Clarke PC108, PC109, PC216, PCSF109, PKP411 Operating/safety Instructions Manual

OPERATING & SAFETY

INSTRUCTIONS

GC04/14

HEATING TORCH SETS

Models; PC108, PC109, PCSF109, PC216, PKP411,

PS555, PS560 & PLK1074

Part Nos: 3404115, 3404100, 3404105, 3404110, 3404125, 3404000,

3404005 & 3404135

2

Parts & Service: 020 8988 7400/E-mail:[e-mail] or [e-mail]

INTRODUCTION

Thank you for purchasing this CLARKE Heating Torch Set, designed for trade
use. They are all to be used only with propane gas and are supplied with a
standard 3/8”BSP (LH) hose.

Before attempting to use the product, it is essential that you read this manual
thoroughly and carefully follow all instructions given. In doing so you will
ensure the safety of yourself and that of others around you, and you can also
look forward to the product giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of
12 months from the date of purchase. Please keep your receipt as proof of
purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for its intended purpose.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

SAFETY PRECAUTIONS

1. ALWAYS follow all precautions regarding the use of Propane gas cylinders.
(see manufacturers/suppliers instructions)

2. Ensure the gas hose is in perfect condition before use. If in doubt, have it
replaced.

3. Ensure all connections are fully secure before use.

4. Never transport the gas bottle by holding the regulator or gas hose.

5. NEVER point the torch at any person or animal.

6. Take great care when placing the torch down. Do not allow it to come
into contact with flammable surfaces, or any surface which could be
damaged by heat. Use the stand supplied with the PLK1074 to support the
nozzles clear of any supporting surface.

7. Never use the torch in an explosive atmosphere, or where there is danger
of fire.

8. IMPORTANT! If used indoors, ensure there is adequate ventilation.

Please keep these instructions in a safe place for future reference.

3

Parts & Service: 020 8988 7400/E-mail:[e-mail] or [e-mail]

ASSEMBLY

NOTE: A bottle of propane gas is required for use with this equipment, capable of
delivering a pressure of 4 bar. (A regulator is provided)

1. Turn the knob on the regulator fully clockwise, then attach the
regulator to the gas bottle, ensuring it is tight.

2. Attach the hose supplied, to the regulator at one end, and the torch at
the other, noting that the hose connections have LEFT HAND THREADS, i.e.
turn them anticlockwise.

3. Attach the appropriate nozzle/burner to the torch where necessary.

If a nozzle/burner is already attached, remove it carefully, complete with
adapter (see illustration below). Unscrew the nozzle from the adapter and
replace with that of the desired type or size. Screw the adapter with nozzle
back on to the torch.

Note:

1. Model PKP411 requires the torch extension to be attached to the torch.

OPERATION

With the hose and regulator attached, and ensuring the gas tap on the torch
is closed, i.e. turned fully clockwise, open the gas regulator valve.

Gas will now be available at the torch, the volume of which will depend
upon the regulator valve opening.

Very gently, open the gas valve on the torch, ensuring the nozzle/burner is
pointing well away from people or property, and apply a flame to the end of
the burner. Model PKP411 is equipped with a piezo electric starter on the
torch extension. Press the button until ignition occurs. Adjust the gas valve
until the desired flame is achieved.

Some models have a control lever attached to the torch. This is used to
further regulate the gas flow and hence the intensity of the flame. When the
lever is released the flame will reduce to a pilot light.

4

Parts & Service: 020 8988 7400/E-mail:[e-mail] or [e-mail]

In the case of the PC109 kit, the flame can also be adjusted by positioning
the clip-on sleeve provided, over the air holes in the circumferance of the
17mm screw-tipped nozzle.

Models PC216,
PKP411 and
PLK1074 have
a support arm
which can be
clamped to
the nozzle
extension to
steady the unit
at rest. This
should be
fitted to ensure the flame points upwards, away from any supporting surface.

MAINTENANCE

The torches are maintenance free, except for visual checks before use to
ensure all connections are secure, and the gas hose is in perfect condition. If
the nozzle becomes sooted, clean with a soft wire brush. DO NOT poke wire
etc, through the holes in the nozzle.

To remove the filter from the nozzle for cleaning, grasp the nozzle with a pair
of mole grips or very carefully secure in a vice, then unscrew the filter.

The parts on the following pages are all available from your CLARKE dealer.

COMPONENT PARTS

PLK 1074

5

Parts & Service: 020 8988 7400/E-mail:[e-mail] or [e-mail]

PC 108

PC 109

PCSF 109

PC 216

Sleeve may be used to
adjust air mix by covering
holes as necessary to
produce desired flame.

6

Parts & Service: 020 8988 7400/E-mail:[e-mail] or [e-mail]

PKP 411

PS 555

PS 560

7

Parts & Service: 020 8988 7400/E-mail:[e-mail] or [e-mail]

SPARE PARTS LIST

feR noitpircseD oNtraP feR noitpircseD oNtraP

1

ylbmessAeldnaH10901CFDI12renruBepiP12901FSCFDI

2yssAreggirT/eldnaH20114KFDI22renruBtalF22901FSCFDI

3yssAbo

nKlortnoC30901CFDI32

rotpadAnorIgniredloS

32101KFDI

4mm08noisnetxE40901CFDI42norIgniredloS42101KFDI

5mm011noisnet

xE50801CFDI52ntxehtiwrenruBepiP52555SFDI

6mm053noisnetxE60612CFDI62ntxehtiwmm41elzzoN62555SFDI

7)tik(mm01noisnetx

E70065SFDI72ntxehtiwmm22elzzoN72555SFDI

8)tik(mm062noisnetxE80065SFDI82

wen(rotalugeRsaG

)*elyts

*82555SFDI

9)P(mm

006noisnetxE90114PKFDI92pmalC92114PKFDI

01mm0051esoH01901CFDI03

)elbaccni(retingIozeiP

03114PKFDI

11mm0002esoH1155

5SFDI13

revoCnoisnetxE

13114PKFDI

21mm000,01esoH21612CFDI23

dnatStroppuS

23114KFDI

31mm9elzzoN31901CFDI33hcnerWnepO3

3114KFDI

41mm21elzzoN41901CFDI4371tifoteveelslateM

elzzonpit-wercsmm

53meti

43901CFDI

51mm51elzzoN51901CFDI53elzzo

NpiTwercSmm7153901CFDI

61mm52elzzoN61801CFDI63mm0005esoH634701KLPFDI

71mm43elzzoN71801CFDI73renruBmm06niwT734701KL

PFDI

81mm84elzzoN81801CFDI83mm005noisnetxE834701KLPFDI

91mm85elzzoN91612CFDI93noitceSkroF934701KLPFDI

02mm06obruTel

zzoN02114PKFDI

ENVIRONMENTAL PROTECTION

Do not dispose of this product or its packaging with general
household waste. All tools, accessories and packaging contain
valuable raw materials and should be sorted, taken to a recycling
centre and disposed of appropriately.