Clevo D400S, D410S Service Manual
Preface
I
Preface
Notebook Computer
D400S/D410S
Service Manual
Preface
II
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained
herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are
they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or
reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of
their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement
of that product or its manufacturer.
Version 1.0
March 2003
Trademarks
Intel® and Pentium® are registered trademarks of Intel Corporation.
Windows® is a registered trademark of Microsoft Corporation.
Other brand and product names are trademarks and./or registered trademarks of their respective companies.
Preface
III
Preface
About this Manual
This manual is intended for service personnel who have completed sufficient training to undertake the maintenance and
inspection of personal computers.
It is organized to allow you to look up basic information for servicing and/or upgrading components of the D400S/D410S
series notebook PC.
The following information is included:
Chapter 1, Introduction, provides general information about the location of system elements and their specifications.
Chapter 2, Disassembly, provides step-by-step instructions for disassembling parts and subsystems and how to upgrade
elements of the system.
Appendix A, Part Lists
Appendix B, Schematic Diagrams
Appendix C, Upgrading Flash ROM BIOS
Preface
IV
Preface
Related Documents
You may also need to consult the following manual for additional information:
User’s Manual on CD
This describes the notebook PC’s features and the procedures for operating the computer and its ROM-based setup program. It also describes the installation and operation of the utility programs provided with the notebook PC.
Preface
V
Preface
Contents
Introduction ..............................................1-1
Overview ......................................................................................... 1-1
System Specifications .....................................................................1-2
Processor .........................................................................................1-2
Core Logic .......................................................................................1-2
Structure ..........................................................................................1-2
Security ............................................................................................ 1-2
Memory ........................................................................................... 1-2
BIOS ................................................................................................ 1-2
LCD Options ...................................................................................1-2
Display ............................................................................................1-3
Storage Devices ...............................................................................1-3
Audio ............................................................................................... 1-3
Keyboard ......................................................................................... 1-4
Interface ........................................................................................... 1-4
PC Card ...........................................................................................1-4
Communication ............................................................................... 1-4
Power Management .........................................................................1-5
Power ............................................................................................... 1-5
Indicators .........................................................................................1-5
Environmental Spec ........................................................................1-5
Physical Dimensions .......................................................................1-5
Weight .............................................................................................1-5
Optional ........................................................................................... 1-6
Design Differences ..........................................................................1-6
External Locator - Top View ..........................................................1-7
External Locator - Front & Left Side Views ...................................1-8
External Locator - Right Side & Rear Views ..................................1-9
External Locator - Bottom View ...................................................1-10
Mainboard Overview - Top (Key Parts) .......................................1-11
Mainboard Overview - Bottom (Key Parts) ................................. 1-12
Mainboard Overview - Top (Connectors) .................................... 1-13
Mainboard Overview - Bottom (Connectors) ............................... 1-14
Disassembly ...............................................2-1
Overview ......................................................................................... 2-1
Maintenance Tools .......................................................................... 2-2
Connections .................................................................................... 2-2
Maintenance Precautions ................................................................ 2-3
Cleaning .......................................................................................... 2-3
Disassembly Steps .......................................................................... 2-4
Removing the Battery ..................................................................... 2-8
Removing the Hard Disk Drive ...................................................... 2-9
Hard Disk Upgrade Process ............................................................ 2-9
Removing the System Memory (RAM) ....................................... 2-10
Memory Upgrade Process ............................................................. 2-10
Removing the CD Device ............................................................. 2-12
Removing the Bluetooth Module .................................................. 2-14
Removing the Wireless LAN Module .......................................... 2-15
Removing the Processor ............................................................... 2-16
Removing the Keyboard ............................................................... 2-18
Removing the Keyboard Shielding Plate ...................................... 2-19
Removing the LCD and Top Case ................................................ 2-20
Removing the TouchPad and Click Board ................................... 2-22
Removing the Switch Board ......................................................... 2-23
