Clarke American Sanders Sander 1600DC Operator's Manual
Sander 1600DC
Operator's Manual / Manual del operador / Manuel de l’utilisateur
MODEL: 07101B
READ THIS BOOK
LEA ESTE MANUAL
EN
ES
FR
LISEZ CE MANUEL
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
American Sanders machine could result in injury to you or to other personnel; damage to the
machine or to other property could occur as well. You must have training in the operation of this
machine before using it. If your operator(s) cannot read this manual, have it explained fully before
attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
Form No. 70408B 7/06 revised 1/14
English
Español
Français
CONTENTS OF THIS BOOK
Operator Safety Instructions ............................................................................................3-4
Machine Introduction ..........................................................................................................4
How To Prepare the Machine for Operation ....................................................................5-7
How to Install the Sandpaper ....................................................................................... 5
Sanding Cuts and Sandpaper ...................................................................................... 5
How to Install the Brush or Pad Driver ......................................................................... 6
How to Adjust the Handle ............................................................................................. 6
How to Install the Skirt ..................................................................................................7
Instructions for Connection to Power Supply & Elect. Ground, 120V ................................. 8
How to Operate the Machine .............................................................................................. 9
How To Start/Stop The Machine ................................................................................... 9
How to Control the Machine .........................................................................................9
How to Use the Lamp ................................................................................................... 9
Maintenance .....................................................................................................................10
Machine Specifi cations ..................................................................................................... 10
revised 9/13
Section II Parts Manual
Main Assembly ............................................................................................................32-33
Base Assembly ............................................................................................................34-35
Handle Assembly ......................................................................................................... 36-37
Lamp Assembly ................................................................................................................38
Gearbox Assembly ........................................................................................................... 39
Wiring Diagrams ............................................................................................................... 40
WARNING!
The Products sold with this Manual contain or may contain chemicals that are known to certain governments (such as the State of
California, as identifi ed in its Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other reproductive harm. In
certain locations (including the State of California) purchasers of these Products that place them in service at an employment job site
or a publicly accessible space are required by regulation to make certain notices, warnings or disclosures regarding the chemicals
that are or may be contained in the Products at or about such work sites. It is the purchaser’s responsibility to know the content of,
and to comply with, any laws and regulations relating to the use of these Products in such environments. The Manufacturer disclaims
any responsibility to advise purchasers of any specifi c requirements that may be applicable to the use of the Products in such
environments
-2 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
revised 9/13
OPERATOR SAFETY INSTRUCTIONS
WARNING AVERTISSEMENT ADVERTENCIA
DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER
statements found on this machine or in this Owner's Manual are ignored or are not
adhered to. Read and observe all DANGER statements found in this Owner's Manual
WARNING means: Injury can occur to you or to other personnel if the WARNING statements found on
CAUTION means: Damage can occur to the machine or to other property if the CAUTION statements
DANGER: Failure to read the Owner's Manual prior to operating or attempting any service or maintenance
procedure to your machine could result in injury to you or to other personnel; damage to the
machine or to other property could occur as well. You must have training in the operation of this
machine before using it. If your operator(s) cannot read English, have this manual explained
fully before attempting to operate this machine.
DANGER: To reduce the risk of fi re, use only commercially available fl oor cleaners and waxes intended for
machine application.
DANGER: Risk of explosion. Floor sanding can result in an explosive mixture of fi ne dust and air. To reduce
risk of explosion, use fl oor sanding machine only in well ventilated area.
DANGER: Dust generated from sanding wood fl oors can spontaneously ignite or explode. Promptly dispose
of any sanding dust in a metal container clear of any combustibles. Do not dispose in a fi re.
DANGER: Operating a machine that is not completely or fully assembled could result in injury or property
damage. Do not operate this machine until it is completely assembled. Inspect the machine carefully before operation.
and on your machine.
your machine or in this Owner's Manual are ignored or are not adhered to. Read and
observe all WARNING statements found in this Owner's Manual and on your machine.
found on your machine or in this Owner's Manual are ignored or are not adhered to.
Read and observe all CAUTION statements found in this Owner's Manual and on
your machine.
DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not disconnect-
ed from the power source. Disconnect the power supply before attempting any maintenance or
service. Always remove the electrical plug from the electrical outlet before changing the brush, pad
or other attachment and before leaving the machine.
