Clarke Jetstar 1550, Jetstar 1600, Jetstar 3000, 7333000, 7333050 User guide

...
Page 1
1550 - 1600
INSTRUCTIONS
JET 3000
Part No. 7333100
and
7333000 - 7333050
Part Nos.
JETSTAR
©
0701
Page 2
© Copyright Clarke International. All rights reserved. September 1995
For Spare Parts and Service,please contact your nearest dealer, or CLARKE
SERVICE: Service@clarkeinternational.com
PARTS: Parts@clarkeinternational.com
PARTS & SERVICE FAX: 020 8558 3622
PARTS & SERVICE TEL: 020 8988 7400
International, on one of the following numbers.
SPARE PARTS & SERVICE CONTACTS
or e-mail as follows:
152
Page 3
Motor will not stop 1. Defective safety 1. Return to service agent
when trigger released. switch
Motor will not restart 1. Defective safety 1. Return to service agent.
when trigger pressed. switch
Machine will not 1. Pump sucking in air. 1. Check for leaks in hose.
come up to pressure 2. Intake filter blocked 2. Clean filter
when starting a period of storage refer to maintenance
Machine blows fuses 1. Pump seals dry after 1. Free off pump seals
electrical and water supply’s and free
Motor will not rotate 1. Pump seals dry after 1. Disconnect from
Machine will not start 1. No electrical power 1. Check cable, plug, fuse
TROUBLESHOOTING
Fault Cause Remedy
3. Defective pump 3. Return to service agent.
(Unit switched ON,
with pressure in
(Unit switched ON,
with pressure in
system)
14
system)
2. Pressures in system 2. Refer to starting
uneven procedure p6.
p8.
period of storage
seals - refer to Care &
Maintenance, page 9
2. Electrical defect 2. Return to service agent
Before assembling your new Jetstar Powerwasher, check to ensure that all
parts listed below are included.
Jetstar Powerwasher with cable and plug.
Trigger/Handle assembly with high pressure hose.
Lance with nozzle assembly.
Inlet hose connector.
Detergent/foam lance.
Detergent/foam container.
Bag containing one hex. wrench and one wire prod.
3
PRE- ASSEMBLY CHECKS
effect your statutory rights.
GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a
period of 12 months from the date of purchase. Please keep your receipt
as proof of purchase. This guarantee is invalid if the product is found to
have been abused or tampered with in any way, or not used for the
purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product
can be returned to us without prior permission. This guarantee does not
forward to it giving you long and satisfactory service.
Thank you for purchasing this CLARKE Jetstar Powerwasher.
This machine is a lightweight, portable, high pressure power washer,
designed for DIYuse.
It comprises an electric motor, a pump, a high pressure hose with a trigger
and lance, and an adaptor for injecting foam or cleaning agents into the
water jet, ideal for cleaning greasy engines and equipment, removing oil
spots from patios etc.
Before attempting to use your Jetstar, please read this instruction manual
thoroughly and follow all instructions carefully. By doing so you will ensure
the safety of yourself and that of others around you, and you can look
Page 4
17. Disconnect from the mains supply before carrying out any
18. Never carry the washer by the power cable, or yank it to disconnect
maintenance or servicing.
from the socket. Keep the cable away from heat, oil or sharp edges.
4
16. When not in use, disconnect from the water and electrical supply’s,
and ensure the system is completely drained. Store in a dry, frost free
environment.
7. Never operate the machine with any of the covers removed.
9. Never supply any liquid other than CLEAN water to the water inlet.
10. Use only chemical cleaning agents (detergents) approved for power
11. Never use the foam lance to introduce solvents eg. paint thinners,
13. Do not operate the machine whilst standing on ladders: use a platform
14. Children should not be allowed to use the machine.
15. We recommend the use of safety goggles when using machine with
washing when using the foam lance.
petrol, oil, etc.
sand blasting attachment (optional accessory - see Page 11), or any
application where loose particles of stone or grit etc. may be blown
around by the high pressure spray.
tower or scaffolding.
8. Do not, attempt any electrical or mechanical repair. If you have a
problem with your machine contact your local dealer or Clarke
Customer Services Dept., tel: 020 8988 7400
4. After use, and before disconnecting hoses, release the pressure in the
equipment.
high pressure hose by operating the trigger. Do not attempt to
disconnect any hose or coupling with pressure still in the hose.
