ClearOne COLLABORATE Room Installation And Setup Manual

COLLABORATE
I

NSTALLATION AND SETUP MANUAL

®

ROOM

ClearOne
5225 Wiley Post Way
Suite 500
Salt Lake City, UT 84116

Telephone [phone]

1.801.974.3760

Tech Sales 1.800.705.2103

FAX [phone]

E-mail [e-mail]

[e-mail]

On the Web

www.clearone.com
www.netstreams.com
www.streamnetpartners.com

COLLABORATE Room

INSTALLATION AND SETUP GUIDE

LEARONE DOCUMENT

C
DOC-0077-001

© 2013 ClearOne and NetStreams - All rights reserved. No part of this
document may be reproduced in any form or by any means without written
permission from ClearOne and NetStreams. Printed in the United States of
America. ClearOne and NetStreams reserves specific privileges.

Information in this document is subject to change without notice.

REV. 1.2 – MARCH 2013

WARNING: This is a class A product. In a domestic environment
this product may cause radio interference in which case the user
may be required to take adequate measures.

© 2004 - 2013 ClearOne. All Rights Reserved.

Information in this document is subject to change without notice. No part of this document
can be reproduced or transmitted in any form or by any means - electronic or mechanical ­for any purpose without written permission from ClearOne.

ClearOne and COLLABORATE Central are registered trademarks of ClearOne.

All other trademarks are the trademarks of their respective companies.

CAUTION! To comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules, all cables used to connect
the system and peripherals must be shielded and grounded.
Operation with non-shielded cables may result in interference to
radio or television reception.

Overview Safety Information

Safety Information

CAUTION! Do not open the COLLABORATE Room unit. There are
no user-serviceable parts inside. Opening the unit voids the
warranty and can also cause injury. Please refer servicing to
ClearOne-trained service personnel.

When you use a COLLABORATE Room system, observe the following safety guidelines:

DANGER! The internal areas of the unit and auxiliary equipment are
sources of voltage that, if not handled properly, constitute danger
of bodily harm. DO NOT operate the unit with any of its covers
(including main cover, bezels, filler brackets, front-panel inserts,
and so on) removed. INCORRECT replacement of the Remote
Control battery can cause an explosion. Replace only with the
same or equivalent-type of battery recommended by the
manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.



Make sure that the power is turned off and all equipment is disconnected from the
power supply before making any equipment connections.



Make sure the monitor and attached accessories (PTZ camera, VCR, document
camera, and so on) are electrically rated to operate with the AC power available in your
location.



To help prevent electric shock, plug the unit and accessories’ power cables into
properly grounded power sources. These cables are equipped with three-prong plugs
to help ensure proper grounding. Do not use adapter plugs or remove the grounding
prong from a cable. If you must use an extension cable, use a three-wire cable with
properly grounded plugs.



Make sure that nothing rests on the unit system’s cables and that the cables are not
located where they can be stepped on or tripped over.



Do not install this equipment near water, or in an otherwise wet or damp environment.



Do not run the equipment in an environment with ambient temperature higher than 35°C
or lower than 10°C.



Keep food and liquids away from the system or accessories.



Keep the unit away from radiators and heat sources. Also, do not block cooling vents.
Avoid placing loose papers underneath the unit, and do not place the system in a
closed-in wall unit or on a bed, sofa, or rug.



Do not install or operate this equipment if chemical gas leakage is expected in the area.



Close supervision is necessary when the system is used by or near children. Do not
leave unattended while in use.



Before cleaning the appliance, unplug the power cord. Use only a soft cloth dampened
with water for cleaning.



Do not place this product on an unstable surface or support. The product may fall,
causing serious injury to a child or adult, as well as serious damage to the product.



Do not use the appliance outdoors.



Do not disassemble or open the appliance. Failure to comply will void the warranty.



Do not use any accessories other than those approved by ClearOne. Failure to do so
may result in loss of performance, damage to the product, fire, electric shock or injury,
and will void the warranty.



Connect the system only to a surge protected power outlets.



Do not connect or disconnect power supply cables and data transmission lines during
thunderstorms.



Do not overload wall outlets or extension cords, as this can result in a risk of fire or
electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged
or cracked wire insulation, and broken plugs are dangerous. They may result in a shock
or fire hazard. Periodically examine the cord, and if its appearance indicates damage or
deteriorated insulation, have it replaced by your service technician.



If the unit or any part of it is damaged, disconnect the power plug and inform the
responsible service personnel. Nonobservance may result in damage to the appliance.

Consignes de sécurité

ATTENTION! : N'ouvrez pas l'unité COLLABORATE Room. Elle ne
comporte aucune pièce pouvant être entretenue par l'utilisateur.
L'ouverture de cette unité rend la garantie caduque et est
susceptible d'occasionner des blessures. Pour les services
d'entretien veuillez vous adresser au personnel du service clientèle
ClearOne formé à cet effet.

6 COLLABORATE Room: Installation and Setup Guide

Lors de l'utilisation d'un système COLLABORATE Room, veuillez respecter les consignes de
sécurité suivantes :

DANGER! Les parties internes de l'unité et l'équipement auxiliaire
sont sous tension et s'ils ne sont pas manipulés correctement
peuvent représentant un danger de dommage corporel. Ne pas
faire fonctionner l'unité si l'un de ses couvercles (y compris le
couvercle principal, lunettes, plaques de fixation de remplissage,
encastrement du panneau avant) est retiré. Un remplacement
incorrect de la batterie de la télécommande est susceptible
d'entraîner une explosion. Remplacez les batteries usagées
uniquement par le même type de batteries que celles
recommandées par le fabricant ou des batteries équivalentes.
Débarrassez-vous des batteries usagées conformément aux
instructions du fabricant.



Assurez vous que l'alimentation électrique est coupée et que tout l'équipement est
déconnecté du réseau électrique avant d'effectuer toute connexion de l'équipement.



Assurez vous que l'écran et les accessoires qui lui sont joints (caméra PTZ,
magnétoscope, caméra de document etc.) sont réglés pour fonctionner avec le courant
CA disponible sur les lieux.



