PUMP SPRAY OUTFIT
PUMP SPRAY OUTFIT
Model Nos:
CSK2 • CSK6 • CSK10 • CSK15 • CSK20
OPERATING INSTRUCTIONS
0803
SPARE PARTS
Thank you for purchasing this CLARKE Pump Spray outfit, designed for use with
insecticides or other water based products ONLY. NEVER use with flammable liquids.
Please read this leaflet thoroughly to ensure you assemble the unit correctly and
in order that it may be operated in the most efficient manner
Guarantee
This product is guaranteed against faults in manufacture for 12 months from
purchase date. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product has been abused or tampered with
in any way, or not used for the purpose for which it is intended. The reason
for return must be clearly stated.
This guarantee does not affect your statutory rights.
Assembly
Unpack your sprayer and ensure all components are present and that no damage
has occurred in transit. Any damage or deficiency should be reported to your
Clarke dealer immediately.
1. CSK2
This model is fully assembled and ready for use.
2. CSK6
A. Push the hose firmly on to the outlet
connection, and secure using the
spring clip provided.
B. Screw the extension on to the end of
the gun.
Ensure the nozzle on the end of the
extension is screwed firmly in place.
C. Attach the shoulder strap to the two
lugs provided.
CSK2
No. Description Part No.
1 Upper Lid w/Pump VCSK201
2 Lower Lid w/Cylinder VCSK202
3 Operating Lever VCSK203
4 Spring VCSK204
5 Quadrant VCSK205
6 Tube w/Filter VCSK206
7 Spring VCSK207
8 Plunger VCSK208
9 Collar VCSK209
10 End Cap VCSK210
11 Nozzle VCSK211
12 Retainer VCSK212
- Container VCSK213
CSK10
No. Description Part No.
1 Filler Cap VCSK1001
2 Filter VCSK1002
3 Hose Complete VCSK608
4 Spring Clip VCSK606
5 Pump Assy Complete VCSK1005
6 Gun VCSK604
7 Filter VCSK605
8 Extension VCSK609
9 Nozzle VCSK610
10 End Cap VCSK611
11 Harness VCSK1011
12 Harness Hook VCSK1012
13 Plastic Insert VCSK1013
CSK6
No. Description Part No.
1 Relief Valve VCSK601
2 Air Outlet VCSK602
3 Tube VCSK603
4 Gun VCSK604
5 Filter VCSK605
6 Spring Clip VCSK606
7 Pump Assy VCSK607
8 Hose Complete VCSK608
9 Extension VCSK609
10 Nozzle VCSK610
11 End Cap VCSK611
12 Shoulder Strap VCSK612
- Container VCSK613
CSK15 & 20
No. Description Part No.
1 Filler Cap VCSK1001
2 Filter VCSK1002
3 Hose Complete VCSK1503
4 Hose Clip VCSK1504
5 Extension VCSK1505
6 Nozzle VCSK1506
7 End Cap VCSK1507
8 Lever Assy VCSK1508
9 Washer VCSK1509
10 Plunger VCSK1510
11 Cylinder VCSK1511
12 Plastic Insert VCSK1013
13 Harness Hook VCSK1012
14 Harness VCSK1011
15 Pump Assy Complete VCSK1515
2 7
CSK10
CSK15 & CSK 20
3. CSK10
Unscrew the filler cap and remove the various
components
A. Push the hose firmly on to the outlet
connection, and secure using the spring
clip provided.
B. Screw the hose on to the gun - firmly.
C. Screw the extension on to the end of the
gun.
Ensure the nozzle on the end of the
extension is screwed firmly in place.
D. Locate the filter within the
filler neck and temporarily
screw on the filler cap.
E. Attach the harness to the two
hooks provided, threading it as
shown opposite.
F. Fold the harness in half and push the fold
through the elongated hole in the
handle (1).
Push the plastic locking plate into the
fold (2) fully.
Pull the harness so the the locking plate
is pulled firmly into the slot in the handle.
NOTE:
The harness may be threaded through the
elongated hole from either side of the handle.
This allows the harness to hang at either side
of the container, thereby allowing the
pumping handle to be operated by left or
right hand.
CSK 15 & 20
Assembly is similar to that of the CSK10, except a brass gun is used and the hose is
secured with a steel clip. The extension is simply screwed on to the gun.
36
Operation
CSK 2 (2 Litre Capacity)
Unscrew and remove the complete handle and pump assembly, and fill the
container with the desired liquid. Ensure the handle and pump assembly is screwed
back on - firmly.
Pressurise the container by grasping the pump handle on the top of the unit and
pumping briskly.
Depress the lever, within the handle, to produce a spray. When the spray weakens,
pump the handle to maintain container pressure.
CSK 6 (6 Litre Capacity)
Remove the pump assembly by pushing down the pump handle so that the lugs
at the bottom of the assembly engage in the slots in the filler cap. Turn anticlockwise
to open.
Fill with the desired liquid and ensure the pump assembly is screwed back firmly.
Pressurise the container by grasping the pump handle on the top of the unit and
pumping briskly.
Push the lever, on the gun, forward to produce a spray. When the spray weakens,
pump the handle to maintain container pressure
CSK 2
CSK 10, 15 & 20 (10, 15 & 20 Litre Capacity)
Unscrew and remove the filler cap and fill with the desired liquid.
Replace the filler cap, ensuring the filter is in place, and ensure it is firm in order to
provide an air tight seal.
Pump the handle on the side of the unit a few times to pressurise the pump (the
container on these models does not pressurise). DO NOT continue to pump once
the action becomes a little stiff.
If the harness is used, the hooks engage in the recess on the underside of the
container.
Depress the operating lever on the gun to produce a spray - CSK 15 and 20, push
the lever forward - CSK 10.
Pump the handle as necessary in order to maintain pressure in the container so
that a satisfactory spray is produced. It will become obvious as to the pumping
action required to maintain a satisfactory spray.
4 5
CSK 6
Loading...