Page 1
Operator’s Manual
a
)
Use and Care Instructions
Gas Convection Rotisserie and Holding Oven
Models: CR32, CR32-DD, CR32-FP, CR32-FFP
CR28, CR28-DD, CR28-FP, CR28-FFP (CR32 Shown
1333 East 179th Street
Cleveland, Ohio 44110
Phone: (216) 481-4900
F
x: (216) 481 3782
Part No. CR-OPM REV. A 06/01
Page 2
FOR THE USER
FOR YOUR SAFETY
WARNING:
Do not store or use gasoline
or other flammable vapors or
liquids in the vicinity of this or
any other appliance.
Improper installation, adjustment,
alterations, service or maintenance can
cause property damage, injury or death.
Read the installation, operating and
maintenance instructions thoroughly
WARNING
Disconnect power before servicing
before installing or servicing this
equipment.
IMPORTANT
IT IS IMPORTANT, TO POST INSTRUCTIONS, WHICH ARE TO BE
FOLLOWED IN THE EVENT THE USER SMELLS GAS. THESE
INSTRUCTIONS SHOULD BE LOCATED IN A PROMINENT LOCATION, AND
BE FULLY UNDERSTOOD BY ALL USERS OF THIS EQUIPMENT. THIS
INFORMATION SHOULD BE OBTAINED FROM YOUR LOCAL GAS
SUPPLIER.
ALL SERVICE MUST BE PERFORMED BY A QUALIFIED CLEVELAND
RANGE AUTHORIZED TECHNICIAN.
Each oven is equipped with a 120V/15A-power cord, with a three-prong (grounding) plug for
protection against shock hazard. It should be plugged directly into a properly grounded threeprong receptacle. Do not cut off or remove the grounding prong from the plug.
Clearances specified for the oven on the rating label are required for the proper cooling,
ventilation, and combustion air supply. Make sure nothing obstructs the flow of combustion and
ventilation air. Depending on the number of units being installed, make sure there is enough
clearance between each unit, and from walls to the sides and to the rear.
In the event of a power failure, no attempt should be made to operate the appliance during the
power failure.
If the appliance is mounted on a moveable stand or warmer, and if it is moved for cleaning or
service, make sure the restraint is reconnected after the appliance has been returned to its
installed position.
RETAIN THIS MANUAL FOR YOUR REFERENCE
Page 3
Operator’s Manual
More SAFETY
Information
WARNING:
DEATH, INJURY OR EQUIPMENT DAMAGE
may result from an improperly adjusted gas
control and ignition system. Do not alter any
adjustments on this oven’s electronic control or
gas valve. If adjustment is required, contact an
authorized service center. Cleveland Range is
in no way responsible for the operation or safety
of this equipment if the controller, valve, or
igniter probe are adjusted by anyone other than
a Cleveland Range authorized service agent.
Lighting and Shutdown
DO NOT TRY TO LIGHT THE BURNERS WITH A
FLAME.
THE BURNERS ARE SELF-IGNITING.
Lighting Instructions
The following START-UP SUMMARY is for quick
reference ONLY. For safe operation and use of
this equipment, the operator should comply with all
safety instructions and operating instructions in this
manual. The oven and fireplace (if equipped) has
an electronic ignition system which automatically
ignites the burner, senses the flame and controls
the gas flow. This provides precise burner control,
safety ignition, and shutdown.
OPERATOR’S MANUAL
ROTISSERIE OVEN
CONTENTS:
Safety Precautions………..……………… 1
Features…………………………………… 2
Daily Startup… …………………………… 4
Oven Loading……………………………… 5
Cooking……………………….……………. 6
Co-Cook……………………….…………… 6
Holding…………..…………………………. 7
Unloading………………………………….. 7
Ensure Uniform Cooking……….………… 8
Problem Messages / Alarm……..……….. 8
Daily Cleaning/Maintenance…………….. 9
Programming, Troubleshooting &
Technical Information
Control Panel…………………………….… 11
Programmer’s Worksheet………………… 13
Programming Tips & Techniques………… 14
Menu Item Programming…….……………. 15
Co-Cook Programming………………….… 17
System Programming……………………... 18
Troubleshooting……………………..…...… 19
Error Messages……………………….……. 20
1. Turn ON the POWER switch
• The controller will display “SYSTEM INIT”
• The controller will then display “PREHEAT”
XXX°F” and the blower will start
• The oven burner will attempt to light.
• If no ignition occurs the system will
automatically lock out and a buzzer will
sound
2. The controller may be reset manually by
turning the POWER switch to the OFF position
for 5 minutes then back to ON.
3. The fireplace (if equipped) will light only after a
cooking program has been started.
Shutdown Instructions
Turn the POWER switch to the OFF position. The
oven burner and fireplace burner (if equipped) will
be immediately extinguished.
1 Cleveland Range, Inc.
Page 4
FEATURES OF THE ROTISSERIE OVEN
Operator’s Manual
The Cleveland Range rotisserie oven is a high
capacity, gas fired oven, ideal for producing
perfectly cooked, delicious, and appealing meats
and other foods.
The oven combines several cooking and
processing techniques, including:
• Temperature-controlled oven cooking
• Variable speed Rotisserie spit cooking
• Convection oven cooking
• Infra-red browning
• Moisture control venting
Other performance features:
• Heavy-duty rotating spit system, with:
− Choice of removable spits
− Optional load handling tools
− Spit transport cart
• High capacity, water-filled drip pan
• Easy-cleaning surfaces inside and out
• Large viewing window and lighted interior
• 2 door option for easy loading and
unloading
• Gas fireplace option, either in
the operator’s door or in back
of unit to provide the
appearance of cooking over an
open flame
Oven Controller – The oven is
equipped with a programmable
cooking controller that can hold up
to 16 cooking programs, with up to 3
stages in each program, plus hold/warm.
This allows you to specify the exact cooking times
and temperatures you desire to prepare any food.
Once set up, these programs will produce perfectly
repeatable results every time.
DRUM
AND SPITS
Rotisserie and Spits – Up to 7 or 8 spits can
be installed into the rotisserie oven (depending on
model). If fewer are used, they should be installed
so they are balanced around the drum.
A few spits are available for different loads:
• The standard model is the axial “V” spit, used for
spitting chicken and similar items. Chicken
should be trussed with string to keep it secure.
There are two versions of the “V” spit, a long ”V”
for bigger chicken and a short “V” for smaller
chicken.
