Clarke HDT855, HDT1200, HDT1830 HDB1830, HDT2440 User guide

FOLDING TABLES

MODEL NO: HDT855, HDT1200, HDT1830

HDB1830 & HDT2440

ASSEMBLY INSTRUCTIONS

ORIGINAL INSTRUCTIONS GC0421 - rev 1

INTRODUCTION

Thank you for purchasing this CLARKE product. Before using this product,
please read this manual thoroughly and follow the instructions carefully. In
doing so you will ensure the safety of yourself and that of others around you,
and you can look forward to your purchase giving you long and satisfactory
service.

ENVIRONMENTAL PROTECTION

Do not dispose of this product or any unwanted materials with general
household waste. All accessories and packaging should be sorted, taken to a
recycling centre and disposed of in a manner which is compatable with the
environment.

MODEL SPECIFICATIONS

Model
Number

HDT855 3501035 867 x 867 x 739 9.4 kg 125kg

HDT1200 3501030 1225 x 613 x 735 9.25 kg 125kg

HDT1830 3501000 1830 x 760 x 740 16.4 kg 160kg

HDB1830 3501020 1830 x 250 x 400 8.15 kg 160kg

HDT2440 3501005 2440 x 760 x 740 21.4 kg 160kg

Part No Dimensions

(LxWxH) mm

Weight Max load

capacity

GUARANTEE

This product is guaranteed against faulty manufacture for a period of 12
months from the date of purchase. Please keep your receipt which will be
required as proof of purchase.

This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.

Faulty goods should be returned to their place of purchase, no product can
be returned to us without prior permission.

This guarantee does not effect your statutory rights.

2

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

SAFETY PRECAUTIONS

Failure to heed these warnings could result in personal injury or property
damage.

1. Do not exceed the load capacity of the table. (Maximum load in spec).

2. Do not stand on the table. Falling could result in personnal injury.

3. Do not put hot dishes or items (over 100

4. Do not position close to naked flames or sources of ignition.

CAUTION: TAKE CARE NOT TO PINCH YOUR FINGERS BETWEEN THE
HINGED ARM COMPONENTS WHERE SHOWN IN FIG 2.

o

C) directly on the table.

USING THE 855 TABLE

1. Lay the top face down on a soft
surface to protect the top from
scratches.

2. Unfold the legs completely by
placing one foot on the table as
shown and pulling the legs towards
you as in Fig 1.

3. Pull the legs until they form a right
angle with the table top.

4. Ensure that the arms are straight
and that locking tabs engage with
the slots in the corresponding arm
member as shown in Fig 2.

5. When folding the table away, the
legs, which are retained by the
spring clip must be folded last, as
these will retain the first pair of legs
as in Fig 3.

6. Store the table on its side – avoid
laying flat, or under heavy
pressure.

3

Parts & Service: 020 8988 7400 / E-mail: [e-mail] or [e-mail]

USING THE 1200 TABLE

1. Lay the table with the legs up and
completely unfold them.

2. Pull the legs until they form a right
angle with the table top before
turning the table over.

3. Ensure that the metal rings slide
down into position as in Fig 4, to
prevent the hinged leg assemblies
from folding up inadvertently.

4. When folding away, ensure the
legs are retained by the spring
clips shown in Fig 5.

5. Store the table on its side – avoid
laying flat, or under heavy
pressure.

UNFOLDING THE HDT1830/HDT2440 TABLES AND HDB1830 BENCH

1. Use the hand grips at each end to
unfold the table to its full extent
before standing upright. The help
of an assistant may be useful.
Unfold and lock the legs as in Fig 4.

2. When folding away, snap the
spring clips into the oppsite side of
the table to secure in the folded
position. Always carry using the
handle provided.