CleanSpace CleanSpace2 User Instructions

www.cleanspacetechnology.com

Important! Before use, the wearer must read and understand these

user instructions. Keep these user instructions for reference.

CleanSpace2

Powered Respirator

USA – English

TC-21C-1065

www.cleanspacetechnology.com

USER

INSTRUCTIONS

2

1. Contents

1. Contents ............................................................................................................................................................... 2

2. Forward ................................................................................................................................................................ 2

3. System Description .............................................................................................................................................. 3

4. List of Warnings within these User Instructions................................................................................................... 3

5. NIOSH – Approval, Cautions and Limitations ..................................................................................................... 4

6. S - Special or Critical User Instructions ............................................................................................................... 5

7. Limitations of Use ................................................................................................................................................ 5

8. Respirator Program Management ....................................................................................................................... 6

9. System Components............................................................................................................................................ 7

10. Controls and Indicators ........................................................................................................................................ 9

11. Mask Fitting ........................................................................................................................................................ 10

12. Using CleanSpace2 ........................................................................................................................................... 11

13. Entering and Exiting the Contaminated Area .................................................................................................... 19

14. Working in Noisy Environments ......................................................................................................................... 20

15. Fitting & Changing the Filter .............................................................................................................................. 21

16. Battery Information............................................................................................................................................. 25

17. Cleaning ............................................................................................................................................................. 27

18. Periodic Maintenance & Checking ..................................................................................................................... 28

19. Specifications ..................................................................................................................................................... 29

20. Product and Accessory information ................................................................................................................... 30

21. Product Warranty ............................................................................................................................................... 31

Read these instructions in conjunction with the appropriate CleanSpace™ filters and accessories instructions.

WARNING

This product is part of a system that helps protect against certain airborne contaminants. Misuse

may result in sickness or death. For proper use, see your Occupational Health Specialist, these

user instructions or contact PAFtec Customer Service on 1 888 804 0038

2. Forward

Read all instructions and warnings before using this device. Keep these user instructions for reference. If you have
questions regarding this system contact PAFtec Customer Service on 1 888 804 0038 or e-mail
[e-mail]

3

3. System Description

The PAFtec CleanSpace2 is a complete NIOSH approved respiratory system. When used in accordance with its
NIOSH approval, the respirator helps to provide respiratory protection against particulates. CleanSpace2 does not
provide protection against vapours or gasses and is not an intrinsically safe system. See the NIOSH Approval
Section of these user instructions for additional information on approvals.

The components of the CleanSpace2 system are shown in Section 9. The blower draws ambient air through the high
efficiency filter (and filter adaptor if used) and supplies filtered air to the wearer via the mask. CleanSpace2 is a
breath responsive respirator which means that it blows harder during inhalation and more softly during exhalation.
The device continuously adjusts fan speed to maintain positive pressure in the mask. Should the filter become

blocked, an audible alarm will sound and the “Filter” light on the keypad will be illuminated. If the battery voltage falls

below the minimum required to sustain the designed flow rate, an audible alarm will sound.

WARNING

Properly selected, used and maintained respirators help to protect against certain airborne
contaminants. It is essential to follow all instructions and government regulations on the use of this
product, including wearing the complete respirator system during all times of exposure, in order for

the product to help protect the wearer. Misuse of respirators may result in overexposure to

contaminants and lead to sickness or death. For proper use, see your Occupational Health

Specialist, these user instructions or contact PAFtec Customer Service on 1 888 804 0038

4. List of Warnings within these User Instructions

WARNING

This product is part of a system that helps protect against certain airborne contaminants. Misuse may result in sickness or death. For proper use, see your

Occupational Health Specialist, these user instructions or contact PAFtec Customer Service on 1 888 804 0038

WARNING

Properly selected, used and maintained respirators help to protect against certain airborne contaminants by reducing concentrations in the wearer’s breathing

zone. It is essential to follow all instructions and government regulations on the use of this product, including wearing the complete respirator system during all

times of exposure, in order for the product to help protect the wearer. Misuse of respirators may result in overexposure to contaminants and lead to sickness

or death. For proper use, see your Occupational Health Specialist, these user instructions or contact PAFtec Customer Service on 1 888 804 0038

No PAPR can fully protect you if you are not clean shaven. CleanSpace2 is not suitable for users with facial hair.

IF A SATISFACTORY FIT FACTOR CANNOT BE ACHIEVED WITH ANY OF THE MASKS, CLEANSPACE2 MUST NOT BE USED

DO NOT USE COMPRESSED AIR OR A BRUSH TO CLEAN THE FILTER!

HEPA FILTERS ARE VERY EASILY DAMAGED BY THE USE OF COMPRESSED AIR OR BY BRUSHING.

Misuse of CleanSpace2 by cleaning the filter may result in overexposure to contaminants and lead to sickness or death.

IF A SATISFACTORY FIT CANNOT BE ACHIEVED, DO NOT ENTER THE CONTAMINATED ZONE

Be sure to remove the Seal Check Cap before entering the contaminated area. The Cap blocks the exhalation valve, making it more difficult for your

exhaled air to be expelled from the mask. Failure to remove the cap will lead to build-up of Carbon Dioxide in the mask, and may result in headache or

dizziness.

Never leave the Cap in place for more than 2 minutes!

DO NOT REMOVE THE RESPIRATOR UNTIL YOU HAVE

VACATED THE CONTAMINATED AREA unless you have pressing health reasons to do so (for instance you are experiencing dizziness and believe

removing the respirator while you leave the contaminated area may help)

IT IS ESSENTIAL THAT THE CORRECT FILTER TYPE IS SELECTED

FOR THE CHOSEN APPLICATION.

If the blocked filter alarm is triggered (2 beeps, repeated every second, red LED flashes), leave the contaminated area immediately and replace the filter.

Operating the respirator after the blocked filter alarm has sounded can cause the flow to fall below the manufacturer’s minimum designed flow, which

may result in overexposure to contaminants and lead to sickness or death.

DO NOT USE COMPRESSED AIR OR ANY OTHER MECHANICAL METHOD TO CLEAN THE FILTER!

HEPA FILTERS ARE VERY EASILY DAMAGED BY THE USE OF COMPRESSED AIR OR BY BRUSHING.

Misuse of CleanSpace2 by cleaning the filter may result in overexposure to contaminants and lead to sickness or death.

Use only NIOSH-approved CleanSpace™ filters with the CleanSpace2™ respirator. If used with other filters CleanSpace2 is not NIOSH approved. Use of

other filters may result in overexposure to contaminants and lead to sickness or death.

4

CleanSpace2 is not intrinsically safe. Do not use in flammable or explosive atmospheres. Doing so may result in injury or death.

Always correctly use and maintain the internal lithium ion battery packs. Failure to do so may result in fire or explosion or could adversely affect

respirator performance and result in injury, sickness or death.

