Cleveland Motion Controls ULTRA SERIES CANTILEVER TRANSDUCER CLTSCM User Manual

MODELS: CLTEC, CLTSC, CLTECM

7550 Hub Parkway Cleveland, Ohio 44125 Phone: [phone] Fax: [phone] www.CMCcontrols.com

INSTRUCTION MANUAL

(MAN-70252)

®

C

LEVELAND-KIDDER

ULTRA CANTILEVER TRANSDUCER

& CLTSCM

REVISION

AA

Industrial Products Division

ULTRA SERIES CANTILEVER TRANSDUCER MAN-70252 REV. AA

REVISION HISTORY

Rev ECO Author Date Description of Change

AA XXX RDL 1/27/2005 As Released

PAGE 2 OF 18

MAN-70252REV. AA ULTRA SERIES CANTILEVER TRANSDUCER

TABLE OF CONTENTS

1 IMPORTANT INFORMATION.........................................................................5

1.1 ORDER NUMBERS ........................................................................................................... 5

1.2 CONTACT INFORMATION AND SERVICE ASSISTANCE ..........................................................6

1.3 RECEIVING AND UNPACKING ............................................................................................ 6

1.4 PRE-INSTALLATION PRECAUTIONS....................................................................................7

1.4.1 Shipping..................................................................................................................7

1.4.2 Roll Balance............................................................................................................ 7

1.4.3 Critical Roll Speed...................................................................................................7

1.4.4 Avoiding Damage to the Transducer....................................................................... 7

1.4.5 Excitation Voltage...................................................................................................7

2 SPECIFICATIONS.......................................................................................8

2.1 FORCE RATINGS .............................................................................................................9

2.2 BEFORE INSTALLING THE TRANSDUCER............................................................................9

2.2.1 Installation Precautions...........................................................................................9

2.2.2 Safety Considerations.............................................................................................9

2.2.3 Mounting Configurations.......................................................................................10

2.2.4 Mounting Hardware and Fastener Torque Recommendations .............................. 11

2.2.5 Mounting Dimensions............................................................................................12

3 INSTALLING THE CANTILEVERED TRANSDUCER.......................................... 13

3.1 MOUNTING THE TRANSDUCER........................................................................................ 13

3.2 MOUNTING THE SENSING ROLL......................................................................................14

3.3 ORIENTING THE CANTILEVER TRANSDUCER.................................................................... 14

3.4 CHECKING THE TRANSDUCER MOUNTING .......................................................................15

3.5 ELECTRICAL CONNECTIONS AND WIRING ........................................................................15

3.6 MATING CONNECTORS ..................................................................................................15

3.7 CALIBRATION ................................................................................................................ 16

4 TROUBLE SHOOTING...............................................................................17

4.1 DC RESISTANCE CHECK................................................................................................18

4.2 DC VOLTAGE AND CURRENT CHECKS ............................................................................ 18

PAGE 3 OF 18

ULTRA SERIES CANTILEVER TRANSDUCER MAN-70252 REV. AA

WARRANTY

Cleveland Motion Controls warrants the goods against defects in design, materials and workmanship for the period
of 12 months from the date of delivery on the terms detailed in the Cleveland Motion Controls, Inc. Terms and
Conditions of Sale, document number AO-90131

Cleveland Motion Controls, Inc. reserves the right to change the content and product specification without notice.

© 2005 in this document is reserved to:
Cleveland Motion Controls, Inc.
7550 Hub Parkway
Cleveland, OH 44125
216-524-8800 Phone
216-642-2199 Fax

INTENDED USERS

This Instruction Manual is to be made available to all persons who are required to configure, install or service the
equipment described in this manual or any other related activity.

ADDITIONAL INFORMATION

ATTENTION: The following information is provided merely as a guide for proper installation. Cleveland Motion
Controls cannot assume responsibility for the compliance (or failure to comply) to any code (national, local or other)
that prescribes the proper installation of this electro-mechanical device or associated equipment. A hazard of
personal injury and/or property damage can exist if applicable codes are not adhered to.

CE EMC RESPONSIBILITY

The Cleveland-Kidder Ultra Transducer may be used by a manufacturer as a component of a larger system, along
with other components, which may or may not bear the CE mark. The system assembler is responsible for the
compliance of the system as a whole with the EMC Directive.

Before installing the Transducer you must clearly understand who is legally responsible for conformance with the
EMC Directive. Misappropriation of the CE mark is a criminal offense.

PAGE 4 OF 18

MAN-70252REV. AA ULTRA SERIES CANTILEVER TRANSDUCER

1 IMPORTANT INFORMATION

1.1 ORDER NUMBERS

Use the following example and Tables A, B and C to determine order numbers for:

• Ultra Series Transducers

• Mounting Ki ts

• Shaft Adapter

Figure 1 – Example for Determining Transducer, Mounting Kit and Shaft Adapter Order Numbers

If you needed to Purchase a Transducer, Mounting Kit and Shaft
Adapter corresponding to following description:

• Size 2 cartridge body.

• Side connection (to allow flange mounting).

• Maximum Working Force (MWF) of 100 lbs.

• Shaft Adapter to accommodate 1 inch (outside diameter)

shaft

Then, you would use Catalog Numbers:

Ultra Series Transducer = MO-13458-00 (Refer to Table A)
Mounting Kit = MO-04498 (Refer to
Shaft Adapter = MO-12145-1 (Refer to

Table B)

Table C)

Having the following information at hand will help you to easily determine which of the Ultra Series Cantilevered
Transducers is right for your application:

• The desired diameter of the shaft bore

• The type of electrical connection

• Maximum wor k in g for c e

Use Table A to determine the catalog number for the proper Cantilevered Transducer.

Table A – Determining a Catalog Number for the Ultra Cantilevered Transducer

English

Cartridge Size

1T ALUM MO-13453 MO-13454 0.1 lb. 1 lb. 5 lb. 10 lb.
1T STEEL MO-13455 MO-13456 25 lb. 50 lb. 100 lb.
2T STEEL MO-13457 MO-13458 100 lb. 250 lb. 500 lb.

Metric

Cartridge Size

1T ALUM MO-13459 MO-13460 0.5 N 5 N 20 N 45 N
1T STEEL MO-13461 MO-13462 100 N 200 N 450 N
2T STEEL MO-13463 MO-13464 450 N 1000 N 2000 N

End

Connector

(CLTEC)

End

Connection

(CLTECM)

Side

Connector

(CLTSC)

Side

Connection

(CLTSCM)

Order Code Suffix, M.W.F.

-00 -10 -20 -30

Order Code Suffix , Metric M.W.F

-00 -10 -20 -30

PAGE 5 OF 18

ULTRA SERIES CANTILEVER TRANSDUCER MAN-70252 REV. AA

Table B – Determining a Mounting Kit Catalog Number for the Ultra Series Cantilevered Transducer

Mounting Style

Bearing (BR)
Flange (FL)
Pillow Block (PB)

Table C – Determining a Shaft Adapter Catalog Number for the Ultra Series Cantilevered Transducer

If Finished Bore Diameter
(nominal I.D) equals:

1/2 inch MO-12143-0 MO-12144-0

5/8 inch MO-12143-1 MO-12144-1
3/4 inch MO-12143-2 MO-12144-2 MO-12145-0
1 inch MO-12143-3 MO-12144-3 MO-12145-1
1-1/8 inches MO-12143-4 MO-12144-4 MO-12145-2
1-1/4 inches MO-12143-5 MO-12144-5 MO-12145-3
1-1/2 inches MO-12145-4

17 millimeter MO-12146-0 MO-12147-0
20 millimeter MO-12146-1 MO-12147-1 MO-12148-0
25 millimeter MO-12146-2 MO-12147-2 MO-12148-1
30 millimeter MO-12146-3 MO-12147-3 MO-12148-2
35 millimeter MO-12148-3

1T (inch) 2T (inch) 1T (millimeter) 2T (millimeter)

MO-04495 MO-04500 MO-05175 MO-05174
MO-04493 MO-04498 MO-05176 MO-05177
MO-04494 MO-04499 MO-05172 MO-05173

1T Alum

Use Catalog

number:

Size

1T Steel

Use Catalog

number:

1.2 CONTACT INFORMATION AND SERVICE ASSISTANCE

2T Steel

Use Catalog

number:

For service assistance, have the following information available:

• Type of Cartridge Transducer you are using

• Maximum wor k in g for c e

• Purchase order number

You can contact Cleveland Motion Controls at:

Phone:
Fax:

216.524.8800

216.642.5155

For the latest product information, technical literature etc., visit our website at www.cmccontrols.com

Disassembly by improperly trained personnel may result in additi onal damage to t hese units. Should repairs
be required or for warranty repairs, contact the Customer Service Department for a return authorization
number before returning the units.

1.3 RECEIVING AND UNPACKING

After receiving the Ultra Cantilever Transducer you should:

• Carefully, unpack and inspect the equipment

• Compare the received shipment with the packing list

• Report any damage to the carrier and your CMC representative

• Store equipment that will not be used in a clean, dry location

• Take appropriate precautions to prevent moisture, dust and dirt from accumulating in storage and

installation areas

PAGE 6 OF 18