Clevo M350H, M360H, M362H, M363H Service Manual

Download

Page 1

Page 2

Page 3

Notebook Computer M350H/ M360H/ M362H/ M363H

Service Manual

Preface

Page 4

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.

This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.

Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer.

Version 1.0 December 2004

Trademarks

Intel® and Pentium® are registered trademarks of Intel Corporation. Windows® is a registered trademark of Microsoft Corporation.

Other brand and product names are trademarks and./or registered trademarks of their respective companies.

Page 5

About this Manual

This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and inspection of personal computers.

It is organized to allow you to look up basic information for servicing and/or upgrading components of the M350H/ M360H/ M362H/ M363H series notebook PC.

The following information is included:

Chapter 1, Introduction, provides general information about the location of system elements and their specifications. Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems and how to upgrade elements of the system.

Preface

Appendix A, Part Lists Appendix B, Schematic Diagrams

Preface

III

Page 6

Preface

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 3.25A).

CAUTION

Preface

Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.

TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,

TELECOMMUNICATION LINE CORD

This computer’s optical device is a Class I Laser product.

Page 7

Instructions for Care and Operation

The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

Preface

Do not expose the computer to any shock or vibration.

Do not place it on an unstable surface.

Do not place anything heavy on the computer.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

Do not expose it to excessive heat or direct sunlight.

Do not leave it in a place where foreign matter or moisture may affect the system.

Don’t use or store the computer in a humid environment.

Do not place the computer on any surface which will block the vents.

3. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work. Remember to periodically save your data as data may be lost if the battery is depleted.

Do not turn off the power until you properly shut down all programs.

Do not turn off any peripheral devices when the computer is on.

Do not disassemble the computer by yourself.

Perform routine maintenance on your computer.

Preface

Page 8

Preface

4. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong mag- netic fields. These can hinder proper performance and damage your data.

5. Take care when using peripheral devices.

Preface



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines). It is advisable to also remove your battery in order to prevent accidentally turning the machine on.

Use only approved brands of peripherals.

Unplug the power cord before attaching peripheral devices.

Power Safety

The computer has specific power requirements:

• Only use a power adapter approved for use with this computer.

• Your AC adapter may be designed for international travel but it still requires a steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.

• The power adapter may have either a 2-prong or a 3-prong grounded plug. The third prong is an important safety feature; do not defeat its purpose. If you do not have access to a compatible outlet, have a qualified electrician install one.

• When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.

• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.

• Before cleaning the computer, make sure it is disconnected from any external power supplies.

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Page 9

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative or qualified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteries may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.



Battery Disposal

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Caution

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Preface

VII

Page 10

Preface

1: Introduction

Overview

This manual covers the information you need to service or upgrade the M350H/ M360H/ M362H/ M363H series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information about drivers (e.g. VGA & audio) is also found in User’s Manual. That manual is shipped with the computer.

Operating systems (e.g. DOS, Windows 9x, Windows NT 4.0, Windows 2000, Windows XP, OS/2 Warp, UNIX, etc.) have their own manuals as do application software (e.g. word processing and database programs). If you have questions about those programs, you should consult those manuals.

The M350H/ M360H/ M362H/ M363H series notebook is designed to be upgradeable. See “Disassembly” on page 2 -

1 for a detailed description of the upgrade procedures for each specific component. Please note the warning and safety

information indicated by the “” symbol.

The balance of this chapter reviews the computer’s technical specifications and features.

Introduction

1.Introduction

Overview 1 - 1

Page 14

Introduction

System Specifications



Latest Specification Information

The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/speeds) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.

Feature Specifications

1.Introduction

1 - 2 System Specifications

Processor Types

Core Logic

Structure

Security

Intel Pentium® M - (478-pin) Micro-FCPGA package

Intel Celeron® M - (478-pin) Micro-FCPGA package

Intel 852GM + 82801 DBM ICH4-M

PC2001 Compliant PCI 2.2 Compliant

Security (Kensington® Type) Lock Slot BIOS Password

(

µ0.13) 0.13 Micron Process Technology, 1MB

On-die L2 Cache & 400MHz FSB -

1.3/ 1.4/ 1.5/ 1.6/ 1.7 GHz

(

µ0.09) 0.09 Micron Process Technology, 2MB

On-die L2 Cache & 400MHz FSB 715/ 725/ 735 (1.5 ~ 1.7 GHz)

(

µ0.13) 0.13 Micron Process Technology, 512KB

On-die L2 Cache & 400MHz FSB - 320/ 330/ 340 (1.3 ~ 1.5 GHz)

(

µ0.09) 0.09 Micron Process Technology, 1MB

On-die L2 Cache & 400MHz FSB 350/ 360/ 370 (1.3 ~ 1.5 GHz)

ACPI 2.0 Compliant

Page 15

Feature Specifications

Introduction

Memory

BIOS

LCD

Display

Storage

Audio

Keyboard & Pointing Device

PCMCIA

Interface

Two 200-pin SODIMM sockets, supporting 266 MHz DDR modules

Memory expandable up to 2GB (128/ 256/ 512/ 1024 MB DDR modules)

One 512KB Flash ROM Insyde BIOS, Plug and Play (1.0a)

14.1" XGA Flat Panel TFT (1024*768)

Dynamic Video Memory Technology (Shared Memory up to 64MB)

Fully DirectX 7/8 Compliant Graphics Engine Supports VESA DDCI, DDC2 Specifications

High quality 2D/3D Graphics Engine

One changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive Easy changeable 2.5" 9.5 mm (h) HDD

Supports Master Mode IDE Supports PIO Mode 4

AC’97 2.2 Compliant Advanced Wavetable Synthesizer DirectSound™ 3D Accelerator

Full-Duplex Built-In Microphone 2 Built-In Speakers

A4 Size Keyboard Built-In TouchPad with Scrolling Function

One Type-II PCMCIA 3.3V/5V Socket

Two USB 2.0/1.1 Ports One External VGA Monitor Port One Headphone-Out Jack One Microphone-In Jack

One S/PDIF Output Jack One RJ-11 Jack for Plug & Play Fax/Modem One RJ-45 Jack for 100M (Max) Fast Ethernet One DC-in Jack

1.Introduction

Communication

56K Plug & Play Fax/Modem V.90/92 Compliant 100M (Max) Fast Ethernet (IEEE 802.3 and

802.3u Standard Compliant)