- Do not charge the on-board battery with unapproved chargers, in enclosed cabinets without ventilation, near flammable liquids or gasses, or near

sources of high heat

- Do not immerse the device in water

- Do not use, charge or store the device outside the recommended temperature limits

If the battery alarm sounds (3 beeps, repeated every second), leave the contaminated area immediately and re-charge the battery.

Operating the respirator after the low battery alarm has sounded can cause the flow to fall below the manufacturer’s minimum designed flow, which

may result in overexposure to contaminants and lead to sickness or death.

The Flow Test is not a battery charge test. Three LEDs means that, as of the moment it is tested, the unit can deliver high flow. It does not mean the
battery is full. You must check the battery condition separately. See Section 16.

IN THE EXTREMELY RARE CIRCUMSTANCE THAT THE BATTERY

IS DAMAGED AND ELECTROLYTE COMES IN CONTACT WITH EYES,

FLUSH WITH WATER IMMEDIATELY AND SEEK URGENT MEDICAL ATTENTION

WARNING: NEVER DRY THE MASK OR EXHALATION VALVE WITH A CLOTH THAT MAY LEAVE BEHIND LINT.

Lint contamination of the exhalation valve may cause it to leak, resulting in overexposure to contaminants and lead to sickness or death.

WARNING: The blower contains a battery, sensitive electronics and a motor. NEVER immerse it in water or use anything wetter than a damp cloth to

clean it.

WARNING: NEVER CLEAN THE FILTER WITH COMPRESSED AIR OR A BRUSH. HEPA FILTERS ARE EASILY DAMAGED BY THE USE OF

COMPRESSED AIR OR BY BRUSHING.

Misuse of CleanSpace2 by cleaning the filter may result in overexposure to contaminants and lead to sickness or death.

You must recalibrate the internal pressure sensor any time that your CleanSpace2 is exposed to changes in temperature of more than 36°F (20°C).

WHEN FITTING A NEW FILTER THE BLOCKED FILTER ALARM SHALL BE TESTED BEFORE THE

RESPIRATOR IS PUT BACK INTO SERVICE. SEE “TESTING THE BLOCKED FILTER ALARM” AT THE

END OF THIS SECTION

5. NIOSH – Approval, Cautions and Limitations

NIOSH APPROVAL

CleanSpace2 is a NIOSH-approved respirator system. Refer to these User Instructions and to the NIOSH approval
label provided with each CleanSpace2 for a listing of components that can be used to form a NIOSH-approved
respirator.

NIOSH CAUTIONS AND LIMITATIONS

A - Not for use in atmospheres containing less than 19.5 percent oxygen.
B - Not for use in atmospheres immediately dangerous to life or health.
C - Do not exceed maximum use concentrations established by regulatory standards.
F - Do not use powered air-purifying respirators if airflow is less than four cfm (115 lpm) for tight fitting facepieces or

six cfm (170 lpm) for hoods and/or helmets.
I – Contains electrical parts that may cause an ignition in flammable or explosive atmospheres
J - Failure to properly use and maintain this product could result in injury or death.
L - Follow the manufacturer's User's Instructions for changing cartridges, canister and/or filters.
M - All approved respirators shall be selected, fitted, used, and maintained in accordance with MSHA, OSHA, and

other applicable regulations.
N - Never substitute, modify, add, or omit parts. Use only exact replacement parts in the configuration as specified

by the manufacturer
O - Refer to User's Instructions, and/or maintenance manuals for information on use and maintenance of these

respirators.
P - NIOSH does not evaluate respirators for use as surgical masks.
S - Special or critical User's Instructions and/or specific use limitations apply. Refer to User's Instructions before

donning.

5

6. S - Special or Critical User Instructions

This respirator contains a system for synchronising with your breathing and regulating mask pressure. This system
requires re-calibration whenever it experiences a change in temperature of more than 36°F (20°C). It is best
practice to also re-calibrate if the unit has been in storage, particularly if the storage temperature is not
known.

For the most accurate battery charge indication, the respirator must be plugged into its charger. To be sure it is fully
charged, plug in the charger and wait for all 3 LEDs to light solidly without flashing. If the 3rd LED is flashing
rapidly, the battery is 95% charged.

7. Limitations of Use

Use this Respirator strictly in accordance with all instructions in these user instructions. Never modify or alter this
product.



Do not remove the Respirator until you have left the contaminated area

,

unless you have pressing health reasons to do so (for instance you are experiencing dizziness and
believe removing the respirator while you leave the contaminated area may help).



Only suitable for use by clean-shaven personnel. Facial hair under the seal reduces protection and is not

permitted.



This Respirator DOES NOT PROTECT YOUR EYES. In conditions that may damage or irritate eyes, use

protective eyewear.



Only use your respirator with the parts and accessories listed on the Approval Label.



Do not use the respirator unless it is powered and running normally.



Do not use the respirator while it is being charged via the AC adaptor.



Do not use in airborne contaminant concentrations above those specified in your national regulations



Do not use for respiratory protection against unknown atmospheric contaminants or when concentrations

of contaminants are unknown or immediately dangerous to life or health (IDLH).



Do not use in oxygen deficient or oxygen enriched atmospheres. Do not use in flammable or explosive

environments.



Only for use by trained personnel.



Filters need to be changed regularly. The frequency of change depends on use and the concentration of

contaminants in the atmosphere.



Do not use for escape purposes. National regulations may impose specific limitations on the use of filters

depending on the filter class and the facemask used.

LEAVE THE CONTAMINATED AREA IMMEDIATELY IF:



Respirator warning lights and/or sounds activate for low battery or blocked filter



Any part of the respirator is damaged



Air flow into the mask decreases or stops



Breathing becomes difficult or increased resistance occurs



You feel dizzy or your airway is irritated



You can taste or smell contaminants

Your respirator is suitable for use in the following atmospheric conditions:



Temperature: 14°F to 113°F (-10°C to 45°C)



Relative humidity: 0 to 90% non-condensing

The respirator will stop functioning if its internal temperature rises above 140°F ( 60°C) or falls below 14°F (-10°C)
If the respirator has been used in an area that has caused it to become contaminated with a substance requiring

special decontamination procedures it should be placed in a suitable container and sealed until it can be
decontaminated.

6

Do not disassemble the respirator case. There are no user serviceable parts inside.
Failure to follow all instructions on the use of this product, and/or failure to use the respirator during times of

exposure, may lead to adverse effects on the wearer’s health and may render the warranty void.

WARNING

This product is part of a system that helps protect against certain airborne contaminants. Misuse

may result in sickness or death. For proper use, see your Occupational Health Specialist, these

user instructions or contact PAFtec Customer Service on 1 888 804 0038

8. Respirator Program Management

Occupational use of respirators must be in compliance with applicable health and safety standards. By United States
regulation employers must establish a written respiratory protection program meeting the requirements of the
Occupational Safety and Health Administration (OSHA) Respiratory Protection standard 29 CFR 1910.134 and any
applicable OSHA substance specific standards. For additional information on this standard contact OSHA at

www.OSHA.gov. In Canada, CSA standard Z94.4 requirements and/or the requirements of the applicable jurisdiction

must be met. Contact an industrial hygienist or PAFtec Technical Service with questions concerning the applicability
of the respirator to your job requirements.

