Clarke S2426, L2426 User Manual

Page 1
ENCORE
IVIE Enterprises
S2426 and L2426
Section II

Parts and Service Manual

(70200A)
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -27-
Page 2

HOW TO CORRECT PROBLEMS IN THE MACHINE

PROBLEM CAUSE ACTION
There is no solution flow.
The solution flow does not stop.
The machine does not remove all the water from the floor.
The solution tank is empty.
The solution valve is closed.
There is an obstruction in the solution hose or filter.
The solution valve or electric wiring is damaged.
The solution module is defective.
The solution valve is open.
The solution valve or wiring is damaged.
The solution valve is dirty
There is a damaged seat and washer in the solution valve.
The solution module is defective.
The squeegee is up.
The squeegee tilt is not correct.
The recovery tank is full.
The screen filter is dirty.
Fill the solution tank.
Open the solution valve.
Remove the obstruction from the hose or filter.
Repair or replace the valve or the electric wiring.
Replace solution module
Close or Clean the solution valve.
Repair or replace the valve and the wiring.
Clean the solution valve.
Replace the seat and washer.
Replace solution module.
Lower the squeegee.
To adjust See Figure 11, page 23.
Drain the recovery tank.
Clean the screen filter.
The batteries do not give the normal running time.
There is an obstruction or damage in the squeegee, squeegee hose or standpipe.
The vacuum motor is not running.
The squeegee hose is disconnected, or damaged
The squeegee blade is damaged, worn, or incorrectly installed.
The gaskets on the cover of the recovery tank are damaged.
The battery terminals are dirty or damaged.
The electrolyte level is too low.
The batteries are not fully charged.
The charger is damaged.
The battery is defective.
The batteries are disconnected.
Remove the obstruction or repair the damage.
Check for tripped breaker. Have an authorized service person make repairs.
Check and connect hose.
Turn or replace the squeegee blade. Correctly install the squeegee blade.
Replace the gaskets.
Clean the terminals and connectors. Replace the damaged cables. Charge the batteries.
Add distilled water to each cell and charge the batteries.
Charge the batteries for a full 16 hour charge.
Have an authorized service person repair the charger.
Check voltage of each cell while discharging.
Connect the batteries.
Brush is in heavy scrub setting.
Page -28- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Adjust Pressure.
Page 3
PROBLEM CAUSE ACTION
IVIE Enterprises
The cleaning is not even. The scrub brush or pad is worn.
There is damage to the brush assembly, caster or the solution valve.
The brush motor is not running
The solution level is low.
The machine does not run. The machine loses power.
Key or switch is off.
Batteries are unplugged. Battery terminals are dirty.
Batteries are discharged
Replace the scrub brush or pad.
Have an authorized service person make the needed repairs.
Check for tripped breaker. Reset. Check for loose connections.
Fill the solution tank.
NOTE: If the problem continues consult an authorized service person.
Reset the circuit breaker.
Turn key or switch on.
Check the battery connections.
Check battery gauge and recharge NOTE: If the problem continues consult an authorized service person.