1. Never direct the spray jet at any person or animal.
2. Never hold a finger over the high pressure nozzle.
3. Never direct the spray jet at the machine itself or any other electrical
Water at high pressure can be dangerous and may cause severe damage
NEVER allow anyone to operate this equipment unless they are thoroughly
SAFETY PRECAUTIONS
reliable, and completely familiar with the safety precautions.
to persons or property if subject to misuse.
WARNING!
The range of accessories listed below may be purchased from your CLARKE
Gross Weight 14kg 14kg 13kg
Max. Inlet Water Temp. 50°C 50°C 50°C
Max. Pressure 1200psi (82Bar) 1500psi (102Bar) 1400psi (95Bar)
Max. Water Flow 7 Litre/min 7.5 Litre/min 6.7 Litre/min
Motor 230V 50Hz 1 Ph 230V 50Hz1 Ph 230V 50Hz 1 Ph
Power Rating 1.3HP 1.6HP 1.4HP
SPECIFICATIONS
dealer.
ACCESSORIES
Item Part No.
Car Brush 7310110
Rotary Brush 7310104
Water Sandblaster 7310106
Drain Cleaner 7310117
Turbo Nozzle 7334000
Extension Hose 10M 7310120
Two Wheel Trolley 7310102
Lance Extension 7310122
5 Litres Detergent (Traffic Film Remover) 3050821
25 Litres Detergent (Traffic Film Remover) 3050820
5 Litres Wash ‘n’ Wax 3050815
Sand (For use with Sand blaster) 7320005
Jetstar 1550 Jetstar 1600 Jet 3000
13
Page 5
Part Nos. for Jet 3000 are the same as those for Jetstar 1600, except for item 5,
which has 3 components shown below, the Hex wrench, plus additional
components:
7 Axle FP52436400
8 Axle Clamps FP50148700
6 Wheel FP17807000
5C LP Water Inlet Adapter Hose Holder FP52037500
- Hex. Wrench (for turning motor) FP15609900
5B LP Water Inlet Adapter Gasket FP52037400
No. Description Part No.
5A LP Water Inlet Adapter Ring FP52037300
Jet 3000
12
If an extension cable is used, always ensure it is fully unwound. When used
outdoors, ensure the extension cable is specifically designed for outdoor use.
The maximum extension length is 25 metres. Ensure that the wire sizes in the cable
is at least 0.75mm
thicker than the cable supplied with the washer.
EXTENSION CABLES
IF IN DOUBT, CONSULT A QUALIFIED ELECTRICIAN.
Do not attempt any electrical repairs yourself.
5
2
in cross section. As a general rule, the extension cable must be
4. Replacement fuse covers can be obtained from your local dealer or most
replacement is used (as indicated by marking or colour code).
electrical stockists.
2. Never use the plug without the fuse cover fitted.
3. Should you wish to replace a detachable fuse carrier, ensure that the correct
The fuse in the plug for this appliance must be ASTA approved to BS1362. AND
rated at 13 amps
IMPORTANT:
If this appliance is fitted with a plug which is moulded onto the electric cable (i.e.
non-rewirable) :
1. The plug must be thrown away if it is cut from the electric cable. There is a
danger of electric shock if it is subsequently inserted into a socket outlet.
Residual Current Device (RCD).
FUSE RATING
Brown ............................................. Live
As the colours of the wires in the mains lead may not correspond with the coloured
markings identifying the terminals in your plug, proceed as follows:
Connect GREEN & YELLOW coloured cord to plug terminal marked with a
l etter “E” or Earth symbol “ ”.
Connect BROWN coloured cord to plug terminal marked letter “L”
Connect BLUE coloured cord to plug terminal marked letter “N”
We recommend that this machine is connected to the mains supply through a
in accordance with the following colour code:
Green & Yellow ............................. Earth
Blue ................................................ Neutral
This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for
connection to a standard, domestic electrical supply.
Should the plug need changing at any time, ensure that a plug of identical
specification is used. IMPORTANT: The wires in the mains lead should be wired up
ELECTRICAL CONNECTIONS
WARNING: THIS MACHINE MUST BE EARTHED.
