Clarke JET 9000 Operation & Maintenance Instructions Manual

WARNING: Do not use the machine without reading this manual

OPERATION & MAINTENANCE

INSTRUCTIONS

GC0913

POWER WASHER

MODEL NO: JET 9000

PART NO: 7333502

2

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

INTRODUCTION

Thank you for purchasing this CLARKE Power Washer.

The machine has been designed to use hot or cold water to clean any
surfaces which can stand the force of the high pressure water jet and the
action of the detergents used.

The machine must only be used for the purpose for which it was designed.

Before attempting to use this product, please read this manual thoroughly and
follow the instructions carefully. In doing so you will ensure the safety of yourself
and that of others around you, and you can look forward to your purchase
giving you long and satisfactory service.

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

3

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

GENERAL SAFETY RULES

1. High pressure water jets can be dangerous if subject to misuse. They must
not be directed at animals or people.

2. NEVER allow children or untrained personnel to use this product.

3. NEVER operate the power washer with any covers removed.

4. NEVER attempt any electrical or mechanical repairs to this power washer.
Always refer to your Clarke dealer.

5. NEVER supply any liquid other than water to the water inlet.

6. Never use the detergent facility to introduce flammable liquids/solvents,
e.g. paint thinners, petrol, oil due to risk of explosion.

7. ALWAYS release any residual pressure in the machine by turning off the
water supply and operating the trigger, before disconnecting the hose.

8. ALWAYS keep the pressure washer itself dry and clear of water spray.

9. Never direct the spray jet at the pressure washer itself or any other
electrical equipment.

10. ALWAYS wear protective clothing, safety shoes and safety glasses. Loose
particles & other debris may be propelled at high speed by the water jet.

11. ALWAYS hold the spray gun firmly & expect the gun to ‘kick’ when starting.

12. ALWAYS disconnect from the water supply and ensure the machne is
completely drained when not in use. Store in a cool dry location.

13. Only use chemical cleaning agents (detergents), that are approved for
pressure washers. CLARKE Traffic Film Remover or CLARKE Wash and Wax
(available from your dealer), are recommended.

14. ALWAYS disconnect from the electrical power supply and remove the plug
from the socket before carrying out any maintenance.

15. ONLY use original spare parts from the Clarke service department.

16.High pressure hoses, fittings and couplings are important for the
safety of the machine. Use only hoses, fittings and couplings
recommended by the manufacturer.

17. NEVER use the pressure washer if the power cable or other
important parts of the power washer are damaged.

18.If an extension cable is used, the cable and plug must be of
watertight construction. Inadequate extension cables can be
dangerous.

WARNING: WATER AT HIGH PRESSURE CAN BE DANGEROUS AND CAN
CAUSE DAMAGE IF THE OPERATOR IS CARELESS. NEVER ALLOW ANYONE
TO OPERATE THIS MACHINE UNLESS THEY ARE FAMILIAR WITH THE SAFETY
PRECAUTIONS.

4

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SAFETY SYMBOLS

The following symbols are displayed on
the machine.

WAR NI NG : Do not discharge the water
spray at persons or animals. Keep clear
of nozzle.

WAR NI NG : Never direct spray toward
any electrical device or electrical
outlet.

Read Instructions

Wear Eye Protection

Wear Hand Protective Gloves

Falls within the WEE (Waste Electrical/
Electronic) Directive

5

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

ELECTRICAL CONNECTIONS

Before switching the product on, make sure that the voltage of your electricity supply is
the same as that indicated on the rating plate. This product is designed to operate on
230VAC 50Hz. Connecting it to any other power source may cause damage.

This product may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in the plug, the fuse cover must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a suitable replacement is obtained.

If the plug has to be changed because it is not suitable for your socket, or due to
damage, it should be cut off and a replacement fitted, following the wiring instructions
shown below. The old plug must be disposed of safely, as insertion into a mains socket
could cause an electrical hazard.

