Cleveland Range OGB-6.20, OGB-10.10, OGS-6.20, OGS-10.10 User Manual

Service & Parts Manual

by

Convotherm Combination Oven-Steamer

MODELS:

OGS-10.10

Gas 10.10 and 6.20

OGS-6.20

Enodis

OGB-10.10

OGB-6.20

1333 East 179th St., Cleveland, Ohio, U.S.A. 441

Phone: (216) 481-4900 Fax: (216) 481-3782 Visit our web site at www.clevelandrange.com

10

0706

Post instructions to be followed if the user smells gas. Display the instructions in a prominent location. All users of this equipment must understand the instructions. Obtain the instructions from the local gas supplier. Failure to follow the instructions if there is a gas leak can cause death, injury, and/or property damage.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment.

NOTICE

WARNING

Disconnect power at the main external power switch before servicing or repairing a Combi.

Failure to disconnect power can result in death, injury, and property damage.

ALL SERVICE MUST BE PERFORMED BY A QUALIFIED

CLEVELAND RANGE AUTHORIZED TECHNICIAN.

Do not connect the Combi Oven-Steamer drain connection to any

drain material that cannot sustain 140

Using drain material that cannot withstand 140o Fahrenheit can

result in injury, equipment damage, and property damage.

WARNING

o

Fahrenheit.

This Installation Manual is a part of your new Combi Oven-Steamer. You must keep and maintain it

for the entire life span of your Combi and pass it on to the next owner of the Combi.

KEEP THIS MANUAL FOR REFERENCE

This manual may be subject to new technical developments, modifications, and unforeseen errors.

DO NOT OPERATE OR ATTEMPT TO OPERATE THIS APPLIANCE OR ANY ACCESSORIES WITHOUT READING

COMPLETELY AND FULLY UNDERSTANDING THIS MANUAL

For caster equipped Combis: Per separate instructions, connect the strain relief (restraining

device) and complete any remaining installation procedures BEFORE starting the Combi.

Convotherm by Cleveland Combi Oven-Steamers are intended for other than household use.

Cleveland STATEMENT OF POLICIES

2

L I M I T E D W A R R A N T Y

CLEVELAND RANGE products are warranted to the original purchaser to be free from defects in materials and workmanship under normal use and service for the standard warranty period of one year from date of installation or 18 months from date of shipment, which ever comes first.

CLEVELAND RANGE agrees to repair or replace, at its option, f.o.b. factory, any part which proves to be defective due to defects in material or workmanship during the warranty period, providing the equipment has been unaltered, and has been PROPERLY INSTALLED, MAINTAINED, AND OPERATED IN ACCORDANCE WITH THE CLEVELAND RANGE OWNER’S MANUAL.

CLEVELAND RANGE agrees to pay any FACTORY AUTHORIZED EQUIPMENT SERVICE AGENCY (within the continental United States, and Hawaii) for reasonable labor required to repair or replace, at our option, f.o.b. factory, any part which proves to be defective due to defects in material or workmanship, during the labor warranty period. This warranty includes travel time not to exceed two hours and mileage not to exceed 50 miles (100 miles round-trip), BUT DOES NOT INCLUDE POST START-UP, TIGHTENING LOOSE FITTINGS, MINOR ADJUSTMENTS, MAINTENANCE, CLEANING OR DESCALING.

The standard labor warranty allows factory payment of reasonable labor required to repair or replace such defective parts. Cleveland Range will not reimburse the expense of labor required for the repair or replacement of parts after the standard warranty period, unless an Extended Labor Warranty Contract has been purchased to cover the equipment for the balance of the warranty period from the date of equipment installation, start-up, or demonstration.

PROPER INSTALLATION IS THE RESPONSIBILITY OF THE DEALER, THE OWNER-USER, OR INSTALLING CONTRACTOR, AND IS NOT COVERED BY THIS WARRANTY. Many local codes exist, and it is the responsibility of the owner and installer to comply with these codes. Cleveland Range equipment is built to comply with applicable standards for manufacturers, including UL, ANSI, NSF, ASME/Ntl. Bd., CSA, and others.

BOILER (Steam Generator) MAINTENANCE IS THE RESPONSIBILITY OF THE OWNER-USER AND IS NOT COVERED BY THIS WARRANTY. The use of good quality feed water is the responsibility of the Owner-User (see Water Quality Recommendations below). THE USE OF POOR QUALITY FEED WATER WILL VOID EQUIPMENT WARRANTIES. Boiler maintenance supplies, including boiler hand hole gaskets, are not warranted beyond the first 90 days after the date the equipment is placed into service. Preventive maintenance records must be available showing descaling per applicable Cleveland Operator Manual for Boiler Proration Program considerations.

WATER QUALITY RECOMMENDATIONS

TOTAL DISSOLVED SOLIDS less than 60 parts per million TOTAL ALKALINITY less than 20 parts per million SILICA less than 13 parts per million CHLORIDE less than 30 parts per million pH FACTOR greater than 7.5

The foregoing shall constitute the sole and exclusive remedy of original purchaser and the full liability of Cleveland Range for any breach of warranty. THE FOREGOING IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER WRITTEN, ORAL, OR IMPLIED, INCLUDING ANY WARRANTY OF PERFORMANCE, MERCHANTABILITY, OR FITNESS FOR PURPOSE, AND SUPERSEDES AND EXCLUDES ANY ORAL WARRANTIES OR REPRESENTATIONS, OR WRITTEN WARRANTIES OR REPRESENTATIONS, NOT EXPRESSLY DESIGNATED IN WRITING AS A “WARRANTY” OR “GUARANTEE” OF CLEVELAND RANGE MADE OR IMPLIED IN ANY MANUAL, LITERATURE, ADVERTISING BROCHURE OR OTHER MATERIALS.

CLEVELAND RANGE’S liability on any claim of any kind, including negligence, with respect to the goods or services covered hereunder, shall in no case exceed the price of the goods or services, or part thereof, which gives rise to the claim. IN NO EVENT SHALL CLEVELAND RANGE BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES IN THE NATURE OF PENALTIES.

3

GENERAL INFORMATION ABOUT COMBIS

A. PRODUCT INFORMATION

Cleveland Range, LLC assigns two product identification numbers to each Combi: a model number and a serial number. The model number identifies the product characteristics. The serial number identifies the individual Combi.

1. Model Number

a. This manual covers the installation of the OEB and OES model gas powered Combis. b. Model Number Key: “O” stands for the Combi series Oven, “E” or “G” designates Electric or Gas.

“B” designates Steam Generator, and “S” designates Spritzer. The first number designates the number of shelves in the oven rack. The second number is either “.10” for 12” X 20” steam table pans or “.20” for 18” X 26” full size sheet pans. For further information, contact your Convotherm by Cleveland sales representative or Cleveland Range.

2. Serial Number and Equipment Record

During manufacture, Combis are assigned individual serial numbers. Please provide the following information when you contact Cleveland Range or a qualified Cleveland Range authorized service representative:

Serial Number________________________________________________________________

(Write the Serial Number of your Combi here.)

Model Number________________________________________________________________

(Write the Model Number of your Combi here.)

3. Product Information Plate

The Product Information Plate on the left side of the Combi lists the model, serial number, gas, electric, and wiring requirements of the Combi. Figure 1-1 illustrates a typical Product Information Plate.

Figure 1-1

Typical Product Information Plate

INSTALLATION INSTRUCTIONS

4

A. GENERAL

This equipment should be installed only by qualified, professional plumbers, pipe fitters, and electricians.

1. The installation of this Combi must conform with: a. The National Fuel Gas Code, ANSI Z223.1 / NFPA 54 (latest edition), or the

Natural Gas and Propane Installation Code CSA B1 49.1 as applicable.

b. The National Electrical Code, ANSI/NFPA 70 (latest edition), or the Canadian

Electrical Code, CSA C22.2 as applicable. c. The Food Service Sanitation Manual of the Food and Drug Administration (FDA). d. All applicable national, state, and local laws, codes, and regulations.

2. This equipment is to be installed to comply with the applicable federal, state, or local plumbing codes.

3. Installation instructions must be read in their entirety before starting installation of a Combi.

4. Install the Combi according to the policies and procedures outlined in this manual.

DANGER

Improper installation, adjustment, alteration, service, or maintenance of a Combi, or installation of a damaged Combi can result in DEATH, INJURY, EQUIPMENT DAMAGE, and void the warranty.

NEVER install damaged Combis. ALWAYS have qualified Cleveland Range authorized personnel install and service Combis.

5. Inspect the Combi for shipping damage. a. Check carton and packing for shipping damage. b. Note any damage on the shipping paperwork as soon as the carton arrives. c. Unpack the Combi and check for shipping damage. d. If the Combi is damaged or damage is suspected:

1) Inform your dealer at once.

2) Inform Cleveland Range in writing within 3 days.

3) Submit a Damage Claim to the Shipper.

B. INSTALLATION OF THE COMBI – General Instructions

5

General Instructions:

1. Select the Combi’s operating location.

2. Complete the water, drain, and electric lines before positioning and leveling the Combi.

3. Position and level the Combi.

4. Connect the utility lines after

5. Call Cleveland Range at 216-481-4900 for the Free Start-Up Program’s Performance Checkout.

6. After Setup and Performance Checkout, the Combi should provide years of reliable operation.

positioning and leveling the Combi.

DANGER

Improper lifting can result in DEATH, INJURY, AND EQUIPMENT DAMAGE.

Use enough workers with training and experience lifting heavy equipment to place

Combis on supporting surfaces, and lift and handle Combis and acessories.

Operating an out of level Combi can cause DEATH, INJURY, and EQUIPMENT DAMAGE.

Combis must be level both front-to-back and side-to-side in all installations.

NEVER operate an out of level Combi.

If a Combi is suspected to be out of level, shut it down at once and call you qualified

Cleveland Range authorized service agency at once.

All clearance requirements above, below, and around the Combi are the same for noncombustible locations as for combustible locations. Failure to maintain required clearances and additional distances as needed can result INJURY and EQUIPMENT DAMAGE. Consult manufacturers’ literature, and sales and service agencies as needed.

DANGER

WARNING

C. SPECIAL INSTRUCTIONS FOR CASTER EQUIPPED COMBI STANDS AND COMBIS

6

1. Read all instructions before beginning installation.

2. Level the floor if needed.

3. NOTE: Combis on caster-equipped stands have less adjustment for level than adjustable

foot equipped stands.

4. The front wheels of caster-equipped stands and Combis have locks. Check the caster

locks for function and position before installation.

5. Follow the separate instructions included with the Stand, Stacking Kit, or Caster Kit.

6. Make sure the Stand, Stacking Kit, or Caster Kit matches the Combi(s).

7. Use only genuine Cleveland Range Stands, Stacking Kits, Caster Kits, and replacement

parts.

8. Use of Stands, Stacking Kits, Caster Kits, and replacement parts other than genuine

Cleveland Range Stands, Stacking Kits, and Caster Kits and replacement parts can result in injury and / or catastrophic equipment failure, and voids the Warranty.

9. The appliance must be secured to building structure, to prevent any strain on the utility

connections, and to help reduce the risk of electric shock.

10. The strain relief (restraining device) must be installed to limit the movement of the

appliance without depending on the connector and the quick-disconnect device or its associated piping (gas, water, or electric). See separate instructions for attachment location and other details.

11. Connect the strain relief (restraining device) BEFORE starting the Combi

12. If the strain relief (restraining device) must be disconnected, it must be reconnected

after the Combi has been returned to its originally installed position BEFORE restarting the Combi.

13. Prepare the installation location as described in the Combi Installation Manual.

14. For GAS (OGB, OGS) Combis:

connector that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 / CSA 6.16, and a quick disconnect device that complies with the Standard for Quick Disconnect Devices f or Use With Gas Fuel, ANSI Z21.41 / CSA 6.9.

15. The appliance shall be installed using flexible conduit.

16. Mechanically secure the flexible conduit to the Combi’s electrical access hole.

The installation of the gas supply shall be made with a

1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com

Cleveland Range,

LLC

SINCE 1922

INNOVATIVE STEAM COOKING SOLUTIONS

by

7

COMBI OVEN-STEAMER

Featuring the

"Advanced Closed

MODEL: c OGB-10.10

CAPACITY: TEN (10) – 12" by 20" by 2 1/2" steam table pans

System +3"

GAS Fired – with Steam Generator

Cooking Modes:

■

Hot Air

■

Steam

■

Combi

Cleveland Standard Features:

■

"Advanced closed system" with "Crisp & Tasty" de-moisturizing feature

■

High efficiency, power burner heating system for hot air and steam generator saves energy and provides fast heat up times

■

Fully insulated steam generator and cooking compartment for maximum energy savings

■

Polished cooking compartment with coved corners for easy cleaning

■

Three (3) 12" x 20" wire shelves

■

Hinged fan guard and hinged removable pan racks

■

Two (2) speed auto reversing convection fan for even heat distribution

■

Space saving, easy to close "Disappearing Door"

■

Door latch with safety vent position and wear-free door switch

■

Vented, double glass door with integrated door stop and self draining condensate drip pan

■

Easy to change, press-fit door seal

■

Oven light with shock resistant safety glass

■

Multipoint core temperature probe

■

Easy to use electronic controls for all operational functions

■

Self diagnostic system with full text message display

■

Easy to understand menu icons with bright graphics display

■

User friendly selector dial

■

Exclusive "Smart Key" for selecting option settings

■

Digital controls for temperature, time and core probe settings

■

Eight (8) "Press & Go" one step, recipe start buttons

■

Cook book library for up to 250 stored recipe programs, each recipe capable of 20 steps

■

RS 232 connection for controlling one unit with a PC (personal computer)

■

Memory module automatically saves unit settings and recipes

■

Manual program override feature for operational settings

■

Smooth action hand shower for compartment cleaning

Gas Fired Steam Generator

■

Quiet, high efficiency, power burner heating system

■

Built-in automatic rinse system

■

Automatic fill and water level control

■

Automatic generator drain

■

Retherm

■

"Cook & Hold"

■

"Delta T" slow cooking

■

"Crisp & Tasty"

IT EM NUMBE R __________________________________________

JOB NAME / NUMBER __________________________________

Shall be Cleveland Model: OGB-10.10 Combination Convection Oven / Steamer with simple to operate electronic programmable controls for Hot Air, Convection Steam, and Combination cooking modes, "Cook & Hold" and "Delta T" slow-cooking capabilities, "Advanced Closed System" with "Crisp & Tasty" de-moisturizing feature. Multiple cooking stage programs, stored recipe library, multipoint core temperature probe, "Press & Go", one-step recipe start buttons, "Smart Key" for selecting option settings, Two (2) speed auto reversing convection fan. Quiet, high efficiency power burner heating system; steam generator with automatic drain. "Disappearing Door". Capacity for ten (10) 12" x 20" x 2 1/2" pans.

Options and Accessories

❐ ConvoClean automatic compartment washing system ❐ PC-HACCP software for establishing "HACCP controls" and automatic

documentation of the cooking process

❐ Equipment stand(s) ❐ Equipment stand(s) with Casters ❐ Stacking kit for mounting one (1) OGB-6.10 model on top of

one (1) OGB-10.10

❐ Lockable cover over operating controls for prison installations ❐ USB or RS 485 connection for networking and controlling up to 32 units

with a personal computer

❐ Propane gas option ❐ Flue diverter ❐ Plate rack for banquet operations ❐ Plate rack cart ❐ Thermal cover for plate or pan rack ❐ ConvoClean compartment cleaning solution ❐ ConvoCare concentrate for compartment rinse cycle ❐ "Dissolve" generator descaling solution ❐ Chicken Grill Rack ❐ 12" x 20" Wire Baskets for frying products ❐ Additional 12" x 20" Wire Shelves

Short Form Specifications

SECT. IIC PAGE 17

0406

36.70"

2.52"

1.58"

38.98"

6.00"

1.82"

44.98"

31.70"

2.80"

11. 11"

2.80"

6.97"

3.39"

2.60"

6.46"

10.79"

3.23"

9.45"

9.30"

30.20"

3.27"

6.07"

12.45"

2.96"

17.60"

1.19"

19.30"

6.34"

3.00"

4.97"

S

AV

E1

E2

RC

CS

W1

W2

D

G

FRONT VIEW

TOP VIEW

BOTTOM VIEW

23.63"

2.01"

36.70"

2.52"

1.58"

38.98"

6.00"

1.82"

44.98"

31.70"

2.80"

6.96"

11. 11"

2.80"

3.39"

6.46"

10.79"

3.23"

9.45"

9.30"

30.20"

3.27"

6.07"

12.45"

2.96"

17.60"

1.19"

19.30"

6.34"

3.00"

4.97"

S

AV

E1

RC

CS

W1

W2

D

G

FRONT VIEW

TOP VIEW

BOTTOM VIEW

23.63"

2.01"

W1

W2

D

W

1

W2

D

RC

S

CS

AV

G

W1

W2

D

W1

W2

D

RC

W1

W2

D

RC

CS

W1

W2

D

RC

S

CS

AV

W1

W2

D

RC

S

CS

AV

G

E1

W1

W2

D

RC

S

CS

AV

G

E1

E2

W1

W2

D

RC

CS

AV

W1

W2

8

The "Advanced Closed System" offers the following advantages:

■

Saves energy

■

Automatic moisture level adjustment

■

Low heat and steam emission to the kitchen

■

Automatically regulated steam injection

■

Enables immediate change into the steam mode

■

"Crisp & Tasty" demoisturizing function

Model: OGB-10.10

Pan Capacity [

10 (12" x 20" x 2 1/2") steam table pans 11 (12" x 20" x 1") steam table pans 11 (13" x 20") half size wire racks 11 (13" x 18") half size sheet pans 10 (12" x 20") frying baskets - (no wire racks needed)

Unit has 11 slide rails at 2.64" (67mm) apart

]:

For Banquet Operations: Optional Plate Rack holds 32 plates

Unit Dimensions: Width - 41.04", Depth - 34.50", Height - 45.68"

Shipping Dimensions: Width - 47", Depth - 41", Height - 54"

(including packaging)

Shipping Weight: 475 Lbs

Required Clearances:

• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located

Rear - 2", Left Side - 4", Right Side - 2 1/2"

next to the unit.

• Allow for sufficient clearance on left side for service access (contact the factory service department for recommendations).

• Installation must comply with all local fire and health codes.

Agency Approvals: UL - Gas, UL - Sanitation (NSF Standards)

Electrical Requirements: 120 volt, 11.7 amps, 60 Hz, single phase

Gas Connection: 3/4" NPT

Gas Type: Natural Gas (Propane optional) Gas Flow Pressure: Natural Gas - Min. 5.5" WC / Max. 14" WC

Propane Gas - Min. 11" WC / Max. 14" WC Total Connected Load: 75,700 BTU (68,000 BTU Propane) Steam Generator: 68,200 BTU (61,000 BTU Propane) Hot Air: 75,700 BTU (68,000 BTU Propane)

Water Connections: Cold Water (drinking water quality) Flow Pressure: 30 - 60 PSI Water Inlets: 3/4" GHT-F (Female Garden Hose Connection)

Treated Water for Steam Generator

Untreated Water for Condenser and Hand Shower

Drain Connection: 2" Tube

Venting: Exhaust Hood required

Gas Exhaust for Hot Air Heating

Gas Exhaust for Steam Generator

Air Vent

*Connection for Cleaning Solution

NOTES:

Cleveland Range reserves right of design improvement or modification, as warranted. Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes. Cleveland Range equipment is built to comply with applicable standards for manufacturers.

*Connection for Rinse Cycle

Low Pressure Safety Valve

Available as an option

*

SECT. IIC PAGE 18

0406

1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com

Cleveland Range,

LLC

SINCE 1922

INNOVATIVE STEAM COOKING SOLUTIONS

by

9

COMBI OVEN-STEAMER

Featuring the

"Advanced Closed

MODEL: c OGS-10.10

CAPACITY: TEN (10) – 12" by 20" by 2 1/2" steam table pans

System +3"

GAS Fired – Boilerless

Cooking Modes:

■

Hot Air

■

Steam

■

Combi

Cleveland Standard Features:

■

"Advanced closed system" with "Crisp & Tasty" de-moisturizing feature

■

High efficiency, power burner heating system

■

Fully insulated cooking compartment for maximum energy savings

■

Polished cooking compartment with coved corners for easy cleaning

■

Three (3) 12" x 20" wire shelves

■

Hinged fan guard and hinged removable pan racks

■

Two (2) speed auto reversing convection fan for even heat distribution

■

Space saving, easy to close "Disappearing Door"

■

Door latch with safety vent position and wear-free door switch

■

Vented, double glass door with integrated door stop and self draining condensate drip pan

■

Easy to change, press-fit door seal

■

Oven light with shock resistant safety glass

■

Multipoint core temperature probe

■

Easy to use electronic controls for all operational functions

■

Self diagnostic system with full text message display

■

Easy to understand menu icons with bright graphics display

■

User friendly selector dial

■

Exclusive "Smart Key " for selecting option settings

■

Digital controls for temperature, time and core probe settings

■

Eight (8) "Press & Go" one step, recipe start buttons

■

Cook book library for up to 250 stored recipe programs, each recipe capable of 20 steps

■

RS 232 connection for controlling one unit with a PC (personal computer)

■

Memory module automatically saves unit settings and recipes

■

Manual program override feature for operational settings

■

Smooth action hand shower for compartment cleaning

■

Injection system for steam

Options and Accessories

❐ ConvoClean automatic compartment washing system ❐ PC-HACCP software for establishing "HACCP controls" and

automatic documentation of the cooking process

❐ Equipment stand(s) ❐ Equipment stand(s) with Casters ❐ Stacking kit for mounting one (1) OGS-6.10 model on top of

one (1) OGS-10.10

■

Retherm

■

"Cook & Hold"

■

"Delta T" slow cooking

■

"Crisp & Tasty"

IT EM NUMBE R __________________________________________

JOB NAME / NUMBER __________________________________

Shall be Cleveland Model: OGS-10.10 Combination Convection Oven / Steamer with simple to operate electronic programmable controls for Hot Air, Convection Steam, and Combination cooking modes, "Cook & Hold" and "Delta T" slow-cooking capabilities, "Advanced Closed System" with "Crisp & Tasty" de-moisturizing feature. Multiple cooking stage programs, stored recipe library, multipoint core temperature probe, "Press & Go", one-step recipe start buttons, "Smart Key" for selecting option settings, two (2) speed auto reversing convection fan. Quiet, high efficiency power burner heating system; boilerless. "Disappearing Door". Capacity for ten (10) 12" x 20" x 2 1/2" pans.

