Cleode ZPLUG User Manual

S.A. au capital de 167 200 €

R.C.S. Saint Brieuc TGI 450 570 767

Siège social : 3 Rue Thomas Edison 22300 Lannion France

Tél. : [phone] – Fax : [phone]

ZigBee Power Plug

ZPLUG

User Manual

Révision 4.0
Document : UM_ZPLUG_20090903_001_04_00

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 2 sur 14

WARRANTY

The device supplied to the buyer and/or the recipient is guaranteed by CLEODE against any
malfunctions originating from a design and/or manufacturing flaw, for a period of twelve (12)
months following delivery. The buyer and/or recipient is (are) responsible for proving the
existence of the said defects or flaws. This warranty is applicable in accordance with articles
1641 to 1648 of the French Civil Code and in compliance with the French statutory warranty.
The warranty covers the replacement free of charge of devices and parts affected by a design
and/or manufacturing flaw excluding conspicuous defects in the device that are covered by
the buyer and/or the recipient.

In order to invoke the warranty, the buyer must immediately send written notice to CLEODE
of the flaws that it attributes to the device. It must enable CLEODE to have access to the
device to observe these defects and repair them. The warranty provided by CLEODE is
strictly limited to the equipment provided and shall only have for effect the replacement or
repair, at CLEODE’s expense, on its own premises, of all devices or parts that are not
functioning as a result of defects or flaws. CLEODE reserves the right to modify the devices
in order to comply with the warranty.

The warranty does not apply to replacement or repairs that may result from normal wear and
tear of devices, systems or products, damage or accidents resulting from negligence, failure to
supervise or maintain, or incorrect use of the devices, systems and/or products.

The maintenance service is provided by CLEODE with all reasonable care possible and in
compliance with the current state of the arts.

The exchange of parts or repairs performed under the warranty cannot result in extending the
length of the warranty. In no event can the unavailability of the device due to servicing give
rise to compensation for any reason whatsoever. The seller is released from all obligations
relating to the warranty if the product or device has been modified without prior written
consent, or if original parts have been replaced by parts which it has not manufactured
without prior consent. If unforeseen damage is caused by the device, it is expressly agreed
that the seller can only be liable for the reimbursement of monies received for the purchase of
the device if it has been destroyed. Under no circumstances can the seller be held liable for
indirect or contingent damage. The seller is released from any liability and the buyer waives
any rights against it if an accident or direct or indirect damage is caused to the buyer
following a defect, incorrect usage, incorrect maintenance or normal wear of the device sold.

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 3 sur 14

TABLE OF CONTENT

WARRANTY ......................................................................................................................................... 2

REFERENCE DOCUMENTS ............................................................................................................. 6

I INTRODUCTION ........................................................................................................................... 7

I.1 ZPLUG PRESENTATION ............................................................................................................... 7

I.2 COPYRIGHT ................................................................................................................................... 7

II ZPLUG DESCRIPTION ............................................................................................................... 8

II.1 ZIGBEE PRESENTATION .............................................................................................................. 8

II.2 DESCRIPTION OF THE AVAILABLE INFORMATION .................................................... 8

II.2.1 DESCRIPTION OF THE APPLICATION ............................................................................................ 8

II.2.2 CLUSTERS DESCRIPTION.............................................................................................................. 9

III INSTALLATION AND WORKING ........................................................................................ 11

III.1 INSTALLATION.......................................................................................................................... 11

III.2 WORKING ................................................................................................................................. 11

III.2.1 ON/OFF SWITCHING ................................................................................................................. 11

III.2.2 RESET ZPLUG ........................................................................................................................ 11

III.2.3 SCAN OF THE NETWORK .......................................................................................................... 11

IV TECHNICAL FEATURES ........................................................................................................ 12

REPAIR AND MAINTENANCE ...................................................................................................... 13

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 4 sur 14

LIST OF FIGURES

Figure 1 : ZPLUG presentation .................................................................................................. 7

