CleverMic Uno
USB3.0 HD Video Camera
User Manual
Version V1.1（English）
Contents
SAFETY GUIDES....................................................................................................................................................................1
ACCESSORIES .......................................................................................................................................................... .............2
QUICK START ....................................................................................................................................................................... 2
PRODUCT HIGHLIGHTS .................................................................................................................................................... 3
CAMERA SPEC ..................................................................................................................................................................... 3
CAMERA INTERFACE ......................................................................................................................................................... 3
CAMERA DIMENSION ......................................................................................................................................................... 4
IR REMOTE CONTROLLER ............................................................................................................................................... 5
VISCA IN（RS232）PORT.................................................................................................................................................... 7
VISCA PROTOCOL ............................................................................................................................................................... 8
PELCO-D PROTOCOL ....................................................................................................................................................... 14
PELCO-P PROTOCOL ........................................................................................................................................................ 15
OSD MENU........................................................................................................................................................................... 16
IR TRANSFER(IR PASS) ..................................................................................................................................................... 18
UVC CONTROL................................................................................................................................................................... 19
1
SAFETY GUIDES
1.Before operation, please fully read and follow all instructions in the manual. For your
safety, always keep this manual with the camera.
2.The camera power input range is 100-240VAC(50-60Hz),ensure the power supply input
within this rate before powering on.
3.The camera power voltage is 12VDC, rated currency is 2A. We suggest you use it with the
original power supply adapter supplied by the factory.
4.Please keep the power cable, video cable and control cable in a safe place. Protect all
cables especially the connectors.
5.Operational environment: 0℃-50℃, humidity less than 90%.To avoid any danger, do not
put anything inside the camera, and keep away from the corrosive liquid.
6.Avoid stress, vibration and damp during transportation, storage and installation.
7.Do not detetch the camera housing and cover. For any service, please contact authorized
technicians.
8.RF cable and control cable should be individually shielded, and cannot be substituted with
other cables. Do not direct the camera lens towards strong light, such as the sun or the
intensive light.
9.Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent
when there is need to clean. To avoid damage on the camera lens, never use strong or
abrasive cleaning agents on the camera housing.
10.Do not move the camera by holding the camera head. To avoid mechanical trouble, do
not rotate the camera head by hand.
11.Put the camera on fixed and smooth desk or platform, avoid leaned installation.
12. Power Supply Polarity(Drawing)
Note: the video quality may be affected by the specific frequencies of electromagnetic filed.
2
ACCESSORIES
Check all bellow items when open the package:
Camera ··············································· 1
Power Adapter ······································ 1
Power Cable ········································· 1
RS232 Control Cable ······························· 1
USB3.0 Cable ······································· 1
Remote Controller ·································· 1
User Manual ········································· 1
Double-sided Adhesive ···························· 1
QUICK START
1.Check all cable connections before power on.
2.Dial Switch Setting (at the bottom of the camera):
Dial Switch（ARM）
SW-1 SW-2 Instruction
1 OFF OFF Updating mode
2 ON OFF Debugging mode
3 OFF ON Undefined
4 ON ON Working mode
Dial Switch（USB）
SW-5 SW-6 Instruction
1 OFF OFF Undefined
2 ON OFF Working mode
3 OFF ON Updating mode
4 ON ON Undefined
Dial Switch（IR CODE TYPE）
SW-3 SW-4 Instruction
1 OFF OFF Off(Close IR receiver)
2 ON OFF Undefined
3 OFF ON SEJIN 4PPM CODE
4 ON ON NEC CODE(standard)
3
PRODUCT HIGHLIGHTS
1. Fashionable and smart design, with advanced Ambarella A9 DSP, provides ultra crystal image quality.
2. DVI-I(HDMI) &USB3.0 simultaneously output.
3. Fast switching between different video format: only 3 seconds needed.
4. USB2.0 compatible.
5.Daisy chain function: with both Visca in and Visca out port.
6. Multi language menu: English, Chinese, Russian, Spanish.
7.IR transfer/IR pass function: except receiving the camera remote controller signal, the camera can also receive
other codec’s IR remote control signal, and pass these IR control signal to the codec’s IR receiver (via VISCA
IN port).