❐ Lockable cover over operating controls for prison installations ❐ USB or RS 485 connection for networking and controlling up to 32

units with a personal computer

❐ Propane gas option ❐ Flue diverter ❐ Plate rack for banquet operations ❐ Plate rack cart ❐ Thermal cover for plate or pan rack ❐ ConvoClean compartment cleaning solution ❐ ConvoCare concentrate for compartment rinse cycle ❐ "Dissolve" generator descaling solution ❐ Chicken Grill Rack ❐ 12" x 20" Wire Baskets for frying products ❐ Additional 12" x 20" Wire Shelves

Short Form Specifications

SECT. IIC PAGE 45

0406

W1

W2

D

RC

W1

W2

D

RC

CS

W1

W2

D

RC

S

CS

AV

OGS 10.10

A = Water hook up soft water G" B = Water hook up cold water G" C = Drainage hook up DN50 D = Power hook up E = Potential equaliser F = Final rinse hook up G = Cleaner hook up H = Air vent pipe I = Low pressure safety

J = Gas hook up R" K = Exhaust pipe gas

36.70"

2.52"

1.58"

38.98"

6.00"

1.82"

44.98"

31.70"

2.80"

6.96"

11. 11"

2.80"

3.39"

6.46"

10.79"

3.23"

9.45"

9.30"

30.20"

3.27"

6.07"

12.45"

2.96"

17.60"

1.19"

19.30"

6.34"

3.00"

4.97"

S

AV

E1

RC

CS

W1

W2

D

G

FRONT VIEW

TOP VIEW

BOTTOM VIEW

23.63"

2.01"

W1

W2

D

W1

W2

D

RC

S

CS

AV

G

W1

W2

D

W1

W2

D

RC

S

CS

AV

G

E1

W1

W2

D

RC

CS

AV

W1

W2

10

The "Advanced Closed System" offers the following advantages:

■

Saves energy

■

Automatic moisture level adjustment

■

Low heat and steam emission to the kitchen

■

Automatically regulated steam injection

■

Enables immediate change into the steam mode

■

"Crisp & Tasty" demoisturizing function

Model: OGS-10.

Pan Capacity [

10 (12" x 20" x 2 1/2") steam table pans 11 (12" x 20" x 1") steam table pans 11 half size wire racks (13" x 20") 11 (13" x 18") half size sheet pans 10 (12" x 20") frying baskets - (no wire racks needed)

For Banquet Operations: Optional Plate Rack holds 32 plates

Unit has 11 slide rails at 2.64" (67mm) apart

10

]:

Unit Dimensions:

Shipping Dimensions: Width - 47", Depth - 41", Height - 54"

(including packaging)

Shipping Weight: 475 Lbs

Required Clearances:

• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located

next to the unit.

• Allow for sufficient clearance on left side for service access (contact the

factory service department for recommendations).

• Installation must comply with all local fire and health codes.

Agency Approvals:

Electrical Requirements: 120 volt, 11.7 amps, 60 Hz, single phase

Do not connect to a G.F.I. outlet

Gas Connection: 3/4" NPT Gas Type: Natural Gas (Propane optional) Gas Flow Pressure: Natural Gas - Min. 5.5" WC / Max. 14" WC

Total Connected Load: Hot Air:

Water Connections: Cold Water (drinking water quality) Flow Pressure: 30 - 60 PSI Water Inlets: 3/4" GHT-F (Female Garden Hose Connection)

Width - 41.04", Depth - 34.50", Height - 45.68"

Rear - 2", Left Side - 4", Right Side - 2 1/2"

UL - Gas, UL - Sanitation (NSF Standards)

Propane Gas - Min. 11" WC / Max. 14" WC

75,700 BTU (68,000 BTU Propane)

Treated Water for Steam Production

NOTES:

Cleveland Range reserves right of design improvement or modification, as warranted. Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes. Cleveland Range equipment is built to comply with applicable standards for manufacturers.

Untreated Water for Condenser and Hand Shower

Drain Connection: 2" Tube

Venting: Exhaust Hood required

Gas Exhaust for Hot Air Heating

Air Vent

*Connection for Cleaning Solution

*Connection for Rinse Cycle

Low Pressure Safety Valve

*Available as an option

SECT. IIC PAGE 46

0406

1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com

Cleveland Range,

LLC

SINCE 1922

INNOVATIVE STEAM COOKING SOLUTIONS

by

11

COMBI OVEN-STEAMER

Featuring the

"Advanced Closed

MODEL: c OGB-6.20

CAPACITY: Seven (7) – 18" by 26" full size sheet pans or

System +3"

GAS Fired – with Steam Generator

Cooking Modes:

■

Hot Air

■

Steam

■

Combi

Cleveland Standard Features:

■

"Advanced closed system" with "Crisp & Tasty" de-moisturizing feature

■

High efficiency, power burner heating system for hot air and steam generator saves energy and provides fast heat up times

■

Fully insulated steam generator and cooking compartment for maximum energy savings

■

Polished cooking compartment with coved corners for easy cleaning

■

Three (3) 26" x 20" wire shelves

■

Hinged fan guard and hinged removable pan racks

■

Two (2) speed auto reversing convection fan for even heat distribution

■

Space saving, easy to close "Disappearing Door"

■

Door latch with safety vent position and wear-free door switch

■

Vented, double glass door with integrated door stop and self draining condensate drip pan

■

Easy to change, press-fit door seal

■

Oven light with shock resistant safety glass

■

Multipoint core temperature probe

■

Easy to use electronic controls for all operational functions

■

Self diagnostic system with full text message display

■

Easy to understand menu icons with bright graphics display

■

User friendly selector dial

■

Exclusive "Smart Key" for selecting option settings

■

Digital controls for temperature, time and core probe settings

■

Eight (8) "Press & Go" one step, recipe start buttons

■

Cook book library for up to 250 stored recipe programs, each recipe capable of 20 steps

■

RS 232 connection for controlling one unit with a PC (personal computer)

■

Memory module automatically saves unit settings and recipes

■

Manual program override feature for operational settings

■

Smooth action hand shower for compartment cleaning

Gas Fired Steam Generator

■

Quiet, high efficiency, power burner heating system

■

Built-in automatic rinse system

■

Automatic fill and water level control

■

Automatic generator drain

■

Retherm

■

"Cook & Hold"

■

"Delta T" slow cooking

■

"Crisp & Tasty"

IT EM NUMBE R __________________________________________

JOB NAME / NUMBER __________________________________

Shall be Cleveland Model: OGB-6.20 Combination Convection Oven / Steamer with simple to operate electronic programmable controls for Hot Air, Convection Steam, and Combination cooking modes, "Cook & Hold" and "Delta T" slowcooking capabilities, moisturizing feature. Multiple cooking stage programs, stored recipe library, multipoint core temperature probe, "Press & Go", one-step recipe start buttons, "Smart Key" for selecting option settings, Two (2) speed auto reversing convection fan. Quiet, high efficiency power burner heating system; steam generator with automatic drain. "Disappearing Door" x 26" full size sheet pans, or fourteen (14) 12" x 20" x 2 1/2" pans.

Options and Accessories

❐ ConvoClean automatic compartment washing system ❐ PC-HACCP software for establishing "HACCP controls" and automatic

documentation of the cooking process

❐ Equipment stand(s) ❐ Equipment stand(s) with Casters ❐ Stacking kit for stacking two (2) OGB-6.20 models ❐ Stacking kit for mounting one (1) OGB-6.20 model on top of

one (1) OGB-10.20

❐ Universal pan-rack system to hold full size sheet pans without the use of wire

shelves

❐ Lockable cover over operating controls for prison installations ❐ USB or RS 485 connection for networking and controlling up to 32 units with a

personal computer

❐ Propane gas option ❐ Flue diverter ❐ Plate rack for banquet operations ❐ Plate rack cart ❐ Thermal cover for plate or pan rack ❐ ConvoClean compartment cleaning solution ❐ ConvoCare concentrate for compartment rinse cycle ❐ "Dissolve" generator descaling solution ❐ Chicken Grill Rack ❐ 12" x 20" Wire Baskets for frying products ❐ Additional 26" x 20" Wire Shelves ❐ Special Baking Rack System

Fourteen (14) – 12" by 20" by 2 1/2" steam table pans

Short Form Specifications

"Advanced Closed System"

with "Crisp & Tasty" de-

. C

apacity for seven (7) 18"

SECT. IIC PAGE 21

0406

47.92"

2.52"

1.58"

30.12"

6.00"

1.82"

36.12"

40.44"

2.80"

12.68"

2.80"

8.55"

3.39"

3.55"

7.49"

10.79"

3.23"

14.26"

10.87"

41.42"

3.27"

6.93"

10.40"

21.19"

2.96"

27.29"

1.19"

29.61"

3.90"

3.00"

4.97"

S

AV

E1

E2

RC

CS

W1

W2

D

G

FRONT VIEW

TOP VIEW

40.44"

2.80"

12.68"

2.80"

8.55"

3.39"

7.49"

10.79"

S

AV

E1

TOP VIEW

BOTTOM VIEW

3.23"

14.26"

10.87"

41.42"

3.27"

6.93"

10.40"

21.19"

2.96"

27.29"

1.19"

29.61"

3.90"

3.00"

4.97"

RC

CS

W1

W2

D

G

BOTTOM VIEW

47.92"

2.52"

1.58"

30.12"

6.00"

1.82"

36.12"

FRONT VIEW

31.50"

W1

W2

D

W

1

W2

D

RC

S

CS

AV

G

W1

W2

D

W1

W2

D

RC

W1

W2

D

RC

CS

W1

W2

D

RC

S

CS

AV

W1

W2

D

RC

S

CS

AV

G

E1

W1

W2

D

RC

S

CS

AV

G

E1

E2

W1

W2

D

RC

CS

AV

W1

W2

12

The "Advanced Closed System" offers the following advantages:

■

Saves energy

■

Low heat and steam emission to the kitchen

■

Automatically regulated steam injection

■

Enables immediate change into the steam mode

■

"Crisp & Tasty" demoisturizing function

Model: OGB-6.20

■

Automatic moisture level adjustment

Pan Capacity [

7 (20" x 26") full size wire racks 7 (18" x 26") full size sheet pans - on wire racks

(13" x 18") half size sheet pans - on wire racks 14 (12" x 20" x 2 1/2") steam table pans

14 14 (12" x 20" x 1") steam table pans 14 (12" x 20") frying Baskets - (no wire racks needed)

For Banquet Operations: Optional Plate Rack holds 42 plates

Unit has 7 slide rails at 2.64" (67mm) apart

]:

Unit Dimensions: Width - 52.26", Depth - 43.24", Height - 36.82"

Shipping Dimensions: Width - 58", Depth - 49", Height - 45"

(including packaging)

Shipping Weight: 485 Lbs

Required Clearances:

• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located

Rear - 2", Left Side - 4", Right Side - 2 1/2"

next to the unit.

• Allow for sufficient clearance on left side for service access (contact the

factory service department for recommendations).

• Installation must comply with all local fire and health codes.

Agency Approvals: UL - Gas, UL - Sanitation (NSF Standards)

Electrical Requirements: 120 volt, 11.7 amps, 60 Hz, single phase

Do not connect to a G.F.I. outlet

Gas Connection: 3/4" NPT Gas Type: Natural Gas (Propane optional) Gas Flow Pressure: Natural Gas - Min. 5.5" WC / Max. 14" WC

Propane Gas - Min. 11" WC / Max. 14" WC Total Connected Load: 75,700 BTU (68000 BTU Propane) Steam Generator: 68,200 BTU (61,000 BTU Propane) Hot Air: 75,700 BTU (68,000 BTU Propane)

Water Connections: Cold Water (drinking water quality) Flow Pressure: 30 - 60 PSI Water Inlets: 3/4" GHT-F (Female Garden Hose Connection)

Drain Connection: 2" Tube

Treated Water for Steam Generator

Untreated Water for Condenser and Hand Shower

Venting: Exhaust Hood required

NOTES:

Cleveland Range reserves right of design improvement or modification, as warranted. Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes. Cleveland Range equipment is built to comply with applicable standards for manufacturers.

*Connection for Cleaning Solution

*Connection for Rinse Cycle

Low Pressure Safety Valve

Available as an option

*

Gas Exhaust for Hot Air Heating

Gas Exhaust for Steam Generator

Air Vent

SECT. IIC PAGE 22

0406

1333 East 179th St., Cleveland, Ohio, U.S.A. 44110 Ph: 1-216-481-4900 Fx: 1-216-481-3782 Web Site: www.clevelandrange.com

Cleveland Range,

LLC

SINCE 1922

INNOVATIVE STEAM COOKING SOLUTIONS

by

13

COMBI OVEN-STEAMER

Featuring the

"Advanced Closed

MODEL: c OGS-6.20

CAPACITY: Seven (7) – 18" by 26" full size sheet pans or

System +3"

GAS Fired – Boilerless

Cooking Modes:

■

Hot Air

■

Steam

■

Combi

Cleveland Standard Features:

■

"Advanced closed system" with "Crisp & Tasty" de-moisturizing feature

■

High efficiency, power burner heating system

■

Fully insulated cooking compartment for maximum energy savings

■

Polished cooking compartment with coved corners for easy cleaning

■

Three (3) 26" x 20" wire shelves

■

Hinged fan guard and hinged removable pan racks

■

Two (2) speed auto reversing convection fan for even heat distribution

■

Space saving, easy to close "Disappearing Door"

■

Door latch with safety vent position and wear-free door switch

■

Vented, double glass door with integrated door stop and self draining condensate drip pan

■

Easy to change, press-fit door seal

■

Oven light with shock resistant safety glass

■

Multipoint core temperature probe

■

Easy to use electronic controls for all operational functions

■

Self diagnostic system with full text message display

■

Easy to understand menu icons with bright graphics display

■

User friendly selector dial

■

Exclusive "Smart Key" for selecting option settings

■

Digital controls for temperature, time and core probe settings

■

Eight (8) "Press & Go" one step, recipe start buttons

■

Cook book library for up to 250 stored recipe programs, each recipe capable of 20 steps

■

RS 232 connection for controlling one unit with a PC (personal computer)

■

Memory module automatically saves unit settings and recipes

■

Manual program override feature for operational settings

■

Smooth action hand shower for compartment cleaning

■

Injection system for steam

Options and Accessories

❐ ConvoClean automatic compartment washing system ❐ PC-HACCP software for establishing "HACCP controls" and

automatic documentation of the cooking process

❐ Equipment stand(s) ❐ Equipment stand(s) with Casters ❐ Stacking kit for stacking two (2) OGS-6.20 models

■

Retherm

■

"Cook & Hold"

■

"Delta T" slow cooking

■

"Crisp & Tasty"

IT EM NUMBE R __________________________________________

JOB NAME / NUMBER __________________________________

Shall be Cleveland Model: OGS-6.20 Combination Convection Oven / Steamer with simple to operate electronic programmable controls for Hot Air, Convection Steam, and Combination cooking modes, "Cook & Hold" and "Delta T" slow-cooking capabilities, "Advanced Closed System" with "Crisp & Tasty" de-moisturizing feature. Multiple cooking stage programs, stored recipe library, multipoint core temperature probe, "Press & Go", one-step recipe start buttons, "Smart Key" for selecting option settings, two (2) speed auto reversing convection fan. Quiet, high efficiency power burner heating system; boilerless. " size sheet pans, or fourteen (14) 12" x 20" x 2 1/2" pans.

❐ Stacking kit for mounting one (1) OGS-6.20 model on top of

one (1) OGS-10.20

❐ Universal pan-rack system to hold full size sheet pans without the

use of wire shelves

❐ Lockable cover over operating controls for prison installations ❐ USB or RS 485 connection for networking and controlling up to 32

units with a personal computer

❐ Propane gas option ❐ Flue diverter ❐ Plate rack for banquet operations ❐ Plate rack cart ❐ Thermal cover for plate or pan rack ❐ ConvoClean compartment cleaning solution ❐ ConvoCare concentrate for compartment rinse cycle ❐ "Dissolve" generator descaling solution ❐ Chicken Grill Rack ❐ 12" x 20" Wire Baskets for frying products ❐ Additional 26" x 20" Wire Shelves

❐ Special Baking Rack System

Fourteen (14) – 12" by 20" by 2 1/2" steam table pans

Short Form Specifications

Disappearing Door". Capacity for seven (7) 18" x 26" full

SECT. IIC PAGE 49

0406

W1

W2

D

RC

W1

W2

D

RC

CS

W1

W2

D

RC

S

CS

AV

OGS 6.20

A = Water hook up soft water G" B = Water hook up cold water G" C = Drainage hook up DN50 D = Power hook up E = Potential equaliser F = Final rinse hook up G = Cleaner hook up H = Air vent pipe I = Low pressure safety

J = Gas hook up R" K = Exhaust pipe gas

40.44"

2.80"

12.68"

2.80"

8.55"

3.39"

7.49"

10.79"

S

AV

E1

TOP VIEW

3.23"

14.26"

10.87"

41.42"

3.27"

6.93"

10.40"

21.19"

2.96"

27.29"

1.19"

29.61"

3.90"

3.00"

4.97"

RC

CS

W1

W2

D

G

BOTTOM VIEW

47.92"

2.52"

1.58"

30.12"

6.00"

1.82"

36.12"

FRONT VIEW

31.50"

W1

W2

D

W1

W2

D

RC

S

CS

AV

G

W1

W2

D

W1

W2

D

RC

S

CS

AV

G

E1

W1

W2

D

RC

CS

AV

W1

W2

14

The "Advanced Closed System" offers the following advantages:

■

Saves energy

■

Automatic moisture level adjustment

■

Low heat and steam emission to the kitchen

■

Automatically regulated steam injection

■

Enables immediate change into the steam mode

■

"Crisp & Tasty" demoisturizing function

Model: OGS-6.20

Pan Capacity [

7 (20" x 26") full size wire racks 7 (18" x 26") full size sheet pans - on wire racks

(13" x 18") half size sheet pans - on wire racks 14 (12" x 20" x 2 1/2") steam table pans

14 14 (12" x 20" x 1") steam table pans 14 (12" x 20") frying Baskets - (no wire racks needed)

For Banquet Operations: Optional Plate Rack holds 42 plates

Unit Dimensions:

Shipping Dimensions: Width - 58", Depth - 49", Height - 45"

(including packaging)

Shipping Weight: 485 Lbs

Required Clearances:

• Allow for sufficient distance if a "high heat source" (i.e. Broiler) is located

next to the unit.

• Allow for sufficient clearance on left side for service access (contact the

factory service department for recommendations).

• Installation must comply with all local fire and health codes.

Agency Approvals:

Electrical Requirements: 120 volt, 11.7 amps, 60 Hz, single phase

Do not connect to a G.F.I. outlet

Gas Connection: 3/4" NPT Gas Type: Natural Gas (Propane optional) Gas Flow Pressure: Natural Gas - Min. 5.5" WC / Max. 14" WC

Total Connected Load: Hot Air:

Water Connections: Cold Water (drinking water quality) Flow Pressure: 30 - 60 PSI Water Inlets: 3/4" GHT-F (Female Garden Hose Connection)

Unit has 7 slide rails at 2.64" (67mm) apart

Width - 52.26", Depth - 43.24", Height - 36.82"

Rear - 2", Left Side - 4", Right Side - 2 1/2"

UL - Gas, UL - Sanitation (NSF Standards)

Propane Gas - Min. 11" WC / Max. 14" WC

75,700 BTU (68,000 BTU Propane)

Treated Water for Steam Production

]:

NOTES:

Cleveland Range reserves right of design improvement or modification, as warranted. Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes. Cleveland Range equipment is built to comply with applicable standards for manufacturers.

Untreated Water for Condenser and Hand Shower

Drain Connection: 2" Tube

Venting: Exhaust Hood required

Gas Exhaust for Hot Air Heating

Air Vent

*Connection for Cleaning Solution

*Connection for Rinse Cycle

Low Pressure Safety Valve

*Available as an option

SECT. IIC PAGE 50

0406

CONTROL PANEL

15

BASIC OPERATION

A. QUICK START GUIDE ALWAYS PRE-HEAT THE OVEN CHAMBER!

1. Switch on with key (1).

2. Select cooking mode with keys (2-5).

3. Press key (6) to start.

OR

1. Press key (18) and rotate Selector Dial (23) to set oven temperature.

2. Press key (19) and rotate Selector Dial (23) to set cooking time.

OR

1. Press key (20) and rotate Selector Dial (23) to set core temperature.

ALL

1. Press key (6) to start the Combi.

2. To change the settings while cooking: press keys (18) OR (19) OR (20) and adjust the settings with the Selector Dial (23).

3. When the buzzer sounds press key (6) or open the door.

NOTES: See “CONTROL PANEL DETAIL VIEW” in Chapter 4, Section B for detailed descriptions of control panel functions.

Figure 4-1a

Control Panel

B. CONTROL PANEL DETAIL VIEW

16

Note: Item numbers correspond to numbers on the

control panels in Figure 4-1b

1. ON/OFF

When the Combi is turned ON:

• Self-diagnosis is performed.

• Oven light turns on.

• Steam generator fills and heats (OEB and OGB

models).

Cooking Modes

2. Steam

• Oven temperature is continuously variable between 86°F and 248°F.

3. Combi Hot Air and Steam

• Oven temperature is continuously variable between 212°F and 482°F.

4. Hot Air

• Oven temperature is continuously variable between 86°F and 482°F.

5. Retherm

• Oven temperature is continuously variable between 248°F and 320°F.

6. Start/Stop

• Start cooking modes and recipes.

• Stop the cooking activity.

• Escape or Exit Smart Key functions

Programming / Help

7. Cookbook

• Call up, exit cookbook.

• View a list of stored recipes in the display.

8. Smart Key

• Set Extra Functions.

• Set-Up the Combi.

• Enter Sub-Menus.

9. Edit

• Create, change, copy, and delete recipes.

Figure 4-1b

Control Panel

Function Indicators

17

• Light up when function or activity is engaged:

10. Reduced Power

11. Burner or Electric Heating ON

12. Reduced Fan Speed

13. Cooking Mode Engaged

14. Button Lock

15. Crisp & Tasty Engaged

16. Program Protection

17. Display

• Display in normal mode:

• Date.

• Time.

• Oven Temperature.

• Cooking Time

• Core Probe Temperature.

• Display in programming mode:

• Clear text.

• Memory.

• Symbols.

Settings

18. Oven Temperature

• Set the nominal oven temperature.

• View the actual or nominal oven

temperature.

19. Cooking Time

• Set the cooking time from 1 minute to 9 hours, 59 minutes using the Selector Dial.

• Set Continuous Mode

1. At 9:59 or 0:01, release the Selector Dial.

2. Turn the Selector Dial again to the left

or right.

• See the actual or nominal cooking time.

• See elapsed cooking time when using

Core Temperature mode.

20. Core Temperature

• Set the nominal core temperature.

• See the actual or nominal core

temperature.

• See the actual core temperature during cooking time mode.

21 & 22. Scroll Left and Scroll Right

• Page / Scroll one step forward or back in programming mode.

23. Selector Dial

• Set: Oven temperature, cooking time, core temperature, recipe name, recipe number.

• Select Smart Key functions, editing functions and recipes in the cookbook.

24. Press & Go Keys

• Start saved recipes with one key.

• LED below key lights up when

corresponding recipe is started.

Notes:

• Magnetic door switch

If the oven door is opened during operation, the magnetic door switch automatically interrupts the recipe. The timer stops. After closing the oven door, the Combi automatically continues the recipe. If the oven door is opened when the buzzer sounds at the end of a recipe, it automatically switches off.

• Operate controls with hands only!