PC Camera with USB Interface (optional) Bluetooth & MDC Modem Combo Module (optional)

(802.11b/g) Mini PCI WLAN Module (optional)

System Specifications 1 - 3

Page 16

Introduction

Feature Specifications

1.Introduction

Power Management

Power

Environmental Spec

Physical Dimensions & Weight

Optional

Supports ACPI 2.0 Power Button as Sleep/Resume Key Supports Hibernate Mode Supports Standby Mode

Full Range AC Adapter

AC-Input 100~240V, 47~63Hz

DC Output 20V, 3.25A (65W) One 4 cell, 32 Watt, Smart Lithium-Ion Battery Pack - Approx 2 Hours battery life One 6 cell, 48 Watt, Smart Lithium-Ion Battery Pack (optional) - Approx 3 Hours battery life

Temperature

Operating: 5

Non-Operating: -20°C ~ 60°C

312mm (w) * 263mm (d) * 27.5mm (h) Min 2.2 kg without Battery

Bluetooth & MDC Modem Combo Module 6 cell, 48 Watt, Smart Lithium-Ion Battery Pack Approx 3 Hours battery life

°C ~ 35°C

Supports Battery Low Sleep Mode Supports Resume From Modem Ring Supports Wake on LAN

Relative Humidity

Operating: 20% ~ 80% Non-Operating: 10% ~ 90%

PC Camera with USB Interface (802.11b/g) Mini PCI WLAN Module Software DVD Player

1 - 4 System Specifications

Page 17

Design Differences

This manual refers to the two notebook designs pictured below. The designs vary slightly in external design. Photographs used throughout this manual are of Design I. In addition to the basic designs, there are also two colored (red and blue) gloss style top cover designs. See Figure 2 for an illustration. Note the specific care instructions for this type of cover.

Introduction

Figure 1

Design Differences

1.Introduction

Design I

Design II

System Specifications 1 - 5

Page 18

Introduction

Figure 2

Gloss Style Top

Cover

1.Introduction

Gloss Style Top Cover Designs

There are two colored (red and blue) gloss style top cover designs incorporated within the design styles of this notebook model. Note the following guidelines for care and attention of this type of top cover.

• Remove the protective cover slowly and carefully. Do not forcibly tear off the protective cover as this may damage the surface of the top cover.

• Do not use pointed objects on the surface of the top cover, and do not place objects on top of it.

• Do not expose the top cover to excessive heat or direct sunlight.

• Only use the soft cloth provided for cleaning the top cover, and do not use abrasive cleaners.

1 - 6 System Specifications

Page 19

Introduction

External Locator - Top View

4 4

Figure 3

Top View

1. Optional Built-In PC Camera

2. LCD

3. LED Power & Communication Indicators

4. Speakers

5. Lid Sensor

6. LED Status Indicators

7. Power Button

8. Keyboard

9. Built-In Microphone

10. TouchPad and Buttons

1.Introduction

External Locator - Top View 1 - 7

Page 20

Introduction

Figure 4

Front View

1. LCD Latches

2. Hot-Key Buttons

Figure 5

Left Side View

1.Introduction

1. Vent

2. External Monitor (CRT) Port

3. RJ-11 Phone Jack

4. RJ-45 LAN Jack

5. 2 * USB 2.0 Ports

6. PC Card Slot Eject Button

7. PC Card Slot

External Locator - Front & Left Side Views

2 3 4 5

1 - 8 External Locator - Front & Left Side Views

Page 21

External Locator - Right Side & Rear Views

Introduction

Figure 6

Right Side View

1 2 3

1. Microphone-In Jack

2. Headphone-Out Jack

3. S/P DIF Output Jack

4. Optical Device Bay

5. DC-In Jack

1.Introduction

Figure 7

Rear View

1. Security Lock Slot

2. Vent

External Locator - Right Side & Rear Views 1 - 9

Page 22

Introduction

Figure 8

Bottom View

External Locator - Bottom View

1. Vent/Fan Intakes

2. Battery

3. CPU Cover

4. RAM & WLAN Module Cover

5. Optical Device Screw Cover

6. Hard Disk Module Cover

1.Introduction

1 - 10 External Locator - Bottom View

Page 23

Introduction

Mainboard Overview - Top (Key Parts)

Figure 9

Mainboard Top

Key Parts

1. PC Card Assembly

2. Southbridge Intel 82801DB

3. Northbridge Intel 82852GM

4. H8 Keyboard Controller

1.Introduction

Mainboard Overview - Top (Key Parts) 1 - 11

Page 24

Introduction

Figure 10

Mainboard Bottom

Key Parts

1. Memory Sockets (no memory installed)

2. CPU Socket (no CPU installed)

3. Clock Generator

4. BIOS EEPROM

5. LAN Transformer

6. CardBus ENE 1410

7. ALC202 - Audio Codec

8. Audio Amplifier

1.Introduction

Mainboard Overview - Bottom (Key Parts)

1 - 12 Mainboard Overview - Bottom (Key Parts)

Page 25

Introduction

Mainboard Overview - Top (Connectors)

Figure 11

Mainboard Top

Connectors

1. TouchPad Cable Connector (JTP1)

2. Keyboard Connector (JKB1)

1.Introduction

Mainboard Overview - Top (Connectors) 1 - 13

Page 26

Introduction

Figure 12

Mainboard Bottom

Connectors

1. Battery Connector (JBATT1)

2. RTC (JBAT1)

3. Power Cable Connector (JPWR1)

4. Multi-function Board Cable Connector (JMFC1)

5. CD-ROM Connector (JCD1)

6. Hard Disk Connector (JHDD1)

7. Audio Board Cable Connector (JAUDIO1)

8. Int. MIC (JMIC1)

9. USB Connector (JUSB1 & JUSB2)

10. Int. Speaker Cable

1.Introduction

Connector (JSPK2)

11. Int. Speaker Cable Connector (JSPK1)

12. LAN Connector (JMLAN1)

13. Modem Cable Connector (JMODEM1)

14. TV-Out Connector (JSVIDEO1)

15. Inverter Connector (JINV1)

16. VGA-Out Connector (JVGA1)

17. LCD (LVDS) Connector (JLCD1)

18. Modem Connector (JMDC1)

19. Fan Cable Connector (JFAN1)

Mainboard Overview - Bottom (Connectors)

7 8

1 - 14 Mainboard Overview - Bottom (Connectors)

Page 27

2: Disassembly

Overview

This chapter provides step-by-step instructions for disassembling the M350H/ M360H/ M362H/ M363H series notebook’s parts and subsystems. When it comes to reassembly, reverse the procedures (unless otherwise indicated).

