Clevo A110SU, A110SU-T User guide

V13.2.00

Preface

Notice

The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. This publication and any accompanying software may not, in whole or in part, be reproduced, translated, transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer or creators of this publication, except for copies kept by the user for backup purposes. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. ©November 2013

Trademarks

Intel, Pentium and Intel Core are trademarks/registered trademarks of Intel Corporation.

Preface

R&TTE Directive

This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC.

This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia.

ErP Off Mode Power Consumption Statement:

The figures below note the power consumption of this computer in compliance with European Commission (EC) regulations on power consumption in off mode

• Off Mode < 0.5W

Preface

CE Marking

This device has been tested to and conforms to the regulatory requirements of the European Union and has attained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation. The CE Mark is obligatory for products it applies to: the manufacturer affixes the marking in order to be allowed to sell his product in the European market.

This product conforms to the essential requirements of the R&TTE directive 1999/5/EC in order to attain CE Marking. A notified body has determined that this device has properly demonstrated that the requirements of the directive have been met and has issued a favorable certificate of expert opinion. As such the device will bear the notified body number 0560 after the CE mark.

The CE Marking is not a quality mark. Foremost, it refers to the safety rather than to the quality of a product. Secondly, CE Marking is mandatory for the product it applies to, whereas most q uality marking s are vo lu ntary.

III

Preface

FCC Statement

(Federal Communications Commission)

You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Re orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the service representative or an experienc ed radio/TV technician for help.

Operation is subject to the following two conditions:

1. This device may not cause interference. And

2. This device must accept any interference, including interfer ence that may cause undesired operation of the

device.

Preface



Warning

Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standard s could void your authority to operate the equipment.

FCC RF Radiation Exposure Statement:

1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Preface

IMPORTANT SAFETY INSTRUCTIONS

Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment:

1. Do not use this product near water, for example n ear a ba th tub, wash bowl, kitchen sink or laundry tu b, in a wet

basement or near a swimming pool.

2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm. There

may be a remote risk of electrical shock from lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may

explode. Check with local codes for possible special disposal instructions.

5. This product is intended to be supplied by a Listed Power Unit (Full Range AC/DC Adapter – AC Input 100 -

240V, 50 - 60Hz, DC Output 19V, 4.74A, 90W).

This Computer’s Optical Device is a Laser Class 1 Product

Preface

Instructions for Care and Operation

The computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:

1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.

2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating ele-

ment. This is an electrical appliance. If water or any other liquid gets into it, the computer could be badly damaged.

3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other

strong magnetic fields. These can hinder proper performance and damage your data.

4. Follow the proper workin g procedu res for t he computer. Shut the computer down properly and don’t forget

to save your work. Remember to periodically save your data as data may be lost.

5. Take care when using peripheral devices.

VII

Preface



Power Safety

Warning

Before you undertake any upgrade procedures, make sure that you have turned off the power, and disconnected all peripherals and cables (including telephone lines and power cord).

You must also remove your battery in order to prevent accidentally turning the machine on. Before removing

the battery disconnect the AC/DC adapter from the computer.

Power Safety

The computer has specific power requirements:

•When you want to unplug the power cord, be sure to disconnect it by the plug head, not by its wire.

•Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.

VIII

•Before cleaning the computer, make sure it is disconnected from any external power supplies.

Do not plug in the power cord if you are wet.

Do not use the power cord if it is broken.

Do not place heavy objects on the power cord.

Preface

Polymer Battery Precautions

Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf.

• Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha-

nism and is not a cause for concern.

• Use proper handling procedures when using polymer batteries. Do not use polymer batteries in high ambient tempera-

ture environments, and do not store unused batteries for extended periods.

See also the general battery precautionary information overleaf for further information.

Preface



Battery Disposal & Caution

The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery in to the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalen t type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Battery Precautions

• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.

• Do not remove any batteries from the computer while it is powered on.

• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even

if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

• If you do not use the battery for an extended period, then remove the battery from the computer for storage.

• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.

• Do not try to repair a battery pack. Refer any battery pack repa ir or replacemen t to you r service repre sentati ve or qu al-

ified service personnel.

• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully. Batteri es

may explode or leak if exposed to fire, or improperly handled or discarded.

• Keep the battery away from metal appliances.

• Affix tape to the battery contacts before disposing of the battery.

• Do not touch the battery contacts with your hands or metal objects.

Cleaning



Removal Warning

When removing any cover(s) and screw(s) for the purposes of device upg rade, remember to replace the cover(s) and screw(s) before restoring power to the system.

Also note the following when the cover is removed:

• Hazardous moving parts.

• Keep away from moving fan blades.

Do not apply cleaner directly to the computer, use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.

Servicing

Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:

• When the power cord is damaged or frayed.

• If the computer has been exposed to any liquids.

• If the computer does not work normally when you follow the operating instructions.

• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).

• If there is an unusual odor, heat or smoke coming from your computer.

Preface

Ergonomics

We designed your Multimedia PC system to be functional as well as attractive. To get most out of it, here are some suggestions on how to position and use the computer:

• The top third of the LCD (screen) should be at eye-level or slightly below.

• The LCD should be at least 18"/45cm. directly in front of you.

• If the screen resolution makes you strain to read, then adjust the resolution to something more co mfortable (see “Video

Features” on page 1 - 35).

• Angle the LCD (see “Tilting the LCD Screen” on page 1 - 8) so that it doesn’t reflect any light into your eyes.

• Use a chair which offers good back support (especially lower-back). The seat should allow your feet to rest flat on the

floor or on a footrest directly in front of you.

• If possible, illuminate your work area with natural daylight or use a steady-glowing (non-flickering) light source.

• Place the keyboard and mouse so that your arms are at your sides and your forearms are roughly parallel to the floor.

Your wrists should flex slightly downward as you work. Your neck and shoulders should also be relaxed.

• T ake a break from the computer. Get up, stretch, flex your wrists, walk about, and look at something else for about 10

minutes every hour.

XII

Preface



Carrying the Computer

We strongly recommend using both hands to move the computer (one hand gripping the handle area and the other gripping the computer) to avoid accidentally dropping it. Be careful that objects such as belt buckles etc. do not scratch the screen while it is being carried.

Lighting

Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders.

• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.

• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.

• Position the display directly in front of you at a comfortable viewing distance.

• Adjust the display-viewing angle to find the best position.

LCD Screen Care

To prevent image persistence on LCD monitors (caused by the continuous display of graphics on the screen for an extended period of time) take the following precautions:

• Set the Windows Power Plans to turn the screen off after a few minutes of screen idle time.

• Use a rotating, moving or blank screen saver (this prevents an image from being displayed too long).

• Rotate desktop background images every few days.

• Turn the monitor off when the system is not in use.

XIII

Preface

Wall Mounting Information

The computer may be mounted on a wall for display. The system meets VESA MIS-D Standard (100mm * 100mm) for wall mounting. However if you intend to wall mount the system please contact your service center for information in order to avoid personal injury, or damage to the computer.

XIV

Preface

Contents

Notice .............................................................................................................................................................I

ErP Off Mode Power Consumption Statement: ...........................................................................................II

FCC Statement ............................................................................................................................................IV

FCC RF Radiation Exposure Statement: .....................................................................................................V

Instructions for Care and Operation ......................................................................................................... VII

Power Safety ............................................................................................................................................VIII

Polymer Battery Precautions ......................................................................................................................IX

Battery Precautions ......................................................................................................................................X

Cleaning ......................................................................................................................................................XI

Servicing .....................................................................................................................................................XI

Ergonomics ............................................................................................................................................... XII

Wall Mounting Information .....................................................................................................................XIV

Quick Start Guide - Windows 8.1

Overview ....................................................................................................................................................1-1

Advanced Users .........................................................................................................................................1-2

Beginners and Not-So-Advanced Users ....................................................................................................1-2

Warning Boxes ..........................................................................................................................................1-2

Not Included ..............................................................................................................................................1-3

System Software ........................................................................................................................................1-4

System Startup ...........................................................................................................................................1-5

Preface

System Map: Front View - Model A .........................................................................................................1-6

System Map: Front View - Model B .........................................................................................................1-7

Tilting the LCD Screen ..............................................................................................................................1-8

Buttons & LED Indicators .......................................................................................................................1-10

System Map: Left View ...........................................................................................................................1-11

HDMI-In Port ..........................................................................................................................................1-12

Mode Toggle ............................................................................................................................................1-12

Menu Button ............................................................................................................................................1-13

HDMI-In Port in Sleep or Hibernate Modes ...........................................................................................1-15

System Map: Right View .........................................................................................................................1-16

System Map: Rear View ..........................................................................................................................1-17

Wireless Keyboard & Mouse USB Transceiver ......................................................................................1-18