Pour éviter tout choc électrique, branchez les câbles d'alimentation de l'unité et des
accessoires à des prises convenablement mises à terre. Ces câbles sont équipés de
prises mâles à trois broches pour vous aider à garantir une mise à terre correcte.
N'utilisez aucune fiche d'adaptation et ne retirez aucune fiche de mise à terre des
câbles. Si vous devez utiliser une rallonge, utilisez un câble à trois fils équipé des prises
de terre adéquates.



Assurez vous que rien n'est posé sur les câbles de l'unité du système et que les câbles
ne sont pas placés à un endroit où l'on peut marcher ou trébucher dessus.



Ne pas installer cet équipement près d'un point d'eau ou dans un milieu humide ou
mouillé.



Ne pas utiliser l'équipement dans un environnement dont la température ambiante
dépasse 35°C ou est inférieure à 10°C.



Eloignez tout aliment ou liquide du système ou de ses accessoires.



Eloignez l'unité des radiateurs et sources de chaleur. Ne pas bloquer les fentes
d'aération. Evitez de placer des feuilles de papier libre sous l'unité et d'encastrer le
système dans unité murale fermée ou de le poser sur un lit, sofa ou tapis.



Ne pas installer ou faire fonctionner cet équipement si une fuite de gaz chimique est
prévue dans la région.



En cas d'utilisation du système à proximité d'enfants ou par des enfants, une
surveillance rapprochée sera requise. Ne pas laisser l'équipement sans surveillance
pendant son utilisation.

COLLABORATE Room: Installation and Setup Guide 7



Avant de nettoyer l'appareil, débranchez le cordon d'alimentation. Pour le nettoyage,
utilisez exclusivement un chiffon doux humidifié.



Ne pas placer ce produit sur une surface ou un support instable. Le produit pourrait
tomber et occasionner de graves dommages à un enfant ou à un adulte et être lui­même sérieusement endommagé.



Ne pas utiliser l'appareil à l'extérieur.



Ne pas démonter ou ouvrir l'appareil. Faute de quoi la garantie deviendrait caduque.



Ne pas utiliser d'autres accessoires que ceux agréés par ClearOne. Dans le cas
contraire, les performances de l'appareil sont susceptibles d'être affectées, et un pareil
usage pourrait occasionner un dommage au produit, provoquer un incendie, un choc
électrique ou une blessure et rendrait la garantie caduque.



Ne connecter le système qu'à des prises d'alimentation protégées contre la surtension
transitoire.



Ne pas connecter ou déconnecter les câbles d'alimentation et lignes de transmission
de données pendant un orage.



Ne pas surcharger les prises murales ou rallonges, vous risqueriez de provoquer un
incendie ou un choc électrique. Les prises CA et rallonges surchargées, les fils
d'alimentation abîmés, une isolation défectueuse des câbles et des prises mâles
endommagées sont dangereux. Ils peuvent occasionner des incendies ou chocs.
Examinez régulièrement le cordon et s'il présente un dommage ou une isolation
défectueuse faites le remplacer par le technicien responsable de l'entretien.



Si l'unité ou toute pièce de l'unité est endommagée, débranchez la prise d'alimentation
et informez le personnel responsable de l'entretien. Dans le cas contraire vous risquez
d'endommager l'appareil.

Power Adapter



Operate this product only from the type of power source indicated on the product’s
marking label. If you are not sure of the type of power supplied to your home, consult
your dealer or local power company.



Use only the power supply provided with your product. Check whether the device’s set
supply voltage is the same as the local supply voltage.



To reduce risk of damage to the unit, remove it from the outlet by holding the power
adapter rather than the cord.

Adaptateur de courant



N'utilisez ce produit qu'avec la source d'alimentation indiquée sur l'étiquette du produit.
Si vous n'êtes pas sûr du type d'alimentation électrique de votre domicile, consultez
votre fournisseur ou la compagnie d'électricité locale.



Utilisez exclusivement l'alimentation électrique fournie avec votre produit. Vérifiez que le
réglage de la tension d'alimentation de votre appareil correspond à la tension
d'alimentation locale.

8 COLLABORATE Room: Installation and Setup Guide



Afin de minimiser les risques de dommages à l'unité, débranchez-là en tenant
l'adaptateur de courant plutôt que de tirer sur le cordon.

Remote Control

Télécommande

Produit à diodes électroluminescentes (DEL) de classe 1.

FCC Warning

Modifications not expressly approved by the manufacturer could void the user authority to
operate the equipment under FCC rules.

The FCC Wants You to Know

This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.

This equipment can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at his own expense.

Declaration of Conformity for Terminal Equipment

Issued according to ISO/IEC Guide 22 and EN45014 under the sole responsibility of the
Manufacturer

We hereby declare entirely on our own responsibility that the products:

Product Name:
COLLABORATE Room SYSTEM

and all its associated peripherals manufactured by ClearOne, to which this declaration
relates is in conformity with:

COLLABORATE Room: Installation and Setup Guide 9

European Community

With the essential requirements specified in Article 3.1 (a) and 3.1 (b) of:

Directive 2004/108/EC (EMC Directive).
Directive 2006/95/EC (Low Voltage Directive – LVD).
Directive 1999/5/EC (Radio Equipment and Telecommunications Terminal Equipment
Directive).

In accordance with the following Harmonized Standards­The products are compliant with the following standards and other normative documents:
EMC: EN 55022: 1998 +A1: 2000 +A2: 2003 Class A
EN 55024: 1998 +A1: 2001 +A2: 2003
EN 61000-3-2: 2000 Class A
EN 61000-3-3: 1995 +A1: 2001
IEC 61000-4-2: 2001
IEC 61000-4-3: 2002
IEC 61000-4-4: 1995 +A1:2000 +A2: 2001
IEC 61000-4-5: 2001
IEC 61000-4-6: 2001
IEC 61000-4-11: 2001
Safety / Low Voltage: EN 60950
IEC 60950
Telecom (ISDN Point only): CTR3

Regulatory Notice to European Customers
The "CE" mark is affixed to this product to demonstrate conformance to the R&TTE Directive
1999/5/EC (Radio Equipment and Telecommunications Terminal Equipment Directive).