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -29-
Page 4
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/ L2426
Final Assembly Drawing 11/23/00
23
22
24
25
27
28
26
31
29
27
32
30
1
2
7
9
8
11
10
8
4
3
5
6
4
15
21
16
17
18
20
19
9
8
10
8
13
14
8
10
11
11
12
Page -30- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 5
CLARKE TECHNOLOGY
Encore S2426/L2426
Final Assembly Parts List 11/23/00
Qty Qty
Ref. # Part No. Description “L” “S”
1 10062A Assembly, Recovery Tank 1 1 2 10065A Assembly, Control Panel “L” 1-
10066A Assembly, Control Panel “S” -1
3 30064A Rear Cover 1 1 4 80108A Screw, 10-24 x ½ SS 4 4 5 70080A Plate, Warning 1 1 6 83010A Rivet, Pop 1/8 22 7 10064A Assembly, Rear Panel “L” 1-
10067A Assembly, Rear Panel “S” -1
8 980651 Washer, 5/16 Flat 11 11
9 920110 Nut, 5/16 -18 ESNA 4 4 10 980652 Washer, 5/16 Lock 7 7 11 85811A Screw, 5/16 -18 x ¾ 7 7 12 10129A Assembly, Squeegee 32” 1 1 13 10075A Assembly, Squeegee Lift 1 1 14 10069A Assembly, Traverse System “L” 1-
10070A Assembly, Non-Traverse System “S” -1
15 980982 Washer #10 2 2 16 10071A Assembly, Brush Head “L” 1-
10061A Assembly, Brush Head “S” -1
17 81105A Nut, 3/8-16 ESNA 4 4 18 87031A Washer, 3/8 Flat SS 4 4 19 50965A Hinge 1 1 20 85395A Screw, ¼-20 x 1/2 SS 6 6 21 30059A Front Cover 1 1 22 50966A Latch, Front Cover Ref Ref 23 930090 Rivet, 5/32 x 9/16 22 24 10063A Assembly, Solution Tank 1 1 25* Page 12 Battery
871334 Battery 12V, 195 AH (wet - UT Post) - 2 871335 Battery 12V, 195 AH (dry - UT Post) - 2 40136A Battery 6V, 250 AH (wet - Stud Post) 4 4 40137A Battery 6V, 250 AH (dry - Stud Post) 4 4 891384 Battery, 6V 330 AH (wet - UT Post) 4 4 891385 Battery, 6V 330 AH (dry - UT Post) 4 4
26 41206A Series Battery Cable (Taper Style) 3 3
41217A Series Battery Cable (Ring Style) 3 3 27 980205 Washer, 5/16 Fender 4 4 28 85734A Screw, 5/16-18 x 2 2 2 29 85739A Screw, 5/16-18 x 3 Hex 2 2 30 87026A Washer, ¼ flat SS 5 5 31 41211A Battery, Cable (Taper Style) 1 1
40174A Battery, Cable (Ring Style) 1 1 32 85518A Screw, ¼-20 x 3/4 55 NI 10132A Lit Kit 1 1 NI 17531A Pad Driver Assembly 1 -
10140A Pad Driver Assembly - 1 NI 40512A Battery charger 1 1 NI 77092A Label, Gases 1 1 NI 77093A Label, Falling 1 1 NI 70226A Label, Battery 1 1 NI 30070A Accessory Bag 1 1 NI 10072A Parking Brake Assembly "L" 1 ­NI 10073A Parking Brake Assembly "S" - 1 * See page 12 for installation.
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -31-
Page 6
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Recovery Tank Assembly Drawing 8/00
Drawing #10062A
1
2
43
34
35
36
20
37
38
39
3
43
40
19
7
17
18
16
4
5
42
6
8A
8B
7
9
8
12
41
10
26
18
30
33
25
32
24
23
29
Page -32- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
22
27
28
16
31
21
14
15
13
#40 Recommended Torque 175 + or - 5 inch pounds
11
Page 7
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Recovery Tank Assembly Parts List 8/00
Ref. # Part No. Description Qty
1 962798 Screw, 10-24 x .5 1 2 30057A Lid 1 3 81110A Nut, 10-24 SS 1 4 30065A Gasket, Lid 1 5 58069A Strainer 1 6 39338A Stand Tube 1 7 837304 O-Ring 2 8 10660A Switch Kit, (Includes 8A, 8B, 9) 1 8A 40002A Switch (included in Item 8) 1 8B 56459A Relief, Strain (included in Item 8A) 1
