Clarke Raider 15/1000, 2242205 User guide

100L AIR COMPRESSOR

MODEL NO: RAIDER 15/1000

PART NO: 2242205

OPERATION & MAINTENANCE

INSTRUCTIONS

LS0620 - ISS 4ORIGINAL INSTRUCTIONS

INTRODUCTION

Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the
obligation to deal with the WEEE in accordance with the WEEE
regulations in relation to the treatment, recycling & recovery and
environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general
household waste. It must be disposed of according to the laws governing
Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal
facility.

2

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SAFETY PRECAUTIONS

Before using your compressor it is in your own interest to read and pay attention
to the following safety rules.

1. Compressed air is dangerous. Do not point a jet of air at persons or animals, and do
not discharge compressed air against the skin.

2. DO NOT operate your compressor with the guard removed.

3. Repairs must only be carried out by a qualified engineer. If problems occur, contact
your dealer.

4. Before carrying out any maintenance, make sure that the pressure is released from
the air reservoir, and that the compressor is disconnected from the electrical supply.

5. DO NOT leave pressure in the receiver overnight, or when transporting.

6. DO NOT adjust, or tamper with the safety valves. The maximum pressure is factory
set, and clearly marked on the compressor.

7. DO NOT operate in wet or damp conditions. Keep the compressor dry at all times.
Similarly, clean air will allow the compressor to work efficiently. Do not use in dusty or
otherwise dirty locations.

8. Some of the metal parts can become quite hot during operation. Do not to touch
these until the compressor has cooled down.

9. Always set the pressure regulator to the recommended setting for the tool.

10. When spraying flammable materials e.g. cellulose paint, ensure that there is
sufficient airflow and keep clear of any source of ignition.

11. Before spraying any material always consult paint manufacturers instructions for
safety and usage.

12. Protect yourself. Goggles will protect your eyes from flying particles. Face masks will
protect you against paint spray and fumes.

13. Do not apply strain to electrical cables and make sure that air hoses are not kinked
or wrapped around the compressor.

14. When disconnecting air hoses or other equipment from your compressor, make sure
that the air supply is turned off at the outlet and vent all pressurised air from within
the reservoir and other equipment attached to it.

15. Make sure that children and animals are kept well away from the compressor and
any equipment attached to it.

16. Make sure that all individuals using the compressor have had the necessary training
and have read and fully understand these operating instructions.

17. Make sure that any equipment or tool used in conjunction with your compressor, has
a safe working pressure exceeding that of the compressor.

18. Be careful when transporting the compressor to prevent tipping over

19. Permanently installed systems must be installed by a competent engineer.

20. These compressors produce noise levels in excess of 70dB(A). Persons working near
the compressor must be supplied with ear protection.

3

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SAFETY SYMBOLS

Read this instruction booklet carefully before positioning,
operating or adjusting the compressor.

Risk of electric shock. The compressor must be
disconnected from the mains supply before removing any
covers. Do not use in a damp environment.

Risk of accidental start-up. The compressor could start
automatically in the event of a power cut and subsequent
reset. Do not carry the compressor while it is connected to
the power source, or when the tank is filled with
compressed air.

This compressor contains surfaces which may reach a high
temperature during operation. Never operate with the
motor housing removed.

Wear a safety goggles and ear protectors when using this
compressor

This compressor produces a high sound level during
operation. Ear protection should be worn.

4

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

ELECTRICAL CONNECTIONS

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yel low)

WARNING! Read these electrical safety
before connecting the product to the mains supply.

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply
through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or
because of damage, it must be removed and a replacement fitted, following
the wiring instructions shown below. The old plug must be discarded safely, as
insertion into a power socket could cause an electrical hazard.

WARNING! The wires in the power cable of this product are
coloured in accordance with the following code:
Blue = Neutral Brown = Live Yellow and Green = Earth

If the colours of the wires in the power cable do not agree with the markings
on the plug.

• The BLUE wire must be

connected to the
terminal which is
marked N or coloured
back.

• The BROWN wire must

be connected to the
terminal which is
marked L or coloured
red.

• The YELLOW AND

GREEN wire must be
connected to the terminal which is marked E or or coloured green.

We strongly recommend that this machine is connected to the mains supply
through a Residual Current Device (RCD)

If you are not sure, consult a qualified electrician. DO NOT try to do any
repairs.

instructions thoroughly

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

5

ASSEMBLY

ATTACH THE WHEELS

Use a spanner to attach the wheels
to the compressor.

Use the washers and spring washer in
the positions shown.

ATTACH THE SUPPORT FEET

Insert the support feet into the
position shown.

FIT THE AIR FILTER

1. If fitted, remove the travel plug.

2.

Screw the air filter into position.

• The air filter must be hand tight
only.