DANGER: Using a machine with a damaged power cord could result in an electrocution. Do not use the ma-
chine if the power cord is damaged. Do not use the electrical cord to move the machine.
WARNING: Maintenance and repairs performed by unauthorized personnel could result in damage or injury.
Maintenance and repairs must be performed by authorized personnel only. Keep all fasteners tight.
Keep adjustments according to specifi cations.
WARNING: Electrical components of this machine can "short-out" if exposed to water or moisture. Keep the
electrical components of the machine dry. Wipe the machine down after each use. For storage,
keep the machine in a dry building.
WARNING: Always use a three-wire electrical system connected to the electrical ground. For maximum protec-
tion against electric shock, use a circuit that is protected by a ground fault interrupter. Consult your
electrical contractor.
WARNING: To prevent damage to the power cord, do not let the brush, pad, pad driver or wheels touch the
power cord when the machine is running. Always lift the cord over the machine. Do not pull the
power cord to move the machine.
Clarke® American Sanders Operator's Manual - Sander 1600DC FORM NO. 70408B - 3 -
revised 9/13
OPERATOR SAFETY INSTRUCTIONS (cont.)
WARNING: Operating a machine without observing all labels and instructional information could result in injury
or damage. Read all machine labels before attempting to operate. Make sure all of the labels and
instructional information are attached or fastened to the machine. Get replacement labels and
decals from your authorized distributor.
WARNING: Use of this machine as a step or furniture could result in injury or damage. Do not use this
machine as a step or furniture. Do not ride on this machine.
WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this
machine.
WARNING: Injury can occur if protective clothing or equipment is not used while sanding. Always wear safety
goggles, protective clothing, and dust mask while sanding.
WARNING: Injury to operator or bystanders could occur if an abrupt change in fl oor surface texture is
encountered when using this machine. Abrupt change in fl oor surface texture can cause a
sudden pulling motion by this machine. This sudden pulling motion can result in loss of
control of the machine which could injure the operator or bystanders. Avoid motions that
could cause machine to cross from a smooth fl oor surface to a carpeted or rough texture
fl oor surface Avoid motions that could allow the machine to come in contact with low
obstacles, such as fl oor electrical outlets, door stops or entry molding, etc.
WARNING: Water solutions or cleaning materials used with this type of machine can leave wet areas
on the fl oor surface. These areas can cause a dangerous condition for the operator or
other persons. Always put CAUTION signs near the area being cleaned.
WARNING: Any alterations or modifi cations of this machine could result in damage to the machine or
injury to the operator or other bystanders. Alterations or modifi cations not authorized by
the manufacturer voids any and all warranties and liabilities.
CAUTION: The machine is heavy. Get assistance before attempting to transport or move it.
CAUTION: Use of this machine to clean carpet could cause damage to carpet and injury to operator or by-
standers. Do not use this machine to clean carpet.
MACHINE INTRODUCTION
The Sander 1600DC
The Sander 1600DC is a fl oor sanding machine. It can also be used for polishing, spraying, buffi ng and stripping. The
machine can be used on wood, vinyl, terrazzo or cement fl oors.
-4 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
revised 9/13
HOW TO PREPARE THE MACHINE FOR OPERATION
WARNING: Always remove the electrical plug from the
electrical outlet before installing or changing the sandpaper.
How To Install The Sandpaper
To install the sandpaper, follow this
procedure:
1. Put the handle in the vertical position.
2. Lock the handle. To lock the handle, push the locking lever down.
See fi gure 1.
Figure 1
Figure 2
3. Tilt the machine backward until the handle is on the fl oor.
4. Put one foot on each side of the machine.
5. Using a 7/8 wrench, remove the nut and the washer that hold the
paper holder. See fi gure 2.
6. Put the sandpaper on the sanding pad.
7. Put the paper holder in position. See fi gure 3.
8. Install the washer and the nut that hold the paper holder.
Sanding Cuts and Sandpaper
Initial Cut
The purpose of the initial cut is to remove old fi nish and gross im-
perfections on the fl oor surface. A coarse abrasive should be used.
If glazing, loading, or burning takes place immediately into an initial
cut, select a coarser abrasive. If this should occur during an initial cut,
the abrasive has dulled and must be replaced.
Final Cuts
The purpose of a fi nishing cut is to remove the scratches produced
during the initial cut. Use a fi ne (60-80 grit) grain abrasive.