9 59877A Seal, Washer 1 10 30061A Tank, Recovery 1 11 60373A Latch, Recovery Tank 1 12 87622A Washer, Nylon 5/16 x 5/8 x 1/32 1 13 80043A Screw, .25 x 20 x .25, Shoulder 1 14 60336A Strap, Hose Retainer 1 15 85100A Screw, 10-32 x ½ SS Xylan Coating 2 16 30068A Hinge, Pin (included w/ item 10) 2 17 43402A Housing, Connector(included in 8A) 2 18 41809A Contact (included in 8A) 4 19 82100A Nut, Strain Relief Lock 1 20 872010 Clamp, Hose 1 21 35165A Hose, Drain 1 22 832002 Clamp, Hose 1 23 839401 Valve, Drain 1 24 962943 Screw, 8-18 x ½ PN 1 25 52206A Chain 1 26 962987 Screw, 10-24 x 3/8 Pan 1 27 833901 Drain, Valve Handle 1 28 833407 Gasket, Drain Valve 1 29 51060A Hose, Squeegee 1 30 830208 Squeegee Stand Tube 1 31 80110A Hose Clamp 1 32 752020 Hose Clamp 1 33 43401A Housing, Vac Motor Connector 2 34 674110 Hose 1 35 85728A Screw, ¼-20 x 4 Hex 3 36 87026A Washer, ¼ Flat 3 37 51049A Motor, Vacuum (3-Stage) 1
51050A Motor, Vacuum, (2-Stage Option) 1 38 643418 Gasket 1 39 58533A Spacer 3 40 920797 Nut 1 41 962666 Screw, 10-24 x ¾ 1 42 920296 Nut, 10-24 Elastic 1 43 38020A Strap 1 NI 839410 Valve Asm. (includes 23, 24, 25, 26, 27, 28) 1 NI 70226A Label, Battery Installation 1
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -33-
Page 8
CLARKE TECHNOLOGY Encore S2426/L2426
IVIE Enterprises
Solution Tank Assembly Drawing 5/01
Drawing #10063A
20
19
21
25
17
16
18
23
2
1
24
3
22
5
14
12
9
4
5
10
11
5
8
5
5
8
5
5
7
13
6
Page -34- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 9
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Solution Tank Assembly Parts List 5/01
Ref. # Part No. Description Qty
1 872010 Clamp, Hose 1 2 50964A Hose, Drain 1 3 30060A Tank, Solution 1 4 59614A Valve, Battery Drain 1 5 722030 Clamp, Hose 6 6 30453A Hose, Clear Vinyl 1 7 820207 Adapter, Hose 3/8 MPT x ½ Hosebarb 1 8 30412A Hose, Stretch 2
9 51205A Adapter, Female 1 10 838517 Filter, Screen 1 11 830214 Adapter, Male, ¾ Barb x GHT Male Thread 1 12 51204A Valve, Solution 1 13 59789A Valve, Solution 1 14 38014A Splitter 1 15 81109A Nut, 8-32 ESNA SS 2 16 50966A Latch 1 17 80105A Screw, 8-32 x 1¼ SS 2 18 50963A Screen, Fill (with hose retention) 1
51308A Strainer (without hose retention) 1 19 69879A Bracket, Latch 1 20 170892 Washer, Lock ¼ 2 21 170915 Screw, ¼-20 x ¾ SS Hex 2 22 51059A Valve Assembly, Solution Shut-Off (incl. #9,12) 1 23 60480A Bracket, Hose 1 24 51346A Spring, Hose 1 25 80108A Screw, 10-24 x ½ 2 NI 30162A Funnel (included w/Kit 10177A) 1 NI 10177A Kit, Solution Fill 1
(includes #18-51308A)(includes NI - 30162A)
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -35-
Page 10
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Rear Panel Assembly Drawing 8/00
Drawing #10064A (L)
Drawing #10067A (S)
32
35
2
1
36
3
34
34
33
9
10 31
9
10
1
2
5
4
6
7
8
9
10
26
23
37
25
6
29
28
3
11
27
22
2
24
30
3
18
20
21
19
10
11
16
13
15
17
16
15
14
12
Page -36- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 11
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Rear Panel Assembly Parts List 5/01
