Page 1
Solenoid Control Valve
Performance Specification
Capacity: See Technical Data Sheet
CfFactor: 0.9
Cavitation: See Technical Data Sheet
Rangeability: 500:1
Bearing Friction: No friction from slip-type
bearings
Design Specification
Sizes: 2, 3, and 6 inch wafer style
6, 8, 10, and 12 inch flanged
End Detail Wafer: Fits ANSI B16.5 class 125,150,
250, and 300 flanges
End Detail Flanged: ANSI B16.5 class 150
(fits class 125) or
ANSI B16.5 class 300
(fits class 250)
Operating Pressure: 720 psi maximum
Maximum Differential: 150 psid continuous,
Reverse Pressure
Temperature Range: 32 to 160 degrees F*
Flange Operating Pressure: Class 125-175 psi maximum
Solenoid Enclosure: NEMA IV Watertight (std)
Solenoid Voltages: 115, 230, 460 for 50, 60 HZ
Standard natural rubber 65 durometer in water service.
*
Temperature range depends on liner material. Higher differential
pressure ratings available.
For other than standard ANSI flanges consult factory
: 125 psid maximum
225 psid intermittent*
Class 150-275 psi maximum
Class 250-300 psi maximum
Class 300-720 psi maximum
NEMA Vll Explosion Proof
(available)
6,12, 24,120, 240 VDC
Din drilling available on all sizes
MODEL
736-01
• Fast Acting Solenoid Control
• Reliable Drip-Tight Shut-Off
• Simple Design, Proven Reliable
• Optional Check Feature
• Easy Installation & Maintenance
Description
The
Cla-Val Model 736-01 Solenoid Control Valve is an on-off control
valve which either opens or closes upon receiving an electrical signal
to the solenoid pilot control. This valve consists of a Cla-Val Model
100-42 main valve and a three-way solenoid valve which alternately
applies pressure to or relieves pressure from the loading chamber of
the main valve. It is furnished either normally open (de-energize solenoid
to open) or normally closed (energize solenoid to open).
If the check feature option is added and a pressure reversal occurs, the
downstream pressure is admitted into the main valve loading chamber
and the valve closes to prevent return flow.
Purchase Specification
The three-way solenoid pilot alternately applies pressure to or
exhausts pressure from the loading chamber of the main valve which
in turn causes the main valve to open or close.
The control valve shall be constructed of two parts: a stainless steel
body, and an elastomeric liner or control element. Minimum rangeability
shall be 500:1 based on capacity at flowing pressure conditions. C
shall be greater than or equal to 0.9. Valve and control system shall
be similar in all respects to Cla-Val Model 736-01 as manufactured
by Cla-Val, Newport Beach, California.
Material Specification
Body: 316L Stainless Steel
Liner: Natural Rubber, 65 durometer (standard)
Viton, EPDM, Nitrile, Silicone (available)
Liner Retainer: 316 Stainless Steel
Solenoid Pilot
Body: Brass*
Wetted Parts: Brass/Stainless Steel*, Buna-N
®
Accessories
Shut-off Isolation Valve: Brass*
Speed Controls: Brass*
Check Controls: Brass*
“Y” Strainer: Bronze*
Control Piping: Copper*
Control Fittings: Brass*
*316 stainless steel available
f
Page 2
F
B
3
D1
C
2
B
1
D2
S
B
H
DRAIN TO
ATMOSPHERE
INLET OUTLET
INDEPENDENT
OPERATING
PRESSURE
CS3
3
1
2
736-01 Basic Components
PO Box 1325 Newport Beach CA 92659-0325
Phone: 949-722-4800 Fax: 949-548-5441
CLA-VAL
CLA-VAL CANADA CLA-VAL EUROPE
4687 Christie Drive
Beamsville, Ontario
Canada L0R 1B4
Phone: 905-563-4963
Fax: 905-563-4040
Chemin dés Mesanges 1
CH-1032 Romanel/
Lausanne, Switzerland
Phone: 41-21-643-15-55
Fax: 41-21-643-15-50
©COPYRIGHT CLA-VAL 2014 Printed in USA
Specifications subject to change without notice.
www.cla-val.com
"E" N.P.T.
"E" N.P.T.
"E" N.P.T.
"D"
DIA.
"B"
DIA.
"C"
6", 8",10" and 12" Flanged Style
3/8" N.P.T.
3 PORTS
"A" TYP.
"BB"
DIA.
FLOW
"CC"
2", 3", 4" and 6" Wafer Style
Item Description
1 100-42 Roll Seal Main Valve
2 CS3 Solenoid Control**
3 X43 "Y" Strainer
Optional Features
Item Description
B CK2 (Isolation Valve)
C CNA Needle Valve (Closing)*
D Check Valves (125 psid max.
reverse pressure)
F Independent Operating Pressure
H Atmospheric Drain
S CNA Needle Valve (Opening)*
* The opening & closing speed controls (optional) on this valve
should always be open at least 1⁄4 turn off their seats.
** Solenoid requires operating voltage, enclosure
type, and normally open or normally closed main valve.
Dimensions (100-42 Main Valve)
Valve Size (Inches) 2 3 4 6 8 10 12
A 27⁄8 39⁄16 41⁄8 51⁄4 -- -- --
B -- -- -- 107⁄8 143⁄8 18 215⁄8
BB 43⁄8 57⁄8 73⁄8 913⁄16 -- -- --
C -- -- -- 9 11 13 151⁄4
CC 21⁄2 31⁄4 4 51⁄2 -- -- --
D (ANSI 150) -- -- -- 11 131⁄2 16 19
D (ANSI 300) -- -- -- 121⁄2 15 171⁄2 201⁄2
E (Ports) NPT -- -- -Approx. Wt. (150 lbs.) 4 71⁄2 14 58 115 190 290
Approx. Wt. (300 lbs.) 4 71⁄2 14 87 155 250 375
Max. Continuous Flow (gpm) 224 469 794 1787 3177 4964 7148
Valve Size (mm for ANSI) 50 80 100 150 200 250 300
A 73 90 105 133 -- -- -B -- -- -- 276 356 457 549
BB 111 149 187 249 -- -- -C -- -- -- 229 279 330 387
CC 64 83 102 140 -- -- -D (ANSI 150) -- -- -- 279 343 406 483
D (ANSI 300) -- -- -- 318 381 445 521
E (Ports) NPT -- -- -Approx. kg. (150 lbs.) 1.81 3.63 6.35 30 54.43 89 151.5
Approx. kg. (150 lbs.)with Studs & Nuts 2.72 4.54 10 -- -- -- -Approx. kg. (300 lbs.) 1.81 3.63 6.35 41.73 72.57 116.57 191
Approx. kg. (300 lbs.)with Studs & Nuts 5 6.35 11. 8 -- -- -- --
Max. Continuous Flow (l/s.) 14 30 50 113 200 301 451
NSF Approved 2" thru 12"
When Ordering Please Specify:
1. Catalog No. 736-01 2. Valve Size 3. Fluid Being Handled 4. Fluid Temperature Range 5. Inlet Pressure Range
6. Outlet Pressure Range 7. Maximum Differential Pressure 8. Minimum Differential Pressure
9. Maximum Flow Rate 10. Voltage & NO, NC (Main Valve)
E-736-01 (R-07/2014)
3
3
⁄8
3
⁄8
1
⁄8
3
⁄8
1
⁄2
⁄2
1
1
⁄2
⁄2
Represented By:
Loading...