7

9. System Components

Figure 1 - System Components

8

PARTS OF THE RESPIRATOR

Your respirator can be used with either a standard filter (PAF-1102 / PAF-1103) or with a high capacity filter (PAF-

1003). The high capacity filter is used with a filter adaptor (PAF-0038) and both standard filters are used with a filter
cover (PAF-1095). Most functions of the respirator are the same regardless of which filter is being used. Where there
are differences they are explained in this manual.

Respirator with Standard Filter and Filter Cover

Respirator with High Capacity Filter and Filter Adaptor

Through this manual reference is made to various commonly-used components and features of the machine.
Familiarise yourself with these parts before reading the rest of the manual. See Figure 2.

Exhalation Valve

Figure 2 - Parts of the Respirator

Mask Release
Button

Adjust Button

Bellows

9

10. Controls and Indicators

POWER BUTTON

This button is used to switch between the three (3) operating Modes: “On”, “Standby” and “Off”
Mode.

i) Standby Mode is when the green battery indicator lights are on, the motor is not running and

there is no airflow to the mask. The respirator will automatically switch to Standby Mode within ten
(10) seconds of the user taking it off. If the respirator is in Off Mode it will switch to Standby Mode when the Power
button is pressed.

ii) On Mode is when the respirator is being worn, the motor is running and there is air flow to the mask. The motor
will start (called On Mode) when the respirator detects a change in pressure in the mask triggered by your breathing.
In On Mode you should hear the motor running and feel the airflow on your face. You can also switch to On Mode
(start the motor) from Standby Mode by pressing the Power button once.

iii) Off Mode is when the green battery indicator lights are off and the motor is not running and there is no air flow to
the mask. The respirator automatically switches into Off Mode three (3) minutes after it has been removed from the
user’s face and the sensors detect that there is no breathing.

To conserve battery life, the respirator is designed to automatically switch from On Mode to Standby then to Off
Mode when not being worn.

Important: CleanSpace2™ switches into On Mode when it is in Standby Mode and the wearer starts to breathe. The
respirator can only switch into On Mode from Standby Mode.

FLOW TEST BUTTON

This button is used to check that the respirator is able to deliver its minimum designed flow. Pressing it
once, when the CleanSpace2 is in Standby Mode (not ON Mode), starts the flow test which lasts about 5
seconds. See Section 12 for instructions on running the flow test.

BATTERY INDICATOR LIGHTS

Your respirator is equipped with an indicator of battery charge. There are three (3) battery indicator
lights. With the charger plugged in and three green lights lit, the battery is fully charged and typically
has six (6) hours of operating time. The respirator should be fully charged before use.

If you need to be sure the battery is 100% charged plug in the charger. Even if the battery is fully charged, the 3rd

LED will flash for at least three minutes while the respirator checks its condition. Once all 3 LEDs light solidly

without flashing the battery is at 100%

For how to assess the level of charge, see Section 16.

When the battery approaches a level at which it would not be able to supply the Manufacturer’s Minimum Design

Flow, an alarm sounds (3 beeps, repeated once per second). All green battery lights are extinguished. If the low
battery alarm sounds you must leave the contaminated area immediately and recharge the battery.

10

Operating time is strongly affected by work rate, altitude, and other factors. The operating times quoted
above are average durations at moderate work rates at sea level. Actual operating times may vary widely
from average durations.

FILTER WARNING ALARM

CleanSpace2™ has a Filter Warning Alarm, which is triggered when the filter is blocked. If the Filter
Warning Alarm sounds (two beeps, repeated once per second) or the Filter Warning Alarm light
comes on, you must move out of the contaminated area, and change the filter.

11. Mask Fitting

Before you use your respirator you must determine the right mask for your face and know how to adjust the machine
to achieve a good fit.

It is vital that your mask is the right size for your face and fits properly. Mask fitting must be carried out by a
specialist / designated mask fitter. The fit must be confirmed by a quantitative fit test performed according to
OSHA regulations 1910.134.

To carry out a quantitative fit test your specialist mask fitter will require PAF-0025 PortaCount Adaptor and the
accompanying S005-7174 Quantitative Fit Test Instructions. The PortaCount Adaptor is an accessory that fits
between the mask and the exhalation valve and allows the air in the mask to be sampled. It comes with detailed
instructions on how to carry out a quantitative fit test.

No PAPR can fully protect you if you are not clean shaven. CleanSpace2 is not suitable for

users with facial hair.

MASK SELECTION GUIDELINES

No set of guidelines can ensure that you have the right size mask for your face. You must confirm the fit
with a quantitative fit test. But the table below will help your mask fitting specialist to select the mask most likely to

fit you, and may therefore save time.

11

Once you have achieved an acceptable mask fit and confirmed it with a quantitative fit test, record your information
in the table below.

Name

Mask Size

Neck Pad

Thick / Thin (Circle one)

Harness Front Straps
Position

(e.g. “4

th

hole from the end of the strap”)

Date of Quantitative Fit Test

Fit Factor on Test

IF A SATISFACTORY FIT FACTOR CANNOT BE ACHIEVED WITH ANY OF THE MASKS,

CLEANSPACE2 MUST NOT BE USED

12. Using CleanSpace2

Complete the following five steps each time you use your respirator.

STEP 1 - INSPECT
Before each entry into a contaminated area, the following inspections must be performed:



Visually check the entire respirator system including the blower, mask, harness, louvered filter cover or

filter adaptor and filter. If parts are missing or damaged replace them only with approved parts before
proceeding. Check the top and bottom case of the blower, and the Filter Adaptor for cracks or other
damage. Do not use the device if there is any damage.



Remove the HE filter and check it carefully. The seal must be clean and free from damage of any kind. If

necessary it can be cleaned with a cloth dampened with water. Examine the visible internal surfaces for
any sign that dust has leaked past a damaged seal. If found, replace the filter. The body of the filter must
not be cracked or show any sign of damage. Examine the filter carefully for any sign that it has sustained
an impact or been scratched. If any sign of impact or scratching is found, discard the filter. Refit the HE
filter (see Changing the Filter, below)

DO NOT USE COMPRESSED AIR OR A BRUSH TO CLEAN THE FILTER!

HEPA FILTERS ARE VERY EASILY DAMAGED BY THE USE OF COMPRESSED AIR OR BY

BRUSHING.

Misuse of CleanSpace2 by cleaning the filter may result in overexposure to contaminants and

lead to sickness or death.



Check that the battery is fully charged by pressing the power button. All three battery LEDs must light.

See Section 16.



Check both bellows for splits or holes. Check that the bellows have not become distorted so as to

partially or fully close the air path to the mask.



Check the mask to ensure that there are no cracks, tears or dirt; check the mask is not distorted.



Check the exhalation valve for damage or dirt build up. If it is dirty, remove the exhalation valve cover.