• Another useful spit is the “basket”. This is
used for roasting product which cannot be
easily secured to an axial spit, such as turkey
breasts, hams, spareribs, etc.
CONVECTION
FANS
ROTISSERIE
ADVANCE
BUTTON
VENT
OVEN
CONTROLLER
POWER
SWITCH
WATER-
FILLED
DRIP PAN
GAS
BURNER
Other controller features:
• Precise temperature control
• Alphanumeric status display
• Programmable rotating speeds
• Load-adaptive temperature control
AXIAL
“V” SPIT
As the operator, you should not need to program
the oven controller. The program should be set up
by the chief cook or chef.
Menu Item Buttons – There are 16 Menu Item
buttons that start cooking programs. Details about
the menu item buttons, cooking program
parameters, and programming procedures are
provided later in this manual.
BASKET SPIT
Rotisserie Oven 2
Page 5
Operator’s Manual
More: Rotisserie Operating Features
Infrared Gas Burner – The burner provides
heat for both convection cooking and infrared
browning. The controller can power the burner at
“high heat” (60,000 BTUH) or “low heat” (48,000
BTUH), accommodating different load sizes and
browning needs.
Oven Vent
center of the oven. This vent is operated by the
controller and can be programmed within each
cooking stage to 1) open and close to regulate the
temperature, or 2) to remain closed, while the
burner is turned on and off to regulate the
temperature.
– There is a vent located in the top
NOTE: National Codes Require That a
Ventilating Hood Must be Installed
gas burner produces combustion gases which
must be vented to the outside. The entire oven
must be placed under the ventilating hood.
Be sure to turn on the powered ventilating hood
every time before you start the oven.
Convection Fans
fans located inside the top of the oven. The fans
continuously circulate the hot air in the oven in
every cooking stage. The fans are pulsed during
the hold/warm stage to eliminate any drying factor.
Convection cooking produces an even, consistent
heat in the entire oven cavity and speeds up the
roasting process over a conventional oven.
– There are 2 circulating
– The
Preheat Mode – When you first turn on the
oven, the controller ignites the burners to bring the
oven to its pre-programmed PREHEAT
temperature of 300°F. (The Preheat temperature
can be changed. See System Level Programming
later in this guide.)
Ready Mode – After the Preheat mode is
complete, the controller holds the oven in the
READY mode. In this mode the Preheat
Temperature is maintained for 20 minutes in
readiness for you to load the oven with the product
to be cooked.
Standby Mode – After the oven has reached
the READY temperature, the controller waits for
you to load the spits and press the desired Menu
Item button. If no button is pressed for 20 minutes,
the controller enters the STANDBY mode, in which
the oven temperature is “setback” for energy
savings, and held there until you are ready to
again preheat the oven. The pre-programmed
Standby temperature is 200°F (the Standby
temperature can be changed. See System Level
Programming later in this guide). Touching any
button takes the unit out of Standby mode and
back into Preheat mode.
Cooking Mode - After preheating and loading,
a cooking cycle is started by pressing the desired
Menu Item button. The button light will flash during
cooking. At the cycle’s end, an alarm will sound
and the controller will enter the Hold/Warm mode.
Rotisserie Advance Button – This feature
allows you to manually activate (“jog”) the
rotisserie motor while the oven door is open.
Jogging brings to the front of the oven each
rotisserie spit position for easy loading or
unloading.
Gas Fireplace (if equipped) – This feature
provides the appearance of cooking over an open
flame. A fireplace switch allows it to be turned off
or operate automatically. In the automatic mode,
the fireplace turns on whenever one of the 16
cooking programs is operating. If the fireplace only
is desired for ambience, item 16 is preprogrammed to operate the fireplace without the
main burner.
3 Cleveland Range, Inc.
Hold/Warm Mode – After the cooking cycle
ends, the oven automatically goes into the
Hold/Warm Mode. Typically the hold temperature
is 175°F (but you can program a different hold
temperature at the system level). The rotisserie
speed is reduced to 1 rpm. The alphanumeric
display shows the total time the product has been
holding and continues counting up. After 2 hours,
the alarm tone sounds, indicating the product can
no longer be held warm safely.
Page 6
Daily Startup Procedure – perform every day before using the oven.
Do not load any food into the oven unless it has been cleaned,
inspected, filled with water and PREHEATED.
1. Prepare Oven
Each day, before starting up the oven, prepare it
for the day’s cooking.
The oven must be clean before starting. (It should
be cleaned at the end of each day, per procedures
given later in this guide.) Make sure the oven
window is clean – use a mild detergent or an
approved glass cleaner. (Also, make sure the
fireplace glass is clean in fireplace models – use
razor blade scraper supplied.)
If not done the previous night, before starting the
oven, we recommend you spray all interior
stainless steel surfaces, including inside of the
rotisserie drums, jet plate, and convection fans,
with Jef-Guard or another oven coating: this will
make cleaning the oven much easier at the end of
the day. DO NOT SPRAY BURNER SURFACE.
In single-door models, a hanging metal burner
shield is installed inside the oven for use during
spraying. This must be lifted to cover the burner
while the interior of the oven is sprayed with the
protective coating. Make sure this shield is used
every time the oven interior is coated. (Two-door
models are supplied with a loose shield for this
same purpose.)
Inspect the oven to make sure all interior parts are
in good working order and in place. Make sure
the “jet plate” (which guides the convection air)
is NOT hanging down but is in its normal
position. (See the drawing in Operator’s Daily
Cleaning/Maintenance section of this manual.)
Make sure the oven is located the minimum
required distance from other equipment and
walls. There must be a minimum clearance of 3
inches on each side and 3 inches at the back.
(Two door models require 36 inches rear
clearance, except for hearth installations, where
back of unit may be in contact with noncombustible hearth wall opening.)
2. Fill Drip Pan with Water
There is a drip pan at the bottom of the oven. The
water in this pan has two functions: 1) it helps keep
oven moisture at a constant level, and 2) it catches
food drippings, keeping them from burning onto the
bottom surface of the oven.
The pan must be drained at the end of every
cooking day and refilled at the beginning of the
next cooking day. (Refer to Daily
Cleaning/Maintenance later in this guide for
cleaning instructions.)
The drip pan holds 3 gallons of water. Use fresh
water at the beginning of each day. Before filling
the pan, make sure the drain valve located below
the oven is closed.