• The wire which is coloured Blue must be connected to the terminal which is

marked N or coloured Black.

• The wire which is coloured Brown must be connected to the terminal which is

marked L or coloured Red.

• The wire which is coloured Yellow and Green must be connected to the

terminal which is marked E ( ) or coloured Green.

WE STRONGLY RECOMMEND THAT THIS MACHINE IS CONNECTED TO THE MAINS SUPPLY VIA A
RESIDUAL CURRENT DEVICE (RCD)

If in any doubt, consult a qualified electrician. DO NOT attempt any repairs yourself.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS
THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS
SUPPLY.

WARNING: THE WIRES IN THE POWER CABLE OF THIS PRODUCT ARE
COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:
BLUE = NEUTRAL BROWN = LIVE YELLOW AND GREEN = EARTH

Plug must be BS1363/A approved.

Always fit a 13 Amp fuse.

Ensure that the outer sheath of the cable is firmly held by the clamp

Neutral

(Blue)

Live

(Brown)

Earth

(Green and Yellow)

6

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

OVERVIEW

1 On/OFF Switch 5 Detergent Container

2 Spray Gun Assembly 6 Power Cable

3 Reel Handle 7 Mains Water Inlet

4Lance

7

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

LIST OF CONTENTS

The following items should be supplied in the carton. If any parts are missing or
damaged, please see your Clarke dealer where you purchased the machine.

BEFORE USE

Unpack your power washer and check to ensure all the items listed above are
present.

UNFOLDING THE HOSE REEL HANDLE

1. Open the reel handle from its
folded position before use.

2. Release the hose from the
retaining clip on the hose reel,
then pull the hose from the reel to
unwind whatever length is
required.

• Winding the handle clockwise

will reduce the length of the
hose.

• If the spray gun/lance assembly is not attached, the hose can be

secured in the retaining clip when the hose is re-wound.

1 x Power Washer

1 x Gun Assembly

1 x Lance c/w fitted Pencil-Jet / Fan - High / Low Nozzle

1 x Hose Assembly on integral Hose-Reel

1 x Inlet Hose Adaptor

1 x Instruction Manual

1 x Accessory Adaptor

8

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

ASSEMBLING THE LANCE

The lance must be fitted to the gun
assembly before use.

1. Assemble by screwing the end of
the lance into the gun assembly.

2. Tighten the locking nut using a 22
mm spanner.

3. Slide the plastic cap into position.

CONNECTING THE GUN TO THE HOSE

Connect the gun to the hose by
screwing on the connector and
tightening with a 17 mm spanner.

CONNECTING THE MAINS WATER SUPPLY

NOTE: Always follow any regulations of

your local water supplier.

1. Screw the inlet adaptor to the
water inlet as shown.

2. Connect the mains water supply
hose to the inlet adaptor. A
standard garden hose is suitable.

• It is recommended to use a

reinforced hose with an inner
diameter of at least 10 mm
available from your CLARKE
dealer.

• Ensure the water connection is secure.

NOTE: The water source must provide

a minimum of 6.6 litres per minute
at not more than 40°C.

9

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

FILLING WITH DETERGENT

If you intend to use detergent:

1. Remove the detergent filler cap
located at the rear of the pressure
washer and fill with detergent.

2. Replace cap before use.

3. Only use detergents
recommended for use with
pressure washers, such as CLARKE
Traffic Film Remover which is a
powerful ‘low foaming’ agent for
car cleaning, patio cleaning etc., or CLARKE Wash & Wax, both available
from your CLARKE dealer.

The use of unsuitable cleaning agents may adversely affect the safety of the
machine. Before use, refer to correct operating temperatures on page 17.

ACCESSORIES

A range of accessories is available from your Clarke dealer including:

• Accessories with bayonet style couplings such as those shown can be

fitted to the hose by means of the adaptor supplied.