Windows Touch Screen Controls/Gestures .............................................................................................1-19

Touch Keyboard ......................................................................................................................................1-21

Keyboard Shortcuts - Windows 8.1 .........................................................................................................1-23

Windows 8.1 Control Panel .....................................................................................................................1-24

Windows 8.1 Start Screen & Desktop .....................................................................................................1-26

The Charms Bar .......................................................................................................................................1-29

Windows 8.1 Control Panel .....................................................................................................................1-31

Windows 8.1 Taskbar ..............................................................................................................................1-34

Video Features .........................................................................................................................................1-35

Power Options .........................................................................................................................................1-38

XVI

Preface

Running Apps ..........................................................................................................................................1-39

Features & Components

Overview ....................................................................................................................................................2-1

Hard Disk Drive .........................................................................................................................................2-2

Optical (CD/DVD) Device ........................................................................................................................2-3

Loading Discs ............................................................................................................................................2-3

Handling CDs or DVDs .............................................................................................................................2-4

DVD Regional Codes ................................................................................................................................2-5

Multi-in-1 Card Reader ..............................................................................................................................2-6

ExpressCard Slot .......................................................................................................................................2-7

Inserting and Removing ExpressCards ......................................................................................................2-7

...................................................................................................................................................................2-7

Audio Features ...........................................................................................................................................2-8

Setup for Audio Recording ........................................................................................................................2-9

Power Management

Overview ....................................................................................................................................................3-1

The Power Sources ....................................................................................................................................3-2

AC/DC Adapter .........................................................................................................................................3-2

Battery ........................................................................................................................................................3-2

Turning On the Computer ..........................................................................................................................3-3

Shutting the Computer Down ....................................................................................................................3-4

XVII

Preface

Power Plans ...............................................................................................................................................3-5

Power-Saving States ..................................................................................................................................3-7

Sleep ..........................................................................................................................................................3-7

Hibernate ....................................................................................................................................................3-8

Shut down ..................................................................................................................................................3-8

Configuring the Power Buttons .................................................................................................................3-9

Resuming Operation ................................................................................................................................3-11

Battery Information .................................................................................................................................3-13

Conserving Battery Power .......................................................................................................................3-14

Battery Life ..............................................................................................................................................3-15

New Battery .............................................................................................................................................3-15

Recharging the Battery with the AC/DC Adapter ...................................................................................3-15

Proper handling of the Battery Pack ........................................................................................................3-16

Battery FAQ .............................................................................................................................................3-17

Drivers & Utilities

What to Install ............................................................................................................................................4-1

Driver Installation (Windows 8.1) .............................................................................................................4-2

Updating/Reinstalling Individual Drivers ..................................................................................................4-5

User Account Control ................................................................................................................................4-6

Windows Security Message .......................................................................................................................4-6

New Hardware Found ................................................................................................................................4-6

XVIII

Preface

Driver Installation Procedure .....................................................................................................................4-7

Chipset .......................................................................................................................................................4-7

Video ..........................................................................................................................................................4-7

LAN ...........................................................................................................................................................4-7

Card Reader ...............................................................................................................................................4-7

System Brightness AP ...............................................................................................................................4-7

Airplane .....................................................................................................................................................4-7

MEI Driver .................................................................................................................................................4-7

Audio .........................................................................................................................................................4-8

Optional Drivers ........................................................................................................................................4-9

BIOS Utilities

Overview ....................................................................................................................................................5-1

The Setup Utility ........................................................................................................................................5-2

Failing the POST .......................................................................................................................................5-3

Fatal Errors ................................................................................................................................................5-3

Non-Fatal Errors ........................................................................................................................................5-3

Setup Screens .............................................................................................................................................5-4

Main Menu .................................................................................................................................................5-5

System Time & Date (Main Menu) ...........................................................................................................5-5

SATA Port # (Main Menu) ........................................................................................................................5-6

System/Extended Memory: (Main Menu) .................................................................................................5-6

XIX

Preface

ME FW Version / MB Series / BIOS Revision / KBC/EC firmware Revision .........................................5-6

Advanced Menu .........................................................................................................................................5-7

Intel(R) Anti-Theft Technology (Advanced Menu) ..................................................................................5-7

SATA Mode Selection (Advanced Menu) ................................................................................................5-8

Boot Logo (Advanced Menu) ....................................................................................................................5-8

Power On Boot Beep (Advanced Menu) ...................................................................................................5-8

Battery Low Alarm Beep (Advanced Menu) .............................................................................................5-8

Security Menu ............................................................................................................................................5-9

Set Supervisor Password (Security Menu) ................................................................................................5-9

Set User Password (Security Menu) ........................................................................................................5-10

Password on boot: (Security Menu) ........................................................................................................5-10

Secure Boot Control (Security Menu) .....................................................................................................5-10

Boot Menu ...............................................................................................................................................5-11

Boot Option Priorities (Boot Menu) ........................................................................................................5-12

UEFI Boot (Boot Menu) ..........................................................................................................................5-12

Exit Menu ................................................................................................................................................5-13

Upgrading The Computer

Overview ....................................................................................................................................................6-1

When Not to Upgrade ................................................................................................................................6-2

Removing the Battery ................................................................................................................................6-3

Inserting the Battery ..................................................................................................................................6-5

Preface

Removing the Rear Component Cover ......................................................................................................6-6

Inserting the Rear Cover ............................................................................................................................6-8

Upgrading the Hard Disk Drive/SSD ........................................................................................................6-9

Removing the 3.5" (88.9mm) HDD .........................................................................................................6-10

Replacing the Brackets & Screws in the 3.5" (88.9mm) HDD ...............................................................6-12

Removing the 2.5" (63.5mm) HDD or SSD ............................................................................................6-14

Upgrading the Optical (CD/DVD) Device Drive ....................................................................................6-17

Upgrading the System Memory (RAM) ..................................................................................................6-18

Upgrading the Processor ..........................................................................................................................6-21

Modules & Options

Overview ....................................................................................................................................................7-1

PC Camera Module ....................................................................................................................................7-2

PC Camera Audio Setup ............................................................................................................................7-3

Camera App ...............................................................................................................................................7-4

Camera Options .........................................................................................................................................7-5

Taking Pictures/Capturing Video ..............................................................................................................7-6

Camera Roll ...............................................................................................................................................7-7

Wireless LAN Module .............................................................................................................................7-11

3rd Party 802.11b/g/n Driver Installation ................................................................................................7-12

Intel® WLAN Driver Installation ............................................................................................................7-12

WLAN Configuration in Windows .........................................................................................................7-13

XXI

Preface

Bluetooth & WLAN Combo Module ......................................................................................................7-16

3rd Party Bluetooth (V4.0) Combo Driver Installation ...........................................................................7-17

Intel Bluetooth Combo Driver Installation ..............................................................................................7-17

Bluetooth Configuration in Windows ......................................................................................................7-18

Trusted Platform (Security) Module ........................................................................................................7-21

Enabling & Activating TPM ....................................................................................................................7-22

Trusted Platform Module (TPM) Driver Installation ..............................................................................7-24

Initializing TPM .......................................................................................................................................7-25

Infineon Security Platform Settings Tool ................................................................................................7-27

Wireless Display ......................................................................................................................................7-35

Wireless Display Configuration ..............................................................................................................7-36

Troubleshooting

Overview ....................................................................................................................................................8-1

Basic Hints and Tips ..................................................................................................................................8-2

Backup and General Maintenance .............................................................................................................8-3

Viruses .......................................................................................................................................................8-4

Upgrading and Adding New Hardware/Software ......................................................................................8-5

Problems & Possible Solutions ..................................................................................................................8-7

Interface (Ports & Jacks)

Overview ...................................................................................................................................................A-1

Computer Ports and Jacks .........................................................................................................................A-2

XXII

Preface

Card Reader Port .......................................................................................................................................A-2

DC-In Jack ................................................................................................................................................A-2

External Monitor (VGA) Port ...................................................................................................................A-2

HDMI-In Port ...........................................................................................................................................A-2

HDMI-Out Port .........................................................................................................................................A-2

Headphone-Out Jack .................................................................................................................................A-3

Microphone-In Jack ..................................................................................................................................A-3

PS/2 Type Keyboard & Mouse Ports ........................................................................................................A-3

RJ-45 LAN Jack .......................................................................................................................................A-3

RS-232 COM/Serial Ports ........................................................................................................................A-4

Security Lock Slot ....................................................................................................................................A-4

USB 2.0/1.1 Ports .....................................................................................................................................A-4

USB 3.0 Port .............................................................................................................................................A-4

Intel Video Driver Controls

Intel Video Driver Installation ..................................................................................................................B-1

Video .........................................................................................................................................................B-1