If the surface remains rough after a fi nishing cut, it may be necessary
to use an even fi ner grain of abrasive
(80-100 grit). Care should be taken in selecting the grit size of the
abrasive. A very fi ne grain will close the pores on a wood fl oor making
admission of a stain diffi cult.
Figure 3
Clarke® American Sanders Operator's Manual - Sander 1600DC FORM NO. 70408B - 5 -
revised 9/13
HOW TO PREPARE THE MACHINE FOR OPERATION
WARNING: Always remove the electrical plug from the
electrical outlet before installing or changing the pad or brush.
How To Install The Brush Or Pad Driver
To install the brush or pad driver, follow this
procedure:
1. Put the handle in the vertical position.
2. To lock the handle, push the locking lever down.See fi gure 4.
Figure 4
Figure 5
3. Tilt the machine backward until the handle is on the fl oor. See fi gure
5.
4. Put one foot on each side of the machine. See fi gure 5.
5. Align the lugs (1) on the locking plate into the pad driver adapter
openings (2). See fi gure 6.
6. To lock the brush or pad into position, turn the brush or pad driver
clockwise.
7. Turn the brush or pad counterclockwise to unlock and remove the
brush.
8. Lift the machine to the vertical position.
NOTE: To prevent damage to the brush or pad driver, remove the
accessory while not in use. Keep the brush in a cool, dry place.
How To Adjust The Handle
To adjust the handle, follow this procedure:
1. The locking lever is on the lower part of the handle tube. Use your
foot to lift the lever. See fi gure 3.
2. Lower the handle to the best operating position.
NOTE: For the best operating position, keep your back straight,
bend only your arms.
3. Using your foot, push the locking lever down.
Figure 6
1. The lugs.
4. Hold the handle against your body for the best control.
2. The drive adpater openings.
-6 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
revised 9/13
Figure 7
HOW TO PREPARE THE MACHINE FOR OPERATION
How to Install the Dust Control Skirt
To install the skirt, follow this procedure:
1. Wrap the skirt around the bumper such that the draw string can be
inserted into the recess of the bumper. See fi gure 7.
2. Orient the brush fastening strap at the rear of the machine to prevent
scratching surfaces.
3. Tighten and tie the string on the skirt into a bow knot so it can later
be untied for removal of the skirt.
4. Twist the ends of the string (see fi gure 7) and insert them into the
recess of the bumper as shown in fi gure 8.
NOTE: The skirt should be stored fl at on the fl oor either on or off
of the machine.
Figure 8
Clarke® American Sanders Operator's Manual - Sander 1600DC FORM NO. 70408B - 7 -
revised 9/13
120 VOLT MACHINES
Instructions for connection to the power supply and the electrical ground.
This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current
to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and grounding
plug. The plug must be inserted into an appropriate oulet that is properly installed and grounded in accordance with all local codes and
ordinances.
WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with
a qualifi ed electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the
plug provided with the product - if it will not fi t the outlet, have a proper outlet installed by a qualifi ed
electrician.
This product is for use on a nominal 120 volt circuit and has a grounding attachment plug that looks like the plug illustrated in Fig. 9. Make
sure that the product is connected to an outlet having the same confi guration as the plug. No adaptor should be used with this product.
WARNING: To prevent possible electric shock, protect the machine from rain. Keep the machine in a dry building.
WARNING: To prevent possible electric shock, always use a 3-wire electrical system connected to the electrical ground.
For maximum protection against electrical shock, use a circuit that is protected by a ground fault circuit interrupter. Consult
your electrical contractor.
WARNING: Do not cut, remove or break the ground pin. If the outlet does not fi t the plug, consult your electrical con-
tractor.
WARNING: Have worn, cut or damaged cords replaced by an authorized service person.
EXTENSION CORDS
Use only an approved extension cord with three conductors, a plug with three terminals, and a connector body with three holes. The machine has a power cord with wire size 14 AWG (AWG means American Wire Gauge).
WARNING: If you use an extension cord, use an extension cord with minimum wire size 12 AWG. Do not use an extension
cord longer than 50 feet. Do not join two extension cords.