DESCRIPTION SIZE PART NUMBER

Car Wash & Wax Shampoo 5 Litre 3050815

Concentrated Traffic Film Remover 5 Litre 3050821

Concentrated Traffic Film Remover 25 Litre 3050820

Ready To Use Traffic Film Remover 5 Litre 3050818

Ready To Use Traffic Film Remover 25 Litre 3050819

10

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

OPERATION

GETTING STARTED

1. Ensure that the water supply is correctly connected and turned on.

2. Plug the power cable into the
mains supply.

3. Release the trigger lock.

• The pressure washer is now

ready for use.

4. Press the start switch (‘I’).

5. Pull the trigger.

NOTE: When the trigger is pulled the

pressure of water will cause
the lance/gun assembly to
kick back suddenly.

6. When using the power washer for
the first time, let it run for a few
moments so that any air bubbles
or other impurities are discharged.

7. Release the trigger to stop the water flow.

• This pressure washer is fitted with an auto stop system to protect the

motor during use.

• When the trigger is released, the motor will stop. When the trigger is

squeezed the motor will start up again.

WARNING: FAILURE TO TURN ON THE WATER FULLY COULD CAUSE
DAMAGE TO THE POWER WASHER INTERNAL COMPONENTS.

WARNING: DO NOT USE THE POWER WASHER IF THE SUPPLY CABLE OR
IMPORTANT PARTS OF THE MACHINE ARE DAMAGED, E.G. SAFETY
DEVICES, HIGH PRESSURE HOSES, TRIGGER.

WARNING: WE RECOMMEND THAT THIS MACHINE IS CONNECTED TO THE
MAINS SUPPLY VIA A RESIDUAL CURRENT DEVICE (RCD).

11

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

ADJUSTING THE SPRAY

The nozzle is adjustable to allow you to adjust the spray from a narrow jet of
water to a wide spray.

To adjust the nozzle, proceed as
follows:

1. Hold the shaft of the lance in one
hand.

2. Twist the nozzle with the other
hand.

3. To vary the spray between narrow
and wide, turn the nozzle

anticlockwise through 180

o

.

ADJUSTING THE PRESSURE

There are three ways to adjust the
pressure of the water:

1. Slide the nozzle forwards to lower
the pressure.

2. Back away from the surface
being cleaned. The further away
you are the less the pressure will
be on the surface being cleaned.

3. Adjust the spray to a wider angle.

APPLYING CHEMICALS AND CLEANING SOLVENTS

1. Ensure the trigger is locked.

2. Remove the cap from the detergent container.

3. Fill the container with a suitable bio-degradable detergent.

4. Replace the cap.

5. Squeeze the trigger.

6. Pull the adjusting sleeve forward to set the required spray pressure.

7. Start washing.

CAUTION: IF YOUR EYES COME INTO CONTACT WITH ANY CLEANING
FLUIDS, RINSE THEM IMMEDIATELY WITH PLENTY OF FRESH, CLEAN WATER
AND SEEK MEDICAL ADVICE IF REQUIRED.

12

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SHUTTING DOWN

When you have finished using the
power washer, follow the procedure
below to switch off and disconnect
the unit:

1. Press the stop switch (‘O’).

2. Turn the mains water supply off at
the tap.

• NEVER turn the water off with

the power washer running.

3. Release the pressure in the pump and hose by squeezing the trigger for a
few seconds until no more water comes out of the nozzle.

4. Move the trigger lock to the locked position.

5. Disconnect the mains power
supply and store the cable in its
position on the rear of the
machine.

6. Wind the hose onto the reel and
store the spray gun/lance in the
holder on the front of the power
washer as shown on page 6.