Operator’s Manual
3. Preheat Oven
Make sure the door is closed, then turn the oven
power ON. The oven controller first displays
“SYSTEM INIT,” which indicates the cooking
controller is functioning properly. If burner does
not light, a buzzer will sound. Reset controller by
turning power switch OFF for 5 minutes and then
back ON.
The controller will then display “PREHEAT”
“XXX°F.” This message indicates that the Preheat
mode has started. The current oven temperature
is also displayed (which, if the oven has been idle
for some time, will be room temperature).
In the Preheat mode, the burner will fire at high
heat, the convection fans will be on, the rotor will
turn, and the oven light will be off. If unit has a
fireplace, the fireplace will be off.
As the oven burner continues firing, the
temperature readout on the control panel will
steadily rise.
4. Ready Mode
When the oven has reached the programmed
Preheat temperature, the alarm tone will sound for
5 seconds and then go off. The display will show
“READY” and approximately “300°F” (or another
temperature if programmed differently).
Rotisserie Oven 4
The oven is now ready to be loaded. Refer to the
loading instructions on the next page for loading
details.
Page 7
Operator’s Manual
Spit Selection and Preparation
Select the proper spit for the food you will be
cooking. There are a few spits available
from Cleveland Range for this. Some meats,
like chicken, need to be trussed with string
before spitting. Others, like turkey breasts,
ham, and ribs should be secured in the nonskewerable product basket spits. Prepare
enough spits at one time for your entire daily
requirements. Be sure to follow safe food
handling and storage practices. Spit
handling tools, counter top skewer holder,
and a transport cart are available to
make your preparation and handling
easier.
Standby Mode (Idle)
If you don’t load the oven and start a cooking
program within 20 minutes after READY mode
begins, the controller will put the oven into the
Standby mode. The oven displays “STANDBY”
and the temperature is set back to 200°F (or
another temperature if programmed differently).
The oven will remain in standby until you either
turn the oven off or press any button except for the
Prog buttons. Once a button is pressed, the oven
will go into PREHEAT mode and then READY
mode after it reaches 300°F.
Oven Loading Procedure
NOTE: Make sure all food, spits, and spit-loading
implements are ready, so you can work
quickly. If you leave the oven open too long,
the oven may cool off too much, causing the
product to be under-cooked.
1. When the oven is preheated, and the controller
display reads “Ready,” using disposable
gloves, bring the scheduled load over to the
oven. Check to make sure all product is
evenly spaced and secure on the spits.
2. Open the door leaving ample space to access
the interior of the oven. On fireplace door units,
flip up the burner cover so that foreign matter
doesn’t enter and clog the burner ports. Place
the rod end of the spit into the round hole
located in the left drum up to the ¾-inch
washer on the spit.
Before loading the oven….
1. Be sure the oven is PREHEATED.
2. Have all spits loaded with product and secured.
3. Line up the hex side of the spit with the hex
drive socket located in the right side drum.
When sliding the hex into the socket, a slight
rotating motion may be necessary for the hex
to slide into the hole. Once it slides in all the
way, the left side of the spit rod will rest on the
smaller diameter rod.
Note: Always balance the oven load around
the rotisserie wheels. When loading 4 spits or
baskets, skip a position in between each spit.
When unloading, remove every other one.
4. Press the Rotisserie Advance (Jog) Button to
rotate the rotor until the next slots to load are
centered in the opening.
5. When done, flip down the burner cover on
fireplace door units. Close the door firmly and
wipe the oven handle, jog button, and burner
cover with a sanitized towel.
5 Cleveland Range, Inc.
Page 8
Cooking Procedure
Operator’s Manual
Press keys on the control panel with
fingertips only. Never use sharp objects.
Start the Cooking Program
Press the Menu Item key on the control panel that
corresponds to the type and amount of food you are
cooking. This will begin the countdown from the total
cooking time. Notice the red light for the active
cooking program will flash continuously. On fireplace
units, if you want the fireplace ON, push the fireplace
switch to Auto. If you want the interior light ON, push
the light switch to Auto.
During the Cooking Program
1. When the cook program starts, the oven
automatically calculates and displays the total
cook time (of all stages). It then counts down to
show the total time remaining in the cooking
program.
2. You can open the door at any time during
cooking. When the door is opened, the burner,
the convection fans, the rotor, the lights, timing,
and fireplace (if equipped) will stop automatically.
This allows you to check the product temperature
or to correct a problem.
3. TO CANCEL a cooking program, push the menu
item key that is flashing and hold it for 5 seconds.
This will cancel the program.
At the End of the Cooking Program
The controller will count the cooking time down to
“zero”. It will then sound the Audible Tone for 5
seconds and show the message “DONE” on the
display.
If within 5 seconds, you don’t open the door to begin
unloading, the controller will automatically enter the
HOLD mode.
To silence the Audible Tone, you can open the
door, or you can press the Menu Item button that is
flashing.
Adding Additional Cook Time
1. Add Cooking Time – You may check the internal
temperature of the product using a meat
thermometer. If the product has not reached the
desired temperature, add 5 or 10 minutes more
cooking time by pressing key 14 or 15.
2. After Added Cooking is Complete – The Audible
Tone will sound and the controller will
automatically start the HOLD Mode.
In Case of Power Failure
1. If power is restored within 5 minutes, the
controller will continue the cooking cycle where it
left off.
2. If power is off longer than 5 minutes, the
controller will return to Preheat/Ready Mode
when power is restored. Follow your established
restaurant procedures to either restart cooking or
discard product depending on the length of the
power outage.
Co-Cook Procedure
Co-Cook is a secondary cooking-time that can be
programmed for buttons 1 through 13 (see System
Level Programming). Any or all of these keys can
be programmed to any desired time duration, for
example 45 minutes for one key and 1 hour and 10
minutes for another.
To use co-cook, once you have started your
primary cook cycle, you can press a second button
to start a second timing cycle for cooking a second
product that has been loaded into the oven.
Only the time can be programmed for co-cook. All
other parameters – temperature, speed, fan, etc. –
are controlled according to the primary cook
program parameters.
The rotisserie oven’s Co-Cook feature allows you to
cook two different products in the oven at the same
time.
You can load both products at the same time, or load
the second item later. The one restriction is that the
co-cook time for the second item must be shorter
than the total cook time remaining for the first item.