Grounded
Outlet
Grounded
Outlet
Grounding
Box
Pin
(United States, Mexico and Canada)
Figure 9
-8 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
revised 9/13
HOW TO OPERATE THE MACHINE
How To Start/Stop The Machine
WARNING: Never start machine when the handle is
in the vertical position.
The switch to start and stop the machine is activated
by the interlock switch (Fig. 10) and the levers (Fig 10A) under the
handle grips.
Figure 10
Figure 10A
To start the machine, follow this procedure:
1. Lower the handle
2. Lock the handle in the best position for operation.
NOTE: Make sure you hold the handle with both hands.
3. Push the interlock switch (Fig. 10), and apply pressure to the
levers (Fig. 10A).
How To Control The Machine
NOTE: Sanding operations create higher torque conditions than
normal fl oor polishing. Make sure you fi rmly grip the handle
with both hands.
The side to side movement of the machine is controlled by raising
the handle and pressing down on the handle. To move the machine
to the left, press down on the handle slightly. To move the machine
to the right, raise the handle slightly.
How To Use The Lamp
To turn the lamp on:
1. Plug the lamp into the machine.
2. Plug the machine into the power source.
To position the lamp:
1. Loosen the knob on the top of the motor (see fi gure 11) and pivot
the lamp to the desired position.
2. Retighten the knob.
Figure 11
To remove the lamp:
3. Unplug the cord at the bottom of the lamp.
4. Loosen and remove the mounting knob (see fi gure 11) on top of
the motor.
5. Remove the lamp and reattach the mounting knob.
Clarke® American Sanders Operator's Manual - Sander 1600DC FORM NO. 70408B - 9 -
revised 9/13
MAINTENANCE
WARNING: Maintenance must be done by authorized personnel only.
CAUTION:
Maintenance Instructions
Return the machine to a Clarke American Sanders Authorized Service Location every 12 months for maintenance inspections.
Switches
WARNING: All electrical repairs must be done by authorized personnel only. The machine must be tested after electrical
repairs to make sure it is safe to operate. Disconnect the electrical plug from the electrical outlet before doing any electrical
repairs.
The start and stop switch has an interlock which prevents the contacts from being closed. If any part of the switch is not operating,
replace the part. If any part of the electrical system of the machine is not operating or is damaged, replace the part. Make sure all
connections are tight. Return the machine to the Clarke American Sanders Service Branch or a Clarke American Sanders Authorized
Service Center for electrical repairs or testing.
Maintenance Of The Motor
Induction type motors do not require motor brushes.
Keep all adjustments according to specifi cations.
If repairs to the gear unit or motor are needed, do not disassemble the gears and motor. Return the machine to the nearest Clarke
American Sanders Service Branch or Clarke American Sanders Authorized Service Center.
For safe operation, and longer life to your Clarke American Sanders product, use only Clarke American Sanders parts.
NOTE: The grease (503802) for the gear box needs to be changed every year. The Sander 1600 and 1600DC require 8 oz. of grease.
Machine Specifi cations
Model Sander 1600DC
Code Number 07101B
Voltage (Volts) 120
Frequency (Hz) 60
Current (Amps) 14
Power (hp) 1.5
Pad Diameter 16.0
Pad Speed (rpm) 175
Cord Length (feet) 50
Weight (pounds) 121
-10 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
Clarke® American Sanders Operator's Manual - Sander 1600DC FORM NO. 70408B - 11 -
revised 9/13
LIBRO DE INSTRUCCIONES
LEA ESTE LIBRO
CUIDADO: Lea el Libro de Instrucciones antes de usar este aparato.
Contiene información importante para el uso y funcionamiento correcto y seguro de la máquina. Lea este libro completamente antes de arrancar la máquina o hacer cualquier operación de mantenimiento. Si non sigue las instrucciones, corre
el peligro de herirse o causar lesiones al personal, o causar daños importantes a la máquina o a su entorno. Antes de
usar la máquina, es indispensable seguir una formación. Si Usted (o el operador) no habla español, solicite (o proporciónele) todas las informaciones necesarias. El libro está traducido en otros idiomas.
Todas las indicaciones de dirección dadas en este libro están dadas desde la posición del operador en la parte de atrás
de la máquina.
Puede Ud. conseguir libros suplementarios dirigiéndose a su distribuidor Clarke American Sandeers.