13

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

MAINTENANCE

CLEANING THE NOZZLE

If the nozzle becomes partially clogged with foreign material such as dirt or
limescale, excessive pressure may develop and the pump pressure will
pulsate. Clean the nozzle immediately as follows:

1. Turn off the power washer and turn off the water supply.

2. Pull the trigger to relieve any water pressure.

3. Disconnect the lance from the spray gun.

4. Remove any obstructions by directing water supply into the end of the
lance for 30 seconds to back flush loose particles.

5. Reconnect the lance to gun and turn on water supply.

REMOVING THE SPRAY GUN FROM THE HOSE

The gun can be disconnected from the hose for cleaning or to unblock the
spray gun/hose by disconnecting the connection using a 17 mm spanner.

Pull the hose away from the spray gun.

CLEANING THE WATER INLET FILTER

This filter should be checked periodically and cleaned if necessary.

1. Remove filter from the water inlet
of the pump as shown.

2. Clean the filter by flushing both
sides with water.

3. Replace the filter into the water
inlet.

• The tapered side faces inwards.

NOTE: Do not operate power

washer without filter properly
installed.

WARNING: THE MACHINE SHALL BE DISCONNECTED FROM THE POWER
SUPPLY BY REMOVING THE PLUG DURING CLEANING OR MAINTENANCE
AND WHEN REPLACING PARTS.

14

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SERVICING

All repairs and maintenance operations must be carried out by technically
qualified personnel while disconnected from the power and water supplies.

Correct use and maintenance is necessary to guarantee the power washer's
reliability and best performance.

Please only use the correct spare parts as supplied by your Clarke dealer.

ANNUALLY

LIMESCALE

Periodically the pump should be checked for limescale buildup, dependant
upon the hardness of the local water supply.

Please contact the CLARKE International Service Dept.

DE-COMMISSIONING THE PRODUCT

Should the product become completely unserviceable and
require disposal, dispose of the product according to local
regulations. Recycle unwanted materials instead of disposing of
them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner
which is compatible with the environment.

STORING THE POWER WASHER

1. Disconnect the high pressure hose and drain all water from the hose.

2. Make sure that the power washer has been thoroughly cleaned before
storing it in a clean dry place.

3. Avoid storing the power washer at freezing temperatures.

15

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

No water delivery. Water filter blocked. See cleaning the water filter

on page 13.

Pump valves jammed. Contact Clarke Service

Department.

Clogged lance nozzle. Clean the nozzle.

Low or irregular
pressure

Insufficient water supply. Check connections.

Pump taking in air. Check connections.

Detergent inlet sucking in
air.

Check connections and
that detergent supply is
topped up.

Water filter dirty. Clean or replace.

Worn out gaskets or valve
components.

Contact Clarke Service
Department for
replacement.

Exceeding the inlet water
temperature.

Make sure the water supply
is below 60 degrees.

Damaged or warn out
nozzle components.

Contact Clarke Service
Department for
replacement.

Low Voltage. Make sure the pressure

washer is connected to a
suitable power supply.

Machine is noisy. Air intake worn out / dirty/

blocked valves. Excess
water temperature.

Check air inlet. Contact
Clarke Service Department.
Reduce water temperature.

Motor suddenly
stops.

Thermal protection has
activated due to
overheating.

Switch off the machine and
wait until the unit has cooled
down sufficiently.

Pressure drop. Air in system

. Bleed system by quickly

operating trigger several
times. If necessary operate
the machine briefly without
the high pressure hose
connected.

Worn high pressure nozzle

. Renew nozzle.

16

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

Pressure
fluctuations or
pressure drop.

Shortage of water. Turn water tap on fully.

Water supply hose too long/
too narrow.

Use a 1/2” diameter water
supply hose.

No water due to clogged
inlet filter.

Clean water inlet filter.

Oil leak. Worn seals. Contact your Clarke dealer.

Motor does not
start when
switched on.

Plug is not connected
properly.

Check plug and lead and
have them replaced by a
qualified electrician if
necessary.

Mains fuse tripped/blown. Renew fuse or reset.

Motor hums when
trigger operated
and does not start.

