Page 1
Diamond Core Drills
CLARKE core drills are vibrationless when used as directed.
Core drills are used to form holes in, brick, concrete blocks, aerated blocks, asphalt, Cotswold
stone and limestone.
A heavy duty drill with a ½ chuck, low speed and high torque must be used with diamond core
drills.
NEVER USE HAMMER ACTION WITH DIAMOND CORE DRILLS
NOTE
All core drills larger than 28mm must be used with an arbor and pilot/guide drill, these
are sold separately and can be purchased from your nearest Clarke dealer
Core Drills In The Clarke Range
Model Dia Length
SCD28 28mm 300mm
SCD38 38mm 150mm
SCD52 52mm 150mm
SCD78 78mm 150mm
SCD107 107mm 150mm
SCD117 117mm 150mm
SCD127 127mm 150mm
CLARKE GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for
the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not effect your statutory rights.
0303
Page 2
PARTS & SERVICE
SAFETY PRECAUTIONS
For your own safety and that of others around you, please read and observe
these safety instructions.
1.
ALWAYS
and become familiar with the entire operating manual.
2.
ALWAYS
3.
ALWAYS
do not have impact resistant lenses, they are not safety glasses.
4.
ALWAYS
5.
ALWAYS
accessories.
6.
ALWAYS
that it will operate properly, and perform its intended function. Check for alignment of moving parts,
breakage of parts, mountings, and any other condition that may affect the machines operation. Any
damage should be properly repaired or the part replaced. If in doubt,
your local dealer.
7.
ALWAYS
Learn the machines applications, limitations and the specific potential hazards peculiar to it. Read
wear good quality industrial gloves.
wear safety goggles, manufactured to the latest European Safety Standards. Everyday eyeglasses
wear a suitable dust mask.
disconnect the tool/machine from the power supply before servicing and when changing
check for damage. Before using the machine, any damaged part, should be checked to ensure
DO NOT
keep work area clean. Cluttered areas and benches invite accidents.
use the machine. Consult
8.
ALWAYS
Ensure that lighting is placed so that you will not be working in your own shadow.
9.
ALWAYS
operating the machine.
10.
ALWAYS
Follow maintenance instructions.
11.
ALWAYS
disconnect it from the power supply .
11.
ALWAYS
12.
ALWAYS
caused by carelessness due to familiarity.
13.
ALWAYS
soled footwear. keep floor clear of oil, scrap wood, etc.
ensure that adequate lighting is available. A minimum intensity of 300 lux should be provided.
keep children away. All visitors should be kept a safe distance from the work area, especially whilst
maintain machine in top condition. Keep tools/machines clean for the best and safest performance.
handle with extreme care do not carry the tool/machine by its electric cable, or yank the cable to
ensure the switch is off before plugging in to mains. Av oid accidental starting.
concentrate on the job in hand, no matter how trivial it may seem. Be aware that accidents are
keep your proper footing and balance at all times dont overreach. For best footing, wear rubber
Directions For Use
1. Insert core drill into chuck and tighten securely.
2. With drill set to a reasonably slow speed, plug in and switch ON.
3. Slowly offer core drill to wall etc to be drilled until it touches , using a steady pressure, push drill into surface,DO NOT
FORCE, allow the drill to do the work. It may be necessary to adjust the speed to suit the size of drill and the material
being cut.
AS A GENERAL GUIDE ONLY, the larger the drill, the slower the speed required, also the harder the material being cut,
the slower the speed.
4. To ensure the core drill doesnt bind, occasionally withdraw it from the hole whilst it is still turning to clear any waste,
keep repeating this process until the hole is finished.
5. When finished turn the drill OFF and unplug from the main electric supply.
6. Remove core dril and store safely for later use.
!!! CAUTION !!!
When using core drills, ensure a firm grip at all times on the machine to prevent the drill being snatched from your hands in
the event of a jam. Jaming can be caused for various reasons, such as small pieces of brick etc breaking off an wedging
the core drill in the hole.
Please note that the details and specifications contained herein are correct at the time of going to print. However CLARKE International reserve the right to
change specifications at any time without prior notice. Always consult the machines data plate
Loading...