We suggest you completely review any procedure before you take the computer apart.

Disassembly

Procedures such as upgrading/replacing the RAM, optical device and hard disk are included in the User’s Manual but are repeated here for your convenience.

To make the disassembly process easier each section may have a box in the page margin. Information contained under

the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a 

lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the disassembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previous disassembly procedure. The amount of screws you should be left with will be listed here also.

A box with a  will also provide any possible helpful information. A box with a  contains warnings.

An example of these types of boxes are shown in the sidebar.

2.Disassembly



Information



Warning

Overview 2 - 1

Page 28

Disassembly

2.Disassembly

NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the battery is removed too).

Maintenance Tools

The following tools are recommended when working on the notebook PC:

• M3 Philips-head screwdriver

• M2.5 Philips-head screwdriver (magnetized)

• M2 Philips-head screwdriver

• Small flat-head screwdriver

• Pair of needle-nose pliers

• Anti-static wrist-strap

Connections

Connections within the computer are one of four types:

Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to

gently pry the locking collar away from its base. When replacing the connection, make sure the connector is oriented in the same way. The pin1 side is usually not indicated.

2 - 2 Overview

Pressure sockets for multi-wire connectors To release this connector type, grasp it at its head and gently

rock it from side to side as you pull it out. Do not pull on the wires themselves. When replacing the connection, do not try to force it. The socket only fits one way.

Pressure sockets for ribbon connectors To release these connectors, use a small pair of needle-nose pli-

ers to gently lift the connector away from its socket. When replacing the connection, make sure the connector is oriented in the same way. The pin1 side is usually not indicated.

Board-to-board or multi-pin sockets To separate the boards, gently rock them from side to side as

you pull them apart. If the connection is very tight, use a small flat-head screwdriver - use just enough force to start.

Page 29

Maintenance Precautions

The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions:

1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other components could be damaged.

2. Don't overheat it. Note the proximity of any heating elements. Keep the computer out of direct sunlight.

3. Avoid interference. Note the proximity of any high capacity transformers, electric motors, and other strong mag- netic fields. These can hinder proper performance and damage components and/or data. You should also monitor the position of magnetized tools (i.e. screwdrivers).

4. Keep it dry. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

5. Be careful with power. Avoid accidental shocks, discharges or explosions.

•Before removing or servicing any part from the computer, turn the computer off and detach any power supplies.

•When you want to unplug the power cord or any cable/wire, be sure to disconnect it by the plug head. Do not pull on the wire.

6. Peripherals – Turn off and detach any peripherals.

7. Beware of static discharge. ICs, such as the CPU and main support chips, are vulnerable to static electricity. Before handling any part in the computer, discharge any static electricity inside the computer. When handling a printed circuit board, do not use gloves or other materials which allow static electricity buildup. We suggest that you use an anti-static wrist strap instead.

8. Beware of corrosion. As you perform your job, avoid touching any connector leads. Even the cleanest hands produce oils which can attract corrosive elements.

9. Keep your work environment clean. Tobacco smoke, dust or other air-born particulate matter is often attracted to charged surfaces, reducing performance.

10. Keep track of the components. When removing or replacing any part, be careful not to leave small parts, such as screws, loose inside the computer.

Disassembly



Power Safety

Warning

2.Disassembly

Cleaning

Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Overview 2 - 3

Page 30

Disassembly

Disassembly Steps

The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM THE DISASSEMBLY STEPS IN THE ORDER INDICATED.

2.Disassembly

To remove the Battery:

1. Remove the battery page 2 - 7

To remove the HDD:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

To remove the System Memory:

1. Remove the battery page 2 - 7

2. Remove the system memory page 2 - 10

To remove the Optical Device:

1. Remove the battery page 2 - 7

2. Remove the optical device page 2 - 12

To remove the Processor:

1. Remove the battery page 2 - 7

2. Remove the processor page 2 - 13

To remove the Keyboard:

1. Remove the battery page 2 - 7

2. Remove the keyboard page 2 - 15

To remove the Wireless LAN:

1. Remove the battery page 2 - 7

2. Remove the processor page 2 - 13

3. Remove the wireless LAN page 2 - 16

To remove the Bottom Case:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the system memory page 2 - 10

4. Remove the optical device page 2 - 12

5. Remove the processor page 2 - 13

6. Remove the bottom case page 2 - 17

To remove the Modem:

1. Remove the battery page 2 - 7

2. Remove the bottom case page 2 - 17

3. Remove the modem page 2 - 18

To remove the Audioboard:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the optical device page 2 - 12

4. Remove the processor page 2 - 13

5. Remove the bottom case page 2 - 17

6. Remove the audioboard page 2 - 19

2 - 4 Disassembly Steps

Page 31

Disassembly

To remove the Multi-function board:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the optical device page 2 - 12

4. Remove the processor page 2 - 13

5. Remove the bottom case page 2 - 17

6. Remove the multi-function board page 2 - 20

To remove the Mainboard:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the system memory page 2 - 10

4. Remove the optical device page 2 - 12

5. Remove the modem page 2 - 18

6. Remove the processor page 2 - 13

7. Remove the keyboard page 2 - 15

8. Remove the bottom case page 2 - 17

9. Remove the audioboard page 2 - 19

10. Remove the multi-function board page 2 - 20

11. Remove the mainboard page 2 - 21

To remove the TouchPad & Click Board:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the system memory page 2 - 10

4. Remove the optical device page 2 - 12

5. Remove the modem page 2 - 18

6. Remove the processor page 2 - 13

7. Remove the keyboard page 2 - 15

8. Remove the bottom case page 2 - 17

9. Remove the audioboard page 2 - 19

10. Remove the multi-function board page 2 - 20

11. Remove the mainboard page 2 - 21

12. Remove the touchpad & click board page 2 - 22

To remove the Inverter:

1. Remove the battery page 2 - 7

2. Remove the inverter page 2 - 23

To remove the Speakers:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the optical device page 2 - 12

4. Remove the processor page 2 - 13

5. Remove the bottom case page 2 - 17

6. Remove the multi-function board page 2 - 20

7. Remove the mainboard page 2 - 21

8. Remove the inverter page 2 - 23

9. Remove the speakers page 2 - 24

2.Disassembly

Disassembly Steps 2 - 5

Page 32

Disassembly

2.Disassembly

To remove the LCD Panel:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the optical device page 2 - 12

4. Remove the processor page 2 - 13

5. Remove the bottom case page 2 - 17

6. Remove the multi-function board page 2 - 20

7. Remove the inverter page 2 - 23

8. Remove the LCD panel page 2 - 25

To remove the PC Camera:

1. Remove the battery page 2 - 7

2. Remove the inverter page 2 - 23

3. Remove the PC Camera page 2 - 25

2 - 6 Disassembly Steps

Page 33

Removing the Battery

1. Turn the computer off, and turn it over.

2. Locate the battery bay at point

3. Slide the battery lock in the direction of the arrow (towards the unlock symbol ), and hold it in place (Figure

1b).