6

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

FIT THE HANDLE

1. Slide the handle into the position
shown and secure in place using
the fixing

s provided.

FIT THE OIL FILLER CAP

1. Remove the travel plug.

2. Insert the oil filler cap.

MOVING THE AIR COMPRESSOR

CAUTION: TO PREVENT INJURY, GET ASSISTANCE WHEN LIFTING THIS
COMPRESSOR.

• Stop the compressor and disconnect it from the power supply

before you move it.

• Always use the handle.

• To prevent damage, do not lift by (or put strain on) valves or hoses.

7

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

BEFORE USE

Before connecting your compressor to the power supply, check the following:-

• Set the ON/OFF switch to the
OFF position (pushed down).

• Make sure that the compressor
is on level ground.

• Make sure that the supply
voltage matches the voltage
shown on the data label.

CHECK THE OIL LEVEL

1. Make sure that the oil level is half
way up the oil sight glass.

2.

If not, remove the oil cap and
add oil to the reservoir.

• Only use SAE30 compressor oil,

available from your Clarke
dealer Part No. 3050801

8

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

OPERATION

If the compressor has not been used for more then 24 hours, open the drain
valve (on the bottom of the reservoir) and drain any condensate which has
collected. See page 11.

ATTACHING AIR TOOLS

WARNING: BEFORE CONNECTING AIR TOOLS, MAKE SURE THAT YOU
READ THE INSTRUCTIONS SUPPLIED WITH THE TOOL, ALSO ENSURE THAT
THE TOOL IS SUITABLE FOR USE WITH THE COMPRESSOR AND HOSE
SPECIFICATIONS.

1. Attach the air hose to the ¼" BSP
outlet valve.

2. Attach the air tool to the other
end of the air hose.

3. Turn the outlet valve handle to the
on position.

NOTE: Th

e outlet valve is shown
without the air hose fitted for
clarity.

TURNING THE COMPRESSOR ON

1. Plug the compressor into the
power supply.

2. Lift the On/Off button.

• The compressor will operate

until the reservoir is fully
pressurised. It will then shut
down.

• The compressor will start up

again when the pressure in the
reservoir decreases.

9

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SET THE OUTLET PRESSURE

When viewed from the front, the left hand outlet valve is adjustable. The right
hand outlet valve will only supply the full reservoir pressure and is not
adjustable.

1. Use the pressure regulator to set
the output pressure of the left
hand outlet valve.

• Turn clockwise to increase the

pressu

re.

• Turn counterclockwise to

decrease the pressure.

GAUGES

1. The reservoir pressure gauge
shows the current pressure in the
reservoir

2. The outlet pressure gauge shows
the ‘user
can be adjusted as shown above.

.

set’ outlet pressure. This

REMOVING TOOLS FROM THE AIR HOSE

WARNING: ALWAYS SET THE PRESSURE REGULATOR TO ZERO BEFORE YOU
REMOVE OR REPLACE A TOOL.

1. Push down on the On/Off button
to stop the compressor.

10

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

2. Turn the outlet valve handle to the
off position.

3. Operate the tool to depressurise
th

e air hose.

4. Disconnect the tool from the
hose.

TURNING THE COMPRESSOR OFF

1. Follow steps 1-3 in “Removing Tools
From The Air Hose” above.

2. Disconnect the compressor from
the po

wer supply.

3. Slowly open one of the outlet
valves to depr

• You will hear a hissing sound as

the reservoir depressurises.

• Do not leave the compressor

unattended if the reservoir is pressurised.

essurise the reservoir.

DRAINING THE RESERVOIR

CAUTION: YOU MUST DRAIN THE RESERVOIR AFTER EACH DAYS USE AND
BEFORE YOU PUT YOUR COMPRESSOR INTO STORAGE

1. Turn the compressor off and
disconnect from the power

ply.

sup

2. Put a container below the drain
valve to

3. Open the drain valve slowly.

• Condensation will drain from

4. Close the drain valve when the
reservoir has fully drained.

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

collect the condensate.

the reservoir

.

11

RESET BUTTON

This compressor has a thermal
overload device.

If the motor gets too hot, the thermal
overload device cuts the power
which prevents damage to the motor.

If the thermal overload device
operates, let the motor cool down for
5 minutes and push the reset button.

If you start the compressor and the
overload cutout operates again, stop
the compressor and disconnect from the power supply and have your
compressor examined by a qualified service agent.

12

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

MAINTENANCE

DRAIN THE RESERVOIR (DAILY)

After use, always open the drain valve to make sure that any condensate is
drained off.

CLEAN THE AIR FILTER (MONTHLY)

The air filter must be examined monthly, more often in dusty conditions,

1.

Remove the filter from the
compressor.

Remove the filter cover from the

2.
filter.

3.

Remove the filter from the filter
cover.