Ref. # Part No. Description Qty Qty
LS
1 920224 Nut, 10-32 2 ­2 980603 Washer, Starlock 4 2 3 920056 Nut, 6-32 5 4 4 46106A Rectifier 1 ­5 40133A Harness, Power “L” 1 -
40134A Harness, Power “S” - 1 6 962212 Screw, 6-32 x 7/8 3 2 7 85383A Screw, 10-32 x ¾ 1 ­8 41810A Solenoid, Brush 1 1 9 85395A Screw, ¼-20 x ½ 6 6
10 980614 Washer, Starlock, ¼ 10 10 11 85391A Screw, ¼-20 x 5/8 4 4 12 60261A Panel, Rear Metal 1 1 13 60257A Cable, Squeegee Lift 1 1 14 920346 Nut, Pal 1 1 15 80028A Bolt, Shoulder, 5/16 x 1.0 1 1 16 980692 Washer, Flat 5/16 SS 2 2 17 438360 Spring 1 1 18 64901A Lever, Squeegee Lift 1 1 19 64490A Handle, Squeegee 1 1 20 980666 Washer, 3/8 Starlock 1 1 21 85389A Screw, 3/8-16 x 5/8 1 1 22 68643A Plate, Vacuum Wear 1 1 23 962968 Screw, 10-24 x ½ 2 2 24 61260A Plate, Squeegee Lift 1 1 25 47374A Switch, Vacuum Lever 1 1 26 85601A Screw, 6-32 x 1¼ PN 2 2 27 81217A Nut, ¼-20 x .218H Nylock 1 1 28 60264A Bracket, Power Connector 1 1 29 41146A Cable, Assembly Console 1 1 30 193951 Grommet, slotted, 8” Ref Ref 31 41811A Solenoid, Main 1 -
41810A Solenoid, Main - 1
32 40157A Harness, Traverse 1 ­33 40169A Solenoid, Vacuum 1 1 34 962798 Screw, 10-24 x ½ 4 2 35 40132A Control, Traverse 1 ­36 14097A Low voltage Shutoff - 1 37 30097A Insulator, Mylar 1 1 NI 77093A Label, Falling Parts 1 1 NI 77092A Label, Gases 1 1 NI 47809A 3/8 Ring Terminal, 14-16 - 1 NI 911933 #10 Ring Terminal, 14-16 - 1 NI 40519A Ring Terminal, 5/16 - 1
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -37-
Page 12
27
IVIE Enterprises
28
40
29
34
CLARKE TECHNOLOGY Encore S2426/L2426
Control Panel Assembly Drawing 8/00
Drawing #10065A "L" and 10066A "S"
1
2
4
7
3
37
56
35
36
7
30
33
32
36
31
27
38
12
11
8
10
11
19
14
18
26
25
15
16
15
16
30
16
39
16
15
2
5
5
23
24
22
15
21
20
9
3
17
Page -38- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 13
CLARKE TECHNOLOGY Encore S2426/L2426
IVIE Enterprises
Control Panel Assembly Parts List 8/00
Qty Qty
Ref. # Part No. Description “L” “S”
1 55413A Key (included w/Item 3) Ref Ref 2 84237A Screw, 10-32 x ½ 2 2 3 47380A Switch, Key 1 1 4 60334A Panel, Key Switch 1 1 5 80108A Screw, 10-24 x ½ SS Black Xylan 8 8 6 87052A Washer, Switch 1 1 7 962262 Screw, Set 8-32 x ½ (included in item 29) 4 2 8 50962A Traverse, Control Knob 1 -
9 85703A Screw, 10-00 x ½ PN 1 1 10 962957 Screw, 10-16 2 ­11 40135A Harness, Potentiometer Assembly. 1 ­12 60259A Bracket, Traverse Switch 1 ­13 980666 Washer, 3/8 Starlock 1 ­14 40158A Switch, Reverse 1 ­15 980603 Washer 4 2 16 920224 Nut, 10-32 Hex 4 2 17 30062A Control Handle 1 -
30072A Control Handle - 1 18 85391A Screw, ¼-20 x 1/2 SS Ref Ref 19 87026A Washer, ¼ SS Ref Ref 20 44308B Control, Solution 1 1 21 41422A Breaker, Circuit 25 Amp Traverse 1 ­22 41433A Breaker, Circuit 40 Amp Brush 2 2 23 41448A Breaker, Circuit 30 Amp Vac 1 1 24 41423A Breaker, Circuit 5 Amp Actuator 1 1 25 70186A Label, Control “L” 1 -