4. Slide the Battery

out of the computer’s battery bay (Figure 1c).

(Figure 1a).

Disassembly

Figure 1

Battery Removal

a. Locate the battery re-

lease latch.

b. Slide the battery lock to

the left and hold.

c. Slide the battery out.

2.Disassembly



3. Battery

Removing the Battery 2 - 7

Page 34

Disassembly

Removing the Hard Disk Drive

Figure 2

HDD Assembly

Removal

a. Remove the 2 screws. b. Remove the cover.

2.Disassembly

The hard disk drive is mounted in a removable case and can be taken out to accommodate other 2.5" IDE hard disk drives with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.

Hard Disk Upgrade Process

1. Turn off the computer, turn it over and remove the battery (page 2 - 7).

2. Remove screws

1 2 3

& (Figure 2a) from the hard disk cover, and remove the cover .

a. b.



HDD System Warning

New HDD’s are blank. Before you begin make sure:

You have backed up any data you want to keep from your old HDD.

You have all the CD-ROMs and FDDs required to install your operating system and programs.

If you have access to the



3. Hard Disk Cover

•2 Screws

internet, download the latest application and hardware driver updates for the operating system you plan to install. Copy these to a removable medium.

2 - 8 Removing the Hard Disk Drive

Page 35

Disassembly

3. Pull the tab to slide the hard disk assembly in the direction of the arrow (Figure 3a).

4. Lift the hard disk assembly up out off the computer

5. Remove screws - , and separate the hard disk cover from the hard disk (Figure 3c).

1 2

4 7 8 9

(Figure 3b).

6. Reverse the process to install a new hard disk.

Figure 3

HDD Assembly

Removal (Cont.)

a. Slide out the HDD as-

sembly.

b. Lift the HDD assembly

out of the bay.

c. Remove the screws to

separate the HDD and cover.

2.Disassembly

9. Hard Disk



•4 Screws

Removing the Hard Disk Drive 2 - 9

Page 36

Disassembly

Removing the System Memory (RAM)

Figure 4

Memory Socket

Cover Removal

a. Remove the screws. b. Carefully lift the cover off

the computer.

2.Disassembly

The computer has two memory sockets for 200 pin (SO-DIMM) Small Outline Dual In-line Memory Modules supporting DDR 266MHz (see “Memory” on page 1 - 3). The main memory can be expanded up to 2GB. The SO-DIMM modules supported are 128MB, 256MB, 512MB and 1024MB. The total memory size is automatically detected by the POST routine once you turn on your computer.

Memory Upgrade Process

1. Turn off the computer, turn it over and remove the battery (page 2 - 7).

2. Remove screws - (Figure 4a) from the memory socket cover

3. Carefully lift up the memory socket cover off the computer (Figure 4b).

4. If there is a module currently installed which needs to be upgraded/replaced then remove it.

1 6



5. Socket Cover

•4 Screws

2 - 10 Removing the System Memory (RAM)

Page 37

Disassembly

5. Gently pull the two release latches ( & in Figure 5a) on the sides of the memory socket toward the sides of

1 2

the computer.

b.a.

6. The module (Figure 5b) will pop-up, and you can remove it.

7. Pull the latches to release the second module if necessary.

8. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.

9. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go. DO NOT FORCE IT; it should fit without much pressure.

10. Press the module in and down towards the mainboard until the slot levers click into place to secure the module.

11. Replace the memory socket cover and the 6 screws (see Figure 4).

12. Restart the computer.

13. The BIOS will register the new memory configuration as it starts up.

Figure 5

Removing/

Installing a RAM

Module

a. Pull the release

latches.

b. Remove the mod-

ule.

2.Disassembly



Contact Warning

Be careful not to touch the metal pins on the module’s connecting edge. Even the cleanest hands have oils which can attract particles, and degrade the module’s performance.



3. RAM Module

Removing the System Memory (RAM) 2 - 11

Page 38

Disassembly

Removing the Optical Device

Figure 6

Optical Device

Removal

a. Remove the screws. b. Carefully lift the cover off

the computer.

c. Push the optical device

out off the computer at point 2.

d. Remove the optical de-

vice.

2.Disassembly

1. Turn off the computer, turn it over and remove the battery (page 2 - 7).

2. Remove screw (Figure 6a) and carefully lift up the optical device removal cover (Figure 6b).

3. Use a screwdriver to carefully push the optical device assembly out of the computer at point (Figure 6c).

1 2

3 4

4. Insert the new device and carefully slide it into the computer (the device only fits one way. DO NOT FORCE IT; The screw holes should line up.

5. Replace the optical device removal cover and the screw.

6. Restart the computer to allow it to automatically detect the new device.



2. Optical Device Removal Cover

3. Optical Device

•1 Screw

2 - 12 Removing the Optical Device

Page 39

Removing the Processor

1. Turn off the computer, remove the battery (page 2 - 7) and turn it over.

2. Remove screws - from the CPU cover

3. Carefully lift up the CPU cover off the computer.

4. Remove screws

5. Carefully lift up the heat sink (Figure 7c) off the computer.

6. Remove screws

7. Carefully lift up the fan cover (Figure 7d) off the computer.

1 2

- (Figure 7c) from the heat sink in the order indicated on the label.

4 6

- (Figure 7d) from the fan cover.

8 10

Disassembly

Figure 7

Processor Removal

a. Remove the screws. b. Carefully lift the cover off

and remove the screws in the order indicated.

c. Remove the heat sink

and remove the screws.

d. Carefully lift the fan cov-

er off the computer.