Remove any dirt, hairs or anything that could affect the seal of the valve against its seat. Check that the
valve seat is clean. Reinstall the valve cover. If the valve is damaged, replace the mask.



Check the harness is intact and has good elasticity. It must be adjusted to support some of the weight of

the respirator.

12

STEP 2 – CALIBRATE

This respirator contains a system for synchronising with your breathing and regulating mask pressure. This system
requires re-calibration whenever it experiences a change in temperature of more than 36°F (20°C). It is best
practice to also re-calibrate if the unit has been in storage, particularly if the storage temperature is not
known. To re-calibrate:

1. Remove the mask (if fitted). The Flow Test Cap must not be fitted.

2. Remove the filter from the respirator. If using a standard filter, close the filter cover. If using the Filter
Adaptor leave it in place. Place the respirator on a stable surface such as a table.

3. With the respirator in standby mode (one or more green LEDs lit), press and hold both the Power button
and the Filter Test button.

If no LEDs are lit, press the Power button once to enter standby mode.

4. When both the blue and red LEDs light, release both buttons. Leave the respirator sitting still.

5. After 5 – 10 seconds the motor will start and run for 5 – 10 seconds.

6. When the motor stops, calibration is complete.

7. Re-fit the filter.

Important Note: Failure to remove the filter prior to calibration will result in poor battery life. In order to restore
performance of the respirator, calibration must be performed again with the filter removed.

STEP 3 – TEST FLOW RATE

This test checks that the machine is able to deliver the Manufacturer’s Minimum Design Flow of 115 litres/minute.

1. Fit the yellow Flow Test Cap to the left bellow. See Figure 3.

Figure 3 - Flow Test

2. Make sure nothing is blocking the Flow Test Cap or the filter inlet. Place the respirator flat on a table or other
support.

3. Press and release the button marked “Flow Test”

4. The respirator automatically runs the Flow Test. The motor will run fast and air will be discharged from the
Flow Test Cap.

5. After 2 seconds the respirator reports the result of the test using the LEDs on the keypad. Use the table below
to interpret the LEDs.

To avoid unnecessary filter

changes, it is important to fit

the Flow Test Cap to the LEFT

bellow.

No air flows out of the right

bellow. Fitting the Flow Test

Cap to the right bellow will

result a FAIL result, even if the

filter is clean and battery fully

charged.

13

LIGHTS

Meaning

3 LEDs:

PASS (Excellent: flow >180 l/min)**

2 LEDs:

PASS (Good)**

1 LED:

PASS (Acceptable)

ALL LEDs
FLASH

FAIL (Flow <115 l/min)
Do not use the respirator until a new filter has been fitted and / or battery charged

and the test has been repeated with a PASS result.

Reset the respirator by pressing the Power button. Fully charge the battery and / or
replace the filter. Repeat the flow test. If filter is new and battery fully charged but the
respirator fails the test, contact PAFtec and do not use until it has been evaluated

** This test is not a battery charge test. Three LEDs means that, as of the moment it is tested, the unit can
deliver high flow. It does not mean the battery is full. You must check the battery condition separately. See
Section 16.

6. Remove the yellow Flow Test Cap and store for later use.

STEP 4 - DON THE RESPIRATOR

NOTE – please read STEP 4 all the way through before beginning to don the respirator

Locate your blower, mask, neck pad and harness. Make sure the mask and neck pad are of the size that you
used for your last successful quantitative fit test. These sizes should be recorded in this manual (see Section 11

above).



Fit a mask to CleanSpace2

Examine the mask AirClips. One is open and one is closed. Find the one that is closed. Seen
from above it is on the right hand side. See Figure 4

Locate the right hand blower AirClip. It is on the same side of the blower as the “Flow Test”
button. See Figure 5

Figure 4 - Right hand (closed) mask AirClip

Figure 5 - Right hand blower AirClip

Join the AirClip, so that the mask is attached to the blower. See Figure 6 and Figure 7.

14

Figure 6 - Join AirClip

Figure 7 - Mask on Blower (Note - connection is on
right hand side)

Check that the mask is the right way up! The pointed, nose section of the mask must face
up, in the same direction as the keypad. See Figure 8.

Figure 8 - Nose section of mask and keypad must both face up

Leave the other mask arm and bellow free until you are fitting the Respirator.

Familiarise yourself with the Adjust Buttons and the Mask Release Buttons. See Figure 9

Figure 9 - Mask Release Button and Adjust Button

15



Fit the Harness

Locate the strap on the harness that is made from loop-pile material. . This is the back strap.
If a neck pad is in place, remove it by pulling it away from the two strips of loop pile fabric on
the blower. Locate the section of hook material on the end of the back strap of the harness.
Fit the back strap of the harness to the blower by pressing the section of hook material on the
end of the strap against the two strips of loop pile material on the blower. See Figure 10.

Figure 10 - Harness Rear Strap

The two front straps of the harness fit to the AirClips on the mask. See Figure 11.

If unsure of your fitting, start with the 3rd hole from the end of the strap.

Figure 11 - Harness Front Strap

Make sure to use the same settings on the harness as you used in your last successful
quantitative fit test. These setting should be recorded in the table in Section 11



Fit a Neck Pad

The pad is fitted with two strips of hook fabric. Press these strips against the matching strips
of loop fabric on the blower. The centreline of the Neck Pad should align with the centreline
of the blower. Figure 1 shows the neck pad being fitted.

Rear strap fits behind neck pad

16

Figure 12 - Fitting neck pad

Make sure to fit the same size neck pad as you used in your last successful
quantitative fit test. The size (thick or thin) should be recorded in the table in Section
11



Loosen both bellows to their widest opening

Press the adjust button on the blower and pull on the bellows to extend them. See Figure 13.

Figure 13 - Adjust Button



Place the machine in Standby Mode

Press the Power button once



Don the respirator and start to breathe. (The motor should start)

Place the blower behind your neck with the bellows and mask hanging down one side. See Figure 14
Hold the mask in your left hand and the harness in your right. See Figure 15
Pull the mask around onto your face and the harness over your head. See Figure 16
Press your chin into the cup at the bottom of the mask and your nose into the top section of it.
Fasten the AirClip on your left hand side. See Figure 17 and Figure 18
Reach up and pull the harness forward to settle it on your head. See Figure 19

Press neck
pad into
place against
these strips

17

Figure 14 - Blower behind neck

Figure 15 - Left hand on mask,
right on harness

Figure 16 - Mask on face, harness
on head

Figure 17 - Fasten AirClip

Figure 18 - AirClip

Figure 19 - Settle harness

Breathe normally. The motor should start and you should feel fresh air on your face.
If the motor does not start, it was not in Standby Mode. Take the respirator off, press the

Power button to activate Standby Mode and don it again as described above.



Check the Harness

The Harness should take a little of the weight of the mask and support the blower so that the
respirator system sits level on your head. If necessary adjust the harness. This is mostly
done by shortening or lengthening the front straps of the harness, by moving between the
different button holes. Remember to shorten or lengthen each side by the same amount. The
length of the rear strap can be changed by adjusting the length of the top loop of strap where
it passes around an eye in the mesh “cap”. See Figure 20.To adjust the strap, doff the
respirator, adjust the strap, and don it again.