70187A Label, control “S” - 1 26 60258A Panel, Control, Metal 1 1 27 40217B Meter, Battery 1 1 28 40168A Switch, Brush Adjustment 1 1 29 55502A Knob 1 1 30 51057A Meter, Brush 1 1 31 962330 Screw, 6-32 x 3/8 44 32 980608 Washer 4 4 33 30056A Housing, Switch & Lever 2 2 34 30055A Lever, Switch 2 2 35 50961A Spring, Switch 4 4 36 40126A Switch, Forward/Reverse 2 2 37 80104A Screw, 10-32 x ½ SS Black Xylan 4 4 38 70219A Label, Key Switch 1 1 39 34264A Gasket, Panel 1 1 40 30096A Gasket, Switch 1 1 NI 47708A ¼ F.I.M.Q.D. 4 2 NI 47712A ¼ F.I.F.Q.D. 1 0 NI 912226 Meter, Hour (Optional)
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -39-
Page 14
CLARKE TECHNOLOGY Encore S2426/L2426
IVIE Enterprises
Squeegee Lift Assembly Drawing 6/00
Drawing # 10075A
20
12
22
19
17
21
15
6
1
2
3
4
5
6
14
13
18
15
11
16
15
10
8
8
9
7
Page -40- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 15
CLARKE TECHNOLOGY Encore S2426/L2426
IVIE Enterprises
Squeegee Lift Assembly Parts List 6/00
Ref. # Part No. Description Qty
1 61263A Bracket Tube 1 2 85730A Screw, 3/8-16 x 1¼, Hex SS 1 3 980638 Lockwasher, 3/8 LT Spring Type 1 4 69860B Bracket, Pin 1 5 87026A Washer, ¼ SS 2 6 170915 Screw, ¼-20 x ¾ 4 7 962481 Screw, ¼-20 x 1¼ Hex 2 8 87031A Washer, 3/8 Flat 3
9 920208 Nut, ¼-20 2 10 81111A Nut, 3/8-16 ESNA 1 11 80101A Screw, ¼-20 x 3¼ SS 1 12 85811A Screw, 5/16-18 x ¾ 1 13 67867A Nut, spacer 1 14 60256A Squeegee, Pivot Arm 1 15 81104A Nut, ¼ Nylock 5 16 60255A Bracket, Squeegee 1 17 60328A Mount, Squeegee 1 18 81112A Nut, 5/16-18 Thin ESNA SS 1 19 Page 37 Cable, Squeegee Lift Ref 20 Page 37 Lift Handle Assembly Ref 21 920346 Palnut Ref 22 980651 Washer 1
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -41-
Page 16
CLARKE TECHNOLOGY Encore S2426/L2426
Squeegee Assembly Drawing 10/00
Drawing # 10068A and 10129A
6
1
2
18
17
19
3
4
20
7
8
4
5
16
15
13
14
9
10
11
12
Page -42- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 17
CLARKE TECHNOLOGY Encore S2426/L2426
IVIE Enterprises
Squeegee Assembly Parts List 10/00
10068A
39" 32"
Ref. # Part No. Description Qty Qty
1 962720 Screw, ¼-20 x ½ Hex SS 4 4 2 980657 Washer, ¼ Lock 4 4 3 60243A Bracket, Squeegee Wheel 2 2 4 30049B Wheel, Squeegee 4 4 5 81104A Nut, ¼-20 2 2 6 60254A Bolt, Shoulder
5
/16x 2¼ 2 2 7 50958A Ring, 3/8 ID Snap 2 2 8 30048A Wheel, Guide, 4 Inch Diameter 2 2 9 60272A Channel, Squeegee Weldment 39” 1 -
60234A Channel, Squeegee Weldment 32” - 1 10 50835A Latch, Squeegee Clamp 1 1 11 930086 Rivet, 3/16 x .450 Aluminum 2 2 12 60252A Strap, Clamp, Squeegee Retainer 39” 1 -
60232A Strap, Clamp, Squeegee Retainer 32 - 1 13 30069A Blade, Rear, Gum Rubber, 39” 1 -
30067A Blade, Rear, Gum Rubber, 32” - 1 14 30058A Spacer, Squeegee 39” 1 -
30047A Spacer, Squeegee 32 - 1 15 30091A Blade, Front Ribbed 39” 1 -
30066A Blade, Front Ribbed 32” - 1 16 80011A Screw, 3/8-16 x 3 2 2 17 81301A Nut, 3/8-16 Jam SS 2 2 18 34260B Gasket 1 1 19 25201A Knob 2 2 20 60358A Shim, Squeegee Wheel 2 2
10129A
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -43-
Page 18
CLARKE TECHNOLOGY Encore S2426/L2426
IVIE Enterprises
Frame Axle Assembly Drawing 11/23/00
Drawing #10069A and 10070A
20
22
Page -44- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 19