Removing the Modem .................................................................. 2-24
Removing the Speakers ................................................................ 2-25
Removing the Mainboard ............................................................. 2-26
Removing the Fan Unit ................................................................. 2-27
Removing the Floppy Disk Drive Assembly ................................ 2-28
Removing the PC Card Assembly ................................................ 2-29
Preface
VI
Preface
Removing the LCD Front Panel Module ......................................2-30
Removing the Inverter ...................................................................2-31
Removing the PC Video Camera Module .....................................2-32
Removing the LCD Module ..........................................................2-33
Part Lists ..................................................A-1
Part List Illustration Location ........................................................A-2
Top (400S) ......................................................................................A-3
Bottom (400S) ................................................................................ A-4
LCD 14" (400S) .............................................................................A-5
LCD 15" (400S) .............................................................................A-6
CD-ROM Drive (400S) .................................................................. A-7
CD-RW Drive (400S) .....................................................................A-8
Combo Drive (400S) ......................................................................A-9
DVD-ROM Drive (400S) .............................................................A-10
Floppy Disk Drive (400S) ............................................................A-11
Hard Disk Drive (400S) ...............................................................A-12
Top (410S) ....................................................................................A-13
Bottom (410S) ..............................................................................A-14
LCD 14" (410S) ...........................................................................A-15
LCD 15" (410S) ...........................................................................A-16
CD-ROM Drive (410S) ................................................................A-17
CD-RW Drive (410S) ...................................................................A-18
Combo Drive (410S) ....................................................................A-19
DVD-ROM Drive (410S) .............................................................A-20
Floppy Disk Drive (410S) ............................................................A-21
Hard Disk Drive (410S) ...............................................................A-22
Schematic Diagrams.................................B-1
System Block Diagram ...................................................................B-2
Socket 478 1 of 2 ............................................................................ B-3
Socket 478 & ITP 2 of 2 .................................................................B-4
Clock Generator ............................................................................. B-5
M650 (Host/AGP) 1 of 4 ................................................................B-6
M650 (Memory for DDR) 2 of 4 ....................................................B-7
M650 (& CRT Out) 3 of 4 ..............................................................B-8
M650 (Power) 4 of 4 .......................................................................B-9
DDR Memory DIMM ...................................................................B-10
DDR SSTL-2 Termination ...........................................................B-11
LVDS Interface (SiS302LV) ........................................................B-12
Panel Con & LED Indicator .........................................................B-13
962 (PCI/IDE/HyperZip) 1 of 4 ....................................................B-14
962 (Misc Signals) 2 of 4 ..............................................................B-15
962 (USB I/F) 3 of 4 .....................................................................B-16
962 (Power & RTC) 4 of 4 ...........................................................B-17
HDD/Combo Connector ...............................................................B-18
USB Port .......................................................................................B-19
PCMCIA TI1410 ..........................................................................B-20
PCMCIA Power ............................................................................B-21
1394 PHY TSB41LV01 ................................................................B-22
LPC SI/O ......................................................................................B-23
LPT/COM Port .............................................................................B-24
LPC H8 .........................................................................................B-25
LAN RTL8100BL ........................................................................B-26
Audio Codec ALC201A ...............................................................B-27
Audio Out & Off Board Connectors .............................................B-28
System Power Control ..................................................................B-29
Fan Control and SpeedStep ..........................................................B-30
VCORE .........................................................................................B-31
DDR Power ...................................................................................B-32
System ...........................................................................................B-33
Charger .........................................................................................B-34
SW Board and HotKey .................................................................B-35
TouchPad and Switch Board ........................................................B-36
Updating the FLASH ROM BIOS......... C-1
Introduction
Overview 1 - 1
1.Introduction
1: Introduction
Overview
This manual covers the information you need to service or upgrade the D400S/D410S series notebook computer. Information about operating the computer (e.g. getting started, and the Setup utility) is in the User’s Manual. Information
about drivers (e.g. VGA & audio) is also found in User’s Manual. That manual is shipped with the computer.
Operating systems (e.g. DOS, Windows 9x, Windows NT 4.0, Windows 2000, Windows XP, OS/2 Warp, UNIX, etc.) have
their own manuals as do application software (e.g. word processing and database programs). If you have questions about
those programs, you should consult those manuals.