AT THE END OF THE DAY OR SHIFT

18

A. Cleaning the Oven Chamber

1. Cleaning – General

a. Regular cleaning of the Combi after use, inside and out, helps guarantee many years of

b. Clean and maintain the Combi ONLY when the Combi is cold. c. Use the hand shower only inside the oven chamber. d. Clean the outside the Combi by hand. e. Never use the hand shower, hose, pressure washer or similar device on the outside of

f. NEVER spray anything on or into the air intakes or outlets of the Combi. g. Do NOT use hoses, pressure washers, high-pressure cleaners, or water jets to clean

h. Do NOT spray water into a hot oven chamber. i. Use only genuine Convotherm by Cleveland and Cleveland Range cleaning and

j. Never use irritant, acidic, highly alkaline cleaners, high-alcohol, chlorine, chlorinated, or

k. Poor water quality can cause discoloration inside the oven chamber. Remove these

l. Damage caused as a result of improper cleaning voids the warranty.

2. Semi-Automatic and Automatic Cleaning - General

a. If the oven chamber is very heavily soiled, additional manual cleaning may be necessary. b. Depending on the level of soiling of the oven chamber, the engaging frames and grills

c. Do NOT interrupt the semi-automatic or automatic cleaning process.

Clean the oven chamber at least once per day or more frequently as needed

Failure to clean the Combi properly and regularly can cause equipment damage.

Damage caused by improper cleaning will invalidate the Warranty!

satisfaction from your Combi.

the Combi.

inside the Combi oven chamber.

descaling products. Follow the instructions and heed and obey the warnings on the labels. Other products can cause injury, present heath hazards, and damage the Combi.

abrasive cleaning agents, scrapers, or abrasive materials to clean the Combi.

discolorations with CONVOCare. Spray CONVOCare on the affected surfaces in a COLD oven chamber, wait 10 minutes, wipe off with a soft cloth or sponge, and begin cleaning as usual.

may be left in the oven during the automatic cleaning process.

CAUTION

WARNING

19

When working with cleaning agents, nozzle rinsing fluid and spray bottles: Wear suitable clothing, protective gloves and protective goggles to help protect from splashes and spills. Failure to do so can result in chemical burns on skin and in eyes.

3. Manual Cleaning of the Oven Chamber

Read, understand, and heed and obey all instructions and safety information found on cleaning agent labels, Material Safety Data Sheets, and related documents and sources. Failure to do so can result in death, injury, and equipment damage.

a. Clean the Combi daily to prevent discoloration and corrosion of the stainless steel.

1) Avoid scratching the oven chamber or engaging frame.

2) Scratches can collect soil and / or allow corrosion to begin.

3) Do NOT use harsh or abrasive cleaning agents, scouring pads, or scrapers.

b. Clean the fan guard and the fan area behind the fan guard at the same time.

1) Release the quick-action locks on the oven racks and fan guard.

2) Pivot the oven racks and fan guard out into the oven chamber.

3) After cleaning, push the oven racks and fan guard closed and fix them in place with the quick-action locks.

WARNING

CAUTION

Do NOT use U-Shaped racks that are bent or otherwise damaged in any

way. Pans and accessories placed in damaged racks can tip and spill,

causing burns, injuries and/or equipment damage

4) Make sure that the U-Shaped racks do not become bent; otherwise grills, racks, containers and accessories will no longer be safely supported. If U-Shaped racks become bent then remove the Combi from service and contact your qualified Cleveland Range authorized service representative at once.

c. Clean the interior of the of the double glass doors daily.

1) Release the quick-action locks on the door glass.

2) Clean the glass with a non-abrasive cleaner and a soft cloth.

3) Do not use harsh or abrasive cleaning agents, scouring pads, or scrapers because they will damage the glass.

d. Regular cleaning of the hygienic plug-in gasket (door gasket) increases service life.

1) Wait for the gasket to cool.

2) Clean the gasket with mild, scent free dish detergent and a soft cloth.

3) Do not use harsh or abrasive agents, scouring pads or scrapers because they will damage the gasket.

4) Air dry the gasket.

20

e. Clean the Bypass Measuring Aperture. (Opening in the oven

chamber on the left-hand side, slightly below the door latch. See diagram.)

1) Spray with CONVOClean.

2) Rinse clean with the hand shower.

f. Remove and clean the drain cover.

1) Clean food residue and drippings from the tray and drain in the oven chamber.

2) Spray on original CONVOClean oven chamber cleaner and allow it to take effect.

3) Rinse thoroughly with the hand shower.

g. Clean the drain and make sure that it is not

blocked.

h. Clean the demoisturizing tray (trough shaped area

under the drain cover).

Bypass

i. Clean the door drip tray, appliance drip trays and accessory drip trays.

NOTES:

• If a white deposit forms inside the oven chamber, the water treatment system is not correctly set, or the addition of a water treatment system is required. To remove this deposit, use vinegar and a soft cloth.

• Ask your qualified Cleveland Range authorized service representative about adding or setting a water treatment system.

Drain Cover and Drain

B. Semi-Automatic Cleaning of the Oven Chamber

21

NOTE: Do NOT press the Start/Stop key while using the Semi-automatic Cleaning process. This stops the cleaning process.

WARNING

The Semi-Automatic Cleaning process is designed to be started when the oven chamber temperature is at or below 158°F. Death, injury, and equipment damage can result from starting the Semi-Automatic Cleaning process when the oven chamber is above 158°F.

1. Before starting the Semi-Automatic Cleaning process, make sure the oven chamber is below 158°F by stopping all processes and pressing the Temperature key twice to view the actual temperature.

a. If the oven chamber is above 158°F then open the Combi door and wait 15 minutes. b. Check the oven temperature again.

1) If the oven temperature is at or below 158°F then go to Step 2.

2) If the oven temperature is still above 158°F then wait 15 more minutes and check the oven chamber temperature. Repeat this step as needed until the oven chamber temperature is at or below 158°F and then go to Step 2.

2. See separate instruction sheet P/N 260AYM, “One-Hand Sprayer with Telescoping Wand,” for safety information, detailed instructions for using the sprayer, P/N 111598, and other information.

3. Always wear appropriate protective clothing and equipment when using this Sprayer, including protective gloves and goggles.

4. Close and latch the Combi door.

5. If the Combi is OFF, turn it ON.

6. Press the Smart Key. Various options appear in the display.

7. Use the Selector Dial to select “Cleaning”

8. Confirm by pressing the Smart Key.

9. Confirm “Yes” with the Smart Key. The semi-automatic cleaning process starts.

10. Semi-automatic cleaning uses cooking modes to assist the cleaning process. The display shows the nominal values for the cooking modes.

a. The first step is Hot Air mode at 158°F for 10 minutes, followed by a Signal Tone.

11. After the first Signal Tone, open the oven door, and follow instruction sheet in P/N 260AYM to spray the oven chamber, drain, grills, plates etc. with original Convotherm by Cleveland CONVOClean.

12. Close and latch the Combi door and allow the CONVOClean to take effect. The SemiAutomatic Cleaning mode continues to run.

a. The second step is Steam mode at 86°F for 10 minutes, followed by a Signal Tone.

13. After the second Signal Tone, clean behind the fan guard and the fan area. a. Release the quick-action locks on the oven racks and fan guard. b. Swing the oven racks and fan guard into the oven chamber. c. After cleaning, swing the oven racks and fan guard closed and fix it in place with the quick-action

locks.

14. Close and latch the Combi door. The Semi-Automatic Cleaning mode continues automatically.

.

a. The third step is Steam mode at 86°F for 1 minute. No action is needed.

22

b. The fourth step is Steam at 212°F for 10 minutes, followed by a Signal Tone.

15. Turn OFF the Combi when the Signal Tone sounds.

16. Use the hand shower to rinse thoroughly the oven chamber, accessories, and behind the fan guard.

17. In the case of severe staining or soiling, repeat the cleaning process.

18. After use or after cleaning, leave the Combi door open.

C. CONVOClean Automatic Cleaning System (optional):

23

NOTES:

• Do NOT interrupt the automatic cleaning process. Interrupting and restarting the

Automatic Cleaning System with the ON/OFF key may start a 6 minute forced rinsing of the oven chamber to remove any CONVOClean and CONVOCare residue when the ON/OFF key is turned back ON. The Signal Tone sounds at the end of the forced rinsing cycle and the Combi is ON.

• Do not open the Combi door during the automatic cleaning process, unless the

instruction “Open the door” and “close the door,” appears in the display.

• Pre-clean manually to save water and CONVOClean by selecting a lower cleaning

setting.

• If the security questions are not answered within 5 seconds, the Combi resets itself to the

query level and will not start.

• If the message “No cleaner pressure” appears, check that there is enough CONVOClean

and/or CONVOCare in the correct containers. Refill them if necessary (red hose for CONVOClean, and blue or white hose for CONVOCare).

CAUTION

Always make sure the cleaning agent containers are correctly connected to the Combi

CONVOClean => RED

CONVOCare => BLUE or WHITE

A. See P/N 260AZA, “Instructions for CONVOClean System Start-up Kit,” for hose attachment,

solution mixing, and other information.

B. The CONVOClean Automatic Cleaning Process

1. The oven chamber must be cold

hot, the error message, “oven temp too hi / please wait” appears in the display. If this error message appears, open the Combi door, wait 15 minutes and then try to start the automatic cleaning process. Repeat as needed.

2. Before starting, remove large pieces food or cooking residue from the oven chamber to

help prevent the drain from becoming blocked.

3. Check the level of Convotherm by Cleveland CONVOClean and CONVOCare.

a. The containers must be full. b. The suction pipes must be located in the fluid. c. The hoses must be properly attached to the Combi.

4. Press the Smart Key. Various options appear in the display.

5. Use the Selector Dial to select “CONVOClean system”

6. Confirm by pressing the Smart Key.

7. PRESS the Temperature key and select the cleaning level (1-4) with the Selector Dial.

Approximate run times are listed to help plan use of the CONVOClean system. Times may vary by +/- 15 minutes.

1 “Light Soiling” 55 minutes. 2 “Medium Soiling” 1 hour and 30 minutes.

before starting this process. If the oven chamber is still

.

3 “Strong Soiling” 2 hours.

24

4 ‘Strong Soiling – Shining+” 2 hours and 45 minutes.

8. Press the Smart Key.

9. “Food inside oven?” appears in the display.

10. If the oven is empty, then answer “No.”

11. Confirm by pressing the Smart Key.

12. “Start auto-cleaning?” appears in the display.

13. Answer “Yes.”

14. Confirm by pressing the Smart Key.

15. The CONVOClean system starts.

16. The instruction “open the door” appears in the display to check the function of the

magnetic door switch.

17. Open the Combi door.

18. The instruction “close the door,” appears in the display to check the function of the

magnetic door switch.

19. Close the door.

20. The self test “water supply open?” appears in the display. If the water supply is on (open),

then the self test question disappears from the display. a. If “water supply open?” does not disappear from the display, or “not enough water”

appears in the display, then check the water supply.

b. The CONVOClean system resumes running after the water supply is restored.

21. “Cleaning in progress” appears in the display and the CONVOClean process runs.

22. The Signal Tone sounds at the end of the CONVOClean cycle and “end of cleaning”

appears in the display.

23. Press the Start/Stop key to stop the Signal Tone and end the CONVOClean process.

24. The Combi is ON and ready to use.

25. After use or after cleaning, leave the Combi door open.

DESCALE STEAM GENERATOR

25

A. GENERAL INFORMATION

1. Steam generators should be descaled at least once a month, depending on scale buildup. If you have serious steam generator scale buildup, a water treatment system should be installed for the steamer. If this is not possible, the frequency of descaling should be increased.

2. Cleveland Range, recommends the use of DISSOLVE® Descaler Solution, Cleveland Range Part Number 106174. No other system of steamer descaling should be used.

3. NOTE: Part No. 106174 is the Part No. for a case (6 1-gallon containers) of DISSOLVE descaler.

4. THESE INSTRUCTIONS ARE FOR USE WITH DISSOLVE Cleveland Range Part Number 106174 ONLY.

5. Health Hazard Data, Effects of Overexposure – This product may cause a burning sensation to eyes or skin.

6. Emergency and First Aid Procedures - In case of eye contact, immediately flush eyes with plenty of water. If irritation persists, seek medical attention. In case of skin contact: wash with soap and water. If inhaled, remove to fresh air. If burning persists, call a physician. If swallowed, drink 1 or 2 glasses of water and call a physician.

7. Spill or Leak Procedures – Rinse with plenty of water to dilute. Sodium carbonate or calcium carbonate may be used to soak up liquid. Spent material is considered nonhazardous and may be disposed of in a sewer system with water flush.

WARNING

® DESCALER SOLUTION

®

The liquid solution in Cleveland Range Descaler Solution Part No. 106174, “DISSOLVE® Descaler

Solution,”

can be harmful if not handled properly.

Follow these basic safety rules for handling and using this product to help prevent death or injury:

• Wear protective clothing when mixing or applying chemical cleaners.

• Wear rubber gloves, and OSHA approved eye protection when descaling to help avoid injury.

• Avoid breathing fumes. If liquid comes in contact with skin, wash with soap and water.

• If chemical contacts eyes, flush with water. If irritation persists, seek medical attention

• If chemical is swallowed or ingested, drink 1 or 2 glasses of water and call a physician.

Failure to do so can result in death or injury.

CAUTION

Use ONLY the DISSOLVE® Descaler method using Part No. 106174 to descale the Combi. Read, understand, and follow both the descaling procedure instructions and warnings, and the

instructions and warnings on the DISSOLVE Injury, equipment damage, and property damage can result from using other descaling systems

and/or failing to follow the descaling procedure and DISSOLVE® instructions and warnings.

®

label and MSDS.

g

26

DANGER

B. GENERAL SAFETY FOR DESCALING

1. Always wear suitable protective clothing including appropriate gloves, and eye protection.

2. Read, understand, heed and obey and obey and obey, and follow all directions on the descaler label, MSDS, and related documents

3. Never operate the Combi when descaler has been applied or while descaling.

4. Descale only when the Combi is cold.

5. Immediately wipe up any leaked or spilled descaling fluid

C. COMBI ATMOSPHERIC STEAM GENERATOR DESCALING PROCEDURE

(For DISSOLVE® Descaler Solution Part No. 106174)

This procedure takes approximately 3 hours to complete. Do NOT heat the Combi during descaling.

1. Turn ON the Combi at the Control Power Service Disconnect switch located below the hand shower.

2. Turn ON the Combi with the ON/OFF key.

3. Open the door to the cooking compartment.

4. Run a manual steam generator rinse cycle. To Empty and Rinse the Steam Generator: a. Press the Smart Key. b. Select “Manual Steam Generator Rinse” with the

Selector Dial. c. Confirm “Yes” with the Smart Key. d. Steam generator rinses and begins to refill to

operating level.

4. Remove the cap from the descale port located at the top of the Combi (See Figure 6-1).

5. While the steam generator is filling with water, use a funnel (NOT INCLUDED) to add 3/4 gallon of DISSOLVE Combis, and 1/2 gallon for all other models

Death, injury, equipment and property damage can result.

This procedure is slightly different depending on the model

being descaled. This entire procedure should be read and fully

understand as it applies to the model being descaled, before

Do NOT heat the Combi during descaling.

inning the actual descaling operation.

be

® descaler solution into the descaling port of 20.20

WARNING

.

Figure 6-1

Descaling Port

Located at Right Rear of the Combi

•

27

While adding liquid to the steam generator through the descaler inlets, pour slowly to avoid overflow.

•

Wipe up any spills at once to avoid etching.

6. After the automatic fill cycle has ended, turn OFF the Combi with the ON/OFF key, and at the Control Power Service Disconnect switch located below the hand shower. See Figure 6-2.

7. Add cold tap water through the descale port until descaling solution enters the cooking compartment through the steam port or until the descaling port overflows (water required varies depending on the Model).

• Wipe up any spills and overflows.

8. Let the Descaler work for 1 hour.

9. Turn the Combi ON at the Control Power Service Disconnect switch located below the hand shower. See Figure 6-2.

10. Turn ON the Combi with the ON/OFF key.

11. Run a manual steam generator rinse cycle (Step 4).

12. After the automatic fill cycle has ended, turn OFF the Combi with ON/OFF key, and at the Control Power Service Disconnect switch located below the hand shower. See Figure 6-

2.

13. Add water through the descale port until water enters the cooking compartment through the steam port or until the descaling port overflows (water required varies depending on the Model) to rinse descaler from the area above the normal water fill level.

14. Replace the descale port cap.

15. Turn the Combi ON at the Control Power Service Disconnect switch located below the hand shower. See Figure 6-2.

16. Turn ON the Combi with the ON/OFF key.

17. After the Automatic Fill ends, run a manual steam generator rinse cycle (See Step 4).

18. Run Combi mode for 30 minutes at 212° F with Crisp & Tasty function.

19. Close the cooking compartment door. a. Press Combi key. b. Press Temperature key. c. Set temperature with Selector Dial to 212° F. d. Press Time key. e. Set time with the Selector Dial for 30 minutes. f. Press Smart Key Various options appear in the display. g. Select “Crisp & Tasty” with the Selector Dial. h. Select the Crisp & Tasty level to “high demoisturizing – continuous” with the Selector

Dial.

i. Confirm “Yes” with Smart Key. j. The Crisp & Tasty icon

k. Press the Start/Stop key to start. l. Signal Tone sounds and steaming stops after 30 minutes. m. Press the Start/Stop key to end the Signal Tone.

20. Run a manual steam generator rinse cycle. (See Step 4) This is the final rinse. The Combi is now ready for normal operation.

appears in the display.

48

51

61

23 47 50 1864

58

14

2

1

41

54

12

13

46

42

6

25

20

66

11

30

39

26

53

49

52 5

3

67

65

45

10

15

24

4

63

9

27

29

40

28

60

8

62

7

59

33

31

32

57

38

37

35

36

39

34

56

17

43

55

22

19

21

44

16

1010 GAS GENERATOR W CLEANING

28

Washer Arm C2611068

Light C5005043 Light Gasket C6015020

Condensate Box o-ring C6015000

Spray Handle Shut Off Valve C6014003 Spray Handle Bracket C2002042

C6015028 Burner Chamber Seal C6015027 Flue Seal

C3216313 B

0706

1010 GAS GENERATOR W CLEANING

29

C6012001

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2115483 ASSEMBLY, PANEL, RIGHT SIDE, 10.10 2 1 C2114824 ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.10/10.10 3 1 C2115490 ASSEMBLY, CORNER, FRONT, RIGHT, 10.10/10.20 4 1 C2114452 WELDMENT, FACE PLATE, LOWER, 6.10/10.10 5 1 C2114719 WELDMENT, REINFORCEMENT, DOOR LATCH, 10.10/10.20 6 1 C2114688 ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, 6.10/10.10 7 1 C2114743 ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 10.10 8 1 C2114783 ASSEMBLY, PANEL, LEFT SIDE, 10.10 9 1 C2115375 WELDMENT, CHANNEL, FRONT, 6.10/10.10 10 1 C2115443 FRONT PIECE, PRE-MOUNTED, 10.10 11 1 C6010001 WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304

12 1 C22141901 PAN RACK,LEFT, ELECTROPOLISHED, 10.10 13 1 C2214191 WELDMENT, PAN RACK, RIGHT, 10.10 14 1 C2614841 CAVITY LIGHT 15 1 C7011002 DOOR SEAL, 10.10 16 1 C2614802 ASSEMBLY, SLIDING PLATE VST 10.10/10.20 17 1 C2013006 WELDMENT, HINGE CARRIER, UPPER, DOOR 18 1 C2614740 ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL 19 1 C26142661 ASSEMBLY, CONTROLLER 20 1 C2614263 ASSEMBLY, CORE TEMPERATURE SENSOR 21 1 C2514352 ASSEMBLY, DOOR 10.10 22 1 C2216070 ASSEMBLED, BLOCK 23 1 C2608962 ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT 24 1 C22160801 ASSEMBLY, HAND SHOWER, 10.10, 6.10 25 1 C2114731 FACEPLATE, UPPER X.10 26 1 C2114634 CORNER, WELDED, REAR, LEFT, 10.10/10.20 27 1 111544 WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,

28 1 111543 RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL,

29 1 111542 WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,

30 1 111540 NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL 31 4 C8006060 SCHNORR LOCK WASHER 32 4 C8005050 WASHER, 8.4 A2 DIN 125 33 4 C8004057 NUT, HEX, M8 A4 34 4 C6015213 SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in) 35 1 C6015210 SHIM, WEARING MOTOR SHAFT SEAL 36 1 C6015206 BUSHING, LABYRINTH 37 1 C6015050 SPRING, MOTOR SHAFT SEAL 38 1 C2114140 MOTOR MOUNTING PLATE 39 2 C6015021 SEALING RING, MOTOR SHAFT, VITON, COMBI 40 1 111541 NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL 41 1 C6012009 GUIDE STRIP, LOWER VST 42 4 C6012011 DOORSTOPPER VA VST 43 1 C2114817 COVER PANEL VST 10.10/10.20 44 1 C6012008 SUPPORT STRIP RST 45 1 19993 SWITCH, ROCKER, DPDT, ON/OFF 15A, 125V 46 1 C2017001 SAFETY RAIL VST 6.10/10.10 47 1 C6005427 DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE 48 1 C6005048 DIAPHRAGM GROMMET ø 60 mm (DG 48) 49 1 C2414125 FINAL ASSEMBLY, CONDENSER 50 1 109641 PORT ASSY, DESCALER 51 1 C2114287 ASSEMBLY, AIR OUTLET 52 1 C5001041 SAFETY TEMPERATURE LIMITER, 340ºC 53 1 C2114798 BRACKET, HIGH LIMIT, STEAM GENERATOR 54 1 C2214143 ASSEMBLY, INTAKE PANEL, GEN, 10.10, 55 1 C2114296 ASSY, CONTROL PANEL, STEAM GEN, WITH PICTO 56 1 300480 ASSY., COMP. PANEL, OGB 6.20/10.10 57 1 C50180211 MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW,

58 1 C2215042 WELDMENT, INNER HOUSING, GAS, GEN, 10.10, REI 59 1 C2314882 STEAM GENERATOR, GAS, 10.10, PREASSEMBLED 60 1 C2010000 WELDMENT, HEAT EXCHANGER, GAS, 10.10/20.10 61 1 C2614862 BURNER INSERT,10.10/20.10, HOT AIR, NAT GAS 62 1 C2314900 ASSEMBLY, BURNER INSERT, GEN, GAS, 6.20/10.10, NAT 63 1 C2114545 BASE, GAS, GEN, 10.10 W/CLEANING 64 1 C2115463 ASSEMBLY, PANEL, TOP, GAS GEN, 10.10 65 1 C2018000 DRIP TRAY, 10.10 66 1 C2016009 COVER, BYPASS 67 1 C2216796 ASSEMBLY, COVER, DEHUMIDIFYING GUTTER