Dynamic Video Memory Technology ......................................................................................................B-1

Intel® HD Graphics Control Panel ...........................................................................................................B-2

Display Devices & Options ....................................................................................................................B-15

Specifications

Processor ...................................................................................................................................................C-2

XXIII

Preface

Core Logic ................................................................................................................................................C-2

Display ......................................................................................................................................................C-2

Memory .....................................................................................................................................................C-2

Video Adapter ...........................................................................................................................................C-2

BIOS .........................................................................................................................................................C-2

Storage ......................................................................................................................................................C-3

Audio ........................................................................................................................................................C-3

Interface ....................................................................................................................................................C-3

Card Reader ..............................................................................................................................................C-3

Slots ..........................................................................................................................................................C-3

Communication .........................................................................................................................................C-3

Power Management ..................................................................................................................................C-3

Power ........................................................................................................................................................C-4

Security .....................................................................................................................................................C-4

Operating System ......................................................................................................................................C-4

Design Features ........................................................................................................................................C-4

LED Indicators ..........................................................................................................................................C-4

Environmental Spec ..................................................................................................................................C-4

Physical Dimensions & Weight ................................................................................................................C-4

XXIV

Quick Start Guide

Chapter 1: Quick Start Guide - Windows 8.1

Overview

This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following:

• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,

optical device, Multi-in-1 card reader, ExpressCard/34/54) Audio & Printer.

• Chapter 3 The computer’s power saving options.

• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the

computer’s subsystems.

• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).

• Chapter 6 Instructions for upgrading your computer.

• Chapter 7 A quick guide to the computer’s PC Camera, Wireless LAN, Bluetooth & WLAN Combo and

Trusted Platform (Security) modules (some of which may be optional depending on your purchase configuration).

• Chapter 8 A troubleshooting guide.

• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external

devices.

• Appendix B Information on the Intel video driver controls.

• Appendix C The computer’s specification.

Overview 1 - 1



Notes

Check the light colored boxes with the mark above to find detailed information about the computer’s features.

Quick Start Guide

Advanced Users

If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on

page 6 - 1 in the User’s Manual. You may also find the notes marked with a

 of interest to you.

Beginners and Not-So-Advanced Users

If you are new to computers (or do not have an advanced knowledge of them) then the information contained in this Quick Start Guide should be enough to get you up and running. Eventually you should try to look through all the documentation (more detailed descriptions of the functions, setup and system controls are covered in the remainder of the User’s Manual), but do not worry if you do not understand everything the first time. Keep this manual nearby and refer to it to learn as you go. You may find it useful to refer to the notes marked with a

 as indicated in the margin.

For a more detailed description of any of the interface ports and jacks see “Interface

(Ports & Jacks)” on page A - 1.

Warning Boxes

No matter what your level please pay careful attention to the warning and safety information indicated by the

 symbol. Also please note the safety and handling instructions as indicated in the Preface.

1 - 2 Overview

Quick Start Guide



Drivers

If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order listed in Table 4 - 1, on page 4 - 4. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.

Ports and Jacks

See “Computer Ports and Jacks” on page A - 2 for a description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc.

Not Included

Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.

Overview 1 - 3



Windows Versions

Note that the information included on the following pages is for Windows 8.1 only. The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is pro -

vided on the Device Drivers & Manual Disc with reference to Windows 8.

Windows OS

In order to run Windows 8/8.1 (32 Bit) without limitations or decreased performance, yo ur computer requires a minimum

1GB of system memory (RAM), however if you are running Windows 8/8.1 (64 bit) your computer requires a minimum 2GB of system memory (RAM).

Quick Start Guide

System Software

Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 o perating system is supported.

Note: In order to run Windows without limitations or decreased performance, your computer requires a mini- mum 1GB of system memory (RAM).

1 - 4 Overview

Quick Start Guide

Power Button (located along the bottom of the LCD)



Shutdown

Note that you should always shut your computer down by choosing the Shut Down command in Windows (see page

1 - 38). This will help prevent hard disk or system problems.

System Startup

1. Remove all packing materials, CDs/DVDs and floppy disks etc.

2. Securely attach any peripherals you want to use with the computer to their ports (e.g keyboard and mouse e tc.)

3. Attach the AC/DC adapter to the DC-In jack at the rear of the LCD, then plug the AC power cord into an outlet,

and connect the AC power cord to the AC/DC adapter.

4. Push the power button at the front of the computer (along the bottom of the LCD) to turn the computer “on”.

Figure 1 - 1 - AC/DC Adapter Plugged-In/Power Button

System Startup 1 - 5

1. Optional Built-I n PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD

5. Power Button

6. Function Buttons

7. Power & System Activity LED Indicators

8. Speakers

567



Multi Touch Screen

Note that Model B computers incorporate a touch screen, Model A computers do not.

Quick Start Guide

System Map: Front View - Model A

1 - 6 System Map: Front View - Model A

Figure 1 - 2 - Front View - Model A

System Map: Front View - Model B

1. Optional Built-I n PC Camera

2. PC Camera LED

3. Built-In Microphone

4. LCD with Multi Touch Screen

5. Power Button

6. Function Buttons

7. Power & System Activity LED Indicators

8. Speakers



Multi Touch Screen

Note that Model B computers incorporate a touch screen, Model A computers do not.

567

Quick Start Guide

Figure 1 - 3 - Front View - Model B

System Map: Front View - Model B 1 - 7



Moving the Computer

We strongly recommend using both hands to move the computer. You can use one hand to grip the computer by the stand, and the other to hold the top of the LCD screen.

It is recommended that you carry the computer with the LCD facing your body to avoid scratching the surface against other objects. However take care not to scratch the LCD with any personal items, belt fittings or jewelry etc.(one hand gripping the stand and the other gripping the top of the computer to avoid accidentally dropping it).

15°

Adjust the stand to tilt the computer to 15° from the vertical position.

Quick Start Guide

Tilting the LCD Screen

It is possible to tilt the LCD screen in order to get the best possible viewing angle of the screen without glare etc.

1. Place one hand at the top of the computer , and use the other to open the stand to an angle of around 15 degrees from the vertical position (the stand will allow you to adjust to the appropriate angle if you pull it

out and let it spring back).

1 - 8 Tilting the LCD Screen

Figure 1 - 4 - Adjust the Stand

Quick Start Guide

Apply pressure from the top of the screen to adjust the stand outwards (up to 50° from the vertical position).



DVD Operation

Note that although the computer may be tilted up to an angle of 50 degrees from the vertical position, the DVD-ROM drive will only work (i.e continue to spin and read DVDs) up until an angle of around 35 degrees from the vertical position.

If you have any problems with the system reading DVDs, adjust the tilt angle accordingly.

50°

2. Apply pressure with one hand at the to p (at point ) of the computer (while holding on to the side with the other hand) to carefully push the LCD screen down in order to tilt it to the appropriate viewing angle (up to 50 degrees from the vertical position).

3. Use one hand at the top of the compu ter (while holding on to the side with th e other hand) to move the compu ter back to the original position.

Figure 1 - 5 - LCD Screen Tilt

Tilting the LCD Screen 1 - 9

Quick Start Guide

Buttons & LED Indicators

The buttons located under the front panel icons allow you to make screen and input adjustments.

Figure 1 - 6 - Front Icons

Icon Description

Decrease/Increase Buttons - Use these

buttons to decrease/increase the brightness

Menu Toggle - Use this button to bring up

the on screen menu when HDMI devices

are plugged in

When no HDMI devices are plugged in this

button acts as an Airplane Mode switch

Mode Toggle - Use this button to toggle

between the computer and HDMI Input

modes (see “Mode Toggle” on page 1 - 12)

The LED indicators on the computer display helpful information about the current status of the computer.

Icon Color Description

Orange AC/DC Power is Plugged In

Green The Computer is On

Blinking

Green

Orange The Battery is Charging

Blinking

Orange

Blank The Battery is Fully Charged

Green

Green System Activity

Green

Table 1 - 2 - LED Indicators

The Computer is in Sleep Mode

The Battery has Reached

Critically Low Power Status

HDMI Cable Plugged-In (if the

computer is off - see page 1 - 12)

Airplane Mode is ON

(the WLAN & Bluetooth Modules

are OFF)

Table 1 - 1 - Function Buttons

1 - 10 Buttons & LED Indicators

System Map: Left View

Figure 1 - 7

Left View

1. Stand

2. Multi-in-1 Card Reader

3. ExpressCard Slot (see page 2 - 7)

4. 2 * USB 3.0 Ports

5. HDMI-in Port

6. HDMI-Out Port



ExpressCard Slot

The ExpressCard Slot accepts either Express-

Card/34 or ExpressCard/54 formats.