2.Disassembly



3. CPU Cover

7. Heat Sink

11. Fan shield cover

•8 Screws

Removing the Processor 2 - 13

Page 40

Disassembly

Figure 8

Processor Removal

(cont’d)

a. Turn the release latch to

unlock the CPU.

b. Lift the CPU out of the

socket.

2.Disassembly

8. Turn the release latch towards the unlock symbol , to release the CPU (Figure 8a).

9. Carefully (it may be hot) lift the CPU up out of the socket (Figure 8b).

10. When re-inserting the CPU, pay careful attention to the pin alignment; it will fit only one way (don’t force it!).

LockedUnlocked



2. CPU

2 - 14 Removing the Processor



Caution

The heat sink, and CPU area in general, contains parts which are subject to high temperatures. Allow the area time to cool before removing these parts.

Page 41

Removing the Keyboard

1. Turn off the computer, remove the battery (page 2 - 7).

2. Press the three keyboard latches at the top of the keyboard to elevate the keyboard from its normal position (you may need to use a small screwdriver to do this).

3. Carefully lift the keyboard up and out, being careful not to bend the keyboard ribbon cable (Figure 9b).

4. Disconnect the keyboard ribbon cable from the locking collar socket (Figure 9b) and lift the keyboard up out

2 3

of the computer.

5. Remove screw and disconnect the cables

- .

5 6

Disassembly

Figure 9

Keyboard Removal

a. Press the latches to ele-

vate the keyboard.

b. Disconnect the keyboard

cable from the locking

collar. c. Remove the keyboard. d. Remove screw and dis-

connect the cables.

2.Disassembly



3. Keyboard

•1 Screw

Removing the Keyboard 2 - 15

Page 42

Disassembly

Figure 10

Wireless LAN

Removal

a. Pull the release latches,

and disconnect the cable

b. Remove the module.

2.Disassembly

Removing the Wireless LAN

1. Turn off the computer, turn it over and remove the battery (page 2 - 7), and RAM cover (page 2 - 10).

2. Gently pull the two release latches ( & in Figure 10a) on the sides of the wireless LAN toward the sides of the computer, and carefully disconnect the antenna cable .

3. The module (Figure 10b) will pop-up, and you can remove it (Figure 10c).

a. b.

1 2



4. Wireless LAN Module

2 - 16 Removing the Wireless LAN

Page 43

Removing the Bottom Case

Disassembly

1. Turn off the computer, remove the battery (page 2 - 7), hard disk (page 2 - 8), RAM (page 2 - 10), Optical Device (page 2 - 12), and CPU (page 2 - 13).

2. Remove screws

3. Remove screws

4. Carefully lift the bottom case

- (Figure 11a) from the bottom of the computer and disconnect cable .

1 13 14

- (Figure 11b).

15 16

17 18

off the LCD and top case assembly (Figure 11c).

Figure 11

LCD & Bottom Case

Removal

a. Remove the screws from

the bottom of the computer and disconnect the cable.

b. Remove the screws from

the side of the computer.

c. Lift the bottom case off

the LCD and top case assembly.

2.Disassembly



17. LCD & top case

18. Bottom case

•15 Screws

Removing the Bottom Case 2 - 17

Page 44

Disassembly

Figure 12

Modem Removal

a. Remove the screws. b. Carefully disconnect the

cables and connector, and remove the modem.

2.Disassembly

Removing the Modem

1. Turn off the computer, turn it over and remove the battery (page 2 - 7), hard disk (page 2 - 8), RAM (page 2 - 10), Optical Device (page 2 - 12), CPU (page 2 - 13) and bottom case (page 2 - 17).

2. Remove screws - (Figure 12a).

3. Carefully disconnect cables -

a. b.

1 2

3 4 5

and connector , and lift the modem (Figure 12b) off the computer.



6. Modem

•2 Screws

2 - 18 Removing the Modem

Page 45

Removing the Audioboard

Disassembly

1. Turn off the computer, remove the battery (page 2 - 7), hard disk (page 2 - 8), RAM (page 2 - 10), Optical Device (page 2 - 12), CPU (page 2 - 13), and bottom case (page 2 - 17).

2. Remove screws

3. Lift the audioboard off the mainboard assembly (Figure 15b).

1 2 3 4

- and disconnect cables & .

Figure 13

Audioboard

Removal

a. Remove screws and dis-

connect the cables.

d. Lift the audioboard off

the mainboard.

2.Disassembly



5. Audioboard

6. Audio Cable

•2 Screws

Removing the Audioboard 2 - 19

Page 46

Disassembly

Removing the Multi-function board

Figure 14

Multi-function board

Removal

a. Remove screws and dis-

connect the cables.

d. Lift the multi-function-

board and bracket off the mainboard assembly.

2.Disassembly

1. Turn off the computer, remove the battery (page 2 - 7), hard disk (page 2 - 8), RAM (page 2 - 10), Optical Device (page 2 - 12), CPU (page 2 - 13), and bottom case (page 2 - 17).

2. Remove screws

3. Lift the multi-function board and bracket off the mainboard assembly (Figure 15b).

a. b.

3 4

1 2 3 8

& and disconnect cables - (Figure 15a).

9 10



9. Multi-function board

10. Bracket

•2 Screws

2 - 20 Removing the Multi-function board

Page 47

Removing the Mainboard

Disassembly

1. Turn off the computer, remove the battery (page 2 - 7), hard disk (page 2 - 8), RAM (page 2 - 10), Optical Device (page 2 - 12), modem (page 2 - 18), CPU (page 2 - 13), keyboard (page 2 - 15), bottom case (page 2 - 17), and audioboard (page 2 - 19).

2. Remove screws

3. Disconnect cables - and remove screws - (Figure 15c).

4. Separate the mainboard , and top case , then disconnect the TouchPad cable (Figure 15d).

1 3

- and lift the DC/DC board from the mainboard .

9 10 11

5 12

4 5

a. b.

c. d.

Figure 15

Mainboard Removal

a. Remove screws. b. Lift the DC/DC board off

the mainboard.

c. Disconnect the cables

and remove the screws.

d. Separate the mainboard,

and top case. Disconnect the TouchPad cable.

2.Disassembly

4. DC/DC board

5. Mainboard

12. Top case

•5 Screws



Removing the Mainboard 2 - 21

Page 48

Disassembly

Removing the TouchPad and Click Board

Figure 16

TouchPad and Click

Board Removal

a. Remove the screws. b. Separate the click board

from the top case. c. Remove the screws. d. Separate the touchpad

from the top case.