6.20 & 10.10 COMBI

10.21mm ID X 24mm OD X 1.85mm THICK

WALDES #5100-25H

8.4mm ID X 13mm OD X 0.8mm THICK

GAS COMBI

C3216313 B

0706

51

12

1755

26 50 59 21

1 49

45 6

44 16

13 14

20

46

47

19

2

28

23

61

11

33

42

30

32

43

31

57

8

27

24

22

25

15

28

52 62

7

18

60

48 10

9

36

34

35

53

41

40

38

39

42

37

58

54

5

4

3

1010 GAS INJ W CLEANING

30

Washer Arm C2611068

Light Gasket C6015020

Lamp C5005043

Condensate Box o-ring C6015000

Spray Handle Bracket C2002042

Spray Handle Shut Off Valve C6014003

C3216313 B

0706

1010 GAS INJ W CLEANING

31

C6012001

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2115483 ASSEMBLY, PANEL, RIGHT SIDE, 10.10 2 1 C2114824 ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.10/10.10 3 1 C2115490 ASSEMBLY, CORNER, FRONT, RIGHT, 10.10/10.20 4 1 C2114452 WELDMENT, FACE PLATE, LOWER, 6.10/10.10 5 1 C2114719 WELDMENT, REINFORCEMENT, DOOR LATCH, 10.10/10.20 6 1 C2114688 ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, 6.10/10.10 7 1 C2114743 ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 10.10 8 1 C2114783 ASSEMBLY, PANEL, LEFT SIDE, 10.10 9 1 C2115375 WELDMENT, CHANNEL, FRONT, 6.10/10.10 10 1 C2115443 FRONT PIECE, PRE-MOUNTED, 10.10 11 1 C6010001 WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304 SST,

12 1 C2114292 AIR OUTLET CONECTING PIECE 20.20 GEN. 6.20/10.10/20.20 INJ. 13 1 C22141901 PAN RACK,LEFT, ELECTROPOLISHED, 10.10 14 1 C2214191 WELDMENT, PAN RACK, RIGHT, 10.10 15 1 C2114296-3 ASSY, CONTROL PANEL, SPRITZER, WITH PICTO 16 1 C2214153 ASSEMBLY, INTAKE PANEL INJ 10.10 17 1 C2614841 CAVITY LIGHT 18 1 C7011002 DOOR SEAL, 10.10 19 1 C2614802 ASSEMBLY, SLIDING PLATE VST 10.10/10.20 20 1 C2013006 WELDMENT, HINGE CARRIER, UPPER, DOOR 21 1 C2614740 ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL 22 1 C26142661 ASSEMBLY, CONTROLLER 23 1 C2614263 ASSEMBLY, CORE TEMPERATURE SENSOR 24 1 C2514352 ASSEMBLY, DOOR 10.10 25 1 C2216070 ASSEMBLED, BLOCK 26 1 C2608962 ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT 27 1 C22160801 ASSEMBLY, HAND SHOWER, 10.10, 6.10 28 1 C2114731 FACEPLATE, UPPER X.10 29 1 C2114634 CORNER, WELDED, REAR, LEFT, 10.10/10.20 30 1 111544 WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,

31 1 111543 RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL,

32 1 111542 WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,

33 1 111540 NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL 34 4 C8006060 SCHNORR LOCK WASHER 35 4 C8005050 WASHER, 8.4 A2 DIN 125 36 4 C8004057 NUT, HEX, M8 A4 37 4 C6015213 SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in) 38 1 C6015210 SHIM, WEARING MOTOR SHAFT SEAL 39 1 C6015206 BUSHING, LABYRINTH 40 1 C6015050 SPRING, MOTOR SHAFT SEAL 41 1 C2114140 MOTOR MOUNTING PLATE 42 2 C6015021 SEALING RING, MOTOR SHAFT, VITON, COMBI 43 1 111541 NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL 44 1 C6012009 GUIDE STRIP, LOWER VST 45 4 C6012011 DOORSTOPPER VA VST 46 1 C2114817 COVER PANEL VST 10.10/10.20 47 1 C6012008 SUPPORT STRIP RST 48 1 19993 SWITCH, ROCKER, DPDT, ON/OFF 15A, 125V 49 1 C2017001 SAFETY RAIL VST 6.10/10.10 50 1 C6005427 DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE 51 1 C6005048 DIAPHRAGM GROMMET ø 60 mm (DG 48) 52 1 C2414125 FINAL ASSEMBLY, CONDENSER 53 1 C50180211 MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW,

54 1 C2114535 BASE, GAS, INJ, 10.10 W/CLEANING 55 1 C2215041 WELDMENT, INNER HOUSING, GAS, INJ, 10.10, REI 56 1 C2614862 BURNER INSERT,10.10/20.10, HOT AIR, NAT GAS 57 1 C2010000 WELDMENT, HEAT EXCHANGER, GAS, 10.10/20.10 58 1 300488 ASSY., COMP. PANEL, OGS 6.20/10.10 59 1 C2115453 ASSEMBLY, TOP PANEL, GAS INJ, 10.10 60 1 C2018000 DRIP TRAY, 10.10 61 1 C2016009 COVER, BYPASS 62 1 C2216796 ASSEMBLY, COVER, DEHUMIDIFYING GUTTER

6.20 & 10.10 COMBI

10.21mm ID X 24mm OD X 1.85mm THICK

WALDES #5100-25H

8.4mm ID X 13mm OD X 0.8mm THICK

GAS COMBI

C3216313 B

0706

47 48 22 59 54 15

60

17

1

26

28

5

2

27 64 11 12

53

6

5658

57

51

40

38

39

50

44

41

46

45

55

2043

42

23

19

63

33

35

34

46

21

37

36

9825

52

13

49 7

18

29

24

30 32

22

3

61

65

4

14

10

31

16

62

620 GAS GEN W CLEANING

32

Washer Arm C2611068

Light Gasket C6015020

Lamp C5005043

Set of racks with center support FK1119821

Condensate Box o-ring C6015000

Spray Handle Bracket C2002042

Spray Handle Shut Off Valve C6014003

C3216313 B

0706

620 GAS GEN W CLEANING

33

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2115482 ASSEMBLY, PANEL, RIGHT SIDE, 6.20 2 1 C2114826 ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.20/10.20 3 1 C2115489 ASSEMBLY, CORNER, FRONT, RIGHT, 6.20 4 1 C2114453 WELDMENT, FACEPLATE, LOWER, 6.20/10.20 5 1 C2114690 ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, X.20 6 1 C2114782 ASSEMBLY, PANEL, LEFT SIDE, 6.20 7 1 C2514351 DOOR 6.20 COMPLETE 8 1 C2614801 SLIDING PLATE VST 6.20 COMPLETE 9 1 C2013006 WELDMENT, HINGE CARRIER, UPPER, DOOR 10 1 C2115442 ASSEMBLY, CORNER, FRONT LEFT, 6.20 11 1 C22141881 PAN RACKS,LEFT, ELECTROPOLISHED, 6.20 11 1 C22141891 PAN RACKS,RIGHT, ELECTROPOLISHED, 6.20 13 1 C7011004 DOOR SEAL, 6.20 14 1 C2216080 ASSEMBLY, HAND SHOWER 15 1 C2614740 ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL 16 1 C6012001 ASSEMBLY, BLOCK 17 1 C2614841 CAVITY LIGHT 18 1 C26142661 ASSEMBLY, CONTROLLER 19 1 C2614263 ASSEMBLY, CORE TEMPERATURE SENSOR 20 1 C2414125 FINAL ASSEMBLY, CONDENSER 21 1 C6010001 WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304 SST, 6.20 & 10.10 COMBI 22 1 C2608962 ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT 23 1 C2114732 FACEPLATE, UPPER X.20 24 1 C2114633 CORNER, WELDED, REAR, LEFT, 6.20 25 1 C6012008 SUPPORT STRIP RST 26 1 C2017000 SAFETY RAIL, VST, X.20 27 1 C6012009 GUIDE STRIP, LOWER VST 28 4 C6012011 DOORSTOPPER VA VST 29 1 C2114816 COVER PANEL, DISAPPEARING DOOR RST 6.20 30 1 C2114798 BRACKET, HIGH LIMIT, STEAM GENERATOR 31 1 C5001041 SAFETY TEMPERATURE LIMITER, 340ºC 33 1 111544 WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,

34 1 111543 RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL, WALDES #5100-25H 35 1 111542 WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,

36 1 111541 NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL 37 1 111540 NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL 38 4 C8006060 SCHNORR LOCK WASHER 39 4 C8005050 WASHER, 8.4 A2 DIN 125 40 4 C8004057 NUT, HEX, M8 A4 41 1 C6015210 SHIM, WEARING MOTOR SHAFT SEAL 42 1 C6015206 BUSHING, LABYRINTH 43 1 C6015050 SPRING, MOTOR SHAFT SEAL 44 1 C2114140 MOTOR MOUNTING PLATE 45 4 C6015213 SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in) 46 2 C6015021 SEALING RING, MOTOR SHAFT, VITON, COMBI 47 1 C6005048 DIAPHRAGM GROMMET ø 60 mm (DG 48) 48 1 C6005427 DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE 49 1 C2018001 DRIP TRAY, DOOR 50 1 C50180211 MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW, GAS COMBI 51 1 C2614860 BURNER INSERT, 6.20, AIR, COMPLETE, NAT GAS 52 1 C2010032 HEAT EXCHANGER 6.20 WELDED 53 1 C2114742 ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 6.20 54 1 C2115462 ASSEMBLY, TOP PANEL, GAS GEN, 6.20 55 1 300480 ASSY., COMP. PANEL, OGB 6.20/10.10 56 1 C2114287 ASSEMBLY, AIR OUTLET, 57 1 C2314900 ASSEMBLY, BURNER INSERT, GEN, GAS, 6.20/10.10, NAT 58 1 C2314881 ASSEMBLY, STEAM GENERATOR, GAS 6.20 59 1 109641 PORT ASSY, DESCALER 60 1 C2215026 ASSEMBLY, INNER HOUSING, 6.20, GAS, STEAM GEN, REI, KTM 61 1 C21145471 BASE, 6.20 GAS GEN, W/CLEAN 62 1 C2114296 ASSY, CONTROL PANEL, STEAM GEN, WITH PICTO 63 1 C2016009 COVER, BYPASS 64 1 C2214142 INTAKE PANEL STEAM GENERATOR 6.20, COMPLETE 65 1 C2114718 ASSEMBLY, REINFORCEMENT, DOOR LATCH, 6.20

10.21mm ID X 24mm OD X 1.85mm THICK

8 x4mm ID X 13mm OD X 0.8mm THICK

C3216313 B

0706

49 50 24 17

55

19

1

28

30

5

2

29 53 13 14

6

7

60

57

42

40

41

56

46

43

48

47

54

2245

44

25

21

61

35

37

36

48

23

39

38

111027

58

15

51 9

20

31

26

32 34

22

3

59

62

4

16

12

33

18

52

620 GAS INJ W CLEANING

34

Washer Arm C2611068

Light gasket C6015020

Lamp C5005043

Set of racks with center support FK1119821

Condensate Box o-ring C6015000

Spray Handle Bracket C2002042

Spray Handle Shut Off Valve C6014003

C3216313 B

0706

620 GAS INJ W CLEANING

35

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2115482 ASSEMBLY, PANEL, RIGHT SIDE, 6.20 2 1 C2114826 ASSEMBLY/WELDMENT, INTERMEDIATE TOP, 6.20/10.20 3 1 C2115489 ASSEMBLY, CORNER, FRONT, RIGHT, 6.20 4 1 C2114453 WELDMENT, FACEPLATE, LOWER, 6.20/10.20 5 1 C2114690 ASSEMBLY, SLIDE BAR, DISAPPEARING DOOR, X.20 6 1 C2114742 ASSEMBLY, PANEL, REAR, ELECTRIC & GAS INJ, 6.20 7 1 C2114782 ASSEMBLY, PANEL, LEFT SIDE, 6.20 8 1 C2115452 ASSEMBLY, TOP PANEL, GAS INJ, 6.20 9 1 C2514351 DOOR 6.20 COMPLETE 10 1 C2614801 SLIDING PLATE VST 6.20 COMPLETE 11 1 C2013006 WELDMENT, HINGE CARRIER, UPPER, DOOR 12 1 C2115442 ASSEMBLY, CORNER, FRONT LEFT, 6.20 13 1 C22141881 PAN RACKS,LEFT, ELECTROPOLISHED, 6.20 14 1 C22141891 PAN RACKS,RIGHT, ELECTROPOLISHED, 6.20 15 1 C7011004 DOOR SEAL, 6.20, 16 1 C2216080 ASSEMBLY, HAND SHOWER 17 1 C2614740 ASSEMBLY, GUIDE CLIP, VST, COUNTERTOP MODEL 18 1 C6012001 ASSEMBLY, BLOCK 19 1 C2614841 CAVITY LIGHT 20 1 C26142661 ASSEMBLY, CONTROLLER 21 1 C2614263 ASSEMBLY, CORE TEMPERATURE SENSOR 22 1 C2414125 FINAL ASSEMBLY, CONDENSER 23 1 C6010001 WHEEL, BLOWER, 350mm OD X 110mm WIDE, TYPE 304 SST, 6.20 & 10.10 COMBI 24 1 C2608962 ASSEMBLY, NEGATIVE PRESSURE SAFETY VENT 25 1 C2114732 FACEPLATE, UPPER X.20 26 1 C2114633 CORNER, WELDED, REAR, LEFT, 6.20 27 1 C6012008 SUPPORT STRIP RST 28 1 C2017000 SAFETY RAIL, VST, X.20 29 1 C6012009 GUIDE STRIP, LOWER VST 30 4 C6012011 DOORSTOPPER VA VST 31 1 C2114816 COVER PANEL, DISAPPEARING DOOR RST 6.20 32 1 C2114798 BRACKET, HIGH LIMIT, STEAM GENERATOR 33 1 19993 SWITCH, ROCKER, DPDT, ON/OFF 15A, 125V 34 1 C5001041 SAFETY TEMPERATURE LIMITER, 340ºC 35 1 111544 WASHER, BELLEVILLE, M10, SMOOTH, TYPE 301 SST,

36 1 111543 RING, RETAINING, EXTERNAL, 1/4", STAINLESS STEEL, WALDES #5100-25H 37 1 111542 WASHER, BELLEVILLE, M8, SERRATED BOTH SIDES, SST,

38 1 111541 NUT, HEX, LEFT-HAND, M8 X 1.25 (DIN 934L), STAINLESS STEEL 39 1 111540 NUT, HEX, M10 X 1.5 (DIN 934), STAINLESS STEEL 40 4 C8006060 SCHNORR LOCK WASHER 41 4 C8005050 WASHER, 8.4 A2 DIN 125 42 4 C8004057 NUT, HEX, M8 A4 43 1 C6015210 SHIM, WEARING MOTOR SHAFT SEAL 44 1 C6015206 BUSHING, LABYRINTH 45 1 C6015050 SPRING, MOTOR SHAFT SEAL 46 1 C2114140 MOTOR MOUNTING PLATE 47 4 C6015213 SPACER, MOTOR 1.299 (FAN DISTANCE 2.008in) 48 2 C6015021 SEALING RING, MOTOR SHAFT, VITON, COMBI 49 1 C6005048 DIAPHRAGM GROMMET ø 60 mm (DG 48) P2 50 1 C6005427 DIAPHRAGM GROMMET ø 83 (DG60) FOR VAC. REG. VALVE 51 1 C2018001 DRIP TRAY, DOOR 52 1 C2114296-3 ASSY, CONTROL PANEL, SPRITZER, WITH PICTO 53 1 C2214152 ASSEMBLY, INTAKE PLATE, IN, 6.20 54 1 300488 ASSY., COMP. PANEL, OGS 6.20/10.10 55 1 C2215025 ASSEMBLY, INNER SHELL 6.20, GAS, IN, REI, KTM 56 1 C50180211 MOTOR W/STUD, ALL VOLTAGES, 3-PHASE, 4 POLE, 0.6KW, GAS COMBI 57 1 C2614860 BURNER INSERT, 6.20, AIR, COMPLETE, NAT GAS 58 1 C2010032 HEAT EXCHANGER 6.20 WELDED 59 1 C2114537 BASE, GAS, INJ, 6.20, W/ CLEANING 60 1 C2114292 AIR OUTLET CONECTING PIECE 20.20 GEN. 6.20/10.10/20.20INJ. 61 1 C2016009 COVER, BYPASS 62 1 C2114718 ASSEMBLY, REINFORCEMENT, DOOR LATCH, 6.20

10.21mm ID X 24mm OD X 1.85mm THICK

8.4mm ID X 13mm OD X 0.8mm THICK

C3216313 B

0706

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

TOLERANCES

(UNLESS OTHERWISE

NOTED)

DO NOT SCALE

PRINTED DRAWING

DRAWN BY DATE

TITLE

DRAWING NO.

SIZE

ANGULAR

DECIMAL

0.03

1

~

`

ASSY., COMP. PANEL, OGB 6.20/10.10

D

1 2

300419

TRANSFORMER, 24V

2 1

111603 DIN RAIL 3.25"

3

2

111601 DIN RAIL 8.375"

4

1

111526

PLATE, ADAPTER, A.C. DRIVE

5

1

300412

AC DRIVE (6.20-10.10)

6

1

300413

LINE FILTER, 10A

7

4

C8009043

M4 HEX STAND OFF, 70 MM

8

1

C5116110

BRACKET, TERMINAL BLOCK, COMPONENT PANEL

9

5

C4014012

TERMINAL BLOCK, SPRING-LOADED, FOUR-WIRE, BLUE

10

4

C4014006

TERMINAL BLOCK, CONDUCTOR, SPRING-LOADED

11

3

C4014037

DINRAIL MOUNTED FUSEHOLDER (6.3X32)

12

3

C4014011

COVER, FOUR-WIRE

13

1

300350

POWER SUPPLY (12V)

14

5

C4014030

TERMINAL BLOCK, SPRING LOADED, 1.5MM2

15

2

C4014031 COVER 2.5 MM2

16

14

C8001024

SCREW, FILISTER HD, M4x10 DIN 7985

17

6 111605

M4 NUT

18

14

111606

M4 LOCK WASHER

19 6

C4014000 SNAP-ON END BRACKET

20

2

C4014013

TERMINAL BLOCK, SPRING- LOADED, FOUR-WIRE

21

8

C4014010

TERMINAL, SPRING LOADED, FOUR WIRE, 2.5 MM2

22 2

C4014009

TERMINAL BLOCK, SPRING LOADED, 1.5 MM2, BLUE

23

1

C4014008 COVER FOUR-WIRE 2.5 MM2

24 1

C4014024

TERMINAL, FEED THROUGH, 4 MM2

25

1

C4014016

TERMINAL, GROUNDED, SPRING LOADED, 2.5 MM2

26

1

C4014023

TERMINAL, FEED THROUGH,4MM2, BLUE

27 1

C4014020 COVER 4 MM2

28

1

300418

FUSE MDA-1

29

1

300416

FUSE MDA-2

30

1

KE52936-9

FUSE, MDA-15

32

5

C4014033

LABEL BLANK, TERMINAL BLOCK, ZB4

33

14

C4014044

LABEL, BLANK, TERMINAL BLOCK, ZB6

34 10

C4014032

SERRATED COVER STRIP,PLAIN ZB5

35 6

C4014039

LABEL BLANK, TERMINAL BLOCK, ZBF6

36

4

C4014001

JUMPER, 2 PIN

37

2

C4014002

JUMPER 2-PIN

38

1

C5115400

PANEL, ELECTRICAL COMPONENT 6.10/6.20/10.10

40 6 106123

SCREW, 10-32 X 1/2, TORX/ PAN HD, THRD FORMING, ZN

41 2

20323

RING TO MALE TAB TERMINAL

42

4

C8003095

HEXAGON BOLT, M5x16, A2 HUD 20.20

43

4

C8004030

HEXAGON NUT, M5, A2, P2, P3

44 4

C8006030

RING, SPRING RETAINER, B5, A2

45

1

C700106606 EDGE GUARD

000

46

1

300483

WIRE HARNESS, 6.20/10.10

47

1

300501

WIRE HARNESS, POWER, OGB/OGS 6.20/10.10

48

4

20370

TERM.,FULL INSUL, MALE, 0.250 TAB

49

4

300231

TERM., FULL INSUL, FEMALE, 0.250 TAB

57

2

111751

BUSHING, UNIVERSAL,1.5DIA HOLE,HEYCO#2213,SNAP-IN UL

58

4

106127

SCREW, 6-32 X 1/2, TORX/PAN HD

ITEM

QTY

PART N0.

