Cleveland MKET-12-T Specifications

Cleveland

™

P

roject ________________________________

I

tem __________________________________

Quantity _______________________________

FCSI Section ____________________________

A

pproval _______________________________

D

ate __________________________________

1333 East 179 St.,

Cleveland, Ohio, U.S.A. 44110

Tel: [phone]

Fax: [phone]

Web Site: www.ClevelandRange.com

Email: [e-mail]

MIXER KETTLES

MIXER KETTLE, ELECTRIC
TABLE TYPE, TILTING
2/3 JACKETED

Cleveland Standard Features

n S

olid State temperature Control (±1°F) for perfect

simmering

n Solid State Low Water Safety Control

n Steam jacket filled with treated water, venting and/or refilling is

not required

n 50 psi safety valve mounted under kettle to avoid

tampering

n No water gauge required

n Rear mounted Pressure/Vacuum Gauge and Pressure Relief

Valve protected by Stainless Steel Bracket

n Infinitely variable speed for all conditions; scraper from 0-70

rpm, agitator from 0-210 rpm

n Removable (without tools) Nylon Blades scrape entire

jacketed surface

n 3/4 horse power D.C. Timing Belt Drive

n Safety Device prevents High Speed Starts

n Mixing stops when bridge is lifted

n Agitator and Scraper are bayonet mounted for easy removal

n Enclosed, balanced, 10 Gauge Stainless Steel Mixer Bridge

n Kettle and all exterior surfaces are Stainless Steel

n Large Pouring Lip

n Gallon Markers on Scraper Shaft

n Standard 120/208-240 volts, 60 Hz, 3 phase, 4 wire

ypical approvals include UL., CSA, CE, NSF and

n T

Options & Accessories

p Support Stand with Drain Drawer (ST28)

p Cover

p Double or Single Pantry Faucet (DPK or SPK)

p Faucet Bracket (FBKT)

p Food Strainer (FS-12)

p Flow Diverter (F-D)

p Kettle

(MTP12)

Accessory Kit (KAK) includes:

p Clean-up Brush (CB) p 36˝ Kettle Paddle (KP)
p 36˝ Kettle Whip (KW) p 36˝ Kettle Brush (KB)
p Draw-off Brush (DB) p 24 oz. Ladle (KL)

ASME

MODELS: c MKET-12-T

Short Form Specifications

Shall be CLEVELAND, Model MKET-12-T, Table Type Tilting, 12 Gallon,
Electric Mixer Kettle with permanently filled steam jacket, 50 psi jacket rat­ing and safety valve, Solid State Temperature (±1°F) and Low Water Safety
Controls, rear mounted Combination Pressure/Vacuum Gauge, infinitely vari­able speed, 3/4 H.P. Timing Belt Drive, bayonet mounted Agitator and
Scraper with r
mixing stops when bridge is lifted. Kettle and all exterior surfaces are
Stainless Steel.

p Type 316 Stainless Steel Kettle Interior for high acid food

products (316-12G)

p Water Meter (GMF or LMF) Wall Mounted or on Stand (SWM)

p High W

emovable blades, safety device pr

and Special Voltages (VOS)

attages

(HW)

events high speed star

SECT. XI PAGE 1

ts,

0707

TES

NO

:

Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Installation of backflow preventers, vacuum breakers and other specific coder requirements is the responsibility of the owner and installer.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are U.L., A.G.A., NSF, ASME/N.Bd., CSA, CGA, ETL and others.

(NOT TO SCALE)

SECT. XI PAGE 2

0707

Litho in USA