CAMERA SPEC
1. Video Format: 1080p59.94/50/29.97/25; 720p59.94/50/29.97/25; 1080i59.94/50.
2. Video Output: DVI-I( HDMI), USB3.0
3. Sensor：1/2.8 inch 12MP HD CMOS sensor
4. Lens：f3.9～46.1mm(12Xzoom)，F1.8 – 2.8
5. Angle of View: 72.5°
5.Rotation Angle: Pan rotation:±170°; Tilt rotation: -30°~+90°, support up-side down installation
6. Rotation Speed: Pan speed:0.1°-150°/s; Tile speed: 0.1°-80°/s
7.Preset: 10 via IR remote setting, (255 via COM setting）, preset accuracy :0.2°
8. Support Auto/Manual White Balance, Auto/Manual Exposure (Iris, Shutter), Auto/ Manual/ OnePush Focus.
9. Support WDR function.
10. Control signal port: 8 pin mini DIN--RS232, VISCA/Pelco-D/Pelco-P protocol
11. Power voltage: DC12V/2.0A; power port: HEC3800.
12.Max consumption:24W
13. Working temperature: -5 ~ 45℃
14. Storage temperature:-20 ~ 60℃
15. Net weight: 1.25KG（2.8LBS）
CAMERA INTERFACE
1. Camera Lens 5.Dial Switch 9.VISCA OUT port
2. Camera Base 6. Tripod Screw Hole 10.USB3.0 port
3. Power Indicator Light 7. Installation Hole 11.DVI-I port
4. IR Receiver Panel 8.VISCA IN port 12. Power Input 12VDC
4
CAMERA DIMENSION(mm)
5
IR REMOTE CONTROLLER
POWER
Under normal working mode, short press POWER key, the camera will enter stand by
mode;
Press it again, the camera will do self-configuration, then go back to
HOME position.
It will go to preset position if power on model has been set before.
FREEZE
Short press FREEZE key to freeze/ unfreeze the image.( not work for USB3.0
camera)
IRT(IR Transfer/IR Pass)
Open or close the IR pass function. Once press the IRT key, the camera will receive and
pass the IR remote control signal to the codec/terminal(via VISCA IN port).
SET 1~SET4 ADDRESS SETTING
Long press for 3seconds until the key light ON, to set camera address.
CAM1~CAM4（CAMERA SELECTING）
Short press to select the relative camera.
NUMBER KEY(1-9)
Set preset: long press(3 seconds) the number key to set preset.
Run preset: Short press the number key to run preset.
CLR PRE(CLEAR PRESET)
CLR PRE+ number key: to clear the relative preset.
Long press to clear all preset.
LEARN
Reserved, not available now.
6
FOCUS KEY( ON THE LEFT)
Manual focus, only valid under manual focus model.
ZOOM KEY( ON THE RIGHT SIDE)
Set the zoom rate
NAVIGATE KEY: UP/DOWN/LEFT/RIGHT
Under working mode, use navigate key to set the pan tilt, and select menu when enter OSD.
OK /HOME KEY
Under working mode, short press OK to make the camera go back to HOME position; and
confirm the selection when enter OSD.
AF: Auto Focus
MF: Manual Focus
RESET: Reset camera
MENU: Enter OSD menu
LIMIT L: Set the pan tilt left limit position.
LIMIT R: Set the pan tilt right limit position.
LMT CLR: Clear the limit position.
BLC OFF/ BLC ON：Close/open back light compensation
BRIGHT-/BRIGHT+: Set image brightness, only valid under bright priority exposure mode.
Video Format Keys:
Long press 3 seconds to select different video format output.
7
VISCA IN(RS232) PORT
Construction： VISCA Network
No. Function
1 DTR
2 DSR
3 TXD
4 GND
5 RXD
6 A
7 IR OUT
8 B
VISCA IN & RS485 Connection
Camera VISCA IN
RS485
1
DTR
2
DSR
3
TXD
4
GND
GND
5
RXD
6 A(+)
A(+) 7 IR OUT
8 B(-)
B(-)
VISCA IN & DB9 Connec
tion Camera VISCA IN
Windows DB
-9 1
DTR
6 DSR 2 DSR
4 DTR 3 TXD
2 RXD
4
GND
5 GND
5
RXD
3 TXD
6
A(+)
7 IR OUT
8 B(-)
VISCA IN & Mini DIN Connection
Camera VISCA IN
Mini DIN
1
DTR
1 DSR 2 DSR
2 DTR 3 TXD
5 RXD
4
GND
4 GND
5
RXD
3 TXD
6
A(+)
6 GND
7
IR OUT
7 NC 8 B(-)
8 NC
8
SERIAL PORT CONFIGURATION
Parameter Value Parameter Value
Baud rate 2400/4800/9600/115200 Stop Bit 1bit
Start Bit 1 bit Check Bit None
Date Bit 8 bit
VISCA PROTOCOL
Part1 Camera Return Command
Ack/Completion Message
Command Packet Note
ACK z0 41 FF Returned when the command is accepted.