NOT SHOWN

29

28

30

36

33

37

32

19

3

19

24

26

25

27

19

16

19

35

11

9

12

10

12

14

15 14

15

18

17

8

38

33

41

48

18

16

40

44

43

4

7

17

18

6

16

2

42

5

49

1

49

45

40

3

19

13

33

20

12

21

34

22

21

22

23

1

36

COMPONENT PANEL ASSEMBLY, Gas

OGB 6.20 & 10.10 MODELS

300480 C

0706

COMPONENT PANEL ASSEMBLY, GAS

37

OGB 6.20 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 2 300419 TRANSFORMER, 24V 2 1 111603 DIN RAIL 3.25" 3 2 111601 DIN RAIL 8.375" 4 1 111526 PLATE, ADAPTER, A.C. DRIVE 5 1 300412 AC DRIVE (6.20-10.10) 6 1 300413 LINE FILTER, 10A 7 4 C8009043 M4 HEX STAND OFF, 70 MM 8 1 C5116110 BRACKET, TERMINAL BLOCK, COMPONENT PANEL 9 5 C4014012 TERMINAL BLOCK, SPRING-LOADED, FOUR-WIRE, BLUE 10 4 C4014006 TERMINAL BLOCK, CONDUCTOR, SPRING-LOADED 11 3 C4014037 DINRAIL MOUNTED FUSEHOLDER (6.3X32) 12 3 C4014011 COVER, FOUR-WIRE 13 1 300350 POWER SUPPLY (12V) 14 5 C4014030 TERMINAL BLOCK, SPRING LOADED, 1.5MM2 15 2 C4014031 COVER 2.5 MM2 16 14 C8001024 SCREW, FILISTER HD, M4x10 DIN 7985 17 6 111605 M4 NUT 18 14 111606 M4 LOCK WASHER 19 6 C4014000 SNAP-ON END BRACKET 20 2 C4014013 TERMINAL BLOCK, SPRING- LOADED, FOUR-WIRE 21 8 C4014010 TERMINAL, SPRING LOADED, FOUR WIRE, 2.5 MM2 22 2 C4014009 TERMINAL BLOCK, SPRING LOADED, 1.5 MM2, BLUE 23 1 C4014008 COVER FOUR-WIRE 2.5 MM2 24 1 C4014024 TERMINAL, FEED THROUGH, 4 MM2 25 1 C4014016 TERMINAL, GROUNDED, SPRING LOADED, 2.5 MM2 26 1 C4014023 TERMINAL, FEED THROUGH,4MM2, BLUE 27 1 C4014020 COVER 4 MM2 28 1 300418 FUSE MDA-1 29 1 300416 FUSE MDA-2 30 1 KE52936-9 FUSE, MDA-15 32 5 C4014033 LABEL BLANK, TERMINAL BLOCK, ZB4 33 14 C4014044 LABEL, BLANK, TERMINAL BLOCK, ZB6 34 10 C4014032 SERRATED COVER STRIP,PLAIN ZB5 35 6 C4014039 LABEL BLANK, TERMINAL BLOCK, ZBF6 36 4 C4014001 JUMPER, 2 PIN 37 2 C4014002 JUMPER 2-PIN 38 1 C5115400 PANEL, ELECTRICAL COMPONENT 6.10/6.20/10.10 40 6 106123 SCREW, 10-32 X 1/2, TORX/ PAN HD, THRD FORMING, ZN 41 2 20323 RING TO MALE TAB TERMINAL 42 4 C8003095 HEXAGON BOLT, M5x16, A2 HUD 20.20 43 4 C8004030 HEXAGON NUT, M5 44 4 C8006030 RING, SPRING RETAINER, B5, A2 45 1 C700106606000 EDGE GUARD

46 1 300483 WIRE HARNESS, 6.20/10.10 47 1 300501 WIRE HARNESS, POWER, OGB/OGS 6.20/10.10 48 4 20370 TERM., FULL INSUL, MALE, 0.250 TAB 49 4 300231 TERM., FULL INSUL, FEMALE, 0.250 TAB 57 2 111751 BUSHING, UNIVERSAL,1.5DIA HOLE,HEYCO#2213,SNAP-IN UL 58 4 106127 SCREW, 6-32 X 1/2, TORX/PAN HD

300480 C

0706

COMPONENT PANEL ASSEMBLY, GAS

NOT SHOWN

45

39

40

3

19

13

33

29

28

30

33

36

33

32

19

20

12

37

21

34

22

21

22

23

19

3

19

24

26

25

27

19

16

19

35

11

9

12

10

12

14

15 14

15

18

17

39

8

38

33

41

48

18

16

31

40

44

43

4

7

17

18

6

16

2

18

17

1

425

49

38

OGS 6.20 & 10.10 MODELS

300488 C

0706

COMPONENT PANEL ASSEMBLY, GAS

39

OGS 6.20 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 300419 TRANSFORMER, 24V 2 1 111603 DIN RAIL 3.25" 3 2 111601 DIN RAIL 8.375" 4 1 111526 PLATE, ADAPTER, A.C. DRIVE (NOT SHOWN) 5 1 300412 AC DRIVE (6.20-10.10) (NOT SHOWN) 6 1 300413 LINE FILTER, 10A 7 4 C8009043 M4 HEX STAND OFF, 70 MM 8 1 C5116110 BRACKET, TERMINAL BLOCK, COMPONENT 9 5 C4014012 TERMINAL BLOCK, SPRING-LOADED, FOUR-WIRE, BLUE 10 4 C4014006 TERMINAL BLOCK, CONDUCTOR, SPRING-LOADED 11 3 C4014037 DINRAIL MOUNTED FUSEHOLDER (6.3X32) 12 3 C4014011 COVER, FOUR-WIRE 13 1 300350 POWER SUPPLY (12V) 14 5 C4014030 TERMINAL BLOCK, SPRING LOADED, 1.5MM2 15 2 C4014031 COVER 2.5 MM2 16 10 C8001024 SCREW, FILISTER HD, M4x10 DIN 7985 17 8 111605 M4 NUT 18 12 111606 M4 LOCK WASHER 19 6 C4014000 SNAP-ON END BRACKET 20 2 C4014013 TERMINAL BLOCK, SPRING- LOADED, FOUR-WIRE 21 8 C4014010 TERMINAL, SPRING LOADED, FOUR WIRE, 2.5 22 2 C4014009 TERMINAL BLOCK, SPRING LOADED, 1.5 MM2, 23 1 C4014008 COVER FOUR-WIRE 2.5 MM2 24 1 C4014024 TERMINAL, FEED THROUGH, 4 MM2 25 1 C4014016 TERMINAL, GROUNDED, SPRING LOADED, 2.5 MM2 26 1 C4014023 TERMINAL, FEED THROUGH,4MM2, BLUE 27 1 C4014020 COVER 4 MM2 28 1 300418 FUSE MDA-1 29 1 300416 FUSE MDA-2 30 1 KE52936-9 FUSE, MDA-15 31 2 111751 BUSHING, UNIVERSAL,1.5DIA HOLE,HEYCO# 2213, SNAP-IN UL 32 5 C4014033 LABEL BLANK, TERMINAL BLOCK, ZB4 33 14 C4014044 LABEL, BLANK, TERMINAL BLOCK, ZB6 34 10 C4014032 SERRATED COVER STRIP,PLAIN ZB5 35 6 C4014039 LABEL BLANK, TERMINAL BLOCK, ZBF6 36 4 C4014001 JUMPER, 2 PIN 37 2 C4014002 JUMPER 2-PIN 38 1 C5115400 PANEL, ELECTRICAL COMPONENT 6.10/6.20/10.10 39 6 C8001022 STUD, WELD, M4 X 6, CD, SST 40 6 106123 SCREW, 10-32 X 1/2, TORX/ PAN HD, THRD FORMING, ZN 41 2 20323 RING TO MALE TAB TERMINAL 42 4 C8003095 HEXAGON BOLT, M5x16, A2 HUD 20.20 43 4 C8004030 HEXAGON NUT, M5 44 4 C8006030 RING, SPRING RETAINER, B5, A2 45 1 C700106606000 EDGE GUARD 46 1 300490 WIRE HARNESS,OGS, 6.20/10.10 47 1 300501 WIRE HARNESS, POWER, OGB/OGS 6.20/10.10 48 2 20370 TERM.,FULL INSUL, MALE, 0.250 TAB 49 2 300231 TERM., FULL INSUL, FEMALE, 0.250 TAB

300488 C

0706

11

5

2

4

10

9

1

7

6

3

8

ASSEMBLY, CONTROL PANEL, WITH PICTO

40

ALL MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2114297 WELDMENT, CONTROL PANEL 2 1 C5019101 CONTROLLER, 5010 OPERATING MODULE 3 1 C5019105 CONTROLLER, 5010 PICTOMODULE PICTO 4 1 C5009313 LATCH ROCKER 5 1 C5009314 KNOB, SELECTOR, COMBI 6 10 C8009030 SPACER, CONTROL PANEL 7 1 C7011010 GASKET, FRONT PLATE 8 10 C6005254 NUT, KNURLED 9 1 111588 LABEL, CONTROL PANEL, STEAM GEN, WITH PICTO

1 111590 LABEL, CONTROL PANEL, SPRITZER, WITH PICTO 10 2 C6005270 SPACER, CONTROL KNOB STOP 11 2 C8007013 SLOTTED PAN-HEAD TAPPING SCREW 2.2 X 13 12 1 300533 CABLE, CONNECTING, CONTROL (NOT SHOWN)

C2114296 B & C2114296-3 B

0706

32

1

C5016002 LOCKNUT M25 P3

3

1

C700106607

EDGE PROTECTOR, CUT 7.000"

0

00-1

30

1

C700106607

EDGE PROTECTOR, CUT 7.000"

000

2

21

C2010066

CONNECTION, GAS, SINGLE 3/4" P3

20

1

C5016001

FITTING, ELECTRICAL, LIQUID TIGHT

19

1

C2016147

CONDENSER HOSE ASSY, GAS

18

1

C2016130

ASSY, WATER VA LVE, GAS, 10.10

17 1

C2616452

BOTTOM FLAP, PUMP HOUSING GAS 10.10 110V PREASSEMBLED

16

1

C5215897

CABLE HARNESS, ILLUMINATION

15

5

C8005021

WASHER, 4.3, DIN 125

14

7

C8013004 HEXAGON BOLT M4 X 10 A2 P3

13 3

C8003029

MLF, SCREW, M5x10 A2 P2 P3

12 1

111551

TRAY, DRIP, FA N, REAR, ELECTRIC & GAS INJ, 6.10/10.10 P3

11 1

111522

TRAY, DRIP, FA N, FRONT, 6.20/20.20/10.10

NOT SHOWN

17

2

15

4

8

9

19

22

1

8

1

12

6

10

14

1

5

3

11

5

13

1

20

BASE, GAS,

41

Pressure Switch C5009055 Agent Pump 300352

INJECTOR, WITH CLEANING

OGS 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

32 1 C5016002 LOCKNUT M25 31 1 30 1 C700106607000 EDGE PROTECTOR, CUT 7.000" 22 1 C2010066 CONNECTION, GAS, SINGLE 3/4" 20 1 C5016001 FITTING, ELECTRICAL, LIQUID TIGHT 19 1 C2016147 CONDENSER HOSE ASSY, GAS 18 1 C2016130 ASSY, WATER VALVE, GAS, 10.10 17 1 C2616452 BOTTOM FLAP, PUMP HOUSING GAS 10.10 110V PREASSEMBLED (NOT SHOWN) 16 1 C5215897 CABLE HARNESS, ILLUMINATION 15 5 C8005021 WASHER, 4.3, DIN 125 14 7 C8013004 HEXAGON BOLT M4 X 10 13 3 C8003029 MLF, SCREW, M5x10 12 1 111551 TRAY, DRIP, FAN, REAR, ELECTRIC & GAS INJ, 6.10/10.10 11 1 111522 TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10 10 2 111538 ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH 9 1 C6005021 RUBBER BUSHING 42 MM OD 8 1 C70016603000 EDGE PROTECTOR, CUT 3.000" 6 4 C8003035 HEXAGON BOLT M5X10 5 5 C8006058 SCHNORR LOCK WASHER 4 1 C5011003 CONNECTION FLANGE 3 1 C2216088 AIR INLET BOX FINAL ASSEMBLY 2 1 C2114699 ASSEMBLY, TOP COVER, PUMP HOUSING, AUTO CLEAN SYSTEM 1 1 C2114520 OUTER BASE, EL, 6.10/10.10

C700106607000-1

EDGE PROTECTOR, CUT 7.000"

C2114535 A

0706

34

1

33

1

32

1

9

13

17

1

11

1

9

5

20

1

4

5

7

1

6

3

8

1

4

14

21

2

10

4

12

BASE, GAS,

42

INJECTOR, NO CLEANING

OGS 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2114520 OUTER BASE, EL, 6.10/10.10 2 1 C2216088 AIR INLET BOX FINAL ASSEMBLY 3 1 C5011003 CONNECTION FLANGE 4 5 C8006058 SCHNORR LOCK WASHER 5 4 C8003035 HEXAGON BOLT M5X10 7 1 C70016603000 EDGE PROTECTOR, CUT 3.000 8 1 C6005021 RUBBER BUSHING 42 MM OD" 9 2 111538 ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH 10 1 111522 TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10 11 1 111551 TRAY, DRIP, FAN, REAR, ELECTRIC & GAS INJ, 6.10/10.10 12 3 C8003029 MLF, SCREW, M5x10 13 7 C8013004 HEXAGON BOLT M4 X 10 14 5 C8005021 WASHER, 4.3, DIN 125 15 1 C5215897 CABLE HARNESS, ILLUMINATION 16 1 C2016147 CONDENSER HOSE ASSY, GAS 17 1 C5016001 FITTING, ELECTRICAL, LIQUID TIGHT 19 1 C2016131 ASSEMBLY, WATER VALVE, ELECTRIC INJECTOR, 6.20 20 1 C2114626 COVER, BOTTOM, PUMP HOUSING 21 1 C2010066 CONNECTION, GAS, SINGLE 3/4" 32 1 C700106607000 EDGE PROTECTOR, CUT 7.000" 33 1

C700106607000-1

EDGE PROTECTOR, CUT 7.000"

34 1 C5016002 LOCKNUT M25

C21145351 A

0706

NOT SHOWN

327

2

19

4

13

8

7

1

5

15

18

22

16

15

16

12

10

DETAIL A

A

10

20

17

12

BASE, GAS,

43

Pressure Switch C5009055 Agent Pump 300352

GENERATOR, WITH CLEANING

OGB 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2114542 ASSEMBLY, OUTER BASE, GAS, STEAM GEN, 6.20/10.20 2 1 C2114699 ASSEMBLY, TOP COVER, PUMP HOUSING, AUTO CLEAN SYSTEM 3 1 C2616451 BOTTOM FLAP, PUMP HOUSING, GAS, 6.20, 110V 4 1 C2016147 CONDENSER HOSE ASSY, GAS 5 1 C2010068 DOUBLE GAS CONNECTION R 3/4" 7 1 C2016129 ASSEMBLY, WATER VALVE, GAS, 6.20, GEN W / CLEANING SYSTEM 8 1 C5011003 CONNECTION FLANGE 10 5 C8006058 SCHNORR LOCK WASHER 11 2 C8003035 HEXAGON BOLT M5X10 12 1 C5016001 FITTING, ELECTRICAL, LIQUID TIGHT 13 1 C5016002 LOCKNUT, M25, 15 5 C8005021 WASHER, 4.3, DIN 125 16 7 C8013004 HEXAGON BOLT M4 X 10 17 1 111522 TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10 18 1 111524 TRAY, DRIP, FAN, REAR, 6.20/20.20 19 1 C2116092 BOX, AIR INTAKE 20 3 C8003029 MLF, SCREW, M5x10 21 1 C70016603000 EDGE PROTECTOR, CUT 3.000" 22 2 111538 ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH 23 1 C5215897 CABLE, HARNESS, ILLUMINATION 27 1 111752 PLUG, 1.500 DIA, HOLE, SNAP-IN 28 1 C2216090 FAN, AIR INLET BOX ASSEMBLY 29 1 C700106607000 EDGE PROTECTOR, CUT 7.000" 30 1

C700106607000-1

EDGE PROTECTOR, CUT 7.000"

C21145471 A

0706

NOT SHOWN

1

C2114542

ASSEMBLY, OUTER BASE, GAS, STEAM GEN, 6.20/10.20, P3

21

C2016147

CONDENSER HOSE ASSY, GAS

3

1

C

2010068 DOUBLE GAS CONNECTION R 3/4" P3

5

1

C5011003 CONNECTION FLANGE

7

5

C8006058 SCHNORR LOCK WASHER S5 A2 P3

8

2

C8003035 HEXAGON BOLT M5X10 A2 P2 P3

9

1

C

5016001

FITTING, ELECTRICAL, LIQUID TIGHT

1

0

1

C5016002

LOCKNUT, M25, P3

12

5

C

8005021

WASHER, 4.3, DIN 125

1

3

7

C

8013004 HEXAGON BOLT M4 X 10 A2 P3

14 1

111522

TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10

151111524

TRAY, DRIP, FAN, REAR, 6.20/20.20

16

1

C2116092

B

OX, AIR INTAKE P3

17 1

C2016126

A

SSY, WA TER VALVE, GAS, 6.20

18

1

C2114626

COVER, BOTTOM, PUMP HOUSING P3

19 3

C8003029

MLF, SCREW, M5x10 A2 P2 P3

20

1

C700166030

EDGE PROTECTOR, CUT 3.000"

00

20

18

7

8

16

2

10

A

17

13

7

21

9

14

19

5

12

3

12

1

15

DETAIL A

BASE, GAS,

44

GENERATOR, NO CLEANING

OGB 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2114542 ASSEMBLY, OUTER BASE, GAS, STEAM GEN, 6.20/10.20 2 1 C2016147 CONDENSER HOSE ASSY, GAS 3 1 C2010068 DOUBLE GAS CONNECTION R 3/4" 5 1 C5011003 CONNECTION FLANGE 7 5 C8006058 SCHNORR LOCK WASHER 8 2 C8003035 HEXAGON BOLT M5X10 9 1 C5016001 FITTING, ELECTRICAL, LIQUID TIGHT 10 1 C5016002 LOCKNUT, M25 12 5 C8005021 WASHER, 4.3, DIN 125 13 7 C8013004 HEXAGON BOLT M4 X 10 14 1 111522 TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10 15 1 111524 TRAY, DRIP, FAN, REAR, 6.20/20.20 16 1 C2116092 BOX, AIR INTAKE 17 1 C2016126 ASSY, WATER VALVE, GAS, 6.20 18 1 C2114626 COVER, BOTTOM, PUMP HOUSING 19 3 C8003029 MLF, SCREW, M5x10 20 1 C70016603000 EDGE PROTECTOR, CUT 3.000" 21 2 111538 A DAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH 23 1 C5215897 CABLE, HARNESS, ILLUMINATION 29 1 C2216090 FAN, AIR INLET BOX ASSEMBLY 30 1 111752 PLUG, 1.500 DIA, HOLE, SNAP-IN 31 1 C700106607000 EDGE PROTECTOR, CUT 7.000" 32 1

C700106607000-1

EDGE PROTECTOR, CUT 7.000"

C21145472 A

0706

19

17

2

1

2

0

2

5

15

3

1

10

23

15

16

8

14

16

12

DETAIL A

A

12

13

9

21

BASE, GAS,

45

Pressure Switch C5009055 Agent Pump 300352

INJECTOR, WITH CLEANING

OGS 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2114522 ASSEMBLY, OUTER PLATE EL 6.20/10.20 2 1 C2114699 ASSEMBLY, TOP COVER, PUMP HOUSING, AUTO CLEAN SYSTEM 3 1 C2016127 ASSY, WATER VALVE, GAS, 6.20 5 1 C5011003 CONNECTION FLANGE 8 2 111538 ADAPTER, 3/4-14 BSPP FEMALE X 3/4 GHT MALE, GH 9 1 111522 TRAY, DRIP, FAN, FRONT, 6.20/20.20/10.10 10 1 111524 TRAY, DRIP, FAN, REAR, 6.20/20.20 11 1 C2116092 BOX, AIR INTAKE 12 5 C8006058 SCHNORR LOCK WASHER 13 3 C8003029 MLF, SCREW, M5x10 14 7 C8013004 HEXAGON BOLT M4 X 10 15 5 C8005021 WASHER, 4.3, DIN 125 16 4 C8003035 HEXAGON BOLT M5X10 17 1 C70016603000 EDGE PROTECTOR, CUT 3.000" 18 1 C5215897 CABLE HARNESS, ILLUMINATION 19 1 C2616451 BOTTOM FLAP, PUMP HOUSING, GAS, 6.20, 110V 20 1 C2016147 CONDENSER HOSE ASSY, GAS 21 1 C5016001 FITTING, ELECTRICAL, LIQUID TIGHT 22 1 C5016002 LOCKNUT, M25 (NOT SHOWN) 23 1 C2010066 CONNECTION, GAS, SINGLE 3/4" 30 1 C2216090 FAN, AIR INLET BOX ASSEMBLY 31 1 111752 PLUG, 1.500 DIA, HOLE, SNAP-IN 32 1 33 1 C700106607000 EDGE PROTECTOR, CUT 7.000"

C700106607000-1

EDGE PROTECTOR, CUT 7.000"

C2114537 A

0706

1

2

53

4

ASSEMBLY, WATER HOSE SYSTEM, CONDENSER

46

Connecter Flange C5011003

ALL MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C6015215 ELBOW, HOSE CONNECTION, 3/8" WITH SEAL 2 2 111647 CLAMP, OETIKER, S/S, 19/32" 3 1 11149811000 HOSE, SILICONE, 3/8" ID X 11.000 4 1 300455 VALVE ASSEMBLY, 1 WAY, 120 VAC 5 1 300407 FILTER, ELECTRICAL 6 2 300509 TERMINAL, 18-22 AWG PIGGY BACK

C2016147 A

0706

10

8

4

3

9 11

11

12

3

6

5

6

3

8

3

1

2

ASSEMBLY, WATER VALVE

47

ALL GAS 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 3 300407 FILTER, ELECTRICAL 2 6 300509 TERMINAL, 18-22 AWG PIGGY BACK 3 4 111498 HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH) 4 7 111647 CLAMP, OETIKER, S/S, 19/32" 5 1 C5001085 PRESSURE REGULATING VALVE ODGAS 6 2 C6015401 BARB, 1/2 R X 3/8 HOSE 7 1 C6015232 CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20 8 1 C6006140 GAUGE, 60 PSI BOTTOM MOUNT 9 1 C5009063 PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT) 10 1 300363 TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º 11 A/R 00946 TAPE, TEFLON, 1/2" 12 A/R 111561 SEALANT, LOCTITE, WHITE, DRI-SEAL, 513

C2016038 B

0706

10

8

4

3

9 11

11

12

3

6

5

6

3

8

3

1

2

ASSEMBLY, WATER VALVE

48

10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 3 300407 FILTER, ELECTRICAL 2 6 300509 TERMINAL, 18-22 AWG PIGGY BACK 3 4 111498 HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH) 4 7 111647 CLAMP, OETIKER, S/S, 19/32" 5 1 C5001085 PRESSURE REGULATING VALVE ODGAS 6 2 C6015401 BARB, 1/2 R X 3/8 HOSE 7 1 C6015232 CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20 8 1 C6006140 GAUGE, 60 PSI BOTTOM MOUNT 9 1 C5009063 PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT) 10 1 300363 TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º 11 A/R 00946 TAPE, TEFLON, 1/2" 12 A/R 111561 SEALANT, LOCTITE, WHITE, DRI-SEAL, 513

C2016130 A

0706

TOLERANCES

(UNLESS OTHERWISE

NOTED)

A

NGULAR

`

D

ECIMAL

0.030

1∞

2

6

511

7 8 11

2 2

1

312

4

312

9

10

ASSEMBLY, WATER VALVE, INJECTOR, GAS

49

OGS 6.20 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 300456 VALVE ASSY. 2 WAY 120VAC 2 4 111498 HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH) 3 2 C6015401 BARB, 1/2 R X 3/8 HOSE 4 1 C5001085 PRESSURE REGULATING VALVE OD GAS 5 1 C6006140 GAUGE, 60 PSI BOTTOM MOUNT 6 6 111647 CLAMP, OETIKER, S/S, 19/32" 7 1 C6015232 CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20 8 1 C5009063 PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT) 9 2 300407 FILTER, ELECTRICAL 10 4 300509 TERMINAL, 18-22 AWG PIGGY BACK 11 A/R 00946 TAPE, TEFLON, 1/2" 12 A/R 111651 SEALANT, LOCTITE, WHITE, DRI-SEAL 513

C2016128 A

0706

CLEVELAND RANGE, LLC

1

333 East 179th St., Cleveland, Ohio 44110-2574

T

HIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

T

OLERANCES

(UNLESS OTHERWISE

NOTED)

DO NOT SCALE PRINTED DRAWING

DRAWN BY DATE

TITLE

ANGULAR

`

DECIMAL

0.030

1∞

ASSEMBLY, WATER SUPPLY GEN W/CLEANING SYSTEM 6.20 P3

CCE

D

C2016035

7

1

111646

TEE, BRASS, 3/8" BRASS

6 6 111647

CLAMP, OETIKER, S/S, 19/32"

5

1

1114981100

HOSE, SILICONE, 3/8" ID X 11.000

0

4

2

1

114980400

HOSE, SILICONE, 3/8" ID X 4.000

0

311114983350

HOSE, SILICONE, 3/8" ID X 24.375

0

21

1114982637

HOSE, SILICONE, 3/8" ID X 26.375

5

1

3

00453

V

ALVE ASSEMBLY, 3WAY 240VAC

ITEM

QTY

PART N0.

