Clas Ohlson HD-420 User Manual

HDMI Switch

HDMI-växel
HDMI-veksler
HDMI-vaihde
HDMI-Umschalter

Art.no. Model

38-2878 HD-4200

EnglishSvenskaNorsk

Suomi

Deutsch

Ver. 20130605

HDMI Switch with
Remote Control

English

Art.no. 38-2878 Model HD-4200

Please read the entire instruction manual before use and save it for
future reference. We reserve the right for any errors in text or images
and for making any necessary technical changes to this document.
If you should have any questions concerning technical problems
please contact our Customer Services.

Safety

• The product should only be repaired by qualified service personnel.

• The product is made only for use indoors.

• Never open the casing. Certain components within the product’s

casing contain dangerous currents. Contact with these may give
you an electric shock.

• Do not place the product where it could fall into water or other
type of liquid. Never place the product close to objects that can
cause water or other liquid to spill over the product, e.g.
a vase or a drink.

• Only use the device with suitable or recommended adaptor.

Contents

• HDMI Switch

• Remote control

• AC/DC adaptor

• Instruction manual

2 3

Buttons and Functions

The front of the product

[SELECT OUT] 1 / 2 Choose which input is to be active.
1-4 Indicates which of the inputs is activated.
HDMI IN 4 A fourth input for simple connection of

e.g. video game.

IR Receiver for the remote control’s signal.

The back of the product

HDMI IN (1-3) Inputs for connection e.g. DVD player,

digital receiver, or video game.

HDMI OUT (1-2) Outputs for connection of TV etc.
5V 1A Connection for adaptor (5 V DC, 1 A).

English

3

Installation

Example

English

1. Connect an HDMI cable (not included) between the output on
the source units (e.g. DVD player or digital receiver) and
the inputs marked “HDMI IN (1-4)” on the HDMI switch.

2. Connect an HDMI cable between the outputs “HDMI OUT (1-2)”
on the HDMI switch and the TV’s HDMI input.
Tip! Memorize which device is connected to which input/output.

3. Connect the included adaptor to the power connection marked
“5V 1A” and insert the adaptor in a wall socket.

4. Push any of the buttons [SELECT OUT] to turn on the device.

4 5

Operating Instructions

When the connections are made and the device is turned on it will
automatically search for a new input with an active device connected.
The indicator light moves from input to input until an active input has
been found and the light for the active input remains lit.

Choose input for HDMI OUT 1

1. Turn on the device (e.g. TV) that you have connected to the output
“HDMI OUT 1” and choose HDMI as input on the TV (See the TV’s
instruction manual).

2. Make sure the device you have connected (DVD player etc.)
is turned on.

3. Push once or several times on [SELECT OUT 1] on the HDMI switch
to choose the input you want to watch. The indicator light in
the top row shows which input is activated for output 1.

• If you turn off the device that is connected to the active input,
the device automatically moves to the search mode until an
active input has been found.

Choose input for HDMI OUT 2

1. Turn on the device (e.g. TV) that you have connected to the output
“HDMI OUT 2” and choose HDMI as input on the TV (See the TV’s
instruction manual).

2. Make sure the device you have connected (DVD player etc.)
is turned on.

3. Push once or several times on [SELECT OUT 2] on the HDMI
switch to choose the input you want to watch. The indicator light
in the bottom row shows which input is activated for output 2.

• If you turn off the device that is connected to the active input,
the device automatically moves to the search mode until an
active input has been found.

English

5

Note!

• When an input is already being used by an output this input
cannot be chosen to the other output.

• Only one output can be activated at a time.

English

Using the remote control

• Push [ ] to turn the switch on and off.

• Choose desired input with the buttons [IN 1] to [IN 4].

Turn off

• Push and hold any of the buttons [SELECT OUT] for approx.
3 seconds and push [ ] once to turn off the HDMI switch.

Care and Maintenance

Use a soft damp cloth to wipe the product. Never use strong
detergents or solvents.

Disposal

When it is time to dispose of the product, dispose of it according to
your local ordinances. If you are unsure please contact
your municipality.

Specifications

Amount of inputs 3 × type A 19-PIN, 1 x type C 19-pin
Number of outlets 2 × type A 19-PIN
Band width, video amplifier 2.25 Gbps
Support for 480i, 480P, 576i, 576p, 720p,1080i,

1080p, VGA, SVGA, SXGA,
(1280×1024), UXGA (1600×1200)

Output Frame Rate 24 Hz – 60 Hz
Power supply 5 V DC 1 A (provided by the

accompanying 230 V AC adaptor)
Battery type, remote control 1 × CR2025 (included)

6 7

Troubleshooting Guide

No indicator lights up. • Check that the adaptor is properly connected and the device

No picture is displayed and
no sound is heard.