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 5 sur 14

TABLE OF REVISIONS

Version

Authors(s)

Version description

Date

0.1

CLEODE

Initial version

03/09/2009

1.0

CLEODE

Validated document

08/09/2009

1.1

CLEODE

Add Technical features chapter

24/09/2009

2.0

CLEODE

Validated document

24/09/2009

2.1

CLEODE

Updated for the new design

07/09/2011

3.0

CLEODE

Validated document

07/09/2011

3.1

CLEODE

Updated for the amplified signal

09/10/2012

4.0

CLEODE

Validated document

09/10/2012

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 6 sur 14

REFERENCE DOCUMENTS

N°

Document

Description

[1]

ZigBee_Cluster_Library_Public

Zigbee Cluster Library specification

[2]

ZigBee_Home_Automation_Profile

Home Automation profile specification

[3]

ZigBee_Specification

ZigBee Specification

[4]

ZigBee_Smart_Energy_Profile

Zigbee Smart Energy profile specification

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 7 sur 14

I INTRODUCTION

I.1 ZPLUG PRESENTATION

The ZigBee™ AC 220V plug ZPLUG™ is a module the user can plug on directly in standard
220VAC outlets (C, E or F type) for 3500W max appliance.
It is able to monitor how much electricity an appliance plugged into it is using.

The ZPLUG has this form:

Figure 1 : ZPLUG presentation

I.2 COPYRIGHT

The CLEODE trademark and the CLEODE logo are properties of CLEODE SA, France. This
document also refers to trademarks and other product names that are registered trademarks of
their respective owners.
Copyright © 2009 CLEODE SA. All rights reserved.

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 8 sur 14

II ZPLUG DESCRIPTION

II.1 ZIGBEE PRESENTATION

The ZPLUG contains an application with :

 Switching on/off the appliance plugged into the plug. This is based on the

MainPowerOutlet application defined in the ZigBee Home Automation profile.

 The measure of the consumption of the appliance plugged into the plug. The power

socket can accept devices up to 3500 watts.

For more detail on the data exchange between device and network, see documents [1], [2], [3]
and [4].

The ZPLUG embedded the router functionality with amplified signal up to + 20 dBm. This
means that the ZPLUG is able to extend the ZigBee Network.

II.2 DESCRIPTION OF THE AVAILABLE INFORMATION

The switching is made by sending a command On/Off on the On/Off cluster.

The simple metering is used to monitor how much electricity an appliance plugged into it is
using. This application is able to send the current demand of energy in KW and the most
recent summed value of energy used in KWh.

II.2.1 DESCRIPTION OF THE APPLICATION

 Device ID : Mains Power Outlet
 Endpoint : 1
 Clusters :

Côté serveur

Côté client

Basic (0x00)

/

Identify (0x03)

/

Groups (0x04)

/

Scenes (0x05)

/

On/Off (0x06)

/

Simple Metering (0x0702)

/

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 9 sur 14

II.2.2 CLUSTERS DESCRIPTION

This is a terse description of clusters and attributes implemented in the switch ZigBee ™. For
more precision on the functioning of these, would like refer to documents [1] and [4].

 Basic cluster :
This cluster is used to determine basic information about the device.

Attribute

Attribute ID

ZCLVersion

0x0000

ApplicationVersion

0x0001

StackVersion

0x0002

HWVersion

0x0003

ManufacturerName

0x0004

ModelIdentifier

0x0005

DateCode

0x0006

PowerSource

0x0007

LocationDescription

0x0010

PhysicalEnvironment

0x0011

DeviceEnabled

0x0012

AlarmMask

0x0013

 Cluster Identify :
This cluster is used to identify physically the object in the network. On writing of the
value of the attribute IdentifyTime the LED of the object is going to flash during the time
specified by this value.

Attribute

Attribute ID

IdentifyTime

0x0000

 Cluster Groups:
This cluster allows to storing the name of the groups to which Zplug belongs.