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Frame Axle Assembly Parts List 11/23/00
Traverse
Ref. # Part No. Description Qty Qty
1 85700A Screw, ¼-20 x 1 1 ­2 85811A Screw, 5/16-18 x ¾ 6 6 3 980652 Washer, 5/16 Lock 6 8 4 980651 Washer, flat 5/16 66 5 60328A Squeegee Mount Ref Ref 6 60260B Frame Assembly 1 1 7 50968A Caster, Assembly 1 1 8 30071A Wheel Assembly 2 -
69205A Wheel, Non Traverse - 2
9 50967A Transaxle w/mounting hubs 1 -
60266A Non-Traverse Axle Assembly - 1 10 60289A Mount, Transaxle 2 ­11 87031A Washer, flat 3/8 SS 4 4 12 170883 Washer, 3/8 Lock 4 4 13 80103A Screw, 3/8-24 x 1 Hex SS 4 4 14 57423A Ring, Snap Retainer - 2 15 87616A Washer, Nylon - 2 16 980205 Washer, 5/16 Fender 2 2 17 962620 Screw, 5/16-24 x ¾ - 2 18 87026A Washer, Flat, ¼ SS 8 ­19 81217A Nut, ¼-20 SS Thin 9 ­20 34711B Wheel Cover 2 2 21 85395A Screw, ¼-20 x ½ SS 2 2 22 980614 Washer, ¼ Starlock 5 2 23 59789A Valve Solution Ref Ref 24 81105A Nut, 3/8-16 ESNA Ref Ref 25 87031A Washer, Flat 3/8 SS Ref Ref 26 Ref Solution Tank Ref Ref 27 980205 Washer, 5/16 Ref Ref 28 85734A Screw, 3/8-16 x 2 Ref Ref 29 69639A Strap, Static 1 ­30 10135A Hub, Transaxle (includes #9) 31 77267A Label, Tie Down 4 4 32 81108A Nut, 3/8-24 ESNA 4 4
Non-Traverse
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -45-
Page 20
70
IVIE Enterprises
72
67
69
71
CLARKE TECHNOLOGY
Encore S2426/L2426
Brush Head Assembly Drawing 8/00
Drawing #10071A and 10061A
1
2
1
3
4
5
77
68
21
59
60
58
74
75
76
64
63
62
25
61
6
7
8
9
10
6
65
73
7
66
14
11
12
13
15
16
17
15
31
51
50
44
40
49
46
45
41
39
53
52
48
55
54
52
25
47
40
43
42
57
56
41
37
38
38
37
31
32
20
30
36
19
33
11
28
29
18
21
27
34
22
26
23
24
25
Page -46- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
35
Page 21
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Brush Head Assembly Parts List 8/00
Drawing #10071A and #10061A
Ref. # Part No. Description L S
1 38708A Washer, Spacer Nylon 2 2 2 50950A Actuator 1 1 3 60265A Plate, Nut 2 2 4 47374A Switch, Lever 1 1 5 47422B Switch, Whisker 1 1 6 980608 Washer, #6 4 4 7 962980 Screw, 6-32 x 1 4 4 8 60251A Mount, Switch 1 1 9 82501A Pin 1 1 10 60236A Bracket, Brush Head 1 1 11 766780 Pin, Hair 5 5 12 85838A Screw, ½ x 20 x 1½ 4 4 13 980673 Washer 4* 4* 14 63058A Bar, Linkage 4 4 15 67705B Bearing, Sleeve 8 8 16 920278 Nut, ½-20 SS 8 8 17 980626 Washer, ½ Lock 4 4 18 80100A Screw, ½-20 x 1 Hex Head 4 4 19 80091A Pin, Brush Lift 1 1 20 60239A Mount, Brush Head 1 1 21 81217A Nut, ¼-20 ESNA .218 Height 3 3 22 60335A Bracket, Brush Housing 1 1 23 170915 Screw, ¼-20 x ¾ SS 2 2 24 782002 Clamp, Hose 2 2 25 81104A Nut, ¼-20 ESNA 7 7 26 34705A Hose, Solution 2 2 27 722030 Clamp, Hose 2 2 28 962989 Screw, ¼-20 x 1½ 2 2 29 38014A Solution Splitter Ref Ref 30 60235A Plate, Brush Head 1 1 31 962992 Screw, 8-32 x 5/8 SS 4 4 32 55721A Latch, Brush Housing 1 1 33 30053A Housing, Left Brush 1 1 34 30051A Skirt, Left 1 1 35 85616A Screw, 10-32 x 5/8 SS 12 12 36 82004A Nut, “T” 10-32 12 12 37 81109A Nut, 8-32 SS ESNA 4 4 38 60337A Plate, Latch Brush 2 2 39 Page 24 Brush/Pad Assemblies
* Used only as required to square up linkage bar #14 to the frame.