INDICE
Instrucciones de seguridad para el operador ............................................................................. 13-14
Presentación de la máquina ............................................................................................................ 14
Preparación de la máquina para trabajar ................................................................................... 15-17
Cómo instalar el papel abrasivo ............................................................................................... 15
Fases de pulimentado y tipo de papel abrasivo ....................................................................... 15
Instalación del cepillo o del portadisco ..................................................................................... 16
Reglaje de la tobera ................................................................................................................. 16
Cómo instalar la falda ............................................................................................................... 17
Instrucciones para la conexión con la red 120 V ............................................................................. 18
Funcionamiento de la máquina ....................................................................................................... 19
Arranque y parada .................................................................................................................... 19
Dominio del desplazamiento de la máquina ............................................................................. 19
Cómo utilizar la lámpara ........................................................................................................... 19
Mantenimiento ................................................................................................................................. 20
Especifi caciones de la puilidora Sander .......................................................................................... 20
Sección II Manual de piezas ........................................................................32-40
ADVERTENCIA:
Los Productos a la venta en este Manual contienen, o pueden contener, productos químicos reconocidos por algunos gobiernos
(como el Estado de California, según lo indica en su Proposición 65, Ley de Advertencia Regulatoria) como causantes de cáncer,
defectos de nacimiento u otros daños reproductivos. En algunas jurisdicciones (incluido el Estado de California), los compradores
de estos Productos que los coloquen en servicio en un emplazamiento laboral o en un espacio de acceso público tienen la
obligación regulatoria de realizar determinados avisos, advertencias o divulgaciones respecto de los productos químicos contenidos
o posiblemente contenidos en los Productos utilizados en tal lugar. Es la responsabilidad del comprador conocer y cumplir con
todas las leyes y reglamentaciones relacionadas con el uso de estos Productos en tales entornos. El Fabricante niega toda
responsabilidad de informar a los compradores sobre requisitos específi cos que pueden regir el uso de los Productos en tales
entornos.
-12 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
revised 9/13
INSTRUCCIONES PARA LA SEGURIDAD DEL OPERADOR
WARNING AVERTISSEMENT ¡ AVISO !
¡ PELIGRO ! : Si no sigue la indicación PELIGRO, se pueden causar lesiones graves, incluso mortales.
Lea y siga todas las indicaciones PELIGRO que se encuentran en el libro y en la máquina.
¡ AVISO ! : Si no sigue la indicación AVISO, se pueden causar lesiones sea al operador sea a otro
personal y/o daños materiales. Lea y siga todas las indicaciones AVISO que se encuentran
en el libro y en la máquina.
¡ CUIDADO ! : Si no sigue la indicación CUIDADO, se puede estropear la máquina o causar daños materi-
ales. Lea y siga las indicaciones CUIDADO que se encuentran en el libro y en la máquina.
¡ CUIDADO ! Siempre lea este libro de instrucciones antes de arrancar la máquina o hacer un man-
tenimiento. A falta de esta precaución, corre el peligro de herirse o causar lesiones a colegas ; podría Ud. también causar daños a la máquina o a su lugar de trabajo. Se debe
aprender el manejo de esta máquina antes de usarla. Si Usted (o su plantilla) no conoce
el español, se ruega dejarse explicar todo el libro antes de usar la máquina.
¡ CUIDADO ! Para evitar un peligro de incendio, use sólo productos de limpieza y cera para el suelo
especialmente concebidos para máquinas.
¡ CUIDADO ! Peligro de explosión : mientras apomaza un parqué, una mezcla explosiva de partículas
de polvo y aire puede formarse. Para reducir el peligro de explosión, use la máquina
sólo en locales perfectamente ventilados.
¡ CUIDADO ! El plovo que se crea al pulimentar los suelos de madera puede causar un incendio o una
explosión de manera accidental. Deseche inmediatamente el polvo de haber pulimentado en un contenedor de metal limpio y sin material combustible. No lo vierta a una
fuente de calor.
¡ CUIDADO ! Si usa una máquina antes de que esté completamente montada, corre el peligro de
herirse o causar daños materiales. No opere la máquina antes de que esté completamente montada. Compruebe cuidadosamente el estado de la máquina antes de cada
utilización.
¡ CUIDADO ! Si efectúa un mantenimiento o una reparación sin desconectar la máquina, hay un ries-
go de electrocución. Desconecte el enchufe de la caja conectada con la red antes de
empezar el mantenimiento o la reparación. Siempre desconecte el enchufe de la caja
de enchufe conectada con la red antes de cambiar el cepillo, el disco o cualquier otro
accesorio y si deja la máquina sin vigilarla.