HDMI-In Port

Note that the HDMI-In Port supports video and audio signals from attached HDMI devices.

Multi-in-1 Card Reader

The card reader allows you to use the most

popular digital storage card formats:

MMC (MultiMedia Card) / RSMMC

SD (Secure Digital) / Mini SD / SDHC / SDXC

Compatible

MS (Memory Stick) / MS Pro / MS Duo

USB 3.0 Port

The USB 3.0 port is denoted by its blue color; USB 2.0 ports are colored black.

ExpressCard Slot

The ExpressCard Slot accepts either ExpressCard/34 or ExpressCard/54 formats.

Quick Start Guide

System Map: Left View 1 - 11

Quick Start Guide

HDMI-In Port

This computer features an HDMI (High-Definition Multimedia Interface) input port that allows you to display external sources such as Blu-ray players, DVDs, set top boxes and games consoles etc. on your computer screen.

The computer itself does not need to be powered on to display video and audio from external HDMI input sources. As long as the computer is plugged-in to a power source using the AC/DC adapter (the HDMI-In port will not function under battery power), simply plug-in the HDMI cable from the external device to the com-

puter’s HDMI-In port and the computer will act as the display device.

Mode Toggle

Press and hold the mode toggle button to switch between the computer and HDMI input modes. When the HDMI input source is displayed you can use any HDMI device plugged in to the computer’s HDMI-In port. A quick press of the button will toggle the display on/off.

When the HDMI cable is plugged-in, and the computer is powered off, the battery/HDMI icon will be green when you press and hold the mode toggle button . When the HDMI device is playing the icon will then return to indicate the battery charge status. See Table 1 - 3, on page 1 - 14 for details.

1 - 12 HDMI-In Port

Quick Start Guide



HDMI Cable Removal in

Hibernate or Sleep Modes

Note that (as part of the power saving feature) if the computer is in Sleep or Hibernate modes, and the HDMI cable is removed from the HDMI-In port, any settings adjusted in the Main Menu will revert to the default settings when the HDMI cable is plugged-in again.

It is recommended that you shut the computer down by choosing the Shut Down (see page 1 - 38) command in Windows befo re removing the HDMI cable.

Figure 1 - 8 - Main Menu (If HDMI Device is Connected)

Menu Button

Press and hold the menu button when an HDMI device is connected (when no HDMI device is connected the button as an Airplane Mode toggle) to the HDMI-In port to bring up the on screen menu. This menu allows you to adjust the Luminance, Color, Volume, On Screen Display and interface Language. Use the decrease/ increase buttons to move up and down the menus, use the menu button to select an item and use the decrease/increase buttons to make adjustments.

HDMI-In Port 1 - 13

Quick Start Guide

The following table indicates the standard functions when an HDMI cable is plugged in to the HDMI-In port (and the computer is powered on/off). See overleaf for information if the computer is in Hibernate or Sleep modes.

Computer Power

Status

The computer is

powered on (using the

AC/DC adapter)

The computer is

powered off (but is

plugged in to the AC/DC

adapter)

Battery/HDMI Icon

Indicates battery charge status

only

Green (when HDMI cable is

plugged-in and the Mode Toggle

Button has been pressed and

held to select HDMI input)

When the HDMI source is playing

the icon will indicate battery

charge status only

Mode Toggle Button

(Press & Hold)

Toggles between computer

display and HDMI input

Toggles between computer

display and HDMI input

Mode Toggle Button

(Quick Press)

Toggles the display on/off

Table 1 - 3 - Mode Toggle Functions when HDMI Cable is Plugged-In (Computer Off/On)

Note that if no HDMI cable is plugged-in to the HDMI-In port, and the system is off, or in Hibernate mode, then only the power button will function.

1 - 14 HDMI-In Port

Quick Start Guide

HDMI-In Port in Sleep or Hibernate Modes

Note that if the computer is in Sleep or Hibernate modes, and no HDMI cable is plugged-in, then the procedure for plugging-in the HDMI cable and using the system as a display device is as follows:

1. The System is in Sleep or Hibernate mode and no HDMI cable is plugged-in.

2. The battery/HDMI icon will be off.

3. Plug-in the HDMI cable.

4. The battery/HDMI icon will turn green for about 8 seconds and then turn off again.

5. Press the Mode Toggle Button .

6. The battery/HDMI icon will turn green again.

7. After a few seconds the system will display the image from the external HDMI source.

HDMI-In Port 1 - 15

2 3



CD/DVD Emergency Eject

If you need to manually eject a CD/DVD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. Do not use a sharpened pencil or similar object that may break and become lodged in the hole.

Figure 1 - 9 - Right View

1. Optical Device Drive Bay (for CD/DVD Device - see page 2 - 3)

2. Headphone-Out Jack

3. Microphone-In Jack

4. USB 2.0 Port

5. Stand



Changing DVD Regional Codes

Go to the Control Panel and double-click Device Manager (Hardware and Sound), then click the + next to DVD/CD-ROM drives. Double-click on the DVD-ROM de-

vice to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code. You can select your module’s region code 5 times (see “DVD Region

Note” on page 2 - 5).



Media Warning

Don’t try to remove the CD/DVD while the system is accessing it. This may cause the system to “crash”.

Quick Start Guide

System Map: Right View

1 - 16 System Map: Right View

System Map: Rear View

Figure 1 - 10

Rear View

1. Rear Component Cover

2. Stand

3. Vent/Fan Intake

4. Carrying Handle Area

5. USB Wireless Transceiver Cover (for an RF Keyboard & Mouse Kit USB Dongle -

not supplied with this model)

6. Security Lock Slot

7. Battery

8. External Monitor Port

9. RS-232 Serial Port

10.PS/2 Port (keyboard)

11.PS/2 Port (mouse)

12.DC-In Jack

13.2 * USB Ports

14.RJ-45 LAN Port



USB Port for

Wireless

Transceiver

Note that the USB port for the wireless transceiver is designed specifically for a USB dongle for an RF Keyboard & Mouse kit (not

supplied with this model).

Do not use any other USB devices in this port.

1110

Quick Start Guide

System Map: Rear View 1 - 17



USB Port for

Wireless

Transceiver

Note that the USB port for the wireless transceiver is designed specifically for a USB dongle for an RF Keyboard & Mouse kit (not

supplied with this model).

Do not use any other USB devices in this port.

Figure 1 - 11

USB Port for

Wireless Keyboard

& Mouse Kit

123

Quick Start Guide

Wireless Keyboard & Mouse USB Transceiver

If you have purchased a wireless keyboard & mouse kit (not supplied with this computer) you can use the USB port located at the bottom left of the rear cover to house

the USB transceiver dongle (do not use this port for any other device, see sidebar).

1.Remove the USB transceiver port cover by sliding it in the direction of arrow .

2.Insert the USB transceiver into the USB port.

3.Replace the cover.

1 - 18 Wireless Keyboard & Mouse USB Transceiver

Quick Start Guide

Windows Touch Screen Controls/Gestures

Model B computers incorporate a Touch Screen and this can be used to navigate through he interface in much the same way as a mouse, touchpad and keyboard. Where you see the instruction to click/double-click an item in this manual, you can choose to tap/double tap the appropriate area of the screen instead. The following gestures are useful when navigating the Windows interface.

• Swipe from the right (Access the Charms Bar) - Pull your finger from the right side of the screen (in the black area) to the left a little bit to bring up the Charms Bar.

Figure 1 - 12 - Swipe from Right & Left

• Swipe from the left (Switch apps) - If multiple apps are running you can slide your finger from the left side of the screen (in the black area) to the right to switch between apps.

• Swipe slowly from the left (Snap apps) - Perform the same action above more slowly, to drag one app out and display it side-by-side with the app that was already on your screen.

Windows Touch Screen Controls/Gestures 1 - 19

Quick Start Guide

• Swipe from left and back (Display running apps) - Slide your finger fr om the left and quickly drag it back towards the right to display a list of apps that are currently running. Tap any app to switch to it.

• Pull down from the top (Close app) - Close any running app by starting at the top area of the screen and quickly pulling your finger about halfway down the screen.

• Swipe down/up (Customize menu) - Swiping the finger a little bit down from the top, or up from the bottom of the Start screen will bring up the menu with the Customize icon. Tap the Customize icon and then select the app tiles, and slide them to any selected position to rearrange them.

Figure 1 - 13 - Swipe Up and Tap, Hold & Release (Desktop Right-Click)

• Swipe down on an item (Select/right-click) - Swipe down on any tile in the Start screen to select it and bring up additional options.

• Tap, Hold & Release (Desktop right-click) - Tap the Desktop, hold until a square icon appears, and then release to access the right click menu.