Completion z0 51 FF Returned when the command has been executed.
z = camera adderss+8
Error Messages
Command Packet Note
Syntax Error z0 60 02 FF
Returned when the command format is different or when a command
with illegal command parameters is accepted.
Command Not Executable z0 61 41 FF
Returned when a command cannot be executed due to current conditions.
For example, when commands controlling the focus manually are
received during auto focus.
Part 2 Camera Control Command
Command Function Command Packet Note
AddressSet Broadcast 88 30 01 FF Address setting
IF_Clear Broadcast 88 01 00 01 FF I/F Clear
CommandCancel 8x 21 FF
CAM_Power
On 8x 01 04 00 02 FF
Power ON/OFF
Off 8x 01 04 00 03 FF
CAM_Zoom
Stop 8x 01 04 07 00 FF
Tele(Standard) 8x 01 04 07 02 FF
Wide(Standard) 8x 01 04 07 03 FF
Tele(Variable) 8x 01 04 07 2p FF
p = 0(low)~7(high)
Wide(Variable) 8x 01 04 07 3p FF
Direct 8x 01 04 47 0p 0q 0r 0s FF pqrs: Zoom Position (0(wide) ~0x4000(tele))
CAM_Focus
Stop 8x 01 04 08 00 FF
Far(Standard) 8x 01 04 08 02 FF
Near(Standard) 8x 01 04 08 03 FF
Direct 8x 01 04 48 0p 0q 0r 0s FF pqrs: Focus Position
One Push AF 8x 01 04 18 01 FF
CAM_ZoomFocus Direct
8x 01 04 47 0p 0q 0r 0s
0t 0u 0v 0w FF
pqrs: Zoom Position (0(wide)~ 0x4000(tele))
tuvw: Focus Position
CAM_WB
Auto 8x 01 04 35 00 FF
Indoor 8x 01 04 35 01 FF
Outdoor 8x 01 04 35 02 FF
OnePush 8x 01 04 35 03 FF
9
Command Function Command Packet Note
Manual 8x 01 04 35 05 FF
Outdoor Auto 8x 01 04 35 06 FF
Sodium Lamp Auto 8x 01 04 35 07 FF
Sodium Auto 8x 01 04 35 08 FF
CAM_RGain
Reset 8x 01 04 03 00 FF
Manual Control of R Gain Up 8x 01 04 03 02 FF
Down 8x 01 04 03 03 FF
Direct 8x 01 04 43 00 00 0p 0q FF pq: R Gain (0~0xFF)
CAM_Bgain
Reset 8x 01 04 04 00 FF
Manual Control of B Gain Up 8x 01 04 04 02 FF
Down 8x 01 04 04 03 FF
Direct 8x 01 04 44 00 00 0p 0q FF pq: B Gain (0-0xFF)
CAM_AE
Full Auto 8x 01 04 39 00 FF Automatic Exposure mode
Manual 8x 01 04 39 03 FF Manual Control mode
Bright 8x 01 04 39 0D FF Bright mode(Manual control)
CAM_Shutter
Reset 8x 01 04 0A 00 FF
Shutter Setting Up 8x 01 04 0A 02 FF
Down 8x 01 04 0A 03 FF
Direct 8x 01 04 4A 00 00 0p 0q FF pq: Shutter Position (0~0x15)
CAM_Iris
Reset 8x 01 04 0B 00 FF
Iris Setting Up 8x 01 04 0B 02 FF
Down 8x 01 04 0B 03 FF
Direct 8x 01 04 4B 00 00 0p 0q FF pq: Iris Position (0~ 0x11)
CAM_Gain
Reset 8x 01 04 0C 00 FF
Gain Setting Up 8x 01 04 0C 02 FF
Down 8x 01 04 0C 03 FF
Direct 8x 01 04 0C 00 00 0p 0q FF pq: Gain Positon (0~0x0E)
CAM_Bright
Reset 8x 01 04 0D 00 FF
Bright Setting Up 8x 01 04 0D 02 FF
Down 8x 01 04 0D 03 FF
Direct 8x 01 04 4D 00 00 0p 0q FF pq: Bright l Positon ()
CAM_ExpComp
On 8x 01 04 3E 02 FF
Exposure Compensation ON/OFF
Off 8x 01 04 3E 03 FF
Reset 8x 01 04 0E 00 FF
Exposure Compensation Amount Setting Up 8x 01 04 0E 02 FF
Down 8x 01 04 0E 03 FF
Direct 8x 01 04 4E 00 00 0p 0q FF pq: ExpComp Position (0~0x0E)
CAM_BackLight
