S Operator’s Manual and Installation Guide:
Machine to Machine
0 Wireless Network Range Extender is a high performance, microprocessor controlled,
bidirectional RF amplifier for the entire North American 850 MHz cellular and 1900 MHz PCS frequency
bands. The amplifier has an automatic gain and oscillation control syst
the gain and the output power if a signal anomaly occurs. This amplifier is designed to operate as a
tethered (direct connect) unit within a cellular system, for maximum performance in weak signal
power requirements for the amplifier are positive 8.0 to 36.0 volts DC
it includes an AC power adapter for use with typical household 120 volt
Passive Bypass Technology
ped with ClearRF’s Passive Bypass technology. This feature allows the
amplifier to passively bypass itself and become merely a pass through cable when amplification is not
needed, during loss of power or when a faul
is useful in applications where the amplifier is mobile
. The amplifier will bypass itself when close to cell towers, completely eliminating any
potential for network disrupting noise power caused by too much amplific
technology is also extremely useful in fire and security system installations where a connection with the
antenna must always be maintained, even with loss of power.
em that will automatically adjust
,
ation near a cell tower. The
™
WRE2710-
M2M –
Overview
The WRE271
coverage areas. The input
(negative ground). This M2M k
AC power.
The WRE2710 amplifier is equip
– Patent Pending
t is detected.
Passive Bypass technology
poor signal areas
MAN-5446-001 Rev 6
moving in and out of
1
Contents
................................
Patent Pending
................................
................................
Installation with an SMA Device
Installation with an MMCX Device
Installation with an SMA Device
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
................................
Overview ................................
................................
................. 1
Passive Bypass Technology –
Parts List ................................
Installation Guide
LED Diagnostics
Diagnostic LED definitions
Optional Accessories
WRE-2710 Specifications
Safeguard Features
Antennas ................................
Warranty Information
................................
................................
................................................................
- Fixed Location ................................
- Fixed Location ................................
- Mobile Location ................................
................................................................
................................
................................
................................
................................
................................
................................
........................... 1
................. 3
.... 3
.............. 4
........... 6
............ 7
....... 8
....................... 9
............................... 9
....................... 10
................................ 12
............... 12
........................... 12
MAN-5446-001 Rev 6
2
Parts List
Depending upon the connector type of the cellular device, ClearRF can customize the M2M kit to include
the appropriate adapters to ensure a
SMA, MMCX, MCX, FME
1. WRE271
0 Amplifier Unit
3. Hardwire DC Power Cable
5. SMA
-to-
SMA Device Cable
: Installation of this device requires knowledge of basic electrical and
experience with installing electronic devices. We recommend seeking a
professional installer if you are not accustomed to installing electronics or high
Installation of this de
assumes no responsibility for the installation or improper operation of this
device. Contact your dealer or
Help” in the subject line for assistance.
and quick installation. Adapter types include
2. AC/DC Power Adapter
4. Magnetic
-
Mount Outdoor Signal
–If
connecting to
6. Optional
–
SMA
-
to
If connecting to an MMCX device.
vice is at your own risk. Clear
.com
-
MMCX Device Cable
–
limited to SMA, RP-
seamless
, and TNC.
, but are not
Antenna
an SMA device
Installation Guide
Disclaimer
tech devices.
MAN-5446-001 Rev 6
CustomerService@ClearRF
RF, LLC
with “Installation
3
Installation with an SMA Device
a Cellular Modem (
) to the ClearRF Amplifi
), connect the TNC to SMA
1. If connecting to
(#5 on Parts List
- Fixed Location
e.g. Raven X, CradlePoint
er connector marked “Device”.
device cable
MAN-5446-001 Rev 6
4
2.
Connect the SMA end of the TNC to SMA
Outdoor Signal A
Outdoor Signal
(#2 on Parts List)
connector
able to the Cellular Modem
vertically on any metal surface.
ClearRF amplifier
plug into the amplifier and watch the LED indicators.
connection.