2.Disassembly

2. Remove screws - (Figure 16a) and disconnect cables

1 4 5 6

& from the click board assembly , and lift

the click board off the top case (Figure 16b).

3. Remove screws

4. Lift the TouchPad

- (Figure 16c).

off the top case and separate the TouchPad from its casing (Figure 16d).



7. Click Board

11. TouchPad

12. Casing

•7 Screws

2 - 22 Removing the TouchPad and Click Board

Page 49

Removing the Inverter

Disassembly

1. Turn off the computer, remove the battery (page 2 - 7).

2. Remove the rubber covers and screws - from the LCD (Figure 17a).

3. Run your finger around the middle of the frame to carefully unsnap the LCD front panel module from the back.

4. Remove screw

5. Lift the inverter off the LCD assembly (Figure 17d).

6 7 8

from the inverter over and disconnect the cables & from the rear of the inverter .

1 4

Figure 17

Inverter Removal

a. Remove the rubber cov-

ers and screws.

b. Unsnap the frame from

the LCD front panel module.

c. Remove screw from in-

verter and disconnect the cables.

c. Lift the inverter off the

LCD assembly.

2.Disassembly



5. LCD Front Panel

9. Inverter

• 4 Rubber covers

•5 Screws

Removing the Inverter 2 - 23

Page 50

Disassembly

Removing the Speakers

Figure 18

Speakers Removal

a. Remove the screws. b. Separate the speakers

from the LCD front panel assembly.

2.Disassembly

1. Turn off the computer, remove the battery (page 2 - 7), hard disk (page 2 - 8), Optical Device (page 2 - 12), CPU (page 2 - 13), bottom case (page 2 - 17), mainboard (page 2 - 21), and inverter (page 2 - 23).

2. Remove the screws - (Figure 18a) from the speakers.

3. Separate the speakers (Figure 18b) from the LCD front panel assembly.

1 4



5. Speakers

•4 Screws

2 - 24 Removing the Speakers

Page 51

Removing the LCD Panel

Disassembly

2. Remove screws - from the side of the LCD panel (Figure 19a).

3. Gently lift the LCD panel off the LCD assembly (Figure 19b).

a. b.

1 4

Removing the PC Camera Module

1. Turn off the computer, remove the battery (page 2 - 7), and inverter (page 2 - 23).

2. Disconnect cable from the PC camera module (Figure 20a).

3. Lift the PC camera module (Figure 20b) off the LCD assembly.

Figure 19

LCD Panel Removal

a. Remove screws from the

side of the LCD panel.

b. Lift the LCD panel off the

LCD assembly.



7. LCD Panel

•4 Screws

Figure 20

PC Camera Removal

a. Disconnect the cable. b. Lift the PC Camera off

the LCD assembly.

2.Disassembly



2. PC Camera

Removing the LCD Panel 2 - 25

Page 52

Disassembly

2.Disassembly

2-26

Page 53

Appendix A:Part Lists

This appendix breaks down the M350H/ M360H/ M362H/ M363H series notebook’s construction into a series of illustrations. The component part numbers are indicated in the tables opposite the drawings.

Note: This section indicates the manufacturer’s part numbers. Your organization may use a different system, so be sure to cross-check any relevant documentation.

Note: Some assemblies may have parts in common (especially screws). However, the part lists DO NOT indicate the total number of duplicated parts used.

Part Lists

Note: Be sure to check any update notices. The parts shown in these illustrations are appropriate for the system at the time of publication. Over the product life, some parts may be improved or re-configured, resulting in new part numbers.

A.Part Lists

A-1

Page 54

Part Lists

Table 1 - 1

Part List Illustration

Location

Part List Illustration Location

The following table indicates where to find the appropriate part list illustration.

Part M350H M360H M362H M363H

Top

page A - 3 page A - 14 page A - 25 page A - 36

A.Part Lists

Bottom

LCD

CD-ROM Drive - QSI

CD-ROM Drive - SAMSUNG

CD-RW Drive - KME

CD-RW Drive - TEAC

Combo Drive - QSI

Combo Drive - TEAC-SAMSUNG

DVD-ROM Drive - QSI

DVD-ROM Drive - TOSHIBA

DVD-Dual Drive

page A - 4 page A - 15 page A - 26 page A - 37

page A - 5 page A - 16 page A - 27 page A - 38

page A - 6 page A - 17 page A - 28 page A - 39

page A - 7 page A - 18 page A - 29 page A - 40

page A - 8 page A - 19 page A - 30 page A - 41

page A - 9 page A - 20 page A - 31 page A - 42

page A - 10 page A - 21 page A - 32 page A - 43

page A - 11 page A - 22 page A - 33 page A - 44

page A - 12 page A - 23 page A - 34 page A - 45

page A - 13 ---

- page A - 24 page A - 35 page A - 46

A - 2 Part List Illustration Location

Page 55

Top (M350H)

Part Lists

Figure 1

Top (M350H)

A.Part Lists

Top (M350H) A - 3

Page 56

Part Lists

Bottom (M350H)

A.Part Lists

Bottom (M350H)

Figure 2

A - 4 Bottom (M350H)

Page 57

LCD (M350H)

Part Lists

Figure 3

LCD (M350H)

A.Part Lists

LCD (M350H) A - 5

Page 58

Part Lists

CD-ROM Drive -

QSI (M350H)

A.Part Lists

CD-ROM Drive - QSI (M350H)

Figure 4

A - 6 CD-ROM Drive - QSI (M350H)

Page 59

CD-ROM Drive - SAMSUNG (M350H)

Part Lists

Figure 5

CD-ROM Drive -

SAMSUNG

(M350H)

A.Part Lists

CD-ROM Drive - SAMSUNG (M350H) A - 7

Page 60

Part Lists

CD-RW Drive -

KME (M350H)

A.Part Lists

CD-RW Drive - KME (M350H)

Figure 6

A - 8 CD-RW Drive - KME (M350H)

Page 61

CD-RW Drive - TEAC (M350H)

Part Lists

Figure 7

CD-RW Drive TEAC (M350H)

A.Part Lists

CD-RW Drive - TEAC (M350H) A - 9

Page 62

Part Lists

Combo Drive - QSI

A.Part Lists

Combo Drive - QSI (M350H)

Figure 8

(M350H)

A - 10 Combo Drive - QSI (M350H)

Page 63

Combo Drive - TEAC-SAMSUNG (M350H)

Part Lists

Figure 9

Combo Drive -

TEAC-SAMSUNG

(M350H)

