Clarke CS 250D, CS 550D, 7710155, 7710160 User guide

Page 1
Electronic Digital Safe
CS250D and CS550D
Part Numbers: 7710155 & 7710160
Model Dimensions HxWxD Capacity W e ig h t CS250D 250x350x270 mm 0.018m³ 17.0kg CS550D 557x368x448mm 0.085m³ 33.0kg
This compact safe is ideal for storing cash and important documents in the home or office.
Before permanently securing the safe, check carefully that the keys supplied, are the correct ones for your safe, also check the electronic lock, any defects should be reported to the Clarke dealer where the safe was originally purchased as soon as possible.
IMPORTANT
Store the spare keys safely, make a note of the key serial number in case new keys need to be ordered.
Replacement lock and keys are available from your nearest Clarke dealer. When ordering, please quote the safe model number.
PARTS & SERVICE TEL: 020 8988 7400
or e-mail as follows:
PARTS: Parts@clarkeinternational.com
SERVICE: Service@clarkeinternational.com
Please note that the details and specifications contained herein are correct at the time of going to print. However CLARKE International
reserve the right to change specifications at any time without prior notice.
Page 2
Thank you for purchasing this CLARKE Electronic Digital Safe, which is designed for use in the home and office, as well as in boats and caravans etc.
CLARKE GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Faulty goods should be returned to their place of purchase, no product can be returned to us without prior permission.
This guarantee does not effect your statutory rights.
Battery Installation
Open the safe door using key supplied, see key operation. The battery compartment is found on the back of the door. Slide the cover off in
direction indicated, install batteries observing correct polarity, refit cover and test before closing door .
Operation
heard.
Open Safe (Key Operation)
In the event of battery or electronic failure, the safe can be opened using one of the two keys supplied.
Carefully remove the override cover by prising open with a thin bladed knife or similar, once removed the key lock is exposed. Insert the key and rotate fully anticlockwise, now rotate the knob fully clockwise to open as before. The door can be locked again by reversing the procedure.
NOTE:
When the
batteries need replacing.
Red
and
Amber
LEDs are both illuminated, this indicates that the
IMPORTANT
Never leave the keys inside the safe
LEDs
Red Amber
Green
Open Safe (Keypad)
The entry code keypad followed by button rotated fully clockwise to release the bolts. The door can now be opened. If an incorrect code is entered three times, an audible alarm will sound for 20 seconds. The panel then resets, the correct code can now be entered, if an incorrect code is entered a further three timesthe alarm will sound for five minutes before resetting.
NOTE:
each time a button is pressed an audible beep will sound and the amber LED
will illuminate.
Close Safe
To close the safe, simply close the door and rotate the knob anticlockwise, the door locks automatically, test the lock by attempting to turn the knob clockwise.
Change Entry Code
To change the entry code, open the safe door, using either the key or keypad. Press the red button (Fig. 2), the amber LED will illuminate, enter the new code on the numeric key pad followed by button
NOTE:
the entry code can be a minimum of three and a maximum of eight digits. If the
code entered is less than three or more than eight digits, an audible warning will be
(159)
is factory set. To open the safe, enter
B
, the green LED will illuminate and the knob can be
A.
159
on the numeric
Knob
Override Key Cover
UnlockLock
Numeric Key Pad
Fig. 1
Battery Compartment
Red Button
Fig. 2
Loading...