On 8x 01 04 33 02 FF BackLight On
Off 8x 01 04 33 03 FF BackLight Off
CAM_Aperture
Reset 8x 01 04 02 00 FF
Aperture Control Up 8x 01 04 02 02 FF
Down 8x 01 04 02 03 FF
Direct 8x 01 04 42 00 00 0p 0q FF pq: Aperture Gain (0~0x04)
CAM_Memory
Reset 8x 01 04 3F 00 0p FF
p: Memory Number(=0 to 127)
Corresponds to 0 to 9 on the Remote Commander
Set 8x 01 04 3F 01 0p FF
Recall 8x 01 04 3F 02 0p FF
CAM_LR_Reverse
On 8x 01 04 61 02 FF
Image Flip Horizontal ON/OFF
Off 8x 01 04 61 03 FF
CAM_PictureFlip
On 8x 01 04 66 02 FF
Image Flip Vertical ON/OFF
Off 8x 01 04 66 03 FF
10
Command Function Command Packet Note
CAM_MountMode
UP 8x 01 04 A4 02 FF Mount Up
Down 8x 01 04 A4 03 FF Mount Down
CAM_ColorGain Direct 8x 01 04 49 00 00 00 0p FF (0~0x0E)
CAM_2D
Noise Reduction
Direct 8x 01 04 53 0p FF (0~0x05)
CAM_3D
Noise Reduction
Direct
8x 01 04 54 0p FF
(0~0x03)
FLICK
50HZ 81 01 04 23 01 FF
60HZ 81 01 04 23 02 FF
Freeze
Freeze On 81 01 04 62 02 FF Freeze On Immediately
Freeze Off 81 01 04 62 03 FF Freeze Off Immediately
Preset Freeze On 81 01 04 62 22 FF Freeze On When Running Preset
Preset Freeze Off 81 01 04 62 23 FF Freeze Off When Running Preset
VideoSystem Set 8x 01 06 35 00 pp FF
pp: 0~18 Video format
0:1080P60
1:1080P50
2:1080I60
3:1080I50
4:1080P30
5:1080P25
6:720P60
7:720P50
8:720P30
9:720P25
10:1600*900@60(USB OUTPUT)
11:1440*900@60HZ(USB OUTPUT)
12:1366*768@60HZ(USB OUTPUT)
13:1280*800@60HZ(USB OUTPUT)
14:1024*768@60HZ(USB OUTPUT)
15:800*600@60HZ(USB OUTPUT)
16:800*600@30HZ(USB OUTPUT)
17:640*480@60HZ(USB OUTPUT)
18:640*480@30HZ(USB OUTPUT)
CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs: Camera ID (=0000 to FFFF)
SYS_Menu
Menu On 8x 01 06 06 02 FF Turn on the menu
Menu Off 8x 01 06 06 03 FF Turn off the menu
Menu Back 8x 01 06 06 10 FF Menu step back
Menu Ok 8x 01 7E 01 02 00 01 FF Menu ok
IR_Transfer
Transfer On 8x 01 06 1A 02 FF
Receive IR(remote commander) CODE from
VISCA communication ON/OFF
Transfer Off 8x 01 06 1A 03 FF
IR_Receive
On 8x 01 06 08 02 FF
IR(remote commander)receive ON/OFF Off 8x 01 06 08 03 FF
On/Off 8x 01 06 08 10 FF
IR_ReceiveReturn
On 8x 01 7D 01 03 00 00 FF
IR(remote commander)receive message via the
VISCA communication ON/OFF
Off 8x 01 7D 01 13 00 00 FF
Pan_tiltDrive
Up 8x 01 06 01 VV WW 03 01 FF
VV: Pan speed 0x01 (low speed) to 0x18 (high
speed)
WW: Tilt speed 0x01 (low speed) to 0x14 (high
speed)
YYYY: Pan Position(TBD)
ZZZZ: Tilt Position(TBD)
Down 8x 01 06 01 VV WW 03 02 FF
Left 8x 01 06 01 VV WW 01 03 FF
Right 8x 01 06 01 VV WW 02 03 FF
Upleft 8x 01 06 01 VV WW 01 01 FF
Upright 8x 01 06 01 VV WW 02 01 FF
DownLeft 8x 01 06 01 VV WW 01 02 FF
DownRight 8x 01 06 01 VV WW 02 02 FF
Stop 8x 01 06 01 VV WW 03 03 FF
AbsolutePosition
8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
RelativePosition
8x 01 06 03 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
11
Command Function Command Packet Note
Home 8x 01 06 04 FF
