CleanFreak CPL1500HS Owner's Manual

MODEL#
MODEL# MODEL#
MODEL#
CPL
CPLCPL
CPL
1500HS
1500HS1500HS
1500HS
SERIAL#
SERIAL# SERIAL#
SERIAL#
TABLE OF CONTENTS
Safety Precautions
Machine Operation
Machine Maintenance & Storage
Handle Release Assembly Instructions
Parts List
Wiring Diagram
2
3
4
4
5
6-10
11
SAFETY PRECAUTIONS
!!! This machine must be grounded! Grounding provides the path of least resistance for electrical current. To reduce the risk of electrical shock should the machine malfunction, the machine has a special grounding plug. Do not remove the ground pin under any circumstances!
This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories.
All operators shall read, understand and exercise the following safety precautions:
1) Do not operate machine:
- Unless trained and authorized.
- Unless you have read and understand operators manual.
- In flammable or explosive areas.
- With damaged cord or plug.
- If not in proper operating condition.
- In outdoor areas.
- In standing water.
- With the use of extension cords.
2) Before operating machine:
- Make sure all safety devices are in place and operate properly.
3) When using machine:
- Only use approved burnishing pads.
- Do not run machine over cord.
- Do not pull machine by cord or plug.
- Do not pull cord around sharp edges or corners.
- Ensure the dust collection bag is in place and is tightly sealed to the machine.
- Turn power switch to off prior to unplugging machine.
- Do not unplug by pulling on the cord.
- Do not stretch cord.
- Do not handle plug with wet hands.
- Keep cord away from heated surfaces.
- Do not pick up burning or smoking debris such as cigarettes, matches or hot ashes.
- Report machine damage or faulty operation immediately.
4) Before leaving or servicing machine:
- Turn off machine.
- Unplug cord from outlet.
5) When servicing machine:
- Unplug cord from outlet.
- Use manufacturer supplied or approved replacement parts.
To avoid electrical shock, please
replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person .
-3-
Operation of High Speed Burnisher
* READ OPERATORS MANUAL
THO
ROUGHLY PRIOR TO OPERATING OR
SERVICING THIS MACHINE.
GENERAL USE
1. Remove any obstructions or other
obstacles in the area which is to be cleaned.
2. Place the handle in the upright position and tilt machine back until handle rests on the floor
* Be sure the machine is not plugged into
an outlet
3. Attach the pad to the machine by first
unscrewing the male end of the big mouth from the flexible pad driver. Place the approved pad on the pad driver, place the male end of the big mouth into the center hole of the pad, and tighten the big mouth firmly to the pad driver.
4. Place machine back into its upright position.
5. Plug power cord into a grounded outlet.
* Never use an extension cord in
conjunction with the standard power cord.
6. The handle height may be adjusted by
lifting up the compression handle which is located on the right side of the handle tube about 1 foot above floor level. Release the compression handle and adjust handle to safe operating height, then push back down on the compression handle to lock the handle in operating position.
7. To start the machine, press the red safety button on the top of the upper switch housing, and then squeeze either of the operating triggers. (the safety button must be depressed prior to squeezing the operating triggers.)
8. When the machine is in operation, both hands should be placed on the switch housing (upper handle).
9. To stop the machine at any time, simply release the operating trigger(s) and the machine will stop automatically.
MAINTENANCE
To keep the machine performing well for many years, please follow the following maintenance procedures.
* Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1. Unplug machine as soon as you are done using it.
2. Clean the outside of the machine with a mild cleaner.
3. Check power cord for any damage. If
damage is detected, replace power cord immediately.
4. Lubricate wheels with a water resistant lubricant once a month.
5. Check machine for loose or missing nuts and bolts, and replace as necessary.
6. If the machine is used in a dusty environment, you may remove the motor cover and blow the motor clean with compressed air. This will ensure proper ventilation, and allow the motor to run cooler.
STORAGE
1. Unplug machine from power source and wrap cord on handle.
2. Tilt machine so the pad is not touching the floor.
3. Store machine in upright position and in a dry area.
-4-
Loading...
+ 7 hidden pages