Clarke Jumpstart JSM200, 6239000 User guide

POWER PACK & JUMP STARTER

MODEL NO: JSM200

PART NO: 6239000

OPERATION & MAINTENANCE

INSTRUCTIONS

ORIGINAL INSTRUCTIONS

LS1118-ISS 2

INTRODUCTION

Thank you for purchasing this CLARKE product.

Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

ENVIRONMENTAL PROTECTION

Do not dispose of this product with general household waste. All
tools, accessories and packaging should be sorted, taken to a
recycling centre and disposed of according to the laws governing
Waste Electrical and Electronic Equipment.

SPECIFICATIONS

Model Number JSM200

Battery Capacity 7.5Ah

Jumpstart Output Current Starting 200A / Peak 400A

USB Output 5V @ 2.1A

Dimensions (L X W X H) 132 x 75 x 24 mm

Weight 0.56 kg

Engine Capacity UP TO 4L (PETROL ONLY - DO NOT USE ON DIESEL ENGINES)

2

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

GENERAL SAFETY RULES

WARNING: ALL LEAD ACID BATTERIES GENERATE HYDROGEN GAS
DURING NORMAL OPERATION. THIS PROCESS INCREASES DURING A
PERIOD OF RAPID DISCHARGE.

WARNING: HYDROGEN GAS AND BATTERY ACID (SULPHURIC ACID) CAN
BE EXPLOSIVE, CORROSIVE TO SKIN, EYES AND HAIR, DAMAGING TO
CLOTHING AND METALS, FLAMMABLE, POISONOUS TO BREATHE.

1. DO NOT leave it exposed to the elements. Avoid direct sunlight, direct
heat, rain/moisture etc.

2. The device must only be used indoors or completely protected from the
rain. This also applies to any device being powered by the device.

3. Do not operate the device if any of the cables are damaged. Consult
your Clarke dealer for repair or replacement of the parts.

4. Do not operate the device if the case is damaged. Consult your Clarke
dealer or a qualified person for inspection and repair.

5. To prevent the battery from overheating and consequent damage, do
not exceed our recommendations for the duration of jump starting.

6. The unit is NOT designed to be used as a replacement for a vehicle
battery.

7. NEVER allow the battery to become completely discharged.

8. NEVER jump start the engine whilst the unit is being charged.

9. NEVER attempt any repairs yourself. If you have a problem with the unit
contact your local CLARKE dealer.

10. Always keep your body and clothing dry. Never work in a damp area
without adequate insulation against electric shock.

11. Always store the unit out of reach of children.

12. Always wear safety glasses when working with lead acid batteries.

13. If splashed by battery acid, immediately flush the area of the splash with
clean water. If a burning sensation is felt or any blistering occurs, seek
medical help.

14. If battery acid comes into contact with the eyes, flush the eyes with clean
water continuously and seek medical help.

15. Always ensure that there is air circulating around the unit when in use.

16. When not in use, store in a safe dry place.

3

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

17. Never allow the jumpstart leads, to touch each other or to touch the

-

+

same metal object.

18. Ensure the vehicle battery posts and battery clamps are perfectly clean
before use.

19. Connect the red clamp to the unearthed battery terminal first, (this is
usually the positive (+ve) terminal and coloured RED); then connect the
black clamp to the earthed battery terminal, (this is usually the negative (­ve) terminal and coloured BLACK).

20. ALWAYS wear suitable protective clothing and eye protection when
working with lead acid batteries.

21. NEVER allow the cables to become wrapped around the operator or any
other person.

22. Wipe the body of the unit clean using a soft damp cloth, do not use
abrasives to clean this product.

ELECTRICAL CONNECTIONS

This device is supplied with a 13 amp, 230 volt (50Hz), charging adaptor for
connection to a standard, domestic electrical supply.

This appliance is of double insulated design. No earth conductor is provided.

If in any doubt, consult a qualified electrician. DO NOT attempt any electrical
repairs yourself.

SAFETY SYMBOLS

Class II appliance (mains
adaptor only)

Suitable for indoor use
only (refers to mains
adaptor only)

Live centre pin Class III appliance (main

4

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

Always read instructions
before use

Subject to Waste Electrical
& Electronic Equipment
Directive

unit only)

OVERVIEW

NO DESCRIPTION NO DESCRIPTION

1 On/Off Button 4 USB Socket 5V DC

2

Power Indicator Lights

3 Worklight 6 Jumpstart Lead Socket

5 Charger Input Socket

5

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

TO CHARGE THE POWER PACK

You can recharge the power pack
using:

• The mains charger (A) or

• The cigar lighter adapter (B).

1. Switch the power pack off.

2. Plug the mains charger or cigar

lighter adapter into the charger
input socket

3. If you are using the cigar lighter

adapter, start the engine.

4. Connect the other end to either

the mains supply or cigar lighter
socket.