1 - 20 Windows Touch Screen Controls/Gestures

Quick Start Guide

Touch Keyboard Desktop app taskbar Icon

Select Keyboard or Writing Pad Input

Touch Keyboard

If you need to type on screen then the Touch Keyboard will pop up when required (e.g. when you need to type in an internet URL address in Internet Explorer). When the Touch Keyboard is displayed you have several display/input options and these can be accessed from the icon at the bottom right of the keyboard. To access the Touch Keyboard from the Desktop app click/tap the keyboard icon in the taskbar .

Figure 1 - 14 - Touch Keyboard

Touch Keyboard 1 - 21

Click Help

Quick Start Guide

The Touch Keyboard allows you to input text without the use of an actual keyboard., and you can use writing pad to write (continuously or one character at a time) or touch keyboard to input text. Use the Help menu for further information.

1 - 22 Touch Keyboard

Figure 1 - 15 - Touch Keyboard, Writing Pad Input & Help

Keyboard Shortcuts - Windows 8.1



Windows Logo

Keyboard Shortcut

Use the Windows logo key + D key combi- nation to switch between the Start screen and Windows Desktop.

Menu/Application

Keyboard Shortcut

When the Desktop app is running you can use the Menu/Application key on the keyboard to display the context menu as per a mouse right-click. In the Start screen this function is useful to quickly display the All Apps icon.

Table 1 - 4

Windows 8

Keyboard Shortcuts

If you are using a keyboard with this system then note the function of the Windows Logo Key & Menu/Application Key (in the Start screen). The following keyboard

shortcuts are useful for navigation/operation in Windows.

Windows Logo Key +

Tap Winkey

Description

T oggle between the S tart screen and the foremost running

app or the Windows Desktop C Display Charms menu D Switch to the Windows Desktop and toggle show Desktop

F Display file Search

I Open the Settings charm

K Open the Connect charm

L Lock the computer and display the Lock screen

P Display the Second Screen menu

Z Access the Customize Bar

Switch to the Windows desktop and launch Windows

Explorer with Computer displayed

Switch to the Windows Desktop and display the Run

dialog box

Quick Start Guide

Keyboard Shortcuts - Windows 8.1 1 - 23



Windows Versions

Note that the information included on the following pages is for Windows 8.1 only.

The Windows 8 interface is slightly different in appearance and in methods of navigation, and a separate manual is provided on the De-

vice Drivers & Manual Disc with reference to

Windows 8.

Move the mouse to the bottom left

Start ScreenDesktop app

of the screen and right-click to access the menu.

Quick Start Guide

Windows 8.1 Control Panel

Throughout this manual you will see an instruction to open the Control Panel. R

ight-click the lower left hot corner to bring up the context menu (or use the Win-

dows Logo Key + X key combination)

Desktop app or Start screen.

and select Control Panel in both the

1 - 24 Windows 8.1 Control Panel

Figure 1 - 16 - Windows Context Menu

Right-click the Start button in the Desktop app (or use the Windows Logo Key



Display Most

Recently Used

Apps

If you are in the Start screen, Desktop or an app you can move your mouse to the upper left corner of the screen to get back to the most recently used app.

To view all the most recently used Apps hover over the top left of the screen and then move the mouse down along the left side of the screen to display the list.

Move the mouse to the bottom left of the screen

and right-click the Start button to access the menu.

+ X key combination) to bring up an advanced context menu of useful features

such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.

Figure 1 - 17 - Advanced Context Menu (Right-Click Start Button)

Quick Start Guide

Windows 8.1 Control Panel 1 - 25

Desktop App

Quick Start Guide

Windows 8.1 Start Screen & Desktop

The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking

the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination). Click the arrow at the bottom of the Start screen to access Apps.

Figure 1 - 18 - Windows Start Screen

1 - 26 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Click the arrow at the bottom of the screen to access All Apps

Apps & Tiles

The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.

Accessing Pining/Unpinning All Apps

You can add and remove the tiles for apps and control panels in the Start screen. Right-click on a blank area of the Start screen, and you will see the Customize icon. Click the Customize icon to display all the installed

applications etc. Right-click any icon to bring up the menu at the bottom of the screen and you can then click the appropriate icon to pin the App to (or unpin from) the Start screen, or to the taskbar in the Desktop applica- tion (you can also open the app in a new window, run as administrator or open the file location).

Figure 1 - 19 - Customize Apps

Windows 8.1 Start Screen & Desktop 1 - 27

Move the mouse to the bottom left of the screen and click to switch back to the Start screen.

Quick Start Guide

Desktop Application

When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app. To do so move your mouse to hover over the bottom left corner of the Desktop app and left-click.

When you move to the lower left hot corner in the Start screen it will take you back to your most recently used app (if one is running).

Figure 1 - 20 - Desktop

1 - 28 Windows 8.1 Start Screen & Desktop

The Charms Bar

Move the mouse over a Charms Bar icon to activate the menu

Move the mouse to the top/lower right icons to activate the Charms Bar

The right side of the screen displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of

the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.

Quick Start Guide

Figure 1 - 21 - Start Screen with Charms Bar

Windows 8.1 Start Screen & Desktop 1 - 29



Charms Bar - TouchPad Access

To quick access the Charms Bar using the TouchPad:

1. Place your finger off the TouchPad (slightly to the right of the pad resting on the computer).

2. Move your finger across to the left on to the TouchPad.

3. The Charms Bar will then pop-up.

Quick Start Guide

Charms Bar Items

• Search : You can search for any file, application, Apps and control panel settings with instantaneous

results.

•Share : This button is used to share information with people via mail or social networks.

•Start : Click to bring up the Start screen (the same function as pressing the Windows Logo Key or click-

ing the bottom left of the screen).

• Devices : Click this button to change connected peripheral device settings e.g. an external display.

• Settings : This button gives instant access to the computer settings, such as Network, Audio, Notifications, Power and Keyboard (click Change PC Settings to activate the PC Settings menu).

Figure 1 - 22 - Settings Menu

1 - 30 Windows 8.1 Start Screen & Desktop

Quick Start Guide

Windows 8.1 Control Panel

In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 8.1.

•Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left.

Figure 1 - 23 - Search (Control Panel)

• Click on This PC (in Apps, or you can to pin This PC to the Start screen), click on Computer in the top menu and select Open Control Panel from the ribbon.

Figure 1 - 24 - Open Control Panel (Computer)

Windows 8.1 Control Panel 1 - 31

Quick Start Guide

• When in the Desktop app (this does not apply to the Start screen) click on Settings in the Windows Charms Bar and select Control Panel from the menu.

Figure 1 - 25 - Settings Charms Bar (Desktop App Only)

• Click the arrow at the bottom of the Start screen and click Control Panel in Apps (Windows System).

Figure 1 - 26 - All Apps - Control Panel

1 - 32 Windows 8.1 Control Panel

Quick Start Guide



Keyboard Shortcut to Control Panel

You can also use keyboard shortcuts to access the Contro l Pa nel. Press th e Win dows logo key and X to bring up the context menu, and then press P to bring up the Control Panel. Alternatively press the Windows logo key and R to bring up the Run dialog box, and then type “Control Panel” and press Enter to access the Control Panel.

• Right-clic k the lower left hot corner to br ing up the menu and select Control Panel (see Figure 1 - 17 on

page 1 - 25).

Windows 8.1 Control Panel 1 - 33

Quick Start Guide

Windows 8.1 Taskbar

In many instances throughout this manual you will see an instruction to access the notification area of the taskbar (system tray). In Windows 8.1 the taskbar is accessed from the Desktop application; if you are in the Start

screen you will need to switch to the Desktop. The taskbar is displayed at the bottom of the Desktop screen, and you can see the notification area (system

tray) of the taskbar in the bottom right of the screen. Some of the control panels and applications referred to during the course of this manual can be accessed from here.

Figure 1 - 27 - Desktop Taskbar & Notification Area (System Tray)

You can pin/unpin apps to/from the taskbar in much the same way as you can to the Start screen (see “Accessing

Pining/Unpinning All Apps” on page 1 - 27).

1 - 34 Windows 8.1 Control Panel

Quick Start Guide

Video Features

You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows when running the Desktop app (see “Desktop Application” on page 1 - 28 and Appendix C). It is also possible to quickly configure external displays from the Devices menu item in the Charms Bar (see “The Charms Bar” on page 1 - 29).

To Configure Displays from Devices (Charms Bar):

1. Attach your display to the appropriate port, and turn it on.

2. Go the Charms Bar, select Devices.

3. Click Project (you may need to click Second Screen).

4. Click on any one of the options from the menu to select PC screen only, Duplicate, Extend or Second screen

only.