To use Co-Cook, press the first menu item key to
start the first time clock. The display will show the
total time remaining for the first item. Then,
whenever the second item has been loaded, press
the second menu item key that corresponds to the
amount of time you want. The light of the co-cook
menu item will flash at a faster rate than the primary
item.
After pressing the second menu item key, the display
will show the total cook time for the second item, and
will begin counting down. (The clock for the first item
continues counting down, but this occurs in the
background and is not visible in the display.)
To cancel co-cook, press the menu item button for 2
to 3 seconds, until the light turns off.
When the co-cook time reaches zero, the Audible
Tone sounds. The clock resets itself and shows the
cook time remaining for the primary menu item. The
first item will now complete its cooking cycle. You
must unload the second item right away to keep it
from overcooking.
Rotisserie Oven 6
Page 9
Operator’s Manual
Holding Procedure
Once the product in the oven has finished cooking,
the controller will sound the Audible Tone, and
enter the hold mode.
1. HOLD will maintain the oven temperature at
175 °F (or other programmed temperature).
The rotor will turn at 1 rpm, the vent will be
closed, the lights on, and the fireplace on (if
equipped).
2. The display will count up the time spent in
HOLD, which is 2 hours maximum. During
HOLD, you may remove spits as needed for
serving. (see unloading procedure)
3. After 2 hours in HOLD, the Audible Tone will
again sound. This is the time limit the product
may safely be held without serving. At this
time, remove any remaining product and
discard.
4. If you want to load another batch of product
after HOLD has ended, press any menu item
key. This will cause the controller to start a
new Preheat/Ready cycle. Wait for the
Audible tone and the “READY” message
before reloading the oven.
5. If you don’t want to start another load after
emptying the oven, just close the door and
allow it to automatically go into the STANDBY
mode. Then, when you are ready for another
load, press any key, except the Prog keys, to
start the Preheat/Ready cycle
6. If you are done cooking for the day, turn the
POWER switch to OFF, wait at least 15
minutes for the oven to cool down, and
perform the Daily Cleaning/Maintenance
Procedure.
Unloading Procedure (with optional recommended spit handling tools)
WARNING:
Oven interior and spits are extremely hot. Use
caution when unloading to avoid being burned.
1. Open the door leaving ample space to access
the interior of the oven. On fireplace door
units, flip up the burner cover so that foreign
matter doesn’t enter and clog the burner ports.
2. Take 2 sanitized spit handling tools.
3. Use the Rotisserie Advance (Jog) button to
bring the desired spit around to the unloading
position.
4. With a spit handling tool in your right hand,
hook the hex lug on the inside of the ¾”
washer.
5. With the other spit handling tool in your left
hand, hook into the rod end of the spit to the
inside of the ¾” washer.
6 Lift up the rod end with the left hand and slide
the spit to the left. This releases the hex from
the right drum.
7. Pull out with your right hand and slide spit to
the right, releasing the rod from the left drum.
8. Place the spit on a cutting table, into a holding
cabinet, or into the warming cabinet below the
rotisserie (if equipped).
9. Repeat steps 3-8 for the remaining spits.
SPIT HANDLING TOOL
7 Cleveland Range, Inc.
Page 10
How to Ensure Uniform Cooking Characteristics
Operator’s Manual
You must follow consistent preparation steps to
ensure that foods are always uniformly cooked.
Here are some guidelines for keeping your food at
a consistent quality:
1. Always PREHEAT the oven before loading the
food product.
2. Have all spits prepared with food product prior
to loading oven. Don’t load food onto spits and
into the oven at the same time.
3. Have all spits at the same (chilled)
temperature prior to loading.
4. Load the oven quickly. Don’t leave the oven
door open longer than necessary to load
product; excessive cool-down of the oven can
cause food to be undercooked after cooking
cycle is completed.
5. Use the 5-minute continue-cook button to
compensate for a cooled-down oven. The first
load of the day may need an extra 5-minute
cook time.
6. When a cooking program is complete, always
check the product’s internal temperature with a
meat thermometer. If it’s too low, add 5 or 10
minutes more cooking time by pressing key 14
or 15, after canceling the primary cook
program.
7. When smaller amounts of food product are
cooked, monitor and replenish the drip pan
water as needed. The water helps the oven
maintain a more uniform temperature and
moisture level.
Problem Messages / Alarm Tone
If you see an error message, write it down
and refer to the “ERROR MESSAGES”
section later in this guide.
After you turn on the oven, and during subsequent
operation, if the controller detects any problems, it
will show an error message. For most problems an
alarm tone will sound.
Some problems you will be able to correct and
continue operation. Other problems may require
the assistance of an Authorized Service
representative.
Follow procedures in the Error Messages section
to acknowledge the alarm and turn it off.
Do not attempt complicated repairs by yourself –
call an authorized service person.
NOTE: If the controller detects a problem that goes
away after a short period of time, the message will
disappear, but the alarm will continue until you
press the appropriate button to cancel it.
Rotisserie Oven 8
Page 11
Operator’s Manual
Operator’s Daily Cleaning/Maintenance
The oven must be cleaned daily to maintain good
performance and appearance.
You will need the following items:
• A bucket of soapy water (non-chlorinated
soap)
• A spray bottle of floor and wall cleaner
• A spray bottle of food-safe sanitizer
• A spray bottle of Jef-Guard (or other food-
safe coating spray)
• A scrub pad
• A clean cloth
• A squeegee
• Safety goggles
• Oven cleaning gloves
• Razor blade scraper (for fireplace models
only)
1. After the last cooking cycle of the day, turn the
POWER switch OFF and allow at least 15
minutes for the oven to cool.
2. Drain the drip pan. Place an empty 5-gallon
bucket under the drain and open the drain
valve.
10. Clean all parts of the rotisserie wheels using
spray cleaner. Pull the clevis pins and slide
the drums to the center. Clean the oven walls
behind the wheels and the backsides of the
wheels.
11. Wipe out any grease from the bottom of the
oven.
12. With a dry towel, wipe down all surfaces of the
oven
13. Spray rotisserie wheels with the sanitizer and
allow to air dry. Lift the burner protector shield,
in single-door models, it is the hinged plate
that hangs down at upper-rear of the oven.
(Two-door models are supplied with a loose
shield for this same purpose.) Taking care not
to spray the burner, the ignitor or the
temperature probe, spray the entire interior of
the oven with an oven sanitizer. Allow to airdry.