Reset 8x 01 06 05 FF
Pan-tiltLimitSet
Set
8x 01 06 07 00 0W
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
W:1 UpRight 0:DownLeft
YYYY: Pan Limit Position(TBD)
ZZZZ: Tilt Limit Position(TBD)
Clear
8x 01 06 07 01 0W
07 0F 0F 0F 07 0F 0F 0F FF
Part 3 Inquiry Command
Command
Command Packet
Return Packet
Note
CAM_PowerInq 8x 09 04 00 FF
y0 50 02 FF
On
y0 50 03 FF
Off(Standby)
CAM_ZoomPosInq
8x 09 04 47 FF
y0 50 0p 0q 0r 0s FF
pqrs: Zoom Position
CAM_FocusModeInq 8x 09 04 38 FF
y0 50 0
2 FF Auto Focus
y0 50 03 FF
Manual Focus
CAM_FocusPosInq
8x 09 04 48 FF
y0 50 0p 0q 0r 0s FF
pqrs: Focus Position
CAM_WBModeInq 8x 09 04 35 FF
y0 50 00 FF
Auto y0 50 01 FF
Indoor mode
y0 50 02 FF
Outdoor mode
y0 50 03 FF
OnePush mode
y0 50
04 FF
ATW
y0 50 05 FF
Manual
CAM_RGainInq
8x 09 04 43 FF
y0 50 00 00 0p 0q FF
pq: R Gain
CAM_BGainInq
8x 09 04 44 FF
y0 50 00 00 0p 0q FF
pq: B Gain
CAM_AEModeInq 8x 09 04 39 FF
y0 50 00 FF
Full Auto
y0 50 03 FF
Manual
y0 50 0A FF
Shutter prio
rity y0 50 0B FF
Iris priority
y0 50 0D FF
Bright
CAM_ShutterPosInq
8x 09 04 4A FF
y0 50 00 00 0p 0q FF
pq: Shutter Position
CAM_IrisPosInq
8x 09 04 4B FF
y0 50 00 00 0p 0q FF
pq: Iris Position
CAM_GainPosiInq
8x 09 04 4C FF
y0 50 00 00 0p 0q
FF
pq: Gain Position
CAM_ BrightPosiInq
8x 09 04 4D FF
y0 50 00 00 0p 0q FF
pq: Bright Position
CAM_ExpCompModeIn
q
8x 09 04 3E FF
y0 50 02 FF
On
y0 50 03 FF
Off CAM_ExpCompPosInq
8x 09 04 4E FF
y0 50 00 00 0p 0q FF
pq: ExpComp Position
CAM_Apertur
eInq 8x 09 04 42 FF
y0 50 00 00 0p 0q FF
pq: Aperture Gain
CAM_MemoryInq
8x 09 04 3F FF
y0 50pp FF
pp: Memory number last operated.
SYS_MenuModeInq
8x 09 06 06 FF
y0 50 02 FF
On
y0 50 03 FF
Off CAM_LR_ReverseInq
8x 09 04 61 FF
y0 50 02 FF
On
y0 50
03 FF
Off CAM_PictureFlipInq
8x 09 04 66 FF
y0 50 02 FF
On
y0 50 03 FF
Off CAM_IDInq
8x 09 04 22 FF
y0 50 0p 0q 0r 0s FF
pqrs: Camera ID
CAM_VersionInq 8x 09 00 02 FF
y0 50 ab cd
mn pq rs tu vw FF
VideoSystemInq 8x 09 06 23 FF y0 50 pp FF
pp: 0~
18 Video format
0:1080P60
1:1080P50
2:1080I60
3:1080I50
4:1080P30
5:1080P25
6:720P60
7:720P50
8:720P30
9:720P25
10:1600*900@60(USB OUTPUT)
12
11:1440*900@60HZ(USB OUTPUT)
12:1366*768@60HZ(USB OUTPUT)
13:1280*800@60HZ(USB OUTPUT)
14:1024*768@60HZ(USB OUTPUT)
15:800*600@60HZ(USB OUTPUT)
16:800*600@30HZ(USB OUTPUT)
17:640*480@60HZ(USB OUTPUT)
18:640*480@30HZ(USB OUTPUT)
IR_Transfer 8x 09 06 1A FF
y0 50 02 FF
On
y0 50 03 FF
Off
IR_Receive 8x 09 06 08 FF
y0 50 02 FF
On
y0 50 03 FF
Off
IR_ReceiveReturn
y0 07 7D 01 04 00 FF
Power ON/OFF
y0 07 7D 01 04 07 FF
Zoom tele/wide
y0 07 7D 01 04 38 FF
AF On/Off
y0 07 7D 01 04 33 FF
CAM_Backlight
y0 07 7D 01 04 3F FF
CAM_Memory
y0 07 7D 01 06 01 FF
Pan_tiltDrive
Pan-tiltMaxSpeedInq 8x 09 06 11 FF y0 50 ww zz FF
ww: Pan Max Speed
zz: Tilt Max Speed
Pan-tiltPosInq 8x 09 06 12 FF
y0 50 0w 0w 0w 0w
0z 0z 0z 0z FF
wwww: Pan Position
zzzz: Tilt Position
Note:【x】 means the camera address ;【y】=【x + 8】.