DESCRIPTION

CLEANING

DEHUMIDIFICATION

S

TEAM GENERATO R

2

2 2

1

2

4

ASSEMBLY, WATER SUPPLY, GENERATOR W/CLEANING SYSTEM

50

OEB & OGB 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 300453 VALVE ASSEMBLY, 3WAY 240VAC

300363 TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º 2 5 111498 HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH) 3 6 111647 CLAMP, OETIKER, S/S, 19/32" 4 1 111646 TEE, BRASS, 3/8" BRASS

C2016035 A & C2016129 A

0706

4

3

2

5

2

1

ASSEMBLY, WATER VALVE

51

ALL GAS 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 300456 VALVE ASSY. 2 WAY 120VAC 2 2 111498 HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH) 3 2 111647 CLAMP, OETIKER, S/S, 19/32" 4 2 300407 FILTER, ELECTRICAL 5 4 300509 TERMINAL, 18-22 AWG PIGGY BACK

C2016126 A

0706

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

T

HIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

TOLERANCES

(UNLESS OTHERWISE

NOTED)

PRINTED DRAWING

TITLE

ANGULAR

`

DECIMAL

0.030

1∞

1511114981937

5

1

41

C5009063

13

1

C6006140

1

21

C6015232 CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20 P3

11 2

C

6015401

1

0

1

C5001085 PRESSURE REGULATING VALVE ODGAS P3

921

114980237

5

821

114980400

0

7

1

11646 6 10 111647 5

1

114981100

0

4

1

114982437

5

3

6 300509

2

3 300407

11

300453

ITEM

QTY

PART N0.

5

1

10

4

11

4

8

7

8

4

9

4

2

4

2

3

4

6

ASSEMBLY, WATER VALVE

52

OGS 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 300363 TRIPLE SOLENOID VALVE 110-120V 50/60 Hz 180º (OGS 6.20) 2 3 300407 FILTER, ELECTRICAL 3 6 300509 TERMINAL, 18-22 AWG PIGGY BACK 4 5 111498 HOSE, SILICONE, 3/8" ID (SPECIFY LENGTH) 5 10 111647 CLAMP, OETIKER, S/S, 19/32" 6 1 111646 TEE, BRASS, 3/8" BRASS 7 1 C5001085 PRESSURE REGULATING VALVE ODGAS 8 2 C6015401 BARB, 1/2 R X 3/8 HOSE 9 1 C6015232 CONNECTION NOZZLE 0.6MM 6.20/10.10/10.20 10 1 C6006140 GAUGE, 60 PSI BOTTOM MOUNT 11 1 C5009063 PUSH BUTTON SWITCH, INJ, (CHANGE-OVER CONTACT)

C2016127 A

0706

B

C

D

NOT SHOWN

1615

5

9

6

3

10

8

6

1

17

1

3

2

11 12

7

11 12

7

10

14 4

ASSEMBLY, STEAM GENERATOR, GAS

53

OGB 6.20 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2314891 WELDMENT, GEN GAS 6.20 (NOT SHOWN) 2 1 C2314243 SUPPORT, STEAM GEN, TABLE TOP UNIT 3 1 C5016006 THERMOCOUPLE, SENSOR, OSC/OSP, 64.960" (1650MM) 4 1 C2314991 PUMP, 110V, GAS STEAM GENERATOR 5 1 C5019003 ASSEMBLY, DOUBLE LEVEL PROBE 6 2 C6015023 FLAT GASKET FOR IMMERSION HEATER 7 1 C2314968 INSPECTION FLANGE, STEAM GENERATOR 8 1 C6005260 SEAL, THERMOCOUPLE SENSOR, OSC/OSP 9 1 C6015040 FLAT GASKET FOR DOUBLE-LEVEL PROBE 10 1 C2314974 FLANGE, INSPECTION, STEAM GENERATOR 11 15 C8017011 NUT, FLANGE, HEX 12 A/R C7014000 COPPER PASTE 13 1 06240 FTG, HOSE BARB, 3/4 X 3/4 MPT 14 1 C6006089 HOSE CLAMP, 40-60 MM 15 2 C6005025 FLAT GASKET, 1.673 x 2.126 x 0.079 in. 16 1 C6006092 HEXAGON NUT R 1 1/4" 17 1 05231 ELBOW, STREET 90 X 3/4 NPT, BRASS 18 11 101953 CLIP, INSULATION RETAINER, 1-1/2, .105 HOLE, GALV.

C2314881 D

0706

7

3

4 4

5

6

22

1

PUMP, STEAM GENERATOR, GAS, 110V

54

C6015101

ALL GAS MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C6015100 DRAIN ELBOW FOR STEAM GENERATOR 2 1 C6005299 SUPPORT BUSHING, STEAM GENERATOR - PUMP 3 1 C8009057 WIRE CLAMP D: 36, BLACK 4 1 300506 DRAIN PUMP WITH 110 V MOTOR 5 1 111630 BRACKET, PUMP, GAS GEN 6 4 111633 SCREW, HEX HD, M3 x 16, SST, FULLY THREADED 7 4 C8017008 NUT, LOCKING, SERRATED

C2314991 C

0706

(

NOT SHOWN)

(NOT SHOWN)

10

26

17

18

16

18

6

8

1

2

15

20

25

4

5

21 23 9

2

12

13

14

11

19

24

20 25

3

10

26

7

8

27 28

21

ASSEMBLY, BURNER INSERT, STEAM GENERATOR, NAT GAS

55

Burner Intake Hose C701210023675

OGB 6.20 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2010045 BURNER INSERT GEN STEAM 6.10/6.20/10.10 WELDED 2 1 C6015032 SEAL, BURNER ø 50 MM 3 1 C2615351 RESTRICTION FLANGE ø 210 RG128 4 1 C2010014 BURNER, ø 50 x150, 20 KW 5 1 C2614907 CLAMPING FLANGE, STEAM GENERATOR, BURNER, ø 50 6 1 C4018000 MONITORING ELECTRODE 7 1 C4018002 AUTO-IGNITION ELECTRODE 8 2 C6015037 SEAL, ELECTRODE 9 1 C5018006 BURNER BLOWER, RG128, 110V 10 2 C6015034 SEAL, FAN RG128/148 11 1 C6016000 VENTURI 40 KW 12 1 C6016009 GAS VALVE, HONEYWELL, 110V 13 1 C6017009 ORIFICE, ø 05.65 NAT GAS 14 1 C6016030 SEALING RING, GAS SCREEN 15 1 C2615367 FLANGE, BURNER 16 1 C5015004 INSPECTION GLASS, BURNER 17 1 C2614845 COVER, INSPECTION GLASS, BURNER 18 2 C6015039 SEAL, INSPECTION GLASS, BURNER 19 5 C8012001 SCREW, M5x12, FILLISTER HD, TORX 20 A/R C7014000 COPPER PASTE 21 1 C6016023 AUTOMATIC FIRING DEVICE, 110V, AUTO-IGNITION 22 1 C6016025 COVER, AUTOMATIC FIRING DEVICE 23 1 C2616516 GAS HOSE, 580 LG, PREASSEMBLED 24 1 111595 GASKET, CORK, BURNER VENTURI, COMBI 25 8 C8017010 FLANGE NUT 26 6 C8017008 NUT, LOCKING, SERRATED 27 1 300484 TERM, PUSHON, .110, 22-16AWG SEMI INSUL. 28 1 20351 TERM, SLIPON FULL INSUL .032X.25 TAB 22-18AWG

C2314900 B

0706

8

18

5

10

4

10

6

7

2

18

19 20

3

9

1

15 16

12

14

13

11

17

BURNER INSERT, HL, PRE-MOUNTED

56

ALL GAS MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2010050 BURNER INSERT HL, 6.10/6.20, WELDMENT

1 C2010052 BURNER INSERT, HL, 10.10/20.10, WELDMENT 2 1 C4018002 AUTO-IGNITION ELECTRODE 3 1 C4018000 MONITORING ELECTRODE 4 1 C5015004 INSPECTION GLASS, BURNER 5 1 C2614845 COVER, INSPECTION GLASS, BURNER 6 2 C6015240 WASHER, CABLE BUSHING, BURNER INSERT 7 1 C6015041 SEAL, CABLE BUSHING BURNER INSERT 8 1 C6015238 SCREW CONNECTION, CABLE BUSHING, BURNER INSERT 9 2 C2614849 LINING PLATE, ELECTRODE, GAS 11 1 C2614842 CLAMPING FLANGE, BURNER, HL, ø 50 10 2 C6015039 SEAL, INSPECTION GLASS, BURNER 12 1 C6015032 SEAL, BURNER ø 50 MM 13 1 C2010014 BURNER, ø 50 x150, 20 KW 14 1 C2615367 FLANGE, BURNER 15 A/R C7014000 COPPER PASTE 16 4 C8017010 FLANGE NUT 17 4 C8003095 HEXAGON BOLT, M5x16, HUD 20.20 18 6 C8017008 NUT, LOCKING, SERRATED 19 1 300484 TERM, PUSHON, .110, 22-16AWG SEMI INSUL. (NOT SHOWN) 20 1 20351 TERM, SLIPON FULL INSUL .032X.25 TAB 22-18AWG (NOT SHOWN)

C2616521 C & C2616522 B

0706

15 1

41 13 12 1 11

A/R 10 9 8 7 6 5 4 3 22 11

9

4

2

14

2

1

8

12

5

6

15

10 13 11

7

ASSEMBLY, BURNER INSERT, AIR, LP & NAT GAS

57

Burner Intake Hose C701210023675

ALL GAS MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2616521 BURNER INSERT, HL, PRE-MOUNTED, 6.10/6.20

1 C2616522 BURNER INSERT, HL, PRE-ASSEMBLED, 10.10/20.10 2 2 C6015034 SEAL, FAN RG128/148 3 1 C5018006 BURNER BLOWER, RG128, 110V 4 1 C6016009 GAS VALVE, HONEYWELL, 110V 5 1 C6016030 SEALING RING, GAS SCREEN 6 1 C6016000 VENTURI 40 KW 7 5 C8012001 SCREW, M5x12, FILLISTER HD, TORX 8 1 C6016023 AUTOMATIC FIRING DEVICE, 110V, AUTO-IGNITION 9 1 C6016025 COVER, AUTOMATIC FIRING DEVICE 10 1 C2616516 GAS HOSE, 580mm LG, PREASSEMBLED, 6.20

1 C2616517 GAS HOSE, 780mm LG, PREASSEMBLED, 10.10/20.10 11 A/R C7014000 COPPER PASTE 12 1 C6017001 ORIFICE ø 400, LP GAS

1 C6017009 ORIFICE, ø 0565 NAT GAS 13 4 C8017010 FLANGE NUT 14 1 C2615355 FLANGE, RESTRICTION ø 250 15 1 111595 GASKET, CORK, BURNER VENTURI, COMBI

C2614860-1 A, C2614860 B, C2614862-1 B & C2614862 B

0706

2

4

1

3

5

6

7

8

DOOR 6.20 COMPLETE

58

Spring clip C6015248

OES 6.20 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2514358 ASSEMBLY, OUTER DOOR, 6.20

2 1 C2514389 ASSEMBLY, INNER DOOR, 6.20

3 1 C6012000 DOOR HANDLE, LOCKING 4 1 C6009016 PLASTIC LETTER "C" RED 5 2 C8015000 MLF SCREW M6X8 6 1 C2514430 UNHINGING SAFEGUARD, DOOR 7 1 C8001024 SCREW, FILISTER HD, M4x10 DIN 7985 8 1 C8005021 WASHER, 4.3, DIN 125 9 A/R C7004012 LOCTITE 243 (NOT SHOWN) 10 A/R C7003087 GREASE FRONT DOORS OD

1 C2514359 ASSEMBLY, OUTER DOOR, 10.10

1 C2514390 ASSEMBLY, INNER DOOR, 10.10

40 C2514351SERV A & C2514352SERV A

0706

A

E

D

E

B

C

INSTALLED

ORIENTATION

17

SLIDING PLATE, COMPLETE

59

Upper Hinge C2013006

ALL 6.20 &10.10 MODELS

Page 1 of 2

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2614806 CARRIAGE PLATE, WELDED, 6.20

C2614807 CARRIAGE PLATE, WELDED, 10.10 & 10.20

C2614809 CARRIAGE PLATE, WELDED, 20.10 & 20.20 2 2 C6012002 ASSEMBLED,GUIDE ROLLER RST CPL 3 2 C6012005 DISC ø 39 x 6 RST 4 2 C2014008 LOCKING BLOCK, CARRIAGE PLATE 5 2 C6015226 LOCKING BLOCK RST 6 2 C6012006 DOOR STOP, RST 7 1 C2013004 HINGE, LOWER, WELDMENT, DOOR 8 11 C8006057 SCHNORR LOCK WASHER 9 2 C8006063 SCHNORR-LOCK WASHER 10 5 C8006060 SCHNORR LOCK WASHER 11 4 C8004057 NUT, HEX 12 1 C8005050 WASHER, 8.4 A2 DIN 125 13 1 C8003058 HEXAGON BOLT, M8 X 35 14 11 C8003043 HEXAGON BOLT M6x16 15 4 C8013002 FILLISTER HEAD SCREW DIN 912 - M8X25 16 2 C8008095 BLIND RIVET NUT M6 ROUND 17 2 C8001073 HEXAGON SOCKET SCREW M6x16 18 2 C8004040 HEXAGON NUT 19 1 C2014004 LOCKING PLATE, CARRIAGE, LOWER PART 20 7 C8005041 WASHER 6.4 A2 DIN 9021 21 A/R C7004014 LOCTITE 638 22 2 C8003066 BOLT, HEX HD, M10x30, 6.20, 10.10 & 10.20

C8013000 BOLT, HEX HD, M10x25, 20.10 & 20.20

C2614801 B, C2614802 B & C2614804 P1

0706

SECTION E-E

DETAIL C

DETAIL B DETAIL A

SECTION D-D

4

1

19 20 8

14721

13 21

4

2

161

8

20

11 21

10

17

22

14 21

3 9

6

15

5

8 14

4

18

SLIDING PLATE, COMPLETE

60

ALL 6.20 & 10.10 MODELS

Page 2 of 2

C2614801 B, C2614802 B & C2614804 P1

0706

5

4

3

2

1

EXTERIOR SHEETING

61

ALL 6.20 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C2514351 DOOR, 6.20, COMPLETE

- 1 C2514352 DOOR, 10.10, COMPLETE 2 1 C2114652 WELDMENT, CORNER, FRONT LEFT, 6.20

- 1 C2114653 WELDMENT, CORNER, FRONT LEFT, 10.10 3 1 C2114782 PANEL ASSY, LEFT, OGB 6.20, OGS 6.20, OEB 6.20, OES 6.20

- 1 C2114783 PANEL ASSY, LEFT, OGB 10.10, OGS 10.10, OEB 10.10, OES 10.10 4 1 C2114762 PANEL ASSY, REAR, OGB 6.20

- 1 C2114742 PANEL ASSY, REAR, OGS 6.20, OEB 6.20, OES 6.20

- 1 C2114763 PANEL ASSY, REAR, OGB 10.10

- 1 C2114743 PANEL ASSY, REAR, OGS 10.10, OEB 10.10, OES 10.10 5 1 C2115462 PANEL, TOP, OGB 6.20

- 1 C2115452 PANEL, TOP, OGS 6.20

- 1 C2114702 PANEL, TOP, OEB 6.20

- 1 111628 PANEL, TOP, OES 6.20

- 1 C2115463 PANEL, TOP, OGB 10.10

- 1 C2115453 PANEL, TOP, OGS 10.10

- 1 C2114700 PANEL, TOP, OEB 10.10

- 1 111638 PANEL, TOP, OES 10.10

SERVICE SHEETING

0706

7

11

1

13

6

8

12

4

3

14

15

16

2

5

10

9

18

17

STAND, ASSEMBLY, CLOSED BASE

63

FK111934 CASTOR STEM REPLACEMENT KIT

Caster w/brake 111644 Caster w/o brake 111645

6.10 & 10.10 MODELS

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C3216201 WELDMENT, STAND, COMBI, 6.10/10.10 2 2 100413 FOOT ASS'Y, ADJUSTABLE (FOR 1.250 SQ. TUBING), ANCHORABLE TIEDOWN 3 1 C3216245 WELDMENT, STAND DOOR, 6.10/10.10, LEFT SIDE 4 1 C3216249 WELDMENT, STAND DOOR, 6.10/10.10, RIGHT SIDE 5 2 100241 FOOT, ADJUSTABLE (FOR 1.250 SQ. TUBE) 6 2 C3216237 PANEL, STAND, LEFT & RIGHT SIDE, 6.10/10.10 7 1 C3216238 SHEETING, TOP & REAR, COMBI STAND, 6.10/10.10 8 4 111673 HINGE, COMBI STAND 9 1 111674 CATCH, MAGNETIC, COMBI STAND 10 2 110492 SCREW, 6-32 X 0.312, PAN HD, PHILLIPS, SST 11 3 104080 SCREW, TR, PHH, 8x1/2, TYPE B, SST 12 24 111686 SCREW, 10-32 X 0.500, COUNTERSUNK FLAT HEAD, SST 13 8 111687 STUD, WELD, 6-32 X 0.188, CD, SST, NO FLANGE 14 8 110715 WASHER, 0.158 ID X 0.340 OD X 0.032 THK, SST 15 8 23154 WASHER, LOCK, INTERNAL TOOTH, #6, SST 16 8 14262 NUT, HEX, 6-32, ACORN, SST 17 1 110587 LABEL, SANITATION, UL CLASS NSF #2 18 1 111669 LABEL, COMBI STAND, MODEL NO. CST-10-CB (6.10, 10.10)

C3216313 B

0706

USED FOR STEAM GENERATOR

1

2

8

9 18

14

16

1

3

15

19

17

7

5

10

4

6

2

12

11

ASSEMBLY, STACKING KIT, GAS MODELS

64

6.20 ON 6.20 OR 10.20,

6.10 ON 6.10 OR 10.10,

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1 1 C3416377 WELDMENT, BASE, STACKING KIT, GAS, 6.20/10.20 2 1 C3416369 WELDMENT, EXHAUST SHIELD, STACKING KIT, GAS 3 1 C3416363 SHROUD, STACKING KIT, GAS, 6.20

1 C3416361 SHROUD, STACKING KIT, GAS, 6.10 4 1 C2016200 PIPE, STEAM EXHAUST, GAS, STACKING KIT 5 1 C2016211 FLUE PIPE, STEAM GENERATOR, STACKING KIT, 6.20

1 C2016212 FLUE PIPE, STEAM GENERATOR, STACKING KIT, 6.10 6 1 C3416373 SHROUD, EXHAUST, STACKING KIT, GAS 7 1 C3417044 BRACKET, COVER PLATE, STACKING KIT, GAS 8 1 C3416372 COVER, EXHAUST SHROUD, STACKING KIT, GAS 9 1 C3416392 GUIDE, FLUE, SHROUD, TOP, STACKING KIT, GAS 6.20

1 C3416374 GUIDE, FLUE SHROUD, TOP, STACKING KIT, GAS, 6.10 10 1 C2016204 FLUE PIPE, HOT AIR, STACKING KIT. 6.20

1 C2016206 FLUE PIPE, HOT AIR, STACKING KIT, 6.10 11 4 06162 FOOT, 6.00" ADJUSTABLE, FLANGED/TRI-BOLT HOLE PATTERN 12 20 C8001024 SCREW, FILISTER HD, M4x10 DIN 7985 14 1 05250 ELBOW, 90º, 1/2 NPT, BRASS (USED FOR STEAM GENERATOR) 15 1 05253 ELBOW, STREET, 90º, 1/2 NPT, BRASS (USED FOR STEAM GENERATOR) 16 1 14335 NIPPLE 0.500 NPT X 4.000, SCH 40, BRASS, TBE (USED FOR STEAM GENERATOR) 17 1 108034 WASHER 3/4 GHT HOSE (USED FOR STEAM GENERATOR) 18 1 111704 FITTING, 3/4 GHT MALE, X 1/2 NPT MALE, BRASS (USED FOR STEAM GENERATOR) 19 1 111705

FITTING, 3/4 GHT FEMALE SWIVEL X 1/2 NPT FEMALE, BRASS (USED FOR STEAM GENERATOR) 20 A/R 00909 THREAD SEALANT, LOCTITE 592 (USED FOR STEAM GENERATOR) 22 1 111702 AIR DUCT, STACKING KIT, X.20 (USED FOR STEAM GENERATOR)

1 111703 AIR DUCT, STACKING KIT, X.10 (USED FOR STEAM GENERATOR)

C3417021 C & C3417019 B

0706

1

2

6

3

4

9

13

11

7

5

6

12

8

1

0

ASSEMBLY, STACKING KIT,

65

ELECTRIC MODELS

6.10 ON 6.10 OR 10.10

IITTEEMM QQTTYY PPAARRTT NN00.. DDEESSCCRRIIPPTTIIOONN

1* 1 C3416368 WELDMENT, BASE, STACKING KIT, ELECTRIC, 6.10/10.10 2* 1 C3416362 SHROUD, STACKING KIT, ELECTRIC, X.10 3* 1 C3416365 BRACKET, STEAM EXHAUST PIPE, STACKING KIT, ELECTRIC 4* 1 C2016201 PIPE, STEAM EXHAUST, ELECTRIC, STACKING KIT 5* 4 06162 FOOT, 6.00" ADJUSTABLE, FLANGED/TRI-BOLT HOLE PATTERN 6* 3 C8001024 SCREW, FILISTER HD, M4x10 DIN 7985 7* 1 111703 AIR DUCT, STACKING KIT, x.10 8 1 05250 ELBOW, 90º, 1/2 NPT, BRASS 9 1 05253 ELBOW, STREET, 90º, 1/2 NPT, BRASS 10 1 14335 NIPPLE 0.500 NPT X 4.000, SCH 40, BRASS, TBE 11 1 108034 WASHER 3/4 GHT HOSE 12 1 111704 FITTING, 3/4 GHT MALE, X 1/2 NPT MALE, BRASS 13 1 111705 FITTING, 3/4 GHT FEMALE SWIVEL X 1/2 NPT FEMALE, BRASS 14 A/R 00909 THREAD SEALANT,LOCTITE 592

* Used for Steam Generator only.

C3417017 D

0706

CLEVELAND RANGE OGB 6.20/10.10

66

SEQUENCE OF OPERATIONS

When using these instructions refer to the OGB 6.20/10.10 wiring schematic.

1 When 120 VAC is applied to the combi, it is sent through the line filter (Z1) to the

Power Control Switch (S1).

2 When the Power Control Switch (S1) is closed

a The red light in the switch is energized. b 120 VAC is sent through the 7 amp fuse (F10) to terminal 1 of connector X11 on

the Motor Drive (U10)

c 120vac is sent through the 2 amp fuse (F1.1) to

• The primary of the Hot Air 24v Transformer (T1) ◊ 24 VAC is sent from the secondary of the transformer to the Hot air

Burner Control (N20)

• The primary of the Steam 24v Transformer (T2) ◊ 24 VAC is sent from the secondary of the transformer to the Steam Burner

Control (N21)

• To terminal 12 of connector X1 on the Hot Air Burner Control (N20)

• To terminal 12 of connector X1 on the Steam Burner Control (N21)

• The 12 VDC Power Supply (G1) ◊ 12 VDC is sent to terminals 1 and 2 of connector X20 on the Gas Board

(A20)

◊ 12 VDC is sent to terminal 3 and 4 of connector X10 on the Control Board

(A10)

• To terminal 2 of connector X1 on the Hot Air Power Burner and Fan Control (U20)

• To terminal 2 of connector X1 on the Steam Power Burner and Fan Control (U21)

• To terminal 1 of connector X12 on the Control Board (A10)

d With 120 VAC to the Control Board (A10) The Operation Board (A11) is

energized

• An alarm will sound for one second

• All the LED’s and the display will energize one at a time.