The D400S/D410S series notebook is designed to be upgradeable. See “Disassembly” on page 2 - 1 for a detailed de-
scription of the upgrade procedures for each specific component. Please note the warning and safety information indicated by the “!” symbol.
The balance of this chapter reviews the computer’s technical specifications and features.
Introduction
1 - 2 System Specifications
1.Introduction
System Specifications
Processor
• Intel Pentium 4 Processor - (478-pin) FC-PGA2 package
(
µ0.13) 0.13 Micron Process Technology, 512KB L2 Cache & 400MHz FSB - 2.0/ 2.2/ 2.4/ 2.5 /2.6 GHz
(µ0.13) 0.13 Micron Process Technology, 512KB L2 Cache & 533MHz FSB - 2.26/ 2.4/ 2.53/ 2.66/ 2.66/ 2.8 GHz
Core Logic
• SIS M650 + 962
Structure
• PC99 compliant
Security
• Security (Kensington® Type) Lock
• BIOS Password
Memory
• Two 200-pin DDR SODIMM sockets, supporting DDR SDRAM SODIMM (2.5V) - DDR 200/ DDR 266/ DDR 333 compliant
• Memory expandable up to 1024MB (128/256/512MB SODIMM Modules)
BIOS
• One 512KB Flash ROM
•Phoenix BIOS
LCD Options
• 14.1" XGA TFT (1024*768)
• 15.0" XGA TFT (1024*768)
• 15.0" SXGA+ TFT(1400*1050)
Introduction
System Specifications 1 - 3
1.Introduction
Display
• High Performance 256-bit 3D engine
• Advanced HW accelerator for DVD playback
• Fully Direct X 8.0 compliant graphics engine
• Dual-View display monitor
• CRT Resolution up to 2048 * 1536
Storage Devices
•3.5" 3-mode Floppy Disk Drive
• Easy changeable 2.5" 9.5 mm (h) Hard Disk Drive
Supporting Master mode IDE
Supports PIO mode 4
ATA-33/66/100/133
Ultra DMA
• 12.7mm(h) Device Bay for ONE of the following drive configuration options:
•24* CD-ROM
• 8* DVD-ROM
• CD-RW (16* CD-R/ 10* CD-RW/ 24* CD-ROM)
• Combo (8* DVD-ROM/ 8* CD-R/ 8* CD-RW/ 24* CD-ROM)
• Combo (8* DVD-ROM/ 24* CD-R/ 10* CD-RW/ 24* CD-ROM)
Audio
• AC'97 2.1 compliant interface
• 3D stereo enhanced sound system
• Compatible with Sound-Blaster PRO™
• S/PDIF Digital output (5.1 CH) for DVD content and stereo audio
• Microphone-in jack
• Headphone-out jack
• Built-in microphone
• 2 built-in speakers (1 watt 35 * 16 mm)
!
Video Memory
The system allocates
or "shares" a portion of
system memory for
video use. "Shared"
memory is user-configurable via the SCU.
The default setting is
set to 32MB.