14. Again covering the burner, spray and wipe the
upper surfaces of the oven with Jef-Guard or
equivalent, taking the same precautions as
above.
3. Remove the grate(s) covering the drip pan.
4. Squeegee up the grease in the pan and
remove.
5. Remove, by pulling toward you, the “jet plate”
covering the fans in the top of the oven, and
take it and the grate to a dishwashing area.
6. Remove the two convection fan blades and
clean them with spray cleaner and a scrub pad.
7. Spray the inside oven window(s) with floor and
wall cleaner and allow to sit for 5 minutes.
Wipe clean and repeat if necessary; never use
scouring pads or oven cleaner.
8. Clean the fireplace
glass, if applicable, with
non-chlorinated soap
and water; use razor
blade scraper if
necessary.
9. Wipe down the inside
walls of the oven with
the soapy water. Never
use a hose or water
jet.
hang front of Jet Plate
into these corners
hang rear of Jet Plate
15. Replace the grate(s) and spray all inside
surfaces (including backside of drums) with the
food-safe oven coating, taking care not to
spray the burner, the ignitor or the temperature
probe.
16. Spray both sides of the jet plate and both fan
blades with the food-safe coating and reinstall.
Note that the fan blades must be installed to
their original motors; they are not
interchangeable.
17. Preheat the oven for 5 minutes to seal the
food-safe coating, and shut off the oven.
18. Examine vent hood and fireplace flue (if
equipped) for signs
of sooting or
blockage. Call
service if problems
are suspected.
Jet Plate
9 Cleveland Range, Inc.
Page 12
Programming,
Troubleshooting
& Technical
Information
Control Panel…………………………………….. 11
Programmer’s Worksheet……………………… 13
Programming Tips & Techniques……………. 14
Menu Item Programming………………………. 15
Co-Cook Programming……………………...… 17
System Programming………………………….. 18
Troubleshooting………………………………… 19
Error Messages…………………………………. 20
Operator’s Manual
Rotisserie Oven 10
Page 13
Operator’s Manual
Rotisserie Control Panel
Control Panel –
This is the interface
between the control system and the
operator. It consists of indicator
lights, a 2-line alphanumeric display,
and 21 control buttons (keys).
Status Indicators –
These lights
show the state of four of the
controller’s outputs. When the
light is on, the associated output is
active.
UP and RIGHT Arrow Keys –
These are used during
programming to cycle through the
available parameters.
TEMP Key –
During any cook
program, press this key to see the
oven temperature. (During cook,
the readout usually shows the
current stage and the total time
remaining.)
PROG Key –
Use this key to start
any programming operation (for
example, entering cooking
programs and setting system-level
parameters.) You will need to
know passcodes to access the
programming function.
Menu Item Keys –
These 16 keys
are used primarily to start cooking
programs. Use them also to
cancel cooking programs. (Some
keys, including 13, 14, 15, and 16,
have special functions, described
opposite.)
Menu Item Light –
This light
flashes during a cooking program
to indicate which program is
active. It also flashes during
programming to indicate which
item is being programmed. During
a Co-Cook operation a second
light flashes more rapidly to
indicate that a second timing cycle
is running.
The rotisserie oven is operated by a
computerized control system. The
system controls the time, temperature
circulating fans, vent, rotor speed, and
oven lamp.
LOW HIGHVENT
TEMP
PROG
FAN
PROG
REVIEW
Alphanumeric Display –
The display
provides many functions during oven
operation. It displays the
of the oven, whether Preheat,
status
current
Ready, cooking State, Hold or
Standby. It also displays current
temperature
and
(either time
time
remaining during cooking, or time
accumulating during Hold). During
programming, the display shows
current settings
choices. It also displays
messages
and available
error
in case there is a problem
with the unit.
Audible Alarm
– In conjunction with
the Control Panel’s visual indicators,
an alarm tone is sounded to
the operator’s attention
attract
during
normal operation. The alarm will
sound for 5 seconds when the oven
has changed status – for example,
when the oven is “Ready” or a cook
program is finished. The alarm will
also sound for 5 seconds when the
door is opened during cook. However,
the alarm will sound and remain on for
error conditions.
When this
happens, observe the display and
refer to the
Error Message
section in
the back of this guide. To turn off the
alarm for most error conditions, just
press any button to confirm that the
alarm has been received.
Special Function Keys –
Keys 13,
14, 15, and 16, normally Menu Item
keys, have dual functions.
Key 13 – Auto Hold:
To cancel
current cooking cycle, press and hold
this button for at least 1 second, and
the oven will go into the Hold mode.
Key 14 – Add 5:
After any cook
program goes into Hold, press this key
to add 5 minutes of cook time, (uses
the parameters of the cook program’s
last stage).
Key 15 – Add 10:
Same as key 14,
but adds 10 minutes.
Key 16 – Fireplace
: If unit has a
fireplace, this button will run the
fireplace only for 8 hours.
Co-Cook Function
– All keys except 14, 15 and 16 can be programmed (at System Level) to provide a second cook
cycle while the first runs in the background. (Thus you can load and cook a second product while the first continues to
cook – but there must be enough time left in the first one or you can’t start the second.) All first item cook parameters
remain in effect in Co-Cook. The Co-Cook item light flashes at 3-times normal speed. The readout shows time
remaining in Co-cook until it ends. Then the alarm sounds, the light stops flashing, and the first item’s time remaining
is displayed. (To cancel a C-Cook program press and hold the button for 3 seconds.)
11 Cleveland Range, Inc.
Page 14
How the Rotisserie Oven Controller Operates
Operator’s Manual
300
200
PREHEAT
PREHEAT brings
oven temperature
to near-cooking
level (typically
300° F)
in 20 minutes,
oven goes into
If cooking
is not started
STANDBY
COOK STAGES
The number of stages,
hours, and temperatures
depends on how the
menu item key has been
programmed
Menu Item key press
begins cooking program
HOLD
After COOK ends,
heat is reduced –
HOLD stage keeps
product warm;
typically 2 hours at
175° F
or
300
200
100
Standby
In STANDBY or HOLD, press a
menu item key to re-start
Powering-up
the oven starts the
PREHEAT process
F
Preheat / Ready
Stage 1
Cooking Program
Stage 2
Stage 3
STANDBY
READY
READY holds oven
temperature at or
near cooking
setpoint, ready for
loading food. But,
if no menu item
key is pressed
after 20 minutes,
Standby is started
(from Ready)
After oven goes
into Ready, if no
menu item key is
pressed within 20
minutes, then
oven goes into
STANDBY (200°
F) until a new key
is pressed
PREHEAT/READY
Hold
20 min.
