the system’s case, adding and sometimes replac­ing parts.
You should not perform any of these upgrades if:
Your system is still under warranty or a service contract
You don’t have all the necessary equipment
You’re not in the correct environment
You doubt your abilities
Under any of these conditions, contact your service representative to purchase or re­place the component(s).
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s) and screw(s) before turning the computer on.
6 - 2 Overview
Upgrading The Computer

Removing the Battery

If you are confident in undertaking upgrade procedures yourself, for safety reasons it is best to remove the battery.
1. Turn the computer off, and turn it over.
2. Slide the latch in the direction of the arrow, and hold it in place.
3. Slide the battery in the direction of the arrow .
1
Model A
2
1 1
Model B
2
Warranty Warning
Please check with your service representative before undertaking any upgrade procedures to find out if this will VOID your warranty.
6
Figure 6 - 1
Battery Latch
1
Removing the Battery 6 - 3
Upgrading The Computer
4. Lift the battery out in the direction of the arrow .
3
Figure 6 - 2
Battery Up
3
6
5. Lift the battery out.
Figure 6 - 3
Battery Out
4
4
6 - 4 Removing the Battery
Upgrading The Computer

Upgrading the Hard Disk Drive

The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow your operating system’s installation instructions, and install all necessary drivers and util­ities (as outlined in “Driver Installation” on page 4 - 2), when setting up a new hard disk.
1. Turn off the computer, and turn it over and remove the battery.
2. Locate the hard disk bay cover and remove screw (Model A) or screws &
3
(Model B).
Model A Model B
1
1 2
32
HDD System
Warning
New HDD’s are blank. Be­fore you begin make sure: You have backed up any data you want to keep from your old HDD. You have all the CD-ROMs and FDDs required to in­stall your operating system and programs. If you have access to the in­ternet, download the latest application and hardware driver updates for the oper­ating system you plan to in­stall. Copy these to a removable medium.
Figure 6 - 4
Hard Disk Bay &
Screw(s)
6
Upgrading the Hard Disk Drive 6 - 5
Upgrading The Computer
For Model A computers:
3. Slide the hard disk and cover assembly in the direction of arrow .
4. Lift the hard disk and cover assembly up in the direction of arrow .
5. Remove the ha rd di sk and cover assembly .
4
5
6
Figure 6 - 5
HDD & Cover
Assembly
6
Removal (Model A
Computers Only)
6 - 6 Upgrading the Hard Disk Drive
Model A
4
5
6
Upgrading The Computer
6. Remove the scr ews - to release the hard disk from the assembly cover
12
, and reverse the process to install any new hard disk.
7 10 11
10
9
Model A
12
7
8
11
Figure 6 - 6
HDD Assembly Cover Removal
(Model A
Computers Only)
6
Upgrading the Hard Disk Drive 6 - 7
Upgrading The Computer
For Model B computers:
7. Remove the cover .
8. Pull the tab to slide the hard disk and case asse mbly in th e dir ect ion of arro w
9. Lift the hard disk and case assembly out of the bay in the direction of arrow .
10. Remove screws & to release the hard disk from the case , and reverse the process to install any new hard disk.
6
Figure 6 - 7
HDD & Case
Assembly
Removal (Model B
Computers Only)
7
Model B
7
10 11 12 13
8
13
10
9
12
11
8
.
9
6 - 8 Upgrading the Hard Disk Drive

Upgrading the Optical (CD/DVD) Device

1. Turn off the computer, and turn it over and remove the battery.
2. Remove screws component bay cover .
1 7 1 5
- (Model A)/ - (Model B), and remove the
8
Upgrading The Computer
Model A
3 4
2
1
5
7
8
6
Model B
2 3
1
5
4
6
Figure 6 - 8
Removing the
Component Bay
Cover
8
Upgrading the Optical (CD/DVD) Device 6 - 9
Upgrading The Computer
3. Use a screwdriver to carefully push out the optical device at point .
4. Reverse the process to install the new device.
9
6
9
Figure 6 - 9
Removing the
Optical (CD/DVD)
Device
6 - 10 Upgrading the Optical (CD/DVD) Device
Upgrading The Computer

Upgrading the System Memory (RAM)

Model A computers have TWO memory sockets (Model B computers have ONE memory socket) for 200 pin Small Outline Dual In-line (SO-DIMM) DDR2 (DDRII) type memory modules (see “Memory” on page C - 2 for details of support- ed module types).
1. Turn off the computer, and turn it over and remove the battery.
2. Remove screws component bay cover .
1 7 1 5
- (Model A)/ - (Model B), and remove the
8
6
Model A
Model B
3
2
1
4
5
67
8
1
2
3
Figure 6 - 10
5
4
8
Removing the
Component Bay
Cover
Upgrading the System Memory (RAM) 6 - 11
Upgrading The Computer
3. Locate the RAM socket(s) .
9
Model A (2 RAM Sockets) Model B (1 RAM Socket)
Figure 6 - 11
RAM Socket
Location
9
6
4. Gently pull the two release latches on the sides of the memory socket in the
10 11
direction indicated by the arrows ( &
).
9
Model A (2 RAM Sockets) Model B (1 RAM Socket)
Figure 6 - 12
RAM Socket
Release Latches
10
11
10
11
6 - 12 Upgrading the System Memory (RAM)
Upgrading The Computer
5. The RAM module will pop-up, and you can remove it.
Model A (2 RAM Sockets)
6. Pull the latches to release the second module (Model A only) if necessary.
7. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.
8. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE the module; it should fit without much pressure.
9. Press the module in and down towards the mainboard until the slot levers click into place to secure the module.
10. Replace the component bay cover and screws.
11. Restart the computer to allow the BIOS to register the new memory configuration as it starts up.
11
Model B (1 RAM Socket)
111111
Contact Warning
Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.
Figure 6 - 13
RAM Module
Removal
6
Upgrading the System Memory (RAM) 6 - 13
Upgrading The Computer

Upgrading the Processor

Warranty
The CPU is not a user serviceable part. Open­ing this compartment, or accessing the CPU in any way, may violate your warranty.
6
Unauthorized tampering with the HDD may also violate your warranty.
If you want to upgrade your computer by replacing the existing processor with a fast­er/new one you will need to contact your customer service representative. We rec­ommend that you do not do this yourself, since if it is done incorrectly you may damage the processor or mainboard.
6-14
Loading...