Introduction
1 - 4 System Specifications
1.Introduction
Keyboard
• “Win Key” keyboard
Interface
• Built-in TouchPad (scrolling key functionality integrated)
• Three USB 2.0 ports
• One IEEE 1394 port
• One S-Video jack for TV output
• One serial port
• One parallel port (LPT1), supporting ECP / EPP
• Infrared transceiver IrDA 1.1 FIR/SIR/ASKIR
• One external CRT monitor port
• One external keyboard/mouse (through Y cable) PS/2 port
• One speaker-out/headphone-out jack
• One microphone-in jack
• One RJ-11 jack for modem
• One RJ-45 jack for 100M/10M LAN
• One S/PDIF out port
• One DC-in jack
PC Card
• One type II PCMCIA 3.3V/5V socket supporting CardBus
Communication
• Wireless Infrared transfer IrDA 1.1 compliant, 1cm - 1M operating distance, 115.2K bps SIR/ 4Mbps FIR
• 10/100Mb Ethernet LAN built-in
• 56K MDC modem V.90 & V.92 compliant
• 802.11b wireless LAN module (available as a factory option)
• Bluetooth module (available as a factory option)
• Built-in PC camera module (available as a factory option)
Introduction
System Specifications 1 - 5
1.Introduction
Power Management
• Supports ACPI v1.0b
• Supports Hibernate mode
• Supports Standby mode
• Supports battery low sleep
• Supports resume from modem ring
Power
• Full range AC adapter
• AC-Input 100~240V, 50~60H z
• DC Output 20V, 3.25A (90w)
• Supports one removable Smart Li-Ion battery 2200mAH/8 cell
Indicators
• LED indicators (HDD, Power On/ AC-In/ Suspend, Battery Charging/Battery Full, Num Lock, Caps Lock, Scroll Lock)
Environmental Spec
• Temperature
Operating: 5
°C ~ 35°C
Non-Operating: -20
°C ~ 60°C
• Relative Humidity
Operating: 20% ~ 80%
Non-Operating: 10% ~ 90%
Physical Dimensions
• 329 (w) x 275 (d) x 36.5 (h) mm
Weight
• 3.0 kg w/o battery
Introduction
1 - 6 System Specifications
1.Introduction
Optional
• DVD-ROM Drive
• CD-RW Drive
• Combination Drive
• Software DVD player
• Wireless LAN module
• Bluetooth module
•Video Camera
Design Differences
This manual refers to the two notebook designs pictured below. The designs vary slightly in external design. Photographs
used throughout this manual are of Design I.
Figure 1
Design Differences
Design I
Design II
Introduction
External Locator - Top View 1 - 7
1.Introduction
External Locator - Top View
Figure 2
Top View
1. Optional Built-in
USB Camera
2. LCD
3. Built-In
Microphone
4. LED Power &
Communication
Indicators
5. LED Status
Indicators
6. Hot-Key buttons
7. Close Cover
Switch
8. Power Button
9. Keyboard
10.TouchPad and
Buttons
2
6
4
5
7
1
8
3
9
10
Introduction
1 - 8 External Locator - Front & Left Side Views
1.Introduction
External Locator - Front & Left Side Views
Figure 3
Front View
1. LCD Latches
2. IEEE 1394 Port
3. S/PDIF Out Port
4. Microphone-In
Jack
5. Headphone-Out
Jack
6. Infrared
Transceiver
7. Wireless LAN On/
Off Switch
8. Built-In Speakers
4 5
6 7
1
2
1
3
8 8
Figure 4
Left Side View
1. CD Device Bay
2. USB 2.0 Port
3. Floppy Disk Drive
4. PC Card Slot
5. PC Card Slot Eject
Buttons
3
4
1
5
2
Introduction
External Locator - Right Side & Rear Views 1 - 9
1.Introduction
External Locator - Right Side & Rear Views
1
Figure 5
Right Side View
1. Security Lock Slot
Figure 6
Rear View
1. Vent
2. DC-In Jack
3. 2 * USB Ports
4. External Monitor
(CRT) Port
5. Parallel Port
6. Serial Port
7. S-Video-Out Port
8. PS/2 Type Port
9. RJ-11 Phone Jack
10.RJ-45 LAN Jack
3
4 5 6 7 8 9
10
1
2
Introduction
1 - 10 External Locator - Bottom View
1.Introduction
External Locator - Bottom View
Figure 7
Bottom View
1. Vent/Fan Outlets
2. Battery Cover
3. Hard Disk Cover
4. Bluetooth
Module Cover
5. CPU Heatsink
Cover
Note: The RAM and
optional Wireless
LAN module are located under the CPU
Heatsink Cover
1
1
2
4
5
3
Introduction
Mainboard Overview - Top (Key Parts) 1 - 11
1.Introduction
Mainboard Overview - Top (Key Parts)
Figure 8
Mainboard Top
Key Parts
1. PC Card
Assembly
2. Northbridge - SiS
M650
3. Southbridge - SiS
962
4. LPC Super I/O
NS PC87393
5. Flash ROM BIOS
1
2
3
4
5
Introduction
1 - 12 Mainboard Overview - Bottom (Key Parts)
1.Introduction
Mainboard Overview - Bottom (Key Parts)