• “STARTING” will be displayed for 3 seconds

• “Please wait” will be displayed

• The international model number will be displayed

• The time and date will be displayed and this will continue until the on/off

switch is depressed.

3 When the ON/OFF is depressed with the combi in the steam mode

a After a date change (the first time the combi is turned on) the display will ask

“Generator Flush?”. If no answer is given in 10 seconds or a yes is indicated the flush will begin.

• 120 VAC is sent from terminal 1 of connector X13 on the Control Board

67

(A10) to the Generator Pump (M4).

• As the water level drops below the probes the fill solenoid (Y3) will energize. This rocking of the water will help flush scale from the generator.

• Then the pump will be energized again

• When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC

is sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.,

b The display will show the set temperature and set time. c The Control Board (A10) will check the water level by looking for a ground at

terminals 1 and 2 on connector X15. These are connected to the high and low probes (B1) in the steam generator.

• If the ground is not found 120 VAC is sent from terminal 7 on connector X12 on the Control Board (A10) to the fill solenoid (Y3)

• The fill solenoid opens and the generator is filled until both probes are grounded. ◊ If the top probe becomes ungrounded for more that 5 seconds the fill

solenoid (Y3) will energize.

◊ If the bottom probe becomes ungrounded the combi will fill immediately

and the combi will not heat

d When the terminal 2 on connector X15 is grounded, the Control Board (A10)

transmits and receives a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)

• The Gas Board (A20) begins the steam generator heat circuit ◊ A signal is sent from terminal 8 of connector X24 to terminal 4 of

connector X2 on the Steam Power Burner and Fan Control (U21) selecting the set speed of the combustion blower. (a) When this speed is attained the signal is sent from terminal 2 of

connector X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of connector X24 on the Gas Board (A20)

◊ A request for heat is sent from terminal 3 of connector X21 on the Gas

Board (A20) to terminal 10 on connector X1 on the Steam Burner Control Module (N21) (a) 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner

Control Module (N21) to the hot surface igniter (R20).

(b) The gas valve is energized allowing gas and air into the burner

chamber to be ignited by the hot surface igniter.

(c) The Steam Burner Control Module (N21) senses at least 1.5 micro

amps DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 11 of connector X25 on the Gas Board (A20)

• The steam generator heat circuit continues until 190 degrees F is detected from the Steam Generator probe (B4) at terminals 1 and 2 of connector X17 on the Control Board (A10)

4 With the combi in the steam mode with time on the timer, the door closed and the

start switch is depressed

a The front display will include a lighted bar under the steam symbol

68

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

b The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)

c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the

Motor Drive.

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 240 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

• NOTE: If the set temperature is less than 212 degrees F than fan will be

pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).

d The steam generator heat circuit is energized

• A signal is sent from terminal 8 of connector X24 on the Gas Board (A20) to terminal 4 of connector X2 on the Steam Power Burner and Fan Control (U21) selecting the set speed of the combustion blower.

◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of connector X24 on the Gas Board (A20)

• A request for heat is sent from terminal 3 of connector X21 on the Gas Board (A20) to terminal 10 on connector X1 on the Steam Burner Control Module (N21) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner

Control Module (N21) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Steam Burner Control Module (N21) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 11 of connector X25 on the Gas Board (A20)

• The heat circuit continues until both the cabinet set temperature and the bypass probe (B5) are satisfied

◊ NOTE: If the set temperature is above 212 degrees F the hot air circuit

will be energized (after the by pass probe is satisfied) until the compartment setting is reached. The steam circuit always takes precedence.

e When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

f When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

5 With the combi in the Hot Air mode with time on the timer, the door closed and the

69

start switch is depressed b The front display will include a lighted bar under the Hot Air symbol

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

c The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)

d The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the

Motor Drive.

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 240 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

• NOTE: If the set temperature is less than 212 degrees F than fan will be

pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).

e Hot air heat circuit is energized

• A signal is sent from terminal 2 of connector X24 on the Gas Board (A20) to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower.

◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 3 of connector X24 on the Gas Board (A20)

• A request for heat is sent from terminal 3 of connector X20 on the Gas Board (A20) to terminal 10 on connector X1 on the Hot Air Control Module (N20) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 10 of connector X25 on the Gas Board (A20

f The heat circuit will remain energized until the cabinet set temperature is reached

70

g When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

h If the “Crisp and Tasty” mode is selected

• 120 VAC is sent from terminal 6 of connector X12 on the Control Board (A10) to the Dehumidification Valve (Y2) to pull the humidity out of the cabinet down the drain. ◊ In the light and medium modes (one and two drops in the display) the Y2

valve will be energized until the bypass probe (B5) is satisfied.

◊ In the full mode (3 drops in the display) the Y2 valve will be energized

continuously.

i When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

5 With the combi in the Combi mode with time on the timer, the door closed and the

start switch is depressed a The front display will include a lighted bar under the Combi symbol

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

b The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)

c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the

Motor Drive.

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 220 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

• NOTE: If the set temperature is less than 212 degrees F than fan will be

pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).

d The steam generator heat circuit is energized. Steam production takes precedence

in the Combi mode

• A signal is sent from terminal 8 of connector X24 on the Gas Board (A20) to terminal 4 of connector X2 on the Steam Power Burner and Fan Control (U21) selecting the set speed of the combustion blower.

◊ When this speed is attained the signal is sent from terminal 2 of connector

71

X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of connector X24 on the Gas Board (A20)

• A request for heat is sent from terminal 3 of connector X21 on the Gas Board (A20) to terminal 10 on connector X1 on the Steam Burner Control Module (N21) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner

Control Module (N21) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Steam Burner Control Module (N21) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 11 of connector X25 on the Gas Board (A20)

e After the bypass probe (B5) is satisfied then the hot air heat circuit is energized to

increase the cabinet temperature to the setting.

• A signal is sent from terminal 2 of connector X24 on the Gas Board (A20) to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower. ◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 3 of connector X24 on the Gas Board (A20)

• A request for heat is sent from terminal 3 of connector X20 on the Gas Board (A20) to terminal 10 on connector X1 on the Hot Air Control Module (N20)

◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 10 of connector X25 on the Gas Board (A20

• The heat circuit will remain energized until the cabinet set temperature is reached

• If the bypass probe (B5) drops below the set level the steam heat circuit will start again.

f When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

g If the “Crisp and Tasty” mode is selected

• 120 VAC is sent from terminal 6 of connector X12 on the Control Board (A10) to the Dehumidification Valve (Y2) to pull the humidity out of the cabinet down the drain. ◊ In the light and medium modes (one and two drops in the display) the Y2

valve will be energized until the bypass probe (B5) is satisfied.

◊ In the full mode (3 drops in the display) the Y2 valve will be energized

72

continuously.

h When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

6 With the combi in the Rethermalization mode with time on the timer, the door closed

and the start switch is depressed a The front display will include a lighted bar under the Retherm symbol

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

b The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)

c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the

Motor Drive.

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 220 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

• NOTE: If the set temperature is less than 212 degrees F than fan will be

pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).

d The steam generator heat circuit is energized. Steam production takes precedence

in the Combi mode

• A signal is sent from terminal 8 of connector X24 on the Gas Board (A20) to terminal 4 of connector X2 on the Steam Power Burner and Fan Control (U21) selecting the set speed of the combustion blower. ◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Steam Power Burner and Fan Control (U21) to terminal 9 of connector X24 on the Gas Board (A20)

• A request for heat is sent from terminal 3 of connector X21 on the Gas Board (A20) to terminal 10 on connector X1 on the Steam Burner Control Module (N21)

◊ 24 VAC is sent from terminal 2 of connector X2 on the Steam Burner

Control Module (N21) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Steam Burner Control Module (N21) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 11 of connector X25 on the Gas Board (A20)

e After the bypass probe (B5) is satisfied then the hot air heat circuit is en ergized to

increase the cabinet temperature to the setting.

• A signal is sent from terminal 2 of connector X24 on the Gas Board (A20) to

73

terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower. ◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 3 of connector X24 on the Gas Board (A20)

• A request for heat is sent from terminal 3 of connector X20 on the Gas Board (A20) to terminal 10 on connector X1 on the Hot Air Control Module (N20) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 10 of connector X25 on the Gas Board (A20

• The heat circuit will remain energized until the cabinet set temperature is reached

• If the bypass probe (B5) drops below the set level the steam heat circuit will start again.

f When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

g When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

74

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

19

REV

A

12345678

75

BK 12

A

CONTROL POWER

-S1

6

5

RD

4

BK 12 BU 12

L1

3

1

N1

-Z1

LINE FILTER

B

L

N

GND

GR

BU 12

BK 12

C

-X10

1

2

3

L1

N

BU 12

30

102

GND

BU 18

-F1.1

2A

-X10

G

96-264V AC

N

BK 12

12

RD 18

31

RD 18

RD 18L

POWER SUPPLY 12VDC

-A10:X12:1

/3.D6

2

20

-X10

GND

-G1

12V DC

0V

12V

D

BU 18

RD 18

-X13.1

-X13.2

-A10:X10:3

-A20:X28:1

-A10:X10:4

-A20:X28:2

/3.D4

/4.E3

/3.D4

E

/4.E3

-X10:21

/3.F1

BK 12

A

/4.B3

-A20:X26:2

-A20:X26:4

-A20:X26:3

-A20:X26:1

-F10

15A

2 1

B

RD 18

BU 18

RxD

VUGND W

OR

P1 P2

TxD

COM

BK 18

BU 18

L2L1

BN

/3.B5

-A10:X15:9

-A10:X15:10

-A10:X15:11

C

/5.E5

-X10:101

-U10

MOTOR DRIVE

GN 18

-W2 CABLE

12V

BK

GR

D

BK 18

5

4

6

5

4

6

SH

GND

M 3~

TW/GY

U1/BK

V1/BU W1/BN

FAN

TW/GY

-M1

W2/YE

V2/WH

U2/RD

219

91237

873

8

-X13.5

-X13.6

-BM1

RD 18

BU 18

RD 18

3

2

1

3

2

1

BN

BK

RD

RPM

E

WIRING DIAGRAM

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

29

REV

F

A

12345678

76

WIRING DIAGRAM

A

B

-A11

PICTO MODULE

(OPTION)

-A12

BM 5010

OPERATION BOARD

X39: 1

-A10

1

X18:

OVER TEMPERATURE

STEAM GEN.

ELEMENT (PROBE)

-B8

RD

YL

1098761543

X17:

SM 5010

CONTROL BOARD

STEAM GENERATOR

(TEMP PROBE)

-B4

YL

RD

2

PROBE CONDENSER

RD

PROBE OVEN

PROBE BYPASS

-B3

-B5

-B6

RD

YL

RD

YL

1012 1198761543

YL

X16:

X10:

CLEANING PRESSURE SWITCH

CTC

KTM

-B10

GN

WH

C

CABLE CONNECTION SM ON BM CONTROL 500

X19:

1

-W1

12VDC FAN

12VDC IN

12VDC FAN

123456789101112 123

D

RD 18

/2.E3

-G1:12V

TxD

GND

0VDC IN

-G1:0V

/4.E4

/2.E3

IDM (BK)

IDM (WH)

RESET

RxD

-A20:X28:6

-A20:X28:4

-A20:X28:3

-A20:X28:5

-A13:X1:1A8-A13:X1:2A8-A13:X1:3A8-A13:X1:4

A8

/4.E4

DOOR MAGNET SWITCH

CLEANING OPTION ONLY

GN/BU

GN/RD

2

141312 11 10 57986 34

X15:

IDM (BU)

IDM (RD)

/4.E5

-A20:X20:1

/5.A4

-X10:33

-S2

-X10

/2.C7

-X13.5:1

-X13.5:2

+12VDC

GND (M1 H.E. SENSOR)

X11:

4567

-X10

FBS2-6

13

-S7

14

14 13

157

156

/2.C8

-X13.5:3 RD 18

RD 18

GND

RESET

MOTOR SPEED (M1)

X12:

BURNER SUPPLY

8123456

RD 18

32

PRES. SW

LH

RD

RD 18

GND

DOOR SW

L1- 110/120

-X10:31

/2.C4

-B1

BU

BU 18

1

2

LOW LEVEL

HIGH LEVEL

OVEN LAMP

WATER LEVEL PROBE

-A13

IDENTIFICATION MODULE

1098761543

GEN FILL/VALVE

DEHUMIDICATION/VALVE

CONDENSOR/VALVE

7

X14:

PUMP/CLEANING AGENT

COMPARTMENT RINSE VALVE

STEAM GEN OVER TEMP

2

X13:

PUMP/RINSE

STEAM GEN PUMP

10

9 8 7 6 5

4

3 2 1

D5

D4

-A10:X10:12

-A10:X10:11D4-A10:X10:10D4-A10:X10:9

BU

BK

WH

RD

1

3

2

4

A

B

C

RD 18

133

134

-X10

136

D

RD

BK

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

M

1~

-M3.1

COOLING FAN

/2.F4

-X10:20

FBS2-6

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

-X10

-F2.1

1A

21

RD 18

-X10

X1X2

100

-H5.1

21

TITLE

GND

OVEN LAMP CONDENSER

-Y1

A1A2

-Y10

BU 18 BU 18

BU 18

WIRING DIAGRAM

OGB 6.20/10.10

RD 18

A1A2

-Y2 -Y3

DEHUMIDIFICATION

VOLTAGE: WATTAGE: CURRENT:

RD 18

A1A2

STEAM GENERATOR FILLING

120VAC

10.25W

11.7A

LN

-M4

M

1~

BU 18

STEAM GENERATOR PUMP

DRAWN BY

DATE

DRL

7-25-05

FBS2-6

-Y21

A2 A1

WATER CLEANING

DRAWING NO.

SIZE

-Y20

RINSING AGENT

-X10

22

300493

B

RD 18

CLEANING OPTION ONLY

LN

-Y22

CLEANING AGENT

SHEET OF

39

LN

FBS2-6

-Y23

NL

CLEANING AGENT

-X10:23

/5.A1

REV

E

F

A

12345678

77

/5.C3

/6.C3

WIRING DIAGRAM

A

-X10

/2.A6

-U10:12V

-U10:RxC

-U10:RxD

B

-A20

1 2 3 4

C

5 6 7 8 9 10 11 12

87654321

X26: X25: X24: X23:

X27:

GM5010

GAS BOARD

-U10:COM

12V

RECIEVE

TRANSMIT

SIGNAL GND

D

/6.C3

-N21:X1:2

STEAM GEN 1 FLAME OK

0VDC IN

12VDC IN

21

-N21:X1:1

-N20:X1:1

46

/5.C3

-N20:X1:2 BU 18

78456231

GND. FIRING AUTOMAT

CONVECTIO 1 FLAME OK

TxD_12V

GND

RxD_12V

RESET

543678

BU 18

RD 18

X28:

/6.C7

-U21:X2:3

-U21:X2:2

-U21:X2:4

12 10 9111112 910

PHASE ( L1 )

HEAT REQUEST HL1

RESET CONVECTION 1

RESET CONVECTION 1 (HL1)

9

RD 18

78456231 465 132

PWM STEAM GENERATOR

SPEED STEAM GENERATOR

GROUND STEAM GENERATOR

X20:

ALARM CONVECTION 1

910

RD 18

/5.B7

-U20:X2:3

-U20:X2:2

-U20:X2:4

9 8

X22:

7 6 5 4 3 2

1

PWM CONVECTION 1

SPEED CONVECTION 1

GROUND CONVECTION 1

X21:

ALARM STEAM GEN.

ALARM STEAM GEN. (DE)

HEAT REQUEST (DE)

RESET STEAM GEN.

4

RD 18

9

865713218234 765

A

B

C

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

-N20:X1:11

-G1:0V

-G1:12V

-A10:X10:7

-A10:X10:6

-A10:X10:8

-A10:X10:5

/2.E3

/3.D4

-X10:32

/3.D6

/5.C4

-X10

-N20:X1:5

/5.C4 /5.C4

DRAWN BY

DATE

7-25-05

VOLTAGE: WATTAGE: CURRENT:

-N20:X1:10

120VAC

10.25W

11.7A

-X10

DRL

-N21:X1:11

/6.C4

42 434140

-N21:X1:5

300493

B

/6.C4 /6.C4

SHEET OF

REV

A

49

-N21:X1:10

DRAWING NO.

SIZE

E

F

12345678

78

23

-X10

-X10:22 -X10:24

A

WIRING DIAGRAM

/3.D5

-X10:32

-X10

FBS 2-5

-X10:34

33

/6.A4

/6.A1/3.F8

A

BU 18

RD 18

OVER TEMPERATURE THERMOSTAT

B

120VAC

OR 16

BU 16

WH 16

BK 16

-T1

C

D

-X10

E

24 VAC

RD 16

BU 18

61

RD 16

RD 18

60

BU 18

BURNER CONTROL (HOT AIR)

RD 18

STB

(HOT AIR)

-N20

-P1

FLAME SENSOR

HOT SURFACE IGNITION

(HOT AIR)

(GND)

/4.A4

BU 18

3

-R20

(FLAMECHECK)

/4.B4

-X10:46

-A20:X25:10

BU 18

-B7.1

(NEUTRAL)

/4.F6

RD 18

BU 18

2

12

22 21

/4.B6

(HI-LIMIT)

(RESET AIR HEAT/GO)

/4.F6

(RESET AIR HEAT)

(BURNER SUPPLY / 120V)

-A20:X24:3

-A20:X24:1

-A20:X24:2

/4.E5

C

B

-X10:40

(RESET CONV. 1 (HL1)

X1: X2:

-X10:41

-A20:X20:2

GN 18

RD 18

-U20

BURNER FAN

1

-X10

GN 18

101

-U10:GND

/2.C5

RD 18

(HOT AIR)

GN 18

BU 18

123 12345123456 78910 1112

N

L1

GNDGND

X1:

RD 18

BU 18

RD 18

X2:

PWM CONVECTION 1

SPEED CONVECTION 1

GROUND CONVECTION 1

X3:

1

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

59

REV

F

A

12345678

79

/5.A8

-X10:23

-X10

24

A

OVER TEMPERATURE THERMOSTAT

(STEAM GENERATOR)

-B7.2

B

(NEUTRAL)

(GND)

(FLAMECHECK)

BU 18

C

WH 16

120VAC

OR 16

RD 18

/4.A4

BU 16

BK 16

(ALARM STEAM GEN (DE))

/4.F7

/4.B3

-X10:46

-X10:42

-A20:X25:11

WIRING DIAGRAM

/5.A5

-X10:33

(RESET AIR HEAT/GO)

/4.F7

-X10:43

34

(RESET AIR HEAT)

(BURNER SUPPLY / 120V)

/4.E6

-A20:X21:1

(Hi-Limit)

-X10

21

22

(Hi-Limit)

A

B

/4.B5

-A20:X24:9

-A20:X24:8

-A20:X24:7

C

-T2

GN 18

RD 18

24 VAC

-N21

D

RD 16

STEAM GENERATOR BURNER CONTROL

BU 16

123

3

BU 16

45

2

RD 16

67

X1: X2:

RD 16

8910

1

RD 16

11

12

-U21

STEAM GENERATOR BURNER FAN

BU 18

312

12

N

L1

X1:

BU 18

RD 18

345

GND

X2:

D

BU 18

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

PWM STEAM GEN

SPEED STEAM GEN

GROUND STEAM GEN

1

E

-X10

GN 18

103

X3:

GND

GN 18

RD 18

-P2

FLAME SENSOR

RD 18

-R21

HOT SURFACE IGNITION (STEAM GEN)

BU 18

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

2 1

F

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

69

REV

A

1 2 34 5 6 78

80

N

A

L1

B

0

24

C

D

02

4

E

N

1 20 VAC

-F1.

1

2A

2 4 VAC

-T1

TR AN SFOR

M E

R

1 20V

AC

HO

T AI

R

2

12V

4

TR

AN

S

M

I

T

RE

CI

EV

E

3

GN

D

1

-A20:X2

-F1

15A

0

GN

D

L2

L

12V

Rx

D

TxD

CO

M

P2

P1

W

V

U

GN

D

23

36

RD

PO

-S 1

WE

R

MO

-U10 TO

R DR

IV E

6

/8.C

2 4 VAC

-T2

TR AN SFOR

M E

R

1 20V

AC

S T EAM

4

/Y

E

/

W

H

/R

D

SH

W2

V2

U2

N

14

L1

CONTR

O L

D

GN

M 3

~

-Z1

FA

N

U1

/

B

K

V1

/

B

U

W1

/B

N

LINE FIL

TER

-M1

L1

SE N

SO R

9

M O TO

R S

PEE

D M1

CONVEC

TI O N

-BM1

RPM

BK

BN

10

GN

D M1

RD

11

12 V( F

O R SE

NS O

R )

-A10:X1

5

/9.B

5 )

LADDER DI

A G

RAM

A

B

C

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

1 2 34 5 6 78

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

79

REV

F

A

1 2 34 5 6

81

N

0

12 V

A

D C

12

L1

B

C

LADDER DI

D

A G

RA M

E

78

N

P

1

O

90

2V

N

W

0V

12V

GN

D

CO

-A10:X1

NT

/9.D

RO

X3

12

X1

X2 :

L BO

A R D

54

3

21

3

0

2

3

PO

FAN

WE

HO

-U20

R BU

CONTR

T AI

R

RN

O

ER

L

:

1

X24

6

5

3

2

4

R

GN

T x

ESE

D

_ 12V

T

1

AIR

T

HO

OUND

1

R 1

AI

1

R

AI

GR

T

HO

M

PW

T

D HO

EE

SP

1

X28

12V

Rx

0 V

D_

DC

12

IN

V

X20

DC I

N

1

(HL1)

1

R

T HL1

R

X25

K

O

E

M

T

A

M

O

T

U

(GM)

-A2

0

GA S BO

AR D

3

2

1

:

PO

FAN

WE

-U21

STE

R BU

CONTR

A M

RN

O

ER

L

X1

54

X2

3

:

21

:

X3

1

7

R

O

T

A

R

E

N

E

G

M

STEA

ND

OU

8

R

O

T

RA

NE

E

9

R

M G

O

RAT

E

N

M GE

GR

EA

ST

M

PW

A

E

T

S

PEED

S

X21

X25

K

O

T

A

EN.

G

EN.

G

)

(DE

T

(DE)

.

D

E

M

A

L

M

O

T

U

-

DC

E

2 64

R SU

V A

PP

C

L Y

1 )

L

(

PHASE

I

T A

O

ESET H

R

I

T A

O

ESET H

S

A

S

M GEN.

E

A

R

E

QU

EAT RE

H

T AI

M HO

R

ALA

T AI

O

H

M

R

ALA

L

F

HOT AIR 1

GND. FIRING

12V

T

I

SM

AN

TR

E

EV

CI

RE

D

GN

M

A

E

T

ESET S

R

M

A

E

T

ESET S

R

E

U

Q

RE

EAT

H

A

E

ST

M

R

ALA

AM GEN

E

ST

M

R

ALA

S

T U

9 NO

6-

N. F

GE

M

A

STE

GND. FIRING

L

X20

X25

X26

X21

X25

-G1

L1

)

D

R

BOA

OL

TR

ON

C

(

11:8)

X

:

A10

-

(

32

:

0

1

-X

5

.C

/9

X1 :

( L1 )

E

AS

1

2

3

4

5

6

10

9

2

4

3

1

2

3

4

5

6

9

11

9

1

-B7.