Attribute

Attribute ID

NameSupport

0x0000

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 10 sur 14

 Cluster Scenes:
This cluster allows to managing the scene of which is a part Zplug.

Attribute

Attribute ID

SceneCount

0x0000

CurrentScene

0x0001

CurrentGroup

0x0002

SceneValid

0x0003

NameSupport

0x0004

 On/Off cluster:
This cluster is used to switching the device between On and Off states.

Attribute

Attribute ID

On/Off

0x0000

 Cluster Simple Metering :
The attributes of the cluster Simple Metering implemented in the power plug:

Attribute

Attribute ID

CurrentSummationDelivered

0x0000

Status

0x0200

UnitofMeasure

0x0300

Multiplier

0x0301

Divisor

0x0302

SummationFormatting

0x0303

DemandFormatting

0x0304

MeteringDeviceType

0x0306

InstantaneousDemand

0x0400

Two attributes of SimpleMetering send periodic reports :

 CurrentSummationDelivered : represents the most recent summed value of Energy in

Kwh.

 InstantaneousDemand : represents the current Demand of Energy in Kw.

These used reports mechanisms described the document [1].

Every 12 hours, the value of CurrentSummationDelivered is store in memory, it allows in
case of power cut to keep this value.

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 11 sur 14

III INSTALLATION AND WORKING

III.1 INSTALLATION

The user has to plug the ZPLUG on a socket in the wall and plug the appliance on it.

At plugging, the ZPLUG sends beacon request on the network. If a ZigBee coordinator or
router is able to associate the ZPLUG the ZPLUG enters in the network.

III.2 WORKING

III.2.1 ON/OFF SWITCHING

The first time the ZPLUG is plugged in the socket, the switch is ON.

In each switching, the ZPLUG keeps the value of the attribute ON / OFF in memory not
volatile. Consequently, if a power cut or a disconnection of the ZPLUG arrives, this one will
find the state of switching in the restart.

This switching can take place of two different ways:

 By pressing on the present button in facade,
 By sending a command on ZPLUG by the connection ZigBee.

When the output of the ZPLUG is fed, the LED of the ZPLUG is lit in red otherwise it is put
out.

III.2.2 RESET ZPLUG

To make a reset of the network parameters of Zplug, you have to press on the button during at
least 5s.

III.2.3 SCAN OF THE NETWORK

If your Zplug does not find a network available ZigBee it will make automatically a new scan
at the end of 15 minutes. This time will increase twofold every time the ZPLUG makes a scan
without finding of available network.

If you wish to boost a scan of the network manually you have to press during 3 seconds on the
button of the ZPlug, this will have the effect of making the LED of the ZPLUG flash. If your
ZPlug is already associated, presses it during 3 seconds on the button will have no effect

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 12 sur 14

IV TECHNICAL FEATURES

Weight

150 g

Power Supply

220V French standard

Accuracy Measurement

±1 % of full scale

Commutation

Up to 16A on 220V

Transmission range

300 m outdoor
90 m indoor

Output Power

Up to + 20dBm

Managed channels (frequency)

16 channels ZigBee™ (2.405 à 2.480 GHz)

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 13 sur 14

REPAIR AND MAINTENANCE

Defective equipments shall be first reported to the CLEODE support team in order to be
assigned an RMA number. Be prepared to state your name, company and the serial number of
the defective item to the support personnel.

The item shall then be returned to CLEODE with the following documents:

 The RMA number
 A copy of the delivery slip
 A detailed description of the default and the test context

The maintenance period is typically four (4) weeks starting from the date of reception of the
equipment at the CLEODE headquarters.

Remark : A FAQ (Frequently Asked Questions) is available on the www.cleode.com web site.

User Manual – ZPLUG

UM_ZPLUG_20090903_001_04_00.doc CLEODE Page 14 sur 14

CLEODE S.A.

Technical Support Division

3 Rue Thomas Edison

22300 Lannion

France

Phone : [phone]

Fax : [phone]

E-mail : [e-mail]

Web : http://www.cleode.com