Mains voltage too low. Have electrical connection

checked.

Incorrect diameter cable
resulting in voltage drop.

Use correct diameter cable.

Pump seals stuck. Contact your Clarke dealer.

Motor cuts out ­trigger open.

Motor protection switch has
been activated due to
overheating or motor
overload.

Ensure supply voltage and
unit voltage are equal.
Switch off and allow to cool
for at least three minutes.

Nozzle partly clogged. Clean using the supplied

nozzle cleaning needle.

Additives are not
being supplied.

Additive container empty. Fill additive container.

Lance not correctly set. Put lance on low pressure

setting.

17

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

PRODUCT SPECIFICATIONS

CONSUMABLES

A range of suitable hose, shampoo and traffic film remover are available from
your Clarke dealer.

Model Number JET 9000

Part Number 7333502

Voltage 230V/50Hz

Motor Input Power 2600 W

Duty Cycle Continuous

Working pressure 123 bar

Maximum pump output pressure 200 bar

Maximum output flow rate 7.75 l/min (465 l/hr)

Maximum output temperature

40

0

C (1040F)

Maximum input temperature

0-40

0

C

Detergent tank capacity 2200 ml

Sound Pressure Level (LWA)81

Sound power level (L

WA

)94

Guaranteed sound power level (L

WA

)98

Uncertainty Factor K 3.44

Dimensions (L x W x H) 305 x 328 x 806 mm

Weight 23.65 kg

18

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

PARTS LIST - FRAME & BODY

POS DESCRIPTION CODE POS DESCRIPTION CODE

1 Self-tapping Screw TMC9000FB01 17 Pump Assembly TMC9000FB17

2 Handle Pin TMC9000FB02 18 Front Cover TMC9000FB18

3 Hose Reel TMC9000FB03 19 Handle TMC9000FB19

4 Self-tapping Screw TMC9000FB04 20 Cable Sleeve TMC9000FB20

5 Cable Hook TMC9000FB05 21 Switch Holder TMC9000FB21

6 Cap Screw TMC9000FB06 22 Switch Panel TMC9000FB22

7 Spring Gasket TMC9000FB07 23 Power Switch TMC9000FB23

8 Flat Gasket TMC9000FB08 24 Air Outlet TMC9000FB24

9 Base TMC9000FB09 25 Self-tapping Screw TMC9000FB25

10 Container Cap TMC9000FB10 26 Cable Retainer TMC9000FB26

11 Container TMC9000FB11 27 Cable Gland TMC9000FB27

12 Container Retainer TMC9000FB12 28 Board Clip TMC9000FB28

13 Capacitor Clamp TMC9000FB13 29 Spring Clip TMC9000FB29

14 Wheel TMC9000FB14 30 Insulation Sleeve TMC9000FB30

15 Wheel Retainer TMC9000FB15 31 Power Cable TMC9000FB31

16 Wheel Cover TMC9000FB16 32 Spray Gun & Lance TMC9000FB32

19

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

PARTS LIST - INTERNAL COMPONENTS

20

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

PARTS LIST - INTERNAL COMPONENTS

POS DESCRIPTION CODE POS DESCRIPTION CODE

1 Motor Winding Cover TMC900001 27 Relief Valve TMC900027

2 Motor Fan TMC900002 27-1 Sealing Ring TMC9000271

3 Induction Motor TMC900003 27-2 Relief Valve Piston TMC9000272

4 Terminal Box TMC900004 27-3 Sealing Ring TMC9000273

5 Capacitor/wire TMC900005 27-4 Relief Valve Support TMC9000274

5-1 Capacitor/wire TMC9000051 27-5 Relief Valve Spring TMC9000275