USA & Canada

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation

The products are compliant with the following standards and other normative documents:

EMC: FCC Part 15, Class A

Safety / Low Voltage: CS 22.2 950
UL 60950

Telecom (ISDN Point only): FCC Part 68
CS-03 Issue 9

10 COLLABORATE Room: Installation and Setup Guide

Federal Communications Commission Radio Frequency Interference Statement all products

- COLLABORATE Room - comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Shielded cables must be used with this equipment to maintain compliance with FCC
regulations.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.

Part 68 FCC Rules

This equipment (the ISDN Point which is part of only some of COLLABORATE Room
Models) complies with part 68 of the FCC rules and the rules adopted by the ACTA.
This equipment may not be used on a coin service or party line.
If you experience trouble with your COLLABORATE Room system, disconnect it from the
telephone line to determine if the registered equipment is malfunctioning.
Your telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of your equipment. If they do, you will be given
advance notice so that you may make any changes necessary to maintain uninterrupted
service.

Industry Canada (IC)

This Class [A] digital apparatus complies with Canadian ICES-003.

The Industry Canada label identifies certified equipment. This certification means that the
equipment meets telecommunications network protective, operational and safety
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The Department does not guarantee the equipment will operate to the user's
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be
installed using an acceptable method of connection. The customer should be aware that
compliance with the above conditions may not prevent degradation of service in some
situations. Repairs to certified equipment should be coordinated by a representative
designated by the supplier. Any repairs or alterations made by the user to this equipment,
or equipment malfunctions, may give the telecommunications company cause to request
the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines and internal metallic water pipe system, if present, are
connected together. This precaution may be particularly important in rural areas.

CAUTION: Users should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.

COLLABORATE Room: Installation and Setup Guide 11

The Ringer Equivalence Number (REN) assigned to each relevant terminal device
provides an indication of the maximum number of terminals allowed to be connected to a
telephone interface. The termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the RENs of all the devices does not
exceed 5.
The REN is useful to determine the quantity of devices that may be connected to the
telephone line. Excessive RENs on the telephone line may result in the devices not ringing
in response to an incoming call. In most, but not all areas, the sum of RENs of all devices
that may be connected to a line, is determined by the total RENs, contact the local
telephone company.

Industrie Canada (IC)

Cet appareil numérique de classe A répond à la norme canadienne ICES-003

Le label Industrie Canada identifie les équipements certifiés. La certification signifie que
l'équipement répond aux exigences de sécurité, de fonctionnement et de protection de
réseaux de télécommunications prescrits par le/les document/s d'Exigences Techniques en
matière d'équipement terminal s'appliquant. Le département ne garantit pas que le
fonctionnement de l'équipement satisfera l'utilisateur.
Avant d'installer cet équipement, les utilisateurs devront tout d'abord s'assurer que sa
connexion au réseau de la compagnie locale de télécommunications est autorisée.
L'équipement devra également être installé en utilisant une méthode de connexion agréée.
Le client doit être conscient du fait que le respect des conditions susmentionnées ne le
prémunit pas contre d'éventuels problèmes de service dans certaines situations. Toute
réparation ou altération effectuée/causée par l'utilisateur à cet équipement ou toute panne
de l'équipement pourra motiver une demande de déconnexion de l'équipement par
l'utilisateur de la part de la compagnie de télécommunications.
Pour leur propre sécurité, les utilisateurs devront s'assurer que les branchements à terre de
l'installation électrique, les lignes de téléphones et les canalisations d'eau métalliques
internes, si elles existent, sont connectés ensemble. Cette précaution est particulièrement
importante en milieu rural.

ATTENTION : les utilisateurs ne devront pas essayer de réaliser
ces connexions par eux-mêmes, ils devront contacter l'autorité
responsable de l'inspection électrique ou un électricien, comme il
se doit.

L'indice d'équivalence de la sonnerie (IES) assigné à chaque dispositif du terminal

pertinent donne une indication du nombre maximal de terminaux pouvant être connectés à
une interface de téléphone. Les connexions de sortie sur une interface pourront être
composées de toute combinaison de dispositifs à condition que la somme totale d'IES de
tous les appareils ne dépasse pas 5.
L'IES est utile pour déterminer la quantité d'appareils pouvant être connectés à la ligne de
téléphone. Si un nombre excessif d'IES est connecté sur une ligne de téléphone les
appareils pourraient ne pas sonner lors d'un appel entrant. Dans la plupart des zones, mais
pas dans toutes, la somme des IES de tous les appareils pouvant être connectés sur une

12 COLLABORATE Room: Installation and Setup Guide

ligne, est déterminée en fonction de l'IES total, veuillez vous adresser à la compagnie
téléphonique locale.

Australia

Safety / Low Voltage: AS/NZS CISPR 22:2004
Telecom (ISDN Point only): TBR-3

Japan

EMC: VCCI V-3
Telecom (ISDN Point only): Jate

RoHS & WEEE Declaration and Certification

These systems have been verified to comply with the EU RoHS & WEEE Directives
throughout the design, development and supply chain definition.
EU Directive on the Restriction of the use of certain Hazardous Substances in electrical and
electronic equipment (RoHS – 2002/95/EC) of 27 January 2003, and Directive of the
European Parliament and of the Council of 27 January 2003 on Waste Electrical and
Electronic Equipment (WEEE – 2002/96/CE).

This document is informational only and reflects laboratory performance. Your product may
perform differently, depending on components and peripherals you connect. Accordingly,
the customer should not rely upon this information in making decisions about electrical
tolerances or otherwise. No warranty as to accuracy or completeness is expressed or
implied. The information in this document may change without notice.