MO

-U10:X1 TO

R DR

2

IV E

2

21

22

/7.C

5

21

22

-B7.

12

11

10

9

8

7

6

5

4

3

2

1

X1 :

12

11

10

9

8

7

65

4

3

2

1

PH

T

HEA

R

I

A

T

ESE

O

t

i

t

i

L

D

t

i

t

i

L

D

R

G

/

T

A

E

H

ESET AIR

R

-L

UT

1

L

AT

G

/

-L

UT

Hi

NE

ECHECK

AM

(

E

HE

AT

E

-N21

Hi

NE

ECHECK

AM

L

AS

CONTROL

-N20

MO

F

D U L

E

H

P

ESET AIR

R

H

CONTROL

MO

F

D U L

E

im

RA

GN

)

O

im

RA

GN

-P FL

SE

1

AM

NS

E

OR

X2

HO

3

2

1

T AI

R BU

VA

RN ER

X2

31

2

ESET AIR

R

ST

LV E

GAS

SE NS OR

FL AM

E

EA M

BU RN ER

VA LV

GAS

E

HOT S

IGNIT

URF

E R

A C E

1

-P 2

1

HOT S

URFA

C E IG

N I

T O R

-R20

2

-R21

2 4 VAC

N

120 V

A C

L1

0

24

0

24

A

B

C

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

1 2 34 5 6 78

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

89

REV

F

A

1 2 34 5 6 78

82

N

-Y2

3

-Y2

2

0

-Y 2

-M4

-Y

-Y 1

3

-Y2

1

M

(GAS BO

/8.D

-A20:X2 4

A R

0

D

-X1

:

1

)

0 :

3 2

A

B

-H5.1

X2

X1

-F2.

1

2

1

-A1

3

4

3

I.D. MO

D U L E

2

0

12 VD

C

12

L1

5

/8.D

4

(GAS BO

-A20:X2

6

-M3.1

A

R

D

)

8

3

5

A

B

M

1

LADDER DI

C

D

7

6

5

4

3

2

1

0

L2

8

9

81

9

L1

X14

:

10

PU MP / C

L EAN

A G E N T

6

3

4

57

C

PUMP / RI

O MPAR

TMEN

N S E

T R

X13

I

NS

:

E V

.

2

STEAM GEN

OVER

T E M

P

E

8

1

STEAM GEN

PUM

P

H I

G H L EVEL

1

BU

H

W A

TER

L EVEL

P R

O B E

6

7

B URNE

R S

U P P L Y

-B 1

X11

:

L O

PR

DOOR S

W

ES. S

L EVEL

GN

W

D

5

4

3

2

RD

L

14

13

45

MOTOR

SEN

SOR

SPEED

GND R ESE

GN

M

D

T

1

10

86

7

9

14

13

-S

2

W

I

T

C

H

-S

7

1

3

2

12v

( F

OR S

EN

X15

S O R

:

)

14

12

11

13

/7.C

-M1

3

O

N

O

N

L

Y

ESSU

RE

S

W

I

T

CH

S

DOOR MAGNET

6

5

7

CONDE

DEHUMIDICATION

G E N F I

L

NS

L /

VAL

OR/V

VE

A L V

/

V

E

A L V E

5

4

3

2

1

GN

/B U

GN

GN /R D

-B1

0

KTM

CTC

CLEANING OPTI

C

L

EAN

IN

G PR

2

4

3

OVEN

HOT A

STEAM GE

L

I

R

AM

P

N

X12

:

10

87

6

9

RD

YL

RD

YL

WH

-B

-B 5

6

PR

OBE BYPAS

OBE OV

E N

S

1

L1-

110/120 V

A

C

I

N P U T

X16

:

12

11

RD

YL

-B 3

PR

OBE C

O N D E N S E R

11

12

IDM (

ID

M (B

M (RD)

W

U)

H

10

9

ID M (BK

)

STEAM GEN

E R A T O R

7

8

R

T x

ESE

D _ 12V

T

3

2

1

YL

RD

YL

-B

-B 8

4

EL

(TEMP PR

EMEN

T (PR

OBE

O

)

B E )

6

Rx D_ 12 V

X10

:

4

RD

OVER

STEAM GEN.

TEMPER

AT URE

4

5

0V DC

GN

I N

D

87

6

5

(OPTIO

N)

3

12V

DC I

N

X17

:

9

MOD

U L E

1

2

12V

DC FA

N

(

-

+

)

X18

:

10

CONTROL B

-A1

SM 5

0

010

O A R D

X19

:

1

A G

RA M

X39:

1

OPER

BM 5

-A1

ATION M

1

-A1

PIC

2

T O

O DULE

010

C

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

1 2 34 5 6 78

TITLE

WIRING DIAGRAM

OGB 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

7-25-05

DRAWING NO.

SIZE

B

300493

SHEET OF

99

REV

F

A

CLEVELAND RANGE OGS 6.20/10.10

83

SEQUENCE OF OPERATIONS

When using these instructions refer to the OGS 6.20/10.10 wiring schematic.

1 When 120 VAC is applied to the combi, it is sent through the line filter (Z1) to the

Power Control Switch (S1).

2 When the Power Control Switch (S1) is closed

a The red light in the switch is energized. b 120 VAC is sent through the 7 amp fuse (F10) to terminal 1 of connector X11 on

the Motor Drive (U10)

c 120vac is sent through the 2 amp fuse (F1.1) to

• The primary of the Hot Air 24v Transformer (T1) ◊ 24 VAC is sent from the secondary of the transformer to the Hot air

Burner Control (N20)

• The primary of the Steam 24v Transformer (T2) ◊ 24 VAC is sent from the secondary of the transformer to the Steam Burner

Control (N21)

• To terminal 12 of connector X1 on the Hot Air Burner Control (N20)

• To terminal 12 of connector X1 on the Steam Burner Control (N21)

• The 12 VDC Power Supply (G1) ◊ 12 VDC is sent to terminals 1 and 2 of connector X20 on the Gas Board

(A20)

◊ 12 VDC is sent to terminal 3 and 4 of connector X10 on the Control Board

(A10)

• To terminal 2 of connector X1 on the Hot Air Power Burner and Fan Control (U20)

• To terminal 2 of connector X1 on the Steam Power Burner and Fan Control (U21)

• To terminal 1 of connector X12 on the Control Board (A10)

d With 120 VAC to the Control Board (A10) The Operation Board (A11) is

energized

• An alarm will sound for one second

• All the LED’s and the display will energize one at a time.

• “STARTING” will be displayed for 3 seconds

• “Please wait” will be displayed

• The international model number will be displayed

• The time and date will be displayed and this will continue until the on/off

switch is depressed.

3 When the ON/OFF is depressed with the combi in the steam mode

a The display will show the set temperature and set time.

4 With the combi in the steam mode with time on the timer, the door closed and the

start switch is depressed a The front display will include a lighted bar under the steam symbol

• When the heat circuit is energized the heat symbol will be energized

84

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

b The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6, and 7 on connector X10 to connector X12 on the Motor Drive Board (U10).

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 240 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

c Hot air heat circuit is energized

• A signal is sent from terminal 8 of connector X15 on the Control Board (A10) to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower.

◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of connector X15 on the Control Board (A10)

• A request for heat is sent from terminal 3 of connector X12 on the Control Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module (N20) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 12 of connector X15 on the Control Board (A10)

• The heat circuit will remain energized until the cabinet set temperature is reached as sensed at probe B6.

d The steam circuit is energized

• 120 VAC is sent from terminal 4 of connector X12 on the Control Board (A10) to the coil of the Y3 solenoid allowing water to be thrown against the element until the bypass probe (B5) senses 183 degrees F.

◊ NOTE: If the set temperature is above 212 degrees F the hot air circuit

will be energized (after the by pass probe is satisfied) until the compartment setting is reached.

e When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

f When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

5 With the combi in the Hot Air mode with time on the timer, the door closed and the

start switch is depressed

a The front display will include a lighted bar under the Hot Air symbol

85

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

c The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6, and 7 on connector X10 to connector X12 on the Motor Drive Board (U10).

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 240 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

• NOTE: If the set temperature is less than 212 degrees F than fan will be

pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).

b Hot air heat circuit is energized

• A signal is sent from terminal 8 of connector X15 on the Control Board (A10) to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower.

◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of connector X15 on the Control Board (A10)

• A request for heat is sent from terminal 3 of connector X12 on the Control Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module (N20) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 12 of connector X15 on the Control Board (A10)

• The heat circuit will remain energized until the cabinet set temperature is reached as sensed at probe B6.

c When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

d If the “Crisp and Tasty” mode is selected

• 120 VAC is sent from terminal 6 of connector X12 on the Control Board (A10) to the Dehumidification Valve (Y2) to pull the humidity out of the cabinet down the drain. ◊ In the light and medium modes (one and two drops in the display) the Y2

valve will be energized until the bypass probe (B5) is satisfied.

◊ In the full mode (3 drops in the display) the Y2 valve will be energized

continuously.

e When the timer counts to 0 or the core temp probe (B10) reaches the set amount

86

the cycle .

5 With the combi in the Combi mode with time on the timer, the door closed and the

start switch is depressed a The front display will include a lighted bar under the Combi symbol

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

b The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6, and 7 on connector X10 to connector X12 on the Motor Drive Board (U10).

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 240 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

c Hot air heat circuit is energized

• A signal is sent from terminal 8 of connector X15 on the Control Board (A10) to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower. ◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of connector X15 on the Control Board (A10)

• A request for heat is sent from terminal 3 of connector X12 on the Control Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module (N20) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 12 of connector X15 on the Control Board (A10)

• The heat circuit will remain energized until the cabinet set temperature is reached as sensed at probe B6.

d The steam circuit is energized.

• 120 VAC is sent from terminal 4 of connector X12 on the Control Board (A10) to the coil of the Y3 solenoid allowing water to be thrown against the element until the bypass probe (B5) senses 183 degrees F.

• The heat circuit will remain energized until the cabinet set temperature is reached

• If the bypass probe (B5) drops below the set level the steam circuit will start again.

e When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

87

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

f If the “Crisp and Tasty” mode is selected

• 120 VAC is sent from terminal 6 of connector X12 on the Control Board (A10) to the Dehumidification Valve (Y2) to pull the humidity out of the cabinet down the drain.

◊ In the light and medium modes (one and two drops in the display) the Y2

valve will be energized until the bypass probe (B5) is satisfied.

◊ In the full mode (3 drops in the display) the Y2 valve will be energized

continuously.

g When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

5 With the combi in the Rethermalization mode with time on the timer, the door closed

and the start switch is depressed a The front display will include a lighted bar under the Retherm symbol

• When the heat circuit is energized the heat symbol will be energized

• The cooking mode symbol will be energized.

• The time display will invert and begin to count down.

b The fan circuit is energized by the Control Board (A10) transmitting and

receiving a signal from terminals 5,6,7 and 8 on connector X10 to terminals 3,4,5 and 6 of connector X28 on the Gas Board (A20)

c The Gas board (A20) Transmits a signal from terminal 4 of connector X26 to the

Motor Drive.

• The motor Drive Board sends a signal through the thermal switch in the motor from Terminal 5 and receives on terminal 6

• If the thermal switch is not open the Motor Drive Board (U10) sends 220 VAC 3 phase to the motor.

• The motor reverses direction every 120 seconds with a 15 second coast.

• NOTE: If the set temperature is less than 212 degrees F than fan will be

pulsed on for 2 seconds every 60 seconds after the cabinet set temp (B6).

d Hot air heat circuit is energized

• A signal is sent from terminal 8 of connector X15 on the Control Board (A10) to terminal 4 of connector X2 on the Hot Air Power Burner and Fan Control (U20) selecting the set speed of the combustion blower.

◊ When this speed is attained the signal is sent from terminal 2 of connector

X2 on the Hot Air Power Burner and Fan Control (U20) to terminal 2 of connector X15 on the Control Board (A10)

• A request for heat is sent from terminal 3 of connector X12 on the Control Board (A10) to terminal 10 on connector X1 on the Hot Air Control Module (N20) ◊ 24 VAC is sent from terminal 2 of connector X2 on the Hot Air Control

Module (N20) to the hot surface igniter (R20).

◊ The gas valve is energized allowing gas and air into the burner chamber to

be ignited by the hot surface igniter.

◊ The Hot Air Burner Control Module (N20) senses at least 1.5 micro amps

88

DC from the flame sensor (P1) at terminal 3 of connector X2 and sends a signal from terminal 2 of connector X1 to terminal 12 of connector X15 on the Control Board (A10)

• The heat circuit will remain energized until the cabinet set temperature is reached as sensed at probe B6.

e The steam circuit is energized.

• 120 VAC is sent from terminal 4 of connector X12 on the Control Board (A10) to the coil of the Y3 solenoid allowing water to be thrown against the element until the bypass probe (B5) senses 183 degrees F.

• The heat circuit will remain energized until the cabinet set temperature is reached

f If the bypass probe (B5) drops below the set level the steam circuit will start again g When the condensate box is heated to 140 degrees F at the B3probe, 120 VAC is

sent from terminal 5 of connector X12 to the condenser valve (Y1) until the temperature drops.

h When the timer counts to 0 or the core temp probe (B10) reaches the set amount

the cycle ends and the steam generator reverts to the standby temperature of 190degree F.

89

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

TITLE

WIRING DIAGRAM

OGS 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

8-9-05

DRAWING NO.

SIZE

B

300494

SHEET OF

16

REV

A

12345678

90

A

CONTROL POWER

-S1

6

5

RD

4

BK 12 BU 12

L1

N1

-Z1

LINE FILTER

B

L

N

GND

GR

BU 12

BK 12

C

-X10

1

2

3

L1

N

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

BK 12 BU 12

3

2

1

-F1.1

20

-X10

BU 18

102

-X10

GND

-X10

2A

-X10

G

96-264V AC

N

30

BK 12

12

RD 18

31

RD 18

RD 18L

POWER SUPPLY 12VDC

-A10:X12:1

/3.D6

-G1

12V DC

0V

12V

BU 18

RD 18

-X13.1

-X13.2

-A10:X10:3

-U10:X12:1

-A10:X10:4

/A6

/3.D4

/3.F1

-X10:21

BL 12

A

/E3

/3.B3

-G1:12V

-A10:X10:7

-A10:X10:6

-A10:X10:5

-F10

15A

2 1

B

RD 18

BU 18

RxD

VUGND W

OR

P1 P2

TxD

COM

BK 18

BU 18

L2L1

BN

/3.B5

/4.A6

/3.B5

-X10:42

-A10:X15:9

-A10:X15:11

C

/4.E5

-X10:101

-U10

MOTOR DRIVE

GN 18

-W2 CABLE

12V

BK

GR

D

BK 18

5

4

6

5

4

6

SH

GND

M 3~

TW/GY

U1/BK

V1/BU W1/BN

FAN

TW/GY

-M1

W2/YE

V2/WH

U2/RD

219

91237

873

8

-X13.5

-X13.6

-BM1

RD 18

BU 18

RD 18

3

2

1

3

2

1

BN

BK

RD

RPM

E

PRELIMINARY

WIRING DIAGRAM

TITLE

WIRING DIAGRAM

OGS 6.20/10.10

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

8-9-05

DRAWING NO.

SIZE

B

300494

SHEET OF

26

REV

A

F

12345678

91

WIRING DIAGRAM

A

B

-A11

PICTO MODULE

(OPTION)

-A12

BM 5010

OPERATION BOARD

X39: 1

-A10

1

X18:

1098761543

X17:

SM 5010

CONTROL BOARD

PROBE CONDENSER

RD

2

PROBE OVEN

PROBE BYPASS

-B3

-B5

-B6

YL

RD

YL

RD

YL

1012 1198761543

X16:

X10:

CLEANING PRESSURE SWITCH

CTC

KTM

-B10

GN

WH

C

CABLE CONNECTION SM ON BM CONTROL 500

X19:

1

-W1

12VDC FAN

12VDC IN

12VDC FAN

123456789101112 123

D

RD 18

/2.E3

-G1:12V

TxD

GND

0VDC IN

-G1:0V

/2.A6

/2.E3

-U10:GND

IDM (BK)

RxD

-U10:TxD

/2.A6

IDM (WH)

-U10:RxD

-A13:X1:1A8-A13:X1:2A8-A13:X1:3A8-A13:X1:4

A8

/2.A6

DOOR MAGNET SWITCH

CLEANING OPTION ONLY

GN/BU

GN/RD

2

141312 11 10 57986 34

X15:

IDM (BU)

IDM (RD)

-S2

-X10

/4.C3

/2.C7

-X13.5:1

-N20:X1:2

+12VDC

FLAME OK (HOT AIR)

X11:

4567

-X10:42

GND (M1 H.E. SENSOR)

13

-S7

14

14 13

157

156

/2.C8

-X13.5:3

MOTOR SPEED (M1)

RD 18

-U20:X2:4

GND

PWM (HOT AIR)

X12:

BURNER SUPPLY

8123456

-X10:33

/4.A4

PRES. SW

RD 18

GND

DOOR SW

L1- 110/120

-X10:31

/2.C4

N.O. COM

/4.B6

-U20:X2:2

1

2

PRES. SW

FANE SPEED

HEAT REQUEST

OVEN LAMP

-X10:41

/4.B4

-S2

INJECTION PRESSURE SWITCH

INJECTION

DEHUMIDICATION/VALVE

CONDENSOR/VALVE

7

1098761543

X14:

RESET

PUMP/CLEANING AGENT

PUMP/RINSE

COMPARTMENT RINSE VALVE

/4.C4

-N20:X1:11

RESET

/4.C4

-N20:X1:5

2

ALARM GAS

X13:

/4.B4

-X10:41

-A13

IDENTIFICATION MODULE

10

9 8 7

ALARM GAS

6 5

4

3 2 1

D5

D4

-A10:X10:12

-A10:X10:11D4-A10:X10:10D4-A10:X10:9

BU

BK

WH

RD

1

3

2

4

A

B

C

RD 18

133

134

-X10

136

D

RD

BK

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

M

1~

-M3.1

COOLING FAN

/2.F4

-X10:20

FBS2-6

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

-X10

-F2.1

1A

21

RD 18

-X10

X1X2

100

-H5.1

21

TITLE

GND

OVEN LAMP CONDENSER

-Y1

A1A2

-Y10

BU 18 BU 18

BU 18

WIRING DIAGRAM

OGS 6.20/10.10

RD 18

A1A2

-Y2 -Y3

DEHUMIDIFICATION

VOLTAGE: WATTAGE: CURRENT:

INJECTION

120VAC

10.25W

11.7A

RD 18

A1A2

-Y21

A2 A1

WATER CLEANING

CLEANING OPTION ONLY

LN

-Y22

LN

E

-Y23

-Y20

DRAWN BY

DATE

DRL

8-9-05

FBS2-6

DRAWING NO.

SIZE

RINSING AGENT

-X10

22

300494

B

CLEANING AGENT

FBS2-6

PRELIMINARY

SHEET OF

36

NL

CLEANING AGENT

/4.A1

-X10:23

REV

F

A

12345678

92

-X10:22

-X10

/3.F8

23

A

BU 18

RD 18

OVER TEMPERATURE THERMOSTAT

STB

(HOT AIR)

B

120VAC

(GND)

OR 16

BU 16

WH 16

-T1

C

RD 16

BK 16

A7

24 VAC

RD 16

BU 18

-N20

D

BU 18

RD 18

BURNER CONTROL (HOT AIR)

3

WIRING DIAGRAM

/3.D6

-A10:X11:8

33

-X10

-B7.1

22 21

/3.A7

/3.D6

(NEUTRAL)

(HI-LIMIT)

(FLAMECHECK)

/3.B5

-X10:42

-A10:X15:12

BU 18

2

(HI-LIMIT)

/3.A7

-A10:X14:2

(RESET CONV. 1 (HL1)

RD 18

X1: X2:

1

-X10

(RESET AIR HEAT)

-A10:X14:1

(BURNER SUPPLY / 120V)

-A10:X12:3

/3.A7

41

-A10:X14:3

RD 18

-U20

BURNER FAN

(HOT AIR)

A

/3.B5

/2.C7

C3

-X13:5:2

-N20:X1:1

-A10:X15:10

42

-X10

/3.A6

-A10:X15:2

-A10:X15:8

B

C

GN 18

RD 18

BU 18

123 12345123456 78910 1112

N

L1

GNDGND

X1:

RD 18

BU 18

RD 18

X2:

D

E

F

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

-X10

61

60

BU 18

TITLE

RD 18

HOT SURFACE IGNITION

WIRING DIAGRAM

OGS 6.20/10.10

-P1

FLAME SENSOR

(HOT AIR)

-R20

-X10

VOLTAGE: WATTAGE: CURRENT:

GN 18

101

-U10:GND

120VAC

10.25W

11.7A

/2.C5

GN 18

DRAWN BY

DATE

DRL

8-9-05

X3:

1

DRAWING NO.

SIZE

SPEED CONVECTION 1

B

PWM CONVECTION 1

GROUND CONVECTION 1

300494

PRELIMINARY

SHEET OF

46

REV

E

F

A

RD 18

12

12345678

93

A

/6.A6

-A10:X15:2

/6.B5

-A10:X15:8

/6.B5

B

-A10:X15:11

-A10:X15:9

C

D

FAN

PTC

X11:

5

V

PTC

W X10:

X12:

L

NPE

1

23

15A

SCH

U

PE

GND TxD RxD

12V

4 3 2

1

2A

1

3 4

12

GND RECIEVE TRANSMIT

RESET AIR HEAT/GO

NEUTRAL

Hi-Limit Hi-Limit

RESET AIR HEAT

PHASE ( L1 )

IRM

1

2

3

6

4

1234567

89101112

A

B

C

D

E

F

LADDER DIAGRAM

THIS DESIGN DESCRIBES A PROPRIETARY ITEM AND IS THE PROPERTY OF CLEVELAND RANGE.

THIS DRAWING IS NOT TO BE COPIED OR USED WITHOUT THE APPROVAL OF CLEVELAND RANGE.

LINE FILTER

CLEVELAND RANGE, LLC

1333 East 179th St., Cleveland, Ohio 44110-2574

12345678

GND

RD

90-264VAC

N

TITLE

WIRING DIAGRAM

OGS 6.20/10.10

POWER SUPPLY

12VDC

VOLTAGE: WATTAGE: CURRENT:

120VAC

10.25W

11.7A

DRAWN BY

DATE

DRL

8-9-05

DRAWING NO.

SIZE

300494

B

12

12VDC

0

PRELIMINARY

SHEET OF

56

REV

A

E

N L1

F

Cleveland Range OGB-6.20, OGB-10.10, OGS-6.20, OGS-10.10 User Manual

Table of Contents

INSTALLATION INSTRUCTIONS

MODEL: c OGB-10.10

MODEL: c OGS-10.10

MODEL: c OGB-6.20

MODEL: c OGS-6.20

DESCALE STEAM GENERATOR