Figure 1 - 28- Devices (Project)

Video Features 1 - 35



Right-Click Desktop App

1. You can right-click (tap and the touch screen until you see a square icon and then release your finger) the desktop and select

Screen resolution (Figure 1

- 29).

2. Use the dropbox to select the screen Resolution (Figure 1 - 29).

3. Click Advanced settings (Figure 1 -

29) to bring up the Advanced properties

tabs.

123

Quick Start Guide

To access Display (Control Panel) and Screen Resolution in Windows:

1. Go to the Control Panel.

2. Click/tap Display (icon) - In the Appearance and Personalization category.

3. Adjust resolution.

Figure 1 - 29 - Screen Resolution

1 - 36 Video Features

Quick Start Guide

To access the Intel(R) HD Graphics Control Panel:

1. Click/tap Advanced settings (Figure 1 - 29 on page 1 - 36) in the Screen Resolution control panel in Windows.

2. Click/tap the Intel(R)... tab and click/tap Graphics Properties (button) (Figure 1 - 30 on page 1 - 37) .

3. Right-click (tap, hold and release) the desktop and select Graphics Properties from the menu.

4. Click/tap the icon in the notification area of the Desktop taskbar and select Graphics Properties from the menu.

Figure 1 - 30 - Intel Graphics Control Panel

Video Features 1 - 37

Charms Bar Desktop App Start Screen

Quick Start Guide

Power Options

Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set- tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu” on page 3 - 9). You can also use the context menu (Shut down or sign out) shut the computer down/restart etc.

Shut Down, Restart or Sleep (Charms Bar)

1. Go to the Charms Bar and click Settings.

2. Click Power .

3. Select Sleep, Shut Down or Restart.

1 - 38 Power Options

Figure 1 - 31 - Shut Down/Restart

Quick Start Guide



Screen Resolution for Apps

(Windows 8.1)

The minimum resolution in which Apps will run is 1024x768. The minimum resolution required to support all the features of Windows

8 (including multitasking with snap) is 1366x768. These specs are the minimum screen resolution that supports all the

features of Windows on a useful physica l si ze.

Running Apps

To run apps in Windows you will need to check that the Screen Resolution and User Account Control Settings are compatible with the system requirements.

Screen Resolution Settings

1. Switch to the Windows Desktop (click/tap the app or use the Windows logo key + D key combination).

2. Right-click a blank area of the Windows Desktop and select Screen Resolution. Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above (see sidebar).

Figure 1 - 32 - Screen Resolution

Running Apps 1 - 39

Quick Start Guide

User Account Control Settings

If your computer meets the minimum screen resolution requirements, and still you can't run Metro apps, then that you have to check the status of User Account Control (UAC). Metro apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below.

1. Open the Control Panel.

2. Click on User Accounts and then click on Change User Account Control settings (or click System and Security and click Change User Account Control Settings under Action Center).

3. If the slider is in the Never notify position, then the UAC is disabled.

4. To enable or turn on the UAC, move the slider to Always notif y or Notify me when apps try to make changes

to my computer (default) position, and then click OK.

1 - 40 Running Apps

Figure 1 - 33 - User Account Control

Features & Components

Chapter 2: Features & Components

Overview

Read this chapter to learn more about the following main features and components of the computer:

•Hard Disk Drive

• Optical (CD/DVD) Device

• Multi-in-1 Card Reader

• ExpressCard Slot

• Audio Features

Overview 2 - 1

Features & Components



Power Safety

Before attempting to access any of the internal components of your computer please ensure that the machine is not connected to the AC power, and that the machine is turned off. Also ensure that all peripheral cables, including phone lines, are disconnected from the computer.

Figure 2 - 1

Hard Disk Location

Hard Disk Drive

The hard disk drive is used to store your data in the computer. The hard disk can be taken out to accommodate other 2.5" or 3.5" (pictured below) serial (SATA) hard disk drives with a height of 9.5 mm.

The hard disk is accessible from the rear of your computer as seen below. For further details see “Upgrading the Hard Disk Drive/SSD” on page 6 - 9.

2 - 2 Hard Disk Drive

Features & Components



Volume Adjustment

The sound volume level can be set using the volume control in the Set-

tings menu in the Charms Bar (see “Au-

dio Features” on page 2 - 8).

Figure 2 - 2

Optical Device

123

Optical (CD/DVD) Device

There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual device will depend on the module you purchased (see “Storage” on page C - 3). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 11).

Loading Discs

To insert a CD/DVD, press the open button and carefully place a CD/DVD onto the disc tray with label-side facing up (use just enough force for the disc to click onto the tray’s spindle). Gently push the CD/ DVD tray in until its lock “clicks” and you are ready to start. The busy indicator will light up while data is being accessed, or while an audio/video CD, or DVD, is playing. If power is unexpectedly interrupted, insert an object such as a straightened paper clip into the emergency eject hole to open the tray.

Optical (CD/DVD) Device 2 - 3

Features & Components



CD Emergency Eject

If you need to manually eject a CD (e.g. due to an unexpected power interruption) you may push the end of a straightened paper clip into the emergency eject hole. However please do NOT use a sharpened pencil or similar object that may break and become lodged in the hole.

Disk Eject Warning

Don’t try to remove a CD/DVD while the system is accessing it. This may cause the system to “crash”.

2 - 4 Optical (CD/DVD) Device

Handling CDs or DVDs

Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be accessed.

Note the following:

• Hold the CD or DVD by the edges; do not touch the surface of the disc.

• Use a clean, soft, dry cloth to remove dust or fingerprints.

• Do not write on the surface with a pen.

• Do not attach paper or other materials to the surface of the disc.

• Do not store or place the CD or DVD in high-temperature areas.

• Do not use benzene, thinner, or other cleaners to clean the CD or DVD.

• Do not bend the CD or DVD.

• Do not drop or subject the CD or DVD to shock.

Features & Components



DVD Region Note

DVD region detection is device dependent, not OS-dependent. You can select your module’s region code 5 times. The fifth selection is permanent. This cannot be altered even if you change your operating system or you use the module in another computer.

Figure 2 - 3

DVD Region Codes

• Region 1 - USA & Canada

• Region 2 - Western Europe, Japan,

South Africa, Middle East & Egypt

• Region 3 - South-East Asia, Taiwan,

South Korea, The Philippines, Indonesia, Hong Kong

• Region 4 - South & Central Amer-

ica, Mexico, Australia, New Zealand

• Region 5 - N Korea, Russia, Eastern

Europe, India & Most of Africa

• Region 6 - China

DVD Regional Codes

To change the DVD regional codes:

1. Go to the Control Panel

2. Double-click/tap Device Manager (Hardware and Sound), then click/tap the + next to DVD/CD-ROM drives.

3. Double-click/tap on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.

Optical (CD/DVD) Device 2 - 5

Features & Components



Card Reader Cover

Make sure you keep the cover in the card reader when not in use. This will help prevent foreign objects and/or dust getting in to the card reader.

Figure 2 - 4

Front View

1. Card Reader

The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s). Make sure you install the Card Reader driver (see

“Card Reader” on page 4 - 7

• MMC (MultiMedia Card) / RSMMC

• SD (Secure Digital) / Mini SD / SDHC / SDXC

• MS (Memory Stick) / MS Pro / MS Duo

Multi-in-1 Card Reader

2 - 6 Multi-in-1 Card Reader

Features & Components



ExpressCard Slot

Cover

Make sure you keep the cover in the ExpressCard slot when not in use. This will help prevent foreign objects and/ or dust getting in to the ExpressCard Slot.

Figure 2 - 5

ExpressCard Slot

1. ExpressCard Slot

The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/34 and

ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cards).

ExpressCard/54 is used for applications which require a larger interface slot, e.g. CompactFlash card reader. The number denotes the card width; 54mm for the Express Card/54 and 34mm for the ExpressCard/34. Make sure you install the Card Reader driver (see

“Card Reader” on page 4 - 7

Inserting and Removing ExpressCards

• Align the ExpressCard with the slot and push it in until it locks into place.

• To remove an ExpressCard, simply press the card to eject it.

ExpressCard Slot

ExpressCard Slot 2 - 7

Features & Components



Volume Adjustment

The sound volume level can be set using the volume control in the Set-

tings menu in the Charms Bar.

Figure 2 - 6

Realtek Audio

Manager

Right-click the icon to access the menu above.

Note that many keyboards have built-in controls to allow you to adjust the audio volume.

Audio Features

You can configure the audio options on your computer from the Sound control panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar notification area/control panel (right-click the taskbar notification area icon to bring up an audio menu). The volume may also be adjusted by means of the volume icon in the taskbar or the audio slider in the Settings menu (see sidebar).