18

Figure 20 - Correct CleanSpace2 Position



Tighten the mask on your face

Tighten the mask until you do not feel any leaks
between the mask cushion and your face.

To tighten the mask, place one hand against the back
of the blower and the other over the front of the mask.
Push the blower forwards and the mask back,
tightening the fit. You will hear a series of clicks as the
mask is tightened. See Figure 21.

.
Be careful to tighten each side by the same amount

Figure 21 - Tightening Mask

STEP 5 – CHECK MASK SEAL

It is essential to do a fit check every time you wear a CleanSpace2

Locate PAF-1009, the red Seal Check Cap. Fit Seal Check Cap over the exhalation valve in the mask. The Cap
should snap into place. See Figure 22

.

Figure 22 - Fitting Seal Check Cap

Check that no air is flowing from the exhalation valve. Breathe normally.

Length of rear strap is
adjusted here

19

Using your fingers, feel around the perimeter of the mask for leaks. You will feel any leak as a cool flow of air over
your finger. For greater sensitivity breathe out firmly to raise the mask pressure. Wetting your fingers will make it
easier to feel tiny leaks.

If necessary tighten the mask. To tighten the mask, place one hand against the back of the blower and the other
over the front of the mask. Push the blower forwards and the mask back, tightening the fit. You will hear a series of
clicks as the mask is tightened.

Be careful to tighten each side by the same amount.
After each tightening, feel for leaks again

Tilt your head down (look at the ground) and up (look at the sky). Check that there are still no leaks. Look right and
left, checking for leaks. Adjust if necessary.

Once you can feel no leaks from the mask, the seal check is complete.

IF A SATISFACTORY FIT CANNOT BE ACHIEVED, DO NOT ENTER THE CONTAMINATED ZONE

Remove the Seal Check Cap by gently twisting the handle so that one side of the cap comes loose from the
exhalation valve. Be careful not to dislodge the exhalation valve cover. See Figure 23.

Figure 23 - Removing Seal Check Cap

Be sure to remove the Seal Check Cap before entering the contaminated area. The Cap blocks

the exhalation valve, making it more difficult for your exhaled air to be expelled from the mask.

Failure to remove the cap will lead to build-up of Carbon Dioxide in the mask, and may result

in headache or dizziness.

Never leave the Cap in place for more than 2 minutes!

13. Entering and Exiting the Contaminated Area

Prior to entering the contaminated area, complete the inspections and checks listed in these user instructions.

1. Ensure Seal Check has been done and motor is responding to your breathing

2. Check that none of the alarms are sounding.

3. Remember that if your workplace is very noisy you may not be able to hear the device alarms. In this

case you must follow the special precautions set out in Section 14.

4. Enter the work area

5. Do not remove the respirator until you have left the contaminated area, unless you have pressing health

reasons to do so (for instance you are experiencing dizziness and believe removing the respirator while
you leave the contaminated area may help).

6. Leave the contaminated area immediately if any of the following conditions occur:

a. Any part of the system is damaged
b. Airflow into the mask decreases or stops
c. The battery of filter alarms are triggered (even if only the audible or only the visible alarm

triggers)

20

d. Breathing becomes difficult
e. You feel dizzy or your vision is impaired
f. You smell or taste contaminants
g. Your face, eyes, nose or mouth become irritated
h. You suspect the concentration of contaminants may have reached levels at which this

respirator may no longer provide adequate protection.

7. You should have specific exiting and decontamination procedures as part of your workplace respiratory

protection program. Follow those procedures, together with the instructions below when removing the
respirator.

To remove the respirator, find the Mask Release Button (see Section 9) and press to release the mask from the
blower. See Figure 24.

The mask release button has a rough, dimpled finish that you can feel with your fingertips. All the other
buttons are smooth

Figure 24 - Mask Release Button

Note: The respirator motor will automatically switch off and go into Standby Mode in approximately 10 seconds
when no breath is detected. In Standby Mode, if after three (3) minutes no breath is detected, the Respirator will
automatically go into Off Mode. In Off Mode, all the battery indicator lights will be off and the motor will not be
triggered by the wearer’s breathing.

DO NOT REMOVE THE RESPIRATOR UNTIL YOU HAVE

VACATED THE CONTAMINATED AREA unless you have pressing health reasons to do so (for

instance you are experiencing dizziness and believe removing the respirator while you leave

the contaminated area may help)

14. Working in Noisy Environments

In most noisy environments the CleanSpace2 alarms are still clearly audible to the wearer. But if there is a chance
that you will not hear the alarms, you must take the following extra precautions

 Never enter the contaminated zone unless all three green battery indicator lights are illuminated
 Never work in the high noise area for more than four (4) hours. At the end of four hours, leave the

contaminated zone and check that

o The filter blocked light is not illuminated; AND
o All three green battery indicator lights are still illuminated

 If two or fewer green battery indicator lights are illuminated, recharge CleanSpace2 until 3 lights are

showing again (and the 3rd one has stopped flashing)

 If the filter blocked light is illuminated, change the filter
 Be particularly aware of difficulty breathing or of the air flow stopping. If these things happen, exit the

contaminated zone immediately.

21

15. Fitting & Changing the Filter

Before using the respirator you must ensure that you are using the correct filter type for the environment you are
working in.

IT IS ESSENTIAL THAT THE CORRECT FILTER TYPE IS SELECTED

FOR THE CHOSEN APPLICATION.

Before changing the filter, move out of the contaminated area and remove the respirator. Used filters should be
disposed of responsibly and treated as non-recyclable hazardous* waste (* dependent on the contaminant being
filtered). Filters need to be regularly changed. The frequency of change depends on use and concentration of
contaminants in the atmosphere.

BLOCKED FILTER ALARM

All CleanSpace respirators have a Filter Blocked alarm, which is triggered when the filter requires replacement (2
beeps, repeated every second).

If the blocked filter alarm is triggered (2 beeps, repeated every second, red LED flashes), leave

the contaminated area immediately and replace the filter.

Operating the respirator after the blocked filter alarm has sounded can cause the flow to fall

below the manufacturer’s minimum designed flow, which may result in overexposure to

contaminants and lead to sickness or death.

(Pressing the Power button once will mute the Filter Blocked alarm, allowing you to concentrate while you exit the
contaminated zone. After 15 minutes, if the filter has not been changed, the alarm will resume).

WHEN TO CHANGE THE PARTICULATE FILTER

Change the filter

 When the Blocked Filter Alarm sounds
 If the Flow Test indicates that the respirator is not able to produce the Minimum Design Flow.
 If there is any sign of damage to the filter
 When the filter reaches its expiry date (marked on the filter label)
 When the outside of the filter is heavily soiled
 When the filter is wet
 If there is any sign of dust or contaminants on the inside surface of the filter.

A respirator with a clean filter will run for much longer than one with a filter that is dirty. To maximise your work time
between battery charges, it is best to change the filter more often.