Standby
or Preheat
STANDBY
(from Hold)
If menu item key is not
pressed within 20
minutes after Hold
ends, oven goes into
STANDBY – if menu
item is later pressed,
Preheat/Ready starts
Standby
100
Rotisserie Oven 12
Page 15
Operator’s Manual
Programmer’s Worksheet
Menu Item No.
______________
name of menu item
STAGE - 1
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
STAGE - 2
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
Menu Item No.
______________
name of menu item
STAGE - 1
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
STAGE - 2
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
Menu Item No.
______________
name of menu item
STAGE - 1
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
STAGE - 2
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
Menu Item No.
______________
name of menu item
STAGE - 1
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
STAGE - 2
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
STAGE - 3
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
HOLD
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
open / closed
___________ Fan
on/pulsed
STAGE - 3
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
HOLD
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
open / closed
___________ Fan
on/pulsed
STAGE - 3
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
HOLD
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
open / closed
___________ Fan
on/pulsed
STAGE - 3
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
regulate / closed
_____ RPM Speed
1, 2, or 3
___________ Timer
standard / flex
___________ Heat
high / low
HOLD
_ _ : _ _ : _ _ Hours
h h : m m : s s
_ _ _° Temp
___________ Vent
open / closed
___________ Fan
on/pulsed
13 Cleveland Range, Inc.
Page 16
Programming Tips and Techniques
g
TYPE OF FOOD – Meats with large
bulk take longer to cook than meats
with less bulk (roasting chickens
versus spare ribs, for example).
NUMBER OF SPITS – An important
factor in setting up a cooking program.
A fully loaded oven (all spits fully
loaded) takes longer to cook than a
lightly loaded one with the same type
food. Separate keys must be
programmed for small and large loads.
Chicken
5/6 Spits
name of menu item
0 0
: 4 5 : 0 0 Hours
h h : m m : s s
3 0 5° Temp
STAGE - 1
3
Operator’s Manual
The example on this page shows a
typical program. Only minor alterations
in time and temperature are needed to
cover most cookin
HOURS – Determines the length of time per
stage.
Note: Typical TOTAL cooking time for most
meats cooked in the rotisserie oven ranges
between 1 and 1-1/2 hours.
requirements.
Stage 1 is usually programmed at a
higher temperature and rotor speed
than stage 2. This brings the
product up to cooking temperature
faster and helps seal in juices.
TIMER – The STANDARD mode runs
the clock at normal rate. FLEX is a
special clock mode that can
compensate for extra heat
requirements by adding cooking time.
STANDARD is the default setting.
Note that during cooking, the “time
readout” on the controller panel is
the TOTAL TIME REMAINING
before the complete program is
finished, not the time remaining in
any specific stage.
STAGES – Up to 3 stages can be
programmed – 1 stage must be
programmed and 2 are the most
common.
Note that if any stage is not
programmed (that is, the hours
show 00:00:00) then it is skipped by
the oven controller.
The values shown in Stage 3 at right
are the default values assigned by
the controller when any stage is not
programmed.
HOLD – The HOLD values shown at
the right are the recommended settings
to keep the prepared food at optimum
conditions for serving. (These are the
default values and do not need to be
altered during programming, unless
desired.)
REGULATE Vent
regulate / closed
3 RPM Speed
1, 2, or 3
STANDARD Timer
standard / flex
HIGH Heat
high / low
STAGE - 2
0 0
: 4 5 : 0 0 Hours
h h : m m : s s
2 9 0° Temp
REGULATE Vent
regulate / closed
2 RPM Speed
1, 2, or 3
STANDARD Timer
standard / flex
LOW Heat
high / low
STAGE - 3
0 0
: 0 0 : 0 0 Hours
h h : m m : s s
_ 3 2° Temp
REGULATE Vent
regulate / closed
0 RPM Speed
1, 2, or 3
STANDARD Timer
standard / flex
LOW Heat
high / low
HOLD
0 2
: 0 0 : 0 0 Hours
h h : m m : s s
1 7 5° Temp
CLOSED Vent
open / closed
PULSED Fan
on/pulsed
SPEED (OF ROTISSERIE ROTOR) – Three
rotor speeds are available, 1, 2 or 3 rpm. The
speed mainly affects the level of browning and
surface drying.
TEMP – Range is 140 to 400 deg. F. (or 22 to
204 deg. C.) System-level programming can be
used to select F or C.
VENT – The vent is at the top of the oven. In
the normal mode of operation it is set to
“regulate.” This means the burner is on
continuously and oven temp is regulated by
opening and closing the vent. This technique
helps control moisture.
HIGH HEAT vs. LOW HEAT - This
programming factor determines the heat input
to the gas burner (60,000 BTUH versus 48,000
BTUH).
Note that the HIGH or LOW HEAT parameter
describes the intensity of the heat, not the
temperature of the oven.
High heat intensity increases browning and
helps seal in juices.
VENT AND FAN DURING HOLD – the vent is
CLOSED and the circulation fans PULSED
during Hold. This technique keeps the product
from losing too much moisture. In Hold, oven
temperature is regulated by turning the gas
burner on and off.
Rotisserie Oven 14
Page 17
Operator’s Manual
t
t
t
r
t
t
t
t
t
Y
t
t
t
t
t
t
t
t
t
t
t
t
t
M enu Item Program m ing - Rotisse rie Controlle
1. Access M enu Item Prog ramming (Pa ssw o rd 5-1-5-10)
PROG
(In any
mode
except
cook)
Password
____
Only persons
who know the
password can
set or change
cooking
parameters
Password
****
When you press the
password keys, the
2nd line of the display
shows star characters.
After the 4th key,
it checks the code.
If the password is correct,
he "Program Item" / "Version"
message is shown.
If the password is incorrect
he controller returns to
he mode it was in.
2. Select M enu Item Key to Program
Press
any
Menu
Item
key
The Menu Item's
indicator light
begins flashing
o show it is in
he program mode
NOTE:If during programming you don't
press any button for 5 minutes,
he controller will automatically
exit the programming mode
and return to its previous state
3. St ep Th rough and Program Desired Param eters
How to Program the Param eters?