2 - 8 Audio Features

Features & Components

Figure 2 - 7

Realtek Audio

Manager -

Recording Setup

Setup for Audio Recording

To record audio sources on your computer at optimum quality follow the instructions below:

1. Go to the

2. Click/tap Realtek HD Audio Manager (Hardware and Sound), or right-click the taskbar icon and select Sound Manager.

3. Click/tap Microphone Effects (tab) in Microphone (tab), and then click/tap to select Noise Suppression (button), or adjust the Recording Volume level to around 60, to obtain the optimum recording quality.

4. Click/tap OK to close the control panel and save the settings.

Control Panel

Audio Features 2 - 9

Features & Components

2-10

Chapter 3: Power Management



OS Note

Power management functions will vary slightly depending on your operating system. For more information it is best to refer to the user’s manual of your operating system.

(Note: All pictures used on the following pages are from the Windows

8.1 OS.)

Power Options

Power management in Windows is configured from Power Options (Hardware and Sound), which can be accessed from the Con- trol Panel (see page 1 -

31).

Power Management

Overview

To conserve power, especially when using the battery, your computer power management conserves power by controlling individual components of the computer (the monitor and hard disk drive) or the whole system.

This chapter covers:

• The Power Sources

• Turning On the Computer

• Shutting the Computer Down

• Power-Saving States

• Configuring the Power Buttons

• Battery Information

The computer uses enhanced power saving techniques to give the operating system (OS) direct control over the power and thermal states of devices and processors. For example, this enables the OS to set devices into low-power states based on user settings and information from applications.

Using some form of power management greatly increases the life span of the LCD.

Overview 3 - 1

Power Management

The Power Sources

The computer can be powered by either the AC/DC adapter or a battery pack.

AC/DC Adapter

Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components.

1. Attach the AC/DC adapter to the DC-In jack at the rear of the computer.

2. Plug the AC power cord into an outlet, and then conne ct the AC power co rd to the AC/DC adapter.

3. Adjust the LCD to a comfortable viewing angle.

4. Press the power button on the fro nt of the computer for about 2 - 3 seconds to turn the computer “on” (note that the power LED on the front of the computer will turn from orange to green when the computer powers on).

Battery

The battery allows you to use your computer while you are on the road or when an electrical outlet is unavailable. Battery life varies depending on the applications and the configuration you're using. To increase battery life, let the battery discharge completely before recharging (see “How do I completely discharge the battery?”

on page 3 - 17).

We recommend that you do not remove the battery. For more information on the battery, please refer to “Battery Information” on page 3 - 13.

3 - 2 The Power Sources

Turning On the Computer



Power Button as Stand by or Hibernate Button

You can use the OS’s “Power Options” control panel to set the power button to send the system into Stand by or Hibernate mode (see your OS’s documentation, or “Configuring

the Power Buttons” on page 3 - 9 for details).

Now you are ready to begin using your computer. To turn it on simply press the power button on the front panel.

When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down). Use Power Options (Hardware and Sound) in the Windows control panel to configure this feature.

Power Management

Turning On the Computer 3 - 3

Power Management

Figure 3 - 1

Shut Down/Restart

Charms Bar Desktop App Start Screen

Shutting the Computer Down

Note that you should always shut your computer down by choosing the Shut down

command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen

to bring up the menu). You can also use the Power Menu in Settings in the Windows 8.1 Charms Bar. If

you want to add Hibernate/Sleep to the Power Menu see “” on page 3 - 9.

3 - 4 Shutting the Computer Down

Power Plans



Resuming

Operation

See Table 3 - 1, on

page 3 - 11 for informa-

tion on how to resume from a power-saving state.

Password

It is recommended that you enable a password on system resume in order to protect your data.

Figure 3 - 2

Power Plan

Advanced Settings

The computer can be configured to conserve power by means of power plans. You can use (or modify) an existing power plan, or create a new one.

The settings may be adjusted to set the display to turn off after a specified time, and to send the computer into Sleep after a period of inactivity.

Click/tap Change plan settings and then click/tap Change advanced power settings to access further configuration options in Advanced Settings.

Power Management

Power Plans3-5

Power Management

Figure 3 - 3

Power Plans

Click/tap to Show/Hide additional power plans

Each Windows power plan will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power).

Choose High performance (you may need to click/tap Show additional plans to view the High performance plan) for maximum performance when the computer is powered from an AC power source. Choose the Power saver (bear in mind that this scheme may slow down the overall performance of the computer in order to save power) for maximum power saving when the computer is battery (DC power) powered.

3 - 6 Power Plans

Power-Saving States



Wake On LAN

Support

Wake-On-LAN is only supported from Sleep or

Hibernate states in Windows.

If you require your computer to wake up from network activity in Windows then make sure that the computer is either in Sleep or Hiber- nate.

Wake-On-LAN is not supported from Shutdown states in Win- dows.

You can use power-saving states to stop the computer’s operation and restart where you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving states.

Sleep

In Sleep all of your work, settings and preferences are saved to memory before the system sleeps. When you are not using your computer for a certain length of time, which you specify in the operating system, it will enter Sleep to save power.

The PC wakes from Sleep within seconds and will return you to where you last left off (what was on your desktop) without reopening the application(s) and file( s) you last used.

If your mobile PC in Sleep is running on battery power the system will use only a minimum amount of power. After an extended period the system will save all the information to the hard disk and shut the computer down before the battery becomes depleted.

To add Sleep to the Power Menu see “Adding Hibernate/Sleep to the Power

Menu” on page 3 - 10.

Power Management

Power-Saving States 3 - 7

Power Management

Figure 3 - 4

Power Menu

Hibernate

Hibernate uses the least amount of power of all the power-saving states and saves

all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost. Hi- bernate will also return you to where you last left off within seconds. You should put your mobile PC into Hibernate if you will not use the computer for a period of time, and will not have the chance to charge the battery. To add Hibernate to the Power Menu see “” on page 3 - 9.

Shut down

You should Shut down the computer if you plan to install new hardware (don’t forget to remove the battery and follow all the safety instructions in Chapter 6), plan to be away from the computer for several days, or you do not need it to wake up and run a scheduled task. Returning to full operation from Shut down takes longer than from Sleep or Hibernate.

3 - 8 Power-Saving States

Configuring the Power Buttons



Password

Protection

It is recommended that you enable a password on wake up in order to protect your data.

However you can disable this setting from the Power Options menu by clicking Require a

password on wakeup

in the left menu, and selecting the options (click/ tap Change settings

that are currently unavailable).

Figure 3 - 5

Power Options

Define Power

Buttons

The power button may be set to send the computer in to either Sleep or Hibernate. In Sleep , the LED will blink green. In Hibernate the LED will be orange. If only the display is turned off, the LED will remain green. Click/tap Choose what the power buttons do on the left menu in Power Options to bring up the menu.

Power Management

Configuring the Power Buttons 3 - 9

Power Management

Figure 3 - 6

Power Options

Define Power

Buttons - Shutdown

Settings

Adding Hibernate/Sleep to the Power Menu

Add Hibernate/Sleep to the Power Menu as follows.

1. Go to the Power Options (Hardware and Sound) control panel (see page 1 - 31).

2. Click/tap Choose what the power buttons do.

3. Click/tap to put a tick in the Hibernate/Sleep box under Shutdown settings.

4. Click/tap Save Changes and close the control panel.

3 - 10 Configuring the Power Buttons

Resuming Operation

Table 3 - 1

Resuming

Operation



Power Button

When the computer is on, you can use the power button as a Sleep/Hibernate/Shut Down hot key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will force the computer to shut down).

You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (see your keyboard documentation).

Power Management

Power Status

Power Off Off Press the Power Button

Sleep Blinking Green

Hibernate

Display Turned Off Green Press a Key or Move the Mouse

Icon Color

(see your keyboard documentation)

Off (battery)

Orange (AC/DC adapter)

To Resume

Press the Power Button

Press the Sleep Button

Press the Power Button

Configuring the Power Buttons 3 - 11

Power Management

Figure 3 - 7

Ctrl + Alt + Delete

Ctrl + Alt + Delete Key Combination

You can use the CTRL + ALT + DEL key combination from almost any of the Windows interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log

off, Change a password and Task Manager options. If you click/tap the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.

To fully control all the power options (including Hibernate mode) go to the Power Options control panel and configure the power button and sleep button to perform the function selected.

3 - 12 Configuring the Power Buttons

Battery Information



Low Battery

Warning

When the battery is critically low, immediately connect the AC/DC adapter to the computer or save your work, otherwise, the unsaved data will be lost when the power is depleted.

Figure 3 - 8

Battery Icon

(Notification Area) &

Battery Advanced

Settings

Follow these simple guidelines to get the best use out of your battery.