Figure 9
Mainboard Bottom
Key Parts
1. CPU Socket (no
CPU installed)
2. Memory Sockets
(no memory
installed)
3. SiS 302LV TVOut Controller
4. LAN Controller
RTL8100BL
5. CardBus ENE
1410
6. ALC202 - Audio
Codec
7. 1394 PHY
TSB41LV01
8. Clock Generator
9. Keyboard
Controller - KBC
H8 H8S-2149 HM
1
2
3
4
5
6
7
8
9
Introduction
Mainboard Overview - Top (Connectors) 1 - 13
1.Introduction
Mainboard Overview - Top (Connectors)
Figure 10
Mainboard Top
Connectors
1. Modem Cable
Connector (CN1)
2. LCD and Inverter
Connector
(JLCD1)
3. Video Camera
Module
Connector
(JCCD1)
4. Switch Board
Connector
(JSW1)
5. Fan Connector
(JFAN1)
6. TouchPad
Connector (JTP1)
7. Keyboard
Connector (JKB1)
8. Modem
Connector
(JMDC1)
9. Speaker
Connector
(JSPK1)
10.Floppy Disk
Controller
(JFDD1)
11.Speaker
Connector
(JSPK2)
5
7
8
4
6
1
2
3
9
10
11
Introduction
1 - 14 Mainboard Overview - Bottom (Connectors)
1.Introduction
Mainboard Overview - Bottom (Connectors)
Figure 11
Mainboard Bottom
Connectors
1. Wireless LAN
Connector
(JWL1)
2. Fan Connector
(JFAN2)
3. CD Connector
(JCDROM1)
4. Hard Disk
Connector
(JHDD1)
5. Bluetooth
Connector (JBT1)
6. Battery
Connector
(JBAT1)
7. Battery
Connector (CN5)
1
2
3
4
5
6
7
Disassembly
Overview 2 - 1
2.Disassembly
2: Disassembly
Overview
This chapter provides step-by-step instructions for disassembling the D400S/D410S series notebook’s parts and sub-
systems. When it comes to reassembly, reverse the procedures (unless otherwise indicated).
We suggest you completely review any procedure before you take the computer apart.
Procedures such as upgrading/replacing the RAM, CD device and hard disk are included in the User’s Manual but are
repeated here for your convenience.
To make the disassembly process easier each section may have a box in the page margin. Information contained under
the figure # will give a synopsis of the sequence of procedures involved in the disassembly procedure. A box with a !
lists the relevant parts you will have after the disassembly process is complete. Note: The parts listed will be for the disassembly procedure listed ONLY, and not any previous disassembly step(s) required. Refer to the part list for the previous disassembly procedure. The amount of screws you should be left with will be listed here also.
A box with a " will provide any possible helpful information. A box with a ! contains warnings.
An example of these types of boxes are shown in the sidebar.
!
Component Parts
"
Information
!
Warning
Disassembly
2 - 2 Overview
2.Disassembly
NOTE: All disassembly procedures assume that the system is turned OFF, and disconnected from any power supply (the
battery is removed too).
Maintenance Tools
The following tools are recommended when working on the notebook PC:
• M3 Philips-head screwdriver
• M2.5 Philips-head screwdriver (magnetized)
• M2 Philips-head screwdriver
• Small flat-head screwdriver
• Pair of needle-nose pliers
• Anti-static wrist-strap
Connections
Connections within the computer are one of four types:
Locking collar sockets for ribbon connectors To release these connectors, use a small flat-head screwdriver to
gently pry the locking collar away from its base. When replacing the connection, make sure the connector is oriented in the
same way. The pin1 side is usually not indicated.
Pressure sockets for multi-wire connectors To release this connector type, grasp it at its head and gently
rock it from side to side as you pull it out. Do not pull on the
wires themselves. When replacing the connection, do not try to
force it. The socket only fits one way.
Pressure sockets for ribbon connectors To release these connectors, use a small pair of needle-nose pli-
ers to gently lift the connector away from its socket. When replacing the connection, make sure the connector is oriented in
the same way. The pin1 side is usually not indicated.
Board-to-board or multi-pin sockets To separate the boards, gently rock them from side to side as
you pull them apart. If the connection is very tight, use a small
flat-head screwdriver - use just enough force to start.