Environmental Data – Product's Materials Information Restricted Substances ClearOne's
products does NOT contain any of the following substances (in concentrations exceeding
legal threshold limits):



Asbestos



colorants in components that come into direct contact with human skin



Cadmium and its compounds (except for use in applications exempted by the EU RoHS
Directive)



Class I and Class II CFCs (chlorofluorocarbons) and HCFCs (hydro fluorocarbons)



Chloroparaffins, short chained (10-13 carbon chain)



Chromium VI and its compounds (except for use in applications exempted by the EU
RoHS Directive)



Halogenated dioxins or furans (i.e. polychlorinated dibenzodioxines, polychlorinated
dibenzofurans)



Lead and its compounds (except for use in applications exempted by the EU RoHS
Directive)

COLLABORATE Room: Installation and Setup Guide 13



Mercury (except for use in applications exempted by the EU RoHS Directive)



Nickel and its compounds in components that are likely to result in prolonged skin
exposure



PCBs (polychlorobiphenyls) or PCTs (polychloroterphenyls)



PBBs (polybromobiphenyls) or PBDEs (polybrominated diphenylethers)



PVC (polyvinyl chloride) in plastic parts greater than 25 grams



Polychlorinated naphthalenes (PCNs)



Tributyl tin (TBT) and triphenyl tin (TPT) compounds

Additional Materials Information



The cables may use PVC as an insulating material to ensure product safety



The case material is sheet metal



Product may contain post-industrial recycled content (plastics, metal, glass)

No CFCs (chlorofluorocarbons), HCFCs (hydrofluorocarbons) or other ozone depleting
substances are used in packaging material. Chromium, lead, mercury, or cadmium are not
intentionally added to packaging materials and are not present in a cumulative
concentration greater than 100 ppm as incidental impurities. No halogenated plastics or
polymers are used for packaging material. The System fully complies with the EU Directive
94/62/EEC.

The product has been tested in a typical configuration.

Technical file held by ClearOne
For a copy of the Original Signed Declaration (in full conformance with EN45014), please
contact ClearOne's Tech Support.

Certificate For China Compulsory Product Certification

The standards and technical requirement for the product: gb9254-1998

This is to certify that the above mentioned products have qualified for the requirements of
implementation rules for compulsory certification

14 COLLABORATE Room: Installation and Setup Guide

Table of Contents

Chapter 1: Introduction.................................................................................17

In this Chapter ..................................................................................................................................17

COLLABORATE Room Overview .....................................................................................................17

COLLABORATE Room Model Configurations .................................................................................17

COLLABORATE Room Basic ........................................................................................................17

Chapter 2: Unpacking and Connecting the System ....................................19

In this Chapter ..................................................................................................................................19

Unpacking ........................................................................................................................................19

Positioning........................................................................................................................................19

Connecting (FHD example)..............................................................................................................20

Chapter 3: Remote Control...........................................................................21

In this Chapter ..................................................................................................................................21

Using the Remote Control................................................................................................................21

Alphanumeric Keypad...................................................................................................................22

Command Buttons ........................................................................................................................22

Navigation Joystick and Additional Buttons..................................................................................23

Chapter 4: System Configuration .................................................................25

In this Chapter ..................................................................................................................................25

Starting the System..........................................................................................................................25

Monitor Configurations.....................................................................................................................25

Display Settings................................................................................................................................26

Network ............................................................................................................................................27

System Settings (IP)......................................................................................................................27

H.323 Settings...............................................................................................................................28

SIP Protocol Settings ....................................................................................................................30

ISDN Settings ................................................................................................................................30

ISDN Lines Configuration..........................................................................................................32

Camera.............................................................................................................................................33

Audio ................................................................................................................................................34

Chapter 5: Basic Operation ..........................................................................35

In this Chapter ..................................................................................................................................35

Initiating Calls ...................................................................................................................................35

Manual Dialer.................................................................................................................................35

Address Book................................................................................................................................36

Accepting a Call ...............................................................................................................................37

Chapter 6: Backup and Recovery.................................................................38

In this Chapter ..................................................................................................................................38

Performing System Backup .............................................................................................................38

Performing System Restore From Backup File................................................................................40

COLLABORATE Room: Installation and Setup Guide 15

Performing System Restore from FTP .............................................................................................42

Chapter 7: Specifications..............................................................................45

In this Chapter ..................................................................................................................................45

System Specification........................................................................................................................45

16 COLLABORATE Room: Installation and Setup Guide

Chapter 1:

Introduction

IN THIS CHAPTER

This chapter introduces the COLLABORATE Room videoconferencing system and includes
the following sections:



COLLABORATE Room Overview



COLLABORATE Room Model Configurations

COLLABORATE ROOM OVERVIEW

ClearOne’s COLLABORATE Room is a room system conferencing system that offers high­quality videoconferencing capabilities. Utilizing the newest H.264 video standard and clear,
crisp audio, the COLLABORATE Room brings users face-to-face with other people and
organizations.

The COLLABORATE Room incorporates advanced data conferencing capabilities, allowing
you to turn any videoconference into a fully interactive meeting easily. It can display
presentations or DVD videos on a large monitor, connect external laptop for data sharing
and open various document types stored on a USB key.

COLLABORATE ROOM MODEL CONFIGURATIONS

The COLLABORATE Room series includes the following model configurations:

COLLABORATE ROOM BASIC

This includes the basic system including the codec and all required accessories, including:



COLLABORATE Room Main Unit



Pan/Tilt/Zoom (PTZ) camera



Remote control



ClearOne Chat Mic



Power Supply



Cables

COLLABORATE Room: Installation and Setup Guide 17

Chapter 2:

Unpacking and Connecting the System

IN THIS CHAPTER

This chapter provides unpacking and connecting instructions and includes the following
sections:



Unpacking



Positioning



Connecting (FHD example)

UNPACKING

When you open the COLLABORATE Room system shipping package(s) for the first time,
please check that all items purchased according to the model (see specification above), are
included in accordance with the supplied product. If any of the items (according to your
customer order) are missing or damaged, contact your ClearOne distributor immediately.

POSITIONING

Please place the system on a steady surface, desirably ventilated and not exposed to
extreme temperatures. Make sure there is enough space for connecting the cables in the
back of the unit, and that the cables are not stretched between the main units the
accessories. Please do not place any items on top of the unit.

COLLABORATE Room: Installation and Setup Guide 19

CONNECTING (FHD EXAMPLE)

Connecting the cables and peripherals is done as shown in the following graphic which
visually presents all required connections.

In order to connect the COLLABORATE Room to its peripherals, follow the schematic
diagram (located on the back side of the guide) going from the left side.

You can identify each peripheral by matching the number on the cable with the numbered
picture on the front of the document.

The diagram contains the optional modules in addition to the basic option. If you did not
purchase any of the optional modules, please ignore those sections.

To connect the optional modules, after assembling the main unit, assemble the optional
module and finally connect it to the main unit.