A.Part Lists

Combo Drive - TEAC-SAMSUNG (M350H) A - 11

Page 64

Part Lists

Figure 10

DVD-ROM Drive -

QSI (M350H)

A.Part Lists

DVD-ROM Drive - QSI (M350H)

A - 12 DVD-ROM Drive - QSI (M350H)

Page 65

DVD-ROM Drive - TOSHIBA (M350H)

Part Lists

Figure 11

DVD-ROM Drive -

TOSHIBA (M350H)

A.Part Lists

DVD-ROM Drive - TOSHIBA (M350H) A - 13

Page 66

Part Lists

Top (M360H)

A.Part Lists

Top (M360H)

Figure 12

A - 14 Top (M360H)

Page 67

Bottom (M360H)

Part Lists

Figure 13

Bottom (M360H)

A.Part Lists

Bottom (M360H) A - 15

Page 68

Part Lists

LCD (M360H)

A.Part Lists

LCD (M360H)

Figure 14

A - 16 LCD (M360H)

Page 69

CD-ROM Drive - QSI (M360H)

Part Lists

Figure 15

CD-ROM Drive -

QSI (M360H)

A.Part Lists

CD-ROM Drive - QSI (M360H) A - 17

Page 70

Part Lists

Figure 16

CD-ROM Drive -

SAMSUNG

A.Part Lists

CD-ROM Drive - SAMSUNG (M360H)

(M360H)

A - 18 CD-ROM Drive - SAMSUNG (M360H)

Page 71

CD-RW Drive - KME (M360H)

Part Lists

Figure 17

CD-RW Drive -

KME (M360H)

A.Part Lists

CD-RW Drive - KME (M360H) A - 19

Page 72

Part Lists

Figure 18

CD-RW Drive -

TEAC (M360H)

A.Part Lists

CD-RW Drive - TEAC (M360H)

A - 20 CD-RW Drive - TEAC (M360H)

Page 73

Combo Drive - QSI (M360H)

Part Lists

Figure 19

Combo Drive - QSI

(M360H)

A.Part Lists

Combo Drive - QSI (M360H) A - 21

Page 74

Part Lists

Figure 20

Combo Drive -

TEAC-SAMSUNG

A.Part Lists

Combo Drive - TEAC-SAMSUNG (M360H)

(M360H)

A - 22 Combo Drive - TEAC-SAMSUNG (M360H)

Page 75

DVD-ROM Drive - QSI (M360H)

Part Lists

Figure 21

DVD-ROM Drive -

QSI (M360H)

A.Part Lists

DVD-ROM Drive - QSI (M360H) A - 23

Page 76

Part Lists

Figure 22

DVD-Dual Drive

A.Part Lists

DVD-Dual Drive (M360H)

(M360H)

A - 24 DVD-Dual Drive (M360H)

Page 77

Top (M362H)

Part Lists

Figure 23

Top (M362H)

A.Part Lists

Top (M362H) A - 25

Page 78

Part Lists

Bottom (M362H)

A.Part Lists

Bottom (M362H)

Figure 24

A - 26 Bottom (M362H)

Page 79

LCD (M362H)

Part Lists

Figure 25

LCD (M362H)

A.Part Lists

LCD (M362H) A - 27

Page 80

Part Lists

CD-ROM Drive -

QSI (M362H)

A.Part Lists

CD-ROM Drive - QSI (M362H)

Figure 26

A - 28 CD-ROM Drive - QSI (M362H)

Page 81

CD-ROM Drive - SAMSUNG (M362H)

Part Lists

Figure 27

CD-ROM Drive -

SAMSUNG

(M362H)

A.Part Lists

CD-ROM Drive - SAMSUNG (M362H) A - 29

Page 82

Part Lists

Figure 28

CD-RW Drive -

KME (M362H)

A.Part Lists

CD-RW Drive - KME (M362H)

A - 30 CD-RW Drive - KME (M362H)

Page 83

CD-RW Drive - TEAC (M362H)

Part Lists

Figure 29

CD-RW Drive TEAC (M362H)

A.Part Lists

CD-RW Drive - TEAC (M362H) A - 31

Page 84

Part Lists

Figure 30

Combo Drive - QSI

A.Part Lists

Combo Drive - QSI (M362H)

(M362H)

A - 32 Combo Drive - QSI (M362H)

Page 85

Combo Drive - TEAC-SAMSUNG (M362H)

Part Lists

Figure 31

Combo Drive -

TEAC-SAMSUNG

(M362H)

A.Part Lists

Combo Drive - TEAC-SAMSUNG (M362H) A - 33

Page 86

Part Lists

Figure 32

DVD-ROM Drive -

QSI (M362H)

A.Part Lists

DVD-ROM Drive - QSI (M362H)

A - 34 DVD-ROM Drive - QSI (M362H)

Page 87

DVD-Dual Drive (M362H)

Part Lists

Figure 33

DVD-Dual Drive

(M362H)

A.Part Lists

DVD-Dual Drive (M362H) A - 35

Page 88

Part Lists

Top (M363H)

A.Part Lists

Top (M363H)

Figure 34

A - 36 Top (M363H)

Page 89

Bottom (M363H)

Part Lists

Figure 35

Bottom (M363H)

A.Part Lists

Bottom (M363H) A - 37

Page 90

Part Lists

LCD (M363H)

A.Part Lists

LCD (M363H)

Figure 36

A - 38 LCD (M363H)

Page 91

CD-ROM Drive - QSI (M363H)

Part Lists

Figure 37

CD-ROM Drive -

QSI (M363H)

A.Part Lists

CD-ROM Drive - QSI (M363H) A - 39

Page 92

Part Lists

Figure 38

CD-ROM Drive -

SAMSUNG

A.Part Lists

CD-ROM Drive - SAMSUNG (M363H)

(M363H)

A - 40 CD-ROM Drive - SAMSUNG (M363H)

Page 93

CD-RW Drive - KME (M363H)

Part Lists

Figure 39

CD-RW Drive -

KME (M363H)

A.Part Lists

CD-RW Drive - KME (M363H) A - 41

Page 94

Part Lists

Figure 40

CD-RW Drive -

TEAC (M363H)

A.Part Lists

CD-RW Drive - TEAC (M363H)

A - 42 CD-RW Drive - TEAC (M363H)

Page 95

Combo Drive - QSI (M363H)

Part Lists

Figure 41

Combo Drive - QSI

(M363H)