VISCA Pan Tilt Absolute Position Value
Pan Angle
VISCA Value
Tilt Angle
VISCA Value
-170 0xF670
-30 0xFE50
-135 0xF868
0
0x0000
-90 0xFAF0
30
0x01B0
-45 0xFD78
60
0x0360
0
0x0000
90
0x510
45
0x0288
90 0x0510
135 0x0798
170 0x0990
VISCA PanTilt Speed Value
Pan(degree/second)
tilt(degree/second)
0
0.3 0 0.3 1 1 1 1 2 1.5 2 1.5 3 2.2 3 2.2 4 2.4 4 3.6 5 2.6 5 4.7 6 2.8 6 6 7 3.0 7 8 8 3.2 8 10 9 3.4 9 12 10 3.8 10 15 11 4.5 11 18 12 6 12 23 13 9 13 30 14 15 14 39 15 19 15 48 16 25 16 59 17 32 17 69 18 38 18 80 19 45 20 58
13
21 75 22 88 23 105 24 120
VISCA Exposure Value
Shutter speed
21
1/10000
Iris
0
close
20
1/6000
1
f32
19
1/4000
2
f28
18
1/3000
3
f24
17
1/2000
4
f22
16
1/1500
5
f18
15
1/1000
6
f14
14
1/725
7
f11
13
1/500
8
f9.6
12
1/350
9
f6.8
11
1/250
10
f5.6
10
1/180
11
f4.8
9
1/125
12
f4.0
8
1/100
13
f3.4
7
1/90
14
f2.8
6
1/60
15
f2.4
5
1/30
16
f2.0
4
1/15
17
f1.8
3
1/8
2
/
1
/
0
/
Gain
0
0dB
Gain
8
16dB
1
2dB
9
18dB
2
4dB
10
20dB
3
6dB
11
22dB
4
8dB
12
24dB
5
10dB
13
26dB
6
12dB
14
28dB
7
14dB
Zoom Rate & Zoom Value
Zoom Rate
Value
x1(wide)
0x0
x1.2
0x8D0
x1.5
0x1194
x2
0x1A58
x3
0x2610
x5
0x31D4
14
x5.8
0x34BC
x6.9
0x37A4
x8.2
0x3A98
x9.9
0x3D8C
x11.8(tele)
0x4000
15
PELCO-D PROTOCOL
Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7
Up 0xFF Address 0x00 0x08 Pan Speed Tilt Speed SUM
Down 0xFF Address 0x00 0x10 Pan Speed Tilt Speed SUM
Left 0xFF Address 0x00 0x04 Pan Speed Tilt Speed SUM
Right 0xFF Address 0x00 0x02 Pan Speed Tilt Speed SUM
Upleft 0xFF Address 0x00 0x0C Pan Speed Tilt Speed SUM
Upright 0xFF Address 0x00 0x0A Pan Speed Tilt Speed SUM
DownLeft 0xFF Address 0x00 0x14 Pan Speed Tilt Speed SUM
DownRight 0xFF Address 0x00 0x12 Pan Speed Tilt Speed SUM
Zoom In 0xFF Address 0x00 0x20 0x00 0x00 SUM
Zoom Out 0xFF Address 0x00 0x40 0x00 0x00 SUM
Focus Far 0xFF Address 0x00 0x80 0x00 0x00 SUM
Focus Near 0xFF Address 0x01 0x00 0x00 0x00 SUM
Set Preset 0xFF Address 0x00 0x03 0x00 Preset ID SUM
Clear Preset 0xFF Address 0x00 0x05 0x00 Preset ID SUM
Call Preset 0xFF Address 0x00 0x07 0x00 Preset ID SUM
Query Pan Position 0xFF Address 0x00 0x51 0x00 0x00 SUM
Query Pan Position Response 0xFF Address 0x00 0x59
Value High
Byte
Value Low
Byte
SUM
Query Tilt Position 0xFF Address 0x00 0x53 0x00 0x00 SUM
Query Tilt Position Response 0xFF Address 0x00 0x5B
Value High
Byte
Value Low
Byte
SUM
Query Zoom Position 0xFF Address 0x00 0x55 0x00 0x00 SUM
Query Zoom Position
Response
0xFF Address 0x00 0x5D
Value High
Byte
Value Low
Byte
SUM
16
PELCO-P PROTOCOL
Function Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Byte8
Up 0xA0 Address 0x00 0x08 Pan Speed Tilt Speed 0xAF XOR
Down 0xA0 Address 0x00 0x10 Pan Speed Tilt Speed 0xAF XOR
Left 0xA0 Address 0x00 0x04 Pan Speed Tilt Speed 0xAF XOR
Right 0xA0 Address 0x00 0x02 Pan Speed Tilt Speed 0xAF XOR