Disassembly
Overview 2 - 3
2.Disassembly
Maintenance Precautions
The following precautions are a reminder. To avoid personal injury or damage to the computer while performing a removal and/or replacement job, take the following precautions:
1. Don't drop it. Perform your repairs and/or upgrades on a stable surface. If the computer falls, the case and other
components could be damaged.
2. Don't overheat it. Note the proximity of any heating elements. Keep the computer out of direct sunlight.
3. Avoid interference. Note the proximity of any high capacity transformers, electric motors, and other strong mag-
netic fields. These can hinder proper performance and damage components and/or data. Y ou should also monitor
the position of magnetized tools (i.e. screwdrivers).
4. Keep it dry. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly
damaged.
5. Be careful with power. Avoid accidental shocks, discharges or explosions.
•Before removing or servicing any part from the computer, turn the computer off and detach any power supplies.
•When you want to unplug the power cord or any cable/wire, be sure to disconnect it by the plug head. Do not pull on the wire.
6. Peripherals – Turn off and detach any peripherals.
7. Beware of static discharge. ICs, such as the CPU and main support chips, are vulnerable to static electricity.
Before handling any part in the computer, discharge any static electricity inside the computer. When handling a
printed circuit board, do not use gloves or other materials which allow static electricity buildup. We suggest that
you use an anti-static wrist strap instead.
8. Beware of corrosion. As you perform your job, avoid touching any connector leads. Even the cleanest hands produce oils which can attract corrosive elements.
9. Keep your work environment clean. Tobacco smoke, dust or other air-born particulate matter is often attracted
to charged surfaces, reducing performance.
10. Keep track of the components. When removing or replacing any part, be careful not to leave small part s, such as
screws, loose inside the computer.
Cleaning
Do not apply cleaner directly to the computer, use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
!
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
Disassembly
2 - 4 Disassembly Steps
2.Disassembly
Disassembly Steps
The following table lists the disassembly steps, and on which page to find the related information. PLEASE PERFORM
THE DISASSEMBLY STEPS IN THE ORDER INDICATED.
To remove the Battery:
1. Remove the battery page 2 - 8
To remove the HDD:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
To remove the System Memory:
1. Remove the battery page 2 - 8
2. Remove the system memory page 2 - 10
To remove the CD Device:
1. Remove the battery page 2 - 8
2. Remove the CD Device page 2 - 12
To remove the Bluetooth Module:
1. Remove the battery page 2 - 8
2. Remove the Bluetooth module page 2 - 14
To remove the Wireless LAN Module:
1. Remove the battery page 2 - 8
2. Remove the Wireless LAN module page 2 - 15
To remove the Processor:
1. Remove the battery page 2 - 8
2. Remove the processor page 2 - 16
To remove the Keyboard:
1. Remove the battery page 2 - 8
2. Remove the keyboard page 2 - 18
To remove the Keyboard Shielding Plate:
1. Remove the battery page 2 - 8
2. Remove the keyboard page 2 - 18
3. Remove the keyboard shielding plate page 2 - 19
To remove the LCD and Top Case:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
Disassembly
Disassembly Steps 2 - 5
2.Disassembly
To remove the TouchPad and Click Board:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the touchpad and click board page 2 - 22
To remove the Switch Board:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the switch board page 2 - 23
To remove the Modem:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the modem page 2 - 24
To remove the Speakers:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the speakers page 2 - 25
Disassembly
2 - 6 Disassembly Steps
2.Disassembly
To remove the Mainboard:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the speakers page 2 - 25
12. Remove the mainboard page 2 - 26
To remove the Fan Unit:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the speakers page 2 - 25
12. Remove the mainboard page 2 - 26
13. Remove the fan unit page 2 - 27
To remove the Floppy Disk Drive Assembly:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the speakers page 2 - 25
12. Remove the mainboard page 2 - 26
13. Remove the floppy disk drive page 2 - 28
To remove the PC Card Assembly:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the speakers page 2 - 25
12. Remove the mainboard page 2 - 26
13. Remove the PC Card assembly page 2 - 29
Disassembly
Disassembly Steps 2 - 7
2.Disassembly
To remove the LCD Front Panel Module:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the front panel module page 2 - 30
To remove the Inverter:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the front panel module page 2 - 30
12. Remove the inverter page 2 - 31
To remove the PC Video Camera Module:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the front panel module page 2 - 30
12. Remove the PC Video Camera page 2 - 32
To remove the LCD Module:
1. Remove the battery page 2 - 8
2. Remove the HDD page 2 - 9
3. Remove the system memory page 2 - 10
4. Remove the CD Device page 2 - 12
5. Remove the Bluetooth module page 2 - 14
6. Remove the Wireless LAN module page 2 - 15
7. Remove the processor page 2 - 16
8. Remove the keyboard page 2 - 18
9. Remove the keyboard shielding plate page 2 - 19
10. Remove the LCD & top case page 2 - 20
11. Remove the front panel module page 2 - 30
12. Remove the inverter page 2 - 31
13. Remove the LCD module page 2 - 33
Disassembly
2 - 8 Removing the Battery
2.Disassembly
Removing the Battery
1. Turn the computer off, and turn it over.
2. Remove screws
& (Figure 1a) from the battery cover , and remove the cover.
3. Carefully (use a small screwdriver) disconnect the battery cable at point
(Figure 1b).
4. Lift the battery out of the computer.
5. When replacing the battery, connect the cable first.
!
3. Battery Cover
5. Battery
•2 Screws
1 2 3
4
5
1 2
4
a.
5
3
b.
Figure 1
Battery Removal
a. Remove the 2 screws
and the battery cover.
b. Carefully disconnect the
battery cable and remove
the battery.
Disassembly
Removing the Hard Disk Drive 2 - 9
2.Disassembly
Removing the Hard Disk Drive
The hard disk drive is mounted in a removable case and can be taken out to accommodate other 2.5" IDE hard disk drives
with a height of 9.5mm (h). Follow your operating system’s installation instructions, and install all necessary drivers and
utilities (as outlined in Chapter 4 of the User’s Manual) when setting up a new hard disk.
Hard Disk Upgrade Process
1. Turn off the computer, remove the battery (page 2 - 8) and turn it over.
2. Remove screws
& (Figure 2a) from the hard disk cover , and remove the cover.
3. Carefully (use a small screwdriver) disconnect the battery cable at point
(Figure 2b).
4. Lift the HDD assembly out of the computer.
5. Reverse the process to install a new hard disk.
Figure 2
HDD Assembly
Assembly Removal
a. Remove the 4 screws.
b. Disconnect the HDD ca-
ble and lift the HDD assembly out of the bay.
1 4 5
6
7
!
5. Hard Disk Cover
7. Hard Disk
•4 Screws
1
2
3
4
6
!
HDD System Warning
New HDD’s are blank. Before
you begin make sure:
You have backed up any data
you want to keep from your old
HDD.
You have all the CD-ROMs
and FDDs required to install
your operating system and
programs.
If you have access to the internet, download the latest application and hardware driver
updates for the operating system you plan to install. Copy
these to a removable medium.
7
5
a. b.
Disassembly
2 - 10 Removing the System Memory (RAM)
2.Disassembly
Removing the System Memory (RAM)
The computer has two memory sockets for 200 pin Small Outline Dual In-line Memory Modules (SO-DIMM) supporting
DDR 200/266/333MHz. The main memory can be expanded up to 1024MB. The SO-DIMM modules supported are
128Mb, 256Mb, and 512Mb. The total memory size is automatically detected by the POST routine once you turn on your
computer.
Memory Upgrade Process
1. Turn off the computer, remove the battery (page 2 - 8) and turn it over.
2. Remove screws - (Figure 3a) from the memory socket cover
.
3. Carefully lift up the memory socket cover (Figure 3b) (a fan cable is still attached to the mainboard and you
can disconnect it).
4. If there is a module currently installed which needs to be upgraded/replaced then remove it.
Figure 3
Memory Socket
Cover Removal
a. Remove the screws.
b. Carefully lift the cover off
the computer.
1 6
7 8
1
2
54
3
6
8
a.
7
b.
!
7. Socket Cover
•6 Screws
Loading...