Qty Qty
Qty Qty
Ref.# Part No. Description L S
40 962714 Screw, 5/16-18 x ¾ Soc. 2 -
85811A Screw, 5/16-18 x ¾ Hex - 2
41 34400B Gimbal Male 2 -
20308A Motor, Adapter - 2 42 61658A Gimbal, Collar 2 ­43 59856A Washer, Rubber 2 ­44 980652 Washer, 5/16 Lock - 2 45 980210 Washer, Impeller - 2 46 980679 Washer, Spacer - 2 47 962244 Screw, 3/8-16 x ¾ 8 8 48 980638 Washer, Lock 3/8 8 8 49 30052A Skirt, Right 1 1 50 30054A Housing, Right Brush 1 1 51 55451A Keeper 1 1 52 87039A Washer, ¼ 2 2 53 30048A Wheel, Guide 1 1 54 60248A Sleeve Guide Wheel 1 1 55 85301A Screw, ¼-20 x 1¼ 1 1 56 20014A Spacer, Brush Tilt - 2 57 915102 Key (included w/Item 58) 2 2 58 44809B Motor, Brush 2 2 59 41602A Housing 4 4 60 41601A Connector 4 4 61 60240A Bushing, Swivel Adj., ¼ 4 4 62 50839A Pin, Plunger 1 1 63 50956A Spring, Plunger 1 1 64 50957A Knob 1 1 65 60241A Bushing, Swivel, 3/8 1 1 66 81105A Nut, 3/8-16 SS ESNA 1 1 67 53422A Spring, Head Pressure 1 1 68 87007A Washer, Flat, ¼” 1 1 69 60238A Tube, Head Pressure 1 1 70 60249A Switch, Actuator 1 1 71 80102A Washer, ¼ 1 1 72 85702A Screw, ¼-20 x 1¾ 1 1 73 87031A Washer, 3/8 Flat Ref Ref 74 80109A Nut, ½-20 Jam S.S. 4 4 75 980603 Washer, #10 2 2 76 80108A Screw, 10-24 x ½ 2 2 77 30092A Insulator, Mylar 1 1 NI 77091A Label, Moving Parts 2 2
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -47-
Page 22
16
CLARKE TECHNOLOGY
Encore S2426/L2426
Optional Brake Drawing and Parts List 11/23/00
10073A - "S" Model
1
7
11
14
4
5
5
2
3
1
15
2
4
7
5
11
12
11
15
13
6
9
15
6
14
10
4
4
6
8
5
7
5
5 4
5
4
Ref. # Part No. Description Qty
1 85811A Screw, 5/16-18 x ¾ 2 2 60359A Pad, Brake 2 3 60271A Brake, Bar L.H. 1 4 920110 Nut, 5/16-18 ESNA 6 5 980651 Washer, Flat, 5/16 10 6 67877A Spacer 3 7 85814A Screw, 5/16-18 x 1¼ 3 8 60268A Lever, Brake Pedal 1 9 60361A Cam, Brake 1 10 60267A Rod, Brake 1 11 81104A Nut, ¼-20 ESNA 4 12 848508 Swivel, Rod, Brake 2 13 87026A Washer, Flat, ¼ 1 14 50969A Spring, Brake Asm. 2 15 87607A Washer, Flat Nylon 4 16 60362A Brake, Bar R.H. 1 NI 77266B Label, Parking Brake 1
12
5
11
4
Page -48- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 23
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Optional Brake Drawing and Parts List 5/01
10072A - "L" Model
3
4
5
2
6
1
Ref # Part No. Description Qty
1 50981A 2 60388A Spacer 1 3 30095A Tie, Cover Retainer 1 4 80123A Nut, Brake Drive 1 5 80125A Key, 3/32 Sq. x 1/4 Lg. 1 6 30094A Cover, Vinyl 1 7 80124A Screw Set (Brake Nut 2
to Motor Shaft)
8 10160A Brake, Asm. 24V 1
7
8
NOTE: Only use spacer (ref. #2) on transaxles that have a circular step and mounting nuts protruding from end of motor. The motor that uses the spacer can be identified by the motor brush caps protruding past the outside diameter of the motor.