Upleft 0xA0 Address 0x00 0x0C Pan Speed Tilt Speed 0xAF XOR
Upright 0xA0 Address 0x00 0x0A Pan Speed Tilt Speed 0xAF XOR
DownLeft 0xA0 Address 0x00 0x14 Pan Speed Tilt Speed 0xAF XOR
DownRight 0xA0 Address 0x00 0x12 Pan Speed Tilt Speed 0xAF XOR
Zoom In 0xA0 Address 0x00 0x20 0x00 0x00 0xAF XOR
Zoom Out 0xA0 Address 0x00 0x40 0x00 0x00 0xAF XOR
Focus Far 0xA0 Address 0x00 0x80 0x00 0x00 0xAF XOR
Focus Near 0xA0 Address 0x01 0x00 0x00 0x00 0xAF XOR
Set Preset 0xA0 Address 0x00 0x03 0x00 Preset ID 0xAF XOR
Clear Preset 0xA0 Address 0x00 0x05 0x00 Preset ID 0xAF XOR
Call Preset 0xA0 Address 0x00 0x07 0x00 Preset ID 0xAF XOR
Query Pan Position 0xA0 Address 0x00 0x51 0x00 0x00 0xAF XOR
Query Pan Position
Response
0xA0 Address 0x00 0x59
Value High
Byte
Value Low
Byte
0xAF XOR
Query Tilt Position 0xA0 Address 0x00 0x53 0x00 0x00 0xAF XOR
Query Tilt Position
Response
0xA0 Address 0x00 0x5B
Value High
Byte
Value Low
Byte
0xAF XOR
Query Zoom Position 0xA0 Address 0x00 0x55 0x00 0x00 0xAF XOR
Query Zoom Position
Response
0xA0 Address 0x00 0x5D
Value High
Byte
Value Low
Byte
0xAF XOR
17
OSD MENU
1.Under working mode, press the MENU key on the IR remote controller, to enter the OSD menu as bellow shows:
2.After enter the main menu, use the navigate key to select the main menu. Once been selected, the main
menu will change to blue background, and the right side will show all sub menu options .
3.Press the navigate key to enter sub menu; use key to select the sub menu;use key to
select parameter.
4. Press the MENU key again to return to previous menu. Press the MENU key continuously to exit the OSD menu.
Before exiting, will show up a window to select whether need to save all settings(use key to set). As bellow:
5.OSD Menu Setting List
SYSTEM
PROTOCOL VISCA,PELCO-P,PELCO-D
ADDRESS VISCA:1~7 PELCO-P/D:1~255
BAUD RATE 2400,4800,9600,115200
PTL LOCK Protocol lock: once set, above protocol setting will be locked, to avoid changes
RS485 RS485 ON/OFF ( RS485 function is customized)
VGA OUT VGA output can be YPbPr or VGA output (customized)
TRANSFER IR Transfer/IR Pass function
LANGUAGE Chinese, English, Spanish, Russian
EXPOSURE
EXPOSURE MODE AUTO、MANUAL、BRIGHT
SHUTTER Shutter speed:1/8~1/10000, only valid under manual mode
IRIS Iris setting:CLOSE~F1.8, only valid under manual mode
GAIN Gain setting:0dB~28dB , only valid under manual mode
BRIGHT Bright setting:0~15, only valid under bright priority mode.
BLC Back light compensation ON/FF
BLC LEVEL Set back light compensation level
18
IMAGE
WB MODE
White Balance:AUTO、INDOOR、OUTDOOR、MANUAL、OUTAUTO、
SODIUM LAMP AUTO 、SODIUM LAMP
R GAIN Red gain level: 0~255, only valid under manual white balance mode.
B GAIN Blue gain level:0~255 , only valid under manual white balance mode.