Every time you press the Menu Item key, the next parameter is displayed.
ou can stop at any parameter and make changes. Moving on to the next
parameter causes the value in the current parameter to be stored
First, use the Programmer's Worksheet in this guide to prepare
a program's desired values and settings. Then, follow
he instructions on the next page to program the parameters.
Program
Item
Version
CR xx.xx
The "Program Item" / "Version Number"
message indicates that a
Menu Item key should be
pressed to begin programming.
age 1
S
hh:mm:ss
S
age 2
h:mm:ss
h
age
S
h:mm:ss
h
Hold
h:mm:ss
h
3
age 1
S
___
S
age 2
___
Stage
___
Hold
___
age 1
S
F
F
3
F
F
_
(vent)
S
S
age 2
age 2
_
(vent)__(vent)
Stage
_
(vent)
Hold
_
(vent)
4. Ex it Programming Mode
PROG
Press the
PROG key.
The controller
will return to
its previous
operation
_
S
S
_
S
3
S
_
S
Hold
_
Fan
peed
age 2
p
eed
age
p
eed
_____
_
_
3
_
age 1
S
age 1
S
____
Heat
S
age 2
____
Heat
3
Stage
____
Heat
Pressing the Menu Item
key after the last Hold
parameter causes the
display to return to Stage 1
NOTE:
The controller is pre-programmed
at the factory with default settings.
Some Menu Items have typical
cooking programs, and some have
no time programmed, making them
"Unused."A system Level password
can be used to revert all settings
o default.
15 Cleveland Range, Inc.
Page 18
Menu Item Programming Instructions
How to Set the Time / Temperature Parameters
(follow the numbered steps below)
Operator’s Manual
After selecting PROG and
1
entering the password,
press the
MENU ITEM
you want to program. The
first two parameters will be
the stage's time and temp.
When you access
2
a time or temperature
setting, the current value
will display, with the
first digit flashing.
To activate any other
3
digit to program, press
RIGHT-ARROW
until the digit you
want begins flashing.
(
for example
)
4
5
Press the UP-ARROW
button to scroll
through values -stop at the
desired
value
Advance until the digit
you want to change is flashing
How to Set All Other Parameters
(follow the numbered steps below)
6
Keep pressing
RIGHT-ARROW
button to advance
to other digits in
the time (or temp)
parameter you want
to program
7
3
After setting the Stage 1 time and temperature,
1
as described above, pressing the MENU ITEM
button again and again will bring up the
Vent setting, followed by Speed, Timer,
and Heat.
As you display each of these
2
oven parameters, the current
setting will be flashing.
(In the example at right, the VENT
parameter is shown, which can be
either "regulate" or "closed.")
CHOICES
VENT
SPEED
TIMER
HEAT
"regulate"
"1" "2" "3"
"standard"
"highheat"
"closed"
"flex"
"low heat"
When finished programming a parameter, press
the MENU ITEM button
to move to next parameter
-- use the UP ARROW
button to select the
desired setting.
After setting the "HEAT" parameter for Stage 1, pressing the
5
MENU ITEM button again and again brings up Stages 2 and 3.
(After the 3 cooking stages comes the "HOLD" parameters,
which generally shouldn't be changed - see text in the manual.)
4
Rotisserie Oven 16
Page 19
Operator’s Manual
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
Co-Cook Programming and Program
1. Access Co-Cook Programming (Password 2-10-
PROG
(In any
mode
except
cook)
Password
____
Only persons
who know the
password can
set or change
cooking
parameters
Password
****
When you press the
password keys, the
2nd line of the display
shows star characters.
After the 4th key, the
controller checks
he password.
2. Select Co-Cook Key to
Press any
Menu Item
key except
14, 15, 16
The Menu Item's
indicator light
begins flashing
o show it is in
he program mode
NOTE: If during programming you don't
press any button for 5 minutes,
he controller will automatically
exit the programming mode
and return to its previous state
3. Enter the Co-Cook Time
The only parameter that can be programmed for Co-Cook
is the time. Factory default for keys 1 - 13 is 0 (zero)
minutes.
minutes.
Program
Item
Version
If the password is correct,
he "Program Item" / "Version"
message is shown.
If the password is incorrect
he controller returns to
he mode it was in.
CRxx.xx
The "Program Item" / "Version Number"
message indicates that a
Menu Item key should be
pressed to begin programming.
How to Program the Parameter?
Follow the instructions on the previous page regarding
he programming of time parameters.
4. Exit Programming
PROG
Press the
PROG key.
The controller
will return to
its previous
operatiom
Access Program Review
PROG
REVIEW
Can be
pressed
at any
ime
If a stage has zero time programmed, that
stage will be skipped and the next will be
shown; if all stages have zero time, the
display will show "UNUSED ITEM." To view
another item at any time, press its button.
Select
Item
Prompt for
Menu Item;
no password
needed
Press the Menu
Item button;
keep pressing
o view all
settings
Stage 1
h:mm:ss
h
age 2
S
h:mm:ss
h
Stage
h:mm:ss
h
Hold
h:mm:ss
h
age 1
S
___
F
S
age 2
___
F
3
Stage
___
F
Hold
___
F
S
age 1
_
(vent)
S
age 2Stage 2
_
_
(vent)
(vent)
3
S
age
_
(vent)
Hold
_
(vent)
S
_
_
_
3
_
_
age 1
p
eed
S
S
age 2
p
eed
S
Stage
p
eed
S
Hold
Fan
_____
Stage 1
_
____
Heat
Stage 2
_
____
Heat
S
age
____
3
Heat
3
_
17 Cleveland Range, Inc.
Page 20
Operator’s Manual
t
t
t
t
t
t
t
t
t
t
t
t
System Le ve l Program m ing - Rotisse rie Controller
Begin
program-
Enter this password . . .