¡ CUIDADO ! Si opera la máquina con un cable de alimentación estropeado, se puede causar una
electrocución. No use nunca la máquina si el cable de alimentación está estropeado.
No tire de la máquina usando el cable eléctrico.
¡ AVISO ! Una reparación o un mantenimiento efectuado por personas no cualifi cadas puede cau-
sar lesiones y/o daños materiales. Todas las operaciones de mantenimiento o de reparación de la máquina deben ser efectuadas por técnicos cualifi cados. Compruebe que
las fi jaciones están correctamente apretadas. Haga reglajes conforme a las indicaciones
dadas en el libro.
Clarke® American Sanders Operator's Manual - Sander 1600DC FORM NO. 70408B - 13 -
revised 9/13
¡ AVISO ! Hay un riesgo de cortocircuito si los componentes eléctricos de una máquina están ex-
puestos a la humedad o son mojados. Procure que los componentes eléctricos sean
siempre secos. Seque cuidadosamente la máquina después de cada utilización. Guarde
la máquina en un local seco.
¡ AVISO ! Use siempre un cable con tres conductores puestos a tierra. Para una protección óptima,
conecte la máquina con una caja de enchufe conectada con la red que tiene un diferencial.
Si tiene alguna duda, sírvase acudir a un eléctrico cualifi cado.
¡ AVISO ! Para evitar daños al cable de alimentación, procure que el cepillo, el disco, el portadisco o
las ruedas no toquen el cable, cuando la máquina funciona. Levante siempre el cable por
encima de la máquina. No tire de la máquina para acercar la máquina.
¡ AVISO ! Si usa la máquina sin respetar todas las instrucciones escritas en los adhesivos y los carte-
les, corre el peligro de causar lesiones y daños materiales. Lea todas las indicaciones escritas en la máquina antes de la primera utilización. Compruebe que todos los adhesivos
y las instrucciones estén colocados en los sitios previstos. Si es preciso, haga un nuevo
pedido a su distribuidor Clarke American Sanders.
¡ AVISO ! No use la máquina como escabel o mueble. Corre el peligro de causar lesiones o daños
materiales. No use la máquina como medio de transporte.
¡ AVISO ! Para evitar herirse, sírvase mantener une distancia de seguridad sufi ciente entre las partes
móviles de la máquina y sus manos o sus pies. No lleve ropas holgadas.
¡ AVISO ! Si no utiliza las ropas de protección o el equipamiento adecuado para realizar las opera-
ciones de pulimentado podría sufrir lesiones. Póngase siempre las gafas, las ropas de
protección y la mascarilla para el polvo cuando esté pulimentado.
¡ AVISO ! Una modifi cación brusca de la textura del suelo puede causar un sobresalto de la máquina
de la cual el operador pierde momentáneamente el dominio. Eso puede causar lesiones
al operador o a otras personas encontrándose cerca. Procure que la máquina no pase de
una superfi cie lisa a una alfombra o una superfi cie más rugosa. Procure que la máquina
no esté en contacto con cajas de enchufe colocadas en el suelo, topes de puerta o casquillos, etc.
¡ AVISO ! Las soluciones acuosas o los productos de limpieza usados con esta máquina pueden
dejar zonas húmedas en el suelo, que pueden ser causa de peligro para el operador u
otras personas. Ponga siempre señales de PRECAUCION cerca de la superfi cie que está
limpiando.
¡ATENCIÔN ! Esta máquina pesa. Transpórtela o desplácela con ayuda de otra persona.
¡ATENCIÓN ! Si se emplea la máquina para limpiar alfombras podría dañar la alfombra o causar lesiones
al operador o a las personas que están alrededor. No utilice esta máquina para limpiar
alfombras.
PRESENTACION DE LA MAQUINA
Sander 1600DC
Sander 1600DC es una máquina para pulir pisos. También puede ser utilizada para lustrar, pulverizar, sacar
brillo y decapar. La máquina puede ser utilizada en pisos de madera, vinilo, terrazzo o cemento.
-14 - FORM NO. 70408B Clarke® American Sanders Operator's Manual - Sander 1600DC
Loading...