Battery Power

Your computer’s battery power is dependent upon many factors, including the programs you are running, and peripheral devices attached. You can set actions to be taken (e.g. Shut down, Hibernate etc.), and set critical and low battery levels from power plan Change plan settings > Change advanced power settings (see Figure

3 - 2 on page 3 - 5).

Click/tap the battery icon in the notification area to see the current battery level and charge status.

Power Management

Battery Information 3 - 13

Power Management



Windows Mobility

Center

The Windows Mobility Center (Hardware and Sound) control panel

provides an easy point of access for information on battery status, power plans used and wireless device status etc.

Figure 3 - 9

Windows Mobility

Center

Conserving Battery Power

•Use a power plan that conserves power (e.g Power saver), however note that

this may have an affect on computer performance.

• Lower the brightness level of the LCD display. The system will decrease LCD

brightness slightly to save power when it is not powered by the AC/DC adapter.

• Reduce the amount of time before the display is turned off.

• Close wireless, Bluetooth, modem or co mmunication applications when they are

not being used (e.g. put the system in Airplane Mode).

• Disconnect/remove any unnecessary external devices e.g. USB devices.

3 - 14 Battery Information

Battery Life

Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days.

We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason (e.g. long term storage) see “Removing the Battery”

on page 6 - 3.

New Battery

Always completely discharge, then fully charge, a new battery (see “Battery FAQ”

on page 3 - 17 for instructions on how to do this).

Recharging the Battery with the AC/DC Adapter

The battery pack automatically recharges when the AC/DC adapter is attached and plugged into an electrical outlet. If the computer is powered on, and in use, it will take several hours to fully recharge the battery. When the computer is turned off but plugged into an electrical outlet, battery charge time is less. (Refer to “Buttons &

LED Indicators” on page 1 - 10 for information on the battery charge status, and to “Battery FAQ” on page 3 - 17 for more information on how to maintain and prop-

erly recharge the battery pack.)

Power Management

Battery Information 3 - 15

Power Management



Damaged Battery Warning

Should you notice any physical defects (e.g. the battery is bent ou t of shape after being dropped), or any unusual smells emanating from the notebook battery, shut your computer down immediately and contact your distributor/supplier. If the battery has been dropped we do not recommend using it any further, as even if the comp uter continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire. It is recommended that you replace your computer battery every two years.



Caution

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the manufacturer. Discard used battery according to the manufacturer’s instructions.

Proper handling of the Battery Pack

• DO NOT disassemble the battery pack under any circumstances.

• DO NOT expose the battery to fire or high temperatures, it may explode.

• DO NOT connect the metal terminals (+, -) to each other.

3 - 16 Battery Information

Battery FAQ

Figure 3 - 10

Power Plan Create

How do I completely discharge the battery?

Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.

1. Save and close all files and applications.

2. Create a power plan for discharging the battery and set all the options to Never.

Power Management

Battery Information 3 - 17

Power Management

Figure 3 - 11

Change Plan

Settings / Change

Advanced Power

Settings

3. Click/tap Change plan settings (after creating it) and click/tap Change plan settings > Change advanced power settings.

3 - 18 Battery Information

4. Scroll down to Battery and click/tap + to expand the battery options.

Figure 3 - 12

Power Options

Advanced Settings -

Battery

5. Choose the options below (click/tap Yes if a warning appears):

• Low battery levels = 0%

• Critical battery Levels = 1%

• Low battery action = Do Nothing

• Critical battery action (On battery) = Shut Down

• Critical battery action (Plugged in) = Do Nothing

Power Management

Battery Information 3 - 19

Power Management

How do I fully charge the battery?

When charging the battery, don’t stop until the LED charging indicator light changes from orange to green.

How do I maintain the battery?

Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.

3 - 20 Battery Information

Chapter 4: Drivers & Utilities



Driver Installation &

Power

When installing drivers make sure your computer is powered by the AC/DC adapter connected to a working power source.

Some drivers draw a significant amount of power during the installation procedure, and if the remaining battery capacity is not adequate this may cause the system to shut down and cause system problems (note that there is no safety issue involved here, and the battery will be rechargeable within 1 minute).

This chapter deals with installing the drivers and utilities essential to the operation or improvement of some of the computer’s subsystems. The system takes advantage of some newer hardware components for which the latest versions of most available operating systems haven’t built in drivers and utilities. Thus, some of the system components won’t be auto-configured with an appropriate driver or utility during operating system installation. Instead, you need to manually install some system-required drivers and utilities.

What to Install

The Device Drivers & Utilities + Use r’s Manual disc contains the drivers and util- ities necessary for the proper operation of the computer. Table 4 - 1, on page 4 - 4 lists what you need to install and it is very important that the drivers are installed in the order indicated.

Note that the information included on the following pages is for Windows 8.1 only.

The procedures for installing drivers for the PC Camera, Wireless LAN and Blue- tooth & WLAN Combo modules are provided in “Modules & Options” on page 7

- 1.

Drivers & Utilities

What to Install 4 - 1

Drivers & Utilities



Driver Installation

If you miss the message above you can eject the Device Drivers & Utilities + User’s Manual disc and then

reinsert it. Alternatively double-click/tap the disc icon in Com-

puter (use the Windows logo key + E key combination to go to Computer in Windows Explorer).

Driver Installation (Windows 8.1)

1. Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive.

2. Click/tap the message “Tap to choose what happens with this disc.”

3. Click/tap Run autorun.exe.

4. Click/tap Install Drivers (button), or Option Drivers (button) to access the Optional driver menu.

5. Check the driver installatio n order from T able 4 - 1, on page 4 - 4 (the drivers must be installed in this order)

6. Click/tap to select the driver you wish to install, (you should note down the drivers as you install them).

7. Follow the instructions for each individual driver installation procedure as listed on the appropriate pages.

which is the same as that listed in the Drivers Installer menu below.

Figure 4 - 1 - Autorun Driver Installation Disc

4 - 2 What to Install

Drivers & Utilities

Follow the instructions to install the driver. Alternatively click/tap Start, navigate (Browse.) to the executable file and then follow the manual setup instructions. Note: If you need to reinstall any driver, you sh ould uninstall the driver first.

Figure 4 - 2 - Drivers Installer Screens

See Figure 4 - 3 on page 4 - 9 for the optional driver installer screen.

What to Install 4 - 3

Drivers & Utilities

Windows 8.1 Driver Page # Windows 8.1 Driver - Optional Page #

Chipset Page 4 - 7 PC Camera Module (No driver required) Page 7 - 2 Video Page 4 - 7 Wireless LAN Module Page 7 - 11

LAN Page 4 - 7 Bluetooth & WLAN Combo Module Page 7 - 16 Card Reader Page 4 - 7 Trusted Platform (Security) Module Page 7 - 21 System Brightness AP Page 4 - 7 Wireless Display (No driver required) Page 7 - 35 Airplane Page 4 - 7

MEI Driver Page 4 - 7 Audio Page 4 - 8

Table 4 - 1 - Driver Installation

Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules.

4 - 4 What to Install

Clevo A110SU, A110SU-T User guide

Specifications and Main Features

Frequently Asked Questions

User Manual

Preface

Ergonomics

Chapter 1: Quick Start Guide - Windows 8.1

Overview

Advanced Users

Beginners and Not-So-Advanced Users

Warning Boxes

Not Included

System Software

System Startup

System Map: Front View - Model A

System Map: Front View - Model B

Tilting the LCD Screen

Buttons & LED Indicators

System Map: Left View

HDMI-In Port

Mode Toggle

Menu Button

HDMI-In Port in Sleep or Hibernate Modes

System Map: Right View

System Map: Rear View

Wireless Keyboard & Mouse USB Transceiver

Windows Touch Screen Controls/Gestures

Touch Keyboard

Keyboard Shortcuts - Windows 8.1

Windows 8.1 Control Panel

Windows 8.1 Start Screen & Desktop

The Charms Bar

Windows 8.1 Control Panel

Windows 8.1 Taskbar

Video Features

Power Options

Running Apps

Chapter 2: Features & Components

Overview

Hard Disk Drive

Optical (CD/DVD) Device

Loading Discs

Handling CDs or DVDs

DVD Regional Codes

Multi-in-1 Card Reader

ExpressCard Slot

Audio Features

Setup for Audio Recording

Chapter 3: Power Management

Overview

The Power Sources

AC/DC Adapter

Battery

Turning On the Computer

Shutting the Computer Down

Power Plans

Power-Saving States

Sleep

Hibernate

Shut down

Configuring the Power Buttons

Resuming Operation

Battery Information

Conserving Battery Power

Battery Life

New Battery

Recharging the Battery with the AC/DC Adapter

Proper handling of the Battery Pack

Battery FAQ

Chapter 4: Drivers & Utilities

What to Install

Driver Installation (Windows 8.1)