ming
PROG
Select the controller's
display units, either
Fahrenheit or Celsius
PROG
Offset (calibrate)
he temperature probe;
(as compared against
precision thermometer)
PROG
Ready temperature
up or down from factory
default of 300F (149C)
Password
____
Password
____
Password
____
Shift
. . . to program
his parameter
mp
e
T
splay
i
D
mp
e
T
ffset
O
Ready
emp
T
Press
any key
o con-
inue
"Any
"Any
Key"
Key"
except
(
PROG
"Any
"Any
Key"
Key"
except
(
PROG
"Any
"Any
Key"
Key"
except
(
PROG
)
)
)
Display
while
program-
ming
T Disply
F (or C)
Offset
T
___
F (or C)
Rdy Temp
+/- ___F/C
Programming
Instructions
Use UP Arrow key
o toggle
between F and C
Use RIGHT Arrow key
o select which digit
o change
(digit will flash)
Use UP Arrow key
change value of digit
Note: Range of offset
is +/-40 F (+/- 22 C)
Use RIGHT Arrow key
o select which digit
o change
(digit will flash)
Use UP Arrow key
change value of digit
To
Exit,
press
PROG
PROG
PROG
PROG
Standby temperature
default of 200F (93C)
PROG
controller parameters
Password
____
Change
from the factory
Password
____
Reload factory
defaults for all
Standby
mp
e
T
Key"
Key"
except
(
PROG
Key"
Key"
except
(
PROG
"Any
"Any
"Any
"Any
bTemp
S
___
F/C
)
)
Use RIGHT Arrow key
o select which digit
o change
(digit will flash)
Use UP Arrow key
change value of digit
PROG
PROG
Rotisserie Oven 18
Page 21
Operator’s Manual
y)
Troubleshooting
(if these procedures do not find the problem,
call an authorized service agenc
Unit does not come on; there are
no lights on the panel.
Unit comes on, but no burner and
no rotisserie drive.
Display reads “READY” or
“SETBACK” or “HOLD”
The oven light will not work. 1. Make sure the power switch is on.
The fireplace burner will not light.
(Fireplace models only.)
The spits or baskets won’t fit in
the oven.
The spits (“V” or basket) fall out. 1. Make sure the spit or basket is installed properly. The spit spear end passes
1. Make sure power cord is plugged in.
2. Check circuit breaker for the outlet.
1. Make sure door is closed all the way; safety circuit prevents flame and rotation
with door open.
1. There is no problem; these are normal messages. Refer to operating procedures.
2. Make sure a menu item program is active. Oven light will only come on when a
program is active.
3. If fireplace model, make sure light switch is on (auto).
1. Make sure the power switch is on.
2. Make sure a menu item program is active. Fireplace will only come on when a
program is active.
3. Make sure fireplace switch is on (auto). Call service if problem persists.
1. Make sure both left and right rotisserie drum hubs are located in their proper
positions and are seated in the drive shaft roll pins. Look for bent hex drive or
debris in the hex socket.
through the hole in the left rotisserie drum and then the right side of the spit is
engaged into the drive socket in the right rotisserie drum. The spear end of the
spit must then rest in the hole in the left drum. Make sure only the small diameter
portion of the spear end is in the left drum.
The rotisserie burner ignites, but
no rotor rotation.
Rotor seems jerky, not smooth. 1. Make sure both rotisserie drum hubs are located in their proper positions and are
Rotor moves at different speeds
at different times.
The product does not cook
evenly.
The product is not done, or oven
does not come up to
temperature.
The product is overdone, or oven
temperature exceeds the set
point.
The wrong program button was
pushed.
1. Check the rotisserie drive motor circuit breaker. If the button is extended, reset it
by pushing it in. If not, call for service.
locked by quick release pins.
1. There is no problem with the machine. The rotisserie motor has 3 different
speeds that can be programmed in different cooking cycles.
1. Make sure the air baffle or “jet plate” is in place at the top of the oven. Check to
see if both convection fan blades are securely mounted in their proper place and
that they are both spinning when in operation.
1. Make sure the proper menu item for the product being cooked was initiated and
that the menu item’s programming is correct.
2. Check to see that the temperature controlled vent in the top of the oven is not
stuck in the open position.
3. The oven must be preheated before product is loaded.
4. The product must be loaded as quickly as possible so that the oven does not cool
down too much.
1. Make sure the proper menu item for the product being cooked was initiated and
that the menu item’s programming is correct.
2. Check to see that the thermostat controlled vent in the top of the oven is not stuck
shut.
3. Make sure that 3 gallons of water in the bottom of the oven have not evaporated.
1. To cancel a program, hold down the button of the cooking program for 5 seconds.
When the item light goes off, you can select another program
Burner lights, but turns off in a
few seconds or burner fails to
light. Buzzer sounds.
1. Check the “jet plate” position.
2. Reset the controller by turning the POWER switch to the OFF position for 5
minutes then back to ON. Call service if problem persists.
19 Cleveland Range, Inc.
Page 22
Error Messages
p
Display Cause Remedy
Shorted
Probe
Or
Faulty
Heater
This three-part message (plus alarm) is
displayed when the controller detects that
the oven temperature probe is shorted, or
that the oven temperature is not rising, or is
rising too slowly.
Turn off the alarm by pressing any button
on the control panel.
Open the door to check if there is any heat
at all. If there’s no heat, either the probe is
open and the burners are kept off by the
controller, or the gas supply is turned off,
which you should check. If there is some
heat check that the gas valve is fully open.
If the gas is OK, then the problem will
require service.
Operator’s Manual
Over
Current
Power
Loss
Probe
O
en
Checksum
Error
The controller has detected an overcurrent
condition in the rotisserie drive motor. The
alarm tone will sound continuously.
A power loss of more than 5 minutes will
sound the alarm tone and display this
message. Press any button to cancel the
alarm.
This message is displayed (with alarm) if
the oven temperature probe fails open. If
the open condition goes away before 20
seconds, the oven will return to its previous
state; however, the alarm must be turned off
by pressing the TEMP button
This message is displayed upon power up if
the controller detects a fault within one of
the Menu Item programs, or if new controller
software has been installed. Press any
button to acknowledge the message.
The only way to turn off the alarm is to turn
power off to the oven and turn it back on.
Check for some obstruction of the drive
system. Call service if the error does not
go away.
A power loss of 5 minutes or less will not
sound the alarm or show this message.
When power returns, the cooking cycle will
resume where it left off. A longer loss will
cause the oven to reset and enter the
Preheat/Ready mode.
If the probe remains open, call for service.
Unused
Item
System
Init
Version
CR xx.xx
Rotisserie Oven 20
This is not an error message. It is displayed
when you are attempting to review a Menu
Item button which has not been
programmed.
System
Init
New
Version
These are not error messages. They are
displayed upon power up of the oven,
when the software is initializing. The “New
Version” message is shown when new
software is detected for the first time.
Loading...