A.Part Lists

Combo Drive - QSI (M363H) A - 43

Page 96

Part Lists

Figure 42

Combo Drive -

TEAC-SAMSUNG

A.Part Lists

Combo Drive - TEAC-SAMSUNG (M363H)

(M363H)

A - 44 Combo Drive - TEAC-SAMSUNG (M363H)

Page 97

DVD-ROM Drive - QSI (M363H)

Part Lists

Figure 43

DVD-ROM Drive -

QSI (M363H)

A.Part Lists

DVD-ROM Drive - QSI (M363H) A - 45

Page 98

Part Lists

Figure 44

DVD-Dual Drive

A.Part Lists

DVD-Dual Drive (M363H)

(M363H)

A - 46 DVD-Dual Drive (M363H)

Page 99

Appendix B:Schematic Diagrams

This appendix has circuit diagrams of the M350H/ M360H/ M362H/ M363H notebook’s PCB’s. The following table indicates where to find the appropriate schematic diagram.

Schematic Diagrams

Diagram - Page Diagram - Page

System Block Diagram - Page B - 2 ROM - Page B - 19

Socket 479 - 1 of 2 - Page B - 3 TI1394 (TSB43AB21) - Page B - 20

Socket 479 - 2 of 2 - Page B - 4 Hitachi H8S - Page B - 21

Montara GM-1 - Page B - 5 CON; Mini-PCI - Page B - 22

Montara GM-2 - Page B - 6 Audio Codec ALC202 - Page B - 23

Montara GM-3 - Page B - 7 PCMCIA (ENE1410) - Page B - 24

DDRAM - Page B - 8 PCMCIA Socket - Page B - 25

DDR Termination - Page B - 9 AC IN; Power Button - Page B - 26

Clock Generator - Page B - 10 CH7011; TV-Out - Page B - 27

LVDS; CRT - Page B - 11 V_CORE - Page B - 28

ICH4-1 (1 of 3) - Page B - 12 Charger - Page B - 29

ICH4-2 (2 of 3) - Page B - 13 Multi-Function Board - Page B - 30

ICH4-3 (3 of 3) - Page B - 14 Audio Jack Board - Page B - 31

USB 2.0, Wireless LAN - Page B - 15 5V, 3.3V, 12VS, +1.2V - Page B - 32

Table 1

Schematic

Diagrams

B.Schematic Diagrams

MDC, BT, CCT - Page B - 16 +2.5V, +1.25V, +1.5V - Page B - 33

HDD, CDROM - Page B - 17 Click Board - Page B - 34

LAN RTL8100B - Page B - 18

B-1

Page 100

Schematic Diagrams

System Block Diagram

Sheet 1 of 29

System Block

Diagram

B.Schematic Diagrams

POWER BOARD

CLICK BOARD

AUDIO BOARD

CLOCK GEN.

CCD

TOUCH PAD CONN

Wireless Lan

CPU CORE POEWR (VCORE)

CRT OUT

LVDS

LCD CONN(LVDS)

USB 1USB 2USB 3

SM BUS

TEMP SENSOR

USB2.0

CPU FAN

Banias Processor

479 uFCPGA PG3,4

Montara-GML GMCH 732 uFCBGA

HUB LINK

INTEL ICH4 421 BGA

KB CTRL. H8 2211

SYSTEM BIOS

BATTERY

SM BUS

AC'97 LINK

PCI BUS

Pri. IDE

Sec. IDE

FWM

CD-ROM/DVD/CD-RW

O'ning *3357

MEMORY TERMINATIONS

DDR SDRAM SOCKET

SO-DIMM0 SO-DIMM1

RJ-11

DDR VR

33MHz

ATA-100

(50 Pin)

H.D.D.

MDC & BT MODULE

MDC CONN.

MiniPCI SOCKET

Wireless Lan

Multi Function Board

ACIN;POWER BUTTON

Charger

MICINSPK

SPDIF OUT

AC'97 CODEC

(ALC202)

OUT

AUDIO AMP.

(APA2020A)

(PCI-1) (PCI-2)

LAN RTL8100B

RJ-45

CARD BUS ENE-1410

PCMCIA SOCKET*1

B - 2

KBC CONN

Clevo M350H, M360H, M362H, M363H Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Notice

Trademarks

About this Manual

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

Instructions for Care and Operation

Power Safety

Battery Precautions

Related Documents

1: Introduction

Overview

System Specifications

Design Differences

Gloss Style Top Cover Designs

External Locator - Top View

External Locator - Front & Left Side Views

External Locator - Right Side & Rear Views

External Locator - Bottom View

Mainboard Overview - Top (Key Parts)

Mainboard Overview - Bottom (Key Parts)

Mainboard Overview - Top (Connectors)

Mainboard Overview - Bottom (Connectors)

2: Disassembly

Overview

Maintenance Tools

Connections

Maintenance Precautions

Cleaning

Disassembly Steps

To remove the Battery:

1. Remove the battery page 2 - 7

To remove the HDD:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

To remove the System Memory:

1. Remove the battery page 2 - 7

2. Remove the system memory page 2 - 10

To remove the Optical Device:

1. Remove the battery page 2 - 7

2. Remove the optical device page 2 - 12

To remove the Processor:

1. Remove the battery page 2 - 7

2. Remove the processor page 2 - 13

To remove the Keyboard:

1. Remove the battery page 2 - 7

2. Remove the keyboard page 2 - 15

To remove the Wireless LAN:

1. Remove the battery page 2 - 7

2. Remove the processor page 2 - 13

3. Remove the wireless LAN page 2 - 16

To remove the Bottom Case:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the system memory page 2 - 10

4. Remove the optical device page 2 - 12

5. Remove the processor page 2 - 13

6. Remove the bottom case page 2 - 17

To remove the Modem:

1. Remove the battery page 2 - 7

2. Remove the bottom case page 2 - 17

3. Remove the modem page 2 - 18

To remove the Audioboard:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the optical device page 2 - 12

4. Remove the processor page 2 - 13

5. Remove the bottom case page 2 - 17

6. Remove the audioboard page 2 - 19

To remove the Multi-function board:

1. Remove the battery page 2 - 7

2. Remove the HDD page 2 - 8

3. Remove the optical device page 2 - 12

4. Remove the processor page 2 - 13

5. Remove the bottom case page 2 - 17

6. Remove the multi-function board page 2 - 20

To remove the Mainboard: