Cleveland MKET-10-T-SN1 Service Manual

Repair Manual

8251 Keele St. Concord, Ontario, Canada L4K 1Z1

Cleveland Range, Inc.

UNITED STATES CANADA

1333 East 179th St., Cleveland, Ohio 44110
Phone: [phone] Telex: 98-0546 Fax: [phone] Phone: [phone] Fax: [phone]
Toll Free: 1-800-338-2204 ( in U.S.A. only) Toll Free: 1-800-387-3562 ( in Canada only)

KET-11

Cleveland WARRANTY AND LIMITED EXTENDED

WARRANTY COVERAGE

LIMITED WARRANTY

Cleveland Range products are warranted to the original purchaser to be free from defects in material and workmanship

under normal use and service for the standard warranty period.

Cleveland Range agrees to repair or replace, at its option, f.o.b factory, any part which proves to be defective due to
defects in material or workmanship during the warranty period, providing the equipment has been unaltered, and has
been PROPERLY INSTALLED, MAINTAINED, AND OPERATED IN ACCORDANCE WITH THE CLEVELAND
RANGE OWNER'S MANUAL.

CLEVELAND RANGE agrees to pay any FACTORY AUTHORIZED EQUIPMENT SERVICE AGENCY (within
the continental United States, Hawaii, and Canada) for reasonable labor required to repair or replace, at our option, f.o.b.
factory, any part which proves to be defective due to defects in material or workmanship, during the labor warranty
period This warranty includes travel time not to exceed two hours and mileage not to exceed 50 miles (100 miles round­trip), but does not include post start-up, tightening loose fittings, minor adjustments, maintenance, cleaning or descaling.

The standard labor warranty allows factory payment of reasonable labor required to repair or replace such defective
parts. Cleveland Range will not reimburse the expense of labor required for the repair or replacement of parts after the
standard warranty period, unless an Extended Labor Warranty Contract has been purchased to cover the equipment for
the balance of the warranty period from the date of equipment installation, start-up, or demonstration

PROPER INSTALLATION IS THE RESPONSIBILITY OF THE DEALER, THE OWNER-USER, OR
INSTALLING CONTRACTOR. AND IS NOT COVERED BY THIS WARRANTY. Many local codes exist, and it is
the responsibility of the owner and installer to comply with these codes. Cleveland Range equipment is built to comply
with applicable standards for manufacturers, including UL, A.G.A., NSF, ASME/Ntl. Bd., CSA, CGA. ETL, and others.

BOILER (Steam Gener ator) MAINTENANCE IS THE RESPONSIBILITY OF THE OWNER-USER, AND IS NOT
COVERED BY THIS WARRANTY The use of good quality feed water is the responsibility of the Owner -User (see
Water Quality Requirements below). THE USE OF POOR QUALITY FEED WATER WILL VOID EQUIPMENT
WARRANTIES. Boiler maintenance supplies, including boiler hand gaskets, are not warranted beyond the first 90 days
after the date the equipment is placed into service if no preventive maintenance records are available showing descaling
every 90-120 days.

WATER QUALITY REQUIREMENTS

TOTAL DISSOLVED SOLIDS less than 60 parts per million
TOTAL ALKALINITY less than 20 parts per million
SlLICA less than 13 parts per million
CHLORIDE less than 30 parts per million
pH FACTOR greater than 7.5

The foregoing shall constitute the sole and exclusive remedy of original purchaser and the full liability of Cleveland
Range for any breach of warranty. THE FOREGOING IS EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, WHETHER WRITTEN, ORAL. OR IMPLIED. INCLUDING ANY WARRANTY OF
PERFORMANCE. MERCHANTABILITY, OR FITNESS FOR PURPOSE, AND SUPERSEDES AND EXCLUDES
ANY ORAL WARRANTIES OR REPRESENTATIONS, OR WRITTEN WARRANTIES OR REPRESENTATIONS,
NOT EXPRESSLY DESIGNATED IN WRITING AS A "WARRANTY" OR "GUARANTEE" OF CLEVELAND
RANGE MADE OR IMPLIED IN ANY MANUAL, LITERATURE, ADVERTISING BROCHURE OR OTHER
MATERIALS.

Cleveland Range's liability on any claim of any kind, including negligence, with respect to the goods or services
covered hereunder, shall in no case exceed the price of the goods or services, or part thereof, which gives rise to the
claim IN NO EVENT SHALL CLEVELAND RANGE BE LIABLE FOR SPECIAL. INCIDENTAL. OR
CONSEQUENTIAL DAMAGES. OR ANY DAMAGES IN THE NATURE OF PENALTIES.

LIMITED EXTENDED WARRANTY COVERAGE

The purchase of a Limited Extended Warranty Contract extends the standard war ranty coverage to the purchased period
of time (one to tour years) from the date of installation, start-up, or demonstration, whichever is sooner.

Revised 8/22/91

OPERATING CONTROLS AND
INDICATORS

Item No. Description Function

15 On-Off Toggle Switch (Control

Housing Dwg)

21 Solid State Temperature Control

Knob (Control Housing Dwg.)

17 Heat Indicator Light (Green)

(Control Housing Dwg.)

22 Low Water Indicator Light (Red)

(Control Housing Dwg.)

24 Agitator Speed Control Knob

(Control Housing Dwg.)

7 Vacuum/Pressure Gauge

(Kettle Bottom Dwg.)

5 Pressure Relief Valve

(Kettle Bottom Dwg.)

Controls electrical power to the kettle.

This control allows the operator to select kettle heat increments
from Mm to Max (see temperature setting chart in the

operating instructions manual).

When lit, indicates that the kettle heating elements are on

Cycles On-Off with temperature control.

When lit, indicates that the heating elements have shut off and

the unit requires more water (See Reservoir Fill Procedure).

This control allows the operator to select agitator speed

increments from Mm to Max.

Indicates steam pressure in PSI inside the steam jacket as well

as a vacuum.

In the unlikely event that there is an excess steam build-up in
the jacket, this valve opens automatically to relieve this

pressure.

1 Chrome Plated Brass Vent

(Kettle Bottom Dwg.)

12 Tilting Handle

(Kettle Bottom Dwg.)

This is used to vent the kettle if there is insufficient vacuum as
well as for refilling the kettle with water (See Venting

Instructions and Reservoir Fill Procedures).
Used for tilting the kettle.

KETTLE BOTTOM

Rev 1 (03/03/88)

Item No. Part No. Description Qty.

1 F105025 Bleed Vent Elbow-- 1
2 KE50570 Bleed Vent Nut 1
3 KE50556 Probe - Low Water 1
4 KE50997 Blow Down Tube 1
5 KE51723 Safety Valve, 50 PSI, 1/2 1

6 FI05022 Connector 1
7 KE50429 Pressure Gauge 1
8 KE00515 Thermistor 1
9 KE50558 Safety Thermostat (140°C) 1
10 KE50555 Gromet 1
11 KE50151 Knob, Handle 1
12 KE50803 Handle (MKET-10-T) 1

Use only replacement pans which are factory supplied as to preserve the certification of Underwriters Laboratories,

American Gas Association. Canadian Standards Association or Canadian Gas Association (as applicable). The use of other
than factory supplied replacement pans will void the warranty.

N/A Safety Valve, 55 PSI, 1/2' (please order pan 1

KE50561 Handle (M KET-20-T) 1

#KE51723)

Item No. Part No. Description Qty.

GEARBOX

1 FA95039 Dowel Pin, 1/4" x 2" (MKET-10-T) 2

FA95004 Dowel Pin, 3/8" x 3" (MKET-20-T) 2

2 FA11510 Screw, Socket Head Cap, 5/16-18 UNC x 1 -3/4" 4

FA10776 Screw, Socket Head Cap, 4

3/8-16 UNC x 2-1/2"

3 KE51966 Upper Body Casing (MKET-10-T) 1

KE50265 Upper Body Casing (MKET-20-T) 1
4 KE50268 Bushing, Small Gear 1
5 KE50266 Bearing, Small Gear 2
6 KE50259 Bearing, Large Gear 2
7 KE51245 Spacer (MKET-10-T) 1
8 KE50299 Gear, Large Spur (MKET-10-T) 1

KE00105 Gear, Large Spur (MKET-20-T) 1
9 FA95003 Key, Woodruff 2
10 KE00106 Gear, Small Spur 1
11 KE50264 Shaft, Driving 1
12 KE50261 Shaft, Driven (MKET-10-T) 1

KE50260 Shaft, Driven (MKET-20-T) 1
13 KE50269 Bushing, Large Gear 1
14 KE51967 Lower Body Casing (MKET-10-T) 1

KE50267 Lower Body Casing (MKET-20-T) 1
15 KE50342 Bushing, Taper Lock 1
16 KE50284 Pulley, Large 1

Use only replacement parts which are factory supplied as to preserve the certification of Underwriters Laboratories,
American Gas Association, Canadian Standards Association or Canadian Gas Association (as applicable). The use
of other than factory supplied replacement parts will void the warranty.