NOTE: Connect the unit to the electricity only after all peripherals
are connected x>

20 COLLABORATE Room: Installation and Setup Guide

Chapter 3:

Remote Control

IN THIS CHAPTER

This chapter describes the remote control's features and includes the following section:



Using the Remote Control

USING THE REMOTE CONTROL

You can navigate the COLLABORATE Room on-screen graphic user interface (GUI) using
the infrared remote control, bundled with the unit.

Pressing any button on the remote control activates the on-screen GUI, which appears on
top of the camera/videoconference picture.

The remote control includes the following button types:



Alphanumeric Keypad



Command Buttons



Navigation Joystick and Additional Buttons.

COLLABORATE Room: Installation and Setup Guide 21

ALPHANUMERIC KEYPAD

The remote control includes an alphanumeric keypad with buttons from 0 to 9, as well as '.',
',', '*', '#', '^', '@', '$', ':', '=', '-', '_' and Clear ( Backspace) characters accessed by repeat
button presses.

In different windows, you can toggle between numbers and letters, depending on the field.
Some fields accept numbers only.



Switch between letters and numbers by pressing a few times on the corresponding key



Use Volume Up/Down buttons when you need to activate/deactivate CAPS lock



When DTMF dialing is requested, use the numeric keypad.

COMMAND BUTTONS

The following command buttons are available on the remote control:

Button Image Button Name Command

Status Display the current call status

Data Initiate data sharing

Phone Book Open the phone book

Help Show the on-screen online help

Far End Control the position (PTZ) of the camera at the

Camera Control Configure the camera position settings

Preset: Recall Recall a camera PTZ preset position

Preset: Set Set a camera PTZ preset position

Picture-In-Picture (PIP) Toggle the PIP position (5 positions + Side-by-

Speed Dial Display the speed dial options

Call Log Display the current call log

Mute Mic Mute the local microphone

Display Toggle the local and remote displays

near/far end

Side)

22 COLLABORATE Room: Installation and Setup Guide

Button Image Button Name Command

Settings Open the settings menu

Mute Video Temporarily disable the local video camera

Mute Speaker Mute the speaker

and its transmission

NAVIGATION JOYSTICK AND ADDITIONAL BUTTONS

Using the joystick of the OK button, you can navigate the GUI menus/options in four
directional movements: Up , Down , Left , and Right .

In addition to the joystick, the following buttons are available around it:



Back – Returns to the previous step/window without saving changes



Menu/OK – Selects/activates a highlighted GUI item/function (highlighted in green on
the screen)



Volume Up/Down – Increases/decreases the volume or switches between lower and
upper case



Zoom In/Out – Zooms in or out with the camera



Make Call – Start a new call



End Call – End the current call or close the GUI.

NOTE: The red End Call button can also be used for turning off the
unit. Press and hold the button until the shutdown confirmation
prompt appears. Selecting “Yes” immediately shuts down the
system.

COLLABORATE Room: Installation and Setup Guide 23

Chapter 4:

System Configuration

IN THIS CHAPTER

This chapter describes how to configure the system and includes the following sections:



Starting the System



Monitor Configurations



Display Settings



Network

STARTING THE SYSTEM

Once the system is properly wired, connect it to the electricity and power it up using the
power switch on the front. When system fully loads, you will see the view from the camera
on the entire screen.

The COLLABORATE Room system is capable of using one or two displays. According to
the devices you physically connected to the system, configure the appropriate settings
using the system configuration options.

In order to access the configuration screens, press the Menu/OK button on the remote
control. A menu will open with various options. Select the Settings option and press the

Menu/OK button on the remote control, or use the right arrow to expand this menu option.

MONITOR CONFIGURATIONS

The COLLABORATE Room display configuration ranges from single monitor to dual
monitor. When using a single monitor, both the local video and remote video are displayed
on the same display, whereas when using dual displays, each video stream is displayed on
a separate display.

The video output signal can be connected using various output interfaces:



DVI – The DVI (Digital Visual Interface) interface is common in LCD and flat panel
displays.



HDMI – The HDMI (High-Definition Multimedia Interface) interface is common in LCD
and flat panel.

When connecting your system, please follow the attached quick reference sheet for using
the connector which is appropriate to your system. Once the displays are connected, use
the system user interface to configure the display settings.

COLLABORATE Room: Installation and Setup Guide 25

DISPLAY SETTINGS

To configure the display settings:

1. Select Settings>Display from the main menu.

2. In the Display Settings window, set the following options:

 Display Mode –

 Single Mode – Both videoconference parties are displayed on a single screen.
 Dual Mode – Conferences are displayed on two screens. This option is

available only when two screens are connected.

 Device and Resolution – Select an option from the lists.
 Keep Aspect Ratio – Select this option to keep the original aspect ratio on screens

that have different aspect ratio.

 Display Remote on Main – When using multiple monitors, display the remote side

on the main display. Uncheck to display the remote on the secondary monitor

3. Click OK.

26 COLLABORATE Room: Installation and Setup Guide

NETWORK

The COLLABORATE Room system is a communication device that relies on various
networks and protocols. Before you can use the system, you must configure its network
settings according to the network you intend to use.

SYSTEM SETTINGS (IP)

1. Select Settings>Network>System from the program main menu.

2. In the System Settings window, set the following options and parameters:

 Obtain Address from DHCP Server – Select the checkbox to obtain an IP address

from a DHCP server.

 IP Address – Set the IP address for this system. If using a DHCP server, the

address obtained from the DHCP server is displayed.

 Subnet Mask – Set the subnet mask number for your network. If using a DHCP

server, the address obtained from the DHCP server is displayed.

 Default Gateway – Set the IP address of the default gateway router. If using a

DHCP server, the address obtained from the DHCP server is displayed.

 Obtain DNS Automatically – Use the DHCP server to decide your DNS server

address. If you do not select Obtain address from DHCP server, fill in the following
fields:

 DNS Server – Set the IP address of the DNS server. If using a DHCP server, the

address obtained from the DHCP server is displayed.

 Additional DNS Server – Alternative DNS server, to be used in case the first DNS

server defined can’t supply the needed services.

COLLABORATE Room: Installation and Setup Guide 27

 DNS Suffix – Set the DNS domain suffix to be used by this system.
 System Name – Set the system DNS name used to identify the system when using

DNS dialing.