4. Clean the sponge and the filter
cover using a soft brush.

• If necessary, the filter can be

car

efully cleaned in warm

soapy water.

• Rinse and let the filter dry

completely before refitting.

5. Make sure that the filter and filter cover are

• If the filter is damaged, you must replace it.

13

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

replaced into position.

CHECK THE NON-RETURN VALVE (EVERY 6 MONTHS)

If the reservoir pressure decreases for no apparent reason, it is possible that the
non-return valve is leaking. To check,

1. Make sure that the reservoir is not
under pressure and the

essor is switched OFF.

compr

2. Examine the non-return valve,
an

d replace the gasket and valve

if necessary.

SPECIFICATIONS

Max Pressure 8 Bar

Vo lt ag e 230 VAC (50 Hz)

Air Displacement 14.5 CFM

Receiver Capacity 100 L

Fuse Rating 13 A

Dimensions (L x W x H) 1040 x 440 x 790 mm

Guaranteed Sound Power Level 93 dB(A)

Weight 54 kg

Please note that the details and specifications contained herein, are correct at
the time of going to print. We reserve the right to change specifications at any
time without prior notice.

14

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

TROUBLESHOOTING

CAUTION: DO NOT TRY TO REPAIR OR ADJUST THIS COMPRESSOR IF YOU
ARE UNCERTAIN. IF YOU HAVE ANY QUERIES, CONTACT YOUR DEALER.

PROBLEM PROBABLE CAUSE REMEDY

The compressor
has stoppe
does not start.

The compressor

es not reach

do
the set pressure
and overheats
easily.

Compressor does

t start.

no

Air leaking from

non-return

the
valve when the
compressor is not
running.

Air pressure from
the re
not adjust.

The compressor is

y noisy and

ver
makes a metallic
knocking sound.

d and

gulator will

Bad electrical connections. 1. Check electrical connections.

2. Clean and tighten if necessary.

Overload cutout switch has
trippe

d.

Motor windings burnt out. 1. Contact your Clarke dealer for

Compressor head gasket
blown or valve br

The reservoir has already fully
pressurised.

Faulty non-return valve. 1. Drain receiver completely of

The diaphragm within the
regulator body is broken.

Compressor damaged and

eeds overhaul.

n

oken.

1. Switch off and wait approx 5
minutes.

2. Press the reset button and
swi

a replacemen

1. Return the machine to your
nearest service agent.

1. Open drain valve to expel air.
Compressor should start again
when pressure reduces.

air

2. Remove the valve end plug,

3. Carefully clean the valve seat
an

4. Reassemble.

1. Replace regulator

1. Return the machine to your
nearest service agent.

tch on again.

t motor.

.

d the gasket

15

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

EXPLODED DIAGRAM

16

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

PARTS LIST

NO DESCRIPTION

1 Boltm6x55

2 Cylinder Head

3 Cylinder Seals

4 Valve Plate

5 Valve Plate Gasket

6 Valv e C l a c k

7 Pin

8 Cylinder

9 Cylinder Gasket

10 Piston Ring

11 Oil Ring

12 Piston

13 Piston Pin

14 Circlip

15 Conncting Rod

16 Rubber Gasket

17 Breather

18 Crank Case Cover

19 Bolt M6x16

20 Oil Leveler

21 Bolt M8x20

22 O Ring

23 Crank

24 Bolt M8x30

25 Crank Case

26 Bolt M6x30

27 Sealing Ring

28 Brearing 6205

29 Start Capacitor

30 Nut M8

31 Capacitor

32 Crankcase Support

33 Bolt M8x25

34 Elbow

35 Pipe

NO DESCRIPTION NO DESCRIPTION

36 3 Way @elbow

37 Air Filter

38 Protector

39 Bolt M5x8

40 Junction Box

41 Stator

42 Rotor

43 Brearing 6205

44 Washer D35

45 Bracket

46 Retainer

47 Cover

48 Housing Support

49 Bolt M6x30

50 Fan

51 Fan Clip

52 Fan Cover

53 Bolt M5x12

54 Nut M5

55 Rear Cover

56 Bolt St4.8x16

57 Delivery Pipe

58 Nut M8

59 Release Pipe

60 Bolt M8x25

61 One-way Valve

62 Axle

63 Wheel

64 Plug

65 Nut M10

66 Flat Gasket

67 Drain Plug

68 Bolt M8x25

69 Foot

70 Nut M8

71 Locking Nut

72 Pressure Regulator

73 Safe Valve

74 Quick Couple

75 Pressure Gauge

76 Pressure Switch

77 Plug And Lead

78 Rubber Hand Handle

79 Tank

80 Motor Lead

81 Handle

82 Bolt M8x8

83 Wheel Set

17

DECLARATION OF CONFORMITY

18

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

DECLARATION OF CONFORMITY

19

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]