3. Mount the
device c
ntenna (#4 on Parts List)
antenna
a. Connect the
marked “Antenna”.
4. Plug the AC Adapter
5. Insert the AC Adapter
Antenna connector to the
into a nearby wall outlet.
TNC connector
MAN-5446-001 Rev 6
5
Installation with an M
MCX Device
Module
on Parts List) to the ClearRF Amplifier connector marked “
end of the
Mount the Outdoor Signal Antenna (#4 on Parts List) vertically on any metal surface.
the Outdoor Signal Antenna connector to the ClearRF amplifier
Plug the AC Adapter (#2 on Parts
), connect the
Device
able to the Cellular M
1. If connecting to a Cellular
device cable (#6
2. Connect the MMCX
3.
- Fixed Location
(e.g. Motorola, Sierra Wireless
SMA to MMCX device c
SMA-to-MMCX
.”
odule.
4. Connect
“Antenna”.
5.
MAN-5446-001 Rev 6
SMA connector marked
List) into a nearby wall outlet.
6
6.
Insert the AC Adapter connector plug into the amplifier and watch the LED indicators.
Installation with an SMA Device
If connecting to a Cellular Modem
ile application, connect the SMA
Amplifier connector marked “Device”.
Connect the SMA end of the
(e.g. Raven X, etc
to SMA device cable (#5 on Parts List) to the ClearRF
SMA device cable to the Cellular Modem
1.
mob
- Mobile Location
or Mobile Data Terminal
) in a vehicle or
2.
connection.
SMA-to-
or MDT antenna
MAN-5446-001 Rev 6
7
3. Mount
the Outdoor Signal Antenna (#4 on Parts List) vertically on any metal surface on the roof,
hood or trunk of the vehicle.
the Outdoor Signal Antenna connector to the ClearRF amplifier
Plug the 12V Hardwire DC Cab
the red wire to a positive terminal from the fuse panel with a 3 ampere fuse rating. The black
wire should be attached to a ground of the vehicle. Power may also be provided to the amplif
using a 12V cigarette lighter adaptor. (not included, available at www.clearrf.com)
Hard Wire DC Cable
Once the amplifier is installed properly and power
the green LED flashing. The green LED will flash while the amplifier increases its gain to the optimum
level. The red LED may also flash during this stage while the gain (power) is properly set on the
ifier. When power control is established, the green LED will remain constantly on. You may see
le (#3 on Parts List) into the vehicle fuse block. You must connect
connector plug into the amplifier and watch the LED indicators.
he LEDs will both turn on followed by
b. Connect
marked “Antenna”.
4.
SMA connector
5. Insert the
LED Diagnostics
ampl
ier
is applied, t
MAN-5446-001 Rev 6
8
the green and red LEDs flash back and forth, THIS IS NORMAL. In areas where the cellular network is
adequate, the amplifier will maintain a maximum power level a
prevent overloading the wireless phone, as well as keeping RF signal levels at a minimum for a
healthy environment.
If the red LED is constantly on and the green LED is off, the amplifier has
The amplifier will
reposition the antenna until normal operation is achieved.
you may permanently mount the antennas in the locations you chose in the prio
Diagnostic LED definitions
LED test, the unit is initializing
Normal operation
Normal operation, increasing gain setting
Solid Green and Flashing Red
nd no Green
for pricing and availability or see your Clear RF
parts and additional accessories may also be avai
cceptable for normal operation and
automatically and restart. If the fault persists,
Once normal operation is established,
Normal operation, decreasing gain setting
power is cycled.
detected a fault.
1. Solid Green and Red –
2. Solid Green –
3. Flashing Green –
4.
5. Solid Red a
Optional Accessories
Contact us at www.clearrf.com
shut down
-
–
– Fault detected (Unit will shut down until
lable.
r steps.