 Ethernet Speed – Displays the network interface speed.

NOTE: Modify these settings only if they are required in your
network.

3. Select Apply.

H.323 SETTINGS

H 323 is a TCP/IP video conference protocol used by videoconference endpoints.

To configure the H.323 settings:

1. Select Settings>Network>IP>H.323 from the main menu.

2. In the H.323 settings screen, select the management server to which the

COLLABORATE Room system is registered, if not working in standalone mode.

 None – Keep this option selected (selected by default) if you do not want to use a

COLLABORATE Central server or a gatekeeper.

 COLLABORATE Central – Select this option if you want COLLABORATE Room to

communicate/interact with a COLLABORATE Central server and utilize its advanced
features. If selected, enter the required details in the following fields:

 Server Address – Enter the IP address of the COLLABORATE Central server.
 User Name – Enter the user name used to log into the COLLABORATE Central

server.

28 COLLABORATE Room: Installation and Setup Guide

 User Number – Enter your user number used for identification on the

COLLABORATE Central server. If not entered, the COLLABORATE Central
server will automatically generate a number.

 Password – Enter the password used to log into the COLLABORATE Central

server.

 Gatekeeper – Select this option if you want COLLABORATE Room to

communicate/interact with a gatekeeper server. If selected, enter the required
details in the following fields:

 Server Address – Enter the IP address of the gatekeeper server.
 User Name – Enter the user name used to log into the gatekeeper server.
 User Number – Enter the user number used for identification on the gatekeeper

server.

 Password – Disabled when working with a gatekeeper because gatekeeper

authentication is currently not supported.

 Connection Mode – Select the protocol you want to use to connect your call.

 H.323 - This selection should be selected manually for LAN network

connections only when the connection type is known.

 H.460 - This selection should be selected manually for network connections

over Firewall/NAT only when the connection type is known.

 Tunneling (not available when working with a gatekeeper) - This selection

should be selected manually for ClearOne Proprietary Tunneling. The default
tunneling port is configured by the System Administrator (see NetPoint/
COLLABORATE Central Administration Configuration Manager).

NOTE: Changing this setting causes COLLABORATE Room to
reload.

 RTP Ports – In the two boxes, set the RTP range:

 From – Enter the minimum RTP value.
 To – Enter the maximum RTP value.

3. Select Apply.

COLLABORATE Room: Installation and Setup Guide 29

SIP PROTOCOL SETTINGS

SIP is a common communication signaling protocol for VoIP.

To configure SIP settings:

1. Select Settings>Network>IP>SIP. The SIP Settings window appears.

2. In the SIP Settings window, set the following options and parameters:

 Use Proxy – Use a proxy server or as stand alone.

 User Name – The user name as configured in the proxy server (proxy mode).
 User Password – The user password as configured in the proxy server (proxy

mode).

 Proxy Address – Proxy server IP

 Local Port – The SIP port on your computer (the standard is 5060).
 Transport Protocol – Select the desired protocol (TCP or UDP).

3. Select Apply.

ISDN SETTINGS

ISDN (Integrated Services Digital Network) is a protocol that provides video conferencing
capabilities over telephone lines. It must be configured if the system is connected through
the ISDN infrastructure.

NOTE: The ISDN functionality is available only if you purchased a
license code and the required peripherals for it . You can skip this
section if you did not purchase the ISDN option and if you do not
use ISDN lines.

COLLABORATE Room can register to an ISDN point via the IP LAN.

The ISDN wizard enables connection to ISDN based networks, using up to 4 ISDN BRI
lines, reaching connection bandwidth of up to 512 kbps.

30 COLLABORATE Room: Installation and Setup Guide

To configure ISDN settings:

1. Select Settings>Network>ISDN. The ISDN Settings configuration wizard appears.

NOTE: The ISDN configuration wizard includes two or three steps,
depending on the switch type used, which is country dependant.
The configuration wizard guides you through the steps depending
on your selection of device and switch types.

2. The ISDN Connection wizard screen includes the following properties:

 Enable ISDN – Select this option to enable or disable ISDN functionality. Once

selected, the ISDN adapter detection may take up to a minute.



Available Adapters – Displays the list of ISDN adapters available for this system.
Click on Discover to populate the Available Adapters list, and select the desired
adapter from the list. After you select an adapter, the Adapter Information, IP
address and MAC address of the adapter are displayed.

 Discover adapters – Select this button to scan for available ISDN adapters.
 Adapter Information:

 IP Address – IP address of the ISDN adapter.
 MAC Address – MAC Address of the ISDN adapter.

 Line Indicators – Displays the line status after connecting:

 Line 1: ISDN line status for line number 1
 Line 2: ISDN line status for line number 2
 Line 3: ISDN line status for line number 3
 Line 4: ISDN line status for line number 4

3. Select Next to continue to the ISDN Lines Configuration step (see ISDN Lines

Configuration).

COLLABORATE Room: Installation and Setup Guide 31

ISDN LINES CONFIGURATION

The ISDN Lines Configuration window enables you to set the phone numbers of up to 4
lines.

To define the ISDN phone numbers:

1. Enter the appropriate number for each field, without the area or country code.

NOTE: Depending on the switch type you selected, an additional
step may be required. If you are not sure what numbers to enter,
consult your system administrator.

2. Select Finish to save the ISDN lines configuration and complete the configuration

wizard.

32 COLLABORATE Room: Installation and Setup Guide

CAMERA

The camera attached to the system can be configured for various parameters, select
Settings>Camera from the main menu to access the camera configuration screen

1. In the Camera Settings window, select the correct options from the Camera, Input

Device, and Capability drop-down lists.

NOTE: COLLABORATE Room supports PTZ cameras only.

2. Optional: set the percentage (%) of Color, Contrast, Brightness, and Hue. You can

leave the default settings of these parameters unchanged.

3. Specify the Communication Port you are using (default is COM 1).

NOTE: If you connect the camera to a port other than the last one
used (or in a new installation, other than COM 1), you will need to
restart the system.

4. Select the correct option from the Camera Model and Analog Video Format drop-

down lists.

5. Select the Allow Far End Camera Control (FECC) check box to enable the remote

side to control your camera (unavailable when working with SIP).