CleanSpace™ filters are NOT reusable and must NOT be cleaned.

DO NOT USE COMPRESSED AIR OR ANY OTHER MECHANICAL METHOD TO CLEAN THE FILTER!

HEPA FILTERS ARE VERY EASILY DAMAGED BY THE USE OF COMPRESSED AIR OR BY BRUSHING.

Misuse of CleanSpace2 by cleaning the filter may result in overexposure to contaminants and

lead to sickness or death.

22

CHANGING THE STANDARD FILTER (PAF-1102/ PAF-1103)

To unlock the filter cover, lift the pin located on the end of the filter cover. The filter cover will swing open exposing
the used filter. Remove the filter.

Check that the area where the filter sits is clean. If necessary wipe it with a clean cloth or CleanSpace Cleaning
Wipe.

Fit a new filter. Swing the filter cover back into closed position and hold it firmly against the body of the respirator
with one hand. Press the pin down until clicked back into place.

Check that the blocked filter alarm is working, as described below.

WHEN FITTING A NEW FILTER THE BLOCKED FILTER ALARM SHALL BE TESTED

BEFORE THE RESPIRATOR IS PUT BACK INTO SERVICE. SEE “TESTING THE

BLOCKED FILTER ALARM” AT THE END OF THIS SECTION

USING THE HIGH CAPACITY FILTER (PAF-1003)

The high capacity HEPA filter requires the use of an adaptor. Follow the steps below to fit the Adaptor.

Figure 25 - Fitting the Filter Adaptor

(Note adaptor shown without “Hoop”, which does not affect fitting or removal)



The Filter Adaptor comes with a 3mm hex key. The 3mm hex key can be found clipped on to the inside

the Filter Adaptor.

23



Remove the Filter Cover by lifting the pin located at one end and open the cover.



Using the hex key, remove the bolt at the opposite end of the Filter Cover. The Cover can now be lifted away

and stored.



Fit the Filter Adaptor to the back of the respirator. Ensure the adaptor is correctly aligned with the silver

CleanSpace logo facing up - the same side as the keypad.



Replace and tighten the bolt using the hex key to secure one end of the Filter Adaptor. Before replacing the

pin, pivot open the Adaptor out from the respirator and clip the hex key back into place to store.



Press the Adaptor against the unit and push the pin back into place. The Filter Adaptor is now ready to use.

 (To remove the Filter Adaptor, simply reverse the steps above)

CHANGING THE HIGH CAPACITY FILTER (PAF-1003)

STEP 1. Removing the filter from the filter adaptor

 Turn the respirator upside down. Using your thumb, move the Latch Lock out of the way and then pull the

Latch firmly away from the filter. The filter can now be removed. See Figure 26.

Figure 26 - Removing HEPA Filter

STEP 2. FITTING A NEW FILTER TO THE FILTER ADAPTOR

 Clean the sealing surfaces on the adaptor and on the filter.
 Hold the new filter so that the blue seal is facing the adaptor. Locate 2 ribs on the filter body into the slots in

the top of the filter adaptor and rotate the filter into place. See Figure 27

 Snap the latch firmly over the 2 ribs on the bottom of the filter body. You will hear 2 clicks when the filter is

positioned correctly. Note: The latch lock will move to one side automatically. See Figure 27.

 The filter is now sealed to the respirator and ready to use.
 Check the blocked filter alarm as described below

Figure 27 - Fitting a new HEPA Filter

Use only NIOSH-approved CleanSpace™ filters with the respirator. If used with other filters

CleanSpace2 is not NIOSH approved. Use of other filters may result in overexposure to

contaminants and lead to sickness or death.

24

WHEN FITTING A NEW FILTER THE BLOCKED FILTER ALARM SHALL BE TESTED BEFORE

THE RESPIRATOR IS PUT BACK INTO SERVICE. SEE “TESTING THE BLOCKED FILTER

ALARM” AT THE END OF THIS SECTION

TESTING THE BLOCKED FILTER ALARM

After changing the filter, check that the Blocked Filter Alarm is audible and the Filter LED is working. Do not
fit the Flow Test Cap for this test.

1. To prepare for this test you must completely block the entry to the filter.

a. If using a standard filters, open the filter cover and place your hand to completely cover the filter

grille (see picture below).

b. If using the high capacity filte, stand the machine on a flat surface so that the inlet to the filter is

completely blocked (see picture below).

2. With the respirator in Standby mode (one or more green LEDs lit), press and release the Power button. The

blue LED will light and the respirator starts blowing.

If no LEDs are lit, press the Power button once to enter Standby mode.

3. After 5 - 10 seconds, the red Filter LED will light and the blocked filter alarm will sound (2 beeps, repeated

every second).

4. Reset the machine by pressing the Power button.

If the red Filter LED does not light or the alarm does not sound, check that the inlet of the filter is completely
blocked. If the Filter LED and/or audible alarm are still not working, do not enter the contaminated
zone. Contact PAFtec for assistance.

Figure 28 - Blocking the standard filter

Figure 29 - Blocking the high capacity filter

25

16. Battery Information

CleanSpace2 is not intrinsically safe. Do not use in flammable or explosive atmospheres.

Doing so may result in injury or death.

Always correctly use and maintain the internal lithium ion battery packs. Failure to do so may

result in fire or explosion or could adversely affect respirator performance and result in injury,

sickness or death.

- Do not charge the on-board battery with unapproved chargers, in enclosed cabinets without

ventilation, near flammable liquids or gasses, or near sources of high heat

- Do not immerse the device in water

- Do not use, charge or store the device outside the recommended temperature limits

ASSESSING STATE OF CHARGE

The three LEDs on the control panel indicate the level of charge. When the unit is in use (not on charge) they work
like a fuel gauge allowing you to estimate your remaining work time. When the unit is on charge, the 3rd LED turns on
solidly (no flashing) only when the battery is fully charged (100%), making it easy for you to tell when the unit is
100% charged.

If you need to be sure the battery is 100% charged plug in the charger. Even if the battery is fully charged, the 3rd

LED will flash for at least three minutes while the respirator checks its condition. Once all 3 LEDs light solidly

without flashing the battery is at 100%

With the unit NOT on charge

Green LEDs

Charge

Approximate Run Time*

85 - 100%

4 – 8 hours

15 – 85%

1 – 4 hours

5 – 15%

Recharge! (20min to 1 hour)

* Operating time is strongly affected by work rate, altitude, and other factors. The operating times quoted

above are average durations at moderate work rates at sea level. Actual operating times may vary widely
from average durations.

CHARGING THE INTERNAL BATTERY

The internal battery must only be charged with a
CleanSpace charger.



To charge the internal battery, turn the

respirator upside down, and locate the
charging port. See Figure 30 - Charging Port



Lift off the flexible polymer charging port

cover. Slide the charger cable connector into
the charging port. Ensure the charger is
plugged into a power socket.