Page 6
2. Hose, worm drive clips and other accessories are readily available
from all good DIY, Hardware and Garden Supplies Stores.
the disposal of possibly contaminated water.
local bylaws concerning the use of water from the mains supply, and
6
2. Check to ensure that the filter is correctly located inside the inlet connection.
1. In some areas, it may be necessary to ensure that you comply with
(not supplied) CLEAN, cold or hot water (up to 50°C) can be used.
NOTE:
Screw on the inlet connector, with hose attached, to the water inlet. This
connection must be tight to avoid leaks.
Secure the other end of the hose to your tap using a suitable tap adaptor
1. Use a good quality hose of at least 1/2" (13 mm) diameter.
Remove the temporary travel cap from the threaded inlet connection
and ensure that the sealing ring is in place.
The water inlet on the Jetstar 1550 and 1600 models is on the left front of the
unit, on the Jet 3000 model it is mounted on the bottom left - handle end.
Attach a suitable hose to the inlet hose connector, and secure with a
worm drive clip, (hose and worm drive clip are not supplied).
NOTE:
C. Water Supply Hose
vaseline or similar, will assist when joining the parts together.
home firmly and twist to lock it in position. Twist anticlockwise looking down
from the handle end. DO NOT attempt to disassemble the lance.
NOTE: When new, the lance may be a tight fit and a little lubrication, with
At the opposite end to the nozzle is a a spigot with two integral lugs, and
a rubber O-ring. Ensure the O-ring is in place and in good condition.
Insert the spigot end of the lance into the trigger/handle assembly. Push
end to power cable inlet, on the Jet 3000 model, it is mounted on the front -
handle end.
B. Lance
Remove the plastic travel cap from the threaded high pressure outlet,
and screw on the high pressure hose firmly.
The outlet on the Jetstar 1550 and 1600 models is at the front of the unit - opposite
ASSEMBLY AND PREPARATION FOR USE.
A. High Pressure Hose
- Hex. Wrench (for turning motor) FP15607000 FP15607000
- Water Inlet Filter FP52066500 FP52066500
5 LP Water Inlet Adapter c/w O-Ring
4 Detergent Bottle FP15603400 FP15603400
- Detergent Bottle Cap FP15603401 FP15603401
2 Lance Assembly FP60710100 FP60710000
3 Detergent Lance c/w plastic tube FP60603800 FP60603800
No. Description Part No. Part No.
1 High Press. Hose c/wHandle Assy FP60600107.88 FP60600107.88
PARTS LISTS & DIAGRAMS
and Rubber Washer FP18106400 FP18106400
Jetstar 1550 & Jetstar1600
11
Jetstar 1550 Jetstar1600
Page 7
Located behind the water inlet, this filter should be removed for cleaning
after every 10 hours of use (or less if water is contaminated).
Remove the filter by unscrewing the input hose connection and
withdrawing the filter element.
Clean the element with fresh water. To replace, reverse the above
procedure, ensuring that all seals are in place.
correct procedure for starting.
located on the front of the machine.
Once the hex wrench is engaged, turn the
motor to free the seals. When the motor
turns freely, withdraw the hex. wrench,
(reassemble the cover in the case of the
Jet 3000), reconnect the electrical and
water supply’s, and go through the
It will be necessary to remove the top
cover by removing the 7 screws from
beneath the machine as indicated in Fig.
2. This will give easy access to the hex.
socket on the rear of the motor, which is
visible through the hole.
Thread the hex. wrench (supplied), through the
hole in the cover, at the centre of the rear of
the unit, (see Fig.1), and into the hex. socket
mounted on the rear of the motor, which is
Water input filter
10
6
45
2
3
B. JET 3000
1
A JETSTAR 1550 and 1600
7
and allowing the pump to develop full pressure.
You may release the trigger once full pressure is developed. When you do so, a
safety switch will cut IN turning the motor OFF. This prevents the possibility of damage
to the motor, which could occur should it be left to run with pressure in the system
(ie. without pulling the trigger), for a period of time.
As soon as you pull the trigger again, the motor will cut in and water at pressure
As explained above, whenever you release the trigger, the motor will automatically
stop, conserving energy and reducing pump and motor wear. It will cut in again
when the trigger is pulled. This process will continue for as long as the machine is
switched ON.