COLOR G Color gain setting: 0~14
FLICK Anti-Flicker setting:50/60HZ, to reduce the video flicker
QUALITY
2D NR
2D noise reduction:0~5, the bigger value, the less noise on image, the lower
resolution
3D NR 3D noise reduction:0~3, the bigger value, the less motion noise on image.
SHARPNESS Sharpness setting: 0~4, the higher value, the higher resolution.
PTZ
PWR ACT Set power on action: OFF, PRE1, PRE2
SPEEDBYZ Speed by zoom: proportional speed, the bigger zoom, the slower speed.
MOUNT M Mount mode: up, down
FLIP.HOR Flip horizontal
FLIP VER Flip vertical
PT SPD Set pan tilt speed
ZOOM SPD Set zoom speed
FREEZE Video freeze function, currently USB3.0 camera doesn’t support.
VIDEO
FORMAT
1080P59.94 720P29.97 800*600@30(USB)
Once selected, press OK
key to confirm.
1080P50 720P25 640*480@60(USB)
1080I59.94 1600*900@60(USB) 640*480@30(USB)
1080I50 1400*900@60(USB)
1080P29.97 1366*768@60(USB)
1080P25 1280*800@60(USB)
720P59.94 1024*768@60(USB)
720P50 800*600@60(USB)
RESET
SYS RESET System reset
CAM RESET Camera reset
PT RESET Pan tilt reset
ALL RESET All reset
MESSAGE
IR ADDR Camera IR control address
FOCUS Focus mode
CLIENT Client protocol, can’t be changed
MODEL NO. Model number
ARM VER ARM version
FPGA VER FPGA version
CAM VER Camera version
RELEASE Software release date
19
IR TRANSFER(IR PASS)
1 IR transfer( IR Pass) function available by setting the SW3 and SW4( at the bottom of the camera). Currently the camera
support NEC and SEJIN 4PPM code. For customized with other code, pls contact us for adding:
2. Once the camera power on and finish configuration:
if set to NEC code, can enable the IR transfer function via OSD menu or via serial command.
if set non NEC code, then can enable it only via VISCA IN port.
3. Put the targeted remote controller towards to the camera IR receiver, press keys on the remote controller, then the
camera will output the received IR code via VISCA IN port.
4. IR Transfer output format:
XX XX XX XX FF
6. The camera can save all settingS, no need to re-set after power off and on.
Dial Switch（IR CODE TYPE）
SW-3 SW-4 Note
1 OFF OFF
Off（Close IR Transfer）
2 ON OFF Undefined
3 OFF ON SEJIN 4PPM CODE
4 ON ON NEC CODE(standard)
XX XX XX XX: Remote Controller Code
FF: End Code
20
UVC CONTROL
1. Only run the client software after the USB3.0 HD camera has completed self-configuration(the IR indicator in blue
color and will not flash); If run the software before the camera configuration finishes, may cause black video issue.
2. Make sure the USB3.0 camera is recognized by the PC Device Manager. In case the PC does not recognize the
camera(with warning of “MFG”), following bellow steps:
1).Go to Device Manager.
2).Right click on the device(yellow warning with "MFG ") and select "Update Driver Software".
3).Next select "Browse my computer for Driver Software" and then select "Let me pick from a list of device drivers on My computer".
4).Next select "USB Composite Driver" and continue install the driver up to over.
5).Then it should come up as "USB3.0 HD CAMERA".
3. Make sure the interval of different video format switching more than 3 seconds, otherwise black video maybe caused.
4. Make sure the interval of control command sending from the server(via USB cable) to the camera no less than 250ms.
5. Support standard UVC interface.
UVC Property Corresponded VISCA Command
PU_BACKLIGHT_COMPENSATION_CONTROL
8x 01 04 33 02 FF
PU_BRIGHTNESS_CONTROL
8x 01 04 4D 00 00 0p 0q FF
PU_GAIN_CONTROL
8x 01 04 49 00 00 00 0p FF
PU_SHARPNESS_CONTROL
8x 01 04 42 00 00 0p 0q FF
PU_WHITE_BALANCE_TEMPERATURE_CONTROL
8x 01 04 35 0p FF
CT_ZOOM_ABSOLUTE_CONTROL
8x 01 04 47 0p 0q 0r 0s FF
CT_PANTILT_ABSOLUTE_CONTROL
8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z F
PU_CONTRAST_CONTROL
8x 01 04 53 0p FF
PU_HUE_CONTROL
8x 01 04 54 0p FF
6. Note: different to standard UVC protocol, PU_CONTRAST_CONTROL means 2D noise reduction, not CONTRAST
value; PU_HUE_CONTROL means 3D noise reduction, not HUE（chroma）value.
Loading...