Turn the respirator over and check that one of the green LEDs on the keypad is flashing. If none of the
LEDs is flashing, the unit is not charging. Check that the charger is plugged into the wall socket and the
charger cable is plugged securely into the socket on the underside of the respirator. If the respirator is still not
charging, contact PAFtec Customer Service on 1 888 804 0038

Figure 30 - Charging Port

26



Charging is complete when the blower shows three (3) green solid lights. If the third green LED is

flashing rapidly, charging is 95% complete.



When the respirator is fully charged, disconnect the charger cable from the blower charging port.

IMPORTANT Ensure you replace the charging port cover to prevent dirt and contaminants getting into
the port.



Note: The battery can only be charged at temperatures between 32°F and 95°F (0°C and 35°C). Outside

this temperature range no charging will occur.

Do not charge the battery in electro-magnetically noisy environments, such as near welding machines. Doing so

may damage the CleanSpace2 electronics.

Do not leave the respirator plugged into its charger for more than one week at a time. Doing so may shorten the

battery life.

LOW BATTERY ALARM

Your respirator has a low battery alarm, which is triggered when the battery has approximately 5 minutes life
remaining (3 beeps, repeated every second). You cannot mute the low battery alarm except by connecting the
respirator to its charger or by stopping the motor (doff the respirator and either press the Power Button once or allow
the respirator to detect that there is no breathing and stop)

When the battery voltage becomes extremely low, the motor will stop.

If the battery alarm sounds (3 beeps, repeated every second), leave the contaminated area

immediately and re-charge the battery.

Operating the respirator after the low battery alarm has sounded can cause the flow to fall

below the manufacturer’s minimum designed flow, which may result in overexposure to

contaminants and lead to sickness or death.

GENERAL BATTERY INFORMATION

Your respirator has an internal lithium ion (Li-ion) polymer battery. Lithium ion (Li-ion) batteries have the highest
energy density of all battery types, and are widely used today in portable electronic devices across many different
industries. The commonly available Li-ion polymer batteries are similar to Li-ion batteries, except they are packaged
in a soft polymer film as opposed to the metal case commonly used for Li-ion cells. The soft packaging allows the
cells to expand slightly under extreme heat, making them safer in fault conditions. CleanSpace respirators use
quality Li-ion polymer batteries and are designed to be viable over a minimum of 500 complete charge and discharge
cycles while still maintaining at least 70% of their specified full capacity.

RESPIRATOR STORAGE

To maintain the integrity of the internal battery, the respirator must be stored under the following conditions when not
being used:

Long term storage (> 30 days) 30% - 50% RH, 65°F to 82°F (18°C to 28°C)
Short term storage (< 30 days) 30% - 50% RH, 14°F to 95°F (-10°C to 35°C)

The following precautions must be followed during use:



Avoid mechanical shocks or impacts from any sharp or hard objects



Do not use or place the respirator in extreme heat, such as in direct sunlight, near heat sources, etc. The

battery will be damaged if its temperature rises above 212°F (100°C). Note: The respirator will stop
functioning if its internal temperature rises above 140°F (+60°C) or falls below 14°F (-10°C)



Do not dispose of the respirator in a fire



Do not use the respirator in heavy rain, or allow it to get wet or immersed in liquid



Do not disassemble the blower case, there are no user serviceable parts inside



Do not use the respirator if there are any signs of severe mechanical damage

IN THE EXTREMELY RARE CIRCUMSTANCE THAT THE BATTERY

IS DAMAGED AND ELECTROLYTE COMES IN CONTACT WITH EYES,

FLUSH WITH WATER IMMEDIATELY AND SEEK URGENT MEDICAL ATTENTION

27

17. Cleaning

We recommended that you clean your respirator after every use. The mask, blower, neck pad and harness need to
be cleaned separately. Disassemble the mask, neck pad and harness from the blower before cleaning. CleanSpace
Cleaning Wipes are recommended as a simple and effective method of cleaning the blower and masks.

CLEANING THE MASK

There are two methods for cleaning the mask. Before washing the mask, remove the valve cover covering the
exhalation valve leaf. To remove the valve cover, find the small inlet located under the lower, inside edge of the
valve. Use your finger nail to unclip and push up the valve cover. See Figure 31.

The valve cover is easily fitted back by placing it with the clip aligned to the inlet on the valve seating and pushing
down. The valve cover will gently snap back into place.

Figure 31 - Removing Exhalation Valve cover

1. CleanSpace Non-Alcohol Wipes for face piece



CleanSpace Cleaning Wipes are impregnated with benzalkonium chloride, a bactericidal solution ideally

suited for silicone face pieces.



To clean the exhalation valve, remove the valve cover (using the instructions above), gently wipe the leaf

edge. Replace the valve cover before use.

2. Hand wash in warm soapy water



Wash the mask thoroughly with a mild detergent in warm water (less than 122°F (50°C)).



A soft brush or sponge can be used to remove any stubborn dirt or grit



To clean the exhalation valve, gently wash the warm water solution through the valve and use a sponge

to gently clean the valve surface



Rinse the mask and valve well in warm running water. IMPORTANT: If the mask is not rinsed thoroughly,

residue from cleaning solution may irritate the wearer’s skin or cause the valve to stick. Replace the

valve cover before use.

Drying the mask

After cleaning, allow the mask to air dry in a clean environment, valve up to prevent water pooling. Note: Do not dry
the mask by exposing directly to heat i.e. hair dryers or heaters. The mask can also be hand-dried with a clean, lint­free cloth. IMPORTANT: Cleaning can cause the exhalation valve leaf to stick. Before use, check that the exhalation
valve leaf operates freely by gently lifting the valve. Replace the valve cover before use.

WARNING: NEVER DRY THE MASK OR EXHALATION VALVE WITH A CLOTH THAT MAY LEAVE BEHIND LINT.

Lint contamination of the exhalation valve may cause it to leak, resulting in overexposure to

contaminants and lead to sickness or death.

28

CLEANING THE BLOWER

WARNING: The blower contains a battery, sensitive electronics and a motor. NEVER immerse

it in water or use anything wetter than a damp cloth to clean it.



After removing the mask, remove the neck pad. Leave the filter in place to prevent any dust or liquids

from getting into the blower.

WARNING: NEVER CLEAN THE FILTER WITH COMPRESSED AIR OR A BRUSH. HEPA FILTERS ARE EASILY

DAMAGED BY THE USE OF COMPRESSED AIR OR BY BRUSHING.

Misuse of CleanSpace2 by cleaning the filter may result in overexposure to contaminants and

lead to sickness or death.



Use a gentle brush to remove any dirt, grit or fibres from the Velcro attached to the blower.



Using CleanSpace Cleaning Wipes, wipe down the outside of the blower. The blower can also be

cleaned with a damp cloth.



Allow the blower to air dry in a clean environment. The blower can also be hand-dried with a clean lint-

free cloth. Note: Do not dry the blower by exposing to heat (i.e. hair dryers or heaters) or

compressed air.

CLEANING THE HARNESS AND NECK PADS

The harness and neck pads can be washed in warm soapy water or machine washed. After cleaning, allow the
harness and neck pads to air dry in a clean environment.