6. Select Apply to apply the changes without leaving this window, or select OK (in the

GUI) to save the changes and close the Camera Settings window.

7. For FHD model only: Select the camera resolution according to your camera settings

(1080p/30 or 720p/60)

COLLABORATE Room: Installation and Setup Guide 33

AUDIO

To configure the audio settings:

1. Select Settings>Audio from the main menu.

2. In the Audio Settings window, set the following properties of the selected audio input.

USB devices can be used if the system supports external USB hardware.

 Playback Device – Select a playback device from the list.
 Recording Device – Select a recording device from the list.
 Audio Input – ClearOne Chat Mic connected to USB Port.
 Microphone Level – Adjust the microphone sensitivity level in percentage (%).
 Microphone Boost – For future use.
 Acoustic Echo Cancellation – Select the check box to prevent echo when the

microphone and speaker are in the same room. Disable this feature when it is
supported by an external device.

 Lip Synchronization – If the voice you hear is not synchronized with the lip

movement in the video display, move the slider as follows:

 Towards Delay Video if voice is heard after the lip movement
 Towards Delay Audio if you see the appropriate lip movement after you hear

the voice.

 Auto Noise Suppression – Suppress unwanted background noises. Disable

this feature when it is supported by an external device.

3. Select Apply.

34 COLLABORATE Room: Installation and Setup Guide

Chapter 5:

Basic Operation

IN THIS CHAPTER

This chapter describes the basic operations of the system and includes the following
sections:



Initiating Calls



Accepting a Call

INITIATING CALLS

Calls can be initiated in several ways:



From the Manual Dialer



From the Address book



From the Online Dialer



From the Speed Dial

MANUAL DIALER

To initiate calls using the manual dialer:

1. Press the Menu button on the remote control. A list of actions available is displayed.

2. Select from the system menu

3. Enter the address of the remote party:

 LAN – IP address, Alias, E.164 number or DNS address.
 ISDN – Phone Number.

4. Select the type of call:

 H.323 or SIP – To initiate a call through the connected local network (LAN).
 ISDN - To initiate a call through ISDN line(s). The ISDN system must be configured

beforehand via the ISDN Settings pages.

5. Select the maximum bandwidth for the call. If you are not sure, use the default on the

screen.

6. Press Dial to initiate the call.

COLLABORATE Room: Installation and Setup Guide 35

ADDRESS BOOK

The address book enables calling via the following methods:



Personal address book – Addresses stored on the local system



Call Log – Select from previously carried out calls.



Directory – Select a contact from the online directory



Speed Dial – Use predefined short cut numbers for quick dialing.

To initiate calls using the address book:

7. Press the Menu button on the remote control. A list of actions available is displayed.

8. Select

from the system menu.

9. Select the Address book option by moving to the right with the arrow keys on the

remote control. The address book form is displayed.

10. Scroll using the up and down arrow keys. You can also use the numeric keypad to

enter a letter (the letters are printed on the remote control) to jump to a specific name.
To move to different categories, move to the left and then scroll between the 4 options
(personal, call log, directory and speed dial).

11. Press the Ok button on the remote control. The address of the contact is copied to the

number field.

12. Press the Dial button on the remote control or select the Call option on the screen

when you are ready to initiate the call.

36 COLLABORATE Room: Installation and Setup Guide

When the call is initiated, indicators will appear on the screen.

After the destination accepts the call, the video of the remote party appears and the
audio of the remote site is now heard from your speakers.

ACCEPTING A CALL

When an incoming call is initiated, a message is displayed on the screen. The details of the
calling party is displayed on the screen (if available), you can accept or reject the call using
the buttons on the remote control or on the message on the screen.

The ability to auto answer all calls is available via the Calls Settings screen.

COLLABORATE Room: Installation and Setup Guide 37

Chapter 6: Backup and Recovery

IN THIS CHAPTER

This chapter describes the system's backup and recovery mechanism and includes the
following sections:



Performing System Backup



Performing System Restore From Backup File



Performing System Restore from FTP

PERFORMING SYSTEM BACKUP

The Backup option, using an attached keyboard and mouse, takes a snapshot of the
current COLLABORATE Room configuration. It is recommended to take backup snapshots
every time a configuration change is made.

1. Open your Internet Explorer browser.

2. In the browser’s address bar, type the direct IP Address of the COLLABORATE Room

unit. The COLLABORATE Room web login page appears. For example:

http://172.100.100.25

After logging in, click System>System Restore. The System Restore box appears.

NOTE: For the current release the Backup and Restore functions
are accessed by the same screen.

3. Click OK, or wait and the system will automatically reboot.

4. The system will reboot and a Backup/Restore screen will appear

38 COLLABORATE Room: Installation and Setup Guide

5. Select the Backup option (F1). The Backup screen will appear.

6. Enter the Backup name and click on the Create (F4) button to create the backup file of

the configuration.

7. Once it is done, press the Exit (F12) button and reboot the system. Shutdown the

system by pressing few seconds on the power button; then press the power button
again in order to turn on the system.

COLLABORATE Room: Installation and Setup Guide 39

PERFORMING SYSTEM RESTORE FROM BACKUP FILE

Whenever necessary, you can discard all manually entered configuration settings and
restore the settings to a saved backup of an earlier configuration.

NOTE: before restoring the system, you must save the system
License Key. This is accessed by using the menu:

Configuration>Option>License

Reset the COLLABORATE Room unit to a backup snapshot file using an IE browser:

1. Open your Internet Explorer browser.

2. In the browser’s address bar, type the direct IP Address of the COLLABORATE Room

unit. The COLLABORATE Room web login page appears. For example:
http://172.100.100.25

3. After logging in, click System>System Restore. The System Restore box appears.

NOTE: For the current release the Backup and Restore functions
are accessed by the same screen.

4. Click OK.

NOTE: All information on the system including user information,
address book entries, IP settings, ISDN settings and all other user
defined information will be deleted.

NOTE: After restoring the system to its factory defaults, it may be
necessary to perform a system upgrade.

5. The system will reboot and Backup/Restore menu will appear.

40 COLLABORATE Room: Installation and Setup Guide

6. Select the Restore (F2) button. The Restore screen will appear.

7. Select the backup configuration file you want to restore, and press on Restore (F5)

button.