In the event that you switch the machine OFF, but intend to continue with its use
after a few minutes or so, DO NOT depress the trigger, but set the safety latch to
prevent it from being accidentally pulled. This will ease and assist the subsequent
restarting of the motor as pressures will remain equalised on either side of the
pump, thereby reducing the load on the motor when restarting.
NEVER attempt to run the machine with the water supply disconnected, or turned
off
firmly. In addition, care must be taken to ensure that the nozzle is NOT aimed
animals, windows - greenhouses etc., and be aware that splash back could
at an area where the water jet will cause damage. i.e. away from people,
also cause damage if the jet is trained on a nearby wall etc.
7
Ensure the operator is aware that when the trigger is pulled, water at high
pressure can cause the lance to kick fiercly - it should therefore be held
will be ejected.
WARNING!
Fig. 2
On the Jetstar 1550 and 1600 models, the switch is a rotary type mounted on the
left side front of the unit. On the Jet 3000 it is a rocker type mounted on top.
NOTE: Do not operate the Jet 3000 in an upright position - it must rest on its’ wheels.
Connect the plug to the mains supply, preferably via a Residual Current Device.
Turn the water tap fully on.
When starting, it is IMPORTANT that you adopt the following procedure:
In order to ease the starting process, and to prevent the possibility of blown fuses,
pull the trigger on the lance - it may be necessary to release the safety latch in
order to do so, and hold the trigger in that position whilst switching the motor ON
Fig. 1
Make certain the ON/OFF switch is set in the OFF position.
OPERATION
Page 8
A high pressure jet or fan spray may be used. A fan spray is achieved by turning
attaching to the handle.
Spray the detergent on to the vehicle, patio etc., and allow it to work itself into the
grime.
To rinse and clean, set the safety latch, replace the detergent lance with the main
lance, release the safety latch and blast off the dirt.
After using the detergent lance, rinse it, together with the container, thoroughly
with clean water.
IMPORTANT: Ensure you read and comply with the manufacturers instructions
regarding the use of chemical detergents.
8
the plastic pickup tube is in place.
NOTE: It may be necessary to lubricate the lance spigot when new to assist when
down from the handle end, and pulling it free.
Insert the detergent lance, push in firmly and twist anticlockwise to lock in position.
With the container filled with detergent, screw it on to the detergent lance ensuring
To prepare for detergent application, ensure the trigger safety latch is set to prevent
the trigger from being pulled accidentally.
Remove the lance from the trigger/handle assembly by twisting it clockwise looking
detergents recommended for use with power washers, such as CLARKE Traffic Film
Remover which is a powerful low foaming agent for car cleaning, patio cleaning
etc., or CLARKE Wash & Wax, both available from your CLARKE dealer.
To improve cleaning qualities, it is possible to introduce chemical cleaning agents
(detergents) into the spray using the foam lance. This is particularly useful for washing
cars, greasy engine parts, removing oil spots on concrete etc. Use ONLY those
Chemical Cleaning Agents
the nozzle as shown below.
water supply’s, and proceed to free them as follows:
If the seals are stuck however, disconnect the machine from the electrical and
body, as described above.
problem may be alleviated by storing the machine with antifreeze within the pump
possible that the seals within the pump have dried out and are gripping the pistons. This
If you experience difficulty in starting the motor following a long period of storage, it is
within the pump body.
NOTE:
the machine and allow the antifreeze to
circulate. After a short time stop the
machine, and store with the antifreeze still
If there is a danger of freezing, insert the
inlet and outlet hoses into a bucket of
antifreeze as shown in the diagram, start
Store the Jetstar 1550 and 1600 washer in
an horizontal postion. The Jet 3000 may
be stored upright.
Storage
9
antifreeze
containing
Bucket
If cleaning agents have been used, thoroughly clean the detergent lance and
bottle with clean water.
After each use
Ensure the plug is removed from the socket before carrying out any
adjustment, servicing or maintenance.
WARNING:
CARE AND MAINTENANCE
by twisting it clockwise (looking down from the handle end), and pulling the lance
free. The accessory can then be connected to the handle assembly in a similar
manner to the lance.
Your Jet Star power washer can be used with a wide range of optional accessories
available from your local dealer (see page 11 for a full list ).
To use the accessories you must first remove the lance from the handle assembly
ACCESSORIES
Loading...