)
™
dealer. Replacement
MAN-5446-001 Rev 6
9
WRE
2710 Specifications
Frequency Range: Cellular 850 (824MHz
20dB BW: 850 UL: 39MHz, 1900 UL: 115MHz
Rated Uplink Maximum Output Power: Cellular 850; 27dBm, PCS 1900; 27dBm
Rated Downlink Maximum Output Powe
Current Draw @ 12VDC: Idle: 250 milliamperes; Max: 1 amperes
Power Requirement: 8.0 to 36.0 volts DC (negative ground), Connector is center positive
Nominal Gain: Cellular 850: 15dB, PCS 1900: 15dB
pedance: 50 Ohms
Rated Mean Output Power: 27dBm
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1
device may not cause harmful interference, and (2
interference that may cause undesired operation.
The term “IC:” before the radio certification number only signifies that Industry of Canada technical
The Manufacturer'
operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5
dB, especially where the output signal is re
power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of
La puissance de sortie nominale indiquée par le fabricant pour cet appareil concerne son fonctionnement avec
porteuse unique. Pour des appareils avec porteuses multiples, on doit réduire la valeur nominale de 3,5 dB,
surtout si le signal de sortie est retransmis et qu'il peut causer du brouillage aux utilisateurs de bandes
adjacentes. Une telle réduction doit po
moyen d'un atténuateur raccordé à la sortie du dispositif.
FCC Regulatory Guidance: ClearRF’s WRE2710
ions Commission (FCC). For more information
225
894MHz), PCS 1900 (1850MHz
dBm, PCS 1900;
device must accept any interference received, including
s rated output power of this equipment is for single carrier
adjacent band users. This
rter sur la puissance d'entrée ou sur le gain, et ne doit pas se faire au
S operates under the rules and regulations as provided by the
these rules and regulations, please
•
–
– 1990MHz)
•
•
•
•
•
•
• Input/output Im
•
FCC ID: XS7-WRE2710
IC ID: 8918A-WRE2710
r: Cellular 850; -20
) this
-20dBm
) this
specifications were met.
the device.
Federal Communicat
contact the FCC directly at (888)-
-radiated and can cause interference to
on
-5322.
MAN-5446-001 Rev 6
10
MAN-5446-001 Rev 6
11
Safeguard Features
The amplifier has an automatic gain and oscillation control system that will automatically adjust
ain and the output power if a signal anomaly occurs. This amplifier is designed to operate as a
tethered (direct connect) unit within a cellular system, for maximum performance in weak signal
You MUST operate this device with app
manufacturer. Antennas MUST be installed as least 20 cm (8 inches) from any person.
-
SMA
Warranty Information
ClearRF L.L.C. warrants that this product is free from defects in materials or workmanship for one year from the date of purc
Within this period, ClearRF, will, at its sole option, repair or replace any components which fail in normal use. S
replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for
transportation cost. This warranty does not cover failures due to abuse, misuse, accident or unauthorized alter
Repairs have a 90 day warranty. If the unit sent in is still under its original warranty, then the new warranty is 90 days or
of the original one year warranty, depending upon which is longer.
ht to repair or replace the product or offer a full refund of the purchase price at its sole discretion.
Such remedy shall be your sole and exclusive remedy for any breach of warranty. ClearRF shall not be liable for any incident
Procedure for Claims under Limited Warranties
To obtain warranty service, an original or copy of the sales receipt from the
To obtain warranty service, follow these two steps:
Contact ClearRF via email to
Once you have obtained an RMA #, ship the unit, copy of the sales receipt, along with the RMA
, Suite 104
roved antennas and cables as specified by the
original retailer is required.
receive authorization (RMA) number at warranty@clearrf.com
the g
coverage areas.
Antennas
Included Antenna: MSE
Included Cable: CBL-
ClearRF retains the exclusive rig
consequential damages for breach.
5721-001 Mag Mount Antenna
-SMA or CBL-SMA-MMCX
Limited Warranty
uch repairs or
ations or repairs.
hase.
any
to the end
al or
1.
2.
number to:
ClearRF
RMA #: {insert RMA number}
12825 E. Mirabeau Parkway
Spokane Valley, WA 99216
855-321-9527
MAN-5446-001 Rev 6
12
Loading...