The picture is seen but no
sound is heard.

The HDMI switch does not
react on the remote control’s
signals.

It is not possible to choose
input with [SELECT].

is turned on. Push [SELECT] once or [ ] on the remote to
turn on the device.

• Check that all cables are undamaged and properly connected.

• Make sure the DVD movie is not copied since HDMI has

copy protection type HDCP (High-bandwidth Digital
Content Protection).

• Check that the DVD player or TV is set to the DVI position.

• Use only HDMI cables of newer version than 1.1.

• Turn on and off the device once to reactivate the input.

• Check the battery and replace it if necessary.

• Make sure that nothing interferes the remote control’s signals

and the distance is not too big between the remote control
and the HDMI switch.

• Check that the button can be properly pushed in.

• Cut the power by unplugging the adaptor for a short while

and then turn the device on again.

Additional troubleshooting

Problem Solution Explanation

No picture from a computer
with a DVI connector.

Try switching the HDMI-switch
over to the computer’s input
as soon as the computer
has been turned on to get
a picture.

If this solves the problem, it
means that your computer’s
graphic card lacks HPD signal
(Hot Plug Detect) detection
and sends its DDC informa­tion (Display channel Data)
too early (only when it is first
turned on). Some compu­ters with DVI connectors
might not have this detection
feature, which means that
one must employ the above
solution.

The receiving unit such as a TV
or projector sends out an HPD
signal when it is ready to receive
DDC information from the source
unit such as a computer, DVD
player or Blu-ray player.
The units communicate via
the DDC connection. The TV or
projector even informs which
formats (resolutions) it can use so
that the source unit can set itself
up accordingly. The HDMI-switch
sends out an HPD signal every
time the input signal is switched
and is approved by HDMI
Authorized Test Centers. The use
of an HPD signal is a requirement
in accordance with the HDMI
organisation.

English

7

HDMI-växel med fjärrkontroll

Art.nr 38-2878 Modell HD-4200

Läs igenom hela bruksanvisningen före användning och spara den
sedan för framtida bruk. Vi reserverar oss för ev. text- och bildfel
samt ändringar av tekniska data. Vid tekniska problem eller andra
frågor, kontakta vår kundtjänst (se adressuppgifter på baksidan).

Svenska

Säkerhet

• Produkten får endast repareras av kvalificerad servicepersonal.

• Produkten är avsedd endast för inomhusbruk.

• Öppna aldrig höljet, farlig spänning finns oskyddat på vissa

komponenter inuti produktens hölje, kontakt med dessa kan ge
elektrisk chock.

• Placera inte produkten så att den kan falla ner i vatten eller annan
vätska. Ställ aldrig produkten i närheten av föremål som kan
orsaka att vatten eller annan vätska sköljs över produkten, t.ex.
blomvas eller dryck.

• Använd endast för apparaten avsedd eller rekommenderad
batterieliminator.

Förpackningen innehåller

• HDMI-växel

• Fjärrkontroll

• Batterieliminator

• Bruksanvisning

8 9

Knappar och funktioner

Produktens framsida

[SELECT OUT] 1 / 2 Väljer vilken ingång som ska vara aktiverad.
1-4 Indikerar vilken ingång som är aktiverad.
HDMI IN 4 En fjärde ingång för enkel anslutning

av t.ex. tv-spel.

IR Mottagare för fjärrkontrollens signaler.

Produktens baksida

HDMI IN (1-3) Ingångar för anslutning av t.ex. dvd-spelare,

digitalmottagare eller tv-spel.

HDMI OUT (1-2) Utgångar för anslutning till tv etc.
5V 1A Anslutning för batterieliminator (5 V DC, 1 A).

9

Svenska

Installation

Inkopplingsexempel

Svenska

1. Anslut en HDMI-kabel (medföljer ej) mellan utgången på
källenheterna (t.ex. dvd-spelare eller digitalmottagare) och
ingångarna märkt ”HDMI IN (1-4)” på HDMI-växeln.

2. Anslut en HDMI-kabel mellan utgångarna ”HDMI OUT (1-2)” på
HDMI-växeln och teveapparatens HDMI-ingång.
Tips! Memorera vilken apparat du anslutit till vilken
ingång/utgång.

3. Anslut den medföljande batterieliminatorn till
spänningsanslutningen märkt ”5V 1A” och sätt sedan
batterieliminatorn i ett vägguttag.

4. Tryck en gång på någon av knapparna [SELECT OUT] för att slå
på enheten.

10 11