8. Once the restore process is completed, press OK and shutdown the system by

pressing a few seconds on the power button; then press the power button again in
order to turn on the system.

9. Copy the stored License Key to the system (Configuration>Option>License)

COLLABORATE Room: Installation and Setup Guide 41

PERFORMING SYSTEM RESTORE FROM FTP

Whenever necessary, you can discard all manually entered configuration settings and
restore using settings delivered via FTP.

NOTE: before restoring the system to its factory defaults, you must
save system License Key. This is accessed by using the menu:

Configuration>Option>License

To reset the COLLABORATE Room unit, using an attached keyboard and mouse, to its
factory defaults:

1. Open your Internet Explorer browser.

2. In the browser’s address bar, type the direct IP Address of the COLLABORATE Room

unit. The COLLABORATE Room web login page appears. For example:

http://172.100.100.25

After logging in, click System>System Restore. The System Restore box appears.

3. Click OK.

NOTE: All information on the system including user information,
address book entries, IP and ISDN settings and all other user
defined information will be deleted.

NOTE: After restoring the system to its factory defaults, it maybe be
necessary to perform a system upgrade.

4. The system will reboot and Backup/Restore menu will appear.

42 COLLABORATE Room: Installation and Setup Guide

5. Select the FTP Updates (F3) button. The FTP Updates screen will appear.

6. Enter the FTP server details including FTP Address, User Name and Password, and

click the Apply (F9) button.

7. Press the Available Updates (F8) button to refresh the backup file list.

8. Select the file from the listing, and then click on the Download (F6) button.

9. Once the download is completed, press on the Back (F11) button.

10. Select the Restore (F2) button and follow the restore steps listed above.

COLLABORATE Room: Installation and Setup Guide 43

Chapter 7:

Specifications

IN THIS CHAPTER

This chapter provides the system specification and includes the following section:



System Specification

SYSTEM SPECIFICATION

Video Specifications

Transmission Speed

Video Standards H.261, H.263, H.263+/++, H.264

Live Video Resolution

 H.323 / SIP: 96 Kbps - 6Mbps ( SD up to 4Mbps)
 ISDN 64 Kbps -512 Kbps (4xBRI)*

*not supported in current version

 QCIF (176 x 144 pixels)
 QVGA (320 x 240 pixels)
 CIF (352 x 288 pixels)

Video Frame Rate

Video Inputs

 SIF (352 x 240 pixels)
 VGA (640 x 480 pixels)
 4CIF (704 × 576)
 4SIF (704 x 480)
 720p (1280 x 720 pixels) Rx/Tx HD, Rx SD
 1080p (1920 x 1080 pixels) - Rx SD/HD, Tx/Rx PHD and

Tx/Rx FHD

 720/60 - 1080/30 (Rx SD/HD, Tx/Rx PHD and Tx/Rx

FHD)

 1080/60 (Rx SD/HD/FHD, Tx/Rx PHD)

 Up to 10 fps: 96 Kbps
 Up to 20 fps: 128 to192 Kbps
 Up to 30 fps: 256 Kbps and higher

 SD: Composite and S-Video
 HD: HDMI or HD-SDI
 FHD: HDMI
 PHD: DVI

Video Outputs HDMI, Digital Video Interface (DVI)

HD Simulcast Integrated Broadcast Viewer

COLLABORATE Room: Installation and Setup Guide 45

Audio Specifications

Audio Features

Audio Standards

Data Specifications

HD DualStream

 Full duplex echo cancellation
 Automatic noise suppression (ANS)
 Automatic gain control (AGC)

 20 KHz: AAC-LD
 7 KHz: G.722, G.722.1
 3.4 KHz: G.711, G.723.1, G.728,G.729
 AMR (3G)

 Data Sharing Methods
 Laptop plug in (via Tabletop Pod)
 USB storage key
 Documents: PPT, PPS
 Video clips (AVI, MPEG, WMV, etc.)
 Graphic files (BMP, GIF, TIF, etc.)

 Sharing of file, or the VGA input
 H.239 support
 Tandberg DuoVideo support
 Sending and receiving capability
 1 live video source + 1 data source
 Resolutions supported: XGA, SVGA, VGA, CIF, QVGA, QCIF,

4CIF

46 COLLABORATE Room: Installation and Setup Guide

Networking Specifications

Standards Supported

H.323 QoS Features

 ITU-T: H.323 v4.2 Annex Q (FECC)
 SIP Protocol: RFC 3261
 ISDN: H.320*, H.221, H.242, H.230

* This option will be supported in a future version of
COLLABORATE Room.

 DiffServ
 IP Precedence
 Firewall port sync
 NAT IP mask
 Port pinholing
 Adaptive Bandwidth Adjustment
 Packet loss recovery (FEC)
 Packet ordering
 Packet duplication control
 Jitter correction
 Lip sync correction

Peripheral Specifications

Monitors Configuration

Pan-Tilt-Zoom Camera Unit

 Overhead prediction
 Max packet size adjustment

 Single DVI or HDMI
 Dual: DVI + HDMI

 PHD: 14x Zoom
 FHD: 14x Zoom
 HD: 10 or 14x Zoom
 SD: 18x Zoom

COLLABORATE Room: Installation and Setup Guide 47

Features Specifications

Dialing Modes

Security

Directory Services

 Manual
 Speed dial
 Personal address book
 Online directory
 Broadcast viewer

 Encryption using H.235 (AES)
 Search and filter Packet ordering
 Packet duplication
 AES is NIST validation
 Firewall traversal using NetPoint H.460 protocol and

ClearOne Tunneling proprietary protocol

 Network address translation
 Supports restricted access to users via admin

 1000+ local number directory
 10,000+ global number directory
 H.350 support (COLLABORATE Central mode)
 LDAP online directory support

 OpenLDAP
 Microsoft ILS, SiteServer, Active Directory and

Exchange

 Search and filter queries

Environmental

Language Support English, French, German, Italian, Russian, Chinese, and Korean

 0 - 40°C temperature
 15 - 80% humidity
 Universal Power Supply:

 Input 100~240VAC@1.8A


Frequency 50/60 Hz

 PS Output / Appliance Input:

 12VDC@6.67A Max

48 COLLABORATE Room: Installation and Setup Guide