5-2 Insulation Sleeve TMC9000052 27-6 Sealing Ring TMC9000276

5-3 Clip TMC9000053 27-7 Valve Seat Cover TMC9000277

6 Main Switch Wire TMC900006 27-8 Valve Connect Screw TMC9000278

6-1 Main Switch Wire TMC9000061 27-9 Safety Valve Stem TMC9000279

6-2 Insert Spring TMC9000062 27-10 Auto Stop Spring TMC90002710

6-3 Earth Terminal TMC9000063 27-11 Spring Press TMC90002711

7 Washer TMC900007 27-12 Sealing Ring TMC90002712

8 Spring Washer TMC900008 27-13 Relief Valve Bonnet TMC90002713

9 Self tapping Screw TMC900009 27-14 Switch Box TMC90002714

10 Termianl Box Cap TMC900010 27-15 Contact Point TMC90002715

11 Cam TMC900011 27-16 Micro Switch TMC90002716

12 Spring Washer TMC900012 27-17 Micro Switch Wire TMC90002717

13 Hex Screw TMC900013 27-18 Insert Spring TMC90002718

14 Washer TMC900014 27-19 Insulation Sleeve TMC90002719

15 Needle Bearing TMC900015 27-20 Switch Box Cover TMC90002720

16 Bearing Washer TMC900016 27-21 Self Tapping Screw TMC90002721

17 Spring Seat TMC900017 27-22 Sealing Ring TMC90002722

18 Plunger TMC900018 27-23 Relief Valve Bonnet TMC90002723

19 Plunger Spring TMC900019 28 Valve Body TMC900028

20 Seal Ring TMC900020 29 Oil Seal TMC900029

21 Seal Ring TMC900021 30 Guide TMC900030

22 Inlet Connector TMC900022 31 Water Seal TMC900031

23 Inlet Connector Seal TMC900023 32 Spring Washer TMC900032

24 Filter Core TMC900024 33 Hex Screw TMC900033

25 Inlet Hose TMC900025 42 Main Valve TMC900042

26 Sealing Ring TMC900026 42-1 Main Valve Cover TMC9000421

21

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

34 Hex Screw Insert TMC900034 42-2 Main Valve Seat TMC9000422

35 Pump TMC900035 43 Hose TMC900043

36 Spring Washer TMC900036 44 Nozzle TMC900044

37 Hex Screw TMC900037 45 Outlet Connector TMC900045

38 Hex Screw TMC900038 46 Hex Screw Insert TMC900046

39 Sealing Ring TMC900039 47 Spring TMC900047

40 One-way Valve TMC900040 48 Steel Ball TMC900048

40-1 One-way Valve Cover TMC9000401 49 Sealing Ring TMC900049

40-2 One-way Valve Core TMC9000402 50 Sealing Ring TMC900050

40-3 One-way Valve Spring TMC9000403 51 Suction Connector TMC900051

40-4 One-way Valve Seat TMC9000404 52 Sealing Ring TMC900052

41 One-way Valve Insert TMC900041

22

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

HOSE REEL ASSEMBLY

No DESCRIPTION CODE No DESCRIPTION CODE

1 Screw TMC9000HOSE01 8 Seal Ring TMC9000HOSE08

2 Crank Handle TMC9000HOSE02 9 Seal Ring TMC9000HOSE09

3 Bolt TMC9000HOSE03 10 Hose Spool (L/H) TMC9000HOSE10

4 Crank Handle

Hub

TMC9000HOSE04 11 Support Bracket TMC9000HOSE11

5Support

Bracket

TMC9000HOSE05 12 HP Hose

Connector

TMC9000HOSE12

6 Hose Spool

(right)

TMC9000HOSE06 13 Retaining Clip TMC9000HOSE13

7 High Pressure

Hose

TMC9000HOSE07 14 Cover Plug TMC9000HOSE14

No DESCRIPTION CODE No DESCRIPTION CODE

1 Lance Assy TMCFQ301 3 Adaptor TMC9000ADAPTOR

2 Gun Assembly TMCFQ302

23

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

DECLARATION OF CONFORMITY