Page 1
Thank you for purchasing this CLARKE Multi Shelf Unit.
Please read this leaflet thoroughly before assembly to familiarise yourself with
the components. In doing so you will ensure it is correctly assembled and you
can then look forward to it giving you long and satisfactory service.
It is not recommended that the shelf unit is used in damp conditions, as this
could ultimately weaken the chipboard shelves.
Always load the shelves evenly
This CLARKE product is guaranteed against faulty manufacture for a
period of 12 months from the date of purchase. Please keep your
receipt as proof of purchase. This guarantee is invalid if the product is
found to have been abused or tampered with in any way, or not used
for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product
can be returned to us without prior permission. This guarantee does
not effect your statutory rights.
Model No CSL5400
SHELF UNIT
Hemnall Street, Epping, Essex, CM16 4LG. Tel: 01992 565300
GUARANTEE
not effect your statutory rights.
Hemnall Street, Epping, Essex, CM16 4LG. Tel: 01992 565300
Thank you for purchasing this CLARKE Multi Shelf Unit.
Please read this leaflet thoroughly before assembly to familiarise yourself with
the components. In doing so you will ensure it is correctly assembled and you
can then look forward to it giving you long and satisfactory service.
It is not recommended that the shelf unit is used in damp conditions, as this
could ultimately weaken the chipboard shelves.
Always load the shelves evenly
This CLARKE product is guaranteed against faulty manufacture for a
period of 12 months from the date of purchase. Please keep your
receipt as proof of purchase. This guarantee is invalid if the product is
found to have been abused or tampered with in any way, or not used
for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product
can be returned to us without prior permission. This guarantee does
Model No CSL5400
SHELF UNIT
GUARANTEE
Page 2
Select the next shelf
position and assemble
as with bottom shelf,
again ensure shelf is
fitted before continuing
with the third shelf
position.
Assemble the third and
subsequent shelves in the same
manner.
them from pulling out
again.
Install bottom shelf
before going any
further.
When all four beams are fitted, attach the
centre support (4).
With the tabs fully engaged in their
housings in the front/rear beams,
carefully using a flat
bladed screwdriver,
lever out the tabs
sufficiently, to prevent
The shelf rests should be uppermost.
versatility.
The shelves are manufactured from 10mm thick, high density chipboard.
These Clarke Shelf Units require no screws or fixings for assembly, providing easy
and rapid installation - and reconfiguration when required.
The steel frame allows for shelf height adjustment every 39mm, providing excellent
Lay out and identify all components.
It is necessary to bend the tabs at the ends of the five centre supports item 4 at
right angles prior to any assembly. This is carried out by inserting the tab fully into
the tab housing in one of the front/rear beams (3), and bending it at right angles
as shown in the illustration below.
Attach the bottom front/rear beams (3) and side beams (2) to the uprights (1) at
an appropriate height. Using a mallet and piece of wood, as shown , gently tap
them home.
The MAXIMUM safe working load of each shelf is 265kg
Select the next shelf
position and assemble
as with bottom shelf,
again ensure shelf is
fitted before continuing
with the third shelf
position.
Assemble the third and
subsequent shelves in the same
manner.
them from pulling out
again.
Install bottom shelf
before going any
further.
When all four beams are fitted, attach the
centre support (4).
With the tabs fully engaged in their
housings in the front/rear beams,
carefully using a flat
bladed screwdriver,
lever out the tabs
sufficiently, to prevent
ASSEMBLY
CAUTION!
Lay out and identify all components.
It is necessary to bend the tabs at the ends of the five centre supports item 4 at
right angles prior to any assembly. This is carried out by inserting the tab fully into
the tab housing in one of the front/rear beams (3), and bending it at right angles
as shown in the illustration below.
Attach the bottom front/rear beams (3) and side beams (2) to the uprights (1) at
an appropriate height. Using a mallet and piece of wood, as shown , gently tap
them home.
The shelf rests should be uppermost.
versatility.
The shelves are manufactured from 10mm thick, high density chipboard.
These Clarke Shelf Units require no screws or fixings for assembly, providing easy
and rapid installation - and reconfiguration when required.
The steel frame allows for shelf height adjustment every 39mm, providing excellent
The MAXIMUM safe working load of each shelf is 265kg
ASSEMBLY
CAUTION!
Loading...