5. When all 4 power indicator lights on the top are lit, disconnect the charger.

TO GET THE MAXIMUM LIFE FROM THE BATTERY

• Charge this device before first use.

• Recharge after every use or a minimum of every 3 months.

• Do not leave the unit in a state of discharge.

6

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

OPERATION

WORK LIGHT

1. Push and hold the ON/OFF button

for 3 seconds to turn the work light
on.

2. Push the ON/OFF button again.

• The work light flashes on and
off.

3. Push the ON/OFF button again.

• The work light flashes with the
morse code SOS pattern.

4. Push the ON/OFF button again to turn the work light off.

USB POWER SUPPLY

• This will supply a maximum of 2.1A at 5V.

1. Put the USB cable into one of the
USB sockets.

2. Connect the other end of the
cable to your device.

• The supplied lead has 4 plugs

on one end which can be used
to charge a variety of devices.

3. Push the ON/OFF button to start
supplying power.

• This supplies a maximum of 2.1A

at 5V.

7

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

JUMP STARTING

WARNING: SOME VEHICLE ELECTRONIC EQUIPMENT MAY BE DAMAGED
BY JUMP STARTING. ALWAYS CHECK WITH THE VEHICLE HANDBOOK

WARNING: DO NOT USE ON DIESEL ENGINES.

NOTE: This device will not jumpstart a vehicle if the battery is very low or

completely flat.

CONNECTING THE SMART CABLE TO THE POWER PACK

1. When jumpstarting, a minimum of
3 of the power indicator lights
located on top of the device must
be lit. Recharge the device if
required.

2. Lift the rubber plug and insert the
EC5 connector of the smart lead
into the power pack.

• The red & green LEDs on the

smart lead flash alternatively.

CONNECT THE JUMP START LEADS TO THE BATTERY

1. Connect the red clamp to the unearthed battery terminal first, (this is
usually the positive (+ve) terminal and coloured RED).

2. Connect the black clamp to the earthed battery terminal, (this is usually
the negative (-ve) terminal and coloured BLACK)

3. Once you have connected the leads you have 30 seconds to try and start
the vehicle, otherwise you will need to remove the leads and reattach
them.

8

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SMART CABLE STATUS LIGHTS

STATUS Green LED Red LED Beeping

Detecting Flashing Flashing No

Ready to start Solid Off No

Low Voltage Off Solid No

High Voltage Off Solid No

Short Circuit Off Flashing Yes

Reverse Polarity Off Flashing Yes

Reverse Charge Solid Solid Yes

Over heating Off Solid Yes

No operation within 30 seconds of connecting
to the battery terminals

Solid Solid No

JUMPSTART THE VEHICLE BATTERY

CAUTION: MAKE SURE THAT THE POWER PACK IS AT LEAST 75% CHARGED
(3 POWER INDICATOR LIGHTS ARE LIT) BEFORE YOU ATTEMPT TO
JUMPSTART.

ALWAYS carry out the following preliminary checks:

• Switch off the vehicle ignition and ALL ancillary equipment (lighting,

radio etc.)

• Ensure the vehicle battery is rated at 12V and is not damaged in any

way.

• Ensure the area is well ventilated.

• Make sure that the device is at least 75% charged (3 power indicator

lights are lit).

1. Switch the ignition to ‘start’ FOR A MAXIMUM OF 6 SECONDS). If the engine
does not start within this time, SWITCH OFF the ignition and WAIT FOR AT

LEAST 3 MINUTES BEFORE TRYING AGAIN.

2. Once the engine is running, disconnect the clamps within 30 seconds,
BLACK clamp FIRST, then disconnect the RED clamp.

3. Leave the vehicle engine running for a while to let the alternator recharge
the battery.

9

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

DECLARATION OF CONFORMITY

10

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

ALSO AVAILABLE

P

lease check out our wide range of jumpstarts, automotive tools and

equiptment available from you local Clarke dealer including the following.

MODEL NUMBER PART NO

JSM300 Multifunction Micro
Jumpstart/Portable Device
Charger Power Pack

• Jumpstart output - Starting
current 300A, Peak current
500A

• Very low charge cycle
requiring only approx
6monthly recharge if not used.

• Supplied in convenient zipped
storage bag

JSM350 - Multifunction Micro
Jumpstart/ Portable Device
Charger Power Pack

• Jumpstart output - Starting
current 350A, Peak current
500A

• Very low charge cycle
requiring only approx
6monthly recharge if not used.

• Can be used approx. 20 times
on a single charge

Jumpstart 1224

• Starts petrol engines up to 6
litres and diesel engines up to
3 litres

• Includes 230V mains charger
and 12V ad

rging

cha

• Switchable dual voltage. 12V
& 24V for extra heavy duty
usage

aptor for in-vehicle

6240045

6239010

6240045

11

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]