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -49-
Page 24
CLARKE TECHNOLOGY
Encore S2426/L2426

Vacuum Motor Drawing and Parts List

Drawing 5/00
TO
Page -50- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 25
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Gearbox Assembly Drawing and Parts List 5/00
Form #54238A
9
8
7
6
5
4
3
2
1
Ref # Part No. Description Qty
1 57846A Ring, Snap 1 2 507641 Seal, Oil, Small 1 3 52050A Cap End 1 4 56668A O-Ring 1 5 51176a Bearing, Large 1 6 58316A Shaft & Gear 1 7 902605 Bearing, Small 1 8 54883A Housing 1 9 58144A Seal, Oil Large 1 10 NI Darina EP2 Grease 4 oz.
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -51-
Page 26
CLARKE TECHNOLOGY
Encore S2426/L2426
Brush Motor Drawing & Parts List 8/00
Motor Asm. 44809B
Seam Location
13
7
12
1
2
12
13
3
14
16
4
5
15
6
17
8
9
10
11
Item Part No. Description Qty
1 56478A Stator Frame Assembly (w/Magnets & Clips) 1 2 50142A Armature Assembly (w. B.E. & F.E. Bearings) 1 3 902654 Bearings B.E. 1 4 902550 Bearing F.E. 1 5 Commutator Bracket Assembly 1
*
6 50520A Commutator Bracket 1 7 56480A Strain Relief 2 8 962546 Brush Board Screw 2 9 50517A Brush Board Assembly (w/ Springs & Brushes) 1 10 448396 Brush Spring 4 11 40826A Brush Assembly 4 12 55657A Lead Assembly 1 13 55656A Lead Assembly 1 14 Helical Washer 1
*
15 50515A Thru Bolt 2 16 80501A Shaft Key 1 17 54238A B.E. Bracket Assembly (Gear Box) 1
(w/Brush BRD Assembly Leads)
* NOTE: Parts not available at this time.
Page -52- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 27
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426/L2426
Transaxle Drawing 5/00
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -53-
Page 28
CLARKE TECHNOLOGY
Encore S2426/L2426
Battery Charger Drawing and Parts List 5/00
WARNING: All electrical repairs must be performed by qualified personnel only.
Charger #40512A: 24 volt, 25 amp D.C., 115 volt, A.C., 60 Hz. Charger #40513A: 24 volt, 25 amp D.C., 230 volt, A.C., 50 Hz
Charger Charger
Ref. No. Description 40512A 40513A
1 Charger Case 41129A 41128A 2 Transformer 48413A 48409A 3 Electronic Controller Kit 47500A 48200A 4 Capacitor, 660 V.A.C. 912132 912132 5 Heat Sink Assembly 912212 912212 6 Ammeter 40200A 40200A 7 Fuse Holder 912382 912382 8 Strain Relief, A.C. Cord 837525 837525 9 Strain Relief, D.C. Cord 747553 747553 10 D.C. Cord Assembly 51986A 51986A 11 A.C. Cord Assembly 51974A 908947 12 Housing, Red 911470 911470 13 D.C. Plug Lock Key 795020 795020
* NOTE: Parts not available at this time.
Page -54- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Page 29
CLARKE TECHNOLOGY
IVIE Enterprises
Encore S2426
Connection Diagram (00932A-W) 6/00
CLARKE TECHNOLOGY Operator's Manual - Encore S2426/L2426 Page -55-
Page 30
CLARKE TECHNOLOGY
Encore S2426
Electrical Schematic (00932A-E) 5/00
Page -56- CLARKE TECHNOLOGY Operator's Manual -Encore S2426/L2426
Loading...