Note: Do not dry the harness or neck pads by exposing directly to heat i.e. hair dryers or heaters

18. Periodic Maintenance & Checking

Recalibration

You must recalibrate the internal pressure sensor any time that your CleanSpace2 is exposed

to changes in temperature of more than 36°F (20°C). ). It is best practice to also re-calibrate if the

unit has been in storage, particularly if the storage temperature is not known.

See Section 12 for how to calibrate your respirator.

29

19. Specifications

Air Flow

Greater than 115 litre/minute

Breath-responsive, with max inflow to mask 115 – 200 litre per minute, dependant on altitude, filter
and battery condition.

Operating
Temperature
Range

14°F to 113°F (-10°C to 45°C)

The motor will shut down while the temperature of the battery pack is above 140°F (60°C) or below
14°F (-10°C)

Operating
Humidity
Range

Zero to 90%, non-condensing

Operating
Altitude
Range

Approximately sea level to 5800 feet (1770m)

Charging
Temperature
Range

32°F to 95°F (0°C to 35°C)

Below 32°F (0°C) and above 95°F (35°C) the battery will not accept charge

Storage
Conditions

Short term storage under 30 days:

Out of direct sunlight, in a clean, dry environment (30% - 50% RH), 14°F to 95°F (-10°C to 35°C).

To maintain the integrity of the internal battery, the respirator must be stored under the following
conditions when it will not be used for longer than 3 months

Long term storage (> 30 days):
Out of direct sunlight, in a clean, dry environment (30% - 50% RH), 65°F to 82°F (18°C to 28°C).

Shelf Life
(when
stored as
specified)

Blower (limited by internal battery): 6 months

We recommend to charge the battery every 3 months if the device is not in use.

HE Filter: 5 years
Battery Type

Lithium Ion Polymer

Run Time

Approximately 4.5 – 8 hours.

Run time is strongly influenced by work rate, filter condition, altitude and other factors. The run time
specified above assumes moderate work rates at sea level with a clean filter. Different conditions will
produce widely varying run times.

Recharge
Time

2 hours (to 95%)

Low Battery
Voltage
Alarm

Triggers when the remaining run time is around 5 to 10 minutes.

Audible alarm, 3 beeps, repeated every second, 75dB(A) at ear.

Filter
Blocked
Alarm

Triggers when the filter requires replacement.

Audible alarm sounds until a key is pressed, 2 beeps repeated every second, 75dB(A) at ear plus
red filter LED flashes. When the alarm first sounds, and if the battery is almost completely run flat,
the maximum flow that can be delivered has been reduced to about 140 litre/minute.

30

Charger

Input: 100 – 240VAC, 50 – 60 Hz

Weights

PAF-1002 blower with Filter Adaptor PAF-0038, PAF-0016 Neck Pad Thin, PAF-0030 Harness and
PAF-1003 HEPA Filter fitted: 24.3 oz. (690 gram)

PAF-1002 blower with standard filter PAF-1102/PAF1103 and filter cover PAF-1095, PAF-0030
Harness and PAF-0016 Neck Pad Thin: 18.3 oz. (520 gram)

Masks: 4.2 to 5.3 oz. (120 to 150 gram)

Intrinsic
Safety

CleanSpace2 is not an intrinsically safe system

20. Product and Accessory information

Refer to the NIOSH approval matrix for approved combinations

Blower, Filter Cover, Filter Adaptor

Product Code

Description

PAF-1002

Blower

PAF-1095

Filter Cover

PAF-0038

Filter Adaptor

Filters

Product Code

Description

PAF-1102

Filter HE Standard Synthetic

PAF-1103

Filter HE Standard Glass

PAF-1003

Filter HEPA High Capacity

Masks

Product Code

Description

PAF-0033

Mask: H Series Small

PAF-1010

Mask: H Series Medium

PAF-0027

Mask: H Series Large

Harness, Neck Pads

Product Code

Description

PAF-0030

Harness

PAF-0014

Neck Pad - Thick

PAF-0016

Neck Pad - Thin

PAF-1005

Flow Test Cap

Accessories

Product Code

Description

PAF-0032

CleanSpace™ Cleaning Wipes (100 pack)

PAF-0025

PortaCount Adaptor for Fit Testing

PAF-1009

Seal Check Cap

31

21. Product Warranty

This product has been manufactured using quality parts and processes.
PAFtec Australia Pty Ltd warrants that the product is free from defective workmanship and parts for a period of one

(1) year from the date of original purchase provided the product has been used, cleaned and maintained in

accordance with these instructions and PAFtec’s recommendations. This warranty does not include consumable

parts, such as filters and face masks, which must be replaced regularly by the user. Consumable parts are
warranted up to the point of use, provided they have been stored correctly and are within their expiry date.

This warranty does not cover:



Where the product has been used for industrial purposes outside the recommendations of PAFtec

Australia Pty Ltd;



Where damage has been caused by misuse, neglect, accident, or excessive wear and tear.

Any claim under this warranty must be made within one (1) year of the date of purchase of the product. All warranty
claims must be made by returning the defective product to your supplier together with the proof of purchase. The
purchaser is responsible for all freight. In the event that any part of the product is found by PAFtec to be defective,
PAFtec will either repair or at its discretion replace the faulty part.

This warranty is given by:
PAFtec Australia Pty Ltd

(ABN 24 146 453 554),
Ground Floor, 16-18 Carlotta Street
Artarmon NSW 2064 Australia;
T. 1 888 804 0038
E. [e-mail]

This warranty is provided in addition to other rights and remedies you have under law. You are entitled to
replacement or refund for a major failure. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure.

Disclaimer:

Whilst Paftec has made every effort to ensure that the details and information given in both our printed and online
publications are accurate at the time of issue, full technical specifications are not necessarily included. Furthermore
Paftec has a policy of continuous improvement and the right is reserved to alter details and information as the need
arises. Accordingly the Customer should check any details and information they wish to rely on with Paftec at the
time of purchase. Paftec cannot accept liability in respect of any errors or omissions herein contained or for any loss
or damage malfunction or consequential loss arising from reliance upon our publication.

The Customer will be responsible for any risk to health or safety from goods in the Customer’s possession and/or

control. The Customer’s attention is drawn to the fact that statutory regulations and recognised codes of practice

exist covering the use and handling of some goods (including safety products). The Customer must ensure that
persons who use the goods receive adequate training and safety literature.

©2017 Paftec Australia Pty Ltd. All rights reserved.
No page or part of this manual may be reproduced in any form without written permission of the copyright owner

shown above. Paftec reserves the right to correct typographical errors. All information is correct at the time of going
to print.

32

PAFtec Australia Pty Ltd
ABN 24 146 453 554

Ground Floor, 16-18 Carlotta Street, Artarmon NSW 2064 Australia
T: 1 888 804 0038 |E: [e-mail]

S005-7160 Rev 8, 25